[media] vivi: vivi_dev->line[] was not aligned

Though dev->line[] is u8 array we work with it as with u16, u24 or u32
pixels, and also pass it to memcpy() and it's better to align it to at
least 4.
Before the patch, on x86 offsetof(vivi_dev, line) was 1003 and after
patch it is 1004.
There is slight performance increase, but I think is is slight, only
because we start copying not from line[0]:
    ---- 8< ---- drivers/media/platform/vivi.c
    static void vivi_fillbuff(struct vivi_dev *dev, struct vivi_buffer *buf)
    {
            ...
            for (h = 0; h < hmax; h++)
                    memcpy(vbuf + h * wmax * dev->pixelsize,
                           dev->line + (dev->mv_count % wmax) * dev->pixelsize,
                           wmax * dev->pixelsize);
before:
    # cmdline : /home/kirr/local/perf/bin/perf record -g -a sleep 20
    #
    # Samples: 49K of event 'cycles'
    # Event count (approx.): 16799780016
    #
    # Overhead          Command         Shared Object
    # ........  ...............  ....................
    #
        27.51%             rawv  libc-2.13.so          [.] __memcpy_ssse3
        23.77%           vivi-*  [kernel.kallsyms]     [k] memcpy
         9.96%             Xorg  [unknown]             [.] 0xa76f5e12
         4.94%           vivi-*  [vivi]                [k] gen_text.constprop.6
         4.44%             rawv  [vivi]                [k] gen_twopix
         3.17%           vivi-*  [vivi]                [k] vivi_fillbuff
         2.45%             rawv  [vivi]                [k] precalculate_line
         1.20%          swapper  [kernel.kallsyms]     [k] read_hpet
    23.77%           vivi-*  [kernel.kallsyms]     [k] memcpy
                     |
                     --- memcpy
                        |
                        |--99.28%-- vivi_fillbuff
                        |          vivi_thread
                        |          kthread
                        |          ret_from_kernel_thread
                         --0.72%-- [...]
after:
    # cmdline : /home/kirr/local/perf/bin/perf record -g -a sleep 20
    #
    # Samples: 49K of event 'cycles'
    # Event count (approx.): 16475832370
    #
    # Overhead          Command           Shared Object
    # ........  ...............  ......................
    #
        29.07%             rawv  libc-2.13.so            [.] __memcpy_ssse3
        20.57%           vivi-*  [kernel.kallsyms]       [k] memcpy
        10.20%             Xorg  [unknown]               [.] 0xa7301494
         5.16%           vivi-*  [vivi]                  [k] gen_text.constprop.6
         4.43%             rawv  [vivi]                  [k] gen_twopix
         4.36%           vivi-*  [vivi]                  [k] vivi_fillbuff
         2.42%             rawv  [vivi]                  [k] precalculate_line
         1.33%          swapper  [kernel.kallsyms]       [k] read_hpet

Signed-off-by: Kirill Smelkov <kirr@mns.spb.ru>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] vivi: Optimize gen_text()

I've noticed that vivi takes a lot of CPU to produce its frames.
For example for 8 devices and 8 simple programs running, where each
captures YUY2 640x480 and displays it to X via SDL, profile timing is as
follows:
    # cmdline : /home/kirr/local/perf/bin/perf record -g -a sleep 20
    # Samples: 82K of event 'cycles'
    # Event count (approx.): 31551930117
    #
    # Overhead          Command         Shared Object                                                           Symbol
    # ........  ...............  ....................
    #
        49.48%           vivi-*  [vivi]                [k] gen_twopix
        10.79%           vivi-*  [kernel.kallsyms]     [k] memcpy
        10.02%             rawv  libc-2.13.so          [.] __memcpy_ssse3
         8.35%           vivi-*  [vivi]                [k] gen_text.constprop.6
         5.06%             Xorg  [unknown]             [.] 0xa73015f8
         2.32%             rawv  [vivi]                [k] gen_twopix
         1.22%             rawv  [vivi]                [k] precalculate_line
         1.20%           vivi-*  [vivi]                [k] vivi_fillbuff
    (rawv is display program, vivi-* is a combination of vivi-000 through vivi-007)
so a lot of time is spent in gen_twopix() which as the follwing
call-graph profile shows ...
    49.48%           vivi-*  [vivi]                [k] gen_twopix
                     |
                     --- gen_twopix
                        |
                        |--96.30%-- gen_text.constprop.6
                        |          vivi_fillbuff
                        |          vivi_thread
                        |          kthread
                        |          ret_from_kernel_thread
                        |
                         --3.70%-- vivi_fillbuff
                                   vivi_thread
                                   kthread
                                   ret_from_kernel_thread
... is called mostly from gen_text().
If we'll look at gen_text(), in the inner loop, we'll see
    if (chr & (1 << (7 - i)))
            gen_twopix(dev, pos + j * dev->pixelsize, WHITE, (x+y) & 1);
    else
            gen_twopix(dev, pos + j * dev->pixelsize, TEXT_BLACK, (x+y) & 1);
which calls gen_twopix() for every character pixel, and that is very
expensive, because gen_twopix() branches several times.
Now, let's note, that we operate on only two colors - WHITE and
TEXT_BLACK, and that pixel for that colors could be precomputed and
gen_twopix() moved out of the inner loop. Also note, that for black
and white colors even/odd does not make a difference for all supported
pixel formats, so we could stop doing that `odd` gen_twopix() parameter
game.
So the first thing we are doing here is
    1) moving gen_twopix() calls out of gen_text() into vivi_fillbuff(),
       to pregenerate black and white colors, just before printing
       starts.
what we have next is that gen_text's font rendering loop, even with
gen_twopix() calls moved out, was inefficient and branchy, so let's
    2) rewrite gen_text() loop so it uses less variables + unroll char
       horizontal-rendering loop + instantiate 3 code paths for pixelsizes 2,3
       and 4 so that in all inner loops we don't have to branch or make
       indirections (*).
Done all above reworks, for gen_text() we get nice, non-branchy
streamlined code (showing loop for pixelsize=2):
           ?       cmp    $0x2,%eax
           ?     ? jne    26
           ?       mov    -0x18(%ebp),%eax
           ?       mov    -0x20(%ebp),%edi
           ?       imul   -0x20(%ebp),%eax
           ?       movzwl 0x3ffc(%ebx),%esi
      0,08 ?       movzwl 0x4000(%ebx),%ecx
      0,04 ?       add    %edi,%edi
           ?       mov    0x0,%ebx
      0,51 ?       mov    %edi,-0x1c(%ebp)
           ?       mov    %ebx,-0x14(%ebp)
           ?       movl   $0x0,-0x10(%ebp)
           ?       lea    0x20(%edx,%eax,2),%eax
           ?       mov    %eax,-0x18(%ebp)
           ?       xchg   %ax,%ax
      0,04 ? a0:   mov    0x8(%ebp),%ebx
           ?       mov    -0x18(%ebp),%eax
      0,04 ?       movzbl (%ebx),%edx
      0,16 ?       test   %dl,%dl
      0,04 ?     ? je     128
      0,08 ?       lea    0x0(%esi),%esi
      1,61 ? b0:???shl    $0x4,%edx
      1,02 ?    ?  mov    -0x14(%ebp),%edi
      2,04 ?    ?  add    -0x10(%ebp),%edx
      2,24 ?    ?  lea    0x1(%ebx),%ebx
      0,27 ?    ?  movzbl (%edi,%edx,1),%edx
      9,92 ?    ?  mov    %esi,%edi
      0,39 ?    ?  test   %dl,%dl
      2,04 ?    ?  cmovns %ecx,%edi
      4,63 ?    ?  test   $0x40,%dl
      0,55 ?    ?  mov    %di,(%eax)
      3,76 ?    ?  mov    %esi,%edi
      0,71 ?    ?  cmove  %ecx,%edi
      3,41 ?    ?  test   $0x20,%dl
      0,75 ?    ?  mov    %di,0x2(%eax)
      2,43 ?    ?  mov    %esi,%edi
      0,59 ?    ?  cmove  %ecx,%edi
      4,59 ?    ?  test   $0x10,%dl
      0,67 ?    ?  mov    %di,0x4(%eax)
      2,55 ?    ?  mov    %esi,%edi
      0,78 ?    ?  cmove  %ecx,%edi
      4,31 ?    ?  test   $0x8,%dl
      0,67 ?    ?  mov    %di,0x6(%eax)
      5,76 ?    ?  mov    %esi,%edi
      1,80 ?    ?  cmove  %ecx,%edi
      4,20 ?    ?  test   $0x4,%dl
      0,86 ?    ?  mov    %di,0x8(%eax)
      2,98 ?    ?  mov    %esi,%edi
      1,37 ?    ?  cmove  %ecx,%edi
      4,67 ?    ?  test   $0x2,%dl
      0,20 ?    ?  mov    %di,0xa(%eax)
      2,78 ?    ?  mov    %esi,%edi
      0,75 ?    ?  cmove  %ecx,%edi
      3,92 ?    ?  and    $0x1,%edx
      0,75 ?    ?  mov    %esi,%edx
      2,59 ?    ?  mov    %di,0xc(%eax)
      0,59 ?    ?  cmove  %ecx,%edx
      3,10 ?    ?  mov    %dx,0xe(%eax)
      2,39 ?    ?  add    $0x10,%eax
      0,51 ?    ?  movzbl (%ebx),%edx
      2,86 ?    ?  test   %dl,%dl
      2,31 ?    ???jne    b0
      0,04 ?128:   addl   $0x1,-0x10(%ebp)
      4,00 ?       mov    -0x1c(%ebp),%eax
      0,04 ?       add    %eax,-0x18(%ebp)
      0,08 ?       cmpl   $0x10,-0x10(%ebp)
           ?     ? jne    a0
which almost goes away from the profile:
    # cmdline : /home/kirr/local/perf/bin/perf record -g -a sleep 20
    # Samples: 49K of event 'cycles'
    # Event count (approx.): 16799780016
    #
    # Overhead          Command         Shared Object                                                           Symbol
    # ........  ...............  ....................
    #
        27.51%             rawv  libc-2.13.so          [.] __memcpy_ssse3
        23.77%           vivi-*  [kernel.kallsyms]     [k] memcpy
         9.96%             Xorg  [unknown]             [.] 0xa76f5e12
         4.94%           vivi-*  [vivi]                [k] gen_text.constprop.6
         4.44%             rawv  [vivi]                [k] gen_twopix
         3.17%           vivi-*  [vivi]                [k] vivi_fillbuff
         2.45%             rawv  [vivi]                [k] precalculate_line
         1.20%          swapper  [kernel.kallsyms]     [k] read_hpet
i.e. gen_twopix() overhead dropped from 49% to 4% and gen_text() loops
from ~8% to ~4%, and overal cycles count dropped from 31551930117 to
16799780016 which is ~1.9x whole workload speedup.
(*) for RGB24 rendering I've introduced x24, which could be thought as
    synthetic u24 for simplifying the code. That's done because for
    memcpy used for conditional assignment, gcc generates suboptimal code
    with more indirections.
    Fortunately, in C struct assignment is builtin and that's all we
    need from pixeltype for font rendering.

Signed-off-by: Kirill Smelkov <kirr@mns.spb.ru>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] staging/media: Use dev_ printks in cxd2099/cxd2099.[ch]

fixed below checkpatch warnings.
- WARNING: Prefer netdev_err(netdev, ... then dev_err(dev, ... then pr_err(...  to printk(KERN_ERR ...
- WARNING: Prefer netdev_info(netdev, ... then dev_info(dev, ... then pr_info(...  to printk(KERN_INFO ...
- WARNING: Prefer netdev_warn(netdev, ... then dev_warn(dev, ... then pr_warn(...  to printk(KERN_WARNING ...

Signed-off-by: YAMANE Toshiaki <yamanetoshi@gmail.com>
Tested-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] tda18212: tda18218: use 'val' if initialized

Commits e666a44fa313cb9329c0381ad02fc6ee1e21cb31 ("[media] tda18212:
silence compiler warning") and e0e52d4e9f5bce7ea887027c127473eb654a5a04
("[media] tda18218: silence compiler warning") silenced warnings
equivalent to these:
    drivers/media/tuners/tda18212.c: In function ‘tda18212_attach’:
    drivers/media/tuners/tda18212.c:299:2: warning: ‘val’ may be used uninitialized in this function [-Wmaybe-uninitialized]
    drivers/media/tuners/tda18218.c: In function ‘tda18218_attach’:
    drivers/media/tuners/tda18218.c:305:2: warning: ‘val’ may be used uninitialized in this function [-Wmaybe-uninitialized]
But in both cases 'val' will still be used uninitialized if the calls
of tda18212_rd_reg() or tda18218_rd_reg() fail. Fix this by only
printing the "chip id" if the calls of those functions were successful.
This allows to drop the uninitialized_var() stopgap measure.
Also stop printing the return values of tda18212_rd_reg() or
tda18218_rd_reg(), as these are not interesting.

Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] budget-av: only use t_state if initialized

Building budget-av.o triggers this GCC warning:
    In file included from drivers/media/pci/ttpci/budget-av.c:44:0:
    drivers/media/dvb-frontends/tda8261_cfg.h: In function ‘tda8261_get_bandwidth’:
    drivers/media/dvb-frontends/tda8261_cfg.h:68:21: warning: ‘t_state.bandwidth’ may be used uninitialized in this function [-Wuninitialized]
Move the printk() that uses t_state.bandwith to the location where it
should be initialized to fix this.

Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] staging: media: Fix minor typo in staging/media

Correct spelling typo in comment witin staging/media.

Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] media: ov7670: Allow 32x maximum gain for yuv422

4x gain ceiling is not enough to capture a decent image in conditions
of total darkness and only a LED light source. Allow a maximum gain
of 32x instead.
This doesn't have any drawback since the image quality in 'normal'
light conditions is the same.

Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] media: m2m-deinterlace: Do not set debugging flag to true

Default value should be 'debugging disabled'.

Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] drivers/media/pci/saa7134/saa7134-dvb.c: Test if videobuf_dvb_get_frontend return NULL

Based on commit: e66131cee501ee720b7b58a4b87073b8fbaaaba6
Not testing videobuf_dvb_get_frontend output may cause OOPS if it return
NULL. This patch fixes this issue.
The semantic patch that found this issue is(http://coccinelle.lip6.fr/):
// <smpl>
@@
identifier i,a,b;
statement S, S2;
@@
i = videobuf_dvb_get_frontend(...);
... when != if (!i) S
* if (i->a.b)
S2
// </smpl>

Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] media: coda: Fix H.264 header alignment - v2

Length of H.264 headers is variable and thus it might not be
aligned for the coda to append the encoded frame. This causes
the first frame to overwrite part of the H.264 PPS.
In order to solve that, a filler NAL must be added between
the headers and the first frame to preserve alignment.

[mchehab@redhat.com: applied only v2 diff here, as v1 ended by mistakenly
 being applied]
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] media: coda: Fix H.264 header alignment

Length of H.264 headers is variable and thus it might not be
aligned for the coda to append the encoded frame. This causes
the first frame to overwrite part of the H.264 PPS.
In order to solve that, a filler NAL must be added between
the headers and the first frame to preserve alignment.

[mchehab@redhat.com: Fix a few CodingStyle issues]
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] rc: Fix double free in gpio_ir_recv_remove()

Since rc_unregister_device() frees its argument there's no need to
subsequently call rc_free_device() on the same variable - in fact it's
a double free bug.
Easily fixed by just removing the rc_free_device() call.

Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] rc: Fix double free in gpio_ir_recv_probe()

At the 'err_request_irq' label, rc_unregister_device(rcdev) frees its
argument. So when we fall through to the 'err_gpio_request' label
further down and call rc_free_device(rcdev) then that's a double free.
Fix that by moving 'rcdev = NULL' from after the call to
rc_free_device() to after rc_unregister_device(). That fixes the
problem since rc_free_device() just does nothing if passed NULL and
there's no further use of 'rcdev' after the call to rc_free_device()
so it's not needed there.

Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] tda10071: fix a warning introduced by changeset 41f55d5755

The two new tests don't set the returned value.

Cc: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] tda10071: make sure both tuner and demod i2c addresses are specified

display an error message if either tuner_i2c_addr or demod_i2c_addr
are not specified in the tda10071_config structure

Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] or51211: apply pr_fmt and use pr_* macros instead of printk

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] ix2505v: use %*ph[N] to dump small buffers

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] or51211: use %*ph[N] to dump small buffers

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] davinci: vpbe: remove unused variable in vpbe_initialize()

The variable 'output_index' is initialized but never used
otherwise, so remove the unused variable.

Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Prabhakar Lad <prabhakar.lad@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] media: davinci: vpbe: return error code on error in vpbe_display_g_crop()

We have assigned error code to 'ret' if crop->type is not
V4L2_BUF_TYPE_VIDEO_OUTPUT, but never use it.
We'd better return the error code on this error.

Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Prabhakar Lad <prabhakar.lad@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] media: davinci: vpbe: fix return value check in vpbe_display_reqbufs()

In case of error, the function vb2_dma_contig_init_ctx() returns
ERR_PTR() and never returns NULL. The NULL test in the return value
check should be replaced with IS_ERR().

Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Prabhakar Lad <prabhakar.lad@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] media: davinci: vpbe: enable building of vpbe driver for DM355 and DM365

This patch allows enabling building of VPBE display driver for DM365
and DM355. This also removes unnecessary entry VIDEO_DM644X_VPBE
in Kconfig, which could have been done with single entry, and
appropriate changes in Makefile for building.

Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] davinci: vpbe: pass different platform names to handle different ip's

The vpbe driver can handle different platforms DM644X, DM36X and
DM355. To differentiate between this platforms venc_type/vpbe_type
was passed as part of platform data which was incorrect. The correct
way to differentiate to handle this case is by passing different
platform names.
This patch creates platform_device_id[] array supporting different
platforms and assigns id_table to the platform driver, and finally
in the probe gets the actual device by using platform_get_device_id()
and gets the appropriate driver data for that platform.
Taking this approach will also make the DT transition easier.

Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] davinci: vpfe: Add documentation and TODO

Add documentation on the Davinci VPFE driver. Document the subdevs,
and private IOTCLs the driver implements. This patch also includes
the TODO's to fit into drivers/media/ folder.

Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] davinci: vpfe: dm365: add build infrastructure for capture driver

add build infrastructure for dm365 specific modules for VPFE
capture driver.

Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] davinci: vpfe: dm365: resizer driver based on media framework

Add the video resizer driver with the v4l2 media controller framework
which takes care of resizing the video frames with both up-scaling
downscaling facility. The driver supports both continuous and
single shot operations.The driver supports resizer as a subdevice
and a media entity. It has support for 2 resizers - resizerA
and resizerB.

Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] davinci: vpfe: dm365: add IPIPE hardware layer support

IPIPE is the hardware IP which implements the functionality
required for resizer, ipipe(colorspace converter) and
the associated hardware support. This patch implements hardware
setup including coefficient programming for various hardware
filters, gamma, cfa and clock enabling.

Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] davinci: vpfe: dm365: add IPIPE support for media controller driver

Add the IPIPE subdevice to the DM365 vpfe driver. The IPIPE is the
major sub IP in the DM365 capture VPFE hardware and implements
black clamping, color space conversion, edge enhancements etc.
the block is exposed as a subdevice and implements media controller
based setup and a private IOCTL for fine grain control.

Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] davinci: vpfe: dm365: add ISIF driver based on media framework

add support for ISIF as a subdevice for dm365 vpfe capture driver.
ISIF is responsible for capturing video data both in raw bayer format
on sync seperate signals and YUV through BT656/1120 interfaces.
ISIF is exposed as a subdev for the vpfe driver and allows users to
use the driver through standard media controller interface.

Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] davinci: vpfe: dm365: add IPIPEIF driver based on media framework

add support for dm365 IPIPEIF driver based on media framework.
The IPIPEIF is exposed as a subdev, and it supports features
like fault pixel correction, dark frame subtraction and other
necessary hardware setup.

Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] davinci: vpfe: add v4l2 video driver support

Add a generic video driver functionality to be used by all the vpfe
drivers for davinci SoCs. The functionality includes all the
standard v4l2 interfaces including streaming. The video node
interface can be used both as an input and output node for both
continuous and single shot modes. Also supports dv_presets to include
HD modes, wth support for both user pointer IO and mmap. The buffering
mechanism is based on videobuf2 interface.

Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] davinci: vpfe: add v4l2 capture driver with media interface

Add the vpfe capture driver which implements media controller
interface. The driver supports the DM365 sub ip units for capture
namely - ISIF, IPIPE, IPIPEIF, Resizer. This file represents the main
driver which does isr registration, v4l2 device registration,
media registration and platform driver registrations.
It calls the appropriate subdevs from here to create subdevices
and media entities.

Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] davinci/vpss: add helper functions for setting hw params

Add vpss helper functions to be used in the main driver for setting
hardware parameters.

Add interface functions to set sync polarity, interrupt completion and
pageframe size in vpss to be used by the main driver.

Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] davinci: vpss: dm365: set vpss clk ctrl

request_mem_region for VPSS_CLK_CTRL register and ioremap.
and enable clocks appropriately.

Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] davinci: vpss: dm365: enable ISP registers

enable the clocks required for VPFE to work in PCCR register,
and enbale ISIF out on BCR to get the correct operation from ISIF.

Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] s5p-fimc: Improved pipeline try format routine

Make the pipeline try format routine more generic to support any
number of subdevs in the pipeline, rather than hard coding it for
only a sensor, MIPI-CSIS and FIMC subdevs and the FIMC video node.

Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] gspca_sonixj: Add a small delay after i2c_w1

We already have the same delay in i2c_w8, but it was missing from i2c_w1,
adding this delay fixes the Microsoft VX-3000 camera often (but not always)
streaming video data with a very green-ish tint.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] gspca_sonixb: Properly wait between i2c writes

We must wait for the previous i2c write to complete before starting a new
one. Sofar we were getting away with this, but it seems that some parts
of the usb-subsystem has been sped up making us go to fast :)
This fixes streaming on sn9c103 based cams not working with an
"i2c_w error" error.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] gspca_t613: Fix compiling with GSPCA_DEBUG defined

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] gspca_stv06xx: Disable flip controls for vv6410 sensor

Disable the hardware VFLIP and HFLIP controls for now as we lack a
mechanism to adjust the frame offset, thus rending a bayerimage not
compliant with the announced format.

Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] gspca: Use module_usb_driver macro

module_usb_driver eliminates a lot of boilerplate by replacing
module_init() and module_exit() calls.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] gspca_kinect: add Kinect for Windows USB id

Add the USB ID for the Kinect for Windows RGB camera so it can be used
with the gspca_kinect driver.

Signed-off-by: Jacob Schloss <jacob.schloss@unlimitedautomata.com>
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] Documentation/media: Remove docs for obsoleted and removed v4l1 drivers

When the v4l1 drivers were removed, there docs were forgotten.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] stk-webcam: Add an upside down dmi table, and add the Asus G1 to it

The stk-webcam module is inserted upside-down in some webcams, so we
need to de hflip and vflip by default on some models.
Note that this patch inverts the value of the controls as reported by
the control API in this case so that for the user they still make sense
(iow not doing any flipping from the ctrl API pov results in an upright
image).

Reported-by: Jose Gómez <adler@dreamcoder.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] gspca-pac207: Add a led_invert module parameter

Some cams have their led connected in such a way that on = off and visa versa
unfortunately we cannot tell this from the driver in any way, so add a module
parameter for this.

Reported-by: Yuri Glushkov <yglushkov@yahoo.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] gspca - stv06xx: Fix a regression with the bridge/sensor vv6410

Setting the H and V flip controls at webcam connection time prevents
the webcam to work correctly.
This patch checks if the webcam is streaming before setting the flips.
It does not set the flips (nor other controls) at webcam start time.

Tested-by: Philippe ROUBACH <philippe.roubach@free.fr>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] s5p-fimc: Add support for sensors with multiple pads

Some sensors can have more than one pad (case of S5C73M3).
In such cases FIMC assumes the last pad of the sensor is
the source pad.

Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] fimc-lite: Add ISP FIFO output support

Add second source media pad for the FIFO data output to FIMC-IS
and implement subdev s_stream op for configurations where FIMC-LITE
is used as a glue logic between FIMC-IS and MIPI-CSIS or an image
sensor. The second source media pad will be linked to the FIMC-LITE
video node.
For proper configuration the attached image sensor/video encoder
properties are needed, like video bus type, signal polarities, etc.
For this purpose there is a small routine added that walks the
pipeline and returns the sensor subdev.

Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] s5p-fimc: Add sensor group ids for fimc-is

Add subdev group id definition for FIMC-IS ISP and sensor subdev.
While at it rename all group id definitions to start with GRP_ID.

Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] s5p-csis: Add registers logging for debugging

Dump registers contents together with the event counters state
in VIDIOC_LOG_STATUS ioctl.

Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] s5p-csis: Enable only data lanes that are actively used

Enable only MIPI CSI-2 data lanes at the DPHY that are actively
used, rather than unmasking all unconditionally.

Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] s5p-csis: Add support for raw Bayer pixel formats

The MIPI CSIS device supports MIPI CSI-2 RAW8, RAW10, RAW12 data
types. Add related media bus pixel format definitions. This
doesn't cover all possible supported media bus pixel formats.

Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] s5p-fimc: Add variant data structure for Exynos4x12

Add variant data structures for Exynos4212 and Exynos4412 SoC.
Add 'const' qualifier for the variant description structures.
Also remove has_cam_if flags from FIMC3 on Exynos4210 SoC is
it has no interconnections the camera ports.

Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] s5p-fimc: Clean up capture enable/disable helpers

The FIMC FIFO output is not supported in the driver due to
some hardware issues thus we can remove some code as out_path
is always FIMC_IO_DMA.

Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] fimc-lite: Register dump function cleanup

Use v4l2_info() to make it possible to identify which FIMC-LITE
device instance the logs refer to.

Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] V4L: DocBook: Add V4L2_MBUS_FMT_YUV10_1X30 media bus pixel code

This patch adds definition of media bus code for YUV pixel format
transferred in 30-bit samples where each component has 10 bits width.

[mchehab@redhat.com: fix a merge conflict at v4l2-mediabus.h]
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] s5p-csis: Correct the event counters logging

The counter field is unsigned so >= 0 condition always evaluates
to true. Fix this to log events for which counter is > 0 or for
all when in debug mode.

Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] s5p-fimc: Fix horizontal/vertical image flip

Setting FIMC_REG_CITRGFMT_FLIP_X_MIRROR bit causes X-axis image
flip (vertical flip) and thus it corresponds to V4L2_CID_VFLIP.
Likewise, setting FIMC_REG_CITRGFMT_FLIP_Y_MIRROR bit causes Y-axis
image flip (horizontal flip) and thus it corresponds to V4L2_CID_HFLIP.
Currently the driver does X-axis flip when V4L2_CID_HFLIP is set and
Y-axis flip for V4L2_CID_VFLIP. Fix this incorrect assignment by setting
proper FIMC_REG_CITRGFMT register bits for ctx->hflip and ctx->vflip.

Reported-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] v4l: There's no __unsigned

Correct a typo. v4l2_plane.m.userptr is unsigned long, not __unsigned long.

Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] v4l: Tell user space we're using monotonic timestamps

Set buffer timestamp flags for videobuf, videobuf2 and drivers that use
neither.

Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] v4l: Convert drivers to use monotonic timestamps

Convert drivers using wall clock time (CLOCK_REALTIME) to timestamp from the
monotonic timer (CLOCK_MONOTONIC).

Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] v4l: Helper function for obtaining timestamps

v4l2_get_timestamp() produces a monotonic timestamp but unlike
ktime_get_ts(), it uses struct timeval instead of struct timespec, saving
the drivers the conversion job when getting timestamps for v4l2_buffer's
timestamp field.

Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] v4l: Define video buffer flags for timestamp types

Define video buffer flags for different timestamp types. Everything up to
now have used either realtime clock or monotonic clock, without a way to
tell which clock the timestamp was taken from.
Also document that the clock source of the timestamp in the timestamp field
depends on buffer flags.

[mchehab@redhat.com: fix a few wrong references to Kernel 3.8 - as this patch
 is meant for 3.9]
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] exynos-gsc: modify number of output/capture buffers

G-Scaler src buffer count as well as destination buffer
count is increased to 32. This is required for G-Scaler to
interface with MFC, as MFC demands 32 capture buffers for
some H264 streams.

Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] exynos-gsc: Use devm_clk_get()

devm_clk_get() is a device managed function and makes error handling
a bit simpler.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] exynos-gsc: Correct the clock handling

Make sure there is no unbalanced clk_unprepare call and add missing
clock release in the driver's remove() callback.

Signed-off-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] exynos-gsc: Rearrange error messages for valid prints

In case of clk_prepare failure, the function gsc_clk_get also prints
"failed to get clock" which is not correct. Hence move the error
messages to their respective blocks. While at it, also renamed the labels
meaningfully.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] exynos-gsc: Fix checkpatch warning in gsc-m2m.c

Fixes the following warning:
WARNING: space prohibited between function name and open parenthesis '('
FILE: media/platform/exynos-gsc/gsc-m2m.c:606:
ctx = kzalloc(sizeof (*ctx), GFP_KERNEL);

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] exynos-gsc: propagate timestamps from src to dst buffers

Make gsc-m2m propagate the timestamp field from source to destination
buffers.

Signed-off-by: John Sheu <sheu@google.com>
Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] exynos-gsc: Adding tiled multi-planar format to G-Scaler

Adding V4L2_PIX_FMT_NV12MT_16X16 to G-Scaler supported formats.
If the output or input format is V4L2_PIX_FMT_NV12MT_16X16, configure
G-Scaler to use GSC_IN_TILE_MODE.

[s.nawrocki: shortened the pixel format description]

Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] ivtv: ivtv-driver: Replace 'flush_work_sync()'

Since commit 43829731d (workqueue: deprecate flush[_delayed]_work_sync()),
flush_work() should be used instead of flush_work_sync().

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] tm6000-video.c: warning fix

drivers/media/usb/tm6000/tm6000-video.c: In function '__check_keep_urb':
drivers/media/usb/tm6000/tm6000-video.c:1926:1: warning: return from incompatible pointer type [enabled by default]

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] sh_veu.c: fix two compilation warnings

drivers/media/platform/sh_veu.c:269:2: warning: format '%x' expects argument of type 'unsigned int', but argument 5 has type 'dma_addr_t' [-Wformat]
drivers/media/platform/sh_veu.c:276:2: warning: format '%x' expects argument of type 'unsigned int', but argument 5 has type 'dma_addr_t' [-Wformat]

Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] media: mx2_camera: Add image size HW limits

The CSI on i.MX27 has some constraints regarding image width.
This patch makes sure those requirements are met in try_fmt().

Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
[g.liakhovetski@gmx.de: make constraint i.MX27-specific]
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] MAINTAINERS: add entries for sh_veu and sh_vou V4L2 drivers

sh_vou might be better described by "Odd Fixes," but mark it "Maintained"
for now. sh_veu is a new driver and might see some development in the
future.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] sh_mobile_ceu_camera: use managed memory and resource allocations

Use managed allocations to simplify error handling and clean up paths.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] media: sh_mobile_csi2: use managed memory and resource allocations

Use managed allocations to simplify error handling and clean up paths.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] media: soc-camera: remove superfluous JPEG checking

Explicit checks for the JPEG pixel format in soc_mbus_bytes_per_line() and
soc_mbus_image_size() are superfluous, because also without them these
functions will perform correctly. The former will return 0 based on
packing == SOC_MBUS_PACKING_VARIABLE and the latter will simply multiply
the user-provided line length by the image height to obtain a frame buffer
size estimate. The original version of the "media: soc_camera: don't clear
pix->sizeimage in JPEG mode" patch was correct and my amendment, adding
these two checks was superfluous.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] media: soc-camera: update documentation

Update soc-camera documentation to reflect the current camera host API and
the use of the common V4L2 subdev API.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] media: sh-mobile-ceu-camera: runtime PM suspending doesn't have to be synchronous

In both error and clean up cases there is no need to wait for runtime PM
to finish suspending the device.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] media: soc-camera: use managed devm_regulator_bulk_get()

Using device-managed devm_regulator_bulk_get() eliminates the need to
release regulators explicitly.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] media: add a VEU MEM2MEM format conversion and scaling driver

Video Engine Unit (VEU) is an IP block, found in multiple SuperH and ARM-
based sh-mobile and r-mobile SoCs, capable of processing video data. It
can perform colour-space conversion, scaling and several filtering
transformations. This patch adds an initial implementation of a mem2mem
V4L2 driver for VEU. So far only conversion from NV12 to RGB565 is
supported. Further functionality shall be added in the future.
This driver is based on a VEU vidix driver by Magnus Damm.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] media: mem2mem: make reference to struct m2m_ops in the core const

The mem2mem core doesn't change struct m2m_ops, provided by the driver,
make references to it const.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] omap_vout: Use the output overlay ioctl operations

The omap_vout device implements the output overlay API, use the
corresponding ioctl operations.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] omap_vout: Drop overlay format enumeration

Enumerating formats for output overlays doesn't make sense, as the pixel
format is defined by the display API, not the V4L2 API. Drop the
vidioc_enum_fmt_vid_overlay ioctl operation.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] v4l2: add new pixel formats supported on dm365

add new macro V4L2_PIX_FMT_SGRBG10ALAW8 and associated formats
to represent Bayer format frames compressed by A-LAW algorithm,
add V4L2_PIX_FMT_UV8 to represent storage of CbCr data (UV interleaved)
only.

Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] DocBook: fix an index reference

Error: no ID for constraint linkend: V4L2-PIX-FMT-NV12MT-16X16.

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] media: add new mediabus format enums for dm365

add new enum entries for supporting the media-bus formats on dm365.
These include some bayer and some non-bayer formats.
V4L2_MBUS_FMT_YDYUYDYV8_1X16 and V4L2_MBUS_FMT_UV8_1X8 are used
internal to the hardware by the resizer.
V4L2_MBUS_FMT_SBGGR10_ALAW8_1X8 represents the bayer ALAW format
that is supported by dm365 hardware.

Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] Documentation: fix outdated statement re. v4l2

Fix tense used for describing struct v4l2_fh as it has been added a
while ago.

Signed-off-by: Nicolas Thery <nicolas.thery@st.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] MAINTAINERS: fix drivers/media/usb/dvb-usb/cxusb*

This driver was never at dvb-usb-v2, as far as I could see.

Signed-off-by: Cesar Eduardo Barros <cesarb@cesarb.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] MAINTAINERS: fix drivers/media/platform/atmel-isi.c

This file was moved to drivers/media/platform/soc_camera/atmel-isi.c by
commit b47ff4a ([media] move soc_camera to its own directory).

Cc: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Cesar Eduardo Barros <cesarb@cesarb.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] MAINTAINERS: add entry for dsbr100 usb radio driver

This patch adds MAINTAINERS entry for dsbr100 usb radio driver.

Signed-off-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] MAINTAINERS: add g2d entry

Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] MAINTAINERS: add entry for radio-ma901 driver

This patch adds MAINTAINERS entry for radio-ma901 usb radio driver.

Signed-off-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] tda18271: add missing entries for qam_7 to tda18271_update_std_map() and tda18271_dump_std_map()

Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] cx23885: add basic DVB-S2 support for Hauppauge HVR-4400

Add basic DVB-S2 support for the Hauppauge HVR-4400 PCIe board.
Thanks to Antti Palosaari and Devin Heitmueller for their
suggestions and testing.

Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Reviewed-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] tda10071: add tuner_i2c_addr to struct tda10071_config

The default i2c address for the tuner is 0x14,
allow this to be overridden with a configuration parameter

Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] au0828: break au0828_card_setup() down into smaller functions

Pull the analog frontend setup code out of au0828_card_setup into its
own seperate function, au0828_card_analog_fe_setup().

Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] au0828: remove forced dependency of VIDEO_AU0828 on VIDEO_V4L2

This patch removes the dependendency of VIDEO_AU0828 on VIDEO_V4L2 by
creating a new Kconfig option, VIDEO_AU0828_V4L2, which enables analog
video capture support and depends on VIDEO_V4L2 itself.
With VIDEO_AU0828_V4L2 disabled, the driver will only support digital
television and will not depend on the v4l2-core. With VIDEO_AU0828_V4L2
enabled, the driver will be built with the analog v4l2 support included.
By default, the VIDEO_AU0828_V4L2 option will be set to Y, so as to
preserve the original behavior.

Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] au0828: update model matrix entries for 72261, 72271 & 72281

Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>