Revert "serial: 8250: Don't service RX FIFO if interrupts are disabled"

commit 3f2640ed7be838c3f05c0d2b0f7c7508e7431e48 upstream.

This reverts commit 2e9fe539108320820016f78ca7704a7342788380.

Reading LSR unconditionally but processing the error flags only if
UART_IIR_RDI bit was set before in IIR may lead to a loss of transmission
error information on UARTs where the transmission error flags are cleared
by a read of LSR. Information are lost in case an error is detected right
before the read of LSR while processing e.g. an UART_IIR_THRI interrupt.

Signed-off-by: Oliver Barta <o.barta89@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Fixes: 2e9fe5391083 ("serial: 8250: Don't service RX FIFO if interrupts are disabled")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: serial: option: add support for GosunCn ME3630 RNDIS mode

commit aed2a26283528fb69c38e414f649411aa48fb391 upstream.

Added USB IDs for GosunCn ME3630 cellular module in RNDIS mode.

T:  Bus=03 Lev=01 Prnt=01 Port=01 Cnt=03 Dev#= 18 Spd=480 MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=19d2 ProdID=0601 Rev=03.18
S:  Manufacturer=Android
S:  Product=Android
S:  SerialNumber=b950269c
C:  #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=500mA
I:  If#=0x0 Alt= 0 #EPs= 1 Cls=e0(wlcon) Sub=01 Prot=03 Driver=rndis_host
I:  If#=0x1 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=rndis_host
I:  If#=0x2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I:  If#=0x3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#=0x4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option

Signed-off-by: Jörgen Storvist <jorgen.storvist@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: serial: ftdi_sio: add ID for isodebug v1

commit f8377eff548170e8ea8022c067a1fbdf9e1c46a8 upstream.

This adds the vid:pid of the isodebug v1 isolated JTAG/SWD+UART. Only the
second channel is available for use as a serial port.

Signed-off-by: Andreas Fritiofson <andreas.fritiofson@unjo.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mwifiex: Don't abort on small, spec-compliant vendor IEs

commit 63d7ef36103d26f20325a921ecc96a3288560146 upstream.

Per the 802.11 specification, vendor IEs are (at minimum) only required
to contain an OUI. A type field is also included in ieee80211.h (struct
ieee80211_vendor_ie) but doesn't appear in the specification. The
remaining fields (subtype, version) are a convention used in WMM
headers.

Thus, we should not reject vendor-specific IEs that have only the
minimum length (3 bytes) -- we should skip over them (since we only want
to match longer IEs, that match either WMM or WPA formats). We can
reject elements that don't have the minimum-required 3 byte OUI.

While we're at it, move the non-standard subtype and version fields into
the WMM structs, to avoid this confusion in the future about generic
"vendor header" attributes.

Fixes: 685c9b7750bf ("mwifiex: Abort at too short BSS descriptor element")
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mwifiex: Abort at too short BSS descriptor element

commit 685c9b7750bfacd6fc1db50d86579980593b7869 upstream.

Currently mwifiex_update_bss_desc_with_ie() implicitly assumes that
the source descriptor entries contain the enough size for each type
and performs copying without checking the source size.  This may lead
to read over boundary.

Fix this by putting the source size check in appropriate places.

Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Documentation/admin: Remove the vsyscall=native documentation

commit d974ffcfb7447db5f29a4b662a3eaf99a4e1109e upstream.

The vsyscall=native feature is gone -- remove the docs.

Fixes: 076ca272a14c ("x86/vsyscall/64: Drop "native" vsyscalls")
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: Florian Weimer <fweimer@redhat.com>
Cc: Jann Horn <jannh@google.com>
Cc: stable@vger.kernel.org
Cc: Borislav Petkov <bp@alien8.de>
Cc: Kernel Hardening <kernel-hardening@lists.openwall.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: https://lkml.kernel.org/r/d77c7105eb4c57c1a95a95b6a5b8ba194a18e764.1561610354.git.luto@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Documentation: Add section about CPU vulnerabilities for Spectre

commit 6e88559470f581741bcd0f2794f9054814ac9740 upstream.

Add documentation for Spectre vulnerability and the mitigation mechanisms:

- Explain the problem and risks
- Document the mitigation mechanisms
- Document the command line controls
- Document the sysfs files

Co-developed-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Co-developed-by: Tim Chen <tim.c.chen@linux.intel.com>
Signed-off-by: Tim Chen <tim.c.chen@linux.intel.com>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

x86/tls: Fix possible spectre-v1 in do_get_thread_area()

commit 993773d11d45c90cb1c6481c2638c3d9f092ea5b upstream.

The index to access the threads tls array is controlled by userspace
via syscall: sys_ptrace(), hence leading to a potential exploitation
of the Spectre variant 1 vulnerability.

The index can be controlled from:
        ptrace -> arch_ptrace -> do_get_thread_area.

Fix this by sanitizing the user supplied index before using it to access
the p->thread.tls_array.

Signed-off-by: Dianzhang Chen <dianzhangchen0@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: bp@alien8.de
Cc: hpa@zytor.com
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/1561524630-3642-1-git-send-email-dianzhangchen0@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

x86/ptrace: Fix possible spectre-v1 in ptrace_get_debugreg()

commit 31a2fbb390fee4231281b939e1979e810f945415 upstream.

The index to access the threads ptrace_bps is controlled by userspace via
syscall: sys_ptrace(), hence leading to a potential exploitation of the
Spectre variant 1 vulnerability.

The index can be controlled from:
    ptrace -> arch_ptrace -> ptrace_get_debugreg.

Fix this by sanitizing the user supplied index before using it access
thread->ptrace_bps.

Signed-off-by: Dianzhang Chen <dianzhangchen0@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: bp@alien8.de
Cc: hpa@zytor.com
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/1561476617-3759-1-git-send-email-dianzhangchen0@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

perf pmu: Fix uncore PMU alias list for ARM64

commit 599ee18f0740d7661b8711249096db94c09bc508 upstream.

In commit 292c34c10249 ("perf pmu: Fix core PMU alias list for X86
platform"), we fixed the issue of CPU events being aliased to uncore
events.

Fix this same issue for ARM64, since the said commit left the (broken)
behaviour untouched for ARM64.

Signed-off-by: John Garry <john.garry@huawei.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Ben Hutchings <ben@decadent.org.uk>
Cc: Hendrik Brueckner <brueckner@linux.ibm.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Shaokun Zhang <zhangshaokun@hisilicon.com>
Cc: Thomas Richter <tmricht@linux.ibm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linuxarm@huawei.com
Cc: stable@vger.kernel.org
Fixes: 292c34c10249 ("perf pmu: Fix core PMU alias list for X86 platform")
Link: http://lkml.kernel.org/r/1560521283-73314-2-git-send-email-john.garry@huawei.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

block, bfq: NULL out the bic when it's no longer valid

commit dbc3117d4ca9e17819ac73501e914b8422686750 upstream.

In reboot tests on several devices we were seeing a "use after free"
when slub_debug or KASAN was enabled.  The kernel complained about:

  Unable to handle kernel paging request at virtual address 6b6b6c2b

...which is a classic sign of use after free under slub_debug.  The
stack crawl in kgdb looked like:

 0  test_bit (addr=<optimized out>, nr=<optimized out>)
 1  bfq_bfqq_busy (bfqq=<optimized out>)
 2  bfq_select_queue (bfqd=<optimized out>)
 3  __bfq_dispatch_request (hctx=<optimized out>)
 4  bfq_dispatch_request (hctx=<optimized out>)
 5  0xc056ef00 in blk_mq_do_dispatch_sched (hctx=0xed249440)
 6  0xc056f728 in blk_mq_sched_dispatch_requests (hctx=0xed249440)
 7  0xc0568d24 in __blk_mq_run_hw_queue (hctx=0xed249440)
 8  0xc0568d94 in blk_mq_run_work_fn (work=<optimized out>)
 9  0xc024c5c4 in process_one_work (worker=0xec6d4640, work=0xed249480)
 10 0xc024cff4 in worker_thread (__worker=0xec6d4640)

Digging in kgdb, it could be found that, though bfqq looked fine,
bfqq->bic had been freed.

Through further digging, I postulated that perhaps it is illegal to
access a "bic" (AKA an "icq") after bfq_exit_icq() had been called
because the "bic" can be freed at some point in time after this call
is made.  I confirmed that there certainly were cases where the exact
crashing code path would access the "bic" after bfq_exit_icq() had
been called.  Sspecifically I set the "bfqq->bic" to (void *)0x7 and
saw that the bic was 0x7 at the time of the crash.

To understand a bit more about why this crash was fairly uncommon (I
saw it only once in a few hundred reboots), you can see that much of
the time bfq_exit_icq_fbqq() fully frees the bfqq and thus it can't
access the ->bic anymore.  The only case it doesn't is if
bfq_put_queue() sees a reference still held.

However, even in the case when bfqq isn't freed, the crash is still
rare.  Why?  I tracked what happened to the "bic" after the exit
routine.  It doesn't get freed right away.  Rather,
put_io_context_active() eventually called put_io_context() which
queued up freeing on a workqueue.  The freeing then actually happened
later than that through call_rcu().  Despite all these delays, some
extra debugging showed that all the hoops could be jumped through in
time and the memory could be freed causing the original crash.  Phew!

To make a long story short, assuming it truly is illegal to access an
icq after the "exit_icq" callback is finished, this patch is needed.

Cc: stable@vger.kernel.org
Reviewed-by: Paolo Valente <paolo.valente@unimore.it>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: hda/realtek - Headphone Mic can't record after S3

commit d07a9a4f66e944fcc900812cbc2f6817bde6a43d upstream.

Dell headset mode platform with ALC236.
It doesn't recording after system resume from S3.
S3 mode was deep. s2idle was not has this issue.
S3 deep will cut of codec power. So, the register will back to default
after resume back.
This patch will solve this issue.

Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: usb-audio: Fix parse of UAC2 Extension Units

commit ca95c7bf3d29716916baccdc77c3c2284b703069 upstream.

Extension Unit (XU) is used to have a compatible layout with
Processing Unit (PU) on UAC1, and the usb-audio driver code assumed it
for parsing the descriptors.  Meanwhile, on UAC2, XU became slightly
incompatible with PU; namely, XU has a one-byte bmControls bitmap
while PU has two bytes bmControls bitmap.  This incompatibility
results in the read of a wrong address for the last iExtension field,
which ended up with an incorrect string for the mixer element name, as
recently reported for Focusrite Scarlett 18i20 device.

This patch corrects this misalignment by introducing a couple of new
macros and calling them depending on the descriptor type.

Fixes: 23caaf19b11e ("ALSA: usb-mixer: Add support for Audio Class v2.0")
Reported-by: Stefan Sauer <ensonic@hora-obscura.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

media: stv0297: fix frequency range limit

commit b09a2ab2baeb36bf7ef7780405ad172281741c7c upstream.

There was a typo at the lower frequency limit for a DVB-C
card, causing the driver to fail while tuning channels at the
VHF range.

https://bugzilla.kernel.org/show_bug.cgi?id=202083

Fixes: f1b1eabff0eb ("media: dvb: represent min/max/step/tolerance freqs in Hz")
Reported-by: Ari Kohtamäki <ari.kohtamaki@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

udf: Fix incorrect final NOT_ALLOCATED (hole) extent length

commit fa33cdbf3eceb0206a4f844fe91aeebcf6ff2b7a upstream.

In some cases, using the 'truncate' command to extend a UDF file results
in a mismatch between the length of the file's extents (specifically, due
to incorrect length of the final NOT_ALLOCATED extent) and the information
(file) length. The discrepancy can prevent other operating systems
(i.e., Windows 10) from opening the file.

Two particular errors have been observed when extending a file:

1. The final extent is larger than it should be, having been rounded up
   to a multiple of the block size.

B. The final extent is not shorter than it should be, due to not having
   been updated when the file's information length was increased.

[JK: simplified udf_do_extend_final_block(), fixed up some types]

Fixes: 2c948b3f86e5 ("udf: Avoid IO in udf_clear_inode")
CC: stable@vger.kernel.org
Signed-off-by: Steven J. Magnani <steve@digidescorp.com>
Link: https://lore.kernel.org/r/1561948775-5878-1-git-send-email-steve@digidescorp.com
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

fscrypt: don't set policy for a dead directory

commit 5858bdad4d0d0fc18bf29f34c3ac836e0b59441f upstream.

The directory may have been removed when entering
fscrypt_ioctl_set_policy().  If so, the empty_dir() check will return
error for ext4 file system.

ext4_rmdir() sets i_size = 0, then ext4_empty_dir() reports an error
because 'inode->i_size < EXT4_DIR_REC_LEN(1) + EXT4_DIR_REC_LEN(2)'.  If
the fs is mounted with errors=panic, it will trigger a panic issue.

Add the check IS_DEADDIR() to fix this problem.

Fixes: 9bd8212f981e ("ext4 crypto: add encryption policy and password salt support")
Cc: <stable@vger.kernel.org> # v4.1+
Signed-off-by: Hongjie Fang <hongjiefang@asrmicro.com>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net :sunrpc :clnt :Fix xps refcount imbalance on the error path

[ Upstream commit b96226148491505318228ac52624956bd98f9e0c ]

rpc_clnt_add_xprt take a reference to struct rpc_xprt_switch, but forget
to release it before return, may lead to a memory leak.

Signed-off-by: Lin Yi <teroincn@163.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

NFS4: Only set creation opendata if O_CREAT

[ Upstream commit 909105199a682cb09c500acd443d34b182846c9c ]

We can end up in nfs4_opendata_alloc during task exit, in which case
current->fs has already been cleaned up.  This leads to a crash in
current_umask().

Fix this by only setting creation opendata if we are actually doing an open
with O_CREAT.  We can drop the check for NULL nfs4_open_createattrs, since
O_CREAT will never be set for the recovery path.

Suggested-by: Trond Myklebust <trondmy@hammerspace.com>
Signed-off-by: Benjamin Coddington <bcodding@redhat.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: dsa: mv88e6xxx: fix shift of FID bits in mv88e6185_g1_vtu_loadpurge()

[ Upstream commit 48620e341659f6e4b978ec229f6944dabe6df709 ]

The comment is correct, but the code ends up moving the bits four
places too far, into the VTUOp field.

Fixes: 11ea809f1a74 (net: dsa: mv88e6xxx: support 256 databases)
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

quota: fix a problem about transfer quota

[ Upstream commit c6d9c35d16f1bafd3fec64b865e569e48cbcb514 ]

Run below script as root, dquot_add_space will return -EDQUOT since
__dquot_transfer call dquot_add_space with flags=0, and dquot_add_space
think it's a preallocation. Fix it by set flags as DQUOT_SPACE_WARN.

mkfs.ext4 -O quota,project /dev/vdb
mount -o prjquota /dev/vdb /mnt
setquota -P 23 1 1 0 0 /dev/vdb
dd if=/dev/zero of=/mnt/test-file bs=4K count=1
chattr -p 23 test-file

Fixes: 7b9ca4c61bc2 ("quota: Reduce contention on dq_data_lock")
Signed-off-by: yangerkun <yangerkun@huawei.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>

scsi: qedi: Check targetname while finding boot target information

[ Upstream commit 1ac3549ed58cdfdaf43bbf31ac260e2381cc0dae ]

The kernel panic was observed during iSCSI discovery via offload with below
call trace,

[ 2115.646901] BUG: unable to handle kernel NULL pointer dereference at (null)
[ 2115.646909] IP: [<ffffffffacf7f0cc>] strncmp+0xc/0x60
[ 2115.646927] PGD 0
[ 2115.646932] Oops: 0000 [#1] SMP
[ 2115.647107] CPU: 24 PID: 264 Comm: kworker/24:1 Kdump: loaded Tainted: G
               OE  ------------   3.10.0-957.el7.x86_64 #1
[ 2115.647133] Workqueue: slowpath-13:00. qed_slowpath_task [qed]
[ 2115.647135] task: ffff8d66af80b0c0 ti: ffff8d66afb80000 task.ti: ffff8d66afb80000
[ 2115.647136] RIP: 0010:[<ffffffffacf7f0cc>]  [<ffffffffacf7f0cc>] strncmp+0xc/0x60
[ 2115.647141] RSP: 0018:ffff8d66afb83c68  EFLAGS: 00010206
[ 2115.647143] RAX: 0000000000000001 RBX: 0000000000000007 RCX: 000000000000000a
[ 2115.647144] RDX: 0000000000000100 RSI: 0000000000000000 RDI: ffff8d632b3ba040
[ 2115.647145] RBP: ffff8d66afb83c68 R08: 0000000000000000 R09: 000000000000ffff
[ 2115.647147] R10: 0000000000000007 R11: 0000000000000800 R12: ffff8d66a30007a0
[ 2115.647148] R13: ffff8d66747a3c10 R14: ffff8d632b3ba000 R15: ffff8d66747a32f8
[ 2115.647149] FS:  0000000000000000(0000) GS:ffff8d66aff00000(0000) knlGS:0000000000000000
[ 2115.647151] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 2115.647152] CR2: 0000000000000000 CR3: 0000000509610000 CR4: 00000000007607e0
[ 2115.647153] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 2115.647154] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 2115.647155] PKRU: 00000000
[ 2115.647157] Call Trace:
[ 2115.647165]  [<ffffffffc0634cc5>] qedi_get_protocol_tlv_data+0x2c5/0x510 [qedi]
[ 2115.647184]  [<ffffffffc05968f5>] ? qed_mfw_process_tlv_req+0x245/0xbe0 [qed]
[ 2115.647195]  [<ffffffffc05496cb>] qed_mfw_fill_tlv_data+0x4b/0xb0 [qed]
[ 2115.647206]  [<ffffffffc0596911>] qed_mfw_process_tlv_req+0x261/0xbe0 [qed]
[ 2115.647215]  [<ffffffffacce0e8e>] ? dequeue_task_fair+0x41e/0x660
[ 2115.647221]  [<ffffffffacc2a59e>] ? __switch_to+0xce/0x580
[ 2115.647230]  [<ffffffffc0546013>] qed_slowpath_task+0xa3/0x160 [qed]
[ 2115.647278] RIP  [<ffffffffacf7f0cc>] strncmp+0xc/0x60

Fix kernel panic by validating the session targetname before providing TLV
data and confirming the presence of boot targets.

Signed-off-by: Nilesh Javali <njavali@marvell.com>
Reviewed-by: Lee Duncan <lduncan@suse.com>
Reviewed-by: Chris Leech <cleech@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: lio_core: fix potential sign-extension overflow on large shift

[ Upstream commit 9476274093a0e79b905f4cd6cf6d149f65e02c17 ]

Left shifting the signed int value 1 by 31 bits has undefined behaviour
and the shift amount oq_no can be as much as 63.  Fix this by using
BIT_ULL(oq_no) instead.

Addresses-Coverity: ("Bad shift operation")
Fixes: f21fb3ed364b ("Add support of Cavium Liquidio ethernet adapters")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ip6_tunnel: allow not to count pkts on tstats by passing dev as NULL

[ Upstream commit 6f6a8622057c92408930c31698394fae1557b188 ]

A similar fix to Patch "ip_tunnel: allow not to count pkts on tstats by
setting skb's dev to NULL" is also needed by ip6_tunnel.

Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm: return -EFAULT if copy_to_user() fails

[ Upstream commit 74b67efa8d7b4f90137f0ab9a80dd319da050350 ]

The copy_from_user() function returns the number of bytes remaining
to be copied but we want to return a negative error code.  Otherwise
the callers treat it as a successful copy.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190618131843.GA29463@mwanda
Signed-off-by: Sasha Levin <sashal@kernel.org>

bnx2x: Check if transceiver implements DDM before access

[ Upstream commit cf18cecca911c0db96b868072665347efe6df46f ]

Some transceivers may comply with SFF-8472 even though they do not
implement the Digital Diagnostic Monitoring (DDM) interface described in
the spec. The existence of such area is specified by the 6th bit of byte
92, set to 1 if implemented.

Currently, without checking this bit, bnx2x fails trying to read sfp
module's EEPROM with the follow message:

ethtool -m enP5p1s0f1
Cannot get Module EEPROM data: Input/output error

Because it fails to read the additional 256 bytes in which it is assumed
to exist the DDM data.

This issue was noticed using a Mellanox Passive DAC PN 01FT738. The EEPROM
data was confirmed by Mellanox as correct and similar to other Passive
DACs from other manufacturers.

Signed-off-by: Mauro S. M. Rodrigues <maurosr@linux.vnet.ibm.com>
Acked-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

md: fix for divide error in status_resync

[ Upstream commit 9642fa73d073527b0cbc337cc17a47d545d82cd2 ]

Stopping external metadata arrays during resync/recovery causes
retries, loop of interrupting and starting reconstruction, until it
hit at good moment to stop completely. While these retries
curr_mark_cnt can be small- especially on HDD drives, so subtraction
result can be smaller than 0. However it is casted to uint without
checking. As a result of it the status bar in /proc/mdstat while stopping
is strange (it jumps between 0% and 99%).

The real problem occurs here after commit 72deb455b5ec ("block: remove
CONFIG_LBDAF"). Sector_div() macro has been changed, now the
divisor is casted to uint32. For db = -8 the divisior(db/32-1) becomes 0.

Check if db value can be really counted and replace these macro by
div64_u64() inline.

Signed-off-by: Mariusz Tkaczyk <mariusz.tkaczyk@intel.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

mmc: core: complete HS400 before checking status

[ Upstream commit b0e370b95a3b231d0fb5d1958cce85ef57196fe6 ]

We don't have a reproducible error case, yet our BSP team suggested that
the mmc_switch_status() command in mmc_select_hs400() should come after
the callback into the driver completing HS400 setup. It makes sense to
me because we want the status of a fully setup HS400, so it will
increase the reliability of the mmc_switch_status() command.

Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Fixes: ba6c7ac3a2f4 ("mmc: core: more fine-grained hooks for HS400 tuning")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

qmi_wwan: extend permitted QMAP mux_id value range

[ Upstream commit 36815b416fa48766ac5a98e4b2dc3ebc5887222e ]

Permit mux_id values up to 254 to be used in qmimux_register_device()
for compatibility with ip(8) and the rmnet driver.

Fixes: c6adf77953bc ("net: usb: qmi_wwan: add qmap mux protocol support")
Cc: Daniele Palmas <dnlplm@gmail.com>
Signed-off-by: Reinhard Speyerer <rspmn@arcor.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

qmi_wwan: avoid RCU stalls on device disconnect when in QMAP mode

[ Upstream commit a8fdde1cb830e560208af42b6c10750137f53eb3 ]

Switch qmimux_unregister_device() and qmi_wwan_disconnect() to
use unregister_netdevice_queue() and unregister_netdevice_many()
instead of unregister_netdevice(). This avoids RCU stalls which
have been observed on device disconnect in certain setups otherwise.

Fixes: c6adf77953bc ("net: usb: qmi_wwan: add qmap mux protocol support")
Cc: Daniele Palmas <dnlplm@gmail.com>
Signed-off-by: Reinhard Speyerer <rspmn@arcor.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

qmi_wwan: add support for QMAP padding in the RX path

[ Upstream commit 61356088ace1866a847a727d4d40da7bf00b67fc ]

The QMAP code in the qmi_wwan driver is based on the CodeAurora GobiNet
driver which does not process QMAP padding in the RX path correctly.
Add support for QMAP padding to qmimux_rx_fixup() according to the
description of the rmnet driver.

Fixes: c6adf77953bc ("net: usb: qmi_wwan: add qmap mux protocol support")
Cc: Daniele Palmas <dnlplm@gmail.com>
Signed-off-by: Reinhard Speyerer <rspmn@arcor.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

bpf, x64: fix stack layout of JITed bpf code

[ Upstream commit fe8d9571dc50232b569242fac7ea6332a654f186 ]

Since commit 177366bf7ceb the %rbp stopped pointing to %rbp of the
previous stack frame. That broke frame pointer based stack unwinding.
This commit is a partial revert of it.
Note that the location of tail_call_cnt is fixed, since the verifier
enforces MAX_BPF_STACK stack size for programs with tail calls.

Fixes: 177366bf7ceb ("bpf: change x86 JITed program stack layout")
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

bpf, devmap: Add missing RCU read lock on flush

[ Upstream commit 86723c8640633bee4b4588d3c7784ee7a0032f65 ]

.ndo_xdp_xmit() assumes it is called under RCU. For example virtio_net
uses RCU to detect it has setup the resources for tx. The assumption
accidentally broke when introducing bulk queue in devmap.

Fixes: 5d053f9da431 ("bpf: devmap prepare xdp frames for bulking")
Reported-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Toshiaki Makita <toshiaki.makita1@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

bpf, devmap: Add missing bulk queue free

[ Upstream commit edabf4d9dd905acd60048ea1579943801e3a4876 ]

dev_map_free() forgot to free bulk queue when freeing its entries.

Fixes: 5d053f9da431 ("bpf: devmap prepare xdp frames for bulking")
Signed-off-by: Toshiaki Makita <toshiaki.makita1@gmail.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

bpf, devmap: Fix premature entry free on destroying map

[ Upstream commit d4dd153d551634683fccf8881f606fa9f3dfa1ef ]

dev_map_free() waits for flush_needed bitmap to be empty in order to
ensure all flush operations have completed before freeing its entries.
However the corresponding clear_bit() was called before using the
entries, so the entries could be used after free.

All access to the entries needs to be done before clearing the bit.
It seems commit a5e2da6e9787 ("bpf: netdev is never null in
__dev_map_flush") accidentally changed the clear_bit() and memory access
order.

Note that the problem happens only in __dev_map_flush(), not in
dev_map_flush_old(). dev_map_flush_old() is called only after nulling
out the corresponding netdev_map entry, so dev_map_free() never frees
the entry thus no such race happens there.

Fixes: a5e2da6e9787 ("bpf: netdev is never null in __dev_map_flush")
Signed-off-by: Toshiaki Makita <toshiaki.makita1@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

mac80211: do not start any work during reconfigure flow

[ Upstream commit f8891461a277ec0afc493fd30cd975a38048a038 ]

It is not a good idea to try to perform any work (e.g. send an auth
frame) during reconfigure flow.

Prevent this from happening, and at the end of the reconfigure flow
requeue all the works.

Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

mac80211: only warn once on chanctx_conf being NULL

[ Upstream commit 563572340173865a9a356e6bb02579e6998a876d ]

In multiple SSID cases, it takes time to prepare every AP interface
to be ready in initializing phase. If a sta already knows everything it
needs to join one of the APs and sends authentication to the AP which
is not fully prepared at this point of time, AP's channel context
could be NULL. As a result, warning message occurs.

Even worse, if the AP is under attack via tools such as MDK3 and massive
authentication requests are received in a very short time, console will
be hung due to kernel warning messages.

WARN_ON_ONCE() could be a better way for indicating warning messages
without duplicate messages to flood the console.

Johannes: We still need to address the underlying problem, but we
          don't really have a good handle on it yet. Suppress the
          worst side-effects for now.

Signed-off-by: Zhi Chen <zhichen@codeaurora.org>
Signed-off-by: Yibo Zhao <yiboz@codeaurora.org>
[johannes: add note, change subject]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: davinci: da8xx: specify dma_coherent_mask for lcdc

[ Upstream commit 68f2515bb31a664ba3e2bc1eb78dd9f529b10067 ]

The lcdc device is missing the dma_coherent_mask definition causing the
following warning on da850-evm:

da8xx_lcdc da8xx_lcdc.0: found Sharp_LK043T1DG01 panel
------------[ cut here ]------------
WARNING: CPU: 0 PID: 1 at kernel/dma/mapping.c:247 dma_alloc_attrs+0xc8/0x110
Modules linked in:
CPU: 0 PID: 1 Comm: swapper Not tainted 5.2.0-rc3-00077-g16d72dd4891f #18
Hardware name: DaVinci DA850/OMAP-L138/AM18x EVM
[<c000fce8>] (unwind_backtrace) from [<c000d900>] (show_stack+0x10/0x14)
[<c000d900>] (show_stack) from [<c001a4f8>] (__warn+0xec/0x114)
[<c001a4f8>] (__warn) from [<c001a634>] (warn_slowpath_null+0x3c/0x48)
[<c001a634>] (warn_slowpath_null) from [<c0065860>] (dma_alloc_attrs+0xc8/0x110)
[<c0065860>] (dma_alloc_attrs) from [<c02820f8>] (fb_probe+0x228/0x5a8)
[<c02820f8>] (fb_probe) from [<c02d3e9c>] (platform_drv_probe+0x48/0x9c)
[<c02d3e9c>] (platform_drv_probe) from [<c02d221c>] (really_probe+0x1d8/0x2d4)
[<c02d221c>] (really_probe) from [<c02d2474>] (driver_probe_device+0x5c/0x168)
[<c02d2474>] (driver_probe_device) from [<c02d2728>] (device_driver_attach+0x58/0x60)
[<c02d2728>] (device_driver_attach) from [<c02d27b0>] (__driver_attach+0x80/0xbc)
[<c02d27b0>] (__driver_attach) from [<c02d047c>] (bus_for_each_dev+0x64/0xb4)
[<c02d047c>] (bus_for_each_dev) from [<c02d1590>] (bus_add_driver+0xe4/0x1d8)
[<c02d1590>] (bus_add_driver) from [<c02d301c>] (driver_register+0x78/0x10c)
[<c02d301c>] (driver_register) from [<c000a5c0>] (do_one_initcall+0x48/0x1bc)
[<c000a5c0>] (do_one_initcall) from [<c05cae6c>] (kernel_init_freeable+0x10c/0x1d8)
[<c05cae6c>] (kernel_init_freeable) from [<c048a000>] (kernel_init+0x8/0xf4)
[<c048a000>] (kernel_init) from [<c00090e0>] (ret_from_fork+0x14/0x34)
Exception stack(0xc6837fb0 to 0xc6837ff8)
7fa0:                                     00000000 00000000 00000000 00000000
7fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
7fe0: 00000000 00000000 00000000 00000000 00000013 00000000
---[ end trace 8a8073511be81dd2 ]---

Add a 32-bit mask to the platform device's definition.

Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: davinci: da850-evm: call regulator_has_full_constraints()

[ Upstream commit 0c0c9b5753cd04601b17de09da1ed2885a3b42fe ]

The BB expander at 0x21 i2c bus 1 fails to probe on da850-evm because
the board doesn't set has_full_constraints to true in the regulator
API.

Call regulator_has_full_constraints() at the end of board registration
just like we do in da850-lcdk and da830-evm.

Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

mlxsw: spectrum: Disallow prio-tagged packets when PVID is removed

[ Upstream commit 4b14cc313f076c37b646cee06a85f0db59cf216c ]

When PVID is removed from a bridge port, the Linux bridge drops both
untagged and prio-tagged packets. Align mlxsw with this behavior.

Fixes: 148f472da5db ("mlxsw: reg: Add the Switch Port Acceptable Frame Types register")
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

KVM: arm/arm64: vgic: Fix kvm_device leak in vgic_its_destroy

[ Upstream commit 4729ec8c1e1145234aeeebad5d96d77f4ccbb00a ]

kvm_device->destroy() seems to be supposed to free its kvm_device
struct, but vgic_its_destroy() is not currently doing this,
resulting in a memory leak, resulting in kmemleak reports such as
the following:

unreferenced object 0xffff800aeddfe280 (size 128):
  comm "qemu-system-aar", pid 13799, jiffies 4299827317 (age 1569.844s)
  [...]
  backtrace:
    [<00000000a08b80e2>] kmem_cache_alloc+0x178/0x208
    [<00000000dcad2bd3>] kvm_vm_ioctl+0x350/0xbc0

Fix it.

Cc: Andre Przywara <andre.przywara@arm.com>
Fixes: 1085fdc68c60 ("KVM: arm64: vgic-its: Introduce new KVM ITS device")
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

Input: imx_keypad - make sure keyboard can always wake up system

[ Upstream commit ce9a53eb3dbca89e7ad86673d94ab886e9bea704 ]

There are several scenarios that keyboard can NOT wake up system
from suspend, e.g., if a keyboard is depressed between system
device suspend phase and device noirq suspend phase, the keyboard
ISR will be called and both keyboard depress and release interrupts
will be disabled, then keyboard will no longer be able to wake up
system. Another scenario would be, if a keyboard is kept depressed,
and then system goes into suspend, the expected behavior would be
when keyboard is released, system will be waked up, but current
implementation can NOT achieve that, because both depress and release
interrupts are disabled in ISR, and the event check is still in
progress.

To fix these issues, need to make sure keyboard's depress or release
interrupt is enabled after noirq device suspend phase, this patch
moves the suspend/resume callback to noirq suspend/resume phase, and
enable the corresponding interrupt according to current keyboard status.

Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

riscv: Fix udelay in RV32.

[ Upstream commit d0e1f2110a5eeb6e410b2dd37d98bc5b30da7bc7 ]

In RV32, udelay would delay the wrong cycle. When it shifts right
"UDELAY_SHIFT" bits, it either delays 0 cycle or 1 cycle. It only works
correctly in RV64. Because the 'ucycles' always needs to be 64 bits
variable.

Signed-off-by: Nick Hu <nickhu@andestech.com>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
[paul.walmsley@sifive.com: fixed minor spelling error]
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/vmwgfx: fix a warning due to missing dma_parms

[ Upstream commit 39916897cd815a0ee07ba1f6820cf88a63e459fc ]

Booting up with DMA_API_DEBUG_SG=y generates a warning due to the driver
forgot to set dma_parms appropriately. Set it just after vmw_dma_masks()
in vmw_driver_load().

DMA-API: vmwgfx 0000:00:0f.0: mapping sg segment longer than device
claims to support [len=2097152] [max=65536]
WARNING: CPU: 2 PID: 261 at kernel/dma/debug.c:1232
debug_dma_map_sg+0x360/0x480
Hardware name: VMware, Inc. VMware Virtual Platform/440BX Desktop
Reference Platform, BIOS 6.00 04/13/2018
RIP: 0010:debug_dma_map_sg+0x360/0x480
Call Trace:
 vmw_ttm_map_dma+0x3b1/0x5b0 [vmwgfx]
 vmw_bo_map_dma+0x25/0x30 [vmwgfx]
 vmw_otables_setup+0x2a8/0x750 [vmwgfx]
 vmw_request_device_late+0x78/0xc0 [vmwgfx]
 vmw_request_device+0xee/0x4e0 [vmwgfx]
 vmw_driver_load.cold+0x757/0xd84 [vmwgfx]
 drm_dev_register+0x1ff/0x340 [drm]
 drm_get_pci_dev+0x110/0x290 [drm]
 vmw_probe+0x15/0x20 [vmwgfx]
 local_pci_probe+0x7a/0xc0
 pci_device_probe+0x1b9/0x290
 really_probe+0x1b5/0x630
 driver_probe_device+0xa3/0x1a0
 device_driver_attach+0x94/0xa0
 __driver_attach+0xdd/0x1c0
 bus_for_each_dev+0xfe/0x150
 driver_attach+0x2d/0x40
 bus_add_driver+0x290/0x350
 driver_register+0xdc/0x1d0
 __pci_register_driver+0xda/0xf0
 vmwgfx_init+0x34/0x1000 [vmwgfx]
 do_one_initcall+0xe5/0x40a
 do_init_module+0x10f/0x3a0
 load_module+0x16a5/0x1a40
 __se_sys_finit_module+0x183/0x1c0
 __x64_sys_finit_module+0x43/0x50
 do_syscall_64+0xc8/0x606
 entry_SYSCALL_64_after_hwframe+0x44/0xa9

Fixes: fb1d9738ca05 ("drm/vmwgfx: Add DRM driver for VMware Virtual GPU")
Co-developed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Qian Cai <cai@lca.pw>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/vmwgfx: Honor the sg list segment size limitation

[ Upstream commit bde15555ba61c7f664f40fd3c6fdbdb63f784c9b ]

When building sg tables, honor the device sg list segment size limitation.

Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Deepak Rawat <drawat@vmware.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

s390/boot: disable address-of-packed-member warning

[ Upstream commit f9364df30420987e77599c4789ec0065c609a507 ]

Get rid of gcc9 warnings like this:

arch/s390/boot/ipl_report.c: In function 'find_bootdata_space':
arch/s390/boot/ipl_report.c:42:26: warning: taking address of packed member of 'struct ipl_rb_components' may result in an unaligned pointer value [-Waddress-of-packed-member]
   42 |  for_each_rb_entry(comp, comps)
      |                          ^~~~~

This is effectively the s390 variant of commit 20c6c1890455
("x86/boot: Disable the address-of-packed-member compiler warning").

Reviewed-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: dts: am335x phytec boards: Fix cd-gpios active level

[ Upstream commit 8a0098c05a272c9a68f6885e09755755b612459c ]

Active level of the mmc1 cd gpio needs to be low instead of high.
Fix PCM-953 and phyBOARD-WEGA.

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ibmvnic: Fix unchecked return codes of memory allocations

[ Upstream commit 7c940b1a5291e5069d561f5b8f0e51db6b7a259a ]

The return values for these memory allocations are unchecked,
which may cause an oops if the driver does not handle them after
a failure. Fix by checking the function's return code.

Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ibmvnic: Refresh device multicast list after reset

[ Upstream commit be32a24372cf162e825332da1a7ccef058d4f20b ]

It was observed that multicast packets were no longer received after
a device reset.  The fix is to resend the current multicast list to
the backing device after recovery.

Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ibmvnic: Do not close unopened driver during reset

[ Upstream commit 1f94608b0ce141be5286dde31270590bdf35b86a ]

Check driver state before halting it during a reset. If the driver is
not running, do nothing. Otherwise, a request to deactivate a down link
can cause an error and the reset will fail.

Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: phy: rename Asix Electronics PHY driver

[ Upstream commit a9520543b123bbd7275a0ab8d0375a5412683b41 ]

[Resent to net instead of net-next - may clash with Anders Roxell's patch
series addressing duplicate module names]

Commit 31dd83b96641 ("net-next: phy: new Asix Electronics PHY driver")
introduced a new PHY driver drivers/net/phy/asix.c that causes a module
name conflict with a pre-existiting driver (drivers/net/usb/asix.c).

The PHY driver is used by the X-Surf 100 ethernet card driver, and loaded
by that driver via its PHY ID. A rename of the driver looks unproblematic.

Rename PHY driver to ax88796b.c in order to resolve name conflict.

Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Fixes: 31dd83b96641 ("net-next: phy: new Asix Electronics PHY driver")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

can: af_can: Fix error path of can_init()

[ Upstream commit c5a3aed1cd3152429348ee1fe5cdcca65fe901ce ]

This patch add error path for can_init() to avoid possible crash if some
error occurs.

Fixes: 0d66548a10cb ("[CAN]: Add PF_CAN core module")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

can: m_can: implement errata "Needless activation of MRAF irq"

[ Upstream commit 3e82f2f34c930a2a0a9e69fdc2de2f2f1388b442 ]

During frame reception while the MCAN is in Error Passive state and the
Receive Error Counter has thevalue MCAN_ECR.REC = 127, it may happen
that MCAN_IR.MRAF is set although there was no Message RAM access
failure. If MCAN_IR.MRAF is enabled, an interrupt to the Host CPU is
generated.

Work around:
The Message RAM Access Failure interrupt routine needs to check whether

    MCAN_ECR.RP = '1' and MCAN_ECR.REC = '127'.

In this case, reset MCAN_IR.MRAF. No further action is required.
This affects versions older than 3.2.0

Errata explained on Sama5d2 SoC which includes this hardware block:
http://ww1.microchip.com/downloads/en/DeviceDoc/SAMA5D2-Family-Silicon-Errata-and-Data-Sheet-Clarification-DS80000803B.pdf
chapter 6.2

Reproducibility: If 2 devices with m_can are connected back to back,
configuring different bitrate on them will lead to interrupt storm on
the receiving side, with error "Message RAM access failure occurred".
Another way is to have a bad hardware connection. Bad wire connection
can lead to this issue as well.

This patch fixes the issue according to provided workaround.

Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

can: mcp251x: add support for mcp25625

[ Upstream commit 35b7fa4d07c43ad79b88e6462119e7140eae955c ]

Fully compatible with mcp2515, the mcp25625 have integrated transceiver.

This patch adds support for the mcp25625 to the existing mcp251x driver.

Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

dt-bindings: can: mcp251x: add mcp25625 support

[ Upstream commit 0df82dcd55832a99363ab7f9fab954fcacdac3ae ]

Fully compatible with mcp2515, the mcp25625 have integrated transceiver.

This patch add the mcp25625 to the device tree bindings documentation.

Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

soundwire: intel: set dai min and max channels correctly

[ Upstream commit 39194128701bf2af9bbc420ffe6e3cb5d2c16061 ]

Looks like there is a copy paste error.
This patch fixes it!

Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

mwifiex: Fix heap overflow in mwifiex_uap_parse_tail_ies()

[ Upstream commit 69ae4f6aac1578575126319d3f55550e7e440449 ]

A few places in mwifiex_uap_parse_tail_ies() perform memcpy()
unconditionally, which may lead to either buffer overflow or read over
boundary.

This patch addresses the issues by checking the read size and the
destination size at each place more properly.  Along with the fixes,
the patch cleans up the code slightly by introducing a temporary
variable for the token size, and unifies the error path with the
standard goto statement.

Reported-by: huangwen <huangwen@venustech.com.cn>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

iwlwifi: Fix double-free problems in iwl_req_fw_callback()

[ Upstream commit a8627176b0de7ba3f4524f641ddff4abf23ae4e4 ]

In the error handling code of iwl_req_fw_callback(), iwl_dealloc_ucode()
is called to free data. In iwl_drv_stop(), iwl_dealloc_ucode() is called
again, which can cause double-free problems.

To fix this bug, the call to iwl_dealloc_ucode() in
iwl_req_fw_callback() is deleted.

This bug is found by a runtime fuzzing tool named FIZZER written by us.

Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

mwifiex: Fix possible buffer overflows at parsing bss descriptor

[ Upstream commit 13ec7f10b87f5fc04c4ccbd491c94c7980236a74 ]

mwifiex_update_bss_desc_with_ie() calls memcpy() unconditionally in
a couple places without checking the destination size.  Since the
source is given from user-space, this may trigger a heap buffer
overflow.

Fix it by putting the length check before performing memcpy().

This fix addresses CVE-2019-3846.

Reported-by: huangwen <huangwen@venustech.com.cn>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

mac80211: free peer keys before vif down in mesh

[ Upstream commit 0112fa557c3bb3a002bc85760dc3761d737264d3 ]

freeing peer keys after vif down is resulting in peer key uninstall
to fail due to interface lookup failure. so fix that.

Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

mac80211: mesh: fix RCU warning

[ Upstream commit 551842446ed695641a00782cd118cbb064a416a1 ]

ifmsh->csa is an RCU-protected pointer. The writer context
in ieee80211_mesh_finish_csa() is already mutually
exclusive with wdev->sdata.mtx, but the RCU checker did
not know this. Use rcu_dereference_protected() to avoid a
warning.

fixes the following warning:

[   12.519089] =============================
[   12.520042] WARNING: suspicious RCU usage
[   12.520652] 5.1.0-rc7-wt+ #16 Tainted: G        W
[   12.521409] -----------------------------
[   12.521972] net/mac80211/mesh.c:1223 suspicious rcu_dereference_check() usage!
[   12.522928] other info that might help us debug this:
[   12.523984] rcu_scheduler_active = 2, debug_locks = 1
[   12.524855] 5 locks held by kworker/u8:2/152:
[   12.525438]  #0: 00000000057be08c ((wq_completion)phy0){+.+.}, at: process_one_work+0x1a2/0x620
[   12.526607]  #1: 0000000059c6b07a ((work_completion)(&sdata->csa_finalize_work)){+.+.}, at: process_one_work+0x1a2/0x620
[   12.528001]  #2: 00000000f184ba7d (&wdev->mtx){+.+.}, at: ieee80211_csa_finalize_work+0x2f/0x90
[   12.529116]  #3: 00000000831a1f54 (&local->mtx){+.+.}, at: ieee80211_csa_finalize_work+0x47/0x90
[   12.530233]  #4: 00000000fd06f988 (&local->chanctx_mtx){+.+.}, at: ieee80211_csa_finalize_work+0x51/0x90

Signed-off-by: Thomas Pedersen <thomas@eero.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

staging:iio:ad7150: fix threshold mode config bit

[ Upstream commit df4d737ee4d7205aaa6275158aeebff87fd14488 ]

According to the AD7150 configuration register description, bit 7 assumes
value 1 when the threshold mode is fixed and 0 when it is adaptive,
however, the operation that identifies this mode was considering the
opposite values.

This patch renames the boolean variable to describe it correctly and
properly replaces it in the places where it is used.

Fixes: 531efd6aa0991 ("staging:iio:adc:ad7150: chan_spec conv + i2c_smbus commands + drop unused poweroff timeout control.")
Signed-off-by: Melissa Wen <melissa.srw@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

soundwire: stream: fix out of boundary access on port properties

[ Upstream commit 03ecad90d3798be11b033248bbd4bbff4425a1c7 ]

Assigning local iterator to array element and using it again for
indexing would cross the array boundary.
Fix this by directly referring array element without using the local
variable.

Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

bpf: sockmap, fix use after free from sleep in psock backlog workqueue

[ Upstream commit bd95e678e0f6e18351ecdc147ca819145db9ed7b ]

Backlog work for psock (sk_psock_backlog) might sleep while waiting
for memory to free up when sending packets. However, while sleeping
the socket may be closed and removed from the map by the user space
side.

This breaks an assumption in sk_stream_wait_memory, which expects the
wait queue to be still there when it wakes up resulting in a
use-after-free shown below. To fix his mark sendmsg as MSG_DONTWAIT
to avoid the sleep altogether. We already set the flag for the
sendpage case but we missed the case were sendmsg is used.
Sockmap is currently the only user of skb_send_sock_locked() so only
the sockmap paths should be impacted.

==================================================================
BUG: KASAN: use-after-free in remove_wait_queue+0x31/0x70
Write of size 8 at addr ffff888069a0c4e8 by task kworker/0:2/110

CPU: 0 PID: 110 Comm: kworker/0:2 Not tainted 5.0.0-rc2-00335-g28f9d1a3d4fe-dirty #14
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-2.fc27 04/01/2014
Workqueue: events sk_psock_backlog
Call Trace:
 print_address_description+0x6e/0x2b0
 ? remove_wait_queue+0x31/0x70
 kasan_report+0xfd/0x177
 ? remove_wait_queue+0x31/0x70
 ? remove_wait_queue+0x31/0x70
 remove_wait_queue+0x31/0x70
 sk_stream_wait_memory+0x4dd/0x5f0
 ? sk_stream_wait_close+0x1b0/0x1b0
 ? wait_woken+0xc0/0xc0
 ? tcp_current_mss+0xc5/0x110
 tcp_sendmsg_locked+0x634/0x15d0
 ? tcp_set_state+0x2e0/0x2e0
 ? __kasan_slab_free+0x1d1/0x230
 ? kmem_cache_free+0x70/0x140
 ? sk_psock_backlog+0x40c/0x4b0
 ? process_one_work+0x40b/0x660
 ? worker_thread+0x82/0x680
 ? kthread+0x1b9/0x1e0
 ? ret_from_fork+0x1f/0x30
 ? check_preempt_curr+0xaf/0x130
 ? iov_iter_kvec+0x5f/0x70
 ? kernel_sendmsg_locked+0xa0/0xe0
 skb_send_sock_locked+0x273/0x3c0
 ? skb_splice_bits+0x180/0x180
 ? start_thread+0xe0/0xe0
 ? update_min_vruntime.constprop.27+0x88/0xc0
 sk_psock_backlog+0xb3/0x4b0
 ? strscpy+0xbf/0x1e0
 process_one_work+0x40b/0x660
 worker_thread+0x82/0x680
 ? process_one_work+0x660/0x660
 kthread+0x1b9/0x1e0
 ? __kthread_create_on_node+0x250/0x250
 ret_from_fork+0x1f/0x30

Fixes: 20bf50de3028c ("skbuff: Function to send an skbuf on a socket")
Reported-by: Jakub Sitnicki <jakub@cloudflare.com>
Tested-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

mac80211: fix rate reporting inside cfg80211_calculate_bitrate_he()

[ Upstream commit 25d16d124a5e249e947c0487678b61dcff25cf8b ]

The reported rate is not scaled down correctly. After applying this patch,
the function will behave just like the v/ht equivalents.

Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

samples, bpf: suppress compiler warning

[ Upstream commit a195cefff49f60054998333e81ee95170ce8bf92 ]

GCC 9 fails to calculate the size of local constant strings and produces a
false positive:

samples/bpf/task_fd_query_user.c: In function ‘test_debug_fs_uprobe’:
samples/bpf/task_fd_query_user.c:242:67: warning: ‘%s’ directive output may be truncated writing up to 255 bytes into a region of size 215 [-Wformat-truncation=]
  242 |  snprintf(buf, sizeof(buf), "/sys/kernel/debug/tracing/events/%ss/%s/id",
      |                                                                   ^~
  243 |    event_type, event_alias);
      |                ~~~~~~~~~~~
samples/bpf/task_fd_query_user.c:242:2: note: ‘snprintf’ output between 45 and 300 bytes into a destination of size 256
  242 |  snprintf(buf, sizeof(buf), "/sys/kernel/debug/tracing/events/%ss/%s/id",
      |  ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
  243 |    event_type, event_alias);
      |    ~~~~~~~~~~~~~~~~~~~~~~~~

Workaround this by lowering the buffer size to a reasonable value.
Related GCC Bugzilla: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=83431

Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

samples, bpf: fix to change the buffer size for read()

[ Upstream commit f7c2d64bac1be2ff32f8e4f500c6e5429c1003e0 ]

If the trace for read is larger than 4096, the return
value sz will be 4096. This results in off-by-one error
on buf:

    static char buf[4096];
    ssize_t sz;

    sz = read(trace_fd, buf, sizeof(buf));
    if (sz > 0) {
        buf[sz] = 0;
        puts(buf);
    }

Signed-off-by: Chang-Hsien Tsai <luke.tw@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

Input: elantech - enable middle button support on 2 ThinkPads

[ Upstream commit aa440de3058a3ef530851f9ef373fbb5f694dbc3 ]

Adding 2 new touchpad PNPIDs to enable middle button support.

Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

soc: bcm: brcmstb: biuctrl: Register writes require a barrier

[ Upstream commit 6b23af0783a54efb348f0bd781b7850636023dbb ]

The BIUCTRL register writes require that a data barrier be inserted
after comitting the write to the register for the block to latch in the
recently written values. Reads have no such requirement and are not
changed.

Fixes: 34642650e5bc ("soc: Move brcmstb to bcm/brcmstb")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

soc: brcmstb: Fix error path for unsupported CPUs

[ Upstream commit 490cad5a3ad6ef0bfd3168a5063140b982f3b22a ]

In case setup_hifcpubiuctrl_regs() returns an error, because of e.g:
an unsupported CPU type, just catch that error and return instead of
blindly continuing with the initialization. This fixes a NULL pointer
de-reference with the code continuing without having a proper array of
registers to use.

Fixes: 22f7a9116eba ("soc: brcmstb: Correct CPU_CREDIT_REG offset for Brahma-B53 CPUs")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

crypto: talitos - rename alternative AEAD algos.

commit a1a42f84011fae6ff08441a91aefeb7febc984fc upstream.

The talitos driver has two ways to perform AEAD depending on the
HW capability. Some HW support both. It is needed to give them
different names to distingish which one it is for instance when
a test fails.

Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Fixes: 7405c8d7ff97 ("crypto: talitos - templates for AEAD using HMAC_SNOOP_NO_AFEU")
Cc: stable@vger.kernel.org
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Linux 4.19.58

dmaengine: imx-sdma: remove BD_INTR for channel0

commit 3f93a4f297961c12bb17aa16cb3a4d1291823cae upstream.

It is possible for an irq triggered by channel0 to be received later
after clks are disabled once firmware loaded during sdma probe. If
that happens then clearing them by writing to SDMA_H_INTR won't work
and the kernel will hang processing infinite interrupts. Actually,
don't need interrupt triggered on channel0 since it's pollling
SDMA_H_STATSTOP to know channel0 done rather than interrupt in
current code, just clear BD_INTR to disable channel0 interrupt to
avoid the above case.
This issue was brought by commit 1d069bfa3c78 ("dmaengine: imx-sdma:
ack channel 0 IRQ in the interrupt handler") which didn't take care
the above case.

Fixes: 1d069bfa3c78 ("dmaengine: imx-sdma: ack channel 0 IRQ in the interrupt handler")
Cc: stable@vger.kernel.org #5.0+
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Reported-by: Sven Van Asbroeck <thesven73@gmail.com>
Tested-by: Sven Van Asbroeck <thesven73@gmail.com>
Reviewed-by: Michael Olbrich <m.olbrich@pengutronix.de>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dmaengine: qcom: bam_dma: Fix completed descriptors count

commit f6034225442c4a87906d36e975fd9e99a8f95487 upstream.

One space is left unused in circular FIFO to differentiate
'full' and 'empty' cases. So take that in to account while
counting for the descriptors completed.

Fixes the issue reported here,
https://lkml.org/lkml/2019/6/18/669

Cc: stable@vger.kernel.org
Reported-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

MIPS: have "plain" make calls build dtbs for selected platforms

commit 637dfa0fad6d91a9a709dc70549a6d20fa77f615 upstream.

scripts/package/builddeb calls "make dtbs_install" after executing
a plain make (i.e. no build targets specified). It will fail if dtbs
were not built beforehand. Match the arm64 architecture where DTBs get
built by the "all" target.

Signed-off-by: Cedric Hombourger <Cedric_Hombourger@mentor.com>
[paul.burton@mips.com: s/builddep/builddeb]
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org
Cc: stable@vger.kernel.org # v4.1+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

MIPS: Add missing EHB in mtc0 -> mfc0 sequence.

commit 0b24cae4d535045f4c9e177aa228d4e97bad212c upstream.

Add a missing EHB (Execution Hazard Barrier) in mtc0 -> mfc0 sequence.
Without this execution hazard barrier it's possible for the value read
back from the KScratch register to be the value from before the mtc0.

Reproducible on P5600 & P6600.

The hazard is documented in the MIPS Architecture Reference Manual Vol.
III: MIPS32/microMIPS32 Privileged Resource Architecture (MD00088), rev
6.03 table 8.1 which includes:

   Producer | Consumer | Hazard
  ----------|----------|----------------------------
   mtc0     | mfc0     | any coprocessor 0 register

Signed-off-by: Dmitry Korotin <dkorotin@wavecomp.com>
[paul.burton@mips.com:
  - Commit message tweaks.
  - Add Fixes tags.
  - Mark for stable back to v3.15 where P5600 support was introduced.]
Signed-off-by: Paul Burton <paul.burton@mips.com>
Fixes: 3d8bfdd03072 ("MIPS: Use C0_KScratch (if present) to hold PGD pointer.")
Fixes: 829dcc0a956a ("MIPS: Add MIPS P5600 probe support")
Cc: linux-mips@vger.kernel.org
Cc: stable@vger.kernel.org # v3.15+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

MIPS: Fix bounds check virt_addr_valid

commit d6ed083f5cc621e15c15b56c3b585fd524dbcb0f upstream.

The bounds check used the uninitialized variable vaddr, it should use
the given parameter kaddr instead. When using the uninitialized value
the compiler assumed it to be 0 and optimized this function to just
return 0 in all cases.

This should make the function check the range of the given address and
only do the page map check in case it is in the expected range of
virtual addresses.

Fixes: 074a1e1167af ("MIPS: Bounds check virt_addr_valid")
Cc: stable@vger.kernel.org # v4.12+
Cc: Paul Burton <paul.burton@mips.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: ralf@linux-mips.org
Cc: jhogan@kernel.org
Cc: f4bug@amsat.org
Cc: linux-mips@vger.kernel.org
Cc: ysu@wavecomp.com
Cc: jcristau@debian.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

svcrdma: Ignore source port when computing DRC hash

commit 1e091c3bbf51d34d5d96337a59ce5ab2ac3ba2cc upstream.

The DRC appears to be effectively empty after an RPC/RDMA transport
reconnect. The problem is that each connection uses a different
source port, which defeats the DRC hash.

Clients always have to disconnect before they send retransmissions
to reset the connection's credit accounting, thus every retransmit
on NFS/RDMA will miss the DRC.

An NFS/RDMA client's IP source port is meaningless for RDMA
transports. The transport layer typically sets the source port value
on the connection to a random ephemeral port. The server already
ignores it for the "secure port" check. See commit 16e4d93f6de7
("NFSD: Ignore client's source port on RDMA transports").

The Linux NFS server's DRC resolves XID collisions from the same
source IP address by using the checksum of the first 200 bytes of
the RPC call header.

Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Cc: stable@vger.kernel.org # v4.14+
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

nfsd: Fix overflow causing non-working mounts on 1 TB machines

commit 3b2d4dcf71c4a91b420f835e52ddea8192300a3b upstream.

Since commit 10a68cdf10 (nfsd: fix performance-limiting session
calculation) (Linux 5.1-rc1 and 4.19.31), shares from NFS servers with
1 TB of memory cannot be mounted anymore. The mount just hangs on the
client.

The gist of commit 10a68cdf10 is the change below.

    -avail = clamp_t(int, avail, slotsize, avail/3);
    +avail = clamp_t(int, avail, slotsize, total_avail/3);

Here are the macros.

    #define min_t(type, x, y)       __careful_cmp((type)(x), (type)(y), <)
    #define clamp_t(type, val, lo, hi) min_t(type, max_t(type, val, lo), hi)

`total_avail` is 8,434,659,328 on the 1 TB machine. `clamp_t()` casts
the values to `int`, which for 32-bit integers can only hold values
−2,147,483,648 (−2^31) through 2,147,483,647 (2^31 − 1).

`avail` (in the function signature) is just 65536, so that no overflow
was happening. Before the commit the assignment would result in 21845,
and `num = 4`.

When using `total_avail`, it is causing the assignment to be
18446744072226137429 (printed as %lu), and `num` is then 4164608182.

My next guess is, that `nfsd_drc_mem_used` is then exceeded, and the
server thinks there is no memory available any more for this client.

Updating the arguments of `clamp_t()` and `min_t()` to `unsigned long`
fixes the issue.

Now, `avail = 65536` (before commit 10a68cdf10 `avail = 21845`), but
`num = 4` remains the same.

Fixes: c54f24e338ed (nfsd: fix performance-limiting session calculation)
Cc: stable@vger.kernel.org
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

KVM: LAPIC: Fix pending interrupt in IRR blocked by software disable LAPIC

commit bb34e690e9340bc155ebed5a3d75fc63ff69e082 upstream.

Thomas reported that:

 | Background:
 |
 |    In preparation of supporting IPI shorthands I changed the CPU offline
 |    code to software disable the local APIC instead of just masking it.
 |    That's done by clearing the APIC_SPIV_APIC_ENABLED bit in the APIC_SPIV
 |    register.
 |
 | Failure:
 |
 |    When the CPU comes back online the startup code triggers occasionally
 |    the warning in apic_pending_intr_clear(). That complains that the IRRs
 |    are not empty.
 |
 |    The offending vector is the local APIC timer vector who's IRR bit is set
 |    and stays set.
 |
 | It took me quite some time to reproduce the issue locally, but now I can
 | see what happens.
 |
 | It requires apicv_enabled=0, i.e. full apic emulation. With apicv_enabled=1
 | (and hardware support) it behaves correctly.
 |
 | Here is the series of events:
 |
 |     Guest CPU
 |
 |     goes down
 |
 |       native_cpu_disable()
 |
 |  apic_soft_disable();
 |
 |     play_dead()
 |
 |     ....
 |
 |     startup()
 |
 |       if (apic_enabled())
 |         apic_pending_intr_clear() <- Not taken
 |
 |      enable APIC
 |
 |         apic_pending_intr_clear() <- Triggers warning because IRR is stale
 |
 | When this happens then the deadline timer or the regular APIC timer -
 | happens with both, has fired shortly before the APIC is disabled, but the
 | interrupt was not serviced because the guest CPU was in an interrupt
 | disabled region at that point.
 |
 | The state of the timer vector ISR/IRR bits:
 |
 |                            ISR     IRR
 | before apic_soft_disable()    0       1
 | after apic_soft_disable()     0       1
 |
 | On startup         0       1
 |
 | Now one would assume that the IRR is cleared after the INIT reset, but this
 | happens only on CPU0.
 |
 | Why?
 |
 | Because our CPU0 hotplug is just for testing to make sure nothing breaks
 | and goes through an NMI wakeup vehicle because INIT would send it through
 | the boots-trap code which is not really working if that CPU was not
 | physically unplugged.
 |
 | Now looking at a real world APIC the situation in that case is:
 |
 |                           ISR     IRR
 | before apic_soft_disable()    0       1
 | after apic_soft_disable()     0       1
 |
 | On startup         0       0
 |
 | Why?
 |
 | Once the dying CPU reenables interrupts the pending interrupt gets
 | delivered as a spurious interupt and then the state is clear.
 |
 | While that CPU0 hotplug test case is surely an esoteric issue, the APIC
 | emulation is still wrong, Even if the play_dead() code would not enable
 | interrupts then the pending IRR bit would turn into an ISR .. interrupt
 | when the APIC is reenabled on startup.

From SDM 10.4.7.2 Local APIC State After It Has Been Software Disabled
* Pending interrupts in the IRR and ISR registers are held and require
  masking or handling by the CPU.

In Thomas's testing, hardware cpu will not respect soft disable LAPIC
when IRR has already been set or APICv posted-interrupt is in flight,
so we can skip soft disable APIC checking when clearing IRR and set ISR,
continue to respect soft disable APIC when attempting to set IRR.

Reported-by: Rong Chen <rong.a.chen@intel.com>
Reported-by: Feng Tang <feng.tang@intel.com>
Reported-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Rong Chen <rong.a.chen@intel.com>
Cc: Feng Tang <feng.tang@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Wanpeng Li <wanpengli@tencent.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

KVM: x86: degrade WARN to pr_warn_ratelimited

commit 3f16a5c318392cbb5a0c7a3d19dff8c8ef3c38ee upstream.

This warning can be triggered easily by userspace, so it should certainly not
cause a panic if panic_on_warn is set.

Reported-by: syzbot+c03f30b4f4c46bdf8575@syzkaller.appspotmail.com
Suggested-by: Alexander Potapenko <glider@google.com>
Acked-by: Alexander Potapenko <glider@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

netfilter: ipv6: nf_defrag: accept duplicate fragments again

[ Upstream commit 8a3dca632538c550930ce8bafa8c906b130d35cf ]

When fixing the skb leak introduced by the conversion to rbtree, I
forgot about the special case of duplicate fragments. The condition
under the 'insert_error' label isn't effective anymore as
nf_ct_frg6_gather() doesn't override the returned value anymore. So
duplicate fragments now get NF_DROP verdict.

To accept duplicate fragments again, handle them specially as soon as
inet_frag_queue_insert() reports them. Return -EINPROGRESS which will
translate to NF_STOLEN verdict, like any accepted fragment. However,
such packets don't carry any new information and aren't queued, so we
just drop them immediately.

Fixes: a0d56cb911ca ("netfilter: ipv6: nf_defrag: fix leakage of unqueued fragments")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

bpf: fix bpf_jit_limit knob for PAGE_SIZE >= 64K

[ Upstream commit fdadd04931c2d7cd294dc5b2b342863f94be53a3 ]

Michael and Sandipan report:

  Commit ede95a63b5 introduced a bpf_jit_limit tuneable to limit BPF
  JIT allocations. At compile time it defaults to PAGE_SIZE * 40000,
  and is adjusted again at init time if MODULES_VADDR is defined.

  For ppc64 kernels, MODULES_VADDR isn't defined, so we're stuck with
  the compile-time default at boot-time, which is 0x9c400000 when
  using 64K page size. This overflows the signed 32-bit bpf_jit_limit
  value:

  root@ubuntu:/tmp# cat /proc/sys/net/core/bpf_jit_limit
  -1673527296

  and can cause various unexpected failures throughout the network
  stack. In one case `strace dhclient eth0` reported:

  setsockopt(5, SOL_SOCKET, SO_ATTACH_FILTER, {len=11, filter=0x105dd27f8},
             16) = -1 ENOTSUPP (Unknown error 524)

  and similar failures can be seen with tools like tcpdump. This doesn't
  always reproduce however, and I'm not sure why. The more consistent
  failure I've seen is an Ubuntu 18.04 KVM guest booted on a POWER9
  host would time out on systemd/netplan configuring a virtio-net NIC
  with no noticeable errors in the logs.

Given this and also given that in near future some architectures like
arm64 will have a custom area for BPF JIT image allocations we should
get rid of the BPF_JIT_LIMIT_DEFAULT fallback / default entirely. For
4.21, we have an overridable bpf_jit_alloc_exec(), bpf_jit_free_exec()
so therefore add another overridable bpf_jit_alloc_exec_limit() helper
function which returns the possible size of the memory area for deriving
the default heuristic in bpf_jit_charge_init().

Like bpf_jit_alloc_exec() and bpf_jit_free_exec(), the new
bpf_jit_alloc_exec_limit() assumes that module_alloc() is the default
JIT memory provider, and therefore in case archs implement their custom
module_alloc() we use MODULES_{END,_VADDR} for limits and otherwise for
vmalloc_exec() cases like on ppc64 we use VMALLOC_{END,_START}.

Additionally, for archs supporting large page sizes, we should change
the sysctl to be handled as long to not run into sysctl restrictions
in future.

Fixes: ede95a63b5e8 ("bpf: add bpf_jit_limit knob to restrict unpriv allocations")
Reported-by: Sandipan Das <sandipan@linux.ibm.com>
Reported-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: hns: fix unsigned comparison to less than zero

[ Upstream commit ea401685a20b5d631957f024bda86e1f6118eb20 ]

Currently mskid is unsigned and hence comparisons with negative
error return values are always false. Fix this by making mskid an
int.

Fixes: f058e46855dc ("net: hns: fix ICMP6 neighbor solicitation messages discard problem")
Addresses-Coverity: ("Operands don't affect result")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

sc16is7xx: move label 'err_spi' to correct section

[ Upstream commit e00164a0f000de893944981f41a568c981aca658 ]

err_spi is used when SERIAL_SC16IS7XX_SPI is enabled, so make
the label only available under SERIAL_SC16IS7XX_SPI option.
Otherwise, the below warning appears.

drivers/tty/serial/sc16is7xx.c:1523:1: warning: label ‘err_spi’ defined but not used [-Wunused-label]
 err_spi:
  ^~~~~~~

Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Fixes: ac0cdb3d9901 ("sc16is7xx: missing unregister/delete driver on error in sc16is7xx_init()")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

netfilter: ipv6: nf_defrag: fix leakage of unqueued fragments

[ Upstream commit a0d56cb911ca301de81735f1d73c2aab424654ba ]

With commit 997dd9647164 ("net: IP6 defrag: use rbtrees in
nf_conntrack_reasm.c"), nf_ct_frag6_reasm() is now called from
nf_ct_frag6_queue(). With this change, nf_ct_frag6_queue() can fail
after the skb has been added to the fragment queue and
nf_ct_frag6_gather() was adapted to handle this case.

But nf_ct_frag6_queue() can still fail before the fragment has been
queued. nf_ct_frag6_gather() can't handle this case anymore, because it
has no way to know if nf_ct_frag6_queue() queued the fragment before
failing. If it didn't, the skb is lost as the error code is overwritten
with -EINPROGRESS.

Fix this by setting -EINPROGRESS directly in nf_ct_frag6_queue(), so
that nf_ct_frag6_gather() can propagate the error as is.

Fixes: 997dd9647164 ("net: IP6 defrag: use rbtrees in nf_conntrack_reasm.c")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ip6: fix skb leak in ip6frag_expire_frag_queue()

[ Upstream commit 47d3d7fdb10a21c223036b58bd70ffdc24a472c4 ]

Since ip6frag_expire_frag_queue() now pulls the head skb
from frag queue, we should no longer use skb_get(), since
this leads to an skb leak.

Stefan Bader initially reported a problem in 4.4.stable [1] caused
by the skb_get(), so this patch should also fix this issue.

296583.091021] kernel BUG at /build/linux-6VmqmP/linux-4.4.0/net/core/skbuff.c:1207!
[296583.091734] Call Trace:
[296583.091749]  [<ffffffff81740e50>] __pskb_pull_tail+0x50/0x350
[296583.091764]  [<ffffffff8183939a>] _decode_session6+0x26a/0x400
[296583.091779]  [<ffffffff817ec719>] __xfrm_decode_session+0x39/0x50
[296583.091795]  [<ffffffff818239d0>] icmpv6_route_lookup+0xf0/0x1c0
[296583.091809]  [<ffffffff81824421>] icmp6_send+0x5e1/0x940
[296583.091823]  [<ffffffff81753238>] ? __netif_receive_skb+0x18/0x60
[296583.091838]  [<ffffffff817532b2>] ? netif_receive_skb_internal+0x32/0xa0
[296583.091858]  [<ffffffffc0199f74>] ? ixgbe_clean_rx_irq+0x594/0xac0 [ixgbe]
[296583.091876]  [<ffffffffc04eb260>] ? nf_ct_net_exit+0x50/0x50 [nf_defrag_ipv6]
[296583.091893]  [<ffffffff8183d431>] icmpv6_send+0x21/0x30
[296583.091906]  [<ffffffff8182b500>] ip6_expire_frag_queue+0xe0/0x120
[296583.091921]  [<ffffffffc04eb27f>] nf_ct_frag6_expire+0x1f/0x30 [nf_defrag_ipv6]
[296583.091938]  [<ffffffff810f3b57>] call_timer_fn+0x37/0x140
[296583.091951]  [<ffffffffc04eb260>] ? nf_ct_net_exit+0x50/0x50 [nf_defrag_ipv6]
[296583.091968]  [<ffffffff810f5464>] run_timer_softirq+0x234/0x330
[296583.091982]  [<ffffffff8108a339>] __do_softirq+0x109/0x2b0

Fixes: d4289fcc9b16 ("net: IP6 defrag: use rbtrees for IPv6 defrag")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Stefan Bader <stefan.bader@canonical.com>
Cc: Peter Oskolkov <posk@google.com>
Cc: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

rds: Fix warning.

[ Upstream commit d84e7bc0595a7e146ad0ddb80b240cea77825245 ]

>> net/rds/send.c:1109:42: warning: Using plain integer as NULL pointer

Fixes: ea010070d0a7 ("net/rds: fix warn in rds_message_alloc_sgs")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ALSA: hda: Initialize power_state field properly

[ Upstream commit 183ab39eb0ea9879bb68422a83e65f750f3192f0 ]

The recent commit 98081ca62cba ("ALSA: hda - Record the current power
state before suspend/resume calls") made the HD-audio driver to store
the PM state in power_state field.  This forgot, however, the
initialization at power up.  Although the codec drivers usually don't
need to refer to this field in the normal operation, let's initialize
it properly for consistency.

Fixes: 98081ca62cba ("ALSA: hda - Record the current power state before suspend/resume calls")
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: hns: Fixes the missing put_device in positive leg for roce reset

[ Upstream commit 4d96e13ee9cd1f7f801e8c7f4b12f09d1da4a5d8 ]

This patch fixes the missing device reference release-after-use in
the positive leg of the roce reset API of the HNS DSAF.

Fixes: c969c6e7ab8c ("net: hns: Fix object reference leaks in hns_dsaf_roce_reset()")
Reported-by: John Garry <john.garry@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

x86/boot/compressed/64: Do not corrupt EDX on EFER.LME=1 setting

[ Upstream commit 45b13b424faafb81c8c44541f093a682fdabdefc ]

RDMSR in the trampoline code overwrites EDX but that register is used
to indicate whether 5-level paging has to be enabled and if clobbered,
leads to failure to boot on a 5-level paging machine.

Preserve EDX on the stack while we are dealing with EFER.

Fixes: b677dfae5aa1 ("x86/boot/compressed/64: Set EFER.LME=1 in 32-bit trampoline before returning to long mode")
Reported-by: Kyle D Pelton <kyle.d.pelton@intel.com>
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: dave.hansen@linux.intel.com
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Wei Huang <wei@redhat.com>
Cc: x86-ml <x86@kernel.org>
Link: https://lkml.kernel.org/r/20190206115253.1907-1-kirill.shutemov@linux.intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

selftests: fib_rule_tests: Fix icmp proto with ipv6

[ Upstream commit 15d55bae4e3c43cd9f87fd93c73a263e172d34e1 ]

A recent commit returns an error if icmp is used as the ip-proto for
IPv6 fib rules. Update fib_rule_tests to send ipv6-icmp instead of icmp.

Fixes: 5e1a99eae8499 ("ipv4: Add ICMPv6 support when parse route ipproto")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

scsi: tcmu: fix use after free

[ Upstream commit 40d883b091758472c79b81fa1c0e0347e24a9cff ]

Fixes: a94a2572b977 ("scsi: tcmu: avoid cmd/qfull timers updated whenever a new cmd comes")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Mike Christie <mchristi@redhat.com>
Signed-off-by: Xiubo Li <xiubli@redhat.com>
Reviewed-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

mac80211: mesh: fix missing unlock on error in table_path_del()

[ Upstream commit f2ffff085d287eec499f1fccd682796ad8010303 ]

spin_lock_bh() is used in table_path_del() but rcu_read_unlock()
is used for unlocking. Fix it by using spin_unlock_bh() instead
of rcu_read_unlock() in the error handling case.

Fixes: b4c3fbe63601 ("mac80211: Use linked list instead of rhashtable walk for mesh tables")
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

f2fs: don't access node/meta inode mapping after iput

[ Upstream commit 7c77bf7de1574ac7a31a2b76f4927404307d13e7 ]

This fixes wrong access of address spaces of node and meta inodes after iput.

Fixes: 60aa4d5536ab ("f2fs: fix use-after-free issue when accessing sbi->stat_info")
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/fb-helper: generic: Don't take module ref for fbcon

[ Upstream commit 6ab20a05f4c7ed45632e24d5397d6284e192567d ]

It's now safe to let fbcon unbind automatically on fbdev unregister.
The crash problem was fixed in commit 2122b40580dd
("fbdev: fbcon: Fix unregister crash when more than one framebuffer")

Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20190210131039.52664-13-noralf@tronnes.org
Signed-off-by: Sasha Levin <sashal@kernel.org>

media: s5p-mfc: fix incorrect bus assignment in virtual child device

[ Upstream commit 1e0d0a5fd38192f23304ea2fc2b531fea7c74247 ]

Virtual MFC codec's child devices must not be assigned to platform bus,
because they are allocated as raw 'struct device' and don't have the
corresponding 'platform' part. This fixes NULL pointer access revealed
recently by commit a66d972465d1 ("devres: Align data[] to
ARCH_KMALLOC_MINALIGN").

Fixes: c79667dd93b0 ("media: s5p-mfc: replace custom reserved memory handling code with generic one")

Reported-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net/smc: move unhash before release of clcsock

[ Upstream commit f61bca58f6c36e666c2b807697f25e5e98708162 ]

Commit <26d92e951fe0>
("net/smc: move unhash as early as possible in smc_release()")
fixes one occurrence in the smc code, but the same pattern exists
in other places. This patch covers the remaining occurrences and
makes sure, the unhash operation is done before the smc->clcsock is
released. This avoids a potential use-after-free in smc_diag_dump().

Reviewed-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

mlxsw: spectrum: Handle VLAN device unlinking

[ Upstream commit e149113a74c35f0a28d1bfe17d2505a03563c1d5 ]

In commit 993107fea5ee ("mlxsw: spectrum_switchdev: Fix VLAN device
deletion via ioctl") I fixed a bug caused by the fact that the driver
views differently the deletion of a VLAN device when it is deleted via
an ioctl and netlink.

Instead of relying on a specific order of events (device being
unregistered vs. VLAN filter being updated), simply make sure that the
driver performs the necessary cleanup when the VLAN device is unlinked,
which always happens before the other two events.

Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

tty: rocket: fix incorrect forward declaration of 'rp_init()'

[ Upstream commit 423ea3255424b954947d167681b71ded1b8fca53 ]

Make the forward declaration actually match the real function
definition, something that previous versions of gcc had just ignored.

This is another patch to fix new warnings from gcc-9 before I start the
merge window pulls.  I don't want to miss legitimate new warnings just
because my system update brought a new compiler with new warnings.

Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

btrfs: Ensure replaced device doesn't have pending chunk allocation

commit debd1c065d2037919a7da67baf55cc683fee09f0 upstream.

Recent FITRIM work, namely bbbf7243d62d ("btrfs: combine device update
operations during transaction commit") combined the way certain
operations are recoded in a transaction. As a result an ASSERT was added
in dev_replace_finish to ensure the new code works correctly.
Unfortunately I got reports that it's possible to trigger the assert,
meaning that during a device replace it's possible to have an unfinished
chunk allocation on the source device.

This is supposed to be prevented by the fact that a transaction is
committed before finishing the replace oepration and alter acquiring the
chunk mutex. This is not sufficient since by the time the transaction is
committed and the chunk mutex acquired it's possible to allocate a chunk
depending on the workload being executed on the replaced device. This
bug has been present ever since device replace was introduced but there
was never code which checks for it.

The correct way to fix is to ensure that there is no pending device
modification operation when the chunk mutex is acquire and if there is
repeat transaction commit. Unfortunately it's not possible to just
exclude the source device from btrfs_fs_devices::dev_alloc_list since
this causes ENOSPC to be hit in transaction commit.

Fixing that in another way would need to add special cases to handle the
last writes and forbid new ones. The looped transaction fix is more
obvious, and can be easily backported. The runtime of dev-replace is
long so there's no noticeable delay caused by that.

Reported-by: David Sterba <dsterba@suse.com>
Fixes: 391cd9df81ac ("Btrfs: fix unprotected alloc list insertion during the finishing procedure of replace")
CC: stable@vger.kernel.org # 4.4+
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>