ARM: at91: smc: bug fix in sam9_smc_cs_read()

commit 1588c51cf6d782e63a8719681d905ef0ac22ee62 upstream.

There was a copy/paste error when reading the nwe_pulse value.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@traphandler.com>
Acked-by: Boris BREZILLON <b.brezillon@overkiz.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARM: at91: at91sam9g45: set default mmc pinctrl-names

commit 0645b93f6c223b594c0dca348e2ae0a23bccf6e3 upstream.

pinctrl-names property was missing from mmc nodes.

Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty/serial: at91: disable uart timer at start of shutdown

commit 8bc661bfc0c2d221e209f4205bdaaf574d50100c upstream.

The uart timer will schedule a tasklet when it fires. It is possible that it
can fire inside _shutdown before it is killed in the dma and pdc cleanup
routines. This causes a tasklet that exists after the port is shutdown, so when
the kernel finally executes it, it panics as the tty port is NULL.

This is a somewhat rare condition but its possible if a program keeps on
opening/closing the port. It has been observed in particular with systemd
boot messages that were causing a kernel panic because of this behavior.

Moving the timer deletion to the beginning of the function stops a tasklet from
being scheduled unexpectedly.

Signed-off-by: Marek Roszko <mark.roszko@gmail.com>
[nicolas.ferre@atmel.com: modify commit message, call setup_timer() in any case]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty/serial: at91: reset rx_ring when port is shutdown

commit bb7e73c598fb226c75f7625088a8f6a45a0fc892 upstream.

When using RX DMA, the driver won't pass any data to the uart layer
until the buffer is flipped. When the port is shutdown, the dma buffers
are unmapped, but the head and tail of the ring buffer are not reseted.
Since the serial console will keep the port open, this will only
present itself when the uart is not shared.

To reproduce the issue, with an unpatched driver, run a getty on /dev/ttyS0
with no serial console and exit. Getty will exit, and when the new one returns
you will be unable to log in.  If you hold down a key long enough to fill the
DMA buffer and flip it, you can then log in.

Signed-off-by: Mark Deneen <mdeneen@gmail.com>
Acked-by: Leilei Zhao <leilei.zhao@atmel.com>
[nicolas.ferre@atmel.com: adapt to mainline kernel, handle !DMA case]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty/serial: at91: fix race condition in atmel_serial_remove

commit f50c995f9ebf064cea1368bf361c4e29679415b4 upstream.

The _remove callback could be called when a tasklet is scheduled. tasklet_kill
was called inside the function in order to free up any scheduled tasklets.
However it was called after uart_remove_one_port which destroys tty references
needed in the port for atmel_tasklet_func.
Simply putting the tasklet_kill at the start of the function will prevent this
conflict.

Signed-off-by: Marek Roszko <mark.roszko@gmail.com>
Acked-by: Leilei Zhao <leilei.zhao@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty/serial: at91: Handle shutdown more safely

commit 0cc7c6c7916b1b6f34350ff1473b80b9f7e459c0 upstream.

Interrupts were being cleaned up late in the shutdown handler, it is possible
that an interrupt can occur and schedule a tasklet that runs after the port is
cleaned up. There is a null dereference due to this race condition with the
following stacktrace:

[<c02092b0>] (atmel_tasklet_func+0x514/0x814) from [<c001fd34>] (tasklet_action+0x70/0xa8)
[<c001fd34>] (tasklet_action+0x70/0xa8) from [<c001f60c>] (__do_softirq+0x90/0x144)
[<c001f60c>] (__do_softirq+0x90/0x144) from [<c001fa18>] (irq_exit+0x40/0x4c)
[<c001fa18>] (irq_exit+0x40/0x4c) from [<c000e298>] (handle_IRQ+0x64/0x84)
[<c000e298>] (handle_IRQ+0x64/0x84) from [<c000d6c0>] (__irq_svc+0x40/0x50)
[<c000d6c0>] (__irq_svc+0x40/0x50) from [<c0208060>] (atmel_rx_dma_release+0x88/0xb8)
[<c0208060>] (atmel_rx_dma_release+0x88/0xb8) from [<c0209740>] (atmel_shutdown+0x104/0x160)
[<c0209740>] (atmel_shutdown+0x104/0x160) from [<c0205e8c>] (uart_port_shutdown+0x2c/0x38)

Signed-off-by: Marek Roszko <mark.roszko@gmail.com>
Acked-by: Leilei Zhao <leilei.zhao@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mei: use hbm idle state to prevent spurious resets

commit 66ae460b13c31a176b41550259683c841a62af3e upstream.

When reset is caused by hbm protocol mismatch or timeout
we might end up in an endless reset loop and hbm protocol
will never sync

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: vt6656: CARDqGetNextTBTT correct uLowNextTBTT

commit 9acec059c0cef0bf086c738f4c0b1f4447782a48 upstream.

value uLowNextTBTT yields wrong value.

ULL is needed with qwTSF

Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: vt6656: [BUG] BBvUpdatePreEDThreshold Always set sensitivity on bScanning

commit 8f248dae133668bfb8e9379b4b3f0571c858b24a upstream.

byBBPreEDIndex value is initially 0, this means that from
cold BBvUpdatePreEDThreshold is never set.

This means that sensitivity may be in an ambiguous state,
failing to scan any wireless points or at least distant ones.

Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: r8712u: Set device type to wlan

commit 3a21f00a5002b14e4aab52aef59d33ed28468a13 upstream.

The latest version of NetworkManager does not recognize the device as wireless
without this change.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging/lustre/ptlrpc: Fix a crash when dereferencing NULL pointer

commit 3c92a0bf4d72737035a16c4fe357ccd439c9b7d2 upstream.

When a system runs out of memory and the function
ptlrpc_register_bulk() is called from ptl_send_rpc() the call to
LNetMEAttach() fails due to failure to allocate memory.  This forces
the code into an error path, which most probably previously went
untested.  The error path:
if (rc != 0) {
        CERROR("%s: LNetMEAttach failed x"LPU64"/%d: rc = %dn",
                desc->bd_export->exp_obd->obd_name, xid,
                posted_md, rc);
        break;
}
This print assumes that desc->bd_export is not NULL.  However, it is.
In fact it is expected to be NULL.  desc->bd_import is the correct
structure to access in this case.

Lustre-change: http://review.whamcloud.com/7121
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-3585
Signed-off-by: Amir Shehata <amir.shehata@intel.com>
Reviewed-by: Liang Zhen <liang.zhen@intel.com>
Reviewed-by: Doug Oucharek <doug.s.oucharek@intel.com>
Reviewed-by: Oleg Drokin <oleg.drokin@intel.com>
Signed-off-by: Peng Tao <bergwolf@gmail.com>
Signed-off-by: Andreas Dilger <andreas.dilger@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ath9k: Disable cross-band FCC

commit 1e2f9295f4c657500111514f92a3d3894d0e05b4 upstream.

Fast Channel Change across bands was enabled for
AR9462 recently, but this is causing baseband issues.
Disable it until this feature is tested well. Also,
remove the feature bit for AR9565 since it is
a single-band card and doesn't support this feature.

Reported-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ath9k: Use correct channel for RX packets

commit ff9a93f2ebb88ac7aab9568de80b64b92078e96d upstream.

Accessing the current channel definition in mac80211
when processing RX packets is problematic because it
could have been updated when a scan is issued. Since a
channel change involves flushing the existing packets
in the RX queue before a chip-reset is done, they would
be processed using the wrong band/channel information.

To avoid this, use the current channel information
maintained in the driver.

Reported-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

b43: fix the wrong assignment of status.freq in b43_rx()

commit 64e5acb09ca6b50c97299cff9ef51299470b29f2 upstream.

Use the right function to update frequency value.

If rx skb is probe response or beacon, the wrong frequency value can
cause problem that bss info can't be updated when it should be.

Fixes: 8318d78a44d4 ("cfg80211 API for channels/bitrates, mac80211 and driver conversion")
Signed-off-by: ZHAO Gang <gamerh2o@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

b43legacy: Fix unload oops if firmware is not available

commit 452028665312672c6ba9e16a19248ee00ead9400 upstream.

The asyncronous firmware load uses a completion struct to hold firmware
processing until the user-space routines are up and running. There is.
however, a problem in that the waiter is nevered canceled during teardown.
As a result, unloading the driver when firmware is not available causes an oops.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

b43: Fix unload oops if firmware is not available

commit 0673effd41dba323d6a280ef37b5ef29f3f5a653 upstream.

The asyncronous firmware load uses a completion struct to hold firmware
processing until the user-space routines are up and running. There is.
however, a problem in that the waiter is nevered canceled during teardown.
As a result, unloading the driver when firmware is not available causes an oops.

To be able to access the completion structure at teardown, it had to be moved
into the b43_wldev structure.

This patch also fixes a typo in a comment.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

b43: Fix lockdep splat

commit 09164043f63c947a49797750a09ca1cd7c31108e upstream.

In https://bugzilla.kernel.org/show_bug.cgi?id=67561, a locking dependency is reported
when b43 is used with hostapd, and rfkill is used to kill the radio output.

The lockdep splat (in part) is as follows:

======================================================
[ INFO: possible circular locking dependency detected ]
3.12.0 #1 Not tainted
-------------------------------------------------------
rfkill/10040 is trying to acquire lock:
 (rtnl_mutex){+.+.+.}, at: [<ffffffff8146f282>] rtnl_lock+0x12/0x20

but task is already holding lock:
 (rfkill_global_mutex){+.+.+.}, at: [<ffffffffa04832ca>] rfkill_fop_write+0x6a/0x170 [rfkill]

--snip--

Chain exists of:
  rtnl_mutex --> misc_mtx --> rfkill_global_mutex

The fix is to move the initialization of the hardware random number generator
outside the code range covered by the rtnl_mutex.

Reported-by: yury <urykhy@gmail.com>
Tested-by: yury <urykhy@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iwlwifi: mvm: fix missing cleanup in .start() error path

commit 91b0d1198417cf4fd9a7bd4138b6909f0b359099 upstream.

Cleanup of iwl_mvm_leds was missing in case of error,
resulting in the following warning:

WARNING: at lib/kobject.c:196 kobject_add_internal+0x1f4/0x210()
kobject_add_internal failed for phy0-led with -EEXIST, don't try to register things with the same name in the same directory.

which prevents further reloads of the driver.

Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iwlwifi: pcie: enable oscillator for L1 exit

commit 2d93aee152b1758a94a18fe15d72153ba73b5679 upstream.

Enabling the oscillator consumes slightly more power (100uA)
but allows to make sure that we exit from L1 on time.

Not doing so might lead to a PCIe specification violation
since we might wake up from L1 at the wrong time.
This issue has been identified on 3160 and 7260 only.
On older NICs L1 off is not enabled, on newer NICs (7265),
the issue is fixed.

When the bug occurs the user sees that the NIC has
disappeared from the PCI bridge, any access to the device
returns 0xff.

This fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=64541

and has been extensively discussed here:
http://markmail.org/thread/mfmpzqt3r333n4bo

Fixes: 99cd47142399 ("iwlwifi: add 7000 series device configuration")
Reported-and-tested-by: wzyboy <wzyboy@wzyboy.org>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mwifiex: fix wrong 11ac bits setting in fw_cap_info

commit 1e202242ee1432d68a8bea4919b2ae0ef19d9e06 upstream.

bit 14 is actually reserved and bit 12 & 13 should be used for
11ac capability in fw_cap_info.

Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mwifiex: add missing endian conversion for fw_tsf

commit 9795229752c31da0c5f8a7dc4c827665327b52f9 upstream.

It is u64 data received from firmware. Little endian to cpu
conversion is required here.

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rtlwifi: rtl8188ee: Fix typo in code

commit f699273d6a624266ebc9198774f06ee64a3847a1 upstream.

The static analyser "cppcheck" shows the following typo:
drivers/net/wireless/rtlwifi/rtl8188ee/dm.c:1081]: (style) Same expression on both sides of '!='.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Reported-by: David Binderman <dcb314@hotmail.com>
Cc: David Binderman <dcb314@hotmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rtlwifi: Add missing code to PWDB statics routine

commit d82403a9f407217b6aed5260aa92a120e8e98310 upstream.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rtlwifi: rtl8192cu: Fix some code in RF handling

commit e9b0784bb9de3152e787ee779868c626b137fb3b upstream.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rtlwifi: rtl8192cu: Update the power index registers

commit 9806eacf5de27ab01d680c5d75c92a3a89734e4f upstream.

This patch uses the newly introduced power index register routines.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rtlwifi: rtl8192c: Add routines to save/restore power index registers

commit 97204e93f01868eeba6ae5c4f3270f32905bb418 upstream.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rtlwifi: Increase the RX queue length for USB drivers

commit dc6405712268fe514d3dd89aa936c4397b0871b9 upstream.

The current number of RX buffers queued is 32, which is too small under
heavy load. That number is doubled.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rtlwifi: rtl8192c: Add new definitions in the dm_common header

commit c908c74e005de780fddbe8cb6fcd44803f5d4b74 upstream.

Changes in the gain-control mechanism will require some changes in the header.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rtlwifi: Set the link state

commit 619ce76f8bb850b57032501a39f26aa6c6731c70 upstream.

The present code fails to set the linked state when an interface is
added.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rtlwifi: Redo register save locations

commit b9a758a8c905fc59e783ae91ad645452d877ea88 upstream.

The initial USB driver did not use some register save locations in the
private data storage. To save some memory, a union was used to overlay these
variables with USB I/O components. In an update of the gain-control code,
these register save locations are now needed for USB drivers.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rtlwifi: rtl8192cu: Add new firmware

commit 62009b7f12793c932aaba0df946b04cb4a77d022 upstream.

Vendor driver rtl8188C_8192C_8192D_usb_linux_v3.4.2_3727.20120404 introduced
new firmware for these chips. The code try for the new file, and fall back to
the original firmware if the new file is not available.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rtlwifi: rtl8192c: Prevent reconnect attempts if not connected

commit 8fd77aec1a9d6f4328fc0244f21932114e066df3 upstream.

This driver has a watchdog timer that attempts to reconnect when beacon frames
are not seen for 6 seconds. This patch disables that reconnect whenever the
device has never been connected.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rtlwifi: Update beacon statistics for USB driver

commit 65b9cc97c6852fae19dc5c7745e9abc8dd380aad upstream.

The USB drivers were not updating the beacon statistics, which led to
false beacon loss indications.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rtlwifi: rtl8192cu: Add new device ID

commit f87f960b2fb802f26ee3b00c19320e57a9c583ff upstream.

Reported-by: Jan Prinsloo <janroot@gmail.com>
Tested-by: Jan Prinsloo <janroot@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: ehci: add freescale imx28 special write register method

commit feffe09f510c475df082546815f9e4a573f6a233 upstream.

According to Freescale imx28 Errata, "ENGR119653 USB: ARM to USB
register error issue", All USB register write operations must
use the ARM SWP instruction. So, we implement a special ehci_write
for imx28.

Discussion for it at below:
http://marc.info/?l=linux-usb&m=137996395529294&w=2

Without this patcheset, imx28 works unstable at high AHB bus loading.
If the bus loading is not high, the imx28 usb can work well at the most
of time. There is a IC errata for this problem, usually, we consider
IC errata is a problem not a new feature, and this workaround is needed
for that, so we need to add them to stable tree 3.11+.

Cc: robert.hodaszi@digi.com
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Tested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: fix race between hub_disconnect and recursively_mark_NOTATTACHED

commit 543d7784b07ffd16cc82a9cb4e1e0323fd0040f1 upstream.

There is a race in the hub driver between hub_disconnect() and
recursively_mark_NOTATTACHED().  This race can be triggered if the
driver is unbound from a device at the same time as the bus's root hub
is removed.  When the race occurs, it can cause an oops:

BUG: unable to handle kernel NULL pointer dereference at 0000015c
IP: [<c16d5fb0>] recursively_mark_NOTATTACHED+0x20/0x60
Call Trace:
 [<c16d5fc4>] recursively_mark_NOTATTACHED+0x34/0x60
 [<c16d5fc4>] recursively_mark_NOTATTACHED+0x34/0x60
 [<c16d5fc4>] recursively_mark_NOTATTACHED+0x34/0x60
 [<c16d5fc4>] recursively_mark_NOTATTACHED+0x34/0x60
 [<c16d6082>] usb_set_device_state+0x92/0x120
 [<c16d862b>] usb_disconnect+0x2b/0x1a0
 [<c16dd4c0>] usb_remove_hcd+0xb0/0x160
 [<c19ca846>] ? _raw_spin_unlock_irqrestore+0x26/0x50
 [<c1704efc>] ehci_mid_remove+0x1c/0x30
 [<c1704f26>] ehci_mid_stop_host+0x16/0x30
 [<c16f7698>] penwell_otg_work+0xd28/0x3520
 [<c19c945b>] ? __schedule+0x39b/0x7f0
 [<c19cdb9d>] ? sub_preempt_count+0x3d/0x50
 [<c125e97d>] process_one_work+0x11d/0x3d0
 [<c19c7f4d>] ? mutex_unlock+0xd/0x10
 [<c125e0e5>] ? manage_workers.isra.24+0x1b5/0x270
 [<c125f009>] worker_thread+0xf9/0x320
 [<c19ca846>] ? _raw_spin_unlock_irqrestore+0x26/0x50
 [<c125ef10>] ? rescuer_thread+0x2b0/0x2b0
 [<c1264ac4>] kthread+0x94/0xa0
 [<c19d0f77>] ret_from_kernel_thread+0x1b/0x28
 [<c1264a30>] ? kthread_create_on_node+0xc0/0xc0

One problem is that recursively_mark_NOTATTACHED() uses the intfdata
value and hub->hdev->maxchild while hub_disconnect() is clearing them.
Another problem is that it uses hub->ports[i] while the port device is
being released.

To fix this race, we need to hold the device_state_lock while
hub_disconnect() changes the values.  (Note that usb_disconnect()
and hub_port_connect_change() already acquire this lock at similar
critical times during a USB device's life cycle.)  We also need to
remove the port devices after maxchild has been set to 0, instead of
before.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: "Du, Changbin" <changbinx.du@intel.com>
Tested-by: "Du, Changbin" <changbinx.du@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: xhci: Check for XHCI_PLAT in xhci_cleanup_msix()

commit 9005355af23856c55a5538c9024355785424821b upstream.

If CONFIG_PCI is enabled, make sure xhci_cleanup_msix()
doesn't try to free a bogus PCI IRQ or dereference an invalid
pci_dev when the xHCI device is actually a platform_device.

This patch should be backported to kernels as old as 3.9, that
contain the commit 52fb61250a7a132b0cfb9f4a1060a1f3c49e5a25
"xhci-plat: Don't enable legacy PCI interrupts."

Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: Nokia 502 is an unusual device

commit 0e16114f2db4838251fb64f3b550996ad3585890 upstream.

The USB storage operation of Nokia Asha 502 Dual SIM smartphone running Asha
Platform 1.1.1 is unreliable in respect of data consistency (i.e. transfered
files are corrupted). A similar issue is described here:
http://discussions.nokia.com/t5/Asha-and-other-Nokia-Series-30/Nokia-301-USB-transfers-and-corrupted-files/td-p/1974170

The workaround is (MAX_SECTORS_64):
   rmmod usb_storage && modprobe usb_storage quirks=0421:06aa:m

The patch adds the tested device to the unusual list permanently.

Signed-off-by: Mikhail Zolotaryov <lebon@lebon.org.ua>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: ftdi_sio: added CS5 quirk for broken smartcard readers

commit c1f15196ac3b541d084dc80a8fbd8a74c6a0bd44 upstream.

Genuine FTDI chips support only CS7/8. A previous fix in commit
8704211f65a2 ("USB: ftdi_sio: fixed handling of unsupported CSIZE
setting") enforced this limitation and reported it back to userspace.

However, certain types of smartcard readers depend on specific
driver behaviour that requests 0 data bits (not 5) to change into a
different operating mode if CS5 has been set.

This patch reenables this behaviour for all FTDI devices.

Tagged to be added to stable, because it affects a lot of users of
embedded systems which rely on these readers to work properly.

Reported-by: Heinrich Siebmanns <H.Siebmanns@t-online.de>
Tested-by: Heinrich Siebmanns <H.Siebmanns@t-online.de>
Signed-off-by: Colin Leitner <colin.leitner@gmail.com>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: cypress_m8: fix ring-indicator detection and reporting

commit 440ebadeae9298d7de3d4d105342691841ec88d0 upstream.

Fix ring-indicator (RI) status-bit definition, which was defined as CTS,
effectively preventing RI-changes from being detected while reporting
false RI status.

This bug predates git.

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: serial: add support for iBall 3.5G connect usb modem

commit 7d5c1b9c7cb5ec8e52b1adc65c484a923a8ea6c3 upstream.

Add support for iBall 3.5G connect usb modem.

$lsusb
Bus 002 Device 006: ID 1c9e:9605 OMEGA TECHNOLOGY

$usb-devices
T:  Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  6 Spd=480 MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=1c9e ProdID=9605 Rev=00.00
S:  Manufacturer=USB Modem
S:  Product=USB Modem
S:  SerialNumber=1234567890ABCDEF
C:  #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA
I:  If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I:  If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I:  If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I:  If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I:  If#= 4 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage

Signed-off-by: Rahul Bedarkar <rahulbedarkar89@gmail.com>
Suggested-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: option: add new zte 3g modem pids to option driver

commit 4d90b819ae4c7ea8fd5e2bb7edc68c0f334be2e4 upstream.

Signed-off-by: Jun zhang <zhang.jun92@zte.com.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: pl2303: fix data corruption on termios updates

commit 623c8263376c0b8a4b0c220232e7313d762cd0cc upstream.

Some PL2303 devices are known to lose bytes if you change serial
settings even to the same values as before. Avoid this by comparing the
encoded settings with the previsouly used ones before configuring the
device.

The common case was fixed by commit bf5e5834bffc6 ("pl2303: Fix mode
switching regression"), but this problem was still possible to trigger,
for instance, by using the TCSETS2-interface to repeatedly request
115201 baud, which gets mapped to 115200 and thus always triggers a
settings update.

Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: chipidea: udc: using MultO at TD as real mult value for ISO-TX

commit 2fc5a7dace3c43e62402ab4e8800a8f1834ffe2a upstream.

We have met a bug that the high bandwidth ISO-TX transfer has failed
at the last packet if it is less than 1024, the TD status shows it
is "Transaction Error".

The root cause of this problem is: the mult value at qh is not correct
for current TD's transfer length. We use TD list to queue un-transfer
TDs, and change mult for new adding TDs. If new adding TDs transfer length
less than 1024, but the queued un-transfer TDs transfer length is larger
than 1024, the transfer error will occur, and vice versa.
Usually, this problem occurs at the last packet, and the first packet for
new frame.

We fixed this problem by setting Mult at QH as the largest value (3), and
set MultO (Multiplier Override) at TD according to every transfer length.
It can cover both hardware version less than 2.3 (the real mult is MultO
if it is not 0) and 2.3+ (the real mult is min(qh.mult, td.multo)).

Since the MultO bits are only existed at TX TD, we keep the ISO-RX behavior
unchanged.

For stable tree: 3.11+.

Cc: Michael Grzeschik <m.grzeschik@pengutronix.de>
Reported-by: Matthieu Vanin <b47495@freescale.com>
Tested-by: Matthieu Vanin <b47495@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: chipidea: need to mask INT_STATUS when write otgsc

commit 5332ff1fb63c46588656e4208201bc131627c878 upstream.

For otgsc, both enable bits and status bits are in it. So we need
to make sure the status bits are not be cleared when write enable
bits. It can fix one bug that we plug in/out Micro AB cable fast,
and sometimes, the IDIS will be cleared wrongly when handle last
ID interrupt (ID 0->1), so the current interrupt will not occur.

For stable tree: 3.12+

Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: chipidea: imx: set CI_HDRC_IMX28_WRITE_FIX for imx28

commit 1071055e2a118a81c0b300d7f4af7eba3f7a7c82 upstream.

Due to imx28 needs ARM swp instruction for writing, we set
CI_HDRC_IMX28_WRITE_FIX for imx28.

This patch is needed for stable tree 3.11+

Cc: robert.hodaszi@digi.com
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Tested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: chipidea: add freescale imx28 special write register method

commit ed8f8318d2ef3e5f9e4ddf79349508c116b68d7f upstream.

According to Freescale imx28 Errata, "ENGR119653 USB: ARM to USB
register error issue", All USB register write operations must
use the ARM SWP instruction. So, we implement special hw_write
and hw_test_and_clear for imx28.

Discussion for it at below:
http://marc.info/?l=linux-usb&m=137996395529294&w=2

This patch is needed for stable tree 3.11+.

Cc: robert.hodaszi@digi.com
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Tested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

x86, kvm: correctly access the KVM_CPUID_FEATURES leaf at 0x40000101

commit 77f01bdfa5e55dc19d3eb747181d2730a9bb3ca8 upstream.

When Hyper-V hypervisor leaves are present, KVM must relocate
its own leaves at 0x40000100, because Windows does not look for
Hyper-V leaves at indices other than 0x40000000.  In this case,
the KVM features are at 0x40000101, but the old code would always
look at 0x40000001.

Fix by using kvm_cpuid_base().  This also requires making the
function non-inline, since kvm_cpuid_base() is static.

Fixes: 1085ba7f552d84aa8ac0ae903fa8d0cc2ff9f79d
Cc: mtosatti@redhat.com
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

x86, kvm: cache the base of the KVM cpuid leaves

commit 1c300a40772dae829b91dad634999a6a522c0829 upstream.

It is unnecessary to go through hypervisor_cpuid_base every time
a leaf is found (which will be every time a feature is requested
after the next patch).

Fixes: 1085ba7f552d84aa8ac0ae903fa8d0cc2ff9f79d
Cc: mtosatti@redhat.com
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

KVM: x86: limit PIT timer frequency

commit 9ed96e87c5748de4c2807ef17e81287c7304186c upstream.

Limit PIT timer frequency similarly to the limit applied by
LAPIC timer.

Reviewed-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

x86/efi: Fix off-by-one bug in EFI Boot Services reservation

commit a7f84f03f660d93574ac88835d056c0d6468aebe upstream.

Current code check boot service region with kernel text region by:
start+size >= __pa_symbol(_text)
The end of the above region should be start + size - 1 instead.

I see this problem in ovmf + Fedora 19 grub boot:
text start: 1000000 md start: 800000 md size: 800000

Signed-off-by: Dave Young <dyoung@redhat.com>
Acked-by: Borislav Petkov <bp@suse.de>
Acked-by: Toshi Kani <toshi.kani@hp.com>
Tested-by: Toshi Kani <toshi.kani@hp.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

x86, x32: Correct invalid use of user timespec in the kernel

commit 2def2ef2ae5f3990aabdbe8a755911902707d268 upstream.

The x32 case for the recvmsg() timout handling is broken:

  asmlinkage long compat_sys_recvmmsg(int fd, struct compat_mmsghdr __user *mmsg,
                                      unsigned int vlen, unsigned int flags,
                                      struct compat_timespec __user *timeout)
  {
          int datagrams;
          struct timespec ktspec;

          if (flags & MSG_CMSG_COMPAT)
                  return -EINVAL;

          if (COMPAT_USE_64BIT_TIME)
                  return __sys_recvmmsg(fd, (struct mmsghdr __user *)mmsg, vlen,
                                        flags | MSG_CMSG_COMPAT,
                                        (struct timespec *) timeout);
          ...

The timeout pointer parameter is provided by userland (hence the __user
annotation) but for x32 syscalls it's simply cast to a kernel pointer
and is passed to __sys_recvmmsg which will eventually directly
dereference it for both reading and writing.  Other callers to
__sys_recvmmsg properly copy from userland to the kernel first.

The bug was introduced by commit ee4fa23c4bfc ("compat: Use
COMPAT_USE_64BIT_TIME in net/compat.c") and should affect all kernels
since 3.4 (and perhaps vendor kernels if they backported x32 support
along with this code).

Note that CONFIG_X86_X32_ABI gets enabled at build time and only if
CONFIG_X86_X32 is enabled and ld can build x32 executables.

Other uses of COMPAT_USE_64BIT_TIME seem fine.

This addresses CVE-2014-0038.

Signed-off-by: PaX Team <pageexec@freemail.hu>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mm/mempolicy.c: fix mempolicy printing in numa_maps

commit 8790c71a18e5d2d93532ae250bcf5eddbba729cd upstream.

As a result of commit 5606e3877ad8 ("mm: numa: Migrate on reference
policy"), /proc/<pid>/numa_maps prints the mempolicy for any <pid> as
"prefer:N" for the local node, N, of the process reading the file.

This should only be printed when the mempolicy of <pid> is
MPOL_PREFERRED for node N.

If the process is actually only using the default mempolicy for local
node allocation, make sure "default" is printed as expected.

Signed-off-by: David Rientjes <rientjes@google.com>
Reported-by: Robert Lippert <rlippert@google.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Acked-by: Mel Gorman <mgorman@suse.de>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: <stable@vger.kernel.org> [3.7+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

e1000e: fix compiler warnings

commit 9e6c3b63399dd424d33a34e08b77f2cab0b84cdc upstream.

This patch is to fix a compiler warning of __bad_udelay due to a value
of >999 being passed as a parameter to udelay() in the function
e1000e_phy_has_link_generic().  This affects the gcc compiler when
it is given a flag of -O3 and the icc compiler.

This patch is also making the change from mdelay() to msleep() in the
same function, since it was determined though code inspection that this
function is never called in atomic context.

Signed-off-by: David Ertman <davidx.m.ertman@intel.com>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

e752x_edac: Fix pci_dev usage count

commit 90ed4988b8c030d65b41b7d13140e9376dc6ec5a upstream.

In case the device 0, function 1 is not found using pci_get_device(),
pci_scan_single_device() will be used but, differently than
pci_get_device(), it allocates a pci_dev but doesn't does bump the usage
count on the pci_dev and after few module removals and loads the pci_dev
will be freed.

Signed-off-by: Aristeu Rozanski <aris@redhat.com>
Reviewed-by: mark gross <mark.gross@intel.com>
Link: http://lkml.kernel.org/r/20131205153755.GL4545@redhat.com
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mm: hugetlbfs: fix hugetlbfs optimization

commit 27c73ae759774e63313c1fbfeb17ba076cea64c5 upstream.

Commit 7cb2ef56e6a8 ("mm: fix aio performance regression for database
caused by THP") can cause dereference of a dangling pointer if
split_huge_page runs during PageHuge() if there are updates to the
tail_page->private field.

Also it is repeating compound_head twice for hugetlbfs and it is running
compound_head+compound_trans_head for THP when a single one is needed in
both cases.

The new code within the PageSlab() check doesn't need to verify that the
THP page size is never bigger than the smallest hugetlbfs page size, to
avoid memory corruption.

A longstanding theoretical race condition was found while fixing the
above (see the change right after the skip_unlock label, that is
relevant for the compound_lock path too).

By re-establishing the _mapcount tail refcounting for all compound
pages, this also fixes the below problem:

  echo 0 >/sys/kernel/mm/hugepages/hugepages-2048kB/nr_hugepages

  BUG: Bad page state in process bash  pfn:59a01
  page:ffffea000139b038 count:0 mapcount:10 mapping:          (null) index:0x0
  page flags: 0x1c00000000008000(tail)
  Modules linked in:
  CPU: 6 PID: 2018 Comm: bash Not tainted 3.12.0+ #25
  Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
  Call Trace:
    dump_stack+0x55/0x76
    bad_page+0xd5/0x130
    free_pages_prepare+0x213/0x280
    __free_pages+0x36/0x80
    update_and_free_page+0xc1/0xd0
    free_pool_huge_page+0xc2/0xe0
    set_max_huge_pages.part.58+0x14c/0x220
    nr_hugepages_store_common.isra.60+0xd0/0xf0
    nr_hugepages_store+0x13/0x20
    kobj_attr_store+0xf/0x20
    sysfs_write_file+0x189/0x1e0
    vfs_write+0xc5/0x1f0
    SyS_write+0x55/0xb0
    system_call_fastpath+0x16/0x1b

Signed-off-by: Khalid Aziz <khalid.aziz@oracle.com>
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Tested-by: Khalid Aziz <khalid.aziz@oracle.com>
Cc: Pravin Shelar <pshelar@nicira.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Johannes Weiner <jweiner@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Rik van Riel <riel@redhat.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Minchan Kim <minchan@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Guillaume Morin <guillaume@morinfr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/nouveau/bios: fix offset calculation for BMPv1 bioses

commit 5d2f4767c4eacab351b8450b0de4d3261fe1a957 upstream.

The only BIOS on record that needs the 14 offset has a bios major
version 2 but BMP version 1.01. Another bunch of BIOSes that need the 18
offset have BMP version 2.01 or 5.01 or higher. So instead of looking at the
bios major version, look at the BMP version. BIOSes with BMP version 0
do not contain a detectable script, so always return 0 for them.

See https://bugs.freedesktop.org/show_bug.cgi?id=68835

Reported-by: Mauro Molinari <mauromol@tiscali.it>
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

md/raid5: fix long-standing problem with bitmap handling on write failure.

commit 9f97e4b128d2ea90a5f5063ea0ee3b0911f4c669 upstream.

Before a write starts we set a bit in the write-intent bitmap.
When the write completes we clear that bit if the write was successful
to all devices.  However if the write wasn't fully successful we
should not clear the bit.  If the faulty drive is subsequently
re-added, the fact that the bit is still set ensure that we will
re-write the data that is missing.

This logic is mediated by the STRIPE_DEGRADED flag - we only clear the
bitmap bit when this flag is not set.
Currently we correctly set the flag if a write starts when some
devices are failed or missing.  But we do *not* set the flag if some
device failed during the write attempt.
This is wrong and can result in clearing the bit inappropriately.

So: set the flag when a write fails.

This bug has been present since bitmaps were introduces, so the fix is
suitable for any -stable kernel.

Reported-by: Ethan Wilson <ethan.wilson@shiftmail.org>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

kvm: x86: fix apic_base enable check

commit 0dce7cd67fd9055c4a2ff278f8af1431e646d346 upstream.

Commit e66d2ae7c67bd moved the assignment
vcpu->arch.apic_base = value above a condition with
(vcpu->arch.apic_base ^ value), causing that check
to always fail. Use old_value, vcpu->arch.apic_base's
old value, in the condition instead.

Signed-off-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Linux 3.12.9

ARM: 7938/1: OMAP4/highbank: Flush L2 cache before disabling

commit b25f3e1c358434bf850220e04f28eebfc45eb634 upstream.

Kexec disables outer cache before jumping to reboot code, but it doesn't
flush it explicitly. Flush is done implicitly inside of l2x0_disable().
But some SoC's override default .disable handler and don't flush cache.
This may lead to a corrupted memory during Kexec reboot on these
platforms.

This patch adds cache flush inside of OMAP4 and Highbank outer_cache.disable()
handlers to make it consistent with default l2x0_disable().

Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Taras Kondratiuk <taras.kondratiuk@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Wang Nan <wangnan0@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/i915: Don't grab crtc mutexes in intel_modeset_gem_init()

commit 7ad228b11ec26a820291c9f5a1168d6176580dc1 upstream.

When the pipe A force quirk is applied the code will attempt to grab
a crtc mutex during intel_modeset_setup_hw_state(). If we're already
holding all crtc mutexes this will obviously deadlock every time.

So instead of using drm_modeset_lock_all() just grab the
mode_config.mutex. This is enough to avoid the unlocked mutex warnings
from certain lower level functions.

The regression was introduced in:

 commit 027476642811f8559cbe00ef6cc54db230e48a20
 Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
 Date:   Mon Dec 2 11:08:06 2013 +0200

    drm/i915: Take modeset locks around intel_modeset_setup_hw_state()

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Add cc: stable since the offending commit has that, too.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARM: 7934/1: DT/kernel: fix arch_match_cpu_phys_id to avoid erroneous match

commit e44ef891e9e68b6ce7d3fd3bac73b7d5433050ae upstream.

The MPIDR contains specific bitfields(MPIDR.Aff{2..0}) which uniquely
identify a CPU, in addition to some non-identifying information and
reserved bits. The ARM cpu binding defines the 'reg' property to only
contain the affinity bits, and any cpu nodes with other bits set in
their 'reg' entry are skipped.

As such it is not necessary to mask the phys_id with MPIDR_HWID_BITMASK,
and doing so could lead to matching erroneous CPU nodes in the device
tree. This patch removes the masking of the physical identifier.

Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: amba-pl011: use port lock to guard control register access

commit fe43390702a1b5741fdf217063b05c7612b38303 upstream.

When the pl011 is being used for a console, pl011_console_write forces
the control register (CR) to enable the UART for transmission and then
restores this to the original value afterwards. It does this while
holding the port lock.

Unfortunately, when the uart is started or shutdown - say in response to
userland using the serial device for a terminal - then this updates the
control register without any locking.

This means we can have

  pl011_console_write   Save CR
  pl011_startup         Initialise CR, e.g. enable receive
  pl011_console_write   Restore old CR with receive not enabled

this result is a serial port which doesn't respond to any input.

A similar race in reverse could happen when the device is shutdown.

We can fix these problems by taking the port lock when updating CR.

Signed-off-by: Jon Medhurst <tixy@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mm: Make {,set}page_address() static inline if WANT_PAGE_VIRTUAL

commit f92f455f67fef27929e6043499414605b0c94872 upstream.

{,set}page_address() are macros if WANT_PAGE_VIRTUAL.  If
!WANT_PAGE_VIRTUAL, they're plain C functions.

If someone calls them with a void *, this pointer is auto-converted to
struct page * if !WANT_PAGE_VIRTUAL, but causes a build failure on
architectures using WANT_PAGE_VIRTUAL (arc, m68k and sparc64):

  drivers/md/bcache/bset.c: In function `__btree_sort':
  drivers/md/bcache/bset.c:1190: warning: dereferencing `void *' pointer
  drivers/md/bcache/bset.c:1190: error: request for member `virtual' in something not a structure or union

Convert them to static inline functions to fix this.  There are already
plenty of users of struct page members inside <linux/mm.h>, so there's
no reason to keep them as macros.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

md/raid5: Fix possible confusion when multiple write errors occur.

commit 1cc03eb93245e63b0b7a7832165efdc52e25b4e6 upstream.

commit 5d8c71f9e5fbdd95650be00294d238e27a363b5c
    md: raid5 crash during degradation

Fixed a crash in an overly simplistic way which could leave
R5_WriteError or R5_MadeGood set in the stripe cache for devices
for which it is no longer relevant.
When those devices are removed and spares added the flags are still
set and can cause incorrect behaviour.

commit 14a75d3e07c784c004b4b44b34af996b8e4ac453
    md/raid5: preferentially read from replacement device if possible.

Fixed the same bug if a more effective way, so we can now revert
the original commit.

Reported-and-tested-by: Alexander Lyakas <alex.bolshoy@gmail.com>
Fixes: 5d8c71f9e5fbdd95650be00294d238e27a363b5c
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

md/raid10: fix two bugs in handling of known-bad-blocks.

commit b50c259e25d9260b9108dc0c2964c26e5ecbe1c1 upstream.

If we discover a bad block when reading we split the request and
potentially read some of it from a different device.

The code path of this has two bugs in RAID10.
1/ we get a spin_lock with _irq, but unlock without _irq!!
2/ The calculation of 'sectors_handled' is wrong, as can be clearly
   seen by comparison with raid1.c

This leads to at least 2 warnings and a probable crash is a RAID10
ever had known bad blocks.

Fixes: 856e08e23762dfb92ffc68fd0a8d228f9e152160
Reported-by: Damian Nowak <spam@nowaker.net>
URL: https://bugzilla.kernel.org/show_bug.cgi?id=68181
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

md/raid10: fix bug when raid10 recovery fails to recover a block.

commit e8b849158508565e0cd6bc80061124afc5879160 upstream.

commit e875ecea266a543e643b19e44cf472f1412708f9
    md/raid10 record bad blocks as needed during recovery.

added code to the "cannot recover this block" path to record a bad
block rather than fail the whole recovery.
Unfortunately this new case was placed *after* r10bio was freed rather
than *before*, yet it still uses r10bio.
This is will crash with a null dereference.

So move the freeing of r10bio down where it is safe.

Fixes: e875ecea266a543e643b19e44cf472f1412708f9
Reported-by: Damian Nowak <spam@nowaker.net>
URL: https://bugzilla.kernel.org/show_bug.cgi?id=68181
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

md: fix problem when adding device to read-only array with bitmap.

commit 8313b8e57f55b15e5b7f7fc5d1630bbf686a9a97 upstream.

If an array is started degraded, and then the missing device
is found it can be re-added and a minimal bitmap-based recovery
will bring it fully up-to-date.

If the array is read-only a recovery would not be allowed.
But also if the array is read-only and the missing device was
present very recently, then there could be no need for any
recovery at all, so we simply include the device in the read-only
array without any recovery.

However... if the missing device was removed a little longer ago
it could be missing some updates, but if a bitmap is present it will
be conditionally accepted pending a bitmap-based update.  We don't
currently detect this case properly and will include that old
device into the read-only array with no recovery even though it really
needs a recovery.

This patch keeps track of whether a bitmap-based-recovery is really
needed or not in the new Bitmap_sync rdev flag.  If that is set,
then the device will not be added to a read-only array.

Cc: Andrei Warkentin <andreiw@vmware.com>
Fixes: d70ed2e4fafdbef0800e73942482bb075c21578b
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/i915: fix DDI PLLs HW state readout code

commit 0882dae983707455e97479e5e904e37673517ebc upstream.

Properly zero the refcounts and crtc->ddi_pll_set so the previous HW
state doesn't affect the result of reading the current HW state.

This fixes WARNs about WRPLL refcount if we have an HDMI monitor on
HSW and then suspend/resume.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=64379
Tested-by: Qingshuai Tian <qingshuai.tian@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

nilfs2: fix segctor bug that causes file system corruption

commit 70f2fe3a26248724d8a5019681a869abdaf3e89a upstream.

There is a bug in the function nilfs_segctor_collect, which results in
active data being written to a segment, that is marked as clean.  It is
possible, that this segment is selected for a later segment
construction, whereby the old data is overwritten.

The problem shows itself with the following kernel log message:

  nilfs_sufile_do_cancel_free: segment 6533 must be clean

Usually a few hours later the file system gets corrupted:

  NILFS: bad btree node (blocknr=8748107): level = 0, flags = 0x0, nchildren = 0
  NILFS error (device sdc1): nilfs_bmap_last_key: broken bmap (inode number=114660)

The issue can be reproduced with a file system that is nearly full and
with the cleaner running, while some IO intensive task is running.
Although it is quite hard to reproduce.

This is what happens:

 1. The cleaner starts the segment construction
 2. nilfs_segctor_collect is called
 3. sc_stage is on NILFS_ST_SUFILE and segments are freed
 4. sc_stage is on NILFS_ST_DAT current segment is full
 5. nilfs_segctor_extend_segments is called, which
    allocates a new segment
 6. The new segment is one of the segments freed in step 3
 7. nilfs_sufile_cancel_freev is called and produces an error message
 8. Loop around and the collection starts again
 9. sc_stage is on NILFS_ST_SUFILE and segments are freed
    including the newly allocated segment, which will contain active
    data and can be allocated at a later time
10. A few hours later another segment construction allocates the
    segment and causes file system corruption

This can be prevented by simply reordering the statements.  If
nilfs_sufile_cancel_freev is called before nilfs_segctor_extend_segments
the freed segments are marked as dirty and cannot be allocated any more.

Signed-off-by: Andreas Rohner <andreas.rohner@gmx.net>
Reviewed-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Tested-by: Andreas Rohner <andreas.rohner@gmx.net>
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mm: fix crash when using XFS on loopback

commit 03e5ac2fc3bf6f4140db0371e8bb4243b24e3e02 upstream.

Commit 8456a648cf44 ("slab: use struct page for slab management") causes
a crash in the LVM2 testsuite on PA-RISC (the crashing test is
fsadm.sh).  The testsuite doesn't crash on 3.12, crashes on 3.13-rc1 and
later.

 Bad Address (null pointer deref?): Code=15 regs=000000413edd89a0 (Addr=000006202224647d)
 CPU: 3 PID: 24008 Comm: loop0 Not tainted 3.13.0-rc6 #5
 task: 00000001bf3c0048 ti: 000000413edd8000 task.ti: 000000413edd8000

      YZrvWESTHLNXBCVMcbcbcbcbOGFRQPDI
 PSW: 00001000000001101111100100001110 Not tainted
 r00-03  000000ff0806f90e 00000000405c8de0 000000004013e6c0 000000413edd83f0
 r04-07  00000000405a95e0 0000000000000200 00000001414735f0 00000001bf349e40
 r08-11  0000000010fe3d10 0000000000000001 00000040829c7778 000000413efd9000
 r12-15  0000000000000000 000000004060d800 0000000010fe3000 0000000010fe3000
 r16-19  000000413edd82a0 00000041078ddbc0 0000000000000010 0000000000000001
 r20-23  0008f3d0d83a8000 0000000000000000 00000040829c7778 0000000000000080
 r24-27  00000001bf349e40 00000001bf349e40 202d66202224640d 00000000405a95e0
 r28-31  202d662022246465 000000413edd88f0 000000413edd89a0 0000000000000001
 sr00-03  000000000532c000 0000000000000000 0000000000000000 000000000532c000
 sr04-07  0000000000000000 0000000000000000 0000000000000000 0000000000000000

 IASQ: 0000000000000000 0000000000000000 IAOQ: 00000000401fe42c 00000000401fe430
  IIR: 539c0030    ISR: 00000000202d6000  IOR: 000006202224647d
  CPU:        3   CR30: 000000413edd8000 CR31: 0000000000000000
  ORIG_R28: 00000000405a95e0
  IAOQ[0]: vma_interval_tree_iter_first+0x14/0x48
  IAOQ[1]: vma_interval_tree_iter_first+0x18/0x48
  RP(r2): flush_dcache_page+0x128/0x388
 Backtrace:
   flush_dcache_page+0x128/0x388
   lo_splice_actor+0x90/0x148 [loop]
   splice_from_pipe_feed+0xc0/0x1d0
   __splice_from_pipe+0xac/0xc0
   lo_direct_splice_actor+0x1c/0x70 [loop]
   splice_direct_to_actor+0xec/0x228
   lo_receive+0xe4/0x298 [loop]
   loop_thread+0x478/0x640 [loop]
   kthread+0x134/0x168
   end_fault_vector+0x20/0x28
   xfs_setsize_buftarg+0x0/0x90 [xfs]

 Kernel panic - not syncing: Bad Address (null pointer deref?)

Commit 8456a648cf44 changes the page structure so that the slab
subsystem reuses the page->mapping field.

The crash happens in the following way:
 * XFS allocates some memory from slab and issues a bio to read data
   into it.
 * the bio is sent to the loopback device.
 * lo_receive creates an actor and calls splice_direct_to_actor.
 * lo_splice_actor copies data to the target page.
 * lo_splice_actor calls flush_dcache_page because the page may be
   mapped by userspace.  In that case we need to flush the kernel cache.
 * flush_dcache_page asks for the list of userspace mappings, however
   that page->mapping field is reused by the slab subsystem for a
   different purpose.  This causes the crash.

Note that other architectures without coherent caches (sparc, arm, mips)
also call page_mapping from flush_dcache_page, so they may crash in the
same way.

This patch fixes this bug by testing if the page is a slab page in
page_mapping and returning NULL if it is.

The patch also fixes VM_BUG_ON(PageSlab(page)) that could happen in
earlier kernels in the same scenario on architectures without cache
coherence when CONFIG_DEBUG_VM is enabled - so it should be backported
to stable kernels.

In the old kernels, the function page_mapping is placed in
include/linux/mm.h, so you should modify the patch accordingly when
backporting it.

Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: John David Anglin <dave.anglin@bell.net>]
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Christoph Lameter <cl@linux.com>
Acked-by: Pekka Enberg <penberg@kernel.org>
Reviewed-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Helge Deller <deller@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

crash_dump: fix compilation error (on MIPS at least)

commit 5a610fcc7390ee60308deaf09426ada87a1eeec2 upstream.

  In file included from kernel/crash_dump.c:2:0:
  include/linux/crash_dump.h:22:27: error: unknown type name `pgprot_t'

when CONFIG_CRASH_DUMP=y

The error was traced back to commit 9cb218131de1 ("vmcore: introduce
remap_oldmem_pfn_range()")

include <asm/pgtable.h> to get the missing definition

Signed-off-by: Qais Yousef <qais.yousef@imgtec.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Cc: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ftrace/x86: Load ftrace_ops in parameter not the variable holding it

commit 1739f09e33d8f66bf48ddbc3eca615574da6c4f6 upstream.

Function tracing callbacks expect to have the ftrace_ops that registered it
passed to them, not the address of the variable that holds the ftrace_ops
that registered it.

Use a mov instead of a lea to store the ftrace_ops into the parameter
of the function tracing callback.

Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Reviewed-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Link: http://lkml.kernel.org/r/20131113152004.459787f9@gandalf.local.home
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

thp: fix copy_page_rep GPF by testing is_huge_zero_pmd once only

commit eecc1e426d681351a6026a7d3e7d225f38955b6c upstream.

We see General Protection Fault on RSI in copy_page_rep: that RSI is
what you get from a NULL struct page pointer.

  RIP: 0010:[<ffffffff81154955>]  [<ffffffff81154955>] copy_page_rep+0x5/0x10
  RSP: 0000:ffff880136e15c00  EFLAGS: 00010286
  RAX: ffff880000000000 RBX: ffff880136e14000 RCX: 0000000000000200
  RDX: 6db6db6db6db6db7 RSI: db73880000000000 RDI: ffff880dd0c00000
  RBP: ffff880136e15c18 R08: 0000000000000200 R09: 000000000005987c
  R10: 000000000005987c R11: 0000000000000200 R12: 0000000000000001
  R13: ffffea00305aa000 R14: 0000000000000000 R15: 0000000000000000
  FS:  00007f195752f700(0000) GS:ffff880c7fc20000(0000) knlGS:0000000000000000
  CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
  CR2: 0000000093010000 CR3: 00000001458e1000 CR4: 00000000000027e0
  Call Trace:
    copy_user_huge_page+0x93/0xab
    do_huge_pmd_wp_page+0x710/0x815
    handle_mm_fault+0x15d8/0x1d70
    __do_page_fault+0x14d/0x840
    do_page_fault+0x2f/0x90
    page_fault+0x22/0x30

do_huge_pmd_wp_page() tests is_huge_zero_pmd(orig_pmd) four times: but
since shrink_huge_zero_page() can free the huge_zero_page, and we have
no hold of our own on it here (except where the fourth test holds
page_table_lock and has checked pmd_same), it's possible for it to
answer yes the first time, but no to the second or third test.  Change
all those last three to tests for NULL page.

(Note: this is not the same issue as trinity's DEBUG_PAGEALLOC BUG
in copy_page_rep with RSI: ffff88009c422000, reported by Sasha Levin
in https://lkml.org/lkml/2013/3/29/103.  I believe that one is due
to the source page being split, and a tail page freed, while copy
is in progress; and not a problem without DEBUG_PAGEALLOC, since
the pmd_same check will prevent a miscopy from being made visible.)

Fixes: 97ae17497e99 ("thp: implement refcounting for huge zero page")
Signed-off-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

SELinux: Fix possible NULL pointer dereference in selinux_inode_permission()

commit 3dc91d4338d698ce77832985f9cb183d8eeaf6be upstream.

While running stress tests on adding and deleting ftrace instances I hit
this bug:

  BUG: unable to handle kernel NULL pointer dereference at 0000000000000020
  IP: selinux_inode_permission+0x85/0x160
  PGD 63681067 PUD 7ddbe067 PMD 0
  Oops: 0000 [#1] PREEMPT
  CPU: 0 PID: 5634 Comm: ftrace-test-mki Not tainted 3.13.0-rc4-test-00033-gd2a6dde-dirty #20
  Hardware name:                  /DG965MQ, BIOS MQ96510J.86A.0372.2006.0605.1717 06/05/2006
  task: ffff880078375800 ti: ffff88007ddb0000 task.ti: ffff88007ddb0000
  RIP: 0010:[<ffffffff812d8bc5>]  [<ffffffff812d8bc5>] selinux_inode_permission+0x85/0x160
  RSP: 0018:ffff88007ddb1c48  EFLAGS: 00010246
  RAX: 0000000000000000 RBX: 0000000000800000 RCX: ffff88006dd43840
  RDX: 0000000000000001 RSI: 0000000000000081 RDI: ffff88006ee46000
  RBP: ffff88007ddb1c88 R08: 0000000000000000 R09: ffff88007ddb1c54
  R10: 6e6576652f6f6f66 R11: 0000000000000003 R12: 0000000000000000
  R13: 0000000000000081 R14: ffff88006ee46000 R15: 0000000000000000
  FS:  00007f217b5b6700(0000) GS:ffffffff81e21000(0000) knlGS:0000000000000000
  CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033^M
  CR2: 0000000000000020 CR3: 000000006a0fe000 CR4: 00000000000007f0
  Call Trace:
    security_inode_permission+0x1c/0x30
    __inode_permission+0x41/0xa0
    inode_permission+0x18/0x50
    link_path_walk+0x66/0x920
    path_openat+0xa6/0x6c0
    do_filp_open+0x43/0xa0
    do_sys_open+0x146/0x240
    SyS_open+0x1e/0x20
    system_call_fastpath+0x16/0x1b
  Code: 84 a1 00 00 00 81 e3 00 20 00 00 89 d8 83 c8 02 40 f6 c6 04 0f 45 d8 40 f6 c6 08 74 71 80 cf 02 49 8b 46 38 4c 8d 4d cc 45 31 c0 <0f> b7 50 20 8b 70 1c 48 8b 41 70 89 d9 8b 78 04 e8 36 cf ff ff
  RIP  selinux_inode_permission+0x85/0x160
  CR2: 0000000000000020

Investigating, I found that the inode->i_security was NULL, and the
dereference of it caused the oops.

in selinux_inode_permission():

isec = inode->i_security;

rc = avc_has_perm_noaudit(sid, isec->sid, isec->sclass, perms, 0, &avd);

Note, the crash came from stressing the deletion and reading of debugfs
files.  I was not able to recreate this via normal files.  But I'm not
sure they are safe.  It may just be that the race window is much harder
to hit.

What seems to have happened (and what I have traced), is the file is
being opened at the same time the file or directory is being deleted.
As the dentry and inode locks are not held during the path walk, nor is
the inodes ref counts being incremented, there is nothing saving these
structures from being discarded except for an rcu_read_lock().

The rcu_read_lock() protects against freeing of the inode, but it does
not protect freeing of the inode_security_struct.  Now if the freeing of
the i_security happens with a call_rcu(), and the i_security field of
the inode is not changed (it gets freed as the inode gets freed) then
there will be no issue here.  (Linus Torvalds suggested not setting the
field to NULL such that we do not need to check if it is NULL in the
permission check).

Note, this is a hack, but it fixes the problem at hand.  A real fix is
to restructure the destroy_inode() to call all the destructor handlers
from the RCU callback.  But that is a major job to do, and requires a
lot of work.  For now, we just band-aid this bug with this fix (it
works), and work on a more maintainable solution in the future.

Link: http://lkml.kernel.org/r/20140109101932.0508dec7@gandalf.local.home
Link: http://lkml.kernel.org/r/20140109182756.17abaaa8@gandalf.local.home
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

writeback: Fix data corruption on NFS

commit f9b0e058cbd04ada76b13afffa7e1df830543c24 upstream.

Commit 4f8ad655dbc8 "writeback: Refactor writeback_single_inode()" added
a condition to skip clean inode. However this is wrong in WB_SYNC_ALL
mode because there we also want to wait for outstanding writeback on
possibly clean inode. This was causing occasional data corruption issues
on NFS because it uses sync_inode() to make sure all outstanding writes
are flushed to the server before truncating the inode and with
sync_inode() returning prematurely file was sometimes extended back
by an outstanding write after it was truncated.

So modify the test to also check for pages under writeback in
WB_SYNC_ALL mode.

Fixes: 4f8ad655dbc82cf05d2edc11e66b78a42d38bf93
Reported-and-tested-by: Dan Duval <dan.duval@oracle.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

hwmon: (coretemp) Fix truncated name of alarm attributes

commit 3f9aec7610b39521c7c69d754de7265f6994c194 upstream.

When the core number exceeds 9, the size of the buffer storing the
alarm attribute name is insufficient and the attribute name is
truncated. This causes libsensors to skip these attributes as the
truncated name is not recognized.

Reported-by: Andreas Hollmann <hollmann@in.tum.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

i2c: Re-instate body of i2c_parent_is_i2c_adapter()

commit 2fac2b891f287691c27ee8d2eeecf39571b27fea upstream.

The body of i2c_parent_is_i2c_adapter() is currently guarded by
I2C_MUX. It should be CONFIG_I2C_MUX instead.

Among potentially other problems, this resulted in i2c_lock_adapter()
only locking I2C mux child adapters, and not the parent adapter. In
turn, this could allow inter-mingling of mux child selection and I2C
transactions, which could result in I2C transactions being directed to
the wrong I2C bus, and possibly even switching between busses in the
middle of a transaction.

One concrete issue caused by this bug was corrupted HDMI EDID reads
during boot on the NVIDIA Tegra Seaboard system, although this only
became apparent in recent linux-next, when the boot timing was changed
just enough to trigger the race condition.

Fixes: 3923172b3d70 ("i2c: reduce parent checking to a NOOP in non-I2C_MUX case")
Cc: Phil Carmody <phil.carmody@partner.samsung.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

fork: Allow CLONE_PARENT after setns(CLONE_NEWPID)

commit 1f7f4dde5c945f41a7abc2285be43d918029ecc5 upstream.

Serge Hallyn <serge.hallyn@ubuntu.com> writes:
> Hi Oleg,
>
> commit 40a0d32d1eaffe6aac7324ca92604b6b3977eb0e :
> "fork: unify and tighten up CLONE_NEWUSER/CLONE_NEWPID checks"
> breaks lxc-attach in 3.12.  That code forks a child which does
> setns() and then does a clone(CLONE_PARENT).  That way the
> grandchild can be in the right namespaces (which the child was
> not) and be a child of the original task, which is the monitor.
>
> lxc-attach in 3.11 was working fine with no side effects that I
> could see.  Is there a real danger in allowing CLONE_PARENT
> when current->nsproxy->pidns_for_children is not our pidns,
> or was this done out of an "over-abundance of caution"?  Can we
> safely revert that new extra check?

The two fundamental things I know we can not allow are:
- A shared signal queue aka CLONE_THREAD.  Because we compute the pid
  and uid of the signal when we place it in the queue.

- Changing the pid and by extention pid_namespace of an existing
  process.

From a parents perspective there is nothing special about the pid
namespace, to deny CLONE_PARENT, because the parent simply won't know or
care.

From the childs perspective all that is special really are shared signal
queues.

User mode threading with CLONE_PARENT|CLONE_VM|CLONE_SIGHAND and tasks
in different pid namespaces is almost certainly going to break because
it is complicated.  But shared signal handlers can look at per thread
information to know which pid namespace a process is in, so I don't know
of any reason not to support CLONE_PARENT|CLONE_VM|CLONE_SIGHAND threads
at the kernel level.  It would be absolutely stupid to implement but
that is a different thing.

So hmm.

Because it can do no harm, and because it is a regression let's remove
the CLONE_PARENT check and send it stable.

Acked-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Andy Lutomirski <luto@amacapital.net>
Acked-by: Serge E. Hallyn <serge.hallyn@ubuntu.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

vfs: Fix a regression in mounting proc

commit 41301ae78a99ead04ea42672a1ab72c6f44cc81d upstream.

Gao feng <gaofeng@cn.fujitsu.com> reported that commit
e51db73532955dc5eaba4235e62b74b460709d5b
userns: Better restrictions on when proc and sysfs can be mounted
caused a regression on mounting a new instance of proc in a mount
namespace created with user namespace privileges, when binfmt_misc
is mounted on /proc/sys/fs/binfmt_misc.

This is an unintended regression caused by the absolutely bogus empty
directory check in fs_fully_visible.  The check fs_fully_visible replaced
didn't even bother to attempt to verify proc was fully visible and
hiding proc files with any kind of mount is rare.  So for now fix
the userspace regression by allowing directory with nlink == 1
as /proc/sys/fs/binfmt_misc has.

I will have a better patch but it is not stable material, or
last minute kernel material.  So it will have to wait.

Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Acked-by: Gao feng <gaofeng@cn.fujitsu.com>
Tested-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

vfs: In d_path don't call d_dname on a mount point

commit f48cfddc6729ef133933062320039808bafa6f45 upstream.

Aditya Kali (adityakali@google.com) wrote:
> Commit bf056bfa80596a5d14b26b17276a56a0dcb080e5:
> "proc: Fix the namespace inode permission checks." converted
> the namespace files into symlinks. The same commit changed
> the way namespace bind mounts appear in /proc/mounts:
>   $ mount --bind /proc/self/ns/ipc /mnt/ipc
> Originally:
>   $ cat /proc/mounts | grep ipc
>   proc /mnt/ipc proc rw,nosuid,nodev,noexec 0 0
>
> After commit bf056bfa80596a5d14b26b17276a56a0dcb080e5:
>   $ cat /proc/mounts | grep ipc
>   proc ipc:[4026531839] proc rw,nosuid,nodev,noexec 0 0
>
> This breaks userspace which expects the 2nd field in
> /proc/mounts to be a valid path.

The symlink /proc/<pid>/ns/{ipc,mnt,net,pid,user,uts} point to
dentries allocated with d_alloc_pseudo that we can mount, and
that have interesting names printed out with d_dname.

When these files are bind mounted /proc/mounts is not currently
displaying the mount point correctly because d_dname is called instead
of just displaying the path where the file is mounted.

Solve this by adding an explicit check to distinguish mounted pseudo
inodes and unmounted pseudo inodes.  Unmounted pseudo inodes always
use mount of their filesstem as the mnt_root  in their path making
these two cases easy to distinguish.

Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Reported-by: Aditya Kali <adityakali@google.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: comedi: adl_pci9111: fix incorrect irq passed to request_irq()

commit 48108fe3daa0d142f9b97178fdb23704ea3a407b upstream.

The dev->irq passed to request_irq() will always be 0 when the auto_attach
function is called. The pcidev->irq should be used instead to get the correct
irq number.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: comedi: addi_apci_1032: fix subdevice type/flags bug

commit 90daf69a7a3f1d1a41018c799968a0bb896d65e0 upstream.

The SDF_CMD_READ should be one of the s->subdev_flags not part of
the s->type.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

GFS2: Increase i_writecount during gfs2_setattr_chown

commit 62e96cf81988101fe9e086b2877307b6adda5197 upstream.

This patch calls get_write_access in function gfs2_setattr_chown,
which merely increases inode->i_writecount for the duration of the
function. That will ensure that any file closes won't delete the
inode's multi-block reservation while the function is running.
It also ensures that a multi-block reservation exists when needed
for quota change operations during the chown.

Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

perf/x86/amd/ibs: Fix waking up from S3 for AMD family 10h

commit bee09ed91cacdbffdbcd3b05de8409c77ec9fcd6 upstream.

On AMD family 10h we see following error messages while waking up from
S3 for all non-boot CPUs leading to a failed IBS initialization:

 Enabling non-boot CPUs ...
 smpboot: Booting Node 0 Processor 1 APIC 0x1
 [Firmware Bug]: cpu 1, try to use APIC500 (LVT offset 0) for vector 0x400, but the register is already in use for vector 0xf9 on another cpu
 perf: IBS APIC setup failed on cpu #1
 process: Switch to broadcast mode on CPU1
 CPU1 is up
 ...
 ACPI: Waking up from system sleep state S3

Reason for this is that during suspend the LVT offset for the IBS
vector gets lost and needs to be reinialized while resuming.

The offset is read from the IBSCTL msr. On family 10h the offset needs
to be 1 as offset 0 is used for the MCE threshold interrupt, but
firmware assings it for IBS to 0 too. The kernel needs to reprogram
the vector. The msr is a readonly node msr, but a new value can be
written via pci config space access. The reinitialization is
implemented for family 10h in setup_ibs_ctl() which is forced during
IBS setup.

This patch fixes IBS setup after waking up from S3 by adding
resume/supend hooks for the boot cpu which does the offset
reinitialization.

Marking it as stable to let distros pick up this fix.

Signed-off-by: Robert Richter <rric@kernel.org>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/1389797849-5565-1-git-send-email-rric.net@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Revert "ACPI: Add BayTrail SoC GPIO and LPSS ACPI IDs"

commit 2b844ba79f4a114bd228ad6fee040ffd99a0963d upstream.

This reverts commit f6308b36c411 (ACPI: Add BayTrail SoC GPIO and LPSS
ACPI IDs), because it causes the Alan Cox' ASUS T100TA to "crash and
burn" during boot if the Baytrail pinctrl driver is compiled in.

Fixes: f6308b36c411 (ACPI: Add BayTrail SoC GPIO and LPSS ACPI IDs)
Reported-by: One Thousand Gnomes <gnomes@lxorguk.ukuu.org.uk>
Requested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Linux 3.12.8

sched: Guarantee new group-entities always have weight

commit 0ac9b1c21874d2490331233b3242085f8151e166 upstream.

Currently, group entity load-weights are initialized to zero. This
admits some races with respect to the first time they are re-weighted in
earlty use. ( Let g[x] denote the se for "g" on cpu "x". )

Suppose that we have root->a and that a enters a throttled state,
immediately followed by a[0]->t1 (the only task running on cpu[0])
blocking:

  put_prev_task(group_cfs_rq(a[0]), t1)
  put_prev_entity(..., t1)
  check_cfs_rq_runtime(group_cfs_rq(a[0]))
  throttle_cfs_rq(group_cfs_rq(a[0]))

Then, before unthrottling occurs, let a[0]->b[0]->t2 wake for the first
time:

  enqueue_task_fair(rq[0], t2)
  enqueue_entity(group_cfs_rq(b[0]), t2)
  enqueue_entity_load_avg(group_cfs_rq(b[0]), t2)
  account_entity_enqueue(group_cfs_ra(b[0]), t2)
  update_cfs_shares(group_cfs_rq(b[0]))
  < skipped because b is part of a throttled hierarchy >
  enqueue_entity(group_cfs_rq(a[0]), b[0])
  ...

We now have b[0] enqueued, yet group_cfs_rq(a[0])->load.weight == 0
which violates invariants in several code-paths. Eliminate the
possibility of this by initializing group entity weight.

Signed-off-by: Paul Turner <pjt@google.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20131016181627.22647.47543.stgit@sword-of-the-dawn.mtv.corp.google.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Chris J Arges <chris.j.arges@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

sched: Fix hrtimer_cancel()/rq->lock deadlock

commit 927b54fccbf04207ec92f669dce6806848cbec7d upstream.

__start_cfs_bandwidth calls hrtimer_cancel while holding rq->lock,
waiting for the hrtimer to finish. However, if sched_cfs_period_timer
runs for another loop iteration, the hrtimer can attempt to take
rq->lock, resulting in deadlock.

Fix this by ensuring that cfs_b->timer_active is cleared only if the
_latest_ call to do_sched_cfs_period_timer is returning as idle. Then
__start_cfs_bandwidth can just call hrtimer_try_to_cancel and wait for
that to succeed or timer_active == 1.

Signed-off-by: Ben Segall <bsegall@google.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: pjt@google.com
Link: http://lkml.kernel.org/r/20131016181622.22647.16643.stgit@sword-of-the-dawn.mtv.corp.google.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Chris J Arges <chris.j.arges@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

sched: Fix cfs_bandwidth misuse of hrtimer_expires_remaining

commit db06e78cc13d70f10877e0557becc88ab3ad2be8 upstream.

hrtimer_expires_remaining does not take internal hrtimer locks and thus
must be guarded against concurrent __hrtimer_start_range_ns (but
returning HRTIMER_RESTART is safe). Use cfs_b->lock to make it safe.

Signed-off-by: Ben Segall <bsegall@google.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: pjt@google.com
Link: http://lkml.kernel.org/r/20131016181617.22647.73829.stgit@sword-of-the-dawn.mtv.corp.google.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Chris J Arges <chris.j.arges@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

sched: Fix race on toggling cfs_bandwidth_used

commit 1ee14e6c8cddeeb8a490d7b54cd9016e4bb900b4 upstream.

When we transition cfs_bandwidth_used to false, any currently
throttled groups will incorrectly return false from cfs_rq_throttled.
While tg_set_cfs_bandwidth will unthrottle them eventually, currently
running code (including at least dequeue_task_fair and
distribute_cfs_runtime) will cause errors.

Fix this by turning off cfs_bandwidth_used only after unthrottling all
cfs_rqs.

Tested: toggle bandwidth back and forth on a loaded cgroup. Caused
crashes in minutes without the patch, hasn't crashed with it.

Signed-off-by: Ben Segall <bsegall@google.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: pjt@google.com
Link: http://lkml.kernel.org/r/20131016181611.22647.80365.stgit@sword-of-the-dawn.mtv.corp.google.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Chris J Arges <chris.j.arges@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

x86, fpu, amd: Clear exceptions in AMD FXSAVE workaround

commit 26bef1318adc1b3a530ecc807ef99346db2aa8b0 upstream.

Before we do an EMMS in the AMD FXSAVE information leak workaround we
need to clear any pending exceptions, otherwise we trap with a
floating-point exception inside this code.

Reported-by: halfdog <me@halfdog.net>
Tested-by: Borislav Petkov <bp@suse.de>
Link: http://lkml.kernel.org/r/CA%2B55aFxQnY_PCG_n4=0w-VG=YLXL-yr7oMxyy0WU2gCBAf3ydg@mail.gmail.com
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

netfilter: nf_nat: fix access to uninitialized buffer in IRC NAT helper

commit 2690d97ade05c5325cbf7c72b94b90d265659886 upstream.

Commit 5901b6be885e attempted to introduce IPv6 support into
IRC NAT helper. By doing so, the following code seemed to be removed
by accident:

  ip = ntohl(exp->master->tuplehash[IP_CT_DIR_REPLY].tuple.dst.u3.ip);
  sprintf(buffer, "%u %u", ip, port);
  pr_debug("nf_nat_irc: inserting '%s' == %pI4, port %u\n", buffer, &ip, port);

This leads to the fact that buffer[] was left uninitialized and
contained some stack value. When we call nf_nat_mangle_tcp_packet(),
we call strlen(buffer) on excatly this uninitialized buffer. If we
are unlucky and the skb has enough tailroom, we overwrite resp. leak
contents with values that sit on our stack into the packet and send
that out to the receiver.

Since the rather informal DCC spec [1] does not seem to specify
IPv6 support right now, we log such occurences so that admins can
act accordingly, and drop the packet. I've looked into XChat source,
and IPv6 is not supported there: addresses are in u32 and print
via %u format string.

Therefore, restore old behaviour as in IPv4, use snprintf(). The
IRC helper does not support IPv6 by now. By this, we can safely use
strlen(buffer) in nf_nat_mangle_tcp_packet() and prevent a buffer
overflow. Also simplify some code as we now have ct variable anyway.

  [1] http://www.irchelp.org/irchelp/rfc/ctcpspec.html

Fixes: 5901b6be885e ("netfilter: nf_nat: support IPv6 in IRC NAT helper")
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Harald Welte <laforge@gnumonks.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

netfilter: fix wrong byte order in nf_ct_seqadj_set internal information

commit 23dfe136e2bf8d9ea1095704c535368a9bc721da upstream.

In commit 41d73ec053d2, sequence number adjustments were moved to a
separate file. Unfortunately, the sequence numbers that are stored
in the nf_ct_seqadj structure are expressed in host byte order. The
necessary ntohl call was removed when the call to adjust_tcp_sequence
was collapsed into nf_ct_seqadj_set. This broke the FTP NAT helper.
Fix it by adding back the byte order conversions.

Reported-by: Dawid Stawiarski <dawid.stawiarski@netart.pl>
Signed-off-by: Phil Oester <kernel@linuxace.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

SCSI: sd: Reduce buffer size for vpd request

commit af73623f5f10eb3832c87a169b28f7df040a875b upstream.

Somehow older areca firmware versions have issues with
scsi_get_vpd_page() and a large buffer, the firmware
seems to crash and the scsi error-handler will start endless
recovery retries.
Limiting the buf-size to 64-bytes fixes this issue with older
firmware versions (<1.49 for my controller).

Fixes a regression with areca controllers and older firmware versions
introduced by commit: 66c28f97120e8a621afd5aa7a31c4b85c547d33d

Reported-by: Nix <nix@esperi.org.uk>
Tested-by: Nix <nix@esperi.org.uk>
Signed-off-by: Bernd Schubert <bernd.schubert@itwm.fraunhofer.de>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

intel_pstate: Add X86_FEATURE_APERFMPERF to cpu match parameters.

commit 6cbd7ee10e2842a3d1f9b60abede1c8f3d1f1130 upstream.

KVM environments do not support APERF/MPERF MSRs. intel_pstate cannot
operate without these registers.

The previous validity checks in intel_pstate_msrs_not_valid() are
insufficent in nested KVMs.

References: https://bugzilla.redhat.com/show_bug.cgi?id=1046317
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mac80211: move "bufferable MMPDU" check to fix AP mode scan

commit 277d916fc2e959c3f106904116bb4f7b1148d47a upstream.

The check needs to apply to both multicast and unicast packets,
otherwise probe requests on AP mode scans are sent through the multicast
buffer queue, which adds long delays (often longer than the scanning
interval).

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ACPI / Battery: Add a _BIX quirk for NEC LZ750/LS

commit a90b40385735af0d3031f98e97b439e8944a31b3 upstream.

The AML method _BIX of NEC LZ750/LS returns a broken package which
skips the first member "Revision" (ACPI 5.0, Table 10-234).

Add a quirk for this machine to skip member "Revision" during parsing
the package returned by _BIX.

Reference: https://bugzilla.kernel.org/show_bug.cgi?id=67351
Reported-and-tested-by: Francisco Castro <fcr@adinet.com.uy>
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ACPI / TPM: fix memory leak when walking ACPI namespace

commit df45c712d1f4ef37714245fb75de726f4ca2bf8d upstream.

In function ppi_callback(), memory allocated by acpi_get_name() will get
leaked when current device isn't the desired TPM device, so fix the
memory leak.

Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>