staging: bcm2835-camera: Add sanity checks for queue_setup/CREATE_BUFS

Fixes a v4l2-compliance failure when passed a buffer that is
too small.
queue_setup wasn't handling the case where *nplanes != 0, as
used from CREATE_BUFS and requiring the driver to sanity
check the provided buffer parameters. It was assuming that
it was always being used in the REQBUFS case where it provides
the buffer properties.

Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: bcm2835-camera: Fix stride on RGB3/BGR3 formats

RGB3/BGR3 end up being 3 bytes per pixel, which meant that
the alignment code ended up trying to align using bitmasking
with a mask of 96.
That doesn't work, so switch to an arithmetic alignment for
those formats.

Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: mmal-vchiq: Avoid use of bool in structures

Fixes up a checkpatch error "Avoid using bool structure members
because of possible alignment issues".

Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: bcm2835-camera: Remove/amend some obsolete comments

Remove a todo which has been done.
Remove a template line that was redundant.
Make a comment clearer as to the non-obvious meaning of a field.

Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: bcm2835-camera: Correct V4L2_CID_COLORFX_CBCR behaviour

With V4L2_CID_COLORFX_CBCR calling ctrl_set_colfx it was incorrectly
assigning the colour values to the enable field of dev->colourfx
instead of the u and v fields.

Correct the assignments.

Reported as a Coverity issue
Detected by CoverityScan CID#1419711 ("Unused value")

Reported-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: bcm2835-camera: Use enums for max value in controls

Controls of type MMAL_CONTROL_TYPE_STD_MENU call v4l2_ctrl_new_std_menu
with a max value and a mask. The max value is one of the defined
values for the control, however in the config array there are several
entries where raw numbers have been used instead. Replace these
with the appropriate enum.

Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: bcm2835-camera: Fix up mmal-parameters.h

Fixes up all the checkpatch error "line over 80 characters" in
mmal-parameters.h

Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: bcm2835-camera: Fix multiple assignments should be avoided

Clear checkpatch complaints of "multiple assignments should be avoided"

Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: bcm2835-camera: Unify header inclusion defines

Most of the headers use ifndef FOO_H, whilst mmal-parameters.h
used ifndef __FOO_H.

Revise mmal-parameters.h to drop the underscores and make the
headers all consistent.

Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: bcm2835-camera: Add multiple inclusion protection to headers

mmal-common.h and mmal-msg.h didn't have the normal
ifndef FOO / define FOO / endif protection to stop it being
included multiple times. Add it.

Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: bcm2835-camera: Set sequence number correctly

Set the sequence number in vb2_v4l2_buffer mainly so the
latest v4l2-ctl reports the frame rate correctly.

Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: bcm2835-camera: Handle empty EOS buffers whilst streaming

The change to mapping V4L2 to MMAL buffers 1:1 didn't handle
the condition we get with raw pixel buffers (eg YUV and RGB)
direct from the camera's stills port. That sends the pixel buffer
and then an empty buffer with the EOS flag set. The EOS buffer
wasn't handled and returned an error up the stack.

Handle the condition correctly by returning it to the component
if streaming, or returning with an error if stopping streaming.

Fixes: 938416707071 ("staging: bcm2835-camera: Remove V4L2/MMAL buffer remapping")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: bcm2835-camera: Remove check of the number of buffers supplied

Before commit "staging: bcm2835-camera: Remove V4L2/MMAL buffer remapping"
there was a need to ensure that there were sufficient buffers supplied from
the user to cover those being sent to the VPU (always 1).

Now the buffers are linked 1:1 between MMAL and V4L2,
therefore there is no need for that check, and indeed it is wrong
as there is no need to submit all the buffers before starting streaming.

Fixes: 938416707071 ("staging: bcm2835-camera: Remove V4L2/MMAL buffer remapping")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: bcm2835-camera: Ensure all buffers are returned on disable

With the recent change to match MMAL and V4L2 buffers there
is a need to wait for all MMAL buffers to be returned during
stop_streaming.

Fixes: 938416707071 ("staging: bcm2835-camera: Remove V4L2/MMAL buffer remapping")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: bcm2835-camera: Fix open parenthesis alignment

Fix checkpatch "Alignment should match open parenthesis"
errors.

Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: bcm2835-camera: Fix missing lines between items

Fix checkpatch errors for missing blank lines after variable
or structure declarations.

Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: bcm2835-camera: Fix brace style issues.

Fix mismatched or missing brace issues flagged by checkpatch.

Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: bcm2835-camera: Fix multiple line dereference errors

Fix checkpatch errors "Avoid multiple line dereference"

Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: bcm2835-camera: Reduce length of enum names

We have numerous lines over 80 chars, or oddly split. Many
of these are due to using long enum names such as
MMAL_COMPONENT_CAMERA.
Reduce the length of these enum names.

Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: bcm2835-camera: Fix spacing around operators

Fix checkpatch warnings over spaces around operators.
Many were around operations that can be replaced with the
BIT(x) macro, so replace with that where appropriate.

Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: bcm2835-camera: Fix comment style violations.

Fix comment style violations in the header files.

Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: bcm2835-camera: Remove dead email addresses

None of the listed author email addresses were valid.
Keep list of authors and the companies they represented.
Update my email address.

Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: bcm2835-camera: Return early on errors

Fix several instances where it is easier to return
early on error conditions than handle it as an else
clause. As requested by Mauro.

Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: bcm2835-camera: Correctly denote key frames in encoded data

Forward MMAL key frame flags to the V4L2 buffers.

Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: bcm2835-camera: Do not bulk receive from service thread

vchi_bulk_queue_receive will queue up to a default of 4
bulk receives on a connection before blocking.
If called from the VCHI service_callback thread, then
that thread is unable to service the VCHI_CALLBACK_BULK_RECEIVED
events that would enable the queue call to succeed.

Add a workqueue to schedule the call vchi_bulk_queue_receive
in an alternate context to avoid the lock up.

Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: bcm2835-camera: Replace spinlock protecting context_map with mutex

The commit "staging: bcm2835-camera: Replace open-coded idr with a struct idr."
replaced an internal implementation of an idr with the standard functions
and a spinlock. idr_alloc(GFP_KERNEL) can sleep whilst calling kmem_cache_alloc
to allocate the new node, but this is not valid whilst in an atomic context
due to the spinlock.

There is no need for this to be a spinlock as a standard mutex is
sufficient.

Fixes: 950fd867c635 ("staging: bcm2835-camera: Replace open-coded idr with a struct idr.")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: bcm2835-camera: Check the error for REPEAT_SEQ_HEADER

When handling for V4L2_CID_MPEG_VIDEO_REPEAT_SEQ_HEADER was added
the firmware would reject the setting if H264 hadn't already been
selected. This was fixed in the firmware at that point, but to
enable backwards compatibility the returned error was ignored.

That was Dec 2013, so the chances of having a firmware that still
has that issue is so close to zero that the workaround can be
removed.

Link: https://github.com/raspberrypi/linux/pull/2782/
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging/rtl8188eu/os_dep: Remove unneeded variable ret

Below list of functions returns 0 in success and -EINVAL in failure. So
directly return 0 on Success.

Signed-off-by: Hariprasad Kelam <hariprasad.kelam@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8188eu: Remove declarations of unused functions

Remove the declarations of the following unused functions from
rtw_eeprom.h:
- eeprom_write16
- eeprom_read16
- eeprom_read_sz
- read_eeprom_content
- read_eeprom_content_by_attrib.

Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8188eu: hal: Replace function ODM_TXPowerTrackingCheck()

Remove function ODM_TXPowerTrackingCheck as all it does is call
odm_TXPowerTrackingCheckCE.
Rename odm_TXPowerTrackingCheckCE to ODM_TXPowerTrackingCheck for
compatibility with call sites.
Issue found with Coccinelle.

Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8188eu: hal: Replace function odm_TXPowerTrackingInit()

Remove function odm_TXPowerTrackingInit as all it does is call
odm_TXPowerTrackingThermalMeterInit.
Rename odm_TXPowerTrackingThermalMeterInit to odm_TXPowerTrackingInit
for compatibility with call sites.
Issue found with Coccinelle.

Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8188eu: os_dep: Remove return variable

Remove return variable as its value is not altered between
initialisation and return.
Issue found with Coccinelle.

Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: netlogic: Change GFP_ATOMIC to GFP_KERNEL

Below is data path of xlr_config_spill
xlr_net_probe
  -->xlr_config_fifo_spill_area
  --->xlr_config_spill

We can use GFP_KERNEL as this function is getting called from
xlr_net_probe and there are no locks.

Signed-off-by: Hariprasad Kelam <hariprasad.kelam@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rts5208: Simplify boolean expression to improve code style

This bitwisen / boolean expression can be made more readable while
reducing the line lengths at the same time. This commit uses the
fact that

    a & (b | c) == (b | c)

evaluates to true if and only if

    (a & b) && (a & c)

is true. Since b and c are constants with relatively long names,
using the second form makes the code much more readable and shorter.

Signed-off-by: Tobias Nießen <tobias.niessen@stud.uni-hannover.de>
Signed-off-by: Sabrina Gaube <sabrina-gaube@web.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rts5208: Rewrite redundant if statement to improve code style

This commit uses the fact that

    if (a) {
            if (b) {
                    ...
            }
    }

can instead be written as

    if (a && b) {
            ...
    }

without any change in behavior, allowing to decrease the indentation
of the contained code block and thus reducing the average line length.

Signed-off-by: Tobias Nießen <tobias.niessen@stud.uni-hannover.de>
Signed-off-by: Sabrina Gaube <sabrina-gaube@web.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: wilc1000: rename 'host_interface' source and header

Rename 'host_interface' source and header file to include the 'wilc_'
prefix in its name.

Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: wilc1000: remove extra argument passing to wilc_send_config_pkt()

Cleanup patch to remove the passing of driver handler, get the 'idx'
value inside the called function.

Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: wilc1000: remove use of 'src_addr' element in 'wilc_vif' struct

Remove use of 'src_addr' element in wilc_vif, as the same information
already copied to net_device->dev_addr.

Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: wilc1000: remove unnecessary loop to traverse vif interfaces

Cleanup patch to avoid loop to traverse the interfaces instead make use
of vif received from net_device priv data.

Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: wilc1000: remove use of driver_handler_id & ifc_id

Removed the 'driver_handler_id' & 'ifc_id' elements and used 'idx' to
identify the handler.

Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: wilc1000: added support to dynamically add/remove interfaces

Removed the use of two hardcoded interfaces and added support to
add/remove the network interfaces dynamically.
Now the driver will have single default interface with name 'wlan0' and
later other interface can be added from user space application e.g
using 'iw add' command.
Also taken care to maintain 'wilc_vif' as part of 'net_device'
private data and 'wilc' struct as 'wiphy' private data.

Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: wilc1000: fix error path cleanup in wilc_wlan_initialize()

For the error path in wilc_wlan_initialize(), the resources are not
cleanup in the correct order. Reverted the previous changes and use the
correct order to free during error condition.

Fixes: b46d68825c2d ("staging: wilc1000: remove COMPLEMENT_BOOT")
Cc: <stable@vger.kernel.org>
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: wilc1000: handle p2p operations in caller context

Moved the handling of p2p related operation in the caller context instead
of using workqueue.

Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8188eu: Add 'rtl8188eufw.bin' to MODULE_FIRMWARE list

This is the file loaded by the code anyway, but now you can use
'modinfo' to determine the needed firmware file for this module.

Spotted when packaging firmware files for the fli4l Linux router
distribution, where a script uses the information from 'modinfo' to
collect all needed firmware files to package.

Cc: Christoph Schulz <mail@kristov.de>
Signed-off-by: Alexander Dahl <post@lespocky.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: mt7621-pci: fix PCIE_FTS_NUM_LO macro

Add missing parenthesis to PCIE_FTS_NUM_LO macro to do the
same it was being done in original code.

Fixes: a4b2eb912bb1 ("staging: mt7621-pci: rewrite RC FTS configuration")
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: bcm2835-camera: Restore return behavior of ctrl_set_bitrate()

The commit 52c4dfcead49 ("Staging: vc04_services: Cleanup in
ctrl_set_bitrate()") changed the return behavior of ctrl_set_bitrate().
We cannot do this because of a bug in the firmware, which breaks probing
of bcm2835-camera:

    bcm2835-v4l2: mmal_init: failed to set all camera controls: -3
    Cleanup: Destroy video encoder
    Cleanup: Destroy image encoder
    Cleanup: Destroy video render
    Cleanup: Destroy camera
    bcm2835-v4l2: bcm2835_mmal_probe: mmal init failed: -3
    bcm2835-camera: probe of bcm2835-camera failed with error -3

So restore the old behavior, add an explaining comment and a debug message
to verify that the bug has been fixed in firmware.

Fixes: 52c4dfcead49 ("Staging: vc04_services: Cleanup in ctrl_set_bitrate()")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Cc: stable <stable@vger.kernel.org>
Acked-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: greybus: tools: Remove function log_csv_error()

Remove unused function log_csv_error.
Issue found with Coccinelle.

Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Reviewed-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: comedi: dt282x: fix a null pointer deref on interrupt

The interrupt handler `dt282x_interrupt()` causes a null pointer
dereference for those supported boards that have no analog output
support.  For these boards, `dev->write_subdev` will be `NULL` and
therefore the `s_ao` subdevice pointer variable will be `NULL`.  In that
case, the following call near the end of the interrupt handler results
in a null pointer dereference:

comedi_handle_events(dev, s_ao);

Fix it by only calling the above function if `s_ao` is valid.

(There are other uses of `s_ao` by the interrupt handler that may or may
not be reached depending on values of hardware registers.  Trust that
they are reliable for now.)

Note:
commit 4f6f009b204f ("staging: comedi: dt282x: use comedi_handle_events()")
propagates an earlier error from
commit f21c74fa4cfe ("staging: comedi: dt282x: use cfc_handle_events()").

Fixes: 4f6f009b204f ("staging: comedi: dt282x: use comedi_handle_events()")
Cc: <stable@vger.kernel.org> # v3.19+
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: comedi: amplc_pci230: fix null pointer deref on interrupt

The interrupt handler `pci230_interrupt()` causes a null pointer
dereference for a PCI260 card.  There is no analog output subdevice for
a PCI260.  The `dev->write_subdev` subdevice pointer and therefore the
`s_ao` subdevice pointer variable will be `NULL` for a PCI260.  The
following call near the end of the interrupt handler results in the null
pointer dereference for a PCI260:

comedi_handle_events(dev, s_ao);

Fix it by only calling the above function if `s_ao` is valid.

Note that the other uses of `s_ao` in the calls
`pci230_handle_ao_nofifo(dev, s_ao);` and `pci230_handle_ao_fifo(dev,
s_ao);` will never be reached for a PCI260, so they are safe.

Fixes: 39064f23284c ("staging: comedi: amplc_pci230: use comedi_handle_events()")
Cc: <stable@vger.kernel.org> # v3.19+
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging/most/video: set device_caps in struct video_device

Instead of filling in the struct v4l2_capability device_caps
field, fill in the struct video_device device_caps field.

That way the V4L2 core knows what the capabilities of the
video device are.

Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: erofs: Replace kzalloc(struct ..) with kzalloc(*ptr)

Resolve checkpatch warning:
Prefer kzalloc(sizeof(*ptr)...) over kzalloc(sizeof(struct ..)

Signed-off-by: Shobhit Kukreti <shobhitkukreti@gmail.com>
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Reviewed-by: Gao Xiang <gaoxiang25@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: erofs: don't check special inode layout

Currently, we will check if inode layout is compression or inline if
the inode is special in fill_inode(). Also set ->i_mapping->a_ops for
it. That is pointless since the both modes won't be set for special
inode when creating EROFS filesystem image. So, let's avoid it.

Signed-off-by: Yue Hu <huyue2@yulong.com>
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: erofs: return the error value if fill_inline_data() fails

We should consider the error returned by fill_inline_data() when filling
last page in fill_inode(). If not getting inode will be successful even
though last page is bad. That is illogical. Also change -EAGAIN to 0 in
fill_inline_data() to stand for successful filling.

Signed-off-by: Yue Hu <huyue2@yulong.com>
Reviewed-by: Gao Xiang <gaoxiang25@huawei.com>
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8712: reduce stack usage, again

An earlier patch I sent reduced the stack usage enough to get
below the warning limit, and I could show this was safe, but with
GCC_PLUGIN_STRUCTLEAK_BYREF_ALL, it gets worse again because large stack
variables in the same function no longer overlap:

drivers/staging/rtl8712/rtl871x_ioctl_linux.c: In function 'translate_scan.isra.2':
drivers/staging/rtl8712/rtl871x_ioctl_linux.c:322:1: error: the frame size of 1200 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]

Split out the largest two blocks in the affected function into two
separate functions and mark those noinline_for_stack.

Fixes: 8c5af16f7953 ("staging: rtl8712: reduce stack usage")
Fixes: 81a56f6dcd20 ("gcc-plugins: structleak: Generalize to all variable types")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8712: Change return values of r8712_setrfreg_cmd()

Change return values of function r8712_setrfreg_cmd from _SUCCESS/_FAIL
to 0/-ENOMEM respectively. Modify call site accordingly.

Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8712: Remove r8712_setassocsta_cmd()

Remove function r8712_setassocsta_cmd as it is only called by
mp_start_joinbss, which was removed in the previous patch.

Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8712: Remove mp_start_joinbss()

Remove unused function mp_start_joinbss.

Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8712: Replace r8712_find_network()

Remove function r8712_find_network as all it does is call
_r8712_find_network.
Rename _r8712_find_network to r8712_find_network for compatibility with
call sites.

Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8712: Remove r8712_setrttbl_cmd()

Remove unused function r8712_setrttbl_cmd.

Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8712: Replace r8712_free_evt_priv()

Remove function r8712_free_evt_priv as all it does is call
_free_evt_priv.
Rename _free_evt_priv to r8712_free_evt_priv to maintain compatibility
with call sites.
Change type of new r8712_free_evt_priv from static to non-static to
match old definition.

Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8712: Replace r8712_free_cmd_priv()

Remove function r8712_free_cmd_priv as all it does is call
_free_cmd_priv.
Change type of new r8712_free_cmd_priv from static to non-static to
match definition of original r8712_free_cmd_priv.

Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8712: Change return values of r8712_init_evt_priv()

Change return values of the function r8712_init_evt_priv from
_SUCCESS/_FAIL to 0/-ENOMEM. Modify call site accordingly.

Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8712: Replace function r8712_init_evt_priv()

Remove function r8712_init_evt_priv as all it does is call
_init_evt_priv.
Rename _init_evt_priv to r8712_init_evt_priv to maintain compatibility
with call sites.
Change type of new r8712_init_evt_priv from static to non-static as
original r8712_init_evt_priv was non-static.
Change return type of new r8712_init_evt_priv to int as original had
return type u32 but new (formerly _init_evt_priv) had return type sint.

Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8712: Change return values in r8712_init_cmd_priv()

Change return values in r8712_init_cmd_priv from _SUCCESS/_FAIL to
0/-ENOMEM. Modify call site accordingly.

Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: vc04_services: Remove function block_resume()

Remove function block_resume as it was only called by
vchiq_arm_force_suspend, which was removed in a previous patch.
Issue found with Coccinelle.

Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: vc04_services: Remove function output_timeout_error()

Remove function output_timeout_error as it was only called by
vchiq_arm_force_suspend, which was deleted in a previous patch.
Issue found with Coccinelle.

Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: vc04_services: Remove vchiq_send_remote_release()

Remove unused function vchiq_send_remote_release.
Issue found with Coccinelle.

Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: vc04_services: Remove vchiq_use_service_no_resume()

Remove unused function vchiq_use_service_no_resume.
Issue found with Coccinelle.

Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: vc04_services: Remove vchiq_resume_internal()

Remove unused function vchiq_resume_internal.
Issue found with Coccinelle.

Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: vc04_services: Remove vchiq_pause_internal()

Remove unused function vchiq_pause_internal.
Issue found with Coccinelle.

Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: vc04_services: Remove vchiq_arm_force_suspend()

Remove unused function vchiq_arm_force_suspend.
Issue found with Coccinelle.

Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: vc04_services: Remove function vchiq_arm_allow_resume()

Remove unused function vchiq_arm_allow_resume.
Issue found with Coccinelle.

Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: vc04_services: Remove function vchiu_queue_is_full()

Remove unused function vchiu_queue_is_full.
Issue found with Coccinelle.

Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: kpc2000: add missing spaces in kpc2000_spi.c

Fixes checkpatch errors:
- spaces required around that '=' (ctx:VxV)
- space required before the open parenthesis '('
- spaces preferred around that '-' (ctx:VxV)
- space required before the open brace '{'

Signed-off-by: Simon Sandström <simon@nikanor.nu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: kpc2000: add missing spaces in kpc2000_i2c.c

Fixes checkpatch "CHECK: spaces preferred around that '+' (ctx:VxV)".

Signed-off-by: Simon Sandström <simon@nikanor.nu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8188eu: remove unused function is_ap_in_wep()

Function is_ap_in_wep() is not used in the driver code, so remove it.

Signed-off-by: Michael Straube <straube.linux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8188eu: remove unused function get_bsstype()

Function get_bsstype() is not used in the driver code, so remove it.

Signed-off-by: Michael Straube <straube.linux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8723bs: os_dep: Change return type of rtw_init_default_value() to void

rtw_init_default_value() func always returns a value (u8)_SUCCESS.
Modified return type to void to resolve coccicheck warnings
of unneeded variable.

Signed-off-by: Shobhit Kukreti <shobhitkukreti@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8723bs: os_dep: modified return type of function rtw_suspend_wow() to void

Changed return type of function rtw_suspend_wow() to void.
The function always return _SUCCESS and the value is never
checked in the calling function.

Resolves coccicheck Unneeded variable "ret" warning.

Signed-off-by: Shobhit Kukreti <shobhitkukreti@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8723bs: os_dep: Change return type of function rtw_suspend_normal() to void

Coccicheck issues Unneeded variable "ret" warning.
The return value of function rtw_suspend_normal() is set to _SUCCESS.
The return value is never never checked by the calling function.
Modified return type to void to remove the coccicheck warning..

Signed-off-by: Shobhit Kukreti <shobhitkukreti@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8723bs: os_dep: Modify return type of function rtw_reset_drv_sw() to void.

The function rtw_reset_drv_sw() return value is set to _SUCCESS.
The return value is never checked when the function is called.
Modified the return value to void to remove "Unneeded Variable warning
of coccicheck.

Signed-off-by: Shobhit Kukreti <shobhitkukreti@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8723bs: os_dep: Modify return type of function loadparam(..) to void

The function static uint loadparam(struct adapter *padapter, _nic_hdl
pnetdev) return type is modified to void.
The initial return value was always returning _SUCCESS and the return value
is never checked when the function is called.
This resolves coccicheck warnings of unneeded variables.

Signed-off-by: Shobhit Kukreti <shobhitkukreti@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8188eu: remove hal_init_macaddr()

Function hal_init_macaddr() just calls rtw_hal_set_hwreg().
Use rtw_hal_set_hwreg() directly and remove hal_init_macaddr().

Signed-off-by: Michael Straube <straube.linux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8188eu: cleanup lines ending with a '('

Cleanup checkpatch issues in usb_halinit.c.
CHECK: Lines should not end with a '('

Signed-off-by: Michael Straube <straube.linux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: erofs: integrate decompression inplace

Decompressor needs to know whether it's a partial
or full decompression since only full decompression
can be decompressed in-place.

On kirin980 platform, sequential read is finally
increased to 812MiB/s after decompression inplace
is enabled.

Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Gao Xiang <gaoxiang25@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: erofs: switch to new decompression backend

This patch integrates new decompression framework to
erofs decompression path, and remove the old
decompression implementation as well.

On kirin980 platform, sequential read is slightly
improved to 778MiB/s after the new decompression
backend is used.

Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Gao Xiang <gaoxiang25@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: erofs: introduce LZ4 decompression inplace

compressed data will be usually loaded into last pages of
the extent (the last page for 4k) for in-place decompression
(more specifically, in-place IO), as ilustration below,

         start of compressed logical extent
           |                          end of this logical extent
           |                           |
     ______v___________________________v________
... |  page 6  |  page 7  |  page 8  |  page 9  | ...
    |__________|__________|__________|__________|
           .                         ^ .        ^
           .                         |compressed|
           .                         |   data   |
           .                           .        .
           |<          dstsize        >|<margin>|
                                       oend     iend
           op                        ip

Therefore, it's possible to do decompression inplace (thus no
memcpy at all) if the margin is sufficient and safe enough [1],
and it can be implemented only for fixed-size output compression
compared with fixed-size input compression.

No memcpy for most of in-place IO (about 99% of enwik9) after
decompression inplace is implemented and sequential read will
be improved of course (see the following patches for test results).

[1] https://github.com/lz4/lz4/commit/b17f578a919b7e6b078cede2d52be29dd48c8e8c
    https://github.com/lz4/lz4/commit/5997e139f53169fa3a1c1b4418d2452a90b01602

Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Gao Xiang <gaoxiang25@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: erofs: introduce generic decompression backend

This patch adds a new generic decompression framework
in order to replace the old LZ4-specific decompression code.

Even though LZ4 is still the only supported algorithm, yet
it is more cleaner and easy to integrate new algorithm than
the old almost hard-coded decompression backend.

Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Gao Xiang <gaoxiang25@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: erofs: move stagingpage operations to compress.h

stagingpages are behaved as bounce pages for temporary use.
Move to compress.h since the upcoming decompressor will
allocate stagingpages as well.

Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Gao Xiang <gaoxiang25@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: erofs: move per-CPU buffers implementation to utils.c

This patch moves per-CPU buffers to utils.c in order for
the upcoming generic decompression framework to use it.

Note that I tried to use generic per-CPU buffer or
per-CPU page approaches to clean up further, but obvious
performanace regression (about 2% for sequential read) was
observed.

Therefore let's leave it as it is instead, just move
to utils.c and I'll try to dig into the root cause later.

Signed-off-by: Gao Xiang <gaoxiang25@huawei.com>
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: erofs: add compacted compression indexes support

This patch aims at compacted compression indexes:
 1) cleanup z_erofs_map_blocks_iter and move into zmap.c;
 2) add compacted 4/2B decoding support.

On kirin980 platform, sequential read is increased about
6% (725MiB/s -> 770MiB/s) on enwik9 dataset if compacted 2B
feature is enabled.

Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Gao Xiang <gaoxiang25@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: erofs: add compacted ondisk compression indexes

This patch introduces new compacted compression indexes.

In contract to legacy compression indexes that
   each 4k logical cluster has an 8-byte index,
compacted ondisk compression indexes will have
   amortized 2 bytes for each 4k logical cluster (compacted 2B)
   amortized 4 bytes for each 4k logical cluster (compacted 4B)

In detail, several continuous clusters will be encoded in
a compacted pack with cluster types, offsets, and one blkaddr
at the end of the pack to leave 4-byte margin for better
decoding performance, as illustrated below:
   _____________________________________________
  |___@_____ encoded bits __________|_ blkaddr _|
  0       .                                     amortized * vcnt
  .          .
  .             .                   amortized * vcnt - 4
  .                .
  .___________________.
  |_type_|_clusterofs_|

Note that compacted 2 / 4B should be aligned with 32 / 8 bytes
in order to avoid each pack crossing page boundary.

Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Gao Xiang <gaoxiang25@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: comedi: use dma_mmap_coherent for DMA-able buffer mmap

Comedi's acquisition buffer allocation code can allocate the buffer from
normal kernel memory or from DMA coherent memory depending on the
`dma_async_dir` value in the comedi subdevice.  (A value of `DMA_NONE`
causes the buffer to be allocated from normal kernel memory.  Other
values cause the buffer to be allocated from DMA coherent memory.)   The
buffer currently consists of a bunch of page-sized blocks that are
vmap'ed into a contiguous range of virtual addresses. The pages are also
mmap'able into user address space.  For DMA'able buffers, these
page-sized blocks are allocated by `dma_alloc_coherent()`.

For DMA-able buffers, the DMA API is currently abused in various ways,
the most serious abuse being the calling of `virt_to_page()` on the
blocks allocated by `dma_alloc_coherent()` and passing those pages to
`vmap()` (for mapping to the kernels vmalloc address space) and via
`page_to_pfn()` to `remap_pfn_range()` (for mmap'ing to user space).  it
also uses the `__GFP_COMP` flag when allocating the blocks, and marks
the allocated pages as reserved (which is unnecessary for DMA coherent
allocations).

The code can be changed to get rid of the vmap'ed address altogether if
necessary, since there are only a few places in the comedi code that use
the vmap'ed address directly and we also keep a list of the kernel
addresses for the individual pages prior to the vmap operation. This
would add some run-time overhead to buffer accesses.  The real killer is
the mmap operation.

For mmap, the address range specified in the VMA needs to be mmap'ed to
the individually allocated page-sized blocks.  That is not a problem
when the pages are allocated from normal kernel memory as the individual
pages can be remapped by `remap_pfn_range()`, but it is a problem when
the page-sized blocks are allocated by `dma_alloc_coherent()` because
the DMA API currently has no support for splitting a VMA across multiple
blocks of DMA coherent memory (or rather, no support for mapping part of
a VMA range to a single block of DMA coherent memory).

In order to comply with the DMA API and allow the buffer to be mmap'ed,
the buffer needs to be allocated as a single block by a single call to
`dma_alloc_coherent()`, freed by a single call to `dma_free_coherent()`,
and mmap'ed to user space by a single call to `dma_mmap_coherent()`.
This patch changes the buffer allocation, freeing, and mmap'ing code to
do that, with the unfortunate consequence that buffer allocation is more
likely to fail.  It also no longer uses the `__GFP_COMP` flag when
allocating DMA coherent memory, no longer marks the
allocated pages of DMA coherent memory as reserved, and no longer vmap's
the DMA coherent memory pages (since they are contiguous anyway).

Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Revert "staging: ks7010: Fix build error"

This reverts commit 3e5bc68fa596874500e8c718605aa44d5e42a34c as it
causes build errors in linux-next.

Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge 5.2-rc6 into staging-next

We want the fixes and this resolves a merge issue as well.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Linux 5.2-rc6

Merge tag 'iommu-fix-v5.2-rc5' of git://git./linux/kernel/git/joro/iommu

Pull iommu fix from Joerg Roedel:
 "Revert a commit from the previous pile of fixes which causes new
  lockdep splats. It is better to revert it for now and work on a better
  and more well tested fix"

* tag 'iommu-fix-v5.2-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
  Revert "iommu/vt-d: Fix lock inversion between iommu->lock and device_domain_lock"

Revert "iommu/vt-d: Fix lock inversion between iommu->lock and device_domain_lock"

This reverts commit 7560cc3ca7d9d11555f80c830544e463fcdb28b8.

With 5.2.0-rc5 I can easily trigger this with lockdep and iommu=pt:

    ======================================================
    WARNING: possible circular locking dependency detected
    5.2.0-rc5 #78 Not tainted
    ------------------------------------------------------
    swapper/0/1 is trying to acquire lock:
    00000000ea2b3beb (&(&iommu->lock)->rlock){+.+.}, at: domain_context_mapping_one+0xa5/0x4e0
    but task is already holding lock:
    00000000a681907b (device_domain_lock){....}, at: domain_context_mapping_one+0x8d/0x4e0
    which lock already depends on the new lock.
    the existing dependency chain (in reverse order) is:
    -> #1 (device_domain_lock){....}:
           _raw_spin_lock_irqsave+0x3c/0x50
           dmar_insert_one_dev_info+0xbb/0x510
           domain_add_dev_info+0x50/0x90
           dev_prepare_static_identity_mapping+0x30/0x68
           intel_iommu_init+0xddd/0x1422
           pci_iommu_init+0x16/0x3f
           do_one_initcall+0x5d/0x2b4
           kernel_init_freeable+0x218/0x2c1
           kernel_init+0xa/0x100
           ret_from_fork+0x3a/0x50
    -> #0 (&(&iommu->lock)->rlock){+.+.}:
           lock_acquire+0x9e/0x170
           _raw_spin_lock+0x25/0x30
           domain_context_mapping_one+0xa5/0x4e0
           pci_for_each_dma_alias+0x30/0x140
           dmar_insert_one_dev_info+0x3b2/0x510
           domain_add_dev_info+0x50/0x90
           dev_prepare_static_identity_mapping+0x30/0x68
           intel_iommu_init+0xddd/0x1422
           pci_iommu_init+0x16/0x3f
           do_one_initcall+0x5d/0x2b4
           kernel_init_freeable+0x218/0x2c1
           kernel_init+0xa/0x100
           ret_from_fork+0x3a/0x50

    other info that might help us debug this:
     Possible unsafe locking scenario:
           CPU0                    CPU1
           ----                    ----
      lock(device_domain_lock);
                                   lock(&(&iommu->lock)->rlock);
                                   lock(device_domain_lock);
      lock(&(&iommu->lock)->rlock);

     *** DEADLOCK ***
    2 locks held by swapper/0/1:
     #0: 00000000033eb13d (dmar_global_lock){++++}, at: intel_iommu_init+0x1e0/0x1422
     #1: 00000000a681907b (device_domain_lock){....}, at: domain_context_mapping_one+0x8d/0x4e0

    stack backtrace:
    CPU: 2 PID: 1 Comm: swapper/0 Not tainted 5.2.0-rc5 #78
    Hardware name: LENOVO 20KGS35G01/20KGS35G01, BIOS N23ET50W (1.25 ) 06/25/2018
    Call Trace:
     dump_stack+0x85/0xc0
     print_circular_bug.cold.57+0x15c/0x195
     __lock_acquire+0x152a/0x1710
     lock_acquire+0x9e/0x170
     ? domain_context_mapping_one+0xa5/0x4e0
     _raw_spin_lock+0x25/0x30
     ? domain_context_mapping_one+0xa5/0x4e0
     domain_context_mapping_one+0xa5/0x4e0
     ? domain_context_mapping_one+0x4e0/0x4e0
     pci_for_each_dma_alias+0x30/0x140
     dmar_insert_one_dev_info+0x3b2/0x510
     domain_add_dev_info+0x50/0x90
     dev_prepare_static_identity_mapping+0x30/0x68
     intel_iommu_init+0xddd/0x1422
     ? printk+0x58/0x6f
     ? lockdep_hardirqs_on+0xf0/0x180
     ? do_early_param+0x8e/0x8e
     ? e820__memblock_setup+0x63/0x63
     pci_iommu_init+0x16/0x3f
     do_one_initcall+0x5d/0x2b4
     ? do_early_param+0x8e/0x8e
     ? rcu_read_lock_sched_held+0x55/0x60
     ? do_early_param+0x8e/0x8e
     kernel_init_freeable+0x218/0x2c1
     ? rest_init+0x230/0x230
     kernel_init+0xa/0x100
     ret_from_fork+0x3a/0x50

domain_context_mapping_one() is taking device_domain_lock first then
iommu lock, while dmar_insert_one_dev_info() is doing the reverse.

That should be introduced by commit:

7560cc3ca7d9 ("iommu/vt-d: Fix lock inversion between iommu->lock and
              device_domain_lock", 2019-05-27)

So far I still cannot figure out how the previous deadlock was
triggered (I cannot find iommu lock taken before calling of
iommu_flush_dev_iotlb()), however I'm pretty sure that that change
should be incomplete at least because it does not fix all the places
so we're still taking the locks in different orders, while reverting
that commit is very clean to me so far that we should always take
device_domain_lock first then the iommu lock.

We can continue to try to find the real culprit mentioned in
7560cc3ca7d9, but for now I think we should revert it to fix current
breakage.

CC: Joerg Roedel <joro@8bytes.org>
CC: Lu Baolu <baolu.lu@linux.intel.com>
CC: dave.jiang@intel.com
Signed-off-by: Peter Xu <peterx@redhat.com>
Tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Joerg Roedel <jroedel@suse.de>

Merge tag 'pci-v5.2-fixes-1' of git://git./linux/kernel/git/helgaas/pci

Pull PCI fix from Bjorn Helgaas:
 "If an IOMMU is present, ignore the P2PDMA whitelist we added for v5.2
  because we don't yet know how to support P2PDMA in that case (Logan
  Gunthorpe)"

* tag 'pci-v5.2-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  PCI/P2PDMA: Ignore root complex whitelist when an IOMMU is present

Merge tag 'scsi-fixes' of git://git./linux/kernel/git/jejb/scsi

Pull SCSI fixes from James Bottomley:
 "Three driver fixes (and one version number update): a suspend hang in
  ufs, a qla hard lock on module removal and a qedi panic during
  discovery"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: qla2xxx: Fix hardlockup in abort command during driver remove
  scsi: ufs: Avoid runtime suspend possibly being blocked forever
  scsi: qedi: update driver version to 8.37.0.20
  scsi: qedi: Check targetname while finding boot target information