Jean-Baptiste Maneyrol [Thu, 27 Jun 2019 13:19:53 +0000 (13:19 +0000)]
iio: imu: mpu6050: add missing available scan masks
Driver only supports 3-axis gyro and/or 3-axis accel.
For icm20602, temp data is mandatory for all configurations.
Fix all single and double axis configurations (almost never used) and more
importantly fix 3-axis gyro and 6-axis accel+gyro buffer on icm20602 when
temp data is not enabled.
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Fixes:
1615fe41a195 ("iio: imu: mpu6050: Fix FIFO layout for ICM20602")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Gwendal Grignou [Fri, 28 Jun 2019 19:17:09 +0000 (12:17 -0700)]
iio: cros_ec_accel_legacy: Fix incorrect channel setting
INFO_SCALE is set both for each channel and all channels.
iio is using all channel setting, so the error was not user visible.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Maarten ter Huurne [Thu, 4 Jul 2019 17:36:56 +0000 (19:36 +0200)]
IIO: Ingenic JZ47xx: Set clock divider on probe
The SADC component can run at up to 8 MHz on JZ4725B, but is fed
a 12 MHz input clock (EXT). Divide it by two to get 6 MHz, then
set up another divider to match, to produce a 10us clock.
If the clock dividers are left on their power-on defaults (a divider
of 1), the SADC mostly works, but will occasionally produce erroneous
readings. This led to button presses being detected out of nowhere on
the RS90 every few minutes. With this change, no ghost button presses
were logged in almost a day worth of testing.
The ADCLK register for configuring clock dividers doesn't exist on
JZ4740, so avoid writing it there.
A function has been introduced rather than a flag because there is a lot
of variation between the ADCLK registers on JZ47xx SoCs, both in
the internal layout of the register and in the frequency range
supported by the SADC. So this solution should make it easier
to add support for other JZ47xx SoCs later.
Fixes:
1a78daea107d ("iio: adc: probe should set clock divider")
Signed-off-by: Maarten ter Huurne <maarten@treewalker.org>
Signed-off-by: Artur Rojek <contact@artur-rojek.eu>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Joe Perches [Wed, 10 Jul 2019 05:04:17 +0000 (22:04 -0700)]
iio: adc: max9611: Fix misuse of GENMASK macro
Arguments are supposed to be ordered high then low.
Signed-off-by: Joe Perches <joe@perches.com>
Fixes:
69780a3bbc0b ("iio: adc: Add Maxim max9611 ADC driver")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Linus Torvalds [Fri, 12 Jul 2019 01:45:29 +0000 (18:45 -0700)]
Merge tag 'tag-chrome-platform-for-v5.3' of git://git./linux/kernel/git/chrome-platform/linux
Pull chrome platform updates from Benson Leung
"CrOS EC:
- Add new CrOS ISHTP transport protocol
- Add proper documentation for debugfs entries and expose resume and
uptime files
- Select LPC transport protocol variant at runtime.
- Add lid angle sensor driver
- Fix oops on suspend/resume for lightbar driver
- Set CrOS SPI transport protol in realtime
Wilco EC:
- Add telemetry char device interface
- Add support for event handling
- Add new sysfs attributes
Misc:
- Contains ib-mfd-cros-v5.3 immutable branch from mfd, with
cros_ec_commands.h header freshly synced with Chrome OS's EC
project"
* tag 'tag-chrome-platform-for-v5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux: (54 commits)
mfd / platform: cros_ec_debugfs: Expose resume result via debugfs
platform/chrome: lightbar: Get drvdata from parent in suspend/resume
iio: cros_ec: Add lid angle driver
platform/chrome: wilco_ec: Add circular buffer as event queue
platform/chrome: cros_ec_lpc_mec: Fix kernel-doc comment first line
platform/chrome: cros_ec_lpc: Choose Microchip EC at runtime
platform/chrome: cros_ec_lpc: Merge cros_ec_lpc and cros_ec_lpc_reg
Input: cros_ec_keyb: mask out extra flags in event_type
platform/chrome: wilco_ec: Fix unreleased lock in event_read()
platform/chrome: cros_ec_debugfs: cros_ec_uptime_fops can be static
platform/chrome: cros_ec_debugfs: Add debugfs ABI documentation
platform/chrome: cros_ec_debugfs: Fix kernel-doc comment first line
platform/chrome: cros_ec_debugfs: Add debugfs entry to retrieve EC uptime
mfd: cros_ec: Update I2S API
mfd: cros_ec: Add Management API entry points
mfd: cros_ec: Add SKU ID and Secure storage API
mfd: cros_ec: Add API for rwsig
mfd: cros_ec: Add API for Fingerprint support
mfd: cros_ec: Add API for Touchpad support
mfd: cros_ec: Add API for EC-EC communication
...
Linus Torvalds [Fri, 12 Jul 2019 01:35:30 +0000 (18:35 -0700)]
Merge tag 'devicetree-for-5.3' of git://git./linux/kernel/git/robh/linux
Pull Devicetree updates from Rob Herring:
- DT binding schema examples are now validated against the schemas.
Various examples are fixed due to that.
- Sync dtc with upstream version v1.5.0-30-g702c1b6c0e73
- Initial schemas for networking bindings. This includes ethernet, phy
and mdio common bindings with several Allwinner and stmmac converted
to the schema.
- Conversion of more Arm top-level SoC/board bindings to DT schema
- Conversion of PSCI binding to DT schema
- Rework Arm CPU schema to coexist with other CPU schemas
- Add a bunch of missing vendor prefixes and new ones for SoChip,
Sipeed, Kontron, B&R Industrial Automation GmbH, and Espressif
- Add Mediatek UART RX wakeup support to binding
- Add reset to ST UART binding
- Remove some Linuxisms from the endianness common-properties.txt
binding
- Make the flattened DT read-only after init
- Ignore disabled reserved memory nodes
- Clean-up some dead code in FDT functions
* tag 'devicetree-for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (56 commits)
dt-bindings: vendor-prefixes: add Sipeed
dt-bindings: vendor-prefixes: add SoChip
dt-bindings: 83xx-512x-pci: Drop cell-index property
dt-bindings: serial: add documentation for Rx in-band wakeup support
dt-bindings: arm: Convert RDA Micro board/soc bindings to json-schema
of: unittest: simplify getting the adapter of a client
of/fdt: pass early_init_dt_reserve_memory_arch() with bool type nomap
of/platform: Drop superfluous cast in of_device_make_bus_id()
dt-bindings: usb: ehci: Fix example warnings
dt-bindings: net: Use phy-mode instead of phy-connection-type
dt-bindings: simple-framebuffer: Add requirement for pipelines
dt-bindings: display: Fix simple-framebuffer example
dt-bindings: net: mdio: Add child nodes
dt-bindings: net: mdio: Add address and size cells
dt-bindings: net: mdio: Add a nodename pattern
dt-bindings: mtd: sunxi-nand: Drop 'maxItems' from child 'reg' property
dt-bindings: arm: Limit cpus schema to only check Arm 'cpu' nodes
dt-bindings: backlight: lm3630a: correct schema validation
dt-bindings: net: dwmac: Deprecate the PHY reset properties
dt-bindings: net: sun8i-emac: Convert the binding to a schemas
...
Linus Torvalds [Fri, 12 Jul 2019 01:11:21 +0000 (18:11 -0700)]
Merge tag 'mmc-v5.3' of git://git./linux/kernel/git/ulfh/mmc
Pull MMC updates from Ulf Hansson:
"MMC core:
- Let the dma map ops deal with bouncing and drop dma_max_pfn() from
the dma-mapping interface for ARM
- Convert the generic MMC DT doc to YAML schemas
- Drop questionable support for powered-on re-init of SDIO cards at
runtime resume and for SDIO HW reset
- Prevent questionable re-init of powered-on removable SDIO cards at
system resume
- Cleanup and clarify some SDIO core code
MMC host:
- tmio: Make runtime PM enablement more flexible for variants
- tmio/renesas_sdhi: Rename DT doc tmio_mmc.txt to renesas,sdhi.txt
to clarify
- sdhci-pci: Add support for Intel EHL
- sdhci-pci-o2micro: Enable support for 8-bit bus
- sdhci-msm: Prevent acquiring a mutex while holding a spin_lock
- sdhci-of-esdhc: Improve clock management and tuning
- sdhci_am654: Enable support for 4 and 8-bit bus on J721E
- sdhci-sprd: Use pinctrl for a proper signal voltage switch
- sdhci-sprd: Add support for HS400 enhanced strobe mode
- sdhci-sprd: Enable PHY DLL and allow delay config to stabilize the
clock
- sdhci-sprd: Add support for optional gate clock
- sunxi-mmc: Convert DT doc to YAML schemas
- meson-gx: Add support for broken DRAM access for DMA
MEMSTICK core:
- Fixup error path of memstick_init()"
* tag 'mmc-v5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (52 commits)
mmc: sdhci_am654: Add dependency on MMC_SDHCI_AM654
mmc: alcor: remove a redundant greater or equal to zero comparison
mmc: sdhci-msm: fix mutex while in spinlock
mmc: sdhci_am654: Make some symbols static
dma-mapping: remove dma_max_pfn
mmc: core: let the dma map ops handle bouncing
dt-binding: mmc: rename tmio_mmc.txt to renesas,sdhi.txt
mmc: sdhci-sprd: Add pin control support for voltage switch
dt-bindings: mmc: sprd: Add pinctrl support
mmc: sdhci-sprd: Add start_signal_voltage_switch ops
mmc: sdhci-pci: Add support for Intel EHL
mmc: tmio: Use dma_max_mapping_size() instead of a workaround
mmc: sdio: Drop unused in-parameter from mmc_sdio_init_card()
mmc: sdio: Drop unused in-parameter to mmc_sdio_reinit_card()
mmc: sdio: Don't re-initialize powered-on removable SDIO cards at resume
mmc: sdio: Drop powered-on re-init at runtime resume and HW reset
mmc: sdio: Move comment about re-initialization to mmc_sdio_reinit_card()
mmc: sdio: Drop mmc_claim|release_host() in mmc_sdio_power_restore()
mmc: sdio: Turn sdio_run_irqs() into static
mmc: sdhci: Fix indenting on SDHCI_CTRL_8BITBUS
...
Linus Torvalds [Thu, 11 Jul 2019 22:40:06 +0000 (15:40 -0700)]
Merge tag 'usb-5.3-rc1' of git://git./linux/kernel/git/gregkh/usb
Pull USB / PHY updates from Greg KH:
"Here is the big USB and PHY driver pull request for 5.3-rc1.
Lots of stuff here, all of which has been in linux-next for a while
with no reported issues. Nothing is earth-shattering, just constant
forward progress for more devices supported and cleanups and small
fixes:
- USB gadget driver updates and fixes
- new USB gadget driver for some hardware, followed by a quick revert
of those patches as they were not ready to be merged...
- PHY driver updates
- Lots of new driver additions and cleanups with a few fixes mixed
in"
* tag 'usb-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (145 commits)
Revert "usb: gadget: storage: Remove warning message"
Revert "dt-bindings: add binding for USBSS-DRD controller."
Revert "usb:gadget Separated decoding functions from dwc3 driver."
Revert "usb:gadget Patch simplify usb_decode_set_clear_feature function."
Revert "usb:gadget Simplify usb_decode_get_set_descriptor function."
Revert "usb:cdns3 Add Cadence USB3 DRD Driver"
Revert "usb:cdns3 Fix for stuck packets in on-chip OUT buffer."
usb :fsl: Change string format for errata property
usb: host: Stops USB controller init if PLL fails to lock
usb: linux/fsl_device: Add platform member has_fsl_erratum_a006918
usb: phy: Workaround for USB erratum-A005728
usb: fsl: Set USB_EN bit to select ULPI phy
usb: Handle USB3 remote wakeup for LPM enabled devices correctly
drivers/usb/typec/tps6598x.c: fix 4CC cmd write
drivers/usb/typec/tps6598x.c: fix portinfo width
usb: storage: scsiglue: Do not skip VPD if try_vpd_pages is set
usb: renesas_usbhs: add a workaround for a race condition of workqueue
usb: gadget: udc: renesas_usb3: remove redundant assignment to ret
usb: dwc2: use a longer AHB idle timeout in dwc2_core_reset()
USB: gadget: function: fix issue Unneeded variable: "value"
...
Linus Torvalds [Thu, 11 Jul 2019 22:38:21 +0000 (15:38 -0700)]
Merge tag 'tty-5.3-rc1' of git://git./linux/kernel/git/gregkh/tty
Pull tty / serial driver updates from Greg KH:
"Here is the "large" TTY and Serial driver update for 5.3-rc1.
It's in the negative number of lines overall as we removed an obsolete
serial driver that was causing problems for some people who were
trying to clean up some apis (the mpsc.c driver, which only worked for
some pre-production hardware that no one has anymore.)
Other than that, lots of tiny changes, cleaning up small things along
with some platform-specific serial driver updates.
All of these have been in linux-next for a while now with no reported
issues"
* tag 'tty-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (68 commits)
tty: serial: fsl_lpuart: add imx8qxp support
serial: imx: set_termios(): preserve RTS state
serial: imx: set_termios(): clarify RTS/CTS bits calculation
serial: imx: set_termios(): factor-out 'ucr2' initial value
serial: sh-sci: Terminate TX DMA during buffer flushing
serial: sh-sci: Fix TX DMA buffer flushing and workqueue races
serial: mpsc: Remove obsolete MPSC driver
serial: 8250: 8250_core: Fix missing unlock on error in serial8250_register_8250_port()
serial: stm32: add RX and TX FIFO flush
serial: stm32: add support of RX FIFO threshold
serial: stm32: add support of TX FIFO threshold
serial: stm32: update PIO transmission
serial: stm32: add support of timeout interrupt for RX
Revert "serial: 8250: Don't service RX FIFO if interrupts are disabled"
tty/serial/8250: use mctrl_gpio helpers
serial: mctrl_gpio: Check if GPIO property exisits before requesting it
serial: 8250: pericom_do_set_divisor can be static
tty: serial_core: Set port active bit in uart_port_activate
serial: 8250: Add MSR/MCR TIOCM conversion wrapper functions
serial: 8250: factor out serial8250_{set,clear}_THRI() helpers
...
Linus Torvalds [Thu, 11 Jul 2019 22:36:02 +0000 (15:36 -0700)]
Merge tag 'staging-5.3-rc1' of git://git./linux/kernel/git/gregkh/staging
Pull staging and IIO driver updates from Greg KH:
"Here is the big Staging and IIO driver update for 5.3-rc1.
Lots of new IIO drivers are in here, along with loads of tiny staging
driver cleanups and fixes. Overall we almost break even with the same
lines added as removed.
Full details are in the shortlog, they are too large to list here.
All of these changes have been in linux-next for a while with no
reported issues"
* tag 'staging-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (608 commits)
staging: kpc2000: simplify comparison to NULL in fileops.c
staging: kpc2000: simplify comparison to NULL in dma.c
staging: kpc2000: simplify comparison to NULL in kpc2000_spi.c
staging: rtl8723bs: hal: remove redundant assignment to packetType
staging: rtl8723bs: Change return type of hal_btcoex_IsBtDisabled()
staging: rtl8723bs: Remove rtw_btcoex_DisplayBtCoexInfo()
staging: rtl8723bs: Remove function rtw_btcoex_GetDBG()
staging: rtl8723bs: Remove function rtw_btcoex_SetDBG()
staging: rtl8723bs: Remove rtw_btcoex_IsBTCoexCtrlAMPDUSize()
staging: rtl8723bs: Remove rtw_btcoex_BtInfoNotify()
staging: rtl8723bs: Remove rtw_btcoex_ScanNotify()
staging: rtl8723bs: Remove rtw_btcoex_SetSingleAntPath()
staging: rtl8723bs: Remove rtw_btcoex_SetPGAntNum()
staging: rtl8192e: remove redundant initialization of rtstatus
staging: rtl8723bs: Remove rtw_btcoex_GetRaMask()
staging: rtl8723bs: Remove rtw_btcoex_SetChipType()
staging: rtl8723bs: Remove rtw_btcoex_ConnectNotify()
staging: rtl8723bs: Remove rtw_btcoex_SetBTCoexist()
staging: rtl8723bs: Remove rtw_btcoex_IsBtDisabled()
staging: rtl8723bs: Remove rtw_btcoex_IsBtControlLps()
...
Linus Torvalds [Thu, 11 Jul 2019 22:34:05 +0000 (15:34 -0700)]
Merge tag 'char-misc-5.3-rc1' of git://git./linux/kernel/git/gregkh/char-misc
Pull char / misc driver updates from Greg KH:
"Here is the "large" pull request for char and misc and other assorted
smaller driver subsystems for 5.3-rc1.
It seems that this tree is becoming the funnel point of lots of
smaller driver subsystems, which is fine for me, but that's why it is
getting larger over time and does not just contain stuff under
drivers/char/ and drivers/misc.
Lots of small updates all over the place here from different driver
subsystems:
- habana driver updates
- coresight driver updates
- documentation file movements and updates
- Android binder fixes and updates
- extcon driver updates
- google firmware driver updates
- fsi driver updates
- smaller misc and char driver updates
- soundwire driver updates
- nvmem driver updates
- w1 driver fixes
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (188 commits)
coresight: Do not default to CPU0 for missing CPU phandle
dt-bindings: coresight: Change CPU phandle to required property
ocxl: Allow contexts to be attached with a NULL mm
fsi: sbefifo: Don't fail operations when in SBE IPL state
coresight: tmc: Smatch: Fix potential NULL pointer dereference
coresight: etm3x: Smatch: Fix potential NULL pointer dereference
coresight: Potential uninitialized variable in probe()
coresight: etb10: Do not call smp_processor_id from preemptible
coresight: tmc-etf: Do not call smp_processor_id from preemptible
coresight: tmc-etr: alloc_perf_buf: Do not call smp_processor_id from preemptible
coresight: tmc-etr: Do not call smp_processor_id() from preemptible
docs: misc-devices: convert files without extension to ReST
fpga: dfl: fme: align PR buffer size per PR datawidth
fpga: dfl: fme: remove copy_to_user() in ioctl for PR
fpga: dfl-fme-mgr: fix FME_PR_INTFC_ID register address.
intel_th: msu: Start read iterator from a non-empty window
intel_th: msu: Split sgt array and pointer in multiwindow mode
intel_th: msu: Support multipage blocks
intel_th: pci: Add Ice Lake NNPI support
intel_th: msu: Fix single mode with disabled IOMMU
...
Linus Torvalds [Thu, 11 Jul 2019 22:32:11 +0000 (15:32 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/hid/hid
Pull HID updates from Jiri Kosina:
- Documentation conversion to ReST, from Mauro Carvalho Chehab
- Wacom MobileStudio Pro support, from Ping Cheng
- Wacom 2nd Gen Intuos Pro Small support, from Aaron Armstrong Skomra
- assorted small fixes and device ID additions
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid:
HID: Add another Primax PIXART OEM mouse quirk
HID: wacom: generic: add touchring adjustment for 2nd Gen Pro Small
docs: hid: convert to ReST
HID: remove NO_D3 flag when remove driver
HID: wacom: add new MobileStudio Pro support
HID: wacom: generic: read the number of expected touches on a per collection basis
HID: wacom: generic: support the 'report valid' usage for touch
HID: wacom: generic: read HID_DG_CONTACTMAX from any feature report
HID: wacom: Add 2nd gen Intuos Pro Small support
HID: uclogic: Add support for Ugee Rainbow CV720
HID: logitech-dj: fix return value of logi_dj_recv_query_hidpp_devices
HID: logitech-hidpp: HID: make const array consumer_rdesc_start static
HID: logitech-dj: make const array template static
HID: wacom: correct touch resolution x/y typo
HID: wacom: generic: Correct pad syncing
HID: wacom: generic: only switch the mode on devices with LEDs
HID: logitech-dj: Add usb-id for the 27MHz MX3000 receiver
Linus Torvalds [Thu, 11 Jul 2019 22:30:05 +0000 (15:30 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/livepatching/livepatching
Pull livepatching updates from Jiri Kosina:
- stacktrace handling improvements from Miroslav benes
- debug output improvements from Petr Mladek
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/livepatching/livepatching:
livepatch: Remove duplicate warning about missing reliable stacktrace support
Revert "livepatch: Remove reliable stacktrace check in klp_try_switch_task()"
stacktrace: Remove weak version of save_stack_trace_tsk_reliable()
livepatch: Use static buffer for debugging messages under rq lock
livepatch: Remove stale kobj_added entries from kernel-doc descriptions
Linus Torvalds [Thu, 11 Jul 2019 22:17:41 +0000 (15:17 -0700)]
Merge tag 'scsi-sg' of git://git./linux/kernel/git/jejb/scsi
Pull SCSI scatter-gather list updates from James Bottomley:
"This topic branch covers a fundamental change in how our sg lists are
allocated to make mq more efficient by reducing the size of the
preallocated sg list.
This necessitates a large number of driver changes because the
previous guarantee that if a driver specified SG_ALL as the size of
its scatter list, it would get a non-chained list and didn't need to
bother with scatterlist iterators is now broken and every driver
*must* use scatterlist iterators.
This was broken out as a separate topic because we need to convert all
the drivers before pulling the trigger and unconverted drivers kept
being found, necessitating a rebase"
* tag 'scsi-sg' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (21 commits)
scsi: core: don't preallocate small SGL in case of NO_SG_CHAIN
scsi: lib/sg_pool.c: clear 'first_chunk' in case of no preallocation
scsi: core: avoid preallocating big SGL for data
scsi: core: avoid preallocating big SGL for protection information
scsi: lib/sg_pool.c: improve APIs for allocating sg pool
scsi: esp: use sg helper to iterate over scatterlist
scsi: NCR5380: use sg helper to iterate over scatterlist
scsi: wd33c93: use sg helper to iterate over scatterlist
scsi: ppa: use sg helper to iterate over scatterlist
scsi: pcmcia: nsp_cs: use sg helper to iterate over scatterlist
scsi: imm: use sg helper to iterate over scatterlist
scsi: aha152x: use sg helper to iterate over scatterlist
scsi: s390: zfcp_fc: use sg helper to iterate over scatterlist
scsi: staging: unisys: visorhba: use sg helper to iterate over scatterlist
scsi: usb: image: microtek: use sg helper to iterate over scatterlist
scsi: pmcraid: use sg helper to iterate over scatterlist
scsi: ipr: use sg helper to iterate over scatterlist
scsi: mvumi: use sg helper to iterate over scatterlist
scsi: lpfc: use sg helper to iterate over scatterlist
scsi: advansys: use sg helper to iterate over scatterlist
...
Linus Torvalds [Thu, 11 Jul 2019 22:14:01 +0000 (15:14 -0700)]
Merge tag 'scsi-misc' of git://git./linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly update of the usual drivers: qla2xxx, hpsa, lpfc, ufs,
mpt3sas, ibmvscsi, megaraid_sas, bnx2fc and hisi_sas as well as the
removal of the osst driver (I heard from Willem privately that he
would like the driver removed because all his test hardware has
failed). Plus number of minor changes, spelling fixes and other
trivia.
The big merge conflict this time around is the SPDX licence tags.
Following discussion on linux-next, we believe our version to be more
accurate than the one in the tree, so the resolution is to take our
version for all the SPDX conflicts"
Note on the SPDX license tag conversion conflicts: the SCSI tree had
done its own SPDX conversion, which in some cases conflicted with the
treewide ones done by Thomas & co.
In almost all cases, the conflicts were purely syntactic: the SCSI tree
used the old-style SPDX tags ("GPL-2.0" and "GPL-2.0+") while the
treewide conversion had used the new-style ones ("GPL-2.0-only" and
"GPL-2.0-or-later").
In these cases I picked the new-style one.
In a few cases, the SPDX conversion was actually different, though. As
explained by James above, and in more detail in a pre-pull-request
thread:
"The other problem is actually substantive: In the libsas code Luben
Tuikov originally specified gpl 2.0 only by dint of stating:
* This file is licensed under GPLv2.
In all the libsas files, but then muddied the water by quoting GPLv2
verbatim (which includes the or later than language). So for these
files Christoph did the conversion to v2 only SPDX tags and Thomas
converted to v2 or later tags"
So in those cases, where the spdx tag substantially mattered, I took the
SCSI tree conversion of it, but then also took the opportunity to turn
the old-style "GPL-2.0" into a new-style "GPL-2.0-only" tag.
Similarly, when there were whitespace differences or other differences
to the comments around the copyright notices, I took the version from
the SCSI tree as being the more specific conversion.
Finally, in the spdx conversions that had no conflicts (because the
treewide ones hadn't been done for those files), I just took the SCSI
tree version as-is, even if it was old-style. The old-style conversions
are perfectly valid, even if the "-only" and "-or-later" versions are
perhaps more descriptive.
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (185 commits)
scsi: qla2xxx: move IO flush to the front of NVME rport unregistration
scsi: qla2xxx: Fix NVME cmd and LS cmd timeout race condition
scsi: qla2xxx: on session delete, return nvme cmd
scsi: qla2xxx: Fix kernel crash after disconnecting NVMe devices
scsi: megaraid_sas: Update driver version to 07.710.06.00-rc1
scsi: megaraid_sas: Introduce various Aero performance modes
scsi: megaraid_sas: Use high IOPS queues based on IO workload
scsi: megaraid_sas: Set affinity for high IOPS reply queues
scsi: megaraid_sas: Enable coalescing for high IOPS queues
scsi: megaraid_sas: Add support for High IOPS queues
scsi: megaraid_sas: Add support for MPI toolbox commands
scsi: megaraid_sas: Offload Aero RAID5/6 division calculations to driver
scsi: megaraid_sas: RAID1 PCI bandwidth limit algorithm is applicable for only Ventura
scsi: megaraid_sas: megaraid_sas: Add check for count returned by HOST_DEVICE_LIST DCMD
scsi: megaraid_sas: Handle sequence JBOD map failure at driver level
scsi: megaraid_sas: Don't send FPIO to RL Bypass queue
scsi: megaraid_sas: In probe context, retry IOC INIT once if firmware is in fault
scsi: megaraid_sas: Release Mutex lock before OCR in case of DCMD timeout
scsi: megaraid_sas: Call disable_irq from process IRQ poll
scsi: megaraid_sas: Remove few debug counters from IO path
...
Linus Torvalds [Thu, 11 Jul 2019 21:44:13 +0000 (14:44 -0700)]
Merge tag 'hwmon-for-v5.3' of git://git./linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
- New drivers for Infineon PXE1610 and IRPS5401
- Minor improvements, cleanup, and fixes in several drivers
* tag 'hwmon-for-v5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (33 commits)
hwmon: (ina3221) Add of_node_put() before return
hwmon: (gpio-fan) fix sysfs notifications and udev events for gpio-fan alarms
hwmon: (gpio-fan) move fan_alarm_init after devm_hwmon_device_register_with_groups
hwmon: (lm90) Introduce function to update configuration register
hwmon: (lm90) Cache configuration register value
hwmon: (lm90) Fix max6658 sporadic wrong temperature reading
hwmon: (nct7904) Changes comments in probe function.
hwmon: (nct7904) Add error handling in probe function.
hwmon: Convert remaining drivers to use SPDX identifier
hwmon: (max6650) Fix unused variable warning
hwmon: (pmbus/adm1275) Fix power sampling support
hwmon: (lm90) simplify getting the adapter of a client
hwmon: (asus_atk0110) no need to check return value of debugfs_create functions
hwmon: (max6650) Fix minor formatting issues
hwmon: (max6650) Improve error handling in max6650_update_device
hwmon: (max6650) Read non-volatile registers only once
hwmon: (max6650) Convert to use devm_hwmon_device_register_with_info
hwmon: (max6650) Simplify alarm handling
hwmon: (max6650) Cache alarm_en register
hwmon: (max6650) Declare valid as boolean
...
Linus Torvalds [Thu, 11 Jul 2019 21:42:44 +0000 (14:42 -0700)]
Merge tag 'loadpin-v5.3-rc1' of git://git./linux/kernel/git/kees/linux
Pull security/loadpin updates from Kees Cook:
- Allow exclusion of specific file types (Ke Wu)
* tag 'loadpin-v5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
security/loadpin: Allow to exclude specific file types
Linus Torvalds [Thu, 11 Jul 2019 21:40:32 +0000 (14:40 -0700)]
Merge tag 'pstore-v5.3-rc1' of git://git./linux/kernel/git/kees/linux
Pull pstore updates from Kees Cook:
- Improve backward compatibility with older Chromebooks (Douglas
Anderson)
- Refactor debugfs initialization (Greg KH)
- Fix double-free in pstore_mkfile() failure path (Norbert Manthey)
* tag 'pstore-v5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
pstore: Fix double-free in pstore_mkfile() failure path
pstore: no need to check return value of debugfs_create functions
pstore/ram: Improve backward compatibility with older Chromebooks
Linus Torvalds [Thu, 11 Jul 2019 20:54:00 +0000 (13:54 -0700)]
Merge branch 'x86-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"A collection of assorted fixes:
- Fix for the pinned cr0/4 fallout which escaped all testing efforts
because the kvm-intel module was never loaded when the kernel was
compiled with CONFIG_PARAVIRT=n. The cr0/4 accessors are moved out
of line and static key is now solely used in the core code and
therefore can stay in the RO after init section. So the kvm-intel
and other modules do not longer reference the (read only) static
key which the module loader tried to update.
- Prevent an infinite loop in arch_stack_walk_user() by breaking out
of the loop once the return address is detected to be 0.
- Prevent the int3_emulate_call() selftest from corrupting the stack
when KASAN is enabled. KASASN clobbers more registers than covered
by the emulated call implementation. Convert the int3_magic()
selftest to a ASM function so the compiler cannot KASANify it.
- Unbreak the build with old GCC versions and with the Gold linker by
reverting the 'Move of _etext to the actual end of .text'. In both
cases the build fails with 'Invalid absolute R_X86_64_32S
relocation: _etext'
- Initialize the context lock for init_mm, which was never an issue
until the alternatives code started to use a temporary mm for
patching.
- Fix a build warning vs. the LOWMEM_PAGES constant where clang
complains rightfully about a signed integer overflow in the shift
operation by converting the operand to an ULL.
- Adjust the misnamed ENDPROC() of common_spurious in the 32bit entry
code"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/stacktrace: Prevent infinite loop in arch_stack_walk_user()
x86/asm: Move native_write_cr0/4() out of line
x86/pgtable/32: Fix LOWMEM_PAGES constant
x86/alternatives: Fix int3_emulate_call() selftest stack corruption
x86/entry/32: Fix ENDPROC of common_spurious
Revert "x86/build: Move _etext to actual end of .text"
x86/ldt: Initialize the context lock for init_mm
Linus Torvalds [Thu, 11 Jul 2019 20:52:23 +0000 (13:52 -0700)]
Merge branch 'timers-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull timer fixes from Thomas Gleixner:
"Two small fixes from the timer departement:
- Prevent the compiler from converting the nanoseconds adjustment
loop in the VDSO update function to a division (__udivdi3) by using
the __iter_div_u64_rem() inline function which exists to prevent
exactly that problem.
- Fix the wrong argument order of the GENMASK macro in the NPCM timer
driver"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
timekeeping/vsyscall: Use __iter_div_u64_rem()
clocksource/drivers/npcm: Fix misuse of GENMASK macro
Linus Torvalds [Thu, 11 Jul 2019 20:50:44 +0000 (13:50 -0700)]
Merge branch 'core-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull stacktrace fix from Thomas Gleixner:
"Fix yet another instance of kernel thread check which ignores that
kernel threads can call use_mm()"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
stacktrace: Use PF_KTHREAD to check for kernel threads
Linus Torvalds [Thu, 11 Jul 2019 20:48:36 +0000 (13:48 -0700)]
Merge branch 'irq-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull irq fixes from Thomas Gleixner:
"Two small fixes for interrupt chip drivers:
- Prevent UAF in the new RZA1 chip driver
- Fix the wrong argument order of the GENMASK macro in the GIC code"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/gic-v3-its: Fix misuse of GENMASK macro
irqchip/renesas-rza1: Prevent use-after-free in rza1_irqc_probe()
Linus Torvalds [Thu, 11 Jul 2019 18:17:09 +0000 (11:17 -0700)]
Merge tag 'acpi-5.3-rc1-2' of git://git./linux/kernel/git/rafael/linux-pm
Pull ACPI fix from Rafael Wysocki:
"Revert a recent ACPICA commit causing systems to hang at boot time"
* tag 'acpi-5.3-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
Revert "ACPICA: Update table load object initialization"
Linus Torvalds [Thu, 11 Jul 2019 17:55:49 +0000 (10:55 -0700)]
Merge git://git./linux/kernel/git/davem/net-next
Pull networking updates from David Miller:
"Some highlights from this development cycle:
1) Big refactoring of ipv6 route and neigh handling to support
nexthop objects configurable as units from userspace. From David
Ahern.
2) Convert explored_states in BPF verifier into a hash table,
significantly decreased state held for programs with bpf2bpf
calls, from Alexei Starovoitov.
3) Implement bpf_send_signal() helper, from Yonghong Song.
4) Various classifier enhancements to mvpp2 driver, from Maxime
Chevallier.
5) Add aRFS support to hns3 driver, from Jian Shen.
6) Fix use after free in inet frags by allocating fqdirs dynamically
and reworking how rhashtable dismantle occurs, from Eric Dumazet.
7) Add act_ctinfo packet classifier action, from Kevin
Darbyshire-Bryant.
8) Add TFO key backup infrastructure, from Jason Baron.
9) Remove several old and unused ISDN drivers, from Arnd Bergmann.
10) Add devlink notifications for flash update status to mlxsw driver,
from Jiri Pirko.
11) Lots of kTLS offload infrastructure fixes, from Jakub Kicinski.
12) Add support for mv88e6250 DSA chips, from Rasmus Villemoes.
13) Various enhancements to ipv6 flow label handling, from Eric
Dumazet and Willem de Bruijn.
14) Support TLS offload in nfp driver, from Jakub Kicinski, Dirk van
der Merwe, and others.
15) Various improvements to axienet driver including converting it to
phylink, from Robert Hancock.
16) Add PTP support to sja1105 DSA driver, from Vladimir Oltean.
17) Add mqprio qdisc offload support to dpaa2-eth, from Ioana
Radulescu.
18) Add devlink health reporting to mlx5, from Moshe Shemesh.
19) Convert stmmac over to phylink, from Jose Abreu.
20) Add PTP PHC (Physical Hardware Clock) support to mlxsw, from
Shalom Toledo.
21) Add nftables SYNPROXY support, from Fernando Fernandez Mancera.
22) Convert tcp_fastopen over to use SipHash, from Ard Biesheuvel.
23) Track spill/fill of constants in BPF verifier, from Alexei
Starovoitov.
24) Support bounded loops in BPF, from Alexei Starovoitov.
25) Various page_pool API fixes and improvements, from Jesper Dangaard
Brouer.
26) Just like ipv4, support ref-countless ipv6 route handling. From
Wei Wang.
27) Support VLAN offloading in aquantia driver, from Igor Russkikh.
28) Add AF_XDP zero-copy support to mlx5, from Maxim Mikityanskiy.
29) Add flower GRE encap/decap support to nfp driver, from Pieter
Jansen van Vuuren.
30) Protect against stack overflow when using act_mirred, from John
Hurley.
31) Allow devmap map lookups from eBPF, from Toke Høiland-Jørgensen.
32) Use page_pool API in netsec driver, Ilias Apalodimas.
33) Add Google gve network driver, from Catherine Sullivan.
34) More indirect call avoidance, from Paolo Abeni.
35) Add kTLS TX HW offload support to mlx5, from Tariq Toukan.
36) Add XDP_REDIRECT support to bnxt_en, from Andy Gospodarek.
37) Add MPLS manipulation actions to TC, from John Hurley.
38) Add sending a packet to connection tracking from TC actions, and
then allow flower classifier matching on conntrack state. From
Paul Blakey.
39) Netfilter hw offload support, from Pablo Neira Ayuso"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2080 commits)
net/mlx5e: Return in default case statement in tx_post_resync_params
mlx5: Return -EINVAL when WARN_ON_ONCE triggers in mlx5e_tls_resync().
net: dsa: add support for BRIDGE_MROUTER attribute
pkt_sched: Include const.h
net: netsec: remove static declaration for netsec_set_tx_de()
net: netsec: remove superfluous if statement
netfilter: nf_tables: add hardware offload support
net: flow_offload: rename tc_cls_flower_offload to flow_cls_offload
net: flow_offload: add flow_block_cb_is_busy() and use it
net: sched: remove tcf block API
drivers: net: use flow block API
net: sched: use flow block API
net: flow_offload: add flow_block_cb_{priv, incref, decref}()
net: flow_offload: add list handling functions
net: flow_offload: add flow_block_cb_alloc() and flow_block_cb_free()
net: flow_offload: rename TCF_BLOCK_BINDER_TYPE_* to FLOW_BLOCK_BINDER_TYPE_*
net: flow_offload: rename TC_BLOCK_{UN}BIND to FLOW_BLOCK_{UN}BIND
net: flow_offload: add flow_block_cb_setup_simple()
net: hisilicon: Add an tx_desc to adapt HI13X1_GMAC
net: hisilicon: Add an rx_desc to adapt HI13X1_GMAC
...
Linus Torvalds [Thu, 11 Jul 2019 17:09:44 +0000 (10:09 -0700)]
Merge tag 'clone3-v5.3' of git://git./linux/kernel/git/brauner/linux
Pull clone3 system call from Christian Brauner:
"This adds the clone3 syscall which is an extensible successor to clone
after we snagged the last flag with CLONE_PIDFD during the 5.2 merge
window for clone(). It cleanly supports all of the flags from clone()
and thus all legacy workloads.
There are few user visible differences between clone3 and clone.
First, CLONE_DETACHED will cause EINVAL with clone3 so we can reuse
this flag. Second, the CSIGNAL flag is deprecated and will cause
EINVAL to be reported. It is superseeded by a dedicated "exit_signal"
argument in struct clone_args thus freeing up even more flags. And
third, clone3 gives CLONE_PIDFD a dedicated return argument in struct
clone_args instead of abusing CLONE_PARENT_SETTID's parent_tidptr
argument.
The clone3 uapi is designed to be easy to handle on 32- and 64 bit:
/* uapi */
struct clone_args {
__aligned_u64 flags;
__aligned_u64 pidfd;
__aligned_u64 child_tid;
__aligned_u64 parent_tid;
__aligned_u64 exit_signal;
__aligned_u64 stack;
__aligned_u64 stack_size;
__aligned_u64 tls;
};
and a separate kernel struct is used that uses proper kernel typing:
/* kernel internal */
struct kernel_clone_args {
u64 flags;
int __user *pidfd;
int __user *child_tid;
int __user *parent_tid;
int exit_signal;
unsigned long stack;
unsigned long stack_size;
unsigned long tls;
};
The system call comes with a size argument which enables the kernel to
detect what version of clone_args userspace is passing in. clone3
validates that any additional bytes a given kernel does not know about
are set to zero and that the size never exceeds a page.
A nice feature is that this patchset allowed us to cleanup and
simplify various core kernel codepaths in kernel/fork.c by making the
internal _do_fork() function take struct kernel_clone_args even for
legacy clone().
This patch also unblocks the time namespace patchset which wants to
introduce a new CLONE_TIMENS flag.
Note, that clone3 has only been wired up for x86{_32,64}, arm{64}, and
xtensa. These were the architectures that did not require special
massaging.
Other architectures treat fork-like system calls individually and
after some back and forth neither Arnd nor I felt confident that we
dared to add clone3 unconditionally to all architectures. We agreed to
leave this up to individual architecture maintainers. This is why
there's an additional patch that introduces __ARCH_WANT_SYS_CLONE3
which any architecture can set once it has implemented support for
clone3. The patch also adds a cond_syscall(clone3) for architectures
such as nios2 or h8300 that generate their syscall table by simply
including asm-generic/unistd.h. The hope is to get rid of
__ARCH_WANT_SYS_CLONE3 and cond_syscall() rather soon"
* tag 'clone3-v5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux:
arch: handle arches who do not yet define clone3
arch: wire-up clone3() syscall
fork: add clone3
Eiichi Tsukata [Thu, 11 Jul 2019 02:35:01 +0000 (11:35 +0900)]
x86/stacktrace: Prevent infinite loop in arch_stack_walk_user()
arch_stack_walk_user() checks `if (fp == frame.next_fp)` to prevent a
infinite loop by self reference but it's not enogh for circular reference.
Once a lack of return address is found, there is no point to continue the
loop, so break out.
Fixes:
02b67518e2b1 ("tracing: add support for userspace stacktraces in tracing/iter_ctrl")
Signed-off-by: Eiichi Tsukata <devel@etsukata.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Link: https://lkml.kernel.org/r/20190711023501.963-1-devel@etsukata.com
Linus Torvalds [Thu, 11 Jul 2019 05:17:21 +0000 (22:17 -0700)]
Merge tag 'pidfd-updates-v5.3' of git://git./linux/kernel/git/brauner/linux
Pull pidfd updates from Christian Brauner:
"This adds two main features.
- First, it adds polling support for pidfds. This allows process
managers to know when a (non-parent) process dies in a race-free
way.
The notification mechanism used follows the same logic that is
currently used when the parent of a task is notified of a child's
death. With this patchset it is possible to put pidfds in an
{e}poll loop and get reliable notifications for process (i.e.
thread-group) exit.
- The second feature compliments the first one by making it possible
to retrieve pollable pidfds for processes that were not created
using CLONE_PIDFD.
A lot of processes get created with traditional PID-based calls
such as fork() or clone() (without CLONE_PIDFD). For these
processes a caller can currently not create a pollable pidfd. This
is a problem for Android's low memory killer (LMK) and service
managers such as systemd.
Both patchsets are accompanied by selftests.
It's perhaps worth noting that the work done so far and the work done
in this branch for pidfd_open() and polling support do already see
some adoption:
- Android is in the process of backporting this work to all their LTS
kernels [1]
- Service managers make use of pidfd_send_signal but will need to
wait until we enable waiting on pidfds for full adoption.
- And projects I maintain make use of both pidfd_send_signal and
CLONE_PIDFD [2] and will use polling support and pidfd_open() too"
[1] https://android-review.googlesource.com/q/topic:%22pidfd+polling+support+4.9+backport%22
https://android-review.googlesource.com/q/topic:%22pidfd+polling+support+4.14+backport%22
https://android-review.googlesource.com/q/topic:%22pidfd+polling+support+4.19+backport%22
[2] https://github.com/lxc/lxc/blob/
aab6e3eb73c343231cdde775db938994fc6f2803/src/lxc/start.c#L1753
* tag 'pidfd-updates-v5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux:
tests: add pidfd_open() tests
arch: wire-up pidfd_open()
pid: add pidfd_open()
pidfd: add polling selftests
pidfd: add polling support
Linus Torvalds [Thu, 11 Jul 2019 04:44:07 +0000 (21:44 -0700)]
Merge tag 'm68k-for-v5.3-tag2' of git://git./linux/kernel/git/geert/linux-m68k
Pull m68k fix from Geert Uytterhoeven:
"Don't select ARCH_HAS_DMA_PREP_COHERENT for nommu or coldfire.
This is a fix for an issue detected in next, to avoid introducing
build failures when merging Christoph's dma-mapping tree later"
* tag 'm68k-for-v5.3-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k: Don't select ARCH_HAS_DMA_PREP_COHERENT for nommu or coldfire
Linus Torvalds [Thu, 11 Jul 2019 04:42:03 +0000 (21:42 -0700)]
Merge branch 'for-next' of git://git./linux/kernel/git/gerg/m68knommu
Pull m68nommu updates from Greg Ungerer:
"A series of cleanups for the FLAT format binary loader, binfmt_flat,
from Christoph.
The end goal is to support no-MMU on RISC-V, and the last patch
enables that"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
riscv: add binfmt_flat support
binfmt_flat: don't offset the data start
binfmt_flat: move the MAX_SHARED_LIBS definition to binfmt_flat.c
binfmt_flat: remove the persistent argument from flat_get_addr_from_rp
binfmt_flat: provide an asm-generic/flat.h
binfmt_flat: make support for old format binaries optional
binfmt_flat: add a ARCH_HAS_BINFMT_FLAT option
binfmt_flat: add endianess annotations
binfmt_flat: use fixed size type for the on-disk format
binfmt_flat: consolidate two version of flat_v2_reloc_t
binfmt_flat: remove the unused OLD_FLAT_FLAG_RAM definition
binfmt_flat: remove the uapi <linux/flat.h> header
binfmt_flat: replace flat_argvp_envp_on_stack with a Kconfig variable
binfmt_flat: remove flat_old_ram_flag
binfmt_flat: provide a default version of flat_get_relocate_addr
binfmt_flat: remove flat_set_persistent
binfmt_flat: remove flat_reloc_valid
Linus Torvalds [Thu, 11 Jul 2019 04:22:43 +0000 (21:22 -0700)]
Merge tag 'nfsd-5.3' of git://linux-nfs.org/~bfields/linux
Pull nfsd updates from Bruce Fields:
"Highlights:
- Add a new /proc/fs/nfsd/clients/ directory which exposes some
long-requested information about NFSv4 clients (like open files)
and allows forced revocation of client state.
- Replace the global duplicate reply cache by a cache per network
namespace; previously, a request in one network namespace could
incorrectly match an entry from another, though we haven't seen
this in production. This is the last remaining container bug that
I'm aware of; at this point you should be able to run separate
nfsd's in each network namespace, each with their own set of
exports, and everything should work.
- Cleanup and modify lock code to show the pid of lockd as the owner
of NLM locks. This is the correct version of the bugfix originally
attempted in
b8eee0e90f97 ("lockd: Show pid of lockd for remote
locks")"
* tag 'nfsd-5.3' of git://linux-nfs.org/~bfields/linux: (34 commits)
nfsd: Make __get_nfsdfs_client() static
nfsd: Make two functions static
nfsd: Fix misuse of strlcpy
sunrpc/cache: remove the exporting of cache_seq_next
nfsd: decode implementation id
nfsd: create xdr_netobj_dup helper
nfsd: allow forced expiration of NFSv4 clients
nfsd: create get_nfsdfs_clp helper
nfsd4: show layout stateids
nfsd: show lock and deleg stateids
nfsd4: add file to display list of client's opens
nfsd: add more information to client info file
nfsd: escape high characters in binary data
nfsd: copy client's address including port number to cl_addr
nfsd4: add a client info file
nfsd: make client/ directory names small ints
nfsd: add nfsd/clients directory
nfsd4: use reference count to free client
nfsd: rename cl_refcount
nfsd: persist nfsd filesystem across mounts
...
Linus Torvalds [Thu, 11 Jul 2019 04:20:05 +0000 (21:20 -0700)]
Merge tag 'gfs2-for-5.3' of git://git./linux/kernel/git/gfs2/linux-gfs2
Pull gfs2 updates from Andreas Gruenbacher:
"Some relatively minor changes for gfs2:
- An initial batch of obvious cleanups and fixes from Bob's recovery
patch queue.
- Two iomap conversion patches and some cleanups from Christoph
Hellwig.
- A cosmetic cleanup from Kefeng Wang (Huawei).
- Another minor fix and cleanup by me"
* tag 'gfs2-for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/gfs2/linux-gfs2:
gfs2: Remove unused gfs2_iomap_alloc argument
gfs2: don't use buffer_heads in gfs2_allocate_page_backing
gfs2: use iomap_bmap instead of generic_block_bmap
gfs2: mark stuffed_readpage static
gfs2: merge gfs2_writepage_common into gfs2_writepage
gfs2: merge gfs2_writeback_aops and gfs2_ordered_aops
gfs2: remove the unused gfs2_stuffed_write_end function
gfs2: use page_offset in gfs2_page_mkwrite
gfs2: replace more printk with calls to fs_info and friends
gfs2: dump fsid when dumping glock problems
gfs2: simplify gfs2_freeze by removing case
gfs2: Rename SDF_SHUTDOWN to SDF_WITHDRAWN
gfs2: Warn when a journal replay overwrites a rgrp with buffers
gfs2: log which portion of the journal is replayed
gfs2: eliminate tr_num_revoke_rm
gfs2: kthread and remount improvements
gfs2: Use IS_ERR_OR_NULL
gfs2: Clean up freeing struct gfs2_sbd
Linus Torvalds [Thu, 11 Jul 2019 04:06:01 +0000 (21:06 -0700)]
Merge tag 'ext4_for_linus' of git://git./linux/kernel/git/tytso/ext4
Pull ext4 updates from Ted Ts'o:
"Many bug fixes and cleanups, and an optimization for case-insensitive
lookups"
* tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: fix coverity warning on error path of filename setup
ext4: replace ktype default_attrs with default_groups
ext4: rename htree_inline_dir_to_tree() to ext4_inlinedir_to_tree()
ext4: refactor initialize_dirent_tail()
ext4: rename "dirent_csum" functions to use "dirblock"
ext4: allow directory holes
jbd2: drop declaration of journal_sync_buffer()
ext4: use jbd2_inode dirty range scoping
jbd2: introduce jbd2_inode dirty range scoping
mm: add filemap_fdatawait_range_keep_errors()
ext4: remove redundant assignment to node
ext4: optimize case-insensitive lookups
ext4: make __ext4_get_inode_loc plug
ext4: clean up kerneldoc warnigns when building with W=1
ext4: only set project inherit bit for directory
ext4: enforce the immutable flag on open files
ext4: don't allow any modifications to an immutable file
jbd2: fix typo in comment of journal_submit_inode_data_buffers
jbd2: fix some print format mistakes
ext4: gracefully handle ext4_break_layouts() failure during truncate
Linus Torvalds [Thu, 11 Jul 2019 03:55:33 +0000 (20:55 -0700)]
Merge tag 'afs-next-
20190628' of git://git./linux/kernel/git/dhowells/linux-fs
Pull afs updates from David Howells:
"A set of minor changes for AFS:
- Remove an unnecessary check in afs_unlink()
- Add a tracepoint for tracking callback management
- Add a tracepoint for afs_server object usage
- Use struct_size()
- Add mappings for AFS UAE abort codes to Linux error codes, using
symbolic names rather than hex numbers in the .c file"
* tag 'afs-next-
20190628' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs:
afs: Add support for the UAE error table
fs/afs: use struct_size() in kzalloc()
afs: Trace afs_server usage
afs: Add some callback management tracepoints
afs: afs_unlink() doesn't need to check dentry->d_inode
Linus Torvalds [Thu, 11 Jul 2019 03:51:03 +0000 (20:51 -0700)]
Merge tag 'fscrypt-for-linus' of git://git./fs/fscrypt/fscrypt
Pull fscrypt updates from Eric Biggers:
- Preparations for supporting encryption on ext4 filesystems where the
filesystem block size is smaller than PAGE_SIZE.
- Don't allow setting encryption policies on dead directories.
- Various cleanups.
* tag 'fscrypt-for-linus' of git://git.kernel.org/pub/scm/fs/fscrypt/fscrypt:
fscrypt: document testing with xfstests
fscrypt: remove selection of CONFIG_CRYPTO_SHA256
fscrypt: remove unnecessary includes of ratelimit.h
fscrypt: don't set policy for a dead directory
ext4: encrypt only up to last block in ext4_bio_write_page()
ext4: decrypt only the needed block in __ext4_block_zero_page_range()
ext4: decrypt only the needed blocks in ext4_block_write_begin()
ext4: clear BH_Uptodate flag on decryption error
fscrypt: decrypt only the needed blocks in __fscrypt_decrypt_bio()
fscrypt: support decrypting multiple filesystem blocks per page
fscrypt: introduce fscrypt_decrypt_block_inplace()
fscrypt: handle blocksize < PAGE_SIZE in fscrypt_zeroout_range()
fscrypt: support encrypting multiple filesystem blocks per page
fscrypt: introduce fscrypt_encrypt_block_inplace()
fscrypt: clean up some BUG_ON()s in block encryption/decryption
fscrypt: rename fscrypt_do_page_crypto() to fscrypt_crypt_block()
fscrypt: remove the "write" part of struct fscrypt_ctx
fscrypt: simplify bounce page handling
Linus Torvalds [Thu, 11 Jul 2019 03:32:37 +0000 (20:32 -0700)]
Merge tag 'copy-file-range-fixes-1' of git://git./fs/xfs/xfs-linux
Pull copy_file_range updates from Darrick Wong:
"This fixes numerous parameter checking problems and inconsistent
behaviors in the new(ish) copy_file_range system call.
Now the system call will actually check its range parameters
correctly; refuse to copy into files for which the caller does not
have sufficient privileges; update mtime and strip setuid like file
writes are supposed to do; and allows copying up to the EOF of the
source file instead of failing the call like we used to.
Summary:
- Create a generic copy_file_range handler and make individual
filesystems responsible for calling it (i.e. no more assuming that
do_splice_direct will work or is appropriate)
- Refactor copy_file_range and remap_range parameter checking where
they are the same
- Install missing copy_file_range parameter checking(!)
- Remove suid/sgid and update mtime like any other file write
- Change the behavior so that a copy range crossing the source file's
eof will result in a short copy to the source file's eof instead of
EINVAL
- Permit filesystems to decide if they want to handle
cross-superblock copy_file_range in their local handlers"
* tag 'copy-file-range-fixes-1' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
fuse: copy_file_range needs to strip setuid bits and update timestamps
vfs: allow copy_file_range to copy across devices
xfs: use file_modified() helper
vfs: introduce file_modified() helper
vfs: add missing checks to copy_file_range
vfs: remove redundant checks from generic_remap_checks()
vfs: introduce generic_file_rw_checks()
vfs: no fallback for ->copy_file_range
vfs: introduce generic_copy_file_range()
Linus Torvalds [Thu, 11 Jul 2019 03:29:45 +0000 (20:29 -0700)]
Merge tag 'iomap-5.3-merge-1' of git://git./fs/xfs/xfs-linux
Pull iomap updates from Darrick Wong:
"There are a few fixes for gfs2 but otherwise it's pretty quiet so far.
- Only mark inode dirty at the end of writing to a file (instead of
once for every page written).
- Fix for an accounting error in the page_done callback"
* tag 'iomap-5.3-merge-1' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
iomap: fix page_done callback for short writes
fs: fold __generic_write_end back into generic_write_end
iomap: don't mark the inode dirty in iomap_write_end
Linus Torvalds [Thu, 11 Jul 2019 03:27:07 +0000 (20:27 -0700)]
Merge tag 'for_v5.3-rc1' of git://git./linux/kernel/git/jack/linux-fs
Pull ext2, udf and quota updates from Jan Kara:
- some ext2 fixes and cleanups
- a fix of udf bug when extending files
- a fix of quota Q_XGETQSTAT[V] handling
* tag 'for_v5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
udf: Fix incorrect final NOT_ALLOCATED (hole) extent length
ext2: Use kmemdup rather than duplicating its implementation
quota: honor quota type in Q_XGETQSTAT[V] calls
ext2: Always brelse bh on failure in ext2_iget()
ext2: add missing brelse() in ext2_iget()
ext2: Fix a typo in ext2_getattr argument
ext2: fix a typo in comment
ext2: add missing brelse() in ext2_new_inode()
ext2: optimize ext2_xattr_get()
ext2: introduce new helper for xattr entry comparison
ext2: merge xattr next entry check to ext2_xattr_entry_valid()
ext2: code cleanup for ext2_preread_inode()
ext2: code cleanup by using test_opt() and clear_opt()
doc: ext2: update description of quota options for ext2
ext2: Strengthen xattr block checks
ext2: Merge loops in ext2_xattr_set()
ext2: introduce helper for xattr entry validation
ext2: introduce helper for xattr header validation
quota: add dqi_dirty_list description to comment of Dquot List Management
Linus Torvalds [Thu, 11 Jul 2019 03:09:17 +0000 (20:09 -0700)]
Merge tag 'fsnotify_for_v5.3-rc1' of git://git./linux/kernel/git/jack/linux-fs
Pull fsnotify updates from Jan Kara:
"This contains cleanups of the fsnotify name removal hook and also a
patch to disable fanotify permission events for 'proc' filesystem"
* tag 'fsnotify_for_v5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
fsnotify: get rid of fsnotify_nameremove()
fsnotify: move fsnotify_nameremove() hook out of d_delete()
configfs: call fsnotify_rmdir() hook
debugfs: call fsnotify_{unlink,rmdir}() hooks
debugfs: simplify __debugfs_remove_file()
devpts: call fsnotify_unlink() hook
tracefs: call fsnotify_{unlink,rmdir}() hooks
rpc_pipefs: call fsnotify_{unlink,rmdir}() hooks
btrfs: call fsnotify_rmdir() hook
fsnotify: add empty fsnotify_{unlink,rmdir}() hooks
fanotify: Disallow permission events for proc filesystem
Linus Torvalds [Thu, 11 Jul 2019 02:21:38 +0000 (19:21 -0700)]
Merge tag 'locks-v5.3-1' of git://git./linux/kernel/git/jlayton/linux
Pull file locking updates from Jeff Layton:
"Just a couple of small lease-related patches this cycle.
One from Ira to add a new tracepoint that fires during lease conflict
checks, and another patch from Amir to reduce false positives when
checking for lease conflicts"
* tag 'locks-v5.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/jlayton/linux:
locks: eliminate false positive conflicts for write lease
locks: Add trace_leases_conflict
Linus Torvalds [Thu, 11 Jul 2019 01:43:43 +0000 (18:43 -0700)]
Revert "Merge tag 'keys-acl-
20190703' of git://git./linux/kernel/git/dhowells/linux-fs"
This reverts merge
0f75ef6a9cff49ff612f7ce0578bced9d0b38325 (and thus
effectively commits
7a1ade847596 ("keys: Provide KEYCTL_GRANT_PERMISSION")
2e12256b9a76 ("keys: Replace uid/gid/perm permissions checking with an ACL")
that the merge brought in).
It turns out that it breaks booting with an encrypted volume, and Eric
biggers reports that it also breaks the fscrypt tests [1] and loading of
in-kernel X.509 certificates [2].
The root cause of all the breakage is likely the same, but David Howells
is off email so rather than try to work it out it's getting reverted in
order to not impact the rest of the merge window.
[1] https://lore.kernel.org/lkml/
20190710011559.GA7973@sol.localdomain/
[2] https://lore.kernel.org/lkml/
20190710013225.GB7973@sol.localdomain/
Link: https://lore.kernel.org/lkml/CAHk-=wjxoeMJfeBahnWH=9zShKp2bsVy527vo3_y8HfOdhwAAw@mail.gmail.com/
Reported-by: Eric Biggers <ebiggers@kernel.org>
Cc: David Howells <dhowells@redhat.com>
Cc: James Morris <jmorris@namei.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Thomas Gleixner [Wed, 10 Jul 2019 19:42:46 +0000 (21:42 +0200)]
x86/asm: Move native_write_cr0/4() out of line
The pinning of sensitive CR0 and CR4 bits caused a boot crash when loading
the kvm_intel module on a kernel compiled with CONFIG_PARAVIRT=n.
The reason is that the static key which controls the pinning is marked RO
after init. The kvm_intel module contains a CR4 write which requires to
update the static key entry list. That obviously does not work when the key
is in a RO section.
With CONFIG_PARAVIRT enabled this does not happen because the CR4 write
uses the paravirt indirection and the actual write function is built in.
As the key is intended to be immutable after init, move
native_write_cr0/4() out of line.
While at it consolidate the update of the cr4 shadow variable and store the
value right away when the pinning is initialized on a booting CPU. No point
in reading it back 20 instructions later. This allows to confine the static
key and the pinning variable to cpu/common and allows to mark them static.
Fixes:
8dbec27a242c ("x86/asm: Pin sensitive CR0 bits")
Fixes:
873d50d58f67 ("x86/asm: Pin sensitive CR4 bits")
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Reported-by: Xi Ruoyao <xry111@mengyan1223.wang>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Xi Ruoyao <xry111@mengyan1223.wang>
Acked-by: Kees Cook <keescook@chromium.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/alpine.DEB.2.21.1907102140340.1758@nanos.tec.linutronix.de
Arnd Bergmann [Wed, 10 Jul 2019 13:01:53 +0000 (15:01 +0200)]
timekeeping/vsyscall: Use __iter_div_u64_rem()
On 32-bit x86 when building with clang-9, the 'division' loop gets turned
back into an inefficient division that causes a link error:
kernel/time/vsyscall.o: In function `update_vsyscall':
vsyscall.c:(.text+0xe3): undefined reference to `__udivdi3'
Use the existing __iter_div_u64_rem() function which is used to address the
same issue in other places.
Fixes:
44f57d788e7d ("timekeeping: Provide a generic update_vsyscall() implementation")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Tested-by: Nathan Chancellor <natechancellor@gmail.com>
Link: https://lkml.kernel.org/r/20190710130206.1670830-1-arnd@arndb.de
Arnd Bergmann [Wed, 10 Jul 2019 13:04:55 +0000 (15:04 +0200)]
x86/pgtable/32: Fix LOWMEM_PAGES constant
clang points out that the computation of LOWMEM_PAGES causes a signed
integer overflow on 32-bit x86:
arch/x86/kernel/head32.c:83:20: error: signed shift result (0x100000000) requires 34 bits to represent, but 'int' only has 32 bits [-Werror,-Wshift-overflow]
(PAGE_TABLE_SIZE(LOWMEM_PAGES) << PAGE_SHIFT);
^~~~~~~~~~~~
arch/x86/include/asm/pgtable_32.h:109:27: note: expanded from macro 'LOWMEM_PAGES'
#define LOWMEM_PAGES ((((2<<31) - __PAGE_OFFSET) >> PAGE_SHIFT))
~^ ~~
arch/x86/include/asm/pgtable_32.h:98:34: note: expanded from macro 'PAGE_TABLE_SIZE'
#define PAGE_TABLE_SIZE(pages) ((pages) / PTRS_PER_PGD)
Use the _ULL() macro to make it a 64-bit constant.
Fixes:
1e620f9b23e5 ("x86/boot/32: Convert the 32-bit pgtable setup code from assembly to C")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20190710130522.1802800-1-arnd@arndb.de
YueHaibing [Tue, 2 Jul 2019 13:36:31 +0000 (21:36 +0800)]
mmc: sdhci_am654: Add dependency on MMC_SDHCI_AM654
Fix build error:
drivers/mmc/host/sdhci_am654.o: In function `sdhci_am654_probe':
drivers/mmc/host/sdhci_am654.c:464: undefined reference to `__devm_regmap_init_mmio_clk'
drivers/mmc/host/sdhci_am654.o:(.debug_addr+0x3f8): undefined reference to `__devm_regmap_init_mmio_clk'
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes:
aff88ff23512 ("mmc: sdhci_am654: Add Initial Support for AM654 SDHCI driver")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Colin Ian King [Mon, 1 Jul 2019 17:52:46 +0000 (18:52 +0100)]
mmc: alcor: remove a redundant greater or equal to zero comparison
A greater or equal comparison on the unsigned int variable tmp_diff
is always true as unsigned ints are never negative. Hence the
comparison is redundant and can be removed.
Addresses-Coverity: ("Unsigned compared against 0")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Jorge Ramirez-Ortiz [Mon, 1 Jul 2019 15:01:25 +0000 (17:01 +0200)]
mmc: sdhci-msm: fix mutex while in spinlock
mutexes can sleep and therefore should not be taken while holding a
spinlock. move clk_get_rate (can sleep) outside the spinlock protected
region.
Fixes:
83736352e0ca ("mmc: sdhci-msm: Update DLL reset sequence")
Cc: stable@vger.kernel.org
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
YueHaibing [Fri, 28 Jun 2019 04:07:51 +0000 (12:07 +0800)]
mmc: sdhci_am654: Make some symbols static
Fix sparse warnings:
drivers/mmc/host/sdhci_am654.c:192:6: warning: symbol 'sdhci_j721e_4bit_set_clock' was not declared. Should it be static?
drivers/mmc/host/sdhci_am654.c:261:18: warning: symbol 'sdhci_j721e_8bit_ops' was not declared. Should it be static?
drivers/mmc/host/sdhci_am654.c:284:18: warning: symbol 'sdhci_j721e_4bit_ops' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Christoph Hellwig [Tue, 25 Jun 2019 09:20:42 +0000 (11:20 +0200)]
dma-mapping: remove dma_max_pfn
These days, the DMA mapping code must bounce buffers for any unsupported
address. If the driver needs to optimize for natively supported ranges,
then it should use dma_get_required_mask.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Christoph Hellwig [Tue, 25 Jun 2019 09:20:41 +0000 (11:20 +0200)]
mmc: core: let the dma map ops handle bouncing
Just like we do for all other block drivers. Especially as the limit
imposed at the moment might be way to pessimistic for iommus.
This also means we are not going to set a bounce limit for the queue, in
case we have a dma mask. On most architectures it was never needed, the
major hold out was x86-32 with PAE, but that has been fixed by now.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Masahiro Yamada [Mon, 24 Jun 2019 07:03:45 +0000 (16:03 +0900)]
dt-binding: mmc: rename tmio_mmc.txt to renesas,sdhi.txt
As commit
b6147490e6aa ("mmc: tmio: split core functionality, DMA and
MFD glue") said, these MMC controllers use the IP from Panasonic.
TMIO (Toshiba Mobile IO) MMC was the first upstreamed user of this IP.
The common driver code was split and expanded as 'tmio-mmc-core', then
it became historical misnomer since 'tmio' is not the name of this IP.
In the discussion [1], we decide to keep this name as-is at least in
Linux driver level because renaming everything is a big churn.
However, DT should not be oriented to a particular project even though
it is mainly developed in Linux communities.
This is the misfortune only in Linux. Let's stop exporting it to other
projects, where there is no good reason to call this hardware "TMIO".
Rename the file to renesas,sdhi.txt. In fact, all the information in
this file is specific to the Renesas platform.
This commit also removes the first paragraph entirely. The DT-binding
should describe the hardware. It is strange to talk about Linux driver
internals such as how the drivers are probed, how platform data are
handed off, etc.
[1] https://www.spinics.net/lists/linux-mmc/msg46952.html
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Baolin Wang [Fri, 21 Jun 2019 06:12:33 +0000 (14:12 +0800)]
mmc: sdhci-sprd: Add pin control support for voltage switch
For Spreadtrum SD card voltage switching, besides regulator setting,
it also need switch related pin's state to output corresponding voltage.
This patch adds pin control operation to support voltage switch.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Baolin Wang [Fri, 21 Jun 2019 06:12:32 +0000 (14:12 +0800)]
dt-bindings: mmc: sprd: Add pinctrl support
When changing SD card voltage signal for Spreadtrum SD host controller,
it also need to switch related pin's state. Thus add pinctrl properties'
description in documentation.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Baolin Wang [Fri, 21 Jun 2019 06:12:31 +0000 (14:12 +0800)]
mmc: sdhci-sprd: Add start_signal_voltage_switch ops
For Spreadtrum SD host controller, we can not use standard SD registers
to change and detect the I/O voltage signals, since our voltage regulator
for I/O is fixed in hardware, and no signals were connected to the SD
controller. Thus add Spreadtrum specific voltage switch ops to change
voltage instead of using standard SD host registers.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Adrian Hunter [Thu, 20 Jun 2019 09:49:01 +0000 (12:49 +0300)]
mmc: sdhci-pci: Add support for Intel EHL
Add PCI Ids for Intel EHL.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Yoshihiro Shimoda [Wed, 19 Jun 2019 04:55:30 +0000 (13:55 +0900)]
mmc: tmio: Use dma_max_mapping_size() instead of a workaround
Since the commit
133d624b1cee ("dma: Introduce dma_max_mapping_size()")
provides a helper function to get the max mapping size, we can use
the function instead of the workaround code for swiotlb.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Ulf Hansson [Mon, 17 Jun 2019 23:20:50 +0000 (01:20 +0200)]
mmc: sdio: Drop unused in-parameter from mmc_sdio_init_card()
The "powered_resume" in-parameter to mmc_sdio_init_card() has now become
redundant as all callers set it to 0. Therefore let's just drop it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Ulf Hansson [Mon, 17 Jun 2019 23:13:02 +0000 (01:13 +0200)]
mmc: sdio: Drop unused in-parameter to mmc_sdio_reinit_card()
The "powered_resume" in-parameter to mmc_sdio_reinit_card() has now become
redundant as all callers set it to 0. Therefore let's just drop it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Ulf Hansson [Mon, 17 Jun 2019 22:52:59 +0000 (00:52 +0200)]
mmc: sdio: Don't re-initialize powered-on removable SDIO cards at resume
It looks like the original idea behind always doing a re-initialization of
a removable SDIO card during system resume in mmc_sdio_resume(), is to try
to play safe to detect whether the card has been removed.
However, this seems like a really a bad idea as it will most likely screw
things up, especially when the card is expected to remain powered on during
system suspend by the SDIO func driver.
Let's fix this, simply by trusting that the detect work checks if the card
is alive and inserted, which is being scheduled at the PM_POST_SUSPEND
notification anyway.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Ulf Hansson [Mon, 17 Jun 2019 21:51:31 +0000 (23:51 +0200)]
mmc: sdio: Drop powered-on re-init at runtime resume and HW reset
To use the so called powered-on re-initialization of an SDIO card, the
power to the card must obviously have stayed on. If not, the initialization
will simply fail.
In the runtime suspend case, the card is always powered off. Hence, let's
drop the support for powered-on re-initialization during runtime resume, as
it doesn't make sense.
Moreover, during a HW reset, the point is to cut the power to the card and
then do fresh re-initialization. Therefore drop the support for powered-on
re-initialization during HW reset.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fixes:
ca8971ca5753 ("mmc: dw_mmc: Prevent runtime PM suspend when SDIO IRQs are enabled")
Tested-by: Douglas Anderson <dianders@chromium.org>
Ulf Hansson [Mon, 17 Jun 2019 21:41:15 +0000 (23:41 +0200)]
mmc: sdio: Move comment about re-initialization to mmc_sdio_reinit_card()
The comment in mmc_sdio_power_restore() belongs in mmc_sdio_reinit_card(),
which was created during a previous commit that re-factored some code. Fix
this by moving the comment into mmc_sdio_reinit_card().
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Ulf Hansson [Tue, 11 Jun 2019 15:44:32 +0000 (17:44 +0200)]
mmc: sdio: Drop mmc_claim|release_host() in mmc_sdio_power_restore()
The function mmc_sdio_power_restore() is called either from
mmc_sdio_runtime_resume() or from mmc_sdio_hw_reset(). Both callers either
claims/releases the host or require its callers to do so. Therefore let's
drop the redundant calls to mmc_claim|release_host() in
mmc_sdio_power_restore().
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Rafael J. Wysocki [Wed, 10 Jul 2019 09:52:50 +0000 (11:52 +0200)]
Revert "ACPICA: Update table load object initialization"
Revert commit
c522ad0637ca ("ACPICA: Update table load object
initialization") as it causes systems to hang on attempts to load
OEM ACPI tables.
Reported-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Joe Perches [Wed, 10 Jul 2019 05:04:15 +0000 (22:04 -0700)]
clocksource/drivers/npcm: Fix misuse of GENMASK macro
Arguments are supposed to be ordered high then low.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/d6a9d49c9837d38816b71d783f5aed7235e8ca94.1562734889.git.joe@perches.com
Joe Perches [Wed, 10 Jul 2019 05:04:18 +0000 (22:04 -0700)]
irqchip/gic-v3-its: Fix misuse of GENMASK macro
Arguments are supposed to be ordered high then low.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/ab5deb4fc3cd604cb620054770b7d00016d736bc.1562734889.git.joe@perches.com
Steven J. Magnani [Mon, 1 Jul 2019 02:39:35 +0000 (21:39 -0500)]
udf: Fix incorrect final NOT_ALLOCATED (hole) extent length
In some cases, using the 'truncate' command to extend a UDF file results
in a mismatch between the length of the file's extents (specifically, due
to incorrect length of the final NOT_ALLOCATED extent) and the information
(file) length. The discrepancy can prevent other operating systems
(i.e., Windows 10) from opening the file.
Two particular errors have been observed when extending a file:
1. The final extent is larger than it should be, having been rounded up
to a multiple of the block size.
B. The final extent is not shorter than it should be, due to not having
been updated when the file's information length was increased.
[JK: simplified udf_do_extend_final_block(), fixed up some types]
Fixes:
2c948b3f86e5 ("udf: Avoid IO in udf_clear_inode")
CC: stable@vger.kernel.org
Signed-off-by: Steven J. Magnani <steve@digidescorp.com>
Link: https://lore.kernel.org/r/1561948775-5878-1-git-send-email-steve@digidescorp.com
Signed-off-by: Jan Kara <jack@suse.cz>
Nathan Chancellor [Mon, 8 Jul 2019 23:11:55 +0000 (16:11 -0700)]
net/mlx5e: Return in default case statement in tx_post_resync_params
clang warns:
drivers/net/ethernet/mellanox/mlx5/core/en_accel/ktls_tx.c:251:2:
warning: variable 'rec_seq_sz' is used uninitialized whenever switch
default is taken [-Wsometimes-uninitialized]
default:
^~~~~~~
drivers/net/ethernet/mellanox/mlx5/core/en_accel/ktls_tx.c:255:46: note:
uninitialized use occurs here
skip_static_post = !memcmp(rec_seq, &rn_be, rec_seq_sz);
^~~~~~~~~~
drivers/net/ethernet/mellanox/mlx5/core/en_accel/ktls_tx.c:239:16: note:
initialize the variable 'rec_seq_sz' to silence this warning
u16 rec_seq_sz;
^
= 0
1 warning generated.
This case statement was clearly designed to be one that should not be
hit during runtime because of the WARN_ON statement so just return early
to prevent copying uninitialized memory up into rn_be.
Fixes:
d2ead1f360e8 ("net/mlx5e: Add kTLS TX HW offload support")
Link: https://github.com/ClangBuiltLinux/linux/issues/590
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 10 Jul 2019 04:35:08 +0000 (21:35 -0700)]
mlx5: Return -EINVAL when WARN_ON_ONCE triggers in mlx5e_tls_resync().
Return value was changes to 'int' from void but this return statement
was not updated, or it slipped in via a merge.
Fixes:
b5d9a834f4fd ("net/tls: don't clear TX resync flag on error")
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Kosina [Tue, 9 Jul 2019 23:40:23 +0000 (01:40 +0200)]
Merge branch 'for-5.3/uclogic' into for-linus
Jiri Kosina [Tue, 9 Jul 2019 23:39:57 +0000 (01:39 +0200)]
Merge branches 'for-5.2/fixes', 'for-5.3/doc', 'for-5.3/ish', 'for-5.3/logitech' and 'for-5.3/wacom' into for-linus
YueHaibing [Mon, 8 Jul 2019 12:54:08 +0000 (20:54 +0800)]
nfsd: Make __get_nfsdfs_client() static
Fix sparse warning:
fs/nfsd/nfsctl.c:1221:22: warning:
symbol '__get_nfsdfs_client' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
YueHaibing [Mon, 8 Jul 2019 07:29:33 +0000 (15:29 +0800)]
nfsd: Make two functions static
Fix sparse warnings:
fs/nfsd/nfs4state.c:1908:6: warning: symbol 'drop_client' was not declared. Should it be static?
fs/nfsd/nfs4state.c:2518:6: warning: symbol 'force_expire_client' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Jiri Kosina [Tue, 9 Jul 2019 23:20:26 +0000 (01:20 +0200)]
Merge branch 'for-5.3/core' into for-linus
Icenowy Zheng [Sun, 23 Jun 2019 04:37:59 +0000 (12:37 +0800)]
dt-bindings: vendor-prefixes: add Sipeed
Shenzhen Sipeed Technology Co., Ltd. is a company focused on development
kits, which also contains rebranded Lichee Pi series.
Add its vendor prefix binding.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Rob Herring <robh@kernel.org>
Icenowy Zheng [Sun, 23 Jun 2019 04:37:57 +0000 (12:37 +0800)]
dt-bindings: vendor-prefixes: add SoChip
Shenzhen SoChip Technology Co., Ltd. is a hardware vendor that produces
EVBs with Allwinner chips. There's also a SoC named S3 that is developed
by Allwinner (based on Allwinner V3/V3s) but branded SoChip.
Add the vendor prefix for SoChip.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Kefeng Wang [Sat, 22 Jun 2019 03:45:57 +0000 (11:45 +0800)]
dt-bindings: 83xx-512x-pci: Drop cell-index property
28eac2b74cc7 ("powerpc/fsl: Remove cell-index from PCI nodes"),
and for now it is still not used, drop it from doc.
Cc: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Vivien Didelot [Tue, 9 Jul 2019 03:31:13 +0000 (23:31 -0400)]
net: dsa: add support for BRIDGE_MROUTER attribute
This patch adds support for enabling or disabling the flooding of
unknown multicast traffic on the CPU ports, depending on the value
of the switchdev SWITCHDEV_ATTR_ID_BRIDGE_MROUTER attribute.
The current behavior is kept unchanged but a user can now prevent
the CPU conduit to be flooded with a lot of unregistered traffic that
the network stack needs to filter in software with e.g.:
echo 0 > /sys/class/net/br0/multicast_router
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Tue, 9 Jul 2019 21:45:17 +0000 (14:45 -0700)]
pkt_sched: Include const.h
Commit
9903c8dc7342 changed TC_ETF defines to use _BITUL instead of BIT
but did not add the dependecy on linux/const.h. As a consequence,
importing the uapi headers into iproute2 causes builds to fail. Add
the dependency.
Fixes:
9903c8dc7342 ("etf: Don't use BIT() in UAPI headers.")
Cc: Vedang Patel <vedang.patel@intel.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ilias Apalodimas [Tue, 9 Jul 2019 21:14:49 +0000 (00:14 +0300)]
net: netsec: remove static declaration for netsec_set_tx_de()
On commit
ba2b232108d3 ("net: netsec: add XDP support") a static
declaration for netsec_set_tx_de() was added to make the diff easier
to read. Now that the patch is merged let's move the functions around
and get rid of that
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ilias Apalodimas [Tue, 9 Jul 2019 21:14:48 +0000 (00:14 +0300)]
net: netsec: remove superfluous if statement
While freeing tx buffers the memory has to be unmapped if the packet was
an skb or was used for .ndo_xdp_xmit using the same arguments. Get rid
of the unneeded extra 'else if' statement
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 9 Jul 2019 21:38:51 +0000 (14:38 -0700)]
Merge branch 'nf-hw-offload'
Pablo Neira Ayuso says:
====================
netfilter: add hardware offload infrastructure
This patchset adds support for Netfilter hardware offloads.
This patchset reuses the existing block infrastructure, the
netdev_ops->ndo_setup_tc() interface, TC_SETUP_CLSFLOWER classifier and
the flow rule API.
Patch #1 adds flow_block_cb_setup_simple(), most drivers do the same thing
to set up flow blocks, to reduce the number of changes, consolidate
codebase. Use _simple() postfix as requested by Jakub Kicinski.
This new function resides in net/core/flow_offload.c
Patch #2 renames TC_BLOCK_{UN}BIND to FLOW_BLOCK_{UN}BIND.
Patch #3 renames TCF_BLOCK_BINDER_TYPE_* to FLOW_BLOCK_BINDER_TYPE_*.
Patch #4 adds flow_block_cb_alloc() and flow_block_cb_free() helper
functions, this is the first patch of the flow block API.
Patch #5 adds the helper to deal with list operations in the flow block API.
This includes flow_block_cb_lookup(), flow_block_cb_add() and
flow_block_cb_remove().
Patch #6 adds flow_block_cb_priv(), flow_block_cb_incref() and
flow_block_cb_decref() which completes the flow block API.
Patch #7 updates the cls_api to use the flow block API from the new
tcf_block_setup(). This infrastructure transports these objects
via list (through the tc_block_offload object) back to the core
for registration.
CLS_API DRIVER
TC_SETUP_BLOCK ----------> setup flow_block_cb object &
it adds object to flow_block_offload->cb_list
|
CLS_API <-----------------------'
registers list with flow blocks
flow_block_cb & travels back to
calls ->reoffload the core for registration
drivers allocate and sets up (configure the blocks), then
registration happens from the core (cls_api and netfilter).
Patch #8 updates drivers to use the flow block API.
Patch #9 removes the tcf block callback API, which is replaced by the
flow block API.
Patch #10 adds the flow_block_cb_is_busy() helper to check if the block
is already used by a subsystem. This helper is invoked from
drivers. Once drivers are updated to support for multiple
subsystems, they can remove this check.
Patch #11 rename tc structure and definitions for the block bind/unbind
path.
Patch #12 introduces basic netfilter hardware offload infrastructure
for the ingress chain. This includes 5-tuple exact matching
and accept / drop rule actions. Only basechains are supported
at this stage, no .reoffload callback is implemented either.
Default policy to "accept" is only supported for now.
table netdev filter {
chain ingress {
type filter hook ingress device eth0 priority 0; flags offload;
ip daddr 192.168.0.10 tcp dport 22 drop
}
}
This patchset reuses the existing tcf block callback API and it places it
in the flow block callback API in net/core/flow_offload.c.
This series aims to address Jakub and Jiri's feedback, please see specific
patches in this batch for changelog in this v4.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso [Tue, 9 Jul 2019 21:00:43 +0000 (23:00 +0200)]
netfilter: nf_tables: add hardware offload support
This patch adds hardware offload support for nftables through the
existing netdev_ops->ndo_setup_tc() interface, the TC_SETUP_CLSFLOWER
classifier and the flow rule API. This hardware offload support is
available for the NFPROTO_NETDEV family and the ingress hook.
Each nftables expression has a new ->offload interface, that is used to
populate the flow rule object that is attached to the transaction
object.
There is a new per-table NFT_TABLE_F_HW flag, that is set on to offload
an entire table, including all of its chains.
This patch supports for basic metadata (layer 3 and 4 protocol numbers),
5-tuple payload matching and the accept/drop actions; this also includes
basechain hardware offload only.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso [Tue, 9 Jul 2019 20:55:49 +0000 (22:55 +0200)]
net: flow_offload: rename tc_cls_flower_offload to flow_cls_offload
And any other existing fields in this structure that refer to tc.
Specifically:
* tc_cls_flower_offload_flow_rule() to flow_cls_offload_flow_rule().
* TC_CLSFLOWER_* to FLOW_CLS_*.
* tc_cls_common_offload to tc_cls_common_offload.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso [Tue, 9 Jul 2019 20:55:48 +0000 (22:55 +0200)]
net: flow_offload: add flow_block_cb_is_busy() and use it
This patch adds a function to check if flow block callback is already in
use. Call this new function from flow_block_cb_setup_simple() and from
drivers.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso [Tue, 9 Jul 2019 20:55:47 +0000 (22:55 +0200)]
net: sched: remove tcf block API
Unused, now replaced by flow block API.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso [Tue, 9 Jul 2019 20:55:46 +0000 (22:55 +0200)]
drivers: net: use flow block API
This patch updates flow_block_cb_setup_simple() to use the flow block API.
Several drivers are also adjusted to use it.
This patch introduces the per-driver list of flow blocks to account for
blocks that are already in use.
Remove tc_block_offload alias.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso [Tue, 9 Jul 2019 20:55:45 +0000 (22:55 +0200)]
net: sched: use flow block API
This patch adds tcf_block_setup() which uses the flow block API.
This infrastructure takes the flow block callbacks coming from the
driver and register/unregister to/from the cls_api core.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso [Tue, 9 Jul 2019 20:55:44 +0000 (22:55 +0200)]
net: flow_offload: add flow_block_cb_{priv, incref, decref}()
This patch completes the flow block API to introduce:
* flow_block_cb_priv() to access callback private data.
* flow_block_cb_incref() to bump reference counter on this flow block.
* flow_block_cb_decref() to decrement the reference counter.
These functions are taken from the existing tcf_block_cb_priv(),
tcf_block_cb_incref() and tcf_block_cb_decref().
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso [Tue, 9 Jul 2019 20:55:43 +0000 (22:55 +0200)]
net: flow_offload: add list handling functions
This patch adds the list handling functions for the flow block API:
* flow_block_cb_lookup() allows drivers to look up for existing flow blocks.
* flow_block_cb_add() adds a flow block to the per driver list to be registered
by the core.
* flow_block_cb_remove() to remove a flow block from the list of existing
flow blocks per driver and to request the core to unregister this.
The flow block API also annotates the netns this flow block belongs to.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso [Tue, 9 Jul 2019 20:55:42 +0000 (22:55 +0200)]
net: flow_offload: add flow_block_cb_alloc() and flow_block_cb_free()
Add a new helper function to allocate flow_block_cb objects.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso [Tue, 9 Jul 2019 20:55:41 +0000 (22:55 +0200)]
net: flow_offload: rename TCF_BLOCK_BINDER_TYPE_* to FLOW_BLOCK_BINDER_TYPE_*
Rename from TCF_BLOCK_BINDER_TYPE_* to FLOW_BLOCK_BINDER_TYPE_* and
remove temporary tcf_block_binder_type alias.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso [Tue, 9 Jul 2019 20:55:40 +0000 (22:55 +0200)]
net: flow_offload: rename TC_BLOCK_{UN}BIND to FLOW_BLOCK_{UN}BIND
Rename from TC_BLOCK_{UN}BIND to FLOW_BLOCK_{UN}BIND and remove
temporary tc_block_command alias.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso [Tue, 9 Jul 2019 20:55:39 +0000 (22:55 +0200)]
net: flow_offload: add flow_block_cb_setup_simple()
Most drivers do the same thing to set up the flow block callbacks, this
patch adds a helper function to do this.
This preparation patch reduces the number of changes to adapt the
existing drivers to use the flow block callback API.
This new helper function takes a flow block list per-driver, which is
set to NULL until this driver list is used.
This patch also introduces the flow_block_command and
flow_block_binder_type enumerations, which are renamed to use
FLOW_BLOCK_* in follow up patches.
There are three definitions (aliases) in order to reduce the number of
updates in this patch, which go away once drivers are fully adapted to
use this flow block API.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 9 Jul 2019 21:29:27 +0000 (14:29 -0700)]
Merge branch 'net-hisilicon-Add-support-for-HI13X1-to-hip04_eth'
Jiangfeng Xiao says:
====================
net: hisilicon: Add support for HI13X1 to hip04_eth
The main purpose of this patch series is to extend the
hip04_eth driver to support HI13X1_GMAC.
The offset and bitmap of some registers of HI13X1_GMAC
are different from hip04_eth common soc. In addition,
the definition of send descriptor and parsing descriptor
are different from hip04_eth common soc. So the macro
of the register offset is redefined to adapt the HI13X1_GMAC.
Clean up the sparse warning by the way.
Change since v1:
* Add a cover letter.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiangfeng Xiao [Tue, 9 Jul 2019 03:31:11 +0000 (11:31 +0800)]
net: hisilicon: Add an tx_desc to adapt HI13X1_GMAC
HI13X1 changed the offsets and bitmaps for tx_desc
registers in the same peripheral device on different
models of the hip04_eth.
Signed-off-by: Jiangfeng Xiao <xiaojiangfeng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiangfeng Xiao [Tue, 9 Jul 2019 03:31:10 +0000 (11:31 +0800)]
net: hisilicon: Add an rx_desc to adapt HI13X1_GMAC
HI13X1 changed the offsets and bitmaps for rx_desc
registers in the same peripheral device on different
models of the hip04_eth.
Signed-off-by: Jiangfeng Xiao <xiaojiangfeng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiangfeng Xiao [Tue, 9 Jul 2019 03:31:09 +0000 (11:31 +0800)]
net: hisilicon: Offset buf address to adapt HI13X1_GMAC
The buf unit size of HI13X1_GMAC is cache_line_size,
which is 64, so the address we write to the buf register
needs to be shifted right by 6 bits.
The 31st bit of the PPE_CFG_CPU_ADD_ADDR register
of HI13X1_GMAC indicates whether to release the buffer
of the message, and the low indicates that it is valid.
Signed-off-by: Jiangfeng Xiao <xiaojiangfeng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiangfeng Xiao [Tue, 9 Jul 2019 03:31:08 +0000 (11:31 +0800)]
net: hisilicon: Add group field to adapt HI13X1_GMAC
In general, group is the same as the port, but some
boards specify a special group for better load
balancing of each processing unit.
Signed-off-by: Jiangfeng Xiao <xiaojiangfeng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiangfeng Xiao [Tue, 9 Jul 2019 03:31:07 +0000 (11:31 +0800)]
net: hisilicon: dt-bindings: Add an field of port-handle
In general, group is the same as the port, but some
boards specify a special group for better load
balancing of each processing unit.
Signed-off-by: Jiangfeng Xiao <xiaojiangfeng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiangfeng Xiao [Tue, 9 Jul 2019 03:31:06 +0000 (11:31 +0800)]
net: hisilicon: HI13X1_GMAX need dreq reset at first
HI13X1_GMAC delete request for soft reset at first,
otherwise, the subsequent initialization will not
take effect.
Signed-off-by: Jiangfeng Xiao <xiaojiangfeng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiangfeng Xiao [Tue, 9 Jul 2019 03:31:05 +0000 (11:31 +0800)]
net: hisilicon: HI13X1_GMAX skip write LOCAL_PAGE_REG
HI13X1_GMAC changed the offsets and bitmaps for
GE_TX_LOCAL_PAGE_REG registers in the same peripheral
device on different models of the hip04_eth. With the
default configuration, HI13X1_GMAC can also work without
any writes to the GE_TX_LOCAL_PAGE_REG register.
Signed-off-by: Jiangfeng Xiao <xiaojiangfeng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>