Ye Li [Wed, 17 Apr 2019 09:41:20 +0000 (09:41 +0000)]
mxc_ocotp: Update redundancy banks for mx7ulp B0
On mx7ulp B0, beside bank 0 and 1, the fuse bank 9, 10, 28 are changed to
Redundancy mode not ECC, so they can support to program different bits of
a word in multiple times.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Wed, 17 Apr 2019 09:41:16 +0000 (09:41 +0000)]
imx: i.MX8MQ: clear ocotp error bit
In case ocotp error bit is set, clear it.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Mon, 15 Apr 2019 12:00:50 +0000 (12:00 +0000)]
imx: 8qxp_mek: fix fdt_file and console
Fix fdt_file and console to boot upstream Linux Kernel.
Upstream linux use imx8qxp-mek.dtb, and pass lpuart32 to earlycon
will not work for i.MX8QXP, only need to pass earlycon,
check drivers/tty/serial/earlycon.c,
" /* Just 'earlycon' is a valid param for devicetree and ACPI SPCR. */ "
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Ludwig Zenz [Mon, 15 Apr 2019 09:13:08 +0000 (11:13 +0200)]
ARM: imx6: DHCOM i.MX6 PDK: use Kconfig for inclusion of DDR calibration
The four x16 DDR3 are wired in T-topology. From NXP AN4467:
'Although not required, T-Topologies may also benefit from performing
Write Leveling as there are package delays on both the processor and DDR
devices that can be de-skewed by performing Write Leveling. Therefore,
Freescale recommends determining Write Leveling calibration parameters
for all boards, regardless of topology used.'
That is why write level calibration is also done.
Signed-off-by: Ludwig Zenz <lzenz@dh-electronics.com>
Ludwig Zenz [Mon, 15 Apr 2019 07:31:10 +0000 (09:31 +0200)]
ARM: imx6: update 1GB DDR3 calibration for DHCOM i.MX6qd PDK
The existing calibration values were found to be incorrect
in comparison to newly determined values.
The new values were generated with the help of 5 boards. They have
been determined with the NXP Utility 'DDR Stress Test (2.9.0)'.
Signed-off-by: Ludwig Zenz <lzenz@dh-electronics.com>
Peng Fan [Mon, 15 Apr 2019 05:20:43 +0000 (05:20 +0000)]
imx: add lowlevel init for ARM64
Sometimes we met SERROR, but only to catch it when Linux boots up.
Let's enable catching in U-Boot to catch it ealier and ease debug.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Chris Packham [Sat, 13 Apr 2019 08:21:48 +0000 (20:21 +1200)]
ARM: imx: Fix typo in select option for ZMX25
Correct CPU_ARM926EJS1 to CPU_ARM926EJS.
Reported-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Pierre-Jean Texier [Fri, 12 Apr 2019 20:36:36 +0000 (22:36 +0200)]
warp7: Fix dfu_alt_info setting after DM conversion
After DM conversion, U-Boot is larger than 512 KiB, so we need to increase
the "size" of the dfu_alt_info setting.
Signed-off-by: Pierre-Jean Texier <pjtexier@koncepto.io>
Acked-by: Joris Offouga <offougajoris@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Filip Brozovic [Fri, 12 Apr 2019 09:59:55 +0000 (11:59 +0200)]
dts: imx6ull: add USB aliases to support DM
Signed-off-by: Filip Brozovic <fbrozovic@gmail.com>
Stefano Babic [Thu, 25 Apr 2019 14:25:03 +0000 (16:25 +0200)]
imx8qxp_mek: drop warning due to unused variable
Signed-off-by: Stefano Babic <sbabic@denx.de>
Joris Offouga [Thu, 4 Apr 2019 12:00:56 +0000 (14:00 +0200)]
pico-imx7d: Increase u-boot size for dfu request
After DM conversion, the size of U-Boot binary to increase.
Previous size is 480K after DM Conversion the new size is 557K
So it's necessary to increase the dfu request for store u-boot-dtb.img in eMMC.
Signed-off-by: Joris Offouga <offougajoris@gmail.com>
Joris Offouga [Thu, 4 Apr 2019 12:00:55 +0000 (14:00 +0200)]
pico-imx7d: Convert DM MMC
This patch enable convert DM MMC for imx7d-pico board and variant.
Before the DM conversion only usdhc3 was enabled and therefore it appeared
as MMC 0 to u-boot. After enabling MMC DM though usdhc3 defaults to MMC 2,
which left unattended would drive changes to existing pico-pi bootscripts and
environment variables that rely on mmc 0.
Setup the alias of mmc0 and usdhc3 so that existing pico-imx7d boot code will
work unmodified.
When converting to DM_MMC it is necessary that SPL initializes eMMC
by itself, so move the original eMMC initialization from U-Boot
proper to SPL.
Signed-off-by: Joris Offouga <offougajoris@gmail.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Marcel Ziswiler [Tue, 9 Apr 2019 15:25:33 +0000 (17:25 +0200)]
board: toradex: tdx-cfg-block: add new skus
Add all the latest new SKUs:
- Apalis iMX8 QuadXPlus 2GB Wi-Fi / BT IT
- Apalis iMX8 QuadMax 4GB IT
- Apalis iMX8 QuadPlus 2GB Wi-Fi / BT
- Apalis iMX8 QuadPlus 2GB",
- Colibri iMX8 QuadXPlus 2GB IT
- Colibri iMX8 DualX 1GB Wi-Fi / Bluetooth
- Colibri iMX8 DualX 1GB
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Joris Offouga [Thu, 4 Apr 2019 12:00:54 +0000 (14:00 +0200)]
pico-imx7d: defconfig Enable DM gpio pinctrl and pinctrl_imx7
This patch is necessary for convert this board to dm driver model
DM GPIO requires gpio_request() to be called explicitly before
doing any gpio operation
Signed-off-by: Joris Offouga <offougajoris@gmail.com>
Marcel Ziswiler [Tue, 9 Apr 2019 15:25:32 +0000 (17:25 +0200)]
board: toradex: tdx-cfg-block: clean-up sku handling
Clean-up handling of several SKUs.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Joris Offouga [Thu, 4 Apr 2019 12:00:53 +0000 (14:00 +0200)]
pico-imx7d: defconfig: Add DT file hooks
This patch adds DT file hooks for Pico i.MX7D SOM and variant boards
Signed-off-by: Joris Offouga <offougajoris@gmail.com>
Marcel Ziswiler [Tue, 9 Apr 2019 15:25:31 +0000 (17:25 +0200)]
arm: dts: imx8dx: add lpuart1, lpuart2, lpuart3
Add support for lpuart1, lpuart2 and lpuart3.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Marcel Ziswiler [Tue, 9 Apr 2019 15:25:30 +0000 (17:25 +0200)]
misc: imx8: remove duplicates from scfw api
Remove duplicate function declarations from the SCFW API header file.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Joris Offouga [Thu, 4 Apr 2019 12:00:52 +0000 (14:00 +0200)]
Arm: imx7d-pico: Import all Linux device tree for Pico i.MX7D SOM
This patch imports the Linux kernel base board imx7d-pico.dtsi,
pi board imx7d-pico-pi.dts and hobbit board imx7d-pico-hobbit.dts
from Linux v5.1-rc1.
Signed-off-by: Joris Offouga <offougajoris@gmail.com>
Marcel Ziswiler [Tue, 9 Apr 2019 15:24:18 +0000 (17:24 +0200)]
ARM: dts: colibri-imx6ull: fix uart-has-rtscts property
Remove vendor pre-fix fsl, from uart-has-rtscts property.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Marcel Ziswiler [Tue, 9 Apr 2019 15:24:17 +0000 (17:24 +0200)]
colibri-imx6ull: migrate fec to using driver model
Migrate Ethernet FEC to using driver model.
Drop PHY_MICREL_KSZ90X1 which slipped in from Apalis iMX6.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Marcel Ziswiler [Tue, 9 Apr 2019 15:24:16 +0000 (17:24 +0200)]
colibri-imx6ull: migrate usb to using driver model
Migrate USB to using driver model.
Add USBH_PEN GPIO regulator.
While at it also add alias e.g. as required for UMS.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Marcel Ziswiler [Tue, 9 Apr 2019 15:24:15 +0000 (17:24 +0200)]
colibri-imx6ull: migrate mmc to using driver model
Migrate MMC to using driver model.
Migrate USDHC to using pinctrl.
While at it also add GPIO1_IO03__OSC32K_32K_OUT pin muxing.
While at it also update copyright period.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Marcel Ziswiler [Tue, 9 Apr 2019 15:24:14 +0000 (17:24 +0200)]
colibri-imx6ull: migrate pinctrl and regulators to dtb/dm
Migrate pinctrl and regulators to device tree resp. driver model:
Ethernet, NAND and UART.
Drop BOARD_EARLY_INIT_F as it is anyway no longer used.
Enable CMD_DM, CMD_MTD, CMD_REGULATOR and DM_REGULATOR_FIXED.
While at it also update copyright period.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Marcel Ziswiler [Tue, 9 Apr 2019 15:24:13 +0000 (17:24 +0200)]
colibri-imx6ull: configuration clean-up
Drop disabling SPL_SYS_THUMB_BUILD as we anyway do not use SPL.
Enbale CRC32 verify, USB SDP and EFI loader support.
Drop CMD_GPT and disabling RANDOM_UUID.
Do savedefconfig which drops USB_FUNCTION_SDP.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Philippe Schenker [Tue, 9 Apr 2019 15:24:12 +0000 (17:24 +0200)]
board: imx6ull: Add disable PMIC_STBY_REQ
Disable output driver of PAD CCM_PMIC_STBY_REQ. This prevents the
SOC to request for a lower voltage during sleep. This is necessary
because the voltage is changing too slow for the SOC to wake up
properly.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Marcel Ziswiler [Tue, 9 Apr 2019 15:24:11 +0000 (17:24 +0200)]
colibri-imx6ull: fix ethernet phy power on
Just give the new Ethernet PHY power save mode circuitry time to settle.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Stefan Agner [Tue, 9 Apr 2019 15:24:10 +0000 (17:24 +0200)]
apalis/colibri_imx6/imx6ull: make sure loadaddr does not collide
Currently $loadaddr and $fdt_addr_r point to the same address. This
might be not ideal for some distro boot scripts which make use of
$loadaddr after loading the device tree.
Make sure the two variables point to two different addresses. Moving
$loadaddr is not entirly trivial since it is defined in mx6_common.h.
Move $fdt_addr_r and $ramdisk_addr_r by 1MiB, which should be enough
for scripts.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Stefan Agner [Tue, 9 Apr 2019 15:24:09 +0000 (17:24 +0200)]
colibri-imx6ull: set module variant depending on config block
Using CPU temperature grading as a discriminator if the Wi-Fi /
Bluetooth chip is populated is no longer possible due to upcoming
SKUs. Set variant to -wifi only if a valid config block is present
and the product id mentions a SKU with Wi-Fi / Bluetooth.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Stefan Agner [Tue, 9 Apr 2019 15:24:08 +0000 (17:24 +0200)]
tdx-cfg-block: simplify i.MX 6 module detection
Use CONFIG_TARGET_... at compile time to differentiate between
Apalis iMX6, Colibri iMX6 and Colibri iMX6ULL. Avoid code
duplication by moving question about Wi-Fi / Bluetooth before
IT/non-IT decision.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Gerard Salvatella [Tue, 9 Apr 2019 15:24:07 +0000 (17:24 +0200)]
tdx-cfg-block: add support for new colibri iMX6ull skus
Add support for new Colibri iMX6ULL SKUs.
While at it also checkpatch fix the whole files.
Signed-off-by: Gerard Salvatella <gerard.salvatella@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Marcel Ziswiler [Thu, 28 Mar 2019 22:25:15 +0000 (23:25 +0100)]
colibri_vf: fix tab vs. spaces
Fix indentation using tab vs. spaces.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Marcel Ziswiler [Thu, 28 Mar 2019 22:24:50 +0000 (23:24 +0100)]
colibri_vf: fix ethernet by adding explicit phy node
The implicit fallback mechanism for searching the whole MDIO bus for at
least one PHY has been gone with the following commit
b882005a18de
("drivers/net/fec: phy_init: remove redundant logic"). This lead to the
Ethernet driver erroring out as follows:
Net: Could not get PHY for FEC0: addr -19
eth-1: fec@
400d1000
Colibri VFxx # dhcp
Could not get PHY for FEC0: addr -19
Could not get PHY for FEC0: addr -19
Could not get PHY for FEC0: addr -19
Could not get PHY for FEC0: addr -19
No ethernet found.
Could not get PHY for FEC0: addr -19
Colibri VFxx #
This commit adds an explicit PHY node which makes it work again.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Peng Fan [Tue, 5 Mar 2019 02:32:49 +0000 (02:32 +0000)]
imx: support i.MX8QM MEK board
Add i.MX8QM MEK board support.
Included a basic dts, enabled SPL FIT
Boot log as below:
U-Boot SPL 2019.01-rc1-00029-gf002213219 (Dec 24 2018 - 10:28:30 +0800)
Normal Boot
Trying to boot from MMC2_2
U-Boot 2019.01-rc1-00029-gf002213219 (Dec 24 2018 - 10:28:30 +0800)
CPU: NXP i.MX8QM RevB A53 at 142933 MHz
Model: Freescale i.MX8QM MEK
Board: iMX8QM MEK
Build: SCFW
9330215b
Boot: SD1
DRAM: 6 GiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
Loading Environment from MMC... *** Warning - bad CRC, using default environment
In: serial@
5a060000
Out: serial@
5a060000
Err: serial@
5a060000
Net:
Error: ethernet@
5b040000 address not set.
eth-1: ethernet@
5b040000
Hit any key to stop autoboot: 0
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Tue, 5 Mar 2019 02:32:45 +0000 (02:32 +0000)]
misc: imx8: scu: add i.MX8QM support
According to IMX8QXP/8QM config option, choose the clk/iomuxc
compatible.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Tue, 5 Mar 2019 02:32:39 +0000 (02:32 +0000)]
imx8: imx8-pins: add i.MX8QM
Add i.MX8QM entry
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Tue, 5 Mar 2019 02:32:35 +0000 (02:32 +0000)]
clk: imx8: add i.MX8QM clk driver
Add i.MX8QM clk driver, SDHC/FEC/UART/I2C supported.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Tue, 5 Mar 2019 02:32:33 +0000 (02:32 +0000)]
clk: imx8: split code into common and soc specific part
To make it easy to add new clk driver for i.MX8, split
the code into common part and SoC specific part.
Make the get/set/enable non static and introduce a num_clks for
soc_clk_dump, because the arrays are moved to clk-imx8qxp.c.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Tue, 5 Mar 2019 02:32:28 +0000 (02:32 +0000)]
imx8: add cpu support
Add cpu type and Kconfig entry
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Tue, 5 Mar 2019 02:32:25 +0000 (02:32 +0000)]
arm: dts: introduce dtsi for i.MX8QM
Introduce basic dtsi for i.MX8QM, only support SDHC/FEC/LPUART.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Tue, 5 Mar 2019 02:32:21 +0000 (02:32 +0000)]
dt-bindings: clock: dt-bindings: pinctrl: add i.MX8QM clocks definition
Add i.MX8QM clocks definition
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Tue, 5 Mar 2019 02:32:17 +0000 (02:32 +0000)]
dt-bindings: pinctrl: add i.MX8QM pads definition
Add i.MX8QM pads definition
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Tue, 5 Mar 2019 02:32:13 +0000 (02:32 +0000)]
pinctrl: imx8: add i.MX8QM compatible
Add i.MX8QM compatible
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Lukasz Majewski [Thu, 4 Apr 2019 10:26:56 +0000 (12:26 +0200)]
boot.src: Provide dsa_core.blacklist bootarg when booting via NFS
This setup is a bit special as Linux kernel (4.19) is not supporting
in-kernel NFS rootfs mount and Distributed Switch Architecture (DSA)
operation.
For that reason it was necessary to provide a bootarg to allow userspace
enable it afterwards if needed.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Lukasz Majewski [Thu, 4 Apr 2019 10:26:55 +0000 (12:26 +0200)]
Convert CONFIG_USB_EHCI_MX5 to Kconfig
This converts the following to Kconfig:
CONFIG_USB_EHCI_MX5
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Lukasz Majewski [Thu, 4 Apr 2019 10:26:54 +0000 (12:26 +0200)]
ARM: config: Remove not needed CONFIG_MXC_USB_PORT define
After i.MX5's EHCI conversion to DM, the CONFIG_MXC_USB_PORT is not needed
anymore and should be removed.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Lukasz Majewski [Thu, 4 Apr 2019 10:26:53 +0000 (12:26 +0200)]
ARM: defconfig: kp_imx53: Enable DM_USB support on HSC|DDC boards
This commit enables the DM_USB on HSC|DDC i.MX53 based boards.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Lukasz Majewski [Thu, 4 Apr 2019 10:26:52 +0000 (12:26 +0200)]
USB: DM: Convert i.MX5 ehci code to driver model
This commit converts i.MX5's EHCI USB host driver to driver model (DM_USB).
It is a straightforward conversion (to reuse as much code as possible),
based on ehci-mx6.c code.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Lukasz Majewski [Thu, 4 Apr 2019 10:26:51 +0000 (12:26 +0200)]
ARM: Remove EHCI specific code from HSC|DDC board file
As EHCI on i.MX5 has been converted to driver model, the board specific
code, necessary for VBUS USB power supply setup is not needed anymore.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Lukasz Majewski [Thu, 4 Apr 2019 10:26:50 +0000 (12:26 +0200)]
DTS: Enable USB host support (including regulators) on HSC|DDC boards
This commit enables the support for K&P's HSC|DDC imx53 based boards.
It was also necessary to provide device tree description for regulators
to avoid board specific code definition.
The GPIO pin description responsible for VBUS control has been moved from
"hog" group to usbh1 dedicated one.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Lukasz Majewski [Thu, 4 Apr 2019 10:26:49 +0000 (12:26 +0200)]
DTS: Provide USB host DTS description for i.MX53 devices
This code has been ported from Linux kernel - tag v5.1-rc2.
The difference from the kernel is the removal of:
fsl,usbmisc = <&usbmisc 1>;
fsl,usbphy = <&usbphy1>;
properties, which are not needed for correct u-boot operation (as PHY
setup is done in ehci-mx5.c file itself).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Lukasz Majewski [Thu, 4 Apr 2019 10:26:48 +0000 (12:26 +0200)]
ARM: kp_imx53: config: Do not use ${boardtype} to setup update wic file
After unification of the rootfs for both HSC and DDC devices, only one,
common wic file is necessary - without the distinction of specific board.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Lukasz Majewski [Thu, 4 Apr 2019 10:26:47 +0000 (12:26 +0200)]
ARM: Remove non DM/DTS esdhc3 code from HSC|DDC board related files
After switching to DM/DTS support of esdhc3 - the code in this patch
can be removed.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Lukasz Majewski [Thu, 4 Apr 2019 10:26:46 +0000 (12:26 +0200)]
ARM: defconfig: Move CONFIG_FSL_ESDHC to Kconfig
The CONFIG_FSL_ESDHC is now enabled and defined in Kconfig, not in
include/configs/kp_imx53.h
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Lukasz Majewski [Thu, 4 Apr 2019 10:26:45 +0000 (12:26 +0200)]
ARM: Enable CONFIG_DM_MMC and CONFIG_DM_BLK on HSC and DDC boards
This commit enables DM_MMC and DM_BLK on imx53 based HSC and DDC boards.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Lukasz Majewski [Thu, 4 Apr 2019 10:26:44 +0000 (12:26 +0200)]
DTS: Add esdhc3 device tree description tuning for HSC|DDC boards
In this commit the esdhc3 controller is enabled as well as it is remaped
to mmc0 to not break legacy code.
The pinctrl setup (e.g. 0x1e4) is the same as one from in-board file
definition.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Lukasz Majewski [Thu, 4 Apr 2019 10:26:43 +0000 (12:26 +0200)]
ARM: Remove HSC|DDC ETH PHY reset code after switching to DM/DTS
After commit
efd0b791069a ("eth: dm: fec: Add gpio phy reset binding")
the in-board file definition of ETH PHY reset can be removed.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Peng Fan [Thu, 7 Mar 2019 12:43:37 +0000 (12:43 +0000)]
imx8qxp: mek: enable dm-spl for pm
with u-boot,dm-spl added for imx8qx-pm node, and SPL_SIMPLE_BUS enabled,
the bind and probe code in board file could be removed.
Also we need to enlarge SYS_MALLOC_F_LEN to avoid calloc fail.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Adam Ford [Thu, 11 Apr 2019 20:24:33 +0000 (15:24 -0500)]
ARM: omap3_logic: Enable UUID
Instead of hardcoding the mmcroot to /dev/mmcblkX, use the UUID
method.
Signed-off-by: Adam Ford <aford173@gmail.com>
Adam Ford [Thu, 11 Apr 2019 18:44:59 +0000 (13:44 -0500)]
ARM: imx6q_logic: Allow storing environment in FAT on eMMC
Some variations of the imx6q_logic board have eMMC instead of
NAND. Rather than creating a separate defconfig, this patch
adds the ability to read/write to eMMC (mmc 0:1) when NAND
doesn't exist.
Signed-off-by: Adam Ford <aford173@gmail.com>
Adam Ford [Thu, 11 Apr 2019 18:46:09 +0000 (13:46 -0500)]
ARM: imx6q_logic: Allow optional arguments to cmd line
This adds an extra, optional environmental variable called
'optargs' which if enabled allow additional parameters to be
passed to the kernel (ie, quiet, cma=128M, etc.)
Each script that setups the bootargs will just append this.
Signed-off-by: Adam Ford <aford173@gmail.com>
Peng Fan [Fri, 12 Apr 2019 07:55:12 +0000 (07:55 +0000)]
imx8: mek: move HUSH_PARSER to defconfig
Move HUSH_PARSER to defconfig, otherwise meet
"
=> run netboot
Booting from net ...
Unknown command 'if' - try 'help'
Unknown command 'then' - try 'help'
Unknown command 'else' - try 'help'
Unknown command 'fi' - try 'help'
Unknown command '0x80280000' - try 'help'
Unknown command 'if' - try 'help'
Unknown command 'then' - try 'help'
Unknown command 'then' - try 'help'
Unknown command 'else' - try 'help'
Unknown command 'fi' - try 'help'
Unknown command 'else' - try 'help'
Unknown command 'fi' - try 'help'
"
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Fri, 12 Apr 2019 07:54:57 +0000 (07:54 +0000)]
imx8qxp: mek: Enable CMD_FUSE
Enable CMD_FUSE for i.MX8QXP MEK
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Fri, 12 Apr 2019 07:54:54 +0000 (07:54 +0000)]
imx8: fuse: add fuse driver
Add fuse write for i.MX8
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Fri, 12 Apr 2019 07:54:50 +0000 (07:54 +0000)]
imx: sip: add call_imx_sip_ret2
This function will be used by i.MX8 fuse driver.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Tom Rini [Wed, 24 Apr 2019 13:04:23 +0000 (09:04 -0400)]
Merge branch '2019-04-22-master-imports'
- Add and enable brcmnand driver on a number of relevant platforms.
Also add and enable LED drivers on more bcm platforms.
- Various ARMv8 fixes/improvements, including extending PSCI
functionality.
- fs_loader improvments
- Various FIT/SPL improvements
- PCI bugfixes
- Poplar platform ethernet support
- MediaTek MMC improvements
- Android boot improvements
Eugeniu Rosca [Mon, 8 Apr 2019 15:35:28 +0000 (17:35 +0200)]
image: android: fix 'iminfo' typo
Fix below CP warning triggered by the 'iminfo' output in another patch:
WARNING: 'addrress' may be misspelled - perhaps 'address'?
Fixes:
4f1318b29c7a20 ("common: image: minimal android image iminfo support")
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Eugeniu Rosca [Mon, 8 Apr 2019 15:35:27 +0000 (17:35 +0200)]
image: android: allow booting lz4-compressed kernels
According to Android image format [1], kernel image resides at 1 page
offset from the boot image address. Grab the magic number from there
and allow U-Boot to handle LZ4-compressed KNL binaries instead of
hardcoding compression type to IH_COMP_NONE. Other compression types,
if needed, can be added later.
Tested on H3ULCB-KF using the image detailed in [2].
[1] Excerpt from include/android_image.h
+-----------------+
| boot header | 1 page
+-----------------+
| kernel | n pages
+-----------------+
| ramdisk | m pages
+-----------------+
| second stage | o pages
+-----------------+
[2] => iminfo
4c000000
## Checking Image at
4c000000 ...
Android image found
kernel size: 85b9d1
kernel address:
48080000
ramdisk size: 54ddbc
ramdisk addrress:
4a180000
second size: 0
second address:
48000800
tags address:
48000100
page size: 800
os_version:
1200012a (ver: 0.9.0, level: 2018.10)
name:
cmdline: buildvariant=userdebug
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Heinrich Schuchardt [Sun, 7 Apr 2019 15:57:40 +0000 (17:57 +0200)]
test: env: Enable env unit tests by default
If CONFIG_UNIT_TEST is enabled we should enable the individual tests by
default to ensure good test coverage.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Lars Povlsen [Thu, 4 Apr 2019 12:38:50 +0000 (14:38 +0200)]
ARMv8: PSCI: Fix PSCI_TABLE relocation issue
This fixes relaction isses with the PSCI_TABLE entries in
the psci_32_table and psci_64_table.
When using 32-bit adress pointers relocation was not being applied to
the tables, causing PSCI handlers to point to the un-relocated code
area. By using 64-bit data relocation is properly applied. The
handlers are thus in the "secure data" area, which is protected by
/memreserve/ in the FDT.
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Trent Piepho [Wed, 27 Mar 2019 23:50:09 +0000 (23:50 +0000)]
bootm: Simplying cache flush code
The cache flush of the kernel load area needs to be aligned outward to
the DMA cache alignment. The operations are simpler if we think of this
as aligning the start down, ALIGN_DOWN(load, ARCH_DMA_MINALIGN), and
aligning the end up, ALIGN(load_end, ARCH_DMA_MINALIGN), and then find
the length of the flushed region by subtracting the former from the
latter.
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Andreas Dannenberg [Wed, 27 Mar 2019 18:17:26 +0000 (13:17 -0500)]
malloc: Fix memalign not honoring alignment prior to full malloc init
When using memalign() in a scenario where U-Boot is configured for full
malloc support with simple malloc not explicitly enabled and before the
full malloc support is initialized, a memory block is being allocated
and returned without the alignment parameter getting honored.
Fix this issue by replacing the existing memalign pre-full malloc init
logic with a call to memalign_simple() this way ensuring proper alignment
of the returned memory block.
Fixes:
ee038c58d519 ("malloc: Use malloc simple before malloc is fully initialized in memalign()")
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Stefan Roese [Tue, 26 Mar 2019 12:04:00 +0000 (13:04 +0100)]
spl: spl_nand.c: Add NAND loading message
This patch adds a short message to the SPL NAND loader, which displays
the source and destinations addresses including the size of the
loaded image, like this:
U-Boot SPL 2019.04-rc3-00113-g486efd8aaf (Mar 15 2019 - 14:18:02 +0100)
Trying to boot from NAND
Loading U-Boot from 0x00040000 (size 0x000a0000) to 0x22900000
I find this message quite helpful - hopefully others do so as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Fabien Parent [Sun, 24 Mar 2019 15:46:38 +0000 (16:46 +0100)]
ARM: MediaTek: Add support for MT8516 SoC
Add support for MediaTek MT8516 SoC. This include the file
that will initialize the SoC after boot and its device tree.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Fabien Parent [Sun, 24 Mar 2019 15:46:37 +0000 (16:46 +0100)]
pinctrl: add driver for MT8516
Add Pinctrl driver for MediaTek MT8516 SoC.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Acked-by: Ryder Lee <ryder.lee@mediatek.com>
Fabien Parent [Sun, 24 Mar 2019 15:46:36 +0000 (16:46 +0100)]
clk: mediatek: add driver for MT8516
Add clock driver for MediaTek MT8516 SoC.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Acked-by: Ryder Lee <ryder.lee@mediatek.com>
[trini: Redo whitespace]
Signed-off-by: Tom Rini <trini@konsulko.com>
Fabien Parent [Sun, 24 Mar 2019 15:46:35 +0000 (16:46 +0100)]
clk: mediatek: add support for SETCLR_INV and NO_SETCLR flags
Add the implementation for the CLK_GATE_SETCLR_INV and
CLK_GATE_NO_SETCLR flags.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Acked-by: Ryder Lee <ryder.lee@mediatek.com>
Fabien Parent [Sun, 24 Mar 2019 15:46:34 +0000 (16:46 +0100)]
mmc: mtk-sd: fix configuration option check
We either need to use IS_ENABLED(CONFIG_FOO) or CONFIG_IS_ENABLED(FOO).
IS_ENABLE(FOO) will always return false.
This commit fixes the comparison by using the CONFIG_IS_ENABLED(FOO)
syntax.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Fabien Parent [Sun, 24 Mar 2019 15:46:33 +0000 (16:46 +0100)]
mmc: mtk-sd: add support for MT8516
Add config for handling MT8516 SoC.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Acked-by: Ryder Lee <ryder.lee@mediatek.com>
Fabien Parent [Sun, 24 Mar 2019 15:46:32 +0000 (16:46 +0100)]
mmc: mtk-sd: add source_cg clock support
Some MediaTek SoC need an additional clock "source_cg". Enable
this new clock. We reuse the same clock name as in the kernel.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Acked-by: Ryder Lee <ryder.lee@mediatek.com>
Shawn Guo [Wed, 20 Mar 2019 07:32:41 +0000 (15:32 +0800)]
poplar: enable Ethernet driver support
The 'phy' reset of gmac device in kernel device tree is not generic
enough for u-boot to use, so we need to overwrite the 'resets' property
as needed. With this device tree fixup and poplar_defconfig changes,
Ethernet starts working on Poplar board.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Shawn Guo [Wed, 20 Mar 2019 07:32:40 +0000 (15:32 +0800)]
net: add higmacv300 Ethernet driver for HiSilicon platform
It adds the driver for HIGMACV300 Ethernet controller found on HiSilicon
SoCs like Hi3798CV200. It's based on a downstream U-Boot driver, but
quite a lot of code gets rewritten and cleaned up to adopt driver model
and PHY API.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Shawn Guo [Wed, 20 Mar 2019 07:32:39 +0000 (15:32 +0800)]
reset: add reset driver for HiSilicon platform
It adds a Driver Model compatible reset driver for HiSlicon platform.
The driver implements a custom .of_xlate function, and uses .data field
as reset register offset and .id field as bit shift.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Shawn Guo [Wed, 20 Mar 2019 07:32:38 +0000 (15:32 +0800)]
reset: add polarity field into struct reset_ctl
Some reset controllers support different polarities for reset operation,
so let's add a polarity field into struct reset_ctl.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Thierry Reding [Fri, 15 Mar 2019 15:32:33 +0000 (16:32 +0100)]
pci: Scale MAX_PCI_REGIONS based on CONFIG_NR_DRAM_BANKS
If a platform defines CONFIG_NR_DRAM_BANKS, each DRAM bank will be added
as a PCI region. The number of MAX_PCI_REGIONS therefore needs to scale
with the number of DRAM banks, otherwise we will end up with too little
space in the hose->regions array to store all system memory regions.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Thierry Reding [Fri, 15 Mar 2019 15:32:32 +0000 (16:32 +0100)]
pci: Add boundary check for hose->regions
Make sure that we don't overflow the hose->regions array, otherwise we
would end up overwriting the hose->region_count field and cause mayhem
to ensue. Also print an error message when we'd be overflowing because
it indicates that there aren't enough regions available and the number
needs to be increased.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Adam Ford [Fri, 15 Mar 2019 19:29:20 +0000 (14:29 -0500)]
ARM: da850evm: Remove legacy MMC code
With the migration to DM in SPL and the DT support, the
old legacy code is no longer neaded, so this patch removes it
Signed-off-by: Adam Ford <aford173@gmail.com>
Philippe Reynes [Fri, 22 Mar 2019 16:02:08 +0000 (17:02 +0100)]
bcm963158: enable led support
Enable the led support in the configuration
of the board bcm963158.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Philippe Reynes [Fri, 22 Mar 2019 16:02:07 +0000 (17:02 +0100)]
dt: bcm963158: enable led controller
Enable the led controller in the device tree
of the board bcm963158.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Philippe Reynes [Fri, 22 Mar 2019 16:02:06 +0000 (17:02 +0100)]
dt: bcm63158: add led controller
Add the led controller in the bcm63158 device tree.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Philippe Reynes [Fri, 22 Mar 2019 16:02:05 +0000 (17:02 +0100)]
led: bcm6858: allow to use this driver on ARCH_963158
Allow the led bcm6858 driver to be used on bcm63158.
They have the same led controller.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Philippe Reynes [Fri, 22 Mar 2019 16:02:04 +0000 (17:02 +0100)]
bcm968580xref: enable led support
Enable the led support in the configuration
of the board bcm968580xref.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Philippe Reynes [Fri, 22 Mar 2019 16:02:03 +0000 (17:02 +0100)]
dt: bcm968580xref: enable led controller
Enable the led controller in the device tree
of the board bcm968580xref.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Philippe Reynes [Fri, 22 Mar 2019 16:02:02 +0000 (17:02 +0100)]
dt: bcm6858: add led controller
Add the led controller in the bcm6858 device tree.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Philippe Reynes [Fri, 22 Mar 2019 16:02:01 +0000 (17:02 +0100)]
led: add initial support for bcm6858
The driver add the support of the led IP on bcm6858.
This led IP can drive up to 32 leds, and can handle
blinking.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Ibai Erkiaga [Fri, 15 Mar 2019 12:18:41 +0000 (12:18 +0000)]
arm: arm64 32bit address relocation
Current relocation code is limited to 21bit PC-relative addressing
which might not be enough for bigger code sizes. The following patch
increases the addressing to 32bit PC-relative. This feature is
specially interesting if U-Boot is build without optimiation (-O0) as
the text section is increased significativelly.
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
Marek Vasut [Thu, 14 Mar 2019 00:01:24 +0000 (01:01 +0100)]
travis: Add srecord package
At least MIPS Boston currently uses srec_cat tool to fiddle with
srecords. There will be other platforms coming, so install the
tool to prevent build problems.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Tom Rini <trini@konsulko.com>
Stefano Babic [Wed, 13 Mar 2019 08:46:45 +0000 (09:46 +0100)]
Add target to generate initial environment
The initial environment is linked to the u-boot binary. Modifying the
environment from User Space with the env tools requires that the tools
are always built together with the bootloader to be sure that they
contain the initial environment in case no environment is stored into
persistent storage or when a board boots with just the default
environment. This makes difficult for distros to provide a general
package to access the environment. A simpler way is if the tools are
generic for all boards and a configuration file is given to provide the
initial environment.
The patch just generates the initial environment by extracting it from
the compiled object. This file can then be used for tools in user space
to initialize the environment.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Marek Vasut [Wed, 6 Mar 2019 21:04:31 +0000 (22:04 +0100)]
spl: ymodem: Add support for loading full fitImages
Add support for loading fully featured fitImages over YModem in SPL.
This is useful when various advanced features of full fitImages are
needed in SPL.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Peter Ujfalusi [Wed, 6 Mar 2019 13:52:27 +0000 (15:52 +0200)]
fit: load all fragments from the extra configurations
Currently only the first fdt is loaded from the extra configuration of
FIT image.
If the configuration have multiple fdt, load them all as well.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>