tty: 8250: Add support for Brainboxes PX cards.

[ Upstream commit ef5a03a26c87a760bc3d86b5af7b773e82f8b1b7 ]

Add support for some of the Brainboxes PCIe (PX) range of
serial cards, including the PX-101, PX-235/PX-246,
PX-203/PX-257, PX-260/PX-701, PX-310, PX-313,
PX-320/PX-324/PX-376/PX-387, PX-335/PX-346, PX-368, PX-420,
PX-803 and PX-846.

Signed-off-by: Cameron Williams <cang1@live.co.uk>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/AM5PR0202MB2564669252BDC59BF55A6E87C4879@AM5PR0202MB2564.eurprd02.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

serial: 8250: Add proper clock handling for OxSemi PCIe devices

[ Upstream commit 366f6c955d4d1a5125ffcd6875ead26a3c7a2a1c ]

Oxford Semiconductor PCIe (Tornado) 950 serial port devices are driven
by a fixed 62.5MHz clock input derived from the 100MHz PCI Express clock.

We currently drive the device using its default oversampling rate of 16
and the clock prescaler disabled, consequently yielding the baud base of
3906250.  This base is inadequate for some of the high-speed baud rates
such as 460800bps, for which the closest rate possible can be obtained
by dividing the baud base by 8, yielding the baud rate of 488281.25bps,
which is off by 5.9638%.  This is enough for data communication to break
with the remote end talking actual 460800bps, where missed stop bits
have been observed.

We can do better however, by taking advantage of a reduced oversampling
rate, which can be set to any integer value from 4 to 16 inclusive by
programming the TCR register, and by using the clock prescaler, which
can be set to any value from 1 to 63.875 in increments of 0.125 in the
CPR/CPR2 register pair.  The prescaler has to be explicitly enabled
though by setting bit 7 in the MCR or otherwise it is bypassed (in the
enhanced mode that we enable) as if the value of 1 was used.

Make use of these features then as follows:

- Set the baud base to 15625000, reflecting the minimum oversampling
  rate of 4 with the clock prescaler and divisor both set to 1.

- Override the `set_mctrl' and set the MCR shadow there so as to have
  MCR[7] always set and have the 8250 core propagate these settings.

- Override the `get_divisor' handler and determine a good combination of
  parameters by using a lookup table with predetermined value pairs of
  the oversampling rate and the clock prescaler and finding a pair that
  divides the input clock such that the quotient, when rounded to the
  nearest integer, deviates the least from the exact result.  Calculate
  the clock divisor accordingly.

  Scale the resulting oversampling rate (only by powers of two) if
  possible so as to maximise it, reducing the divisor accordingly, and
  avoid a divisor overflow for very low baud rates by scaling the
  oversampling rate and/or the prescaler even if that causes some
  accuracy loss.

  Also handle the historic spd_cust feature so as to allow one to set
  all the three parameters manually to arbitrary values, by keeping the
  low 16 bits for the divisor and then putting TCR in bits 19:16 and
  CPR/CPR2 in bits 28:20, sanitising the bit pattern supplied such as
  to clamp CPR/CPR2 values between 0.000 and 0.875 inclusive to 33.875.
  This preserves compatibility with any existing setups, that is where
  requesting a custom divisor that only has any bits set among the low
  16 the oversampling rate of 16 and the clock prescaler of 33.875 will
  be used as with the original 8250.

  Finally abuse the `frac' argument to store the determined bit patterns
  for the TCR, CPR and CPR2 registers.

- Override the `set_divisor' handler so as to set the TCR, CPR and CPR2
  registers from the `frac' value supplied.  Set the divisor as usual.

With the baud base set to 15625000 and the unsigned 16-bit UART_DIV_MAX
limitation imposed by `serial8250_get_baud_rate' standard baud rates
below 300bps become unavailable in the regular way, e.g. the rate of
200bps requires the baud base to be divided by 78125 and that is beyond
the unsigned 16-bit range.  The historic spd_cust feature can still be
used to obtain such rates if so required.

See Documentation/tty/device_drivers/oxsemi-tornado.rst for more details.

Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2204181519450.9383@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

serial: 8250: Fold EndRun device support into OxSemi Tornado code

[ Upstream commit 1f32c65bad24b9787d3e52843de375430e3df822 ]

The EndRun PTP/1588 dual serial port device is based on the Oxford
Semiconductor OXPCIe952 UART device with the PCI vendor:device ID set
for EndRun Technologies and uses the same sequence to determine the
number of ports available.  Despite that we have duplicate code
specific to the EndRun device.

Remove redundant code then and factor out OxSemi Tornado device
detection.

Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2204181516220.9383@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

serial: 8250_pci: Replace dev_*() by pci_*() macros

[ Upstream commit 1177384179416c7136e1348f07609e0da1ae6b91 ]

PCI subsystem provides convenient shortcut macros for message printing.
Use those macros instead of dev_*().

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jiri Slaby <jslaby@kernel.org>
Link: https://lore.kernel.org/r/20211022135147.70965-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

serial: 8250_pci: Refactor the loop in pci_ite887x_init()

[ Upstream commit 35b4f17231923e2f64521bdf7a2793ce2c3c74a6 ]

The loop can be refactored by using ARRAY_SIZE() instead of NULL terminator.
This reduces code base and makes it easier to read and understand.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jiri Slaby <jslaby@kernel.org>
Link: https://lore.kernel.org/r/20211022135147.70965-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

PCI: qcom: Power on PHY before IPQ8074 DBI register accesses

[ Upstream commit a0e43bb9973b06ce5c666f0901e104e2037c1b34 ]

Currently the Gen2 port in IPQ8074 will cause the system to hang as it
accesses DBI registers in qcom_pcie_init_2_3_3(), and those are only
accesible after phy_power_on().

Move the DBI read/writes to a new qcom_pcie_post_init_2_3_3(), which is
executed after phy_power_on().

Link: https://lore.kernel.org/r/20220623155004.688090-1-robimarko@gmail.com
Fixes: a0fd361db8e5 ("PCI: dwc: Move "dbi", "dbi2", and "addr_space" resource setup into common code")
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Cc: stable@vger.kernel.org # v5.11+
Signed-off-by: Sasha Levin <sashal@kernel.org>

PCI/AER: Iterate over error counters instead of error strings

[ Upstream commit 5e6ae050955b566484f3cc6a66e3925eae87a0ed ]

Previously we iterated over AER stat *names*, e.g.,
aer_correctable_error_string[32], but the actual stat *counters* may not be
that large, e.g., pdev->aer_stats->dev_cor_errs[16], which means that we
printed junk in the sysfs stats files.

Iterate over the stat counter arrays instead of the names to avoid this
junk.

Also, added a build time check to make sure all
counters have entries in strings array.

Fixes: 0678e3109a3c ("PCI/AER: Simplify __aer_print_error()")
Link: https://lore.kernel.org/r/20220509181441.31884-1-mkhalfella@purestorage.com
Reported-by: Meeta Saggi <msaggi@purestorage.com>
Signed-off-by: Mohamed Khalfella <mkhalfella@purestorage.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Meeta Saggi <msaggi@purestorage.com>
Reviewed-by: Eric Badger <ebadger@purestorage.com>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>

iommu/vt-d: avoid invalid memory access via node_online(NUMA_NO_NODE)

[ Upstream commit b0b0b77ea611e3088e9523e60860f4f41b62b235 ]

KASAN reports:

[ 4.668325][ T0] BUG: KASAN: wild-memory-access in dmar_parse_one_rhsa (arch/x86/include/asm/bitops.h:214 arch/x86/include/asm/bitops.h:226 include/asm-generic/bitops/instrumented-non-atomic.h:142 include/linux/nodemask.h:415 drivers/iommu/intel/dmar.c:497)
[    4.676149][    T0] Read of size 8 at addr 1fffffff85115558 by task swapper/0/0
[    4.683454][    T0]
[    4.685638][    T0] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.19.0-rc3-00004-g0e862838f290 #1
[    4.694331][    T0] Hardware name: Supermicro SYS-5018D-FN4T/X10SDV-8C-TLN4F, BIOS 1.1 03/02/2016
[    4.703196][    T0] Call Trace:
[    4.706334][    T0]  <TASK>
[ 4.709133][ T0] ? dmar_parse_one_rhsa (arch/x86/include/asm/bitops.h:214 arch/x86/include/asm/bitops.h:226 include/asm-generic/bitops/instrumented-non-atomic.h:142 include/linux/nodemask.h:415 drivers/iommu/intel/dmar.c:497)

after converting the type of the first argument (@nr, bit number)
of arch_test_bit() from `long` to `unsigned long`[0].

Under certain conditions (for example, when ACPI NUMA is disabled
via command line), pxm_to_node() can return %NUMA_NO_NODE (-1).
It is valid 'magic' number of NUMA node, but not valid bit number
to use in bitops.
node_online() eventually descends to test_bit() without checking
for the input, assuming it's on caller side (which might be good
for perf-critical tasks). There, -1 becomes %ULONG_MAX which leads
to an insane array index when calculating bit position in memory.

For now, add an explicit check for @node being not %NUMA_NO_NODE
before calling test_bit(). The actual logics didn't change here
at all.

[0] https://github.com/norov/linux/commit/0e862838f290147ea9c16db852d8d494b552d38d

Fixes: ee34b32d8c29 ("dmar: support for parsing Remapping Hardware Static Affinity structure")
Cc: stable@vger.kernel.org # 2.6.33+
Reported-by: kernel test robot <oliver.sang@intel.com>
Signed-off-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Yury Norov <yury.norov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

KVM: x86: Signal #GP, not -EPERM, on bad WRMSR(MCi_CTL/STATUS)

[ Upstream commit 2368048bf5c2ec4b604ac3431564071e89a0bc71 ]

Return '1', not '-1', when handling an illegal WRMSR to a MCi_CTL or
MCi_STATUS MSR.  The behavior of "all zeros' or "all ones" for CTL MSRs
is architectural, as is the "only zeros" behavior for STATUS MSRs.  I.e.
the intent is to inject a #GP, not exit to userspace due to an unhandled
emulation case.  Returning '-1' gets interpreted as -EPERM up the stack
and effecitvely kills the guest.

Fixes: 890ca9aefa78 ("KVM: Add MCE support")
Fixes: 9ffd986c6e4e ("KVM: X86: #GP when guest attempts to write MCi_STATUS register w/o 0")
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
Link: https://lore.kernel.org/r/20220512222716.4112548-2-seanjc@google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

KVM: set_msr_mce: Permit guests to ignore single-bit ECC errors

[ Upstream commit 0471a7bd1bca2a47a5f378f2222c5cf39ce94152 ]

Certain guest operating systems (e.g., UNIXWARE) clear bit 0 of
MC1_CTL to ignore single-bit ECC data errors.  Single-bit ECC data
errors are always correctable and thus are safe to ignore because they
are informational in nature rather than signaling a loss of data
integrity.

Prior to this patch, these guests would crash upon writing MC1_CTL,
with resultant error messages like the following:

error: kvm run failed Operation not permitted
EAX=fffffffe EBX=fffffffe ECX=00000404 EDX=ffffffff
ESI=ffffffff EDI=00000001 EBP=fffdaba4 ESP=fffdab20
EIP=c01333a5 EFL=00000246 [---Z-P-] CPL=0 II=0 A20=1 SMM=0 HLT=0
ES =0108 00000000 ffffffff 00c09300 DPL=0 DS   [-WA]
CS =0100 00000000 ffffffff 00c09b00 DPL=0 CS32 [-RA]
SS =0108 00000000 ffffffff 00c09300 DPL=0 DS   [-WA]
DS =0108 00000000 ffffffff 00c09300 DPL=0 DS   [-WA]
FS =0000 00000000 ffffffff 00c00000
GS =0000 00000000 ffffffff 00c00000
LDT=0118 c1026390 00000047 00008200 DPL=0 LDT
TR =0110 ffff5af0 00000067 00008b00 DPL=0 TSS32-busy
GDT=     ffff5020 000002cf
IDT=     ffff52f0 000007ff
CR0=8001003b CR2=00000000 CR3=0100a000 CR4=00000230
DR0=00000000 DR1=00000000 DR2=00000000 DR3=00000000
DR6=ffff0ff0 DR7=00000400
EFER=0000000000000000
Code=08 89 01 89 51 04 c3 8b 4c 24 08 8b 01 8b 51 04 8b 4c 24 04 <0f>
30 c3 f7 05 a4 6d ff ff 10 00 00 00 74 03 0f 31 c3 33 c0 33 d2 c3 8d
74 26 00 0f 31 c3

Signed-off-by: Lev Kujawski <lkujaw@member.fsf.org>
Message-Id: <20220521081511.187388-1-lkujaw@member.fsf.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

intel_th: pci: Add Raptor Lake-S CPU support

[ Upstream commit ff46a601afc5a66a81c3945b83d0a2caeb88e8bc ]

Add support for the Trace Hub in Raptor Lake-S CPU.

Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Link: https://lore.kernel.org/r/20220705082637.59979-7-alexander.shishkin@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

intel_th: pci: Add Raptor Lake-S PCH support

[ Upstream commit 23e2de5826e2fc4dd43e08bab3a2ea1a5338b063 ]

Add support for the Trace Hub in Raptor Lake-S PCH.

Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Link: https://lore.kernel.org/r/20220705082637.59979-6-alexander.shishkin@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

intel_th: pci: Add Meteor Lake-P support

[ Upstream commit 802a9a0b1d91274ef10d9fe429b4cc1e8c200aef ]

Add support for the Trace Hub in Meteor Lake-P.

Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Link: https://lore.kernel.org/r/20220705082637.59979-5-alexander.shishkin@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

scsi: lpfc: Remove extra atomic_inc on cmd_pending in queuecommand after VMID

[ Upstream commit 0948a9c5386095baae4012190a6b65aba684a907 ]

VMID introduced an extra increment of cmd_pending, causing double-counting
of the I/O. The normal increment ios performed in lpfc_get_scsi_buf.

Link: https://lore.kernel.org/r/20220701211425.2708-5-jsmart2021@gmail.com
Fixes: 33c79741deaf ("scsi: lpfc: vmid: Introduce VMID in I/O path")
Cc: <stable@vger.kernel.org> # v5.14+
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

scsi: lpfc: SLI path split: Refactor SCSI paths

[ Upstream commit 3512ac0942938d6977e7999ee69765d948d2faf1 ]

This patch refactors the SCSI paths to use SLI-4 as the primary interface.

 - Conversion away from using SLI-3 iocb structures to set/access fields in
   common routines. Use the new generic get/set routines that were added.
   This move changes code from indirect structure references to using local
   variables with the generic routines.

 - Refactor routines when setting non-generic fields, to have both SLI3 and
   SLI4 specific sections. This replaces the set-as-SLI3 then translate to
   SLI4 behavior of the past.

Link: https://lore.kernel.org/r/20220225022308.16486-14-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

scsi: lpfc: SLI path split: Refactor fast and slow paths to native SLI4

[ Upstream commit 1b64aa9eae28ac598a03ed3d62a63ac5e5b295fc ]

Convert the SLI4 fast and slow paths to use native SLI4 wqe constructs
instead of iocb SLI3-isms.

Includes the following:

 - Create simple get_xxx and set_xxx routines to wrapper access to common
   elements in both SLI3 and SLI4 commands - allowing calling routines to
   avoid sli-rev-specific structures to access the elements.

 - using the wqe in the job structure as the primary element

 - use defines from SLI-4, not SLI-3

 - Removal of iocb to wqe conversion from fast and slow path

 - Add below routines to handle fast path
lpfc_prep_embed_io - prepares the wqe for fast path
lpfc_wqe_bpl2sgl   - manages bpl to sgl conversion
lpfc_sli_wqe2iocb  - converts a WQE to IOCB for SLI-3 path

 - Add lpfc_sli3_iocb2wcqecmpl in completion path to convert an SLI-3
   iocb completion to wcqe completion

 - Refactor some of the code that works on both revs for clarity

Link: https://lore.kernel.org/r/20220225022308.16486-3-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

scsi: lpfc: SLI path split: Refactor lpfc_iocbq

[ Upstream commit a680a9298e7b4ff344aca3456177356b276e5038 ]

Currently, SLI3 and SLI4 data paths use the same lpfc_iocbq structure.
This is a "common" structure but many of the components refer to sli-rev
specific entities which can lead the developer astray as to what they
actually mean, should be set to, or when they should be used.

This first patch prepares the lpfc_iocbq structure so that elements common
to both SLI3 and SLI4 data paths are more appropriately named, making it
clear they apply generically.

Fieldnames based on 'iocb' (sli3) or 'wqe' (sli4) which are actually
generic to the paths are renamed to 'cmd':

 - iocb_flag is renamed to cmd_flag

 - lpfc_vmid_iocb_tag is renamed to lpfc_vmid_tag

 - fabric_iocb_cmpl is renamed to fabric_cmd_cmpl

 - wait_iocb_cmpl is renamed to wait_cmd_cmpl

 - iocb_cmpl and wqe_cmpl are combined and renamed to cmd_cmpl

 - rsvd2 member is renamed to num_bdes due to pre-existing usage

The structure name itself will retain the iocb reference as changing to a
more relevant "job" or "cmd" title induces many hundreds of line changes
for only a name change.

lpfc_post_buffer is also renamed to lpfc_sli3_post_buffer to indicate use
in the SLI3 path only.

Link: https://lore.kernel.org/r/20220225022308.16486-2-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

scsi: lpfc: Fix EEH support for NVMe I/O

[ Upstream commit 25ac2c970be32993f1dff607f8354f3c053d42bc ]

Injecting errors on the PCI slot while the driver is handling NVMe I/O will
cause crashes and hangs.

There are several rather difficult scenarios occurring. The main issue is
that the adapter can report a PCI error before or simultaneously to the PCI
subsystem reporting the error. Both paths have different entry points and
currently there is no interlock between them. Thus multiple teardown paths
are competing and all heck breaks loose.

Complicating things is the NVMs path. To a large degree, I/O was able to be
shutdown for a full FC port on the SCSI stack. But on NVMe, there isn't a
similar call. At best, it works on a per-controller basis, but even at the
controller level, it's a controller "reset" call. All of which means I/O is
still flowing on different CPUs with reset paths expecting hw access
(mailbox commands) to execute properly.

The following modifications are made:

 - A new flag is set in PCI error entrypoints so the driver can track being
   called by that path.

 - An interlock is added in the SLI hw error path and the PCI error path
   such that only one of the paths proceeds with the teardown logic.

 - RPI cleanup is patched such that RPIs are marked unregistered w/o mbx
   cmds in cases of hw error.

 - If entering the SLI port re-init calls, a case where SLI error teardown
   was quick and beat the PCI calls now reporting error, check whether the
   SLI port is still live on the PCI bus.

 - In the PCI reset code to bring the adapter back, recheck the IRQ
   settings. Different checks for SLI3 vs SLI4.

 - In I/O completions, that may be called as part of the cleanup or
   underway just before the hw error, check the state of the adapter.  If
   in error, shortcut handling that would expect further adapter
   completions as the hw error won't be sending them.

 - In routines waiting on I/O completions, which may have been in progress
   prior to the hw error, detect the device is being torn down and abort
   from their waits and just give up. This points to a larger issue in the
   driver on ref-counting for data structures, as it doesn't have
   ref-counting on q and port structures. We'll do this fix for now as it
   would be a major rework to be done differently.

 - Fix the NVMe cleanup to simulate NVMe I/O completions if I/O is being
   failed back due to hw error.

 - In I/O buf allocation, done at the start of new I/Os, check hw state and
   fail if hw error.

Link: https://lore.kernel.org/r/20210910233159.115896-10-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

firmware: arm_scpi: Ensure scpi_info is not assigned if the probe fails

[ Upstream commit 689640efc0a2c4e07e6f88affe6d42cd40cc3f85 ]

When scpi probe fails, at any point, we need to ensure that the scpi_info
is not set and will remain NULL until the probe succeeds. If it is not
taken care, then it could result use-after-free as the value is exported
via get_scpi_ops() and could refer to a memory allocated via devm_kzalloc()
but freed when the probe fails.

Link: https://lore.kernel.org/r/20220701160310.148344-1-sudeep.holla@arm.com
Cc: stable@vger.kernel.org # 4.19+
Reported-by: huhai <huhai@kylinos.cn>
Reviewed-by: Jackie Liu <liuyun01@kylinos.cn>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

usbnet: smsc95xx: Fix deadlock on runtime resume

[ Upstream commit 7b960c967f2aa01ab8f45c5a0bd78e754cffdeee ]

Commit 05b35e7eb9a1 ("smsc95xx: add phylib support") amended
smsc95xx_resume() to call phy_init_hw().  That function waits for the
device to runtime resume even though it is placed in the runtime resume
path, causing a deadlock.

The problem is that phy_init_hw() calls down to smsc95xx_mdiobus_read(),
which never uses the _nopm variant of usbnet_read_cmd().

Commit b4df480f68ae ("usbnet: smsc95xx: add reset_resume function with
reset operation") causes a similar deadlock on resume if the device was
already runtime suspended when entering system sleep:

That's because the commit introduced smsc95xx_reset_resume(), which
calls down to smsc95xx_reset(), which neglects to use _nopm accessors.

Fix by auto-detecting whether a device access is performed by the
suspend/resume task_struct and use the _nopm variant if so.  This works
because the PM core guarantees that suspend/resume callbacks are run in
task context.

Stacktrace for posterity:

  INFO: task kworker/2:1:49 blocked for more than 122 seconds.
  Workqueue: usb_hub_wq hub_event
  schedule
  rpm_resume
  __pm_runtime_resume
  usb_autopm_get_interface
  usbnet_read_cmd
  __smsc95xx_read_reg
  __smsc95xx_phy_wait_not_busy
  __smsc95xx_mdio_read
  smsc95xx_mdiobus_read
  __mdiobus_read
  mdiobus_read
  smsc_phy_reset
  phy_init_hw
  smsc95xx_resume
  usb_resume_interface
  usb_resume_both
  usb_runtime_resume
  __rpm_callback
  rpm_callback
  rpm_resume
  __pm_runtime_resume
  usb_autoresume_device
  hub_event
  process_one_work

Fixes: b4df480f68ae ("usbnet: smsc95xx: add reset_resume function with reset operation")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v3.16+
Cc: Andre Edich <andre.edich@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

usbnet: smsc95xx: Forward PHY interrupts to PHY driver to avoid polling

[ Upstream commit 1ce8b37241ed291af56f7a49bbdbf20c08728e88 ]

Link status of SMSC LAN95xx chips is polled once per second, even though
they're capable of signaling PHY interrupts through the MAC layer.

Forward those interrupts to the PHY driver to avoid polling.  Benefits
are reduced bus traffic, reduced CPU overhead and quicker interface
bringup.

Polling was introduced in 2016 by commit d69d16949346 ("usbnet:
smsc95xx: fix link detection for disabled autonegotiation").
Back then, the LAN95xx driver neglected to enable the ENERGYON interrupt,
hence couldn't detect link-up events when auto-negotiation was disabled.
The proper solution would have been to enable the ENERGYON interrupt
instead of polling.

Since then, PHY handling was moved from the LAN95xx driver to the SMSC
PHY driver with commit 05b35e7eb9a1 ("smsc95xx: add phylib support").
That PHY driver is capable of link detection with auto-negotiation
disabled because it enables the ENERGYON interrupt.

Note that signaling interrupts through the MAC layer not only works with
the integrated PHY, but also with an external PHY, provided its
interrupt pin is attached to LAN95xx's nPHY_INT pin.

In the unlikely event that the interrupt pin of an external PHY is
attached to a GPIO of the SoC (or not connected at all), the driver can
be amended to retrieve the irq from the PHY's of_node.

To forward PHY interrupts to phylib, it is not sufficient to call
phy_mac_interrupt().  Instead, the PHY's interrupt handler needs to run
so that PHY interrupts are cleared.  That's because according to page
119 of the LAN950x datasheet, "The source of this interrupt is a level.
The interrupt persists until it is cleared in the PHY."

https://www.microchip.com/content/dam/mchp/documents/UNG/ProductDocuments/DataSheets/LAN950x-Data-Sheet-DS00001875D.pdf

Therefore, create an IRQ domain with a single IRQ for the PHY.  In the
future, the IRQ domain may be extended to support the 11 GPIOs on the
LAN95xx.

Normally the PHY interrupt should be masked until the PHY driver has
cleared it.  However masking requires a (sleeping) USB transaction and
interrupts are received in (non-sleepable) softirq context.  I decided
not to mask the interrupt at all (by using the dummy_irq_chip's noop
->irq_mask() callback):  The USB interrupt endpoint is polled in 1 msec
intervals and normally that's sufficient to wake the PHY driver's IRQ
thread and have it clear the interrupt.  If it does take longer, worst
thing that can happen is the IRQ thread is woken again.  No big deal.

Because PHY interrupts are now perpetually enabled, there's no need to
selectively enable them on suspend.  So remove all invocations of
smsc95xx_enable_phy_wakeup_interrupts().

In smsc95xx_resume(), move the call of phy_init_hw() before
usbnet_resume() (which restarts the status URB) to ensure that the PHY
is fully initialized when an interrupt is handled.

Tested-by: Oleksij Rempel <o.rempel@pengutronix.de> # LAN9514/9512/9500
Tested-by: Ferry Toth <fntoth@gmail.com> # LAN9514
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch> # from a PHY perspective
Cc: Andre Edich <andre.edich@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

usbnet: smsc95xx: Avoid link settings race on interrupt reception

[ Upstream commit 8960f878e39fadc03d74292a6731f1e914cf2019 ]

When a PHY interrupt is signaled, the SMSC LAN95xx driver updates the
MAC full duplex mode and PHY flow control registers based on cached data
in struct phy_device:

  smsc95xx_status()                 # raises EVENT_LINK_RESET
    usbnet_deferred_kevent()
      smsc95xx_link_reset()         # uses cached data in phydev

Simultaneously, phylib polls link status once per second and updates
that cached data:

  phy_state_machine()
    phy_check_link_status()
      phy_read_status()
        lan87xx_read_status()
          genphy_read_status()      # updates cached data in phydev

If smsc95xx_link_reset() wins the race against genphy_read_status(),
the registers may be updated based on stale data.

E.g. if the link was previously down, phydev->duplex is set to
DUPLEX_UNKNOWN and that's what smsc95xx_link_reset() will use, even
though genphy_read_status() may update it to DUPLEX_FULL afterwards.

PHY interrupts are currently only enabled on suspend to trigger wakeup,
so the impact of the race is limited, but we're about to enable them
perpetually.

Avoid the race by delaying execution of smsc95xx_link_reset() until
phy_state_machine() has done its job and calls back via
smsc95xx_handle_link_change().

Signaling EVENT_LINK_RESET on wakeup is not necessary because phylib
picks up link status changes through polling.  So drop the declaration
of a ->link_reset() callback.

Note that the semicolon on a line by itself added in smsc95xx_status()
is a placeholder for a function call which will be added in a subsequent
commit.  That function call will actually handle the INT_ENP_PHY_INT_
interrupt.

Tested-by: Oleksij Rempel <o.rempel@pengutronix.de> # LAN9514/9512/9500
Tested-by: Ferry Toth <fntoth@gmail.com> # LAN9514
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

usbnet: smsc95xx: Don't clear read-only PHY interrupt

[ Upstream commit 3108871f19221372b251f7da1ac38736928b5b3a ]

Upon receiving data from the Interrupt Endpoint, the SMSC LAN95xx driver
attempts to clear the signaled interrupts by writing "all ones" to the
Interrupt Status Register.

However the driver only ever enables a single type of interrupt, namely
the PHY Interrupt.  And according to page 119 of the LAN950x datasheet,
its bit in the Interrupt Status Register is read-only.  There's no other
way to clear it than in a separate PHY register:

https://www.microchip.com/content/dam/mchp/documents/UNG/ProductDocuments/DataSheets/LAN950x-Data-Sheet-DS00001875D.pdf

Consequently, writing "all ones" to the Interrupt Status Register is
pointless and can be dropped.

Tested-by: Oleksij Rempel <o.rempel@pengutronix.de> # LAN9514/9512/9500
Tested-by: Ferry Toth <fntoth@gmail.com> # LAN9514
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/vc4: drv: Adopt the dma configuration from the HVS or V3D component

[ Upstream commit da8e393e23efb60eba8959856c7df88f9859f6eb ]

vc4_drv isn't necessarily under the /soc node in DT as it is a
virtual device, but it is the one that does the allocations.
The DMA addresses are consumed by primarily the HVS or V3D, and
those require VideoCore cache alias address mapping, and so will be
under /soc.

During probe find the a suitable device node for HVS or V3D,
and adopt the DMA configuration of that node.

Cc: <stable@vger.kernel.org>
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20220613144800.326124-2-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/dp/mst: Read the extended DPCD capabilities during system resume

[ Upstream commit 7a710a8bc909313951eb9252d8419924c771d7c2 ]

The WD22TB4 Thunderbolt dock at least will revert its DP_MAX_LINK_RATE
from HBR3 to HBR2 after system suspend/resume if the DP_DP13_DPCD_REV
registers are not read subsequently also as required.

Fix this by reading DP_DP13_DPCD_REV registers as well, matching what is
done during connector detection. While at it also fix up the same call
in drm_dp_mst_dump_topology().

Cc: Lyude Paul <lyude@redhat.com>
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/5292
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Cc: <stable@vger.kernel.org> # v5.14+
Reviewed-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220614094537.885472-1-imre.deak@intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

crypto: blake2s - remove shash module

[ Upstream commit 2d16803c562ecc644803d42ba98a8e0aef9c014e ]

BLAKE2s has no currently known use as an shash. Just remove all of this
unnecessary plumbing. Removing this shash was something we talked about
back when we were making BLAKE2s a built-in, but I simply never got
around to doing it. So this completes that project.

Importantly, this fixs a bug in which the lib code depends on
crypto_simd_disabled_for_test, causing linker errors.

Also add more alignment tests to the selftests and compare SIMD and
non-SIMD compression functions, to make up for what we lose from
testmgr.c.

Reported-by: gaochao <gaochao49@huawei.com>
Cc: Eric Biggers <ebiggers@kernel.org>
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: stable@vger.kernel.org
Fixes: 6048fdcc5f26 ("lib/crypto: blake2s: include as built-in")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/mediatek: Keep dsi as LP00 before dcs cmds transfer

[ Upstream commit 39e8d062b03c3dc257d880d82bd55cdd9e185a3b ]

To comply with the panel sequence, hold the mipi signal to LP00 before
the dcs cmds transmission, and pull the mipi signal high from LP00 to
LP11 until the start of the dcs cmds transmission.

The normal panel timing is :
(1) pp1800 DC pull up
(2) avdd & avee AC pull high
(3) lcm_reset pull high -> pull low -> pull high
(4) Pull MIPI signal high (LP11) -> initial code -> send video data
    (HS mode)

The power-off sequence is reversed.
If dsi is not in cmd mode, then dsi will pull the mipi signal high in
the mtk_output_dsi_enable function. The delay in lane_ready func is
the reaction time of dsi_rx after pulling up the mipi signal.

Fixes: 2dd8075d2185 ("drm/mediatek: mtk_dsi: Use the drm_panel_bridge API")

Link: https://patchwork.kernel.org/project/linux-mediatek/patch/1653012007-11854-4-git-send-email-xinlei.lee@mediatek.com/
Cc: <stable@vger.kernel.org> # 5.10.x: 7f6335c6a258: drm/mediatek: Modify dsi funcs to atomic operations
Cc: <stable@vger.kernel.org> # 5.10.x: cde7e2e35c28: drm/mediatek: Separate poweron/poweroff from enable/disable and define new funcs
Cc: <stable@vger.kernel.org> # 5.10.x
Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
Signed-off-by: Xinlei Lee <xinlei.lee@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/mediatek: Allow commands to be sent during video mode

[ Upstream commit 81cc7e51c4f1686b71e30046437056ece6b2cb4d ]

Mipi dsi panel drivers can use mipi_dsi_dcs_{set,get}_display_brightness()
to request backlight changes.

This can be done during panel initialization (dsi is in command mode)
or afterwards (dsi is in Video Mode).

When the DSI is in Video Mode, all commands are rejected.

Detect current DSI mode in mtk_dsi_host_transfer() and switch modes
temporarily to allow commands to be sent.

Signed-off-by: Julien STEPHAN <jstephan@baylibre.com>
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

spmi: trace: fix stack-out-of-bound access in SPMI tracing functions

commit 2af28b241eea816e6f7668d1954f15894b45d7e3 upstream.

trace_spmi_write_begin() and trace_spmi_read_end() both call
memcpy() with a length of "len + 1".  This leads to one extra
byte being read beyond the end of the specified buffer.  Fix
this out-of-bound memory access by using a length of "len"
instead.

Here is a KASAN log showing the issue:

BUG: KASAN: stack-out-of-bounds in trace_event_raw_event_spmi_read_end+0x1d0/0x234
Read of size 2 at addr ffffffc0265b7540 by task thermal@2.0-ser/1314
...
Call trace:
 dump_backtrace+0x0/0x3e8
 show_stack+0x2c/0x3c
 dump_stack_lvl+0xdc/0x11c
 print_address_description+0x74/0x384
 kasan_report+0x188/0x268
 kasan_check_range+0x270/0x2b0
 memcpy+0x90/0xe8
 trace_event_raw_event_spmi_read_end+0x1d0/0x234
 spmi_read_cmd+0x294/0x3ac
 spmi_ext_register_readl+0x84/0x9c
 regmap_spmi_ext_read+0x144/0x1b0 [regmap_spmi]
 _regmap_raw_read+0x40c/0x754
 regmap_raw_read+0x3a0/0x514
 regmap_bulk_read+0x418/0x494
 adc5_gen3_poll_wait_hs+0xe8/0x1e0 [qcom_spmi_adc5_gen3]
 ...
 __arm64_sys_read+0x4c/0x60
 invoke_syscall+0x80/0x218
 el0_svc_common+0xec/0x1c8
 ...

addr ffffffc0265b7540 is located in stack of task thermal@2.0-ser/1314 at offset 32 in frame:
 adc5_gen3_poll_wait_hs+0x0/0x1e0 [qcom_spmi_adc5_gen3]

this frame has 1 object:
 [32, 33) 'status'

Memory state around the buggy address:
 ffffffc0265b7400: 00 00 00 00 00 00 00 00 00 00 00 00 f1 f1 f1 f1
 ffffffc0265b7480: 04 f3 f3 f3 00 00 00 00 00 00 00 00 00 00 00 00
>ffffffc0265b7500: 00 00 00 00 f1 f1 f1 f1 01 f3 f3 f3 00 00 00 00
                                           ^
 ffffffc0265b7580: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
 ffffffc0265b7600: f1 f1 f1 f1 01 f2 07 f2 f2 f2 01 f3 00 00 00 00
==================================================================

Fixes: a9fce374815d ("spmi: add command tracepoints for SPMI")
Cc: stable@vger.kernel.org
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Acked-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: David Collins <quic_collinsd@quicinc.com>
Link: https://lore.kernel.org/r/20220627235512.2272783-1-quic_collinsd@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

__follow_mount_rcu(): verify that mount_lock remains unchanged

commit 20aac6c60981f5bfacd66661d090d907bf1482f0 upstream.

Validate mount_lock seqcount as soon as we cross into mount in RCU
mode.  Sure, ->mnt_root is pinned and will remain so until we
do rcu_read_unlock() anyway, and we will eventually fail to unlazy if
the mount_lock had been touched, but we might run into a hard error
(e.g. -ENOENT) before trying to unlazy.  And it's possible to end
up with RCU pathwalk racing with rename() and umount() in a way
that would fail with -ENOENT while non-RCU pathwalk would've
succeeded with any timings.

Once upon a time we hadn't needed that, but analysis had been subtle,
brittle and went out of window as soon as RENAME_EXCHANGE had been
added.

It's narrow, hard to hit and won't get you anything other than
stray -ENOENT that could be arranged in much easier way with the
same priveleges, but it's a bug all the same.

Cc: stable@kernel.org
X-sky-is-falling: unlikely
Fixes: da1ce0670c14 "vfs: add cross-rename"
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Input: gscps2 - check return value of ioremap() in gscps2_probe()

commit e61b3125a4f036b3c6b87ffd656fc1ab00440ae9 upstream.

The function ioremap() in gscps2_probe() can fail, so
its return value should be checked.

Fixes: 4bdc0d676a643 ("remove ioremap_nocache and devm_ioremap_nocache")
Cc: <stable@vger.kernel.org> # v5.6+
Reported-by: Hacash Robot <hacashRobot@santino.com>
Signed-off-by: Xie Shaowen <studentxswpy@163.com>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

posix-cpu-timers: Cleanup CPU timers before freeing them during exec

commit e362359ace6f87c201531872486ff295df306d13 upstream.

Commit 55e8c8eb2c7b ("posix-cpu-timers: Store a reference to a pid not a
task") started looking up tasks by PID when deleting a CPU timer.

When a non-leader thread calls execve, it will switch PIDs with the leader
process. Then, as it calls exit_itimers, posix_cpu_timer_del cannot find
the task because the timer still points out to the old PID.

That means that armed timers won't be disarmed, that is, they won't be
removed from the timerqueue_list. exit_itimers will still release their
memory, and when that list is later processed, it leads to a
use-after-free.

Clean up the timers from the de-threaded task before freeing them. This
prevents a reported use-after-free.

Fixes: 55e8c8eb2c7b ("posix-cpu-timers: Store a reference to a pid not a task")
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220809170751.164716-1-cascardo@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

SMB3: fix lease break timeout when multiple deferred close handles for the same file.

commit 9e31678fb403eae0f4fe37c6374be098835c73cd upstream.

Solution is to send lease break ack immediately even in case of
deferred close handles to avoid lease break request timing out
and let deferred closed handle gets closed as scheduled.
Later patches could optimize cases where we then close some
of these handles sooner for the cases where lease break is to 'none'

Cc: stable@kernel.org
Signed-off-by: Bharath SM <bharathsm@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

x86/olpc: fix 'logical not is only applied to the left hand side'

commit 3a2ba42cbd0b669ce3837ba400905f93dd06c79f upstream.

The bitops compile-time optimization series revealed one more
problem in olpc-xo1-sci.c:send_ebook_state(), resulted in GCC
warnings:

arch/x86/platform/olpc/olpc-xo1-sci.c: In function 'send_ebook_state':
arch/x86/platform/olpc/olpc-xo1-sci.c:83:63: warning: logical not is only applied to the left hand side of comparison [-Wlogical-not-parentheses]
   83 |         if (!!test_bit(SW_TABLET_MODE, ebook_switch_idev->sw) == state)
      |                                                               ^~
arch/x86/platform/olpc/olpc-xo1-sci.c:83:13: note: add parentheses around left hand side expression to silence this warning

Despite this code working as intended, this redundant double
negation of boolean value, together with comparing to `char`
with no explicit conversion to bool, makes compilers think
the author made some unintentional logical mistakes here.
Make it the other way around and negate the char instead
to silence the warnings.

Fixes: d2aa37411b8e ("x86/olpc/xo1/sci: Produce wakeup events for buttons and switches")
Cc: stable@vger.kernel.org # 3.5+
Reported-by: Guenter Roeck <linux@roeck-us.net>
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-and-tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Signed-off-by: Yury Norov <yury.norov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

x86/kprobes: Update kcb status flag after singlestepping

commit dec8784c9088b131a1523f582c2194cfc8107dc0 upstream.

Fix kprobes to update kcb (kprobes control block) status flag to
KPROBE_HIT_SSDONE even if the kp->post_handler is not set.

This bug may cause a kernel panic if another INT3 user runs right
after kprobes because kprobe_int3_handler() misunderstands the
INT3 is kprobe's single stepping INT3.

Fixes: 6256e668b7af ("x86/kprobes: Use int3 instead of debug trap for single-step")
Reported-by: Daniel Müller <deso@posteo.net>
Signed-off-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Tested-by: Daniel Müller <deso@posteo.net>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/all/20220727210136.jjgc3lpqeq42yr3m@muellerd-fedora-PC2BDTX9
Link: https://lore.kernel.org/r/165942025658.342061.12452378391879093249.stgit@devnote2
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ftrace/x86: Add back ftrace_expected assignment

commit ac6c1b2ca77e722a1e5d651f12f437f2f237e658 upstream.

When a ftrace_bug happens (where ftrace fails to modify a location) it is
helpful to have what was at that location as well as what was expected to
be there.

But with the conversion to text_poke() the variable that assigns the
expected for debugging was dropped. Unfortunately, I noticed this when I
needed it. Add it back.

Link: https://lkml.kernel.org/r/20220726101851.069d2e70@gandalf.local.home
Cc: "x86@kernel.org" <x86@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: stable@vger.kernel.org
Fixes: 768ae4406a5c ("x86/ftrace: Use text_poke()")
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

x86/bugs: Enable STIBP for IBPB mitigated RETBleed

commit e6cfcdda8cbe81eaf821c897369a65fec987b404 upstream.

AMD's "Technical Guidance for Mitigating Branch Type Confusion,
Rev. 1.0 2022-07-12" whitepaper, under section 6.1.2 "IBPB On
Privileged Mode Entry / SMT Safety" says:

  Similar to the Jmp2Ret mitigation, if the code on the sibling thread
  cannot be trusted, software should set STIBP to 1 or disable SMT to
  ensure SMT safety when using this mitigation.

So, like already being done for retbleed=unret, and now also for
retbleed=ibpb, force STIBP on machines that have it, and report its SMT
vulnerability status accordingly.

 [ bp: Remove the "we" and remove "[AMD]" applicability parameter which
   doesn't work here. ]

Fixes: 3ebc17006888 ("x86/bugs: Add retbleed=ibpb")
Signed-off-by: Kim Phillips <kim.phillips@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: stable@vger.kernel.org # 5.10, 5.15, 5.19
Link: https://bugzilla.kernel.org/show_bug.cgi?id=206537
Link: https://lore.kernel.org/r/20220804192201.439596-1-kim.phillips@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: qla2xxx: Fix losing FCP-2 targets during port perturbation tests

commit 58d1c124cd79ea686b512043c5bd515590b2ed95 upstream.

When a mix of FCP-2 (tape) and non-FCP-2 targets are present, FCP-2 target
state was incorrectly transitioned when both of the targets were gone. Fix
this by ignoring state transition for FCP-2 targets.

Link: https://lore.kernel.org/r/20220616053508.27186-7-njavali@marvell.com
Fixes: 44c57f205876 ("scsi: qla2xxx: Changes to support FCP2 Target")
Cc: stable@vger.kernel.org
Signed-off-by: Arun Easi <aeasi@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: qla2xxx: Fix losing target when it reappears during delete

commit 118b0c863c8f5629cc5271fc24d72d926e0715d9 upstream.

FC target disappeared during port perturbation tests due to a race that
tramples target state.  Fix the issue by adding state checks before
proceeding.

Link: https://lore.kernel.org/r/20220616053508.27186-8-njavali@marvell.com
Fixes: 44c57f205876 ("scsi: qla2xxx: Changes to support FCP2 Target")
Cc: stable@vger.kernel.org
Signed-off-by: Arun Easi <aeasi@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: qla2xxx: Fix losing FCP-2 targets on long port disable with I/Os

commit 2416ccd3815ba1613e10a6da0a24ef21acfe5633 upstream.

FCP-2 devices were not coming back online once they were lost, login
retries exhausted, and then came back up.  Fix this by accepting RSCN when
the device is not online.

Link: https://lore.kernel.org/r/20220616053508.27186-10-njavali@marvell.com
Fixes: 44c57f205876 ("scsi: qla2xxx: Changes to support FCP2 Target")
Cc: stable@vger.kernel.org
Signed-off-by: Arun Easi <aeasi@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: qla2xxx: Wind down adapter after PCIe error

commit d3117c83ba316b3200d9f2fe900f2b9a5525a25c upstream.

Put adapter into a wind down state if OS does not make any attempt to
recover the adapter after PCIe error.

Link: https://lore.kernel.org/r/20220616053508.27186-4-njavali@marvell.com
Cc: stable@vger.kernel.org
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: qla2xxx: Fix erroneous mailbox timeout after PCI error injection

commit f260694e6463b63ae550aad25ddefe94cb1904da upstream.

Clear wait for mailbox interrupt flag to prevent stale mailbox:

Feb 22 05:22:56 ltcden4-lp7 kernel: qla2xxx [0135:90:00.1]-500a:4: LOOP UP detected (16 Gbps).
Feb 22 05:22:59 ltcden4-lp7 kernel: qla2xxx [0135:90:00.1]-d04c:4: MBX Command timeout for cmd 69, ...

To fix the issue, driver needs to clear the MBX_INTR_WAIT flag on purging
the mailbox. When the stale mailbox completion does arrive, it will be
dropped.

Link: https://lore.kernel.org/r/20220616053508.27186-11-njavali@marvell.com
Fixes: b6faaaf796d7 ("scsi: qla2xxx: Serialize mailbox request")
Cc: Naresh Bannoth <nbannoth@in.ibm.com>
Cc: Kyle Mahlkuch <Kyle.Mahlkuch@ibm.com>
Cc: stable@vger.kernel.org
Reported-by: Naresh Bannoth <nbannoth@in.ibm.com>
Tested-by: Naresh Bannoth <nbannoth@in.ibm.com>
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: qla2xxx: Fix excessive I/O error messages by default

commit bff4873c709085e09d0ffae0c25b8e65256e3205 upstream.

Disable printing I/O error messages by default.  The messages will be
printed only when logging was enabled.

Link: https://lore.kernel.org/r/20220616053508.27186-2-njavali@marvell.com
Fixes: 8e2d81c6b5be ("scsi: qla2xxx: Fix excessive messages during device logout")
Cc: stable@vger.kernel.org
Signed-off-by: Arun Easi <aeasi@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: qla2xxx: Fix crash due to stale SRB access around I/O timeouts

commit c39587bc0abaf16593f7abcdf8aeec3c038c7d52 upstream.

Ensure SRB is returned during I/O timeout error escalation. If that is not
possible fail the escalation path.

Following crash stack was seen:

BUG: unable to handle kernel paging request at 0000002f56aa90f8
IP: qla_chk_edif_rx_sa_delete_pending+0x14/0x30 [qla2xxx]
Call Trace:
 ? qla2x00_status_entry+0x19f/0x1c50 [qla2xxx]
 ? qla2x00_start_sp+0x116/0x1170 [qla2xxx]
 ? dma_pool_alloc+0x1d6/0x210
 ? mempool_alloc+0x54/0x130
 ? qla24xx_process_response_queue+0x548/0x12b0 [qla2xxx]
 ? qla_do_work+0x2d/0x40 [qla2xxx]
 ? process_one_work+0x14c/0x390

Link: https://lore.kernel.org/r/20220616053508.27186-6-njavali@marvell.com
Fixes: d74595278f4a ("scsi: qla2xxx: Add multiple queue pair functionality.")
Cc: stable@vger.kernel.org
Signed-off-by: Arun Easi <aeasi@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: qla2xxx: Turn off multi-queue for 8G adapters

commit 5304673bdb1635e27555bd636fd5d6956f1cd552 upstream.

For 8G adapters, multi-queue was enabled accidentally. Make sure
multi-queue is not enabled.

Link: https://lore.kernel.org/r/20220616053508.27186-5-njavali@marvell.com
Cc: stable@vger.kernel.org
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: qla2xxx: Fix discovery issues in FC-AL topology

commit 47ccb113cead905bdc236571bf8ac6fed90321b3 upstream.

A direct attach tape device, when gets swapped with another, was not
discovered. Fix this by looking at loop map and reinitialize link if there
are devices present.

Link: https://lore.kernel.org/linux-scsi/baef87c3-5dad-3b47-44c1-6914bfc90108@cybernetics.com/
Link: https://lore.kernel.org/r/20220713052045.10683-8-njavali@marvell.com
Cc: stable@vger.kernel.org
Reported-by: Tony Battersby <tonyb@cybernetics.com>
Tested-by: Tony Battersby <tonyb@cybernetics.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Arun Easi <aeasi@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: qla2xxx: Fix imbalance vha->vref_count

commit 63fa7f2644b4b48e1913af33092c044bf48e9321 upstream.

vref_count took an extra decrement in the task management path.  Add an
extra ref count to compensate the imbalance.

Link: https://lore.kernel.org/r/20220713052045.10683-7-njavali@marvell.com
Cc: stable@vger.kernel.org
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: zfcp: Fix missing auto port scan and thus missing target ports

commit 4da8c5f76825269f28d6a89fa752934a4bcb6dfa upstream.

Case (1):
  The only waiter on wka_port->completion_wq is zfcp_fc_wka_port_get()
  trying to open a WKA port. As such it should only be woken up by WKA port
  *open* responses, not by WKA port close responses.

Case (2):
  A close WKA port response coming in just after having sent a new open WKA
  port request and before blocking for the open response with wait_event()
  in zfcp_fc_wka_port_get() erroneously renders the wait_event a NOP
  because the close handler overwrites wka_port->status. Hence the
  wait_event condition is erroneously true and it does not enter blocking
  state.

With non-negligible probability, the following time space sequence happens
depending on timing without this fix:

user process        ERP thread zfcp work queue tasklet system work queue
============        ========== =============== ======= =================
$ echo 1 > online
zfcp_ccw_set_online
zfcp_ccw_activate
zfcp_erp_adapter_reopen
msleep scan backoff zfcp_erp_strategy
|                   ...
|                   zfcp_erp_action_cleanup
|                   ...
|                   queue delayed scan_work
|                   queue ns_up_work
|                              ns_up_work:
|                              zfcp_fc_wka_port_get
|                               open wka request
|                                              open response
|                              GSPN FC-GS
|                              RSPN FC-GS [NPIV-only]
|                              zfcp_fc_wka_port_put
|                               (--wka->refcount==0)
|                               sched delayed wka->work
|
~~~Case (1)~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
zfcp_erp_wait
flush scan_work
|                                                      wka->work:
|                                                      wka->status=CLOSING
|                                                      close wka request
|                              scan_work:
|                              zfcp_fc_wka_port_get
|                               (wka->status==CLOSING)
|                               wka->status=OPENING
|                               open wka request
|                               wait_event
|                               |              close response
|                               |              wka->status=OFFLINE
|                               |              wake_up /*WRONG*/
~~~Case (2)~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
|                                                      wka->work:
|                                                      wka->status=CLOSING
|                                                      close wka request
zfcp_erp_wait
flush scan_work
|                              scan_work:
|                              zfcp_fc_wka_port_get
|                               (wka->status==CLOSING)
|                               wka->status=OPENING
|                               open wka request
|                                              close response
|                                              wka->status=OFFLINE
|                                              wake_up /*WRONG&NOP*/
|                               wait_event /*NOP*/
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
|                               (wka->status!=ONLINE)
|                               return -EIO
|                              return early
                                               open response
                                               wka->status=ONLINE
                                               wake_up /*NOP*/

So we erroneously end up with no automatic port scan. This is a big problem
when it happens during boot. The timing is influenced by v3.19 commit
18f87a67e6d6 ("zfcp: auto port scan resiliency").

Fix it by fully mutually excluding zfcp_fc_wka_port_get() and
zfcp_fc_wka_port_offline(). For that to work, we make the latter block
until we got the response for a close WKA port. In order not to penalize
the system workqueue, we move wka_port->work to our own adapter workqueue.
Note that before v2.6.30 commit 828bc1212a68 ("[SCSI] zfcp: Set WKA-port to
offline on adapter deactivation"), zfcp did block in
zfcp_fc_wka_port_offline() as well, but with a different condition.

While at it, make non-functional cleanups to improve code reading in
zfcp_fc_wka_port_get(). If we cannot send the WKA port open request, don't
rely on the subsequent wait_event condition to immediately let this case
pass without blocking. Also don't want to rely on the additional condition
handling the refcount to be skipped just to finally return with -EIO.

Link: https://lore.kernel.org/r/20220729162529.1620730-1-maier@linux.ibm.com
Fixes: 5ab944f97e09 ("[SCSI] zfcp: attach and release SAN nameserver port on demand")
Cc: <stable@vger.kernel.org> #v2.6.28+
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Steffen Maier <maier@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: ufs: core: Correct ufshcd_shutdown() flow

commit 00511d2abf5708ad05dd5d1c36adb2468d274698 upstream.

After ufshcd_wl_shutdown() set device power off and link off,
ufshcd_shutdown() could turn off clock/power. Also remove
pm_runtime_get_sync.

The reason why it is safe to remove pm_runtime_get_sync() is because:

 - ufshcd_wl_shutdown() -> pm_runtime_get_sync() will resume hba->dev too.

 - device resume(turn on clk/power) is not required, even if device is in
   RPM_SUSPENDED.

Link: https://lore.kernel.org/r/20220727030526.31022-1-peter.wang@mediatek.com
Fixes: b294ff3e3449 ("scsi: ufs: core: Enable power management for wlun")
Cc: <stable@vger.kernel.org> # 5.15.x
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Peter Wang <peter.wang@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

video: fbdev: s3fb: Check the size of screen before memset_io()

[ Upstream commit 6ba592fa014f21f35a8ee8da4ca7b95a018f13e8 ]

In the function s3fb_set_par(), the value of 'screen_size' is
calculated by the user input. If the user provides the improper value,
the value of 'screen_size' may larger than 'info->screen_size', which
may cause the following bug:

[   54.083733] BUG: unable to handle page fault for address: ffffc90003000000
[   54.083742] #PF: supervisor write access in kernel mode
[   54.083744] #PF: error_code(0x0002) - not-present page
[   54.083760] RIP: 0010:memset_orig+0x33/0xb0
[   54.083782] Call Trace:
[   54.083788]  s3fb_set_par+0x1ec6/0x4040
[   54.083806]  fb_set_var+0x604/0xeb0
[   54.083836]  do_fb_ioctl+0x234/0x670

Fix the this by checking the value of 'screen_size' before memset_io().

Fixes: a268422de8bf ("fbdev driver for S3 Trio/Virge")
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

video: fbdev: arkfb: Check the size of screen before memset_io()

[ Upstream commit 96b550971c65d54d64728d8ba973487878a06454 ]

In the function arkfb_set_par(), the value of 'screen_size' is
calculated by the user input. If the user provides the improper value,
the value of 'screen_size' may larger than 'info->screen_size', which
may cause the following bug:

[  659.399066] BUG: unable to handle page fault for address: ffffc90003000000
[  659.399077] #PF: supervisor write access in kernel mode
[  659.399079] #PF: error_code(0x0002) - not-present page
[  659.399094] RIP: 0010:memset_orig+0x33/0xb0
[  659.399116] Call Trace:
[  659.399122]  arkfb_set_par+0x143f/0x24c0
[  659.399130]  fb_set_var+0x604/0xeb0
[  659.399161]  do_fb_ioctl+0x234/0x670
[  659.399189]  fb_ioctl+0xdd/0x130

Fix the this by checking the value of 'screen_size' before memset_io().

Fixes: 681e14730c73 ("arkfb: new framebuffer driver for ARK Logic cards")
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

video: fbdev: vt8623fb: Check the size of screen before memset_io()

[ Upstream commit ec0754c60217248fa77cc9005d66b2b55200ac06 ]

In the function vt8623fb_set_par(), the value of 'screen_size' is
calculated by the user input. If the user provides the improper value,
the value of 'screen_size' may larger than 'info->screen_size', which
may cause the following bug:

[  583.339036] BUG: unable to handle page fault for address: ffffc90005000000
[  583.339049] #PF: supervisor write access in kernel mode
[  583.339052] #PF: error_code(0x0002) - not-present page
[  583.339074] RIP: 0010:memset_orig+0x33/0xb0
[  583.339110] Call Trace:
[  583.339118]  vt8623fb_set_par+0x11cd/0x21e0
[  583.339146]  fb_set_var+0x604/0xeb0
[  583.339181]  do_fb_ioctl+0x234/0x670
[  583.339209]  fb_ioctl+0xdd/0x130

Fix the this by checking the value of 'screen_size' before memset_io().

Fixes: 558b7bd86c32 ("vt8623fb: new framebuffer driver for VIA VT8623")
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

f2fs: do not allow to decompress files have FI_COMPRESS_RELEASED

[ Upstream commit 90be48bd9d29ece3965e5e8b21499b6db166e57b ]

If a file has FI_COMPRESS_RELEASED, all writes for it should not be
allowed. However, as of now, in case of compress_mode=user, writes
triggered by IOCTLs like F2FS_IOC_DE/COMPRESS_FILE are allowed unexpectly,
which could crash that file.
To fix it, let's do not allow F2FS_IOC_DE/COMPRESS_IOCTL if a file already
has FI_COMPRESS_RELEASED flag.

This is the reproduction process:
1.  $ touch ./file
2.  $ chattr +c ./file
3.  $ dd if=/dev/random of=./file bs=4096 count=30 conv=notrunc
4.  $ dd if=/dev/zero of=./file bs=4096 count=34 seek=30 conv=notrunc
5.  $ sync
6.  $ do_compress ./file      ; call F2FS_IOC_COMPRESS_FILE
7.  $ get_compr_blocks ./file ; call F2FS_IOC_GET_COMPRESS_BLOCKS
8.  $ release ./file          ; call F2FS_IOC_RELEASE_COMPRESS_BLOCKS
9.  $ do_compress ./file      ; call F2FS_IOC_COMPRESS_FILE again
10. $ get_compr_blocks ./file ; call F2FS_IOC_GET_COMPRESS_BLOCKS again

This reproduction process is tested in 128kb cluster size.
You can find compr_blocks has a negative value.

Fixes: 5fdb322ff2c2b ("f2fs: add F2FS_IOC_DECOMPRESS_FILE and F2FS_IOC_COMPRESS_FILE")

Signed-off-by: Junbeom Yeom <junbeom.yeom@samsung.com>
Signed-off-by: Sungjong Seo <sj1557.seo@samsung.com>
Signed-off-by: Youngjin Gil <youngjin.gil@samsung.com>
Signed-off-by: Jaewook Kim <jw5454.kim@samsung.com>
Reviewed-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

f2fs: allow compression for mmap files in compress_mode=user

[ Upstream commit 66d34fcbbe63ebd8584b792e0d741f6648100894 ]

Since commit e3c548323d32 ("f2fs: let's allow compression for mmap files"),
it has been allowed to compress mmap files. However, in compress_mode=user,
it is not allowed yet. To keep the same concept in both compress_modes,
f2fs_ioc_(de)compress_file() should also allow it.

Let's remove checking mmap files in f2fs_ioc_(de)compress_file() so that
the compression for mmap files is also allowed in compress_mode=user.

Signed-off-by: Sungjong Seo <sj1557.seo@samsung.com>
Reviewed-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

x86/entry: Build thunk_$(BITS) only if CONFIG_PREEMPTION=y

[ Upstream commit de979c83574abf6e78f3fa65b716515c91b2613d ]

With CONFIG_PREEMPTION disabled, arch/x86/entry/thunk_$(BITS).o becomes
an empty object file.

With some old versions of binutils (i.e., 2.35.90.20210113-1ubuntu1) the
GNU assembler doesn't generate a symbol table for empty object files and
objtool fails with the following error when a valid symbol table cannot
be found:

  arch/x86/entry/thunk_64.o: warning: objtool: missing symbol table

To prevent this from happening, build thunk_$(BITS).o only if
CONFIG_PREEMPTION is enabled.

BugLink: https://bugs.launchpad.net/bugs/1911359
Fixes: 320100a5ffe5 ("x86/entry: Remove the TRACE_IRQS cruft")
Signed-off-by: Andrea Righi <andrea.righi@canonical.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/Ys/Ke7EWjcX+ZlXO@arighi-desktop
Signed-off-by: Sasha Levin <sashal@kernel.org>

sched/core: Do not requeue task on CPU excluded from cpus_mask

[ Upstream commit 751d4cbc43879229dbc124afefe240b70fd29a85 ]

The following warning was triggered on a large machine early in boot on
a distribution kernel but the same problem should also affect mainline.

   WARNING: CPU: 439 PID: 10 at ../kernel/workqueue.c:2231 process_one_work+0x4d/0x440
   Call Trace:
    <TASK>
    rescuer_thread+0x1f6/0x360
    kthread+0x156/0x180
    ret_from_fork+0x22/0x30
    </TASK>

Commit c6e7bd7afaeb ("sched/core: Optimize ttwu() spinning on p->on_cpu")
optimises ttwu by queueing a task that is descheduling on the wakelist,
but does not check if the task descheduling is still allowed to run on that CPU.

In this warning, the problematic task is a workqueue rescue thread which
checks if the rescue is for a per-cpu workqueue and running on the wrong CPU.
While this is early in boot and it should be possible to create workers,
the rescue thread may still used if the MAYDAY_INITIAL_TIMEOUT is reached
or MAYDAY_INTERVAL and on a sufficiently large machine, the rescue
thread is being used frequently.

Tracing confirmed that the task should have migrated properly using the
stopper thread to handle the migration. However, a parallel wakeup from udev
running on another CPU that does not share CPU cache observes p->on_cpu and
uses task_cpu(p), queues the task on the old CPU and triggers the warning.

Check that the wakee task that is descheduling is still allowed to run
on its current CPU and if not, wait for the descheduling to complete
and select an allowed CPU.

Fixes: c6e7bd7afaeb ("sched/core: Optimize ttwu() spinning on p->on_cpu")
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20220804092119.20137-1-mgorman@techsingularity.net
Signed-off-by: Sasha Levin <sashal@kernel.org>

sched: Remove the limitation of WF_ON_CPU on wakelist if wakee cpu is idle

[ Upstream commit f3dd3f674555bd9455c5ae7fafce0696bd9931b3 ]

Wakelist can help avoid cache bouncing and offload the overhead of waker
cpu. So far, using wakelist within the same llc only happens on
WF_ON_CPU, and this limitation could be removed to further improve
wakeup performance.

The commit 518cd6234178 ("sched: Only queue remote wakeups when
crossing cache boundaries") disabled queuing tasks on wakelist when
the cpus share llc. This is because, at that time, the scheduler must
send IPIs to do ttwu_queue_wakelist. Nowadays, ttwu_queue_wakelist also
supports TIF_POLLING, so this is not a problem now when the wakee cpu is
in idle polling.

Benefits:
  Queuing the task on idle cpu can help improving performance on waker cpu
  and utilization on wakee cpu, and further improve locality because
  the wakee cpu can handle its own rq. This patch helps improving rt on
  our real java workloads where wakeup happens frequently.

  Consider the normal condition (CPU0 and CPU1 share same llc)
  Before this patch:

         CPU0                                       CPU1

    select_task_rq()                                idle
    rq_lock(CPU1->rq)
    enqueue_task(CPU1->rq)
    notify CPU1 (by sending IPI or CPU1 polling)

                                                    resched()

  After this patch:

         CPU0                                       CPU1

    select_task_rq()                                idle
    add to wakelist of CPU1
    notify CPU1 (by sending IPI or CPU1 polling)

                                                    rq_lock(CPU1->rq)
                                                    enqueue_task(CPU1->rq)
                                                    resched()

  We see CPU0 can finish its work earlier. It only needs to put task to
  wakelist and return.
  While CPU1 is idle, so let itself handle its own runqueue data.

This patch brings no difference about IPI.
  This patch only takes effect when the wakee cpu is:
  1) idle polling
  2) idle not polling

  For 1), there will be no IPI with or without this patch.

  For 2), there will always be an IPI before or after this patch.
  Before this patch: waker cpu will enqueue task and check preempt. Since
  "idle" will be sure to be preempted, waker cpu must send a resched IPI.
  After this patch: waker cpu will put the task to the wakelist of wakee
  cpu, and send an IPI.

Benchmark:
We've tested schbench, unixbench, and hachbench on both x86 and arm64.

On x86 (Intel Xeon Platinum 8269CY):
  schbench -m 2 -t 8

    Latency percentiles (usec)              before        after
        50.0000th:                             8            6
        75.0000th:                            10            7
        90.0000th:                            11            8
        95.0000th:                            12            8
        *99.0000th:                           13           10
        99.5000th:                            15           11
        99.9000th:                            18           14

  Unixbench with full threads (104)
                                            before        after
    Dhrystone 2 using register variables  3011862938    3009935994  -0.06%
    Double-Precision Whetstone              617119.3      617298.5   0.03%
    Execl Throughput                         27667.3       27627.3  -0.14%
    File Copy 1024 bufsize 2000 maxblocks   785871.4      784906.2  -0.12%
    File Copy 256 bufsize 500 maxblocks     210113.6      212635.4   1.20%
    File Copy 4096 bufsize 8000 maxblocks  2328862.2     2320529.1  -0.36%
    Pipe Throughput                      145535622.8   145323033.2  -0.15%
    Pipe-based Context Switching           3221686.4     3583975.4  11.25%
    Process Creation                        101347.1      103345.4   1.97%
    Shell Scripts (1 concurrent)            120193.5      123977.8   3.15%
    Shell Scripts (8 concurrent)             17233.4       17138.4  -0.55%
    System Call Overhead                   5300604.8     5312213.6   0.22%

  hackbench -g 1 -l 100000
                                            before        after
    Time                                     3.246        2.251

On arm64 (Ampere Altra):
  schbench -m 2 -t 8

    Latency percentiles (usec)              before        after
        50.0000th:                            14           10
        75.0000th:                            19           14
        90.0000th:                            22           16
        95.0000th:                            23           16
        *99.0000th:                           24           17
        99.5000th:                            24           17
        99.9000th:                            28           25

  Unixbench with full threads (80)
                                            before        after
    Dhrystone 2 using register variables  3536194249    3537019613   0.02%
    Double-Precision Whetstone              629383.6      629431.6   0.01%
    Execl Throughput                         65920.5       65846.2  -0.11%
    File Copy 1024 bufsize 2000 maxblocks  1063722.8     1064026.8   0.03%
    File Copy 256 bufsize 500 maxblocks     322684.5      318724.5  -1.23%
    File Copy 4096 bufsize 8000 maxblocks  2348285.3     2328804.8  -0.83%
    Pipe Throughput                      133542875.3   131619389.8  -1.44%
    Pipe-based Context Switching           3215356.1     3576945.1  11.25%
    Process Creation                        108520.5      120184.6  10.75%
    Shell Scripts (1 concurrent)            122636.3        121888  -0.61%
    Shell Scripts (8 concurrent)             17462.1       17381.4  -0.46%
    System Call Overhead                   4429998.9     4435006.7   0.11%

  hackbench -g 1 -l 100000
                                            before        after
    Time                                     4.217        2.916

Our patch has improvement on schbench, hackbench
and Pipe-based Context Switching of unixbench
when there exists idle cpus,
and no obvious regression on other tests of unixbench.
This can help improve rt in scenes where wakeup happens frequently.

Signed-off-by: Tianchen Ding <dtcccc@linux.alibaba.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Valentin Schneider <vschneid@redhat.com>
Link: https://lore.kernel.org/r/20220608233412.327341-3-dtcccc@linux.alibaba.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

sched: Fix the check of nr_running at queue wakelist

[ Upstream commit 28156108fecb1f808b21d216e8ea8f0d205a530c ]

The commit 2ebb17717550 ("sched/core: Offload wakee task activation if it
the wakee is descheduling") checked rq->nr_running <= 1 to avoid task
stacking when WF_ON_CPU.

Per the ordering of writes to p->on_rq and p->on_cpu, observing p->on_cpu
(WF_ON_CPU) in ttwu_queue_cond() implies !p->on_rq, IOW p has gone through
the deactivate_task() in __schedule(), thus p has been accounted out of
rq->nr_running. As such, the task being the only runnable task on the rq
implies reading rq->nr_running == 0 at that point.

The benchmark result is in [1].

[1] https://lore.kernel.org/all/e34de686-4e85-bde1-9f3c-9bbc86b38627@linux.alibaba.com/

Suggested-by: Valentin Schneider <vschneid@redhat.com>
Signed-off-by: Tianchen Ding <dtcccc@linux.alibaba.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Valentin Schneider <vschneid@redhat.com>
Link: https://lore.kernel.org/r/20220608233412.327341-2-dtcccc@linux.alibaba.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

tools/thermal: Fix possible path truncations

[ Upstream commit 6c58cf40e3a1d2f47c09d3489857e9476316788a ]

A build with -D_FORTIFY_SOURCE=2 enabled will produce the following warnings:

sysfs.c:63:30: warning: '%s' directive output may be truncated writing up to 255 bytes into a region of size between 0 and 255 [-Wformat-truncation=]
  snprintf(filepath, 256, "%s/%s", path, filename);
                              ^~
Bump up the buffer to PATH_MAX which is the limit and account for all of
the possible NUL and separators that could lead to exceeding the
allocated buffer sizes.

Fixes: 94f69966faf8 ("tools/thermal: Introduce tmon, a tool for thermal subsystem")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

video: fbdev: arkfb: Fix a divide-by-zero bug in ark_set_pixclock()

[ Upstream commit 2f1c4523f7a3aaabe7e53d3ebd378292947e95c8 ]

Since the user can control the arguments of the ioctl() from the user
space, under special arguments that may result in a divide-by-zero bug
in:
  drivers/video/fbdev/arkfb.c:784: ark_set_pixclock(info, (hdiv * info->var.pixclock) / hmul);
with hdiv=1, pixclock=1 and hmul=2 you end up with (1*1)/2 = (int) 0.
and then in:
  drivers/video/fbdev/arkfb.c:504: rv = dac_set_freq(par->dac, 0, 1000000000 / pixclock);
we'll get a division-by-zero.

The following log can reveal it:

divide error: 0000 [#1] PREEMPT SMP KASAN PTI
RIP: 0010:ark_set_pixclock drivers/video/fbdev/arkfb.c:504 [inline]
RIP: 0010:arkfb_set_par+0x10fc/0x24c0 drivers/video/fbdev/arkfb.c:784
Call Trace:
 fb_set_var+0x604/0xeb0 drivers/video/fbdev/core/fbmem.c:1034
 do_fb_ioctl+0x234/0x670 drivers/video/fbdev/core/fbmem.c:1110
 fb_ioctl+0xdd/0x130 drivers/video/fbdev/core/fbmem.c:1189

Fix this by checking the argument of ark_set_pixclock() first.

Fixes: 681e14730c73 ("arkfb: new framebuffer driver for ARK Logic cards")
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

x86/numa: Use cpumask_available instead of hardcoded NULL check

[ Upstream commit 625395c4a0f4775e0fe00f616888d2e6c1ba49db ]

GCC-12 started triggering a new warning:

  arch/x86/mm/numa.c: In function ‘cpumask_of_node’:
  arch/x86/mm/numa.c:916:39: warning: the comparison will always evaluate as ‘false’ for the address of ‘node_to_cpumask_map’ will never be NULL [-Waddress]
    916 |         if (node_to_cpumask_map[node] == NULL) {
        |                                       ^~

node_to_cpumask_map is of type cpumask_var_t[].

When CONFIG_CPUMASK_OFFSTACK is set, cpumask_var_t is typedef'd to a
pointer for dynamic allocation, else to an array of one element. The
"wicked game" can be checked on line 700 of include/linux/cpumask.h.

The original code in debug_cpumask_set_cpu() and cpumask_of_node() were
probably written by the original authors with CONFIG_CPUMASK_OFFSTACK=y
(i.e. dynamic allocation) in mind, checking if the cpumask was available
via a direct NULL check.

When CONFIG_CPUMASK_OFFSTACK is not set, GCC gives the above warning
while compiling the kernel.

Fix that by using cpumask_available(), which does the NULL check when
CONFIG_CPUMASK_OFFSTACK is set, otherwise returns true. Use it wherever
such checks are made.

Conditional definitions of cpumask_available() can be found along with
the definition of cpumask_var_t. Check the cpumask.h reference mentioned
above.

Fixes: c032ef60d1aa ("cpumask: convert node_to_cpumask_map[] to cpumask_var_t")
Fixes: de2d9445f162 ("x86: Unify node_to_cpumask_map handling between 32 and 64bit")
Signed-off-by: Siddh Raman Pant <code@siddh.me>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20220731160913.632092-1-code@siddh.me
Signed-off-by: Sasha Levin <sashal@kernel.org>

sched, cpuset: Fix dl_cpu_busy() panic due to empty cs->cpus_allowed

[ Upstream commit b6e8d40d43ae4dec00c8fea2593eeea3114b8f44 ]

With cgroup v2, the cpuset's cpus_allowed mask can be empty indicating
that the cpuset will just use the effective CPUs of its parent. So
cpuset_can_attach() can call task_can_attach() with an empty mask.
This can lead to cpumask_any_and() returns nr_cpu_ids causing the call
to dl_bw_of() to crash due to percpu value access of an out of bound
CPU value. For example:

[80468.182258] BUG: unable to handle page fault for address: ffffffff8b6648b0
  :
[80468.191019] RIP: 0010:dl_cpu_busy+0x30/0x2b0
  :
[80468.207946] Call Trace:
[80468.208947]  cpuset_can_attach+0xa0/0x140
[80468.209953]  cgroup_migrate_execute+0x8c/0x490
[80468.210931]  cgroup_update_dfl_csses+0x254/0x270
[80468.211898]  cgroup_subtree_control_write+0x322/0x400
[80468.212854]  kernfs_fop_write_iter+0x11c/0x1b0
[80468.213777]  new_sync_write+0x11f/0x1b0
[80468.214689]  vfs_write+0x1eb/0x280
[80468.215592]  ksys_write+0x5f/0xe0
[80468.216463]  do_syscall_64+0x5c/0x80
[80468.224287]  entry_SYSCALL_64_after_hwframe+0x44/0xae

Fix that by using effective_cpus instead. For cgroup v1, effective_cpus
is the same as cpus_allowed. For v2, effective_cpus is the real cpumask
to be used by tasks within the cpuset anyway.

Also update task_can_attach()'s 2nd argument name to cs_effective_cpus to
reflect the change. In addition, a check is added to task_can_attach()
to guard against the possibility that cpumask_any_and() may return a
value >= nr_cpu_ids.

Fixes: 7f51412a415d ("sched/deadline: Fix bandwidth check/update when migrating tasks between exclusive cpusets")
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Juri Lelli <juri.lelli@redhat.com>
Link: https://lore.kernel.org/r/20220803015451.2219567-1-longman@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

sched/deadline: Merge dl_task_can_attach() and dl_cpu_busy()

[ Upstream commit 772b6539fdda31462cc08368e78df60b31a58bab ]

Both functions are doing almost the same, that is checking if admission
control is still respected.

With exclusive cpusets, dl_task_can_attach() checks if the destination
cpuset (i.e. its root domain) has enough CPU capacity to accommodate the
task.
dl_cpu_busy() checks if there is enough CPU capacity in the cpuset in
case the CPU is hot-plugged out.

dl_task_can_attach() is used to check if a task can be admitted while
dl_cpu_busy() is used to check if a CPU can be hotplugged out.

Make dl_cpu_busy() able to deal with a task and use it instead of
dl_task_can_attach() in task_can_attach().

Signed-off-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Juri Lelli <juri.lelli@redhat.com>
Link: https://lore.kernel.org/r/20220302183433.333029-4-dietmar.eggemann@arm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

scripts/faddr2line: Fix vmlinux detection on arm64

[ Upstream commit b6a5068854cfe372da7dee3224dcf023ed5b00cb ]

Since commit dcea997beed6 ("faddr2line: Fix overlapping text section
failures, the sequel"), faddr2line is completely broken on arm64.

For some reason, on arm64, the vmlinux ELF object file type is ET_DYN
rather than ET_EXEC.  Check for both when determining whether the object
is vmlinux.

Modules and vmlinux.o have type ET_REL on all arches.

Fixes: dcea997beed6 ("faddr2line: Fix overlapping text section failures, the sequel")
Reported-by: John Garry <john.garry@huawei.com>
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Tested-by: John Garry <john.garry@huawei.com>
Link: https://lore.kernel.org/r/dad1999737471b06d6188ce4cdb11329aa41682c.1658426357.git.jpoimboe@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>

genelf: Use HAVE_LIBCRYPTO_SUPPORT, not the never defined HAVE_LIBCRYPTO

[ Upstream commit 91cea6be90e436c55cde8770a15e4dac9d3032d0 ]

When genelf was introduced it tested for HAVE_LIBCRYPTO not
HAVE_LIBCRYPTO_SUPPORT, which is the define the feature test for openssl
defines, fix it.

This also adds disables the deprecation warning, someone has to fix this
to build with openssl 3.0 before the warning becomes a hard error.

Fixes: 9b07e27f88b9cd78 ("perf inject: Add jitdump mmap injection support")
Reported-by: 谭梓煊 <tanzixuan.me@gmail.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Andrii Nakryiko <andrii@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: John Fastabend <john.fastabend@gmail.com>
Cc: KP Singh <kpsingh@kernel.org>
Cc: Martin KaFai Lau <kafai@fb.com>
Cc: Nick Terrell <terrelln@fb.com>
Cc: Song Liu <songliubraving@fb.com>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lore.kernel.org/lkml/YulpPqXSOG0Q4J1o@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

powerpc/pci: Fix PHB numbering when using opal-phbid

[ Upstream commit f4b39e88b42d13366b831270306326b5c20971ca ]

The recent change to the PHB numbering logic has a logic error in the
handling of "ibm,opal-phbid".

When an "ibm,opal-phbid" property is present, &prop is written to and
ret is set to zero.

The following call to of_alias_get_id() is skipped because ret == 0.

But then the if (ret >= 0) is true, and the body of that if statement
sets prop = ret which throws away the value that was just read from
"ibm,opal-phbid".

Fix the logic by only doing the ret >= 0 check in the of_alias_get_id()
case.

Fixes: 0fe1e96fef0a ("powerpc/pci: Prefer PCI domain assignment via DT 'linux,pci-domain' and alias")
Reviewed-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220802105723.1055178-1-mpe@ellerman.id.au
Signed-off-by: Sasha Levin <sashal@kernel.org>

x86/bus_lock: Don't assume the init value of DEBUGCTLMSR.BUS_LOCK_DETECT to be zero

[ Upstream commit ffa6482e461ff550325356ae705b79e256702ea9 ]

It's possible that this kernel has been kexec'd from a kernel that
enabled bus lock detection, or (hypothetically) BIOS/firmware has set
DEBUGCTLMSR_BUS_LOCK_DETECT.

Disable bus lock detection explicitly if not wanted.

Fixes: ebb1064e7c2e ("x86/traps: Handle #DB for bus lock")
Signed-off-by: Chenyi Qiang <chenyi.qiang@intel.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Link: https://lore.kernel.org/r/20220802033206.21333-1-chenyi.qiang@intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

kprobes: Forbid probing on trampoline and BPF code areas

[ Upstream commit 28f6c37a2910f565b4f5960df52b2eccae28c891 ]

kernel_text_address() treats ftrace_trampoline, kprobe_insn_slot
and bpf_text_address as valid kprobe addresses - which is not ideal.

These text areas are removable and changeable without any notification
to kprobes, and probing on them can trigger unexpected behavior:

  https://lkml.org/lkml/2022/7/26/1148

Considering that jump_label and static_call text are already
forbiden to probe, kernel_text_address() should be replaced with
core_kernel_text() and is_module_text_address() to check other text
areas which are unsafe to kprobe.

[ mingo: Rewrote the changelog. ]

Fixes: 5b485629ba0d ("kprobes, extable: Identify kprobes trampolines as kernel text area")
Fixes: 74451e66d516 ("bpf: make jited programs visible in traces")
Signed-off-by: Chen Zhongjin <chenzhongjin@huawei.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Link: https://lore.kernel.org/r/20220801033719.228248-1-chenzhongjin@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

perf symbol: Fail to read phdr workaround

[ Upstream commit 6d518ac7be6223811ab947897273b1bbef846180 ]

The perf jvmti agent doesn't create program headers, in this case
fallback on section headers as happened previously.

Committer notes:

To test this, from a public post by Ian:

1) download a Java workload dacapo-9.12-MR1-bach.jar from
https://sourceforge.net/projects/dacapobench/

2) build perf such as "make -C tools/perf O=/tmp/perf NO_LIBBFD=1" it
should detect Java and create /tmp/perf/libperf-jvmti.so

3) run perf with the jvmti agent:

  perf record -k 1 java -agentpath:/tmp/perf/libperf-jvmti.so -jar dacapo-9.12-MR1-bach.jar -n 10 fop

4) run perf inject:

  perf inject -i perf.data -o perf-injected.data -j

5) run perf report

  perf report -i perf-injected.data | grep org.apache.fop

With this patch reverted I see lots of symbols like:

     0.00%  java             jitted-388040-4656.so  [.] org.apache.fop.fo.FObj.bind(org.apache.fop.fo.PropertyList)

With the patch (2d86612aacb7805f ("perf symbol: Correct address for bss
symbols")) I see lots of:

  dso__load_sym_internal: failed to find program header for symbol:
  Lorg/apache/fop/fo/FObj;bind(Lorg/apache/fop/fo/PropertyList;)V
  st_value: 0x40

Fixes: 2d86612aacb7805f ("perf symbol: Correct address for bss symbols")
Reviewed-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Ian Rogers <irogers@google.com>
Tested-by: Leo Yan <leo.yan@linaro.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Leo Yan <leo.yan@linaro.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lore.kernel.org/lkml/20220731164923.691193-1-irogers@google.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

powerpc/cell/axon_msi: Fix refcount leak in setup_msi_msg_address

[ Upstream commit df5d4b616ee76abc97e5bd348e22659c2b095b1c ]

of_get_next_parent() returns a node pointer with refcount incremented,
we should use of_node_put() on it when not need anymore.
Add missing of_node_put() in the error path to avoid refcount leak.

Fixes: ce21b3c9648a ("[CELL] add support for MSI on Axon-based Cell systems")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220605065129.63906-1-linmq006@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

powerpc/xive: Fix refcount leak in xive_get_max_prio

[ Upstream commit 255b650cbec6849443ce2e0cdd187fd5e61c218c ]

of_find_node_by_path() returns a node pointer with
refcount incremented, we should use of_node_put() on it when done.
Add missing of_node_put() to avoid refcount leak.

Fixes: eac1e731b59e ("powerpc/xive: guest exploitation of the XIVE interrupt controller")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220605053225.56125-1-linmq006@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

powerpc/spufs: Fix refcount leak in spufs_init_isolated_loader

[ Upstream commit 6ac059dacffa8ab2f7798f20e4bd3333890c541c ]

of_find_node_by_path() returns remote device nodepointer with
refcount incremented, we should use of_node_put() on it when done.
Add missing of_node_put() to avoid refcount leak.

Fixes: 0afacde3df4c ("[POWERPC] spufs: allow isolated mode apps by starting the SPE loader")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220603121543.22884-1-linmq006@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

f2fs: fix to remove F2FS_COMPR_FL and tag F2FS_NOCOMP_FL at the same time

[ Upstream commit 8ee236dcaa690d09ca612622e8bc8d09c302021d ]

If the inode has the compress flag, it will fail to use
'chattr -c +m' to remove its compress flag and tag no compress flag.
However, the same command will be successful when executed again,
as shown below:

  $ touch foo.txt
  $ chattr +c foo.txt
  $ chattr -c +m foo.txt
  chattr: Invalid argument while setting flags on foo.txt
  $ chattr -c +m foo.txt
  $ f2fs_io getflags foo.txt
  get a flag on foo.txt ret=0, flags=nocompression,inline_data

Fix this by removing some checks in f2fs_setflags_common()
that do not affect the original logic. I go through all the
possible scenarios, and the results are as follows. Bold is
the only thing that has changed.

+---------------+-----------+-----------+----------+
|               |            file flags            |
+ command       +-----------+-----------+----------+
|               | no flag   | compr     | nocompr  |
+---------------+-----------+-----------+----------+
| chattr +c     | compr     | compr     | -EINVAL  |
| chattr -c     | no flag   | no flag   | nocompr  |
| chattr +m     | nocompr   | -EINVAL   | nocompr  |
| chattr -m     | no flag   | compr     | no flag  |
| chattr +c +m  | -EINVAL   | -EINVAL   | -EINVAL  |
| chattr +c -m  | compr     | compr     | compr    |
| chattr -c +m  | nocompr   | *nocompr* | nocompr  |
| chattr -c -m  | no flag   | no flag   | no flag  |
+---------------+-----------+-----------+----------+

Link: https://lore.kernel.org/linux-f2fs-devel/20220621064833.1079383-1-chaoliu719@gmail.com/
Fixes: 4c8ff7095bef ("f2fs: support data compression")
Reviewed-by: Chao Yu <chao@kernel.org>
Signed-off-by: Chao Liu <liuchao@coolpad.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

s390/smp: enforce lowcore protection on CPU restart

[ Upstream commit 6f5c672d17f583b081e283927f5040f726c54598 ]

As result of commit 915fea04f932 ("s390/smp: enable DAT before
CPU restart callback is called") the low-address protection bit
gets mistakenly unset in control register 0 save area of the
absolute zero memory. That area is used when manual PSW restart
happened to hit an offline CPU. In this case the low-address
protection for that CPU will be dropped.

Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Fixes: 915fea04f932 ("s390/smp: enable DAT before CPU restart callback is called")
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

s390/maccess: rework absolute lowcore accessors

[ Upstream commit ed0192bc644f3553d64a5cb461bdd0b1fbae3fdf ]

Macro mem_assign_absolute() is able to access the whole memory, but
is only used and makes sense when updating the absolute lowcore.
Instead, introduce get_abs_lowcore() and put_abs_lowcore() macros
that limit access to absolute lowcore addresses only.

Suggested-by: Heiko Carstens <hca@linux.ibm.com>
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

s390/smp: cleanup control register update routines

[ Upstream commit 9097fc793f74ef9c677f8c4aed0c24f6f07f0133 ]

Get rid of duplicate code and redundant data.

Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

s390/smp: cleanup target CPU callback starting

[ Upstream commit dc2ab23b992c9d5dab93b9bf01b10b10465e537e ]

Macro mem_assign_absolute() is used to initialize a target
CPU lowcore callback parameters. But despite the macro name
it writes to the absolute lowcore only if the target CPU is
offline. In case the CPU is online the macro does implicitly
write to the normal memory.

That behaviour is correct, but extremely subtle. Sacrifice
few program bits in favour of clarity and distinguish between
online vs offline CPUs and normal vs absolute lowcore pointer.

Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

s390/dump: fix os_info virtual vs physical address confusion

[ Upstream commit 9de209c7d584d6e06ad92f120d83d4f27c200497 ]

Due to historical reasons os_info handling functions misuse
the notion of physical vs virtual addresses difference.

Note: this does not fix a bug currently, since virtual
and physical addresses are identical.

Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

tty: serial: fsl_lpuart: correct the count of break characters

[ Upstream commit 707f816f25590c20e056b3bd4a17ce69b03fe856 ]

The LPUART can't distinguish between a break signal and a framing error,
so need to count the break characters if there is a framing error and
received data is zero instead of the parity error.

Fixes: 5541a9bacfe5 ("serial: fsl_lpuart: handle break and make sysrq work")
Reviewed-by: Michael Walle <michael@walle.cc>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20220725050115.12396-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

powerpc/pci: Prefer PCI domain assignment via DT 'linux,pci-domain' and alias

[ Upstream commit 0fe1e96fef0a5c53b4c0d1500d356f3906000f81 ]

Other Linux architectures use DT property 'linux,pci-domain' for
specifying fixed PCI domain of PCI controller specified in Device-Tree.

And lot of Freescale powerpc boards have defined numbered pci alias in
Device-Tree for every PCIe controller which number specify preferred PCI
domain.

So prefer usage of DT property 'linux,pci-domain' (via function
of_get_pci_domain_nr()) and DT pci alias (via function
of_alias_get_id()) on powerpc architecture for assigning PCI domain to
PCI controller.

Fixes: 63a72284b159 ("powerpc/pci: Assign fixed PHB number based on device-tree properties")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220706102148.5060-2-pali@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>

powerpc/iommu: Fix iommu_table_in_use for a small default DMA window case

[ Upstream commit d80f6de9d601c30b53c17f00cb7cfe3169f2ddad ]

The existing iommu_table_in_use() helper checks if the kernel is using
any of TCEs. There are some reserved TCEs:
1) the very first one if DMA window starts from 0 to avoid having a zero
but still valid DMA handle;
2) it_reserved_start..it_reserved_end to exclude MMIO32 window in case
the default window spans across that - this is the default for the first
DMA window on PowerNV.

When 1) is the case and 2) is not the helper does not skip 1) and returns
wrong status.

This only seems occurring when passing through a PCI device to a nested
guest (not something we support really well) so it has not been seen
before.

This fixes the bug by adding a special case for no MMIO32 reservation.

Fixes: 3c33066a2190 ("powerpc/kernel/iommu: Add new iommu_table_in_use() helper")
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220714081119.3714605-1-aik@ozlabs.ru
Signed-off-by: Sasha Levin <sashal@kernel.org>

powerpc/32: Do not allow selection of e5500 or e6500 CPUs on PPC32

[ Upstream commit 9be013b2a9ecb29b5168e4b9db0e48ed53acf37c ]

Commit 0e00a8c9fd92 ("powerpc: Allow CPU selection also on PPC32")
enlarged the CPU selection logic to PPC32 by removing depend to
PPC64, and failed to restrict that depend to E5500_CPU and E6500_CPU.
Fortunately that got unnoticed because -mcpu=8540 will override the
-mcpu=e500mc64 or -mpcu=e6500 as they are ealier, but that's
fragile and may no be right in the future.

Add back the depend PPC64 on E5500_CPU and E6500_CPU.

Fixes: 0e00a8c9fd92 ("powerpc: Allow CPU selection also on PPC32")
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/8abab4888da69ff78b73a56f64d9678a7bf684e9.1657549153.git.christophe.leroy@csgroup.eu
Signed-off-by: Sasha Levin <sashal@kernel.org>

powerpc/32: Call mmu_mark_initmem_nx() regardless of data block mapping.

[ Upstream commit 980bbf7ca72012d317617fcdbfabe8708e4cef29 ]

mark_initmem_nx() calls either mmu_mark_initmem_nx() or
set_memory_attr() based on return from v_block_mapped()
of _sinittext.

But we can now handle text and data independently, so that
text may be mapped by block even when data is mapped by pages.

On the 8xx for instance, at startup 32Mbytes of memory are
pinned in TLB. So the pinned entries need to go away for sinittext.

In next patch a BAT will be set to also covers sinittext on book3s/32.
So it will also be needed to call mmu_mark_initmem_nx() even when
data above sinittext is not mapped with BATs.

As this is highly dependent on the platform, call mmu_mark_initmem_nx()
regardless of data block mapping. Then the platform will know what to
do.

Modify 8xx mmu_mark_initmem_nx() so that inittext mapping is modified
only when pagealloc debug and kfence are not active, otherwise inittext
is mapped with standard pages. And don't do anything on kernel text
which is already mapped with PAGE_KERNEL_TEXT.

Fixes: da1adea07576 ("powerpc/8xx: Allow STRICT_KERNEL_RwX with pinned TLB")
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/db3fc14f3bfa6215b0786ef58a6e2bc1e1f964d7.1655202804.git.christophe.leroy@csgroup.eu
Signed-off-by: Sasha Levin <sashal@kernel.org>

ASoC: mchp-spdifrx: disable end of block interrupt on failures

[ Upstream commit 768ac4f12ca0fda935f58eb8c5120e9d795bc6e3 ]

Disable end of block interrupt in case of wait for completion timeout
or errors to undo previously enable operation (done in
mchp_spdifrx_isr_blockend_en()). Otherwise we can end up with an
unbalanced reference counter for this interrupt.

Fixes: ef265c55c1ac ("ASoC: mchp-spdifrx: add driver for SPDIF RX")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220727090814.2446111-2-claudiu.beznea@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

video: fbdev: sis: fix typos in SiS_GetModeID()

[ Upstream commit 3eb8fccc244bfb41a7961969e4db280d44911226 ]

The second operand of a '&&' operator has no impact on expression
result for cases 400 and 512 in SiS_GetModeID().

Judging by the logic and the names of the variables, in both cases a
typo was made.

Found by Linux Verification Center (linuxtesting.org) with SVACE.

Signed-off-by: Rustam Subkhankulov <subkhankulov@ispras.ru>
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

video: fbdev: amba-clcd: Fix refcount leak bugs

[ Upstream commit 26c2b7d9fac42eb8317f3ceefa4c1a9a9170ca69 ]

In clcdfb_of_init_display(), we should call of_node_put() for the
references returned by of_graph_get_next_endpoint() and
of_graph_get_remote_port_parent() which have increased the refcount.

Besides, we should call of_node_put() both in fail path or when
the references are not used anymore.

Fixes: d10715be03bd ("video: ARM CLCD: Add DT support")
Signed-off-by: Liang He <windhl@126.com>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

watchdog: armada_37xx_wdt: check the return value of devm_ioremap() in armada_37xx_wdt_probe()

[ Upstream commit 2d27e52841092e5831dd41f313028c668d816eb0 ]

The function devm_ioremap() in armada_37xx_wdt_probe() can fail, so
its return value should be checked.

Fixes: 54e3d9b518c8a ("watchdog: Add support for Armada 37xx CPU watchdog")
Reported-by: Hacash Robot <hacashRobot@santino.com>
Signed-off-by: William Dean <williamsukatube@gmail.com>
Reviewed-by: Marek Beh=C3=BAn <kabel@kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220722030938.2925156-1-williamsukatube@163.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

watchdog: sp5100_tco: Fix a memory leak of EFCH MMIO resource

[ Upstream commit c6d9c0798ed366a09a9e53d71edcd2266e34a6eb ]

Unlike release_mem_region(), a call to release_resource() does not
free the resource, so it has to be freed explicitly to avoid a memory
leak.

Signed-off-by: Jean Delvare <jdelvare@suse.de>
Fixes: 0578fff4aae5 ("Watchdog: sp5100_tco: Add initialization using EFCH MMIO")
Cc: Terry Bowman <terry.bowman@amd.com>
Cc: Wim Van Sebroeck <wim@linux-watchdog.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220621152840.420a0f4c@endymion.delvare
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ASoC: audio-graph-card: Add of_node_put() in fail path

[ Upstream commit 65fb8e2ef3531a6e950060fca6e551c923fb0f0e ]

In asoc_simple_parse_dai(), we should call of_node_put() for the
reference returned by of_graph_get_port_parent() in fail path.

Fixes: ae30a694da4c ("ASoC: simple-card-utils: add asoc_simple_card_parse_dai()")
Signed-off-by: Liang He <windhl@126.com>
Link: https://lore.kernel.org/r/20220721144308.1301587-1-windhl@126.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

fuse: Remove the control interface for virtio-fs

[ Upstream commit c64797809a64c73497082aa05e401a062ec1af34 ]

The commit 15c8e72e88e0 ("fuse: allow skipping control interface and forced
unmount") tries to remove the control interface for virtio-fs since it does
not support aborting requests which are being processed. But it doesn't
work now.

This patch fixes it by skipping creating the control interface if
fuse_conn->no_control is set.

Fixes: 15c8e72e88e0 ("fuse: allow skipping control interface and forced unmount")
Signed-off-by: Xie Yongji <xieyongji@bytedance.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ASoC: qcom: q6dsp: Fix an off-by-one in q6adm_alloc_copp()

[ Upstream commit 673f58f62ca6fc98979d1cf3fe89c3ff33f29b2e ]

find_first_zero_bit() returns MAX_COPPS_PER_PORT at max here.
So 'idx' should be tested with ">=" or the test can't match.

Fixes: 7b20b2be51e1 ("ASoC: qdsp6: q6adm: Add q6adm driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/0fca3271649736053eb9649d87e1ca01b056be40.1658394124.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ASoC: imx-card: use snd_pcm_format_t type for asrc_format

[ Upstream commit 409a8652e909e323c715f3088e6c3133e37c8881 ]

Fix sparse warning:
sound/soc/fsl/imx-card.c:653:59: sparse: warning: incorrect type in assignment (different base types)
sound/soc/fsl/imx-card.c:653:59: sparse:    expected unsigned int [usertype] asrc_format
sound/soc/fsl/imx-card.c:653:59: sparse:    got restricted snd_pcm_format_t [usertype]
sound/soc/fsl/imx-card.c:655:59: sparse: warning: incorrect type in assignment (different base types)
sound/soc/fsl/imx-card.c:655:59: sparse:    expected unsigned int [usertype] asrc_format
sound/soc/fsl/imx-card.c:655:59: sparse:    got restricted snd_pcm_format_t [usertype]

Fixes: aa736700f42f ("ASoC: imx-card: Add imx-card machine driver")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1658399393-28777-6-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ASoC: fsl_easrc: use snd_pcm_format_t type for sample_format

[ Upstream commit de27216cf2d645c2fd14e513707bdcd54e5b1de4 ]

Fix sparse warning:
sound/soc/fsl/fsl_easrc.c:562:33: sparse: warning: restricted snd_pcm_format_t degrades to integer
sound/soc/fsl/fsl_easrc.c:563:34: sparse: warning: restricted snd_pcm_format_t degrades to integer
sound/soc/fsl/fsl_easrc.c:565:38: sparse: warning: restricted snd_pcm_format_t degrades to integer
sound/soc/fsl/fsl_easrc.c:566:39: sparse: warning: restricted snd_pcm_format_t degrades to integer
sound/soc/fsl/fsl_easrc.c:608:33: sparse: warning: restricted snd_pcm_format_t degrades to integer
sound/soc/fsl/fsl_easrc.c:609:34: sparse: warning: restricted snd_pcm_format_t degrades to integer
sound/soc/fsl/fsl_easrc.c:615:40: sparse: warning: restricted snd_pcm_format_t degrades to integer
sound/soc/fsl/fsl_easrc.c:616:41: sparse: warning: restricted snd_pcm_format_t degrades to integer

sound/soc/fsl/fsl_easrc.c:1465:51: sparse: warning: incorrect type in assignment (different base types)
sound/soc/fsl/fsl_easrc.c:1465:51: sparse:    expected unsigned int sample_format
sound/soc/fsl/fsl_easrc.c:1465:51: sparse:    got restricted snd_pcm_format_t [usertype] format
sound/soc/fsl/fsl_easrc.c:1467:52: sparse: warning: incorrect type in assignment (different base types)
sound/soc/fsl/fsl_easrc.c:1467:52: sparse:    expected unsigned int sample_format
sound/soc/fsl/fsl_easrc.c:1467:52: sparse:    got restricted snd_pcm_format_t [usertype] asrc_format
sound/soc/fsl/fsl_easrc.c:1470:52: sparse: warning: incorrect type in assignment (different base types)
sound/soc/fsl/fsl_easrc.c:1470:52: sparse:    expected unsigned int sample_format
sound/soc/fsl/fsl_easrc.c:1470:52: sparse:    got restricted snd_pcm_format_t [usertype] format
sound/soc/fsl/fsl_easrc.c:1472:51: sparse: warning: incorrect type in assignment (different base types)
sound/soc/fsl/fsl_easrc.c:1472:51: sparse:    expected unsigned int sample_format
sound/soc/fsl/fsl_easrc.c:1472:51: sparse:    got restricted snd_pcm_format_t [usertype] asrc_format
sound/soc/fsl/fsl_easrc.c:1484:41: sparse: warning: incorrect type in argument 2 (different base types)
sound/soc/fsl/fsl_easrc.c:1484:41: sparse:    expected restricted snd_pcm_format_t [usertype] *in_raw_format
sound/soc/fsl/fsl_easrc.c:1484:41: sparse:    got unsigned int *
sound/soc/fsl/fsl_easrc.c:1485:41: sparse: warning: incorrect type in argument 3 (different base types)
sound/soc/fsl/fsl_easrc.c:1485:41: sparse:    expected restricted snd_pcm_format_t [usertype] *out_raw_format
sound/soc/fsl/fsl_easrc.c:1485:41: sparse:    got unsigned int *
sound/soc/fsl/fsl_easrc.c:1937:60: sparse: warning: incorrect type in argument 3 (different base types)
sound/soc/fsl/fsl_easrc.c:1937:60: sparse:    expected unsigned int [usertype] *out_value
sound/soc/fsl/fsl_easrc.c:1937:60: sparse:    got restricted snd_pcm_format_t *
sound/soc/fsl/fsl_easrc.c:1943:49: sparse: warning: restricted snd_pcm_format_t degrades to integer

Fixes: 955ac624058f ("ASoC: fsl_easrc: Add EASRC ASoC CPU DAI drivers")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1658399393-28777-5-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ASoC: fsl-asoc-card: force cast the asrc_format type

[ Upstream commit 6c7b077dad62178c33f9a3ae17f90d6b0bf6e2e5 ]

Fix sparse warning:
sound/soc/fsl/fsl-asoc-card.c:833:45: sparse: warning: incorrect type in argument 3 (different base types)
sound/soc/fsl/fsl-asoc-card.c:833:45: sparse:    expected unsigned int [usertype] *out_value
sound/soc/fsl/fsl-asoc-card.c:833:45: sparse:    got restricted snd_pcm_format_t *

Fixes: 859e364302c5 ("ASoC: fsl-asoc-card: Support new property fsl, asrc-format")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1658399393-28777-4-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ASoC: fsl_asrc: force cast the asrc_format type

[ Upstream commit c49932726de24405d45516b3f8ad2735714fdf05 ]

Fix sparse warning:
sound/soc/fsl/fsl_asrc.c:1177:60: sparse: warning: incorrect type in argument 3 (different base types)
sound/soc/fsl/fsl_asrc.c:1177:60: sparse:    expected unsigned int [usertype] *out_value
sound/soc/fsl/fsl_asrc.c:1177:60: sparse:    got restricted snd_pcm_format_t *
sound/soc/fsl/fsl_asrc.c:1200:47: sparse: warning: restricted snd_pcm_format_t degrades to integer

Fixes: 4520af41fd21 ("ASoC: fsl_asrc: Support new property fsl,asrc-format")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1658399393-28777-3-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

s390/zcore: fix race when reading from hardware system area

[ Upstream commit 9ffed254d938c9e99eb7761c7f739294c84e0367 ]

Memory buffer used for reading out data from hardware system
area is not protected against concurrent access.

Reported-by: Matthew Wilcox <willy@infradead.org>
Fixes: 411ed3225733 ("[S390] zfcpdump support.")
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Tested-by: Alexander Egorenkov <egorenar@linux.ibm.com>
Link: https://lore.kernel.org/r/e68137f0f9a0d2558f37becc20af18e2939934f6.1658206891.git.agordeev@linux.ibm.com
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

s390/crash: fix incorrect number of bytes to copy to user space

[ Upstream commit f6749da17a34eb08c9665f072ce7c812ff68aad2 ]

The number of bytes in a chunk is correctly calculated, but instead
the total number of bytes is passed to copy_to_user_real() function.

Reported-by: Matthew Wilcox <willy@infradead.org>
Fixes: df9694c7975f ("s390/dump: streamline oldmem copy functions")
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

s390/maccess: fix semantics of memcpy_real() and its callers

[ Upstream commit 303fd988ed644c7daa260410f3ac99266573557d ]

There is a confusion with regard to the source address of
memcpy_real() and calling functions. While the declared
type for a source assumes a virtual address, in fact it
always called with physical address of the source.

This confusion led to bugs in copy_oldmem_kernel() and
copy_oldmem_user() functions, where __pa() macro applied
mistakenly to physical addresses. It does not lead to a
real issue, since virtual and physical addresses are
currently the same.

Fix both the bugs and memcpy_real() prototype by making
type of source address consistent to the function name
and the way it actually used.

Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

s390/dump: fix old lowcore virtual vs physical address confusion

[ Upstream commit dc306186a130c6d9feb0aabc1c71b8ed1674a3bf ]

Virtual addresses of vmcore_info and os_info members are
wrongly passed to copy_oldmem_kernel(), while the function
expects physical address of the source. Instead, __pa()
macro should have been applied.

Yet, use of __pa() macro could be somehow confusing, since
copy_oldmem_kernel() may treat the source as an offset, not
as a direct physical address (that depens from the oldmem
availability and location).

Fix the virtual vs physical address confusion and make the
way the old lowcore is read consistent across all sources.

Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

perf tools: Fix dso_id inode generation comparison

[ Upstream commit 68566a7cf56bf3148797c218ed45a9de078ef47c ]

Synthesized MMAP events have zero ino_generation, so do not compare
them to DSOs with a real ino_generation otherwise we end up with a DSO
without a build id.

Fixes: 0e3149f86b99ddab ("perf dso: Move dso_id from 'struct map' to 'struct dso'")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: kvm@vger.kernel.org
Cc: Namhyung Kim <namhyung@kernel.org>
Link: https://lore.kernel.org/r/20220711093218.10967-2-adrian.hunter@intel.com
[ Added clarification to the comment from Ian + more detailed explanation from Adrian ]
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>