Evan Nimmo [Tue, 8 Sep 2020 20:32:47 +0000 (08:32 +1200)]
i2c: algo: pca: Reapply i2c bus settings after reset
[ Upstream commit
0a355aeb24081e4538d4d424cd189f16c0bbd983 ]
If something goes wrong (such as the SCL being stuck low) then we need
to reset the PCA chip. The issue with this is that on reset we lose all
config settings and the chip ends up in a disabled state which results
in a lock up/high CPU usage. We need to re-apply any configuration that
had previously been set and re-enable the chip.
Signed-off-by: Evan Nimmo <evan.nimmo@alliedtelesis.co.nz>
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Laurent Pinchart [Tue, 28 Jul 2020 22:19:40 +0000 (01:19 +0300)]
rapidio: Replace 'select' DMAENGINES 'with depends on'
[ Upstream commit
d2b86100245080cfdf1e95e9e07477474c1be2bd ]
Enabling a whole subsystem from a single driver 'select' is frowned
upon and won't be accepted in new drivers, that need to use 'depends on'
instead. Existing selection of DMAENGINES will then cause circular
dependencies. Replace them with a dependency.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
J. Bruce Fields [Sat, 5 Sep 2020 14:03:26 +0000 (10:03 -0400)]
SUNRPC: stop printk reading past end of string
[ Upstream commit
8c6b6c793ed32b8f9770ebcdf1ba99af423c303b ]
Since p points at raw xdr data, there's no guarantee that it's NULL
terminated, so we should give a length. And probably escape any special
characters too.
Reported-by: Zhi Li <yieli@redhat.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Vincent Whitchurch [Wed, 2 Sep 2020 13:23:41 +0000 (15:23 +0200)]
spi: spi-loopback-test: Fix out-of-bounds read
[ Upstream commit
837ba18dfcd4db21ad58107c65bfe89753aa56d7 ]
The "tx/rx-transfer - crossing PAGE_SIZE" test always fails when
len=131071 and rx_offset >= 5:
spi-loopback-test spi0.0: Running test tx/rx-transfer - crossing PAGE_SIZE
...
with iteration values: len = 131071, tx_off = 0, rx_off = 3
with iteration values: len = 131071, tx_off = 0, rx_off = 4
with iteration values: len = 131071, tx_off = 0, rx_off = 5
loopback strangeness - rx changed outside of allowed range at: ...
a4321000
spi_msg@
ffffffd5a4157690
frame_length: 131071
actual_length: 131071
spi_transfer@
ffffffd5a41576f8
len: 131071
tx_buf:
ffffffd5a4340ffc
Note that rx_offset > 3 can only occur if the SPI controller driver sets
->dma_alignment to a higher value than 4, so most SPI controller drivers
are not affect.
The allocated Rx buffer is of size SPI_TEST_MAX_SIZE_PLUS, which is 132
KiB (assuming 4 KiB pages). This test uses an initial offset into the
rx_buf of PAGE_SIZE - 4, and a len of 131071, so the range expected to
be written in this transfer ends at (4096 - 4) + 5 + 131071 == 132 KiB,
which is also the end of the allocated buffer. But the code which
verifies the content of the buffer reads a byte beyond the allocated
buffer and spuriously fails because this out-of-bounds read doesn't
return the expected value.
Fix this by using ITERATE_LEN instead of ITERATE_MAX_LEN to avoid
testing sizes which cause out-of-bounds reads.
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Link: https://lore.kernel.org/r/20200902132341.7079-1-vincent.whitchurch@axis.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
James Smart [Fri, 28 Aug 2020 17:53:30 +0000 (10:53 -0700)]
scsi: lpfc: Fix FLOGI/PLOGI receive race condition in pt2pt discovery
[ Upstream commit
7b08e89f98cee9907895fabb64cf437bc505ce9a ]
The driver is unable to successfully login with remote device. During pt2pt
login, the driver completes its FLOGI request with the remote device having
WWN precedence. The remote device issues its own (delayed) FLOGI after
accepting the driver's and, upon transmitting the FLOGI, immediately
recognizes it has already processed the driver's FLOGI thus it transitions
to sending a PLOGI before waiting for an ACC to its FLOGI.
In the driver, the FLOGI is received and an ACC sent, followed by the PLOGI
being received and an ACC sent. The issue is that the PLOGI reception
occurs before the response from the adapter from the FLOGI ACC is
received. Processing of the PLOGI sets state flags to perform the REG_RPI
mailbox command and proceed with the rest of discovery on the port. The
same completion routine used by both FLOGI and PLOGI is generic in
nature. One of the things it does is clear flags, and those flags happen to
drive the rest of discovery. So what happened was the PLOGI processing set
the flags, the FLOGI ACC completion cleared them, thus when the PLOGI ACC
completes it doesn't see the flags and stops.
Fix by modifying the generic completion routine to not clear the rest of
discovery flag (NLP_ACC_REGLOGIN) unless the completion is also associated
with performing a mailbox command as part of its handling. For things such
as FLOGI ACC, there isn't a subsequent action to perform with the adapter,
thus there is no mailbox cmd ptr. PLOGI ACC though will perform REG_RPI
upon completion, thus there is a mailbox cmd ptr.
Link: https://lore.kernel.org/r/20200828175332.130300-3-james.smart@broadcom.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Dinghao Liu [Sun, 23 Aug 2020 09:14:53 +0000 (17:14 +0800)]
scsi: pm8001: Fix memleak in pm8001_exec_internal_task_abort
[ Upstream commit
ea403fde7552bd61bad6ea45e3feb99db77cb31e ]
When pm8001_tag_alloc() fails, task should be freed just like it is done in
the subsequent error paths.
Link: https://lore.kernel.org/r/20200823091453.4782-1-dinghao.liu@zju.edu.cn
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Olga Kornievskaia [Thu, 20 Aug 2020 22:52:43 +0000 (18:52 -0400)]
NFSv4.1 handle ERR_DELAY error reclaiming locking state on delegation recall
[ Upstream commit
3d7a9520f0c3e6a68b6de8c5812fc8b6d7a52626 ]
A client should be able to handle getting an ERR_DELAY error
while doing a LOCK call to reclaim state due to delegation being
recalled. This is a transient error that can happen due to server
moving its volumes and invalidating its file location cache and
upon reference to it during the LOCK call needing to do an
expensive lookup (leading to an ERR_DELAY error on a PUTFH).
Signed-off-by: Olga Kornievskaia <kolga@netapp.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Miaohe Lin [Sat, 15 Aug 2020 08:46:41 +0000 (04:46 -0400)]
net: handle the return value of pskb_carve_frag_list() correctly
commit
eabe861881a733fc84f286f4d5a1ffaddd4f526f upstream.
pskb_carve_frag_list() may return -ENOMEM in pskb_carve_inside_nonlinear().
we should handle this correctly or we would get wrong sk_buff.
Fixes:
6fa01ccd8830 ("skbuff: Add pskb_extract() helper function")
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Oberparleiter [Thu, 10 Sep 2020 12:52:01 +0000 (14:52 +0200)]
gcov: add support for GCC 10.1
[ Upstream commit
40249c6962075c040fd071339acae524f18bfac9 ]
Using gcov to collect coverage data for kernels compiled with GCC 10.1
causes random malfunctions and kernel crashes. This is the result of a
changed GCOV_COUNTERS value in GCC 10.1 that causes a mismatch between
the layout of the gcov_info structure created by GCC profiling code and
the related structure used by the kernel.
Fix this by updating the in-kernel GCOV_COUNTERS value. Also re-enable
config GCOV_KERNEL for use with GCC 10.
Reported-by: Colin Ian King <colin.king@canonical.com>
Reported-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Tested-by: Leon Romanovsky <leonro@nvidia.com>
Tested-and-Acked-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Yi Zhang [Thu, 20 Aug 2020 15:36:46 +0000 (23:36 +0800)]
RDMA/rxe: Fix the parent sysfs read when the interface has 15 chars
[ Upstream commit
60b1af64eb35074a4f2d41cc1e503a7671e68963 ]
'parent' sysfs reads will yield '\0' bytes when the interface name has 15
chars, and there will no "\n" output.
To reproduce, create one interface with 15 chars:
[root@test ~]# ip a s enp0s29u1u7u3c2
2: enp0s29u1u7u3c2: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel state UNKNOWN group default qlen 1000
link/ether 02:21:28:57:47:17 brd ff:ff:ff:ff:ff:ff
inet6 fe80::ac41:338f:5bcd:c222/64 scope link noprefixroute
valid_lft forever preferred_lft forever
[root@test ~]# modprobe rdma_rxe
[root@test ~]# echo enp0s29u1u7u3c2 > /sys/module/rdma_rxe/parameters/add
[root@test ~]# cat /sys/class/infiniband/rxe0/parent
enp0s29u1u7u3c2[root@test ~]#
[root@test ~]# f="/sys/class/infiniband/rxe0/parent"
[root@test ~]# echo "$(<"$f")"
-bash: warning: command substitution: ignored null byte in input
enp0s29u1u7u3c2
Use scnprintf and PAGE_SIZE to fill the sysfs output buffer.
Cc: stable@vger.kernel.org
Fixes:
8700e3e7c485 ("Soft RoCE driver")
Link: https://lore.kernel.org/r/20200820153646.31316-1-yi.zhang@redhat.com
Suggested-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Yi Zhang <yi.zhang@redhat.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Bart Van Assche [Tue, 10 Jan 2017 19:15:53 +0000 (11:15 -0800)]
IB/rxe: Remove a pointless indirection layer
[ Upstream commit
839f5ac0d806970a102117be03ef05272c50d20e ]
Neither rxe->ifc_ops nor any of the function pointers in struct
struct rxe_ifc_ops ever change. Hence remove the rxe->ifc_ops
indirection mechanism.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Andrew Boyer <andrew.boyer@dell.com>
Cc: Moni Shoua <monis@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Mathias Nyman [Tue, 1 Sep 2020 08:25:28 +0000 (11:25 +0300)]
usb: Fix out of sync data toggle if a configured device is reconfigured
commit
cfd54fa83a5068b61b7eb28d3c117d8354c74c7a upstream.
Userspace drivers that use a SetConfiguration() request to "lightweight"
reset an already configured usb device might cause data toggles to get out
of sync between the device and host, and the device becomes unusable.
The xHCI host requires endpoints to be dropped and added back to reset the
toggle. If USB core notices the new configuration is the same as the
current active configuration it will avoid these extra steps by calling
usb_reset_configuration() instead of usb_set_configuration().
A SetConfiguration() request will reset the device side data toggles.
Make sure usb_reset_configuration() function also drops and adds back the
endpoints to ensure data toggles are in sync.
To avoid code duplication split the current usb_disable_device() function
and reuse the endpoint specific part.
Cc: stable <stable@vger.kernel.org>
Tested-by: Martin Thierer <mthierer@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200901082528.12557-1-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Aleksander Morgado [Sat, 29 Aug 2020 09:05:39 +0000 (11:05 +0200)]
USB: serial: option: add support for SIM7070/SIM7080/SIM7090 modules
commit
1ac698790819b83f39fd7ea4f6cdabee9bdd7b38 upstream.
These modules have 2 different USB layouts:
The default layout with PID 0x9205 (AT+CUSBSELNV=1) exposes 4 TTYs and
an ECM interface:
T: Bus=02 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 6 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=1e0e ProdID=9205 Rev=00.00
S: Manufacturer=SimTech, Incorporated
S: Product=SimTech SIM7080
S: SerialNumber=
1234567890ABCDEF
C: #Ifs= 6 Cfg#= 1 Atr=e0 MxPwr=500mA
I: If#=0x0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I: If#=0x1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I: If#=0x2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I: If#=0x3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I: If#=0x4 Alt= 0 #EPs= 1 Cls=02(commc) Sub=06 Prot=00 Driver=cdc_ether
I: If#=0x5 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
The purpose of each TTY is as follows:
* ttyUSB0: DIAG/QCDM port.
* ttyUSB1: GNSS data.
* ttyUSB2: AT-capable port (control).
* ttyUSB3: AT-capable port (data).
In the secondary layout with PID=0x9206 (AT+CUSBSELNV=86) the module
exposes 6 TTY ports:
T: Bus=02 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 8 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=02(commc) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1e0e ProdID=9206 Rev=00.00
S: Manufacturer=SimTech, Incorporated
S: Product=SimTech SIM7080
S: SerialNumber=
1234567890ABCDEF
C: #Ifs= 6 Cfg#= 1 Atr=e0 MxPwr=500mA
I: If#=0x0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I: If#=0x1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I: If#=0x2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I: If#=0x3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I: If#=0x4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I: If#=0x5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
The purpose of each TTY is as follows:
* ttyUSB0: DIAG/QCDM port.
* ttyUSB1: GNSS data.
* ttyUSB2: AT-capable port (control).
* ttyUSB3: QFLOG interface.
* ttyUSB4: DAM interface.
* ttyUSB5: AT-capable port (data).
Signed-off-by: Aleksander Morgado <aleksander@aleksander.es>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Patrick Riphagen [Thu, 6 Aug 2020 11:55:47 +0000 (13:55 +0200)]
USB: serial: ftdi_sio: add IDs for Xsens Mti USB converter
commit
6ccc48e0eb2f3a5f3bd39954a21317e5f8874726 upstream.
The device added has an FTDI chip inside.
The device is used to connect Xsens USB Motion Trackers.
Cc: stable@vger.kernel.org
Signed-off-by: Patrick Riphagen <patrick.riphagen@xsens.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Zeng Tao [Fri, 4 Sep 2020 06:37:44 +0000 (14:37 +0800)]
usb: core: fix slab-out-of-bounds Read in read_descriptors
commit
a18cd6c9b6bc73dc17e8b7e9bd07decaa8833c97 upstream.
The USB device descriptor may get changed between two consecutive
enumerations on the same device for some reason, such as DFU or
malicius device.
In that case, we may access the changing descriptor if we don't take
the device lock here.
The issue is reported:
https://syzkaller.appspot.com/bug?id=
901a0d9e6519ef8dc7acab25344bd287dd3c7be9
Cc: stable <stable@vger.kernel.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Reported-by: syzbot+256e56ddde8b8957eabd@syzkaller.appspotmail.com
Fixes:
217a9081d8e6 ("USB: add all configs to the "descriptors" attribute")
Signed-off-by: Zeng Tao <prime.zeng@hisilicon.com>
Link: https://lore.kernel.org/r/1599201467-11000-1-git-send-email-prime.zeng@hisilicon.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Vaibhav Agarwal [Fri, 14 Aug 2020 12:33:15 +0000 (18:03 +0530)]
staging: greybus: audio: fix uninitialized value issue
commit
1dffeb8b8b4c261c45416d53c75ea51e6ece1770 upstream.
The current implementation for gbcodec_mixer_dapm_ctl_put() uses
uninitialized gbvalue for comparison with updated value. This was found
using static analysis with coverity.
Uninitialized scalar variable (UNINIT)
11. uninit_use: Using uninitialized value
gbvalue.value.integer_value[0].
460 if (gbvalue.value.integer_value[0] != val) {
This patch fixes the issue with fetching the gbvalue before using it for
comparision.
Fixes:
6339d2322c47 ("greybus: audio: Add topology parser for GB codec")
Reported-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Vaibhav Agarwal <vaibhav.sr@gmail.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/bc4f29eb502ccf93cd2ffd98db0e319fa7d0f247.1597408126.git.vaibhav.sr@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tetsuo Handa [Mon, 31 Aug 2020 10:37:00 +0000 (19:37 +0900)]
video: fbdev: fix OOB read in vga_8planes_imageblit()
commit
bd018a6a75cebb511bb55a0e7690024be975fe93 upstream.
syzbot is reporting OOB read at vga_8planes_imageblit() [1], for
"cdat[y] >> 4" can become a negative value due to "const char *cdat".
[1] https://syzkaller.appspot.com/bug?id=
0d7a0da1557dcd1989e00cb3692b26d4173b4132
Reported-by: syzbot <syzbot+69fbd3e01470f169c8c4@syzkaller.appspotmail.com>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/90b55ec3-d5b0-3307-9f7c-7ff5c5fd6ad3@i-love.sakura.ne.jp
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Wanpeng Li [Wed, 19 Aug 2020 08:55:27 +0000 (16:55 +0800)]
KVM: VMX: Don't freeze guest when event delivery causes an APIC-access exit
commit
99b82a1437cb31340dbb2c437a2923b9814a7b15 upstream.
According to SDM 27.2.4, Event delivery causes an APIC-access VM exit.
Don't report internal error and freeze guest when event delivery causes
an APIC-access exit, it is handleable and the event will be re-injected
during the next vmentry.
Signed-off-by: Wanpeng Li <wanpengli@tencent.com>
Message-Id: <
1597827327-25055-2-git-send-email-wanpengli@tencent.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Torvalds [Wed, 9 Sep 2020 21:53:50 +0000 (14:53 -0700)]
vgacon: remove software scrollback support
commit
973c096f6a85e5b5f2a295126ba6928d9a6afd45 upstream.
Yunhai Zhang recently fixed a VGA software scrollback bug in commit
ebfdfeeae8c0 ("vgacon: Fix for missing check in scrollback handling"),
but that then made people look more closely at some of this code, and
there were more problems on the vgacon side, but also the fbcon software
scrollback.
We don't really have anybody who maintains this code - probably because
nobody actually _uses_ it any more. Sure, people still use both VGA and
the framebuffer consoles, but they are no longer the main user
interfaces to the kernel, and haven't been for decades, so these kinds
of extra features end up bitrotting and not really being used.
So rather than try to maintain a likely unused set of code, I'll just
aggressively remove it, and see if anybody even notices. Maybe there
are people who haven't jumped on the whole GUI badnwagon yet, and think
it's just a fad. And maybe those people use the scrollback code.
If that turns out to be the case, we can resurrect this again, once
we've found the sucker^Wmaintainer for it who actually uses it.
Reported-by: NopNop Nop <nopitydays@gmail.com>
Tested-by: Willy Tarreau <w@1wt.eu>
Cc: 张云海 <zhangyunhai@nsfocus.com>
Acked-by: Andy Lutomirski <luto@amacapital.net>
Acked-by: Willy Tarreau <w@1wt.eu>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Torvalds [Tue, 8 Sep 2020 17:56:27 +0000 (10:56 -0700)]
fbcon: remove now unusued 'softback_lines' cursor() argument
commit
06a0df4d1b8b13b551668e47b11fd7629033b7df upstream.
Since the softscroll code got removed, this argument is always zero and
makes no sense any more.
Tested-by: Yuan Ming <yuanmingbuaa@gmail.com>
Tested-by: Willy Tarreau <w@1wt.eu>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Torvalds [Mon, 7 Sep 2020 18:45:27 +0000 (11:45 -0700)]
fbcon: remove soft scrollback code
commit
50145474f6ef4a9c19205b173da6264a644c7489 upstream.
This (and the VGA soft scrollback) turns out to have various nasty small
special cases that nobody really is willing to fight. The soft
scrollback code was really useful a few decades ago when you typically
used the console interactively as the main way to interact with the
machine, but that just isn't the case any more.
So it's not worth dragging along.
Tested-by: Yuan Ming <yuanmingbuaa@gmail.com>
Tested-by: Willy Tarreau <w@1wt.eu>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ilya Dryomov [Thu, 3 Sep 2020 11:24:11 +0000 (13:24 +0200)]
rbd: require global CAP_SYS_ADMIN for mapping and unmapping
commit
f44d04e696feaf13d192d942c4f14ad2e117065a upstream.
It turns out that currently we rely only on sysfs attribute
permissions:
$ ll /sys/bus/rbd/{add*,remove*}
--w------- 1 root root 4096 Sep 3 20:37 /sys/bus/rbd/add
--w------- 1 root root 4096 Sep 3 20:37 /sys/bus/rbd/add_single_major
--w------- 1 root root 4096 Sep 3 20:37 /sys/bus/rbd/remove
--w------- 1 root root 4096 Sep 3 20:38 /sys/bus/rbd/remove_single_major
This means that images can be mapped and unmapped (i.e. block devices
can be created and deleted) by a UID 0 process even after it drops all
privileges or by any process with CAP_DAC_OVERRIDE in its user namespace
as long as UID 0 is mapped into that user namespace.
Be consistent with other virtual block devices (loop, nbd, dm, md, etc)
and require CAP_SYS_ADMIN in the initial user namespace for mapping and
unmapping, and also for dumping the configuration string and refreshing
the image header.
Cc: stable@vger.kernel.org
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hou Pu [Wed, 29 Jul 2020 13:03:43 +0000 (09:03 -0400)]
scsi: target: iscsi: Fix hang in iscsit_access_np() when getting tpg->np_login_sem
commit
ed43ffea78dcc97db3f561da834f1a49c8961e33 upstream.
The iSCSI target login thread might get stuck with the following stack:
cat /proc/`pidof iscsi_np`/stack
[<0>] down_interruptible+0x42/0x50
[<0>] iscsit_access_np+0xe3/0x167
[<0>] iscsi_target_locate_portal+0x695/0x8ac
[<0>] __iscsi_target_login_thread+0x855/0xb82
[<0>] iscsi_target_login_thread+0x2f/0x5a
[<0>] kthread+0xfa/0x130
[<0>] ret_from_fork+0x1f/0x30
This can be reproduced via the following steps:
1. Initiator A tries to log in to iqn1-tpg1 on port 3260. After finishing
PDU exchange in the login thread and before the negotiation is finished
the the network link goes down. At this point A has not finished login
and tpg->np_login_sem is held.
2. Initiator B tries to log in to iqn2-tpg1 on port 3260. After finishing
PDU exchange in the login thread the target expects to process remaining
login PDUs in workqueue context.
3. Initiator A' tries to log in to iqn1-tpg1 on port 3260 from a new
socket. A' will wait for tpg->np_login_sem with np->np_login_timer
loaded to wait for at most 15 seconds. The lock is held by A so A'
eventually times out.
4. Before A' got timeout initiator B gets negotiation failed and calls
iscsi_target_login_drop()->iscsi_target_login_sess_out(). The
np->np_login_timer is canceled and initiator A' will hang forever.
Because A' is now in the login thread, no new login requests can be
serviced.
Fix this by moving iscsi_stop_login_thread_timer() out of
iscsi_target_login_sess_out(). Also remove iscsi_np parameter from
iscsi_target_login_sess_out().
Link: https://lore.kernel.org/r/20200729130343.24976-1-houpu@bytedance.com
Cc: stable@vger.kernel.org
Reviewed-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Hou Pu <houpu@bytedance.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Varun Prakash [Tue, 25 Aug 2020 12:35:10 +0000 (18:05 +0530)]
scsi: target: iscsi: Fix data digest calculation
commit
5528d03183fe5243416c706f64b1faa518b05130 upstream.
Current code does not consider 'page_off' in data digest calculation. To
fix this, add a local variable 'first_sg' and set first_sg.offset to
sg->offset + page_off.
Link: https://lore.kernel.org/r/1598358910-3052-1-git-send-email-varun@chelsio.com
Fixes:
e48354ce078c ("iscsi-target: Add iSCSI fabric support for target v4.1")
Cc: <stable@vger.kernel.org>
Reviewed-by: Mike Christie <michael.christie@oralce.com>
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Michał Mirosław [Wed, 12 Aug 2020 01:31:36 +0000 (03:31 +0200)]
regulator: push allocation in set_consumer_device_supply() out of lock
commit
5c06540165d443c6455123eb48e7f1a9b618ab34 upstream.
Pull regulator_list_mutex into set_consumer_device_supply() and keep
allocations outside of it. Fourth of the fs_reclaim deadlock case.
Fixes:
45389c47526d ("regulator: core: Add early supply resolution for regulators")
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/f0380bdb3d60aeefa9693c4e234d2dcda7e56747.1597195321.git.mirq-linux@rere.qmqm.pl
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Filipe Manana [Mon, 14 Sep 2020 08:01:04 +0000 (09:01 +0100)]
btrfs: fix wrong address when faulting in pages in the search ioctl
commit
1c78544eaa4660096aeb6a57ec82b42cdb3bfe5a upstream.
When faulting in the pages for the user supplied buffer for the search
ioctl, we are passing only the base address of the buffer to the function
fault_in_pages_writeable(). This means that after the first iteration of
the while loop that searches for leaves, when we have a non-zero offset,
stored in 'sk_offset', we try to fault in a wrong page range.
So fix this by adding the offset in 'sk_offset' to the base address of the
user supplied buffer when calling fault_in_pages_writeable().
Several users have reported that the applications compsize and bees have
started to operate incorrectly since commit
a48b73eca4ceb9 ("btrfs: fix
potential deadlock in the search ioctl") was added to stable trees, and
these applications make heavy use of the search ioctls. This fixes their
issues.
Link: https://lore.kernel.org/linux-btrfs/632b888d-a3c3-b085-cdf5-f9bb61017d92@lechevalier.se/
Link: https://github.com/kilobyte/compsize/issues/34
Fixes:
a48b73eca4ceb9 ("btrfs: fix potential deadlock in the search ioctl")
CC: stable@vger.kernel.org # 4.4+
Tested-by: A L <mail@lechevalier.se>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rustam Kovhaev [Tue, 4 Aug 2020 14:56:14 +0000 (07:56 -0700)]
staging: wlan-ng: fix out of bounds read in prism2sta_probe_usb()
commit
fea22e159d51c766ba70473f473a0ec914cc7e92 upstream.
let's use usb_find_common_endpoints() to discover endpoints, it does all
necessary checks for type and xfer direction
remove memset() in hfa384x_create(), because we now assign endpoints in
prism2sta_probe_usb() and because create_wlan() uses kzalloc() to
allocate hfa384x struct before calling hfa384x_create()
Fixes:
faaff9765664 ("staging: wlan-ng: properly check endpoint types")
Reported-and-tested-by: syzbot+22794221ab96b0bab53a@syzkaller.appspotmail.com
Link: https://syzkaller.appspot.com/bug?extid=22794221ab96b0bab53a
Signed-off-by: Rustam Kovhaev <rkovhaev@gmail.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200804145614.104320-1-rkovhaev@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Fri, 17 Mar 2017 10:35:30 +0000 (11:35 +0100)]
USB: core: add helpers to retrieve endpoints
commit
66a359390e7e34f9a4c489467234b107b3d76169 upstream.
Many USB drivers iterate over the available endpoints to find required
endpoints of a specific type and direction. Typically the endpoints are
required for proper function and a missing endpoint should abort probe.
To facilitate code reuse, add a helper to retrieve common endpoints
(bulk or interrupt, in or out) and four wrappers to find a single
endpoint.
Note that the helpers are marked as __must_check to serve as a reminder
to always verify that all expected endpoints are indeed present. This
also means that any optional endpoints, typically need to be looked up
through separate calls.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jonathan Cameron [Wed, 22 Jul 2020 15:50:38 +0000 (16:50 +0100)]
iio:accel:mma8452: Fix timestamp alignment and prevent data leak.
commit
89226a296d816727405d3fea684ef69e7d388bd8 upstream.
One of a class of bugs pointed out by Lars in a recent review.
iio_push_to_buffers_with_timestamp assumes the buffer used is aligned
to the size of the timestamp (8 bytes). This is not guaranteed in
this driver which uses a 16 byte u8 array on the stack. As Lars also noted
this anti pattern can involve a leak of data to userspace and that
indeed can happen here. We close both issues by moving to
a suitable structure in the iio_priv() data with alignment
ensured by use of an explicit c structure. This data is allocated
with kzalloc so no data can leak appart from previous readings.
The additional forcing of the 8 byte alignment of the timestamp
is not strictly necessary but makes the code less fragile by
making this explicit.
Fixes:
c7eeea93ac60 ("iio: Add Freescale MMA8452Q 3-axis accelerometer driver")
Reported-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jonathan Cameron [Wed, 22 Jul 2020 15:50:40 +0000 (16:50 +0100)]
iio:accel:mma7455: Fix timestamp alignment and prevent data leak.
commit
7e5ac1f2206eda414f90c698fe1820dee873394d upstream.
One of a class of bugs pointed out by Lars in a recent review.
iio_push_to_buffers_with_timestamp assumes the buffer used is aligned
to the size of the timestamp (8 bytes). This is not guaranteed in
this driver which uses a 16 byte u8 array on the stack As Lars also noted
this anti pattern can involve a leak of data to userspace and that
indeed can happen here. We close both issues by moving to
a suitable structure in the iio_priv() data with alignment
ensured by use of an explicit c structure. This data is allocated
with kzalloc so no data can leak appart from previous readings.
The force alignment of ts is not strictly necessary in this particularly
case but does make the code less fragile.
Fixes:
a84ef0d181d9 ("iio: accel: add Freescale MMA7455L/MMA7456L 3-axis accelerometer driver")
Reported-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: <Stable@vger.kernel.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jonathan Cameron [Wed, 22 Jul 2020 15:50:37 +0000 (16:50 +0100)]
iio: accel: kxsd9: Fix alignment of local buffer.
commit
95ad67577de4ea08eb8e441394e698aa4addcc0b upstream.
iio_push_to_buffers_with_timestamp assumes 8 byte alignment which
is not guaranteed by an array of smaller elements.
Note that whilst in this particular case the alignment forcing
of the ts element is not strictly necessary it acts as good
documentation. Doing this where not necessary should cut
down on the number of cut and paste introduced errors elsewhere.
Fixes:
0427a106a98a ("iio: accel: kxsd9: Add triggered buffer handling")
Reported-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jonathan Cameron [Wed, 22 Jul 2020 15:50:45 +0000 (16:50 +0100)]
iio:light:max44000 Fix timestamp alignment and prevent data leak.
commit
523628852a5f5f34a15252b2634d0498d3cfb347 upstream.
One of a class of bugs pointed out by Lars in a recent review.
iio_push_to_buffers_with_timestamp assumes the buffer used is aligned
to the size of the timestamp (8 bytes). This is not guaranteed in
this driver which uses a 16 byte array of smaller elements on the stack.
As Lars also noted this anti pattern can involve a leak of data to
userspace and that indeed can happen here. We close both issues by
moving to a suitable structure in the iio_priv().
This data is allocated with kzalloc so no data can leak appart
from previous readings.
It is necessary to force the alignment of ts to avoid the padding
on x86_32 being different from 64 bit platorms (it alows for
4 bytes aligned 8 byte types.
Fixes:
06ad7ea10e2b ("max44000: Initial triggered buffer support")
Reported-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jonathan Cameron [Wed, 22 Jul 2020 15:50:49 +0000 (16:50 +0100)]
iio:magnetometer:ak8975 Fix alignment and data leak issues.
commit
02ad21cefbac4d89ac443866f25b90449527737b upstream.
One of a class of bugs pointed out by Lars in a recent review.
iio_push_to_buffers_with_timestamp assumes the buffer used is aligned
to the size of the timestamp (8 bytes). This is not guaranteed in
this driver which uses an array of smaller elements on the stack.
As Lars also noted this anti pattern can involve a leak of data to
userspace and that indeed can happen here. We close both issues by
moving to a suitable structure in the iio_priv() data.
This data is allocated with kzalloc so no data can leak apart from
previous readings.
The explicit alignment of ts is not necessary in this case as by
coincidence the padding will end up the same, however I consider
it to make the code less fragile and have included it.
Fixes:
bc11ca4a0b84 ("iio:magnetometer:ak8975: triggered buffer support")
Reported-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: Gregor Boirie <gregor.boirie@parrot.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sandhya Bankar [Sun, 25 Sep 2016 13:03:17 +0000 (18:33 +0530)]
drivers: iio: magnetometer: Fix sparse endianness warnings cast to restricted __be16
commit
69c72ec9c80bbd206c6fac73874d73e69cc623b4 upstream.
Fix the following sparse endianness warnings:
drivers/iio/magnetometer/ak8975.c:716:16: warning: cast to restricted __le16
drivers/iio/magnetometer/ak8975.c:837:19: warning: cast to restricted __le16
drivers/iio/magnetometer/ak8975.c:838:19: warning: cast to restricted __le16
drivers/iio/magnetometer/ak8975.c:839:19: warning: cast to restricted __le16
Signed-off-by: Sandhya Bankar <bankarsandhya512@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jonathan Cameron [Wed, 22 Jul 2020 15:50:56 +0000 (16:50 +0100)]
iio:adc:ti-adc081c Fix alignment and data leak issues
commit
54f82df2ba86e2a8e9cbf4036d192366e3905c89 upstream.
One of a class of bugs pointed out by Lars in a recent review.
iio_push_to_buffers_with_timestamp assumes the buffer used is aligned
to the size of the timestamp (8 bytes). This is not guaranteed in
this driver which uses an array of smaller elements on the stack.
As Lars also noted this anti pattern can involve a leak of data to
userspace and that indeed can happen here. We close both issues by
moving to a suitable structure in the iio_priv().
This data is allocated with kzalloc so no data can leak apart
from previous readings.
The eplicit alignment of ts is necessary to ensure correct padding
on x86_32 where s64 is only aligned to 4 bytes.
Fixes:
08e05d1fce5c ("ti-adc081c: Initial triggered buffer support")
Reported-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jonathan Cameron [Wed, 22 Jul 2020 15:51:02 +0000 (16:51 +0100)]
iio:adc:ina2xx Fix timestamp alignment issue.
commit
f8cd222feb82ecd82dcf610fcc15186f55f9c2b5 upstream.
One of a class of bugs pointed out by Lars in a recent review.
iio_push_to_buffers_with_timestamp assumes the buffer used is aligned
to the size of the timestamp (8 bytes). This is not guaranteed in
this driver which uses a 32 byte array of smaller elements on the stack.
As Lars also noted this anti pattern can involve a leak of data to
userspace and that indeed can happen here. We close both issues by
moving to a suitable structure in the iio_priv() data with alignment
explicitly requested. This data is allocated with kzalloc so no
data can leak apart from previous readings. The explicit alignment
isn't technically needed here, but it reduced fragility and avoids
cut and paste into drivers where it will be needed.
If we want this in older stables will need manual backport due to
driver reworks.
Fixes:
c43a102e67db ("iio: ina2xx: add support for TI INA2xx Power Monitors")
Reported-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Cc: Marc Titinger <mtitinger@baylibre.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jonathan Cameron [Wed, 22 Jul 2020 15:50:39 +0000 (16:50 +0100)]
iio:accel:bmc150-accel: Fix timestamp alignment and prevent data leak.
commit
a6f86f724394de3629da63fe5e1b7a4ab3396efe upstream.
One of a class of bugs pointed out by Lars in a recent review.
iio_push_to_buffers_with_timestamp assumes the buffer used is aligned
to the size of the timestamp (8 bytes). This is not guaranteed in
this driver which uses a 16 byte array of smaller elements on the stack.
As Lars also noted this anti pattern can involve a leak of data to
userspace and that indeed can happen here. We close both issues by moving
to a suitable structure in the iio_priv() data with alignment
ensured by use of an explicit c structure. This data is allocated
with kzalloc so no data can leak appart from previous readings.
Fixes tag is beyond some major refactoring so likely manual backporting
would be needed to get that far back.
Whilst the force alignment of the ts is not strictly necessary, it
does make the code less fragile.
Fixes:
3bbec9773389 ("iio: bmc150_accel: add support for hardware fifo")
Reported-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jonathan Cameron [Wed, 22 Jul 2020 15:50:48 +0000 (16:50 +0100)]
iio:light:ltr501 Fix timestamp alignment issue.
commit
2684d5003490df5398aeafe2592ba9d4a4653998 upstream.
One of a class of bugs pointed out by Lars in a recent review.
iio_push_to_buffers_with_timestamp assumes the buffer used is aligned
to the size of the timestamp (8 bytes). This is not guaranteed in
this driver which uses an array of smaller elements on the stack.
Here we use a structure on the stack. The driver already did an
explicit memset so no data leak was possible.
Forced alignment of ts is not strictly necessary but probably makes
the code slightly less fragile.
Note there has been some rework in this driver of the years, so no
way this will apply cleanly all the way back.
Fixes:
2690be905123 ("iio: Add Lite-On ltr501 ambient light / proximity sensor driver")
Reported-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Maxim Kochetkov [Mon, 3 Aug 2020 05:04:05 +0000 (08:04 +0300)]
iio: adc: ti-ads1015: fix conversion when CONFIG_PM is not set
commit
e71e6dbe96ac80ac2aebe71a6a942e7bd60e7596 upstream.
To stop conversion ads1015_set_power_state() function call unimplemented
function __pm_runtime_suspend() from pm_runtime_put_autosuspend()
if CONFIG_PM is not set.
In case of CONFIG_PM is not set: __pm_runtime_suspend() returns -ENOSYS,
so ads1015_read_raw() failed because ads1015_set_power_state() returns an
error.
If CONFIG_PM is disabled, there is no need to start/stop conversion.
Fix it by adding return 0 function variant if CONFIG_PM is not set.
Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru>
Fixes:
ecc24e72f437 ("iio: adc: Add TI ADS1015 ADC driver support")
Tested-by: Maxim Kiselev <bigunclemax@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Angelo Compagnucci [Tue, 1 Sep 2020 09:32:18 +0000 (11:32 +0200)]
iio: adc: mcp3422: fix locking on error path
[ Upstream commit
a139ffa40f0c24b753838b8ef3dcf6ad10eb7854 ]
Reading from the chip should be unlocked on error path else the lock
could never being released.
Fixes:
07914c84ba30 ("iio: adc: Add driver for Microchip MCP3422/3/4 high resolution ADC")
Fixes:
3f1093d83d71 ("iio: adc: mcp3422: fix locking scope")
Acked-by: Jonathan Cameron <jonathan.cameron@huawei.com>
Signed-off-by: Angelo Compagnucci <angelo.compagnucci@gmail.com>
Link: https://lore.kernel.org/r/20200901093218.1500845-1-angelo.compagnucci@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Angelo Compagnucci [Wed, 19 Aug 2020 07:55:25 +0000 (09:55 +0200)]
iio: adc: mcp3422: fix locking scope
commit
3f1093d83d7164e4705e4232ccf76da54adfda85 upstream.
Locking should be held for the entire reading sequence involving setting
the channel, waiting for the channel switch and reading from the
channel.
If not, reading from a channel can result mixing with the reading from
another channel.
Fixes:
07914c84ba30 ("iio: adc: Add driver for Microchip MCP3422/3/4 high resolution ADC")
Signed-off-by: Angelo Compagnucci <angelo.compagnucci@gmail.com>
Link: https://lore.kernel.org/r/20200819075525.1395248-1-angelo.compagnucci@gmail.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Leon Romanovsky [Fri, 4 Sep 2020 15:58:08 +0000 (18:58 +0300)]
gcov: Disable gcov build with GCC 10
[ Upstream commit
cfc905f158eaa099d6258031614d11869e7ef71c ]
GCOV built with GCC 10 doesn't initialize n_function variable. This
produces different kernel panics as was seen by Colin in Ubuntu and me
in FC 32.
As a workaround, let's disable GCOV build for broken GCC 10 version.
Link: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1891288
Link: https://lore.kernel.org/lkml/20200827133932.3338519-1-leon@kernel.org
Link: https://lore.kernel.org/lkml/CAHk-=whbijeSdSvx-Xcr0DPMj0BiwhJ+uiNnDSVZcr_h_kg7UA@mail.gmail.com/
Cc: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Rander Wang [Wed, 2 Sep 2020 15:42:18 +0000 (18:42 +0300)]
ALSA: hda: fix a runtime pm issue in SOF when integrated GPU is disabled
[ Upstream commit
13774d81f38538c5fa2924bdcdfa509155480fa6 ]
In snd_hdac_device_init pm_runtime_set_active is called to
increase child_count in parent device. But when it is failed
to build connection with GPU for one case that integrated
graphic gpu is disabled, snd_hdac_ext_bus_device_exit will be
invoked to clean up a HD-audio extended codec base device. At
this time the child_count of parent is not decreased, which
makes parent device can't get suspended.
This patch calls pm_runtime_set_suspended to decrease child_count
in parent device in snd_hdac_device_exit to match with
snd_hdac_device_init. pm_runtime_set_suspended can make sure that
it will not decrease child_count if the device is already suspended.
Signed-off-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20200902154218.1440441-1-kai.vehmanen@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Xie He [Fri, 28 Aug 2020 07:07:52 +0000 (00:07 -0700)]
drivers/net/wan/hdlc_cisco: Add hard_header_len
[ Upstream commit
1a545ebe380bf4c1433e3c136e35a77764fda5ad ]
This driver didn't set hard_header_len. This patch sets hard_header_len
for it according to its header_ops->create function.
This driver's header_ops->create function (cisco_hard_header) creates
a header of (struct hdlc_header), so hard_header_len should be set to
sizeof(struct hdlc_header).
Cc: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Acked-by: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Vineet Gupta [Mon, 24 Aug 2020 19:10:33 +0000 (12:10 -0700)]
irqchip/eznps: Fix build error for !ARC700 builds
[ Upstream commit
89d29997f103d08264b0685796b420d911658b96 ]
eznps driver is supposed to be platform independent however it ends up
including stuff from inside arch/arc headers leading to rand config
build errors.
The quick hack to fix this (proper fix is too much chrun for non active
user-base) is to add following to nps platform agnostic header.
- copy AUX_IENABLE from arch/arc header
- move CTOP_AUX_IACK from arch/arc/plat-eznps/*/**
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://lkml.kernel.org/r/20200824095831.5lpkmkafelnvlpi2@linutronix.de
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Darrick J. Wong [Wed, 26 Aug 2020 21:12:18 +0000 (14:12 -0700)]
xfs: initialize the shortform attr header padding entry
[ Upstream commit
125eac243806e021f33a1fdea3687eccbb9f7636 ]
Don't leak kernel memory contents into the shortform attr fork.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Xie He [Wed, 26 Aug 2020 03:03:53 +0000 (20:03 -0700)]
drivers/net/wan/lapbether: Set network_header before transmitting
[ Upstream commit
91244d108441013b7367b3b4dcc6869998676473 ]
Set the skb's network_header before it is passed to the underlying
Ethernet device for transmission.
This patch fixes the following issue:
When we use this driver with AF_PACKET sockets, there would be error
messages of:
protocol 0805 is buggy, dev (Ethernet interface name)
printed in the system "dmesg" log.
This is because skbs passed down to the Ethernet device for transmission
don't have their network_header properly set, and the dev_queue_xmit_nit
function in net/core/dev.c complains about this.
Reason of setting the network_header to this place (at the end of the
Ethernet header, and at the beginning of the Ethernet payload):
Because when this driver receives an skb from the Ethernet device, the
network_header is also set at this place.
Cc: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Mohan Kumar [Tue, 25 Aug 2020 05:24:14 +0000 (10:54 +0530)]
ALSA: hda: Fix 2 channel swapping for Tegra
[ Upstream commit
216116eae43963c662eb84729507bad95214ca6b ]
The Tegra HDA codec HW implementation has an issue related to not
swapping the 2 channel Audio Sample Packet(ASP) channel mapping.
Whatever the FL and FR mapping specified the left channel always
comes out of left speaker and right channel on right speaker. So
add condition to disallow the swapping of FL,FR during the playback.
Signed-off-by: Mohan Kumar <mkumard@nvidia.com>
Acked-by: Sameer Pujar <spujar@nvidia.com>
Link: https://lore.kernel.org/r/20200825052415.20626-2-mkumard@nvidia.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Dinghao Liu [Sun, 23 Aug 2020 11:29:35 +0000 (19:29 +0800)]
firestream: Fix memleak in fs_open
[ Upstream commit
15ac5cdafb9202424206dc5bd376437a358963f9 ]
When make_rate() fails, vcc should be freed just
like other error paths in fs_open().
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Dinghao Liu [Sun, 23 Aug 2020 07:23:43 +0000 (15:23 +0800)]
NFC: st95hf: Fix memleak in st95hf_in_send_cmd
[ Upstream commit
f97c04c316d8fea16dca449fdfbe101fbdfee6a2 ]
When down_killable() fails, skb_resp should be freed
just like when st95hf_spi_send() fails.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Xie He [Fri, 21 Aug 2020 21:26:59 +0000 (14:26 -0700)]
drivers/net/wan/lapbether: Added needed_tailroom
[ Upstream commit
1ee39c1448c4e0d480c5b390e2db1987561fb5c2 ]
The underlying Ethernet device may request necessary tailroom to be
allocated by setting needed_tailroom. This driver should also set
needed_tailroom to request the tailroom needed by the underlying
Ethernet device to be allocated.
Cc: Willem de Bruijn <willemdebruijn.kernel@gmail.com>
Cc: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Luo Jiaxing [Wed, 26 Aug 2020 07:24:26 +0000 (15:24 +0800)]
scsi: libsas: Set data_dir as DMA_NONE if libata marks qc as NODATA
[ Upstream commit
53de092f47ff40e8d4d78d590d95819d391bf2e0 ]
It was discovered that sdparm will fail when attempting to disable write
cache on a SATA disk connected via libsas.
In the ATA command set the write cache state is controlled through the SET
FEATURES operation. This is roughly corresponds to MODE SELECT in SCSI and
the latter command is what is used in the SCSI-ATA translation layer. A
subtle difference is that a MODE SELECT carries data whereas SET FEATURES
is defined as a non-data command in ATA.
Set the DMA data direction to DMA_NONE if the requested ATA command is
identified as non-data.
[mkp: commit desc]
Fixes:
fa1c1e8f1ece ("[SCSI] Add SATA support to libsas")
Link: https://lore.kernel.org/r/1598426666-54544-1-git-send-email-luojiaxing@huawei.com
Reviewed-by: John Garry <john.garry@huawei.com>
Reviewed-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Kamal Heib [Sun, 5 Jul 2020 10:43:10 +0000 (13:43 +0300)]
RDMA/rxe: Drop pointless checks in rxe_init_ports
[ Upstream commit
6112ef62826e91afbae5446d5d47b38e25f47e3f ]
Both pkey_tbl_len and gid_tbl_len are set in rxe_init_port_param() - so no
need to check if they aren't set.
Fixes:
8700e3e7c485 ("Soft RoCE driver")
Link: https://lore.kernel.org/r/20200705104313.283034-2-kamalheib1@gmail.com
Signed-off-by: Kamal Heib <kamalheib1@gmail.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Dinghao Liu [Wed, 19 Aug 2020 07:56:32 +0000 (15:56 +0800)]
RDMA/rxe: Fix memleak in rxe_mem_init_user
[ Upstream commit
e3ddd6067ee62f6e76ebcf61ff08b2c729ae412b ]
When page_address() fails, umem should be freed just like when
rxe_mem_alloc() fails.
Fixes:
8700e3e7c485 ("Soft RoCE driver")
Link: https://lore.kernel.org/r/20200819075632.22285-1-dinghao.liu@zju.edu.cn
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Dinh Nguyen [Fri, 31 Jul 2020 15:26:40 +0000 (10:26 -0500)]
ARM: dts: socfpga: fix register entry for timer3 on Arria10
[ Upstream commit
0ff5a4812be4ebd4782bbb555d369636eea164f7 ]
Fixes the register address for the timer3 entry on Arria10.
Fixes:
475dc86d08de4 ("arm: dts: socfpga: Add a base DTSI for Altera's Arria10 SOC")
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Greg Kroah-Hartman [Sat, 12 Sep 2020 09:47:40 +0000 (11:47 +0200)]
Linux 4.9.236
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Shuah Khan <skhan@linuxfoundation.org>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Linux Kernel Functional Testing <lkft@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jakub Kicinski [Wed, 26 Aug 2020 19:40:06 +0000 (12:40 -0700)]
net: disable netpoll on fresh napis
[ Upstream commit
96e97bc07e90f175a8980a22827faf702ca4cb30 ]
napi_disable() makes sure to set the NAPI_STATE_NPSVC bit to prevent
netpoll from accessing rings before init is complete. However, the
same is not done for fresh napi instances in netif_napi_add(),
even though we expect NAPI instances to be added as disabled.
This causes crashes during driver reconfiguration (enabling XDP,
changing the channel count) - if there is any printk() after
netif_napi_add() but before napi_enable().
To ensure memory ordering is correct we need to use RCU accessors.
Reported-by: Rob Sherwood <rsher@fb.com>
Fixes:
2d8bff12699a ("netpoll: Close race condition between poll_one_napi and napi_disable")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Xin Long [Fri, 21 Aug 2020 06:59:38 +0000 (14:59 +0800)]
sctp: not disable bh in the whole sctp_get_port_local()
[ Upstream commit
3106ecb43a05dc3e009779764b9da245a5d082de ]
With disabling bh in the whole sctp_get_port_local(), when
snum == 0 and too many ports have been used, the do-while
loop will take the cpu for a long time and cause cpu stuck:
[ ] watchdog: BUG: soft lockup - CPU#11 stuck for 22s!
[ ] RIP: 0010:native_queued_spin_lock_slowpath+0x4de/0x940
[ ] Call Trace:
[ ] _raw_spin_lock+0xc1/0xd0
[ ] sctp_get_port_local+0x527/0x650 [sctp]
[ ] sctp_do_bind+0x208/0x5e0 [sctp]
[ ] sctp_autobind+0x165/0x1e0 [sctp]
[ ] sctp_connect_new_asoc+0x355/0x480 [sctp]
[ ] __sctp_connect+0x360/0xb10 [sctp]
There's no need to disable bh in the whole function of
sctp_get_port_local. So fix this cpu stuck by removing
local_bh_disable() called at the beginning, and using
spin_lock_bh() instead.
The same thing was actually done for inet_csk_get_port() in
Commit
ea8add2b1903 ("tcp/dccp: better use of ephemeral
ports in bind()").
Thanks to Marcelo for pointing the buggy code out.
v1->v2:
- use cond_resched() to yield cpu to other tasks if needed,
as Eric noticed.
Fixes:
1da177e4c3f4 ("Linux-2.6.12-rc2")
Reported-by: Ying Xu <yinxu@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kamil Lorenc [Tue, 1 Sep 2020 08:57:38 +0000 (10:57 +0200)]
net: usb: dm9601: Add USB ID of Keenetic Plus DSL
[ Upstream commit
a609d0259183a841621f252e067f40f8cc25d6f6 ]
Keenetic Plus DSL is a xDSL modem that uses dm9620 as its USB interface.
Signed-off-by: Kamil Lorenc <kamil@re-ws.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Paul Moore [Fri, 21 Aug 2020 20:34:52 +0000 (16:34 -0400)]
netlabel: fix problems with mapping removal
[ Upstream commit
d3b990b7f327e2afa98006e7666fb8ada8ed8683 ]
This patch fixes two main problems seen when removing NetLabel
mappings: memory leaks and potentially extra audit noise.
The memory leaks are caused by not properly free'ing the mapping's
address selector struct when free'ing the entire entry as well as
not properly cleaning up a temporary mapping entry when adding new
address selectors to an existing entry. This patch fixes both these
problems such that kmemleak reports no NetLabel associated leaks
after running the SELinux test suite.
The potentially extra audit noise was caused by the auditing code in
netlbl_domhsh_remove_entry() being called regardless of the entry's
validity. If another thread had already marked the entry as invalid,
but not removed/free'd it from the list of mappings, then it was
possible that an additional mapping removal audit record would be
generated. This patch fixes this by returning early from the removal
function when the entry was previously marked invalid. This change
also had the side benefit of improving the code by decreasing the
indentation level of large chunk of code by one (accounting for most
of the diffstat).
Fixes:
63c416887437 ("netlabel: Add network address selectors to the NetLabel/LSM domain mapping")
Reported-by: Stephen Smalley <stephen.smalley.work@gmail.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jakub Kicinski [Wed, 26 Aug 2020 19:40:07 +0000 (12:40 -0700)]
bnxt: don't enable NAPI until rings are ready
commit
96ecdcc992eb7f468b2cf829b0f5408a1fad4668 upstream.
Netpoll can try to poll napi as soon as napi_enable() is called.
It crashes trying to access a doorbell which is still NULL:
BUG: kernel NULL pointer dereference, address:
0000000000000000
CPU: 59 PID: 6039 Comm: ethtool Kdump: loaded Tainted: G S 5.9.0-rc1-00469-g5fd99b5d9950-dirty #26
RIP: 0010:bnxt_poll+0x121/0x1c0
Code: c4 20 44 89 e0 5b 5d 41 5c 41 5d 41 5e 41 5f c3 41 8b 86 a0 01 00 00 41 23 85 18 01 00 00 49 8b 96 a8 01 00 00 0d 00 00 00 24 <89> 02
41 f6 45 77 02 74 cb 49 8b ae d8 01 00 00 31 c0 c7 44 24 1a
netpoll_poll_dev+0xbd/0x1a0
__netpoll_send_skb+0x1b2/0x210
netpoll_send_udp+0x2c9/0x406
write_ext_msg+0x1d7/0x1f0
console_unlock+0x23c/0x520
vprintk_emit+0xe0/0x1d0
printk+0x58/0x6f
x86_vector_activate.cold+0xf/0x46
__irq_domain_activate_irq+0x50/0x80
__irq_domain_activate_irq+0x32/0x80
__irq_domain_activate_irq+0x32/0x80
irq_domain_activate_irq+0x25/0x40
__setup_irq+0x2d2/0x700
request_threaded_irq+0xfb/0x160
__bnxt_open_nic+0x3b1/0x750
bnxt_open_nic+0x19/0x30
ethtool_set_channels+0x1ac/0x220
dev_ethtool+0x11ba/0x2240
dev_ioctl+0x1cf/0x390
sock_do_ioctl+0x95/0x130
Reported-by: Rob Sherwood <rsher@fb.com>
Fixes:
c0c050c58d84 ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Shung-Hsi Yu [Mon, 31 Aug 2020 14:37:09 +0000 (22:37 +0800)]
net: ethernet: mlx4: Fix memory allocation in mlx4_buddy_init()
commit
cbedcb044e9cc4e14bbe6658111224bb923094f4 upstream.
On machines with much memory (> 2 TByte) and log_mtts_per_seg == 0, a
max_order of 31 will be passed to mlx_buddy_init(), which results in
s = BITS_TO_LONGS(1 << 31) becoming a negative value, leading to
kvmalloc_array() failure when it is converted to size_t.
mlx4_core 0000:b1:00.0: Failed to initialize memory region table, aborting
mlx4_core: probe of 0000:b1:00.0 failed with error -12
Fix this issue by changing the left shifting operand from a signed literal to
an unsigned one.
Fixes:
225c7b1feef1 ("IB/mlx4: Add a driver Mellanox ConnectX InfiniBand adapters")
Signed-off-by: Shung-Hsi Yu <shung-hsi.yu@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Max Staudt [Thu, 27 Aug 2020 15:49:00 +0000 (17:49 +0200)]
affs: fix basic permission bits to actually work
[ Upstream commit
d3a84a8d0dde4e26bc084b36ffcbdc5932ac85e2 ]
The basic permission bits (protection bits in AmigaOS) have been broken
in Linux' AFFS - it would only set bits, but never delete them.
Also, contrary to the documentation, the Archived bit was not handled.
Let's fix this for good, and set the bits such that Linux and classic
AmigaOS can coexist in the most peaceful manner.
Also, update the documentation to represent the current state of things.
Fixes:
1da177e4c3f4 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org
Signed-off-by: Max Staudt <max@enpas.org>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Fabian Frederick [Mon, 27 Feb 2017 22:27:52 +0000 (14:27 -0800)]
fs/affs: use octal for permissions
[ Upstream commit
1bafd6f164d9ec9bf2fa9829051fbeb36342be0b ]
According to commit
f90774e1fd27 ("checkpatch: look for symbolic
permissions and suggest octal instead")
Link: http://lkml.kernel.org/r/20170109191208.6085-5-fabf@skynet.be
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Takashi Sakamoto [Sun, 23 Aug 2020 07:55:37 +0000 (16:55 +0900)]
ALSA; firewire-tascam: exclude Tascam FE-8 from detection
Tascam FE-8 is known to support communication by asynchronous transaction
only. The support can be implemented in userspace application and
snd-firewire-ctl-services project has the support. However, ALSA
firewire-tascam driver is bound to the model.
This commit changes device entries so that the model is excluded. In a
commit
53b3ffee7885 ("ALSA: firewire-tascam: change device probing
processing"), I addressed to the concern that version field in
configuration differs depending on installed firmware. However, as long
as I checked, the version number is fixed. It's safe to return version
number back to modalias.
Fixes:
53b3ffee7885 ("ALSA: firewire-tascam: change device probing processing")
Cc: <stable@vger.kernel.org> # 4.4+
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20200823075537.56255-1-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Himadri Pandya [Thu, 27 Aug 2020 06:53:55 +0000 (12:23 +0530)]
net: usb: Fix uninit-was-stored issue in asix_read_phy_addr()
commit
a092b7233f0e000cc6f2c71a49e2ecc6f917a5fc upstream.
The buffer size is 2 Bytes and we expect to receive the same amount of
data. But sometimes we receive less data and run into uninit-was-stored
issue upon read. Hence modify the error check on the return value to match
with the buffer size as a prevention.
Reported-and-tested by: syzbot+
a7e220df5a81d1ab400e@syzkaller.appspotmail.com
Signed-off-by: Himadri Pandya <himadrispandya@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johannes Berg [Wed, 19 Aug 2020 08:46:48 +0000 (10:46 +0200)]
cfg80211: regulatory: reject invalid hints
commit
47caf685a6854593348f216e0b489b71c10cbe03 upstream.
Reject invalid hints early in order to not cause a kernel
WARN later if they're restored to or similar.
Reported-by: syzbot+d451401ffd00a60677ee@syzkaller.appspotmail.com
Link: https://syzkaller.appspot.com/bug?extid=d451401ffd00a60677ee
Link: https://lore.kernel.org/r/20200819084648.13956-1-johannes@sipsolutions.net
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Muchun Song [Fri, 4 Sep 2020 23:36:13 +0000 (16:36 -0700)]
mm/hugetlb: fix a race between hugetlb sysctl handlers
commit
17743798d81238ab13050e8e2833699b54e15467 upstream.
There is a race between the assignment of `table->data` and write value
to the pointer of `table->data` in the __do_proc_doulongvec_minmax() on
the other thread.
CPU0: CPU1:
proc_sys_write
hugetlb_sysctl_handler proc_sys_call_handler
hugetlb_sysctl_handler_common hugetlb_sysctl_handler
table->data = &tmp; hugetlb_sysctl_handler_common
table->data = &tmp;
proc_doulongvec_minmax
do_proc_doulongvec_minmax sysctl_head_finish
__do_proc_doulongvec_minmax unuse_table
i = table->data;
*i = val; // corrupt CPU1's stack
Fix this by duplicating the `table`, and only update the duplicate of
it. And introduce a helper of proc_hugetlb_doulongvec_minmax() to
simplify the code.
The following oops was seen:
BUG: kernel NULL pointer dereference, address:
0000000000000000
#PF: supervisor instruction fetch in kernel mode
#PF: error_code(0x0010) - not-present page
Code: Bad RIP value.
...
Call Trace:
? set_max_huge_pages+0x3da/0x4f0
? alloc_pool_huge_page+0x150/0x150
? proc_doulongvec_minmax+0x46/0x60
? hugetlb_sysctl_handler_common+0x1c7/0x200
? nr_hugepages_store+0x20/0x20
? copy_fd_bitmaps+0x170/0x170
? hugetlb_sysctl_handler+0x1e/0x20
? proc_sys_call_handler+0x2f1/0x300
? unregister_sysctl_table+0xb0/0xb0
? __fd_install+0x78/0x100
? proc_sys_write+0x14/0x20
? __vfs_write+0x4d/0x90
? vfs_write+0xef/0x240
? ksys_write+0xc0/0x160
? __ia32_sys_read+0x50/0x50
? __close_fd+0x129/0x150
? __x64_sys_write+0x43/0x50
? do_syscall_64+0x6c/0x200
? entry_SYSCALL_64_after_hwframe+0x44/0xa9
Fixes:
e5ff215941d5 ("hugetlb: multiple hstates for multiple page sizes")
Signed-off-by: Muchun Song <songmuchun@bytedance.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Andi Kleen <ak@linux.intel.com>
Link: http://lkml.kernel.org/r/20200828031146.43035-1-songmuchun@bytedance.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mrinal Pandey [Fri, 4 Sep 2020 23:35:52 +0000 (16:35 -0700)]
checkpatch: fix the usage of capture group ( ... )
commit
13e45417cedbfc44b1926124b1846f5ee8c6ba4a upstream.
The usage of "capture group (...)" in the immediate condition after `&&`
results in `$1` being uninitialized. This issues a warning "Use of
uninitialized value $1 in regexp compilation at ./scripts/checkpatch.pl
line 2638".
I noticed this bug while running checkpatch on the set of commits from
v5.7 to v5.8-rc1 of the kernel on the commits with a diff content in
their commit message.
This bug was introduced in the script by commit
e518e9a59ec3
("checkpatch: emit an error when there's a diff in a changelog"). It
has been in the script since then.
The author intended to store the match made by capture group in variable
`$1`. This should have contained the name of the file as `[\w/]+`
matched. However, this couldn't be accomplished due to usage of capture
group and `$1` in the same regular expression.
Fix this by placing the capture group in the condition before `&&`.
Thus, `$1` can be initialized to the text that capture group matches
thereby setting it to the desired and required value.
Fixes:
e518e9a59ec3 ("checkpatch: emit an error when there's a diff in a changelog")
Signed-off-by: Mrinal Pandey <mrinalmni@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Tested-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Reviewed-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Cc: Joe Perches <joe@perches.com>
Link: https://lkml.kernel.org/r/20200714032352.f476hanaj2dlmiot@mrinalpandey
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alex Williamson [Thu, 25 Jun 2020 17:04:23 +0000 (11:04 -0600)]
vfio/pci: Fix SR-IOV VF handling with MMIO blocking
commit
ebfa440ce38b7e2e04c3124aa89c8a9f4094cf21 upstream.
SR-IOV VFs do not implement the memory enable bit of the command
register, therefore this bit is not set in config space after
pci_enable_device(). This leads to an unintended difference
between PF and VF in hand-off state to the user. We can correct
this by setting the initial value of the memory enable bit in our
virtualized config space. There's really no need however to
ever fault a user on a VF though as this would only indicate an
error in the user's management of the enable bit, versus a PF
where the same access could trigger hardware faults.
Fixes:
abafbc551fdd ("vfio-pci: Invalidate mmaps and block MMIO access on disabled memory")
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tim Froidcoeur [Tue, 11 Aug 2020 18:33:24 +0000 (20:33 +0200)]
net: initialize fastreuse on inet_inherit_port
commit
d76f3351cea2d927fdf70dd7c06898235035e84e upstream.
In the case of TPROXY, bind_conflict optimizations for SO_REUSEADDR or
SO_REUSEPORT are broken, possibly resulting in O(n) instead of O(1) bind
behaviour or in the incorrect reuse of a bind.
the kernel keeps track for each bind_bucket if all sockets in the
bind_bucket support SO_REUSEADDR or SO_REUSEPORT in two fastreuse flags.
These flags allow skipping the costly bind_conflict check when possible
(meaning when all sockets have the proper SO_REUSE option).
For every socket added to a bind_bucket, these flags need to be updated.
As soon as a socket that does not support reuse is added, the flag is
set to false and will never go back to true, unless the bind_bucket is
deleted.
Note that there is no mechanism to re-evaluate these flags when a socket
is removed (this might make sense when removing a socket that would not
allow reuse; this leaves room for a future patch).
For this optimization to work, it is mandatory that these flags are
properly initialized and updated.
When a child socket is created from a listen socket in
__inet_inherit_port, the TPROXY case could create a new bind bucket
without properly initializing these flags, thus preventing the
optimization to work. Alternatively, a socket not allowing reuse could
be added to an existing bind bucket without updating the flags, causing
bind_conflict to never be called as it should.
Call inet_csk_update_fastreuse when __inet_inherit_port decides to create
a new bind_bucket or use a different bind_bucket than the one of the
listen socket.
Fixes:
093d282321da ("tproxy: fix hash locking issue when using port redirection in __inet_inherit_port()")
Acked-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Tim Froidcoeur <tim.froidcoeur@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Tim Froidcoeur <tim.froidcoeur@tessares.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tim Froidcoeur [Tue, 11 Aug 2020 18:33:23 +0000 (20:33 +0200)]
net: refactor bind_bucket fastreuse into helper
commit
62ffc589abb176821662efc4525ee4ac0b9c3894 upstream.
Refactor the fastreuse update code in inet_csk_get_port into a small
helper function that can be called from other places.
Acked-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Tim Froidcoeur <tim.froidcoeur@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Tim Froidcoeur <tim.froidcoeur@tessares.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
James Morse [Fri, 4 Sep 2020 11:29:00 +0000 (12:29 +0100)]
KVM: arm64: Set HCR_EL2.PTW to prevent AT taking synchronous exception
commit
71a7f8cb1ca4ca7214a700b1243626759b6c11d4 upstream.
AT instructions do a translation table walk and return the result, or
the fault in PAR_EL1. KVM uses these to find the IPA when the value is
not provided by the CPU in HPFAR_EL1.
If a translation table walk causes an external abort it is taken as an
exception, even if it was due to an AT instruction. (DDI0487F.a's D5.2.11
"Synchronous faults generated by address translation instructions")
While we previously made KVM resilient to exceptions taken due to AT
instructions, the device access causes mismatched attributes, and may
occur speculatively. Prevent this, by forbidding a walk through memory
described as device at stage2. Now such AT instructions will report a
stage2 fault.
Such a fault will cause KVM to restart the guest. If the AT instructions
always walk the page tables, but guest execution uses the translation cached
in the TLB, the guest can't make forward progress until the TLB entry is
evicted. This isn't a problem, as since commit
5dcd0fdbb492 ("KVM: arm64:
Defer guest entry when an asynchronous exception is pending"), KVM will
return to the host to process IRQs allowing the rest of the system to keep
running.
Cc: stable@vger.kernel.org # v4.9
Signed-off-by: James Morse <james.morse@arm.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
James Morse [Fri, 4 Sep 2020 11:28:59 +0000 (12:28 +0100)]
KVM: arm64: Survive synchronous exceptions caused by AT instructions
commit
88a84ccccb3966bcc3f309cdb76092a9892c0260 upstream.
KVM doesn't expect any synchronous exceptions when executing, any such
exception leads to a panic(). AT instructions access the guest page
tables, and can cause a synchronous external abort to be taken.
The arm-arm is unclear on what should happen if the guest has configured
the hardware update of the access-flag, and a memory type in TCR_EL1 that
does not support atomic operations. B2.2.6 "Possible implementation
restrictions on using atomic instructions" from DDI0487F.a lists
synchronous external abort as a possible behaviour of atomic instructions
that target memory that isn't writeback cacheable, but the page table
walker may behave differently.
Make KVM robust to synchronous exceptions caused by AT instructions.
Add a get_user() style helper for AT instructions that returns -EFAULT
if an exception was generated.
While KVM's version of the exception table mixes synchronous and
asynchronous exceptions, only one of these can occur at each location.
Re-enter the guest when the AT instructions take an exception on the
assumption the guest will take the same exception. This isn't guaranteed
to make forward progress, as the AT instructions may always walk the page
tables, but guest execution may use the translation cached in the TLB.
This isn't a problem, as since commit
5dcd0fdbb492 ("KVM: arm64: Defer guest
entry when an asynchronous exception is pending"), KVM will return to the
host to process IRQs allowing the rest of the system to keep running.
Cc: stable@vger.kernel.org # v4.9
Signed-off-by: James Morse <james.morse@arm.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
James Morse [Fri, 4 Sep 2020 11:28:58 +0000 (12:28 +0100)]
KVM: arm64: Defer guest entry when an asynchronous exception is pending
commit
5dcd0fdbb492d49dac6bf21c436dfcb5ded0a895 upstream.
SError that occur during world-switch's entry to the guest will be
accounted to the guest, as the exception is masked until we enter the
guest... but we want to attribute the SError as precisely as possible.
Reading DISR_EL1 before guest entry requires free registers, and using
ESB+DISR_EL1 to consume and read back the ESR would leave KVM holding
a host SError... We would rather leave the SError pending and let the
host take it once we exit world-switch. To do this, we need to defer
guest-entry if an SError is pending.
Read the ISR to see if SError (or an IRQ) is pending. If so fake an
exit. Place this check between __guest_enter()'s save of the host
registers, and restore of the guest's. SError that occur between
here and the eret into the guest must have affected the guest's
registers, which we can naturally attribute to the guest.
The dsb is needed to ensure any previous writes have been done before
we read ISR_EL1. On systems without the v8.2 RAS extensions this
doesn't give us anything as we can't contain errors, and the ESR bits
to describe the severity are all implementation-defined. Replace
this with a nop for these systems.
v4.9-backport: as this kernel version doesn't have the RAS support at
all, remove the RAS alternative.
Cc: stable@vger.kernel.org # v4.9
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
[ James: Removed v8.2 RAS related barriers ]
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
James Morse [Fri, 4 Sep 2020 11:28:57 +0000 (12:28 +0100)]
KVM: arm64: Add kvm_extable for vaxorcism code
commit
e9ee186bb735bfc17fa81dbc9aebf268aee5b41e upstream.
KVM has a one instruction window where it will allow an SError exception
to be consumed by the hypervisor without treating it as a hypervisor bug.
This is used to consume asynchronous external abort that were caused by
the guest.
As we are about to add another location that survives unexpected exceptions,
generalise this code to make it behave like the host's extable.
KVM's version has to be mapped to EL2 to be accessible on nVHE systems.
The SError vaxorcism code is a one instruction window, so has two entries
in the extable. Because the KVM code is copied for VHE and nVHE, we end up
with four entries, half of which correspond with code that isn't mapped.
Cc: stable@vger.kernel.org # v4.9
Signed-off-by: James Morse <james.morse@arm.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alex Williamson [Wed, 22 Apr 2020 19:48:11 +0000 (13:48 -0600)]
vfio-pci: Invalidate mmaps and block MMIO access on disabled memory
commit
abafbc551fddede3e0a08dee1dcde08fc0eb8476 upstream.
Accessing the disabled memory space of a PCI device would typically
result in a master abort response on conventional PCI, or an
unsupported request on PCI express. The user would generally see
these as a -1 response for the read return data and the write would be
silently discarded, possibly with an uncorrected, non-fatal AER error
triggered on the host. Some systems however take it upon themselves
to bring down the entire system when they see something that might
indicate a loss of data, such as this discarded write to a disabled
memory space.
To avoid this, we want to try to block the user from accessing memory
spaces while they're disabled. We start with a semaphore around the
memory enable bit, where writers modify the memory enable state and
must be serialized, while readers make use of the memory region and
can access in parallel. Writers include both direct manipulation via
the command register, as well as any reset path where the internal
mechanics of the reset may both explicitly and implicitly disable
memory access, and manipulation of the MSI-X configuration, where the
MSI-X vector table resides in MMIO space of the device. Readers
include the read and write file ops to access the vfio device fd
offsets as well as memory mapped access. In the latter case, we make
use of our new vma list support to zap, or invalidate, those memory
mappings in order to force them to be faulted back in on access.
Our semaphore usage will stall user access to MMIO spaces across
internal operations like reset, but the user might experience new
behavior when trying to access the MMIO space while disabled via the
PCI command register. Access via read or write while disabled will
return -EIO and access via memory maps will result in a SIGBUS. This
is expected to be compatible with known use cases and potentially
provides better error handling capabilities than present in the
hardware, while avoiding the more readily accessible and severe
platform error responses that might otherwise occur.
Fixes: CVE-2020-12888
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
[Ajay: Regenerated the patch for v4.9]
Signed-off-by: Ajay Kaher <akaher@vmware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alex Williamson [Tue, 28 Apr 2020 19:12:20 +0000 (13:12 -0600)]
vfio-pci: Fault mmaps to enable vma tracking
commit
11c4cd07ba111a09f49625f9e4c851d83daf0a22 upstream.
Rather than calling remap_pfn_range() when a region is mmap'd, setup
a vm_ops handler to support dynamic faulting of the range on access.
This allows us to manage a list of vmas actively mapping the area that
we can later use to invalidate those mappings. The open callback
invalidates the vma range so that all tracking is inserted in the
fault handler and removed in the close handler.
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
[Ajay: Regenerated the patch for v4.9]
Signed-off-by: Ajay Kaher <akaher@vmware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alex Williamson [Tue, 28 Apr 2020 23:02:24 +0000 (17:02 -0600)]
vfio/type1: Support faulting PFNMAP vmas
commit
41311242221e3482b20bfed10fa4d9db98d87016 upstream.
With conversion to follow_pfn(), DMA mapping a PFNMAP range depends on
the range being faulted into the vma. Add support to manually provide
that, in the same way as done on KVM with hva_to_pfn_remapped().
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
[Ajay: Regenerated the patch for v4.9]
Signed-off-by: Ajay Kaher <akaher@vmware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eugeniu Rosca [Fri, 4 Sep 2020 23:35:30 +0000 (16:35 -0700)]
mm: slub: fix conversion of freelist_corrupted()
commit
dc07a728d49cf025f5da2c31add438d839d076c0 upstream.
Commit
52f23478081ae0 ("mm/slub.c: fix corrupted freechain in
deactivate_slab()") suffered an update when picked up from LKML [1].
Specifically, relocating 'freelist = NULL' into 'freelist_corrupted()'
created a no-op statement. Fix it by sticking to the behavior intended
in the original patch [1]. In addition, make freelist_corrupted()
immune to passing NULL instead of &freelist.
The issue has been spotted via static analysis and code review.
[1] https://lore.kernel.org/linux-mm/
20200331031450.12182-1-dongli.zhang@oracle.com/
Fixes:
52f23478081ae0 ("mm/slub.c: fix corrupted freechain in deactivate_slab()")
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Dongli Zhang <dongli.zhang@oracle.com>
Cc: Joe Jin <joe.jin@oracle.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: <stable@vger.kernel.org>
Link: https://lkml.kernel.org/r/20200824130643.10291-1-erosca@de.adit-jv.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ye Bin [Tue, 1 Sep 2020 06:25:43 +0000 (14:25 +0800)]
dm thin metadata: Avoid returning cmd->bm wild pointer on error
commit
219403d7e56f9b716ad80ab87db85d29547ee73e upstream.
Maybe __create_persistent_data_objects() caller will use PTR_ERR as a
pointer, it will lead to some strange things.
Signed-off-by: Ye Bin <yebin10@huawei.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ye Bin [Tue, 1 Sep 2020 06:25:42 +0000 (14:25 +0800)]
dm cache metadata: Avoid returning cmd->bm wild pointer on error
commit
d16ff19e69ab57e08bf908faaacbceaf660249de upstream.
Maybe __create_persistent_data_objects() caller will use PTR_ERR as a
pointer, it will lead to some strange things.
Signed-off-by: Ye Bin <yebin10@huawei.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tejun Heo [Wed, 2 Sep 2020 16:32:45 +0000 (12:32 -0400)]
libata: implement ATA_HORKAGE_MAX_TRIM_128M and apply to Sandisks
commit
3b5455636fe26ea21b4189d135a424a6da016418 upstream.
All three generations of Sandisk SSDs lock up hard intermittently.
Experiments showed that disabling NCQ lowered the failure rate significantly
and the kernel has been disabling NCQ for some models of SD7's and 8's,
which is obviously undesirable.
Karthik worked with Sandisk to root cause the hard lockups to trim commands
larger than 128M. This patch implements ATA_HORKAGE_MAX_TRIM_128M which
limits max trim size to 128M and applies it to all three generations of
Sandisk SSDs.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Karthik Shivaram <karthikgs@fb.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bart Van Assche [Wed, 14 Mar 2018 22:48:06 +0000 (15:48 -0700)]
block: Move SECTOR_SIZE and SECTOR_SHIFT definitions into <linux/blkdev.h>
commit
233bde21aa43516baa013ef7ac33f3427056db3e upstream.
It happens often while I'm preparing a patch for a block driver that
I'm wondering: is a definition of SECTOR_SIZE and/or SECTOR_SHIFT
available for this driver? Do I have to introduce definitions of these
constants before I can use these constants? To avoid this confusion,
move the existing definitions of SECTOR_SIZE and SECTOR_SHIFT into the
<linux/blkdev.h> header file such that these become available for all
block drivers. Make the SECTOR_SIZE definition in the uapi msdos_fs.h
header file conditional to avoid that including that header file after
<linux/blkdev.h> causes the compiler to complain about a SECTOR_SIZE
redefinition.
Note: the SECTOR_SIZE / SECTOR_SHIFT / SECTOR_BITS definitions have
not been removed from uapi header files nor from NAND drivers in
which these constants are used for another purpose than converting
block layer offsets and sizes into a number of sectors.
Cc: David S. Miller <davem@davemloft.net>
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Nitin Gupta <ngupta@vflare.org>
Reviewed-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ming Lei [Mon, 17 Aug 2020 10:00:55 +0000 (18:00 +0800)]
block: allow for_each_bvec to support zero len bvec
commit
7e24969022cbd61ddc586f14824fc205661bb124 upstream.
Block layer usually doesn't support or allow zero-length bvec. Since
commit
1bdc76aea115 ("iov_iter: use bvec iterator to implement
iterate_bvec()"), iterate_bvec() switches to bvec iterator. However,
Al mentioned that 'Zero-length segments are not disallowed' in iov_iter.
Fixes for_each_bvec() so that it can move on after seeing one zero
length bvec.
Fixes:
1bdc76aea115 ("iov_iter: use bvec iterator to implement iterate_bvec()")
Reported-by: syzbot <syzbot+61acc40a49a3e46e25ea@syzkaller.appspotmail.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Tested-by: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: <stable@vger.kernel.org>
Link: https://www.mail-archive.com/linux-kernel@vger.kernel.org/msg2262077.html
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Takashi Sakamoto [Sun, 23 Aug 2020 07:55:45 +0000 (16:55 +0900)]
ALSA: firewire-digi00x: exclude Avid Adrenaline from detection
commit
acd46a6b6de88569654567810acad2b0a0a25cea upstream.
Avid Adrenaline is reported that ALSA firewire-digi00x driver is bound to.
However, as long as he investigated, the design of this model is hardly
similar to the one of Digi 00x family. It's better to exclude the model
from modalias of ALSA firewire-digi00x driver.
This commit changes device entries so that the model is excluded.
$ python3 crpp < ~/git/am-config-rom/misc/avid-adrenaline.img
ROM header and bus information block
-----------------------------------------------------------------
400
04203a9c bus_info_length 4, crc_length 32, crc 15004
404
31333934 bus_name "1394"
408
e064a002 irmc 1, cmc 1, isc 1, bmc 0, cyc_clk_acc 100, max_rec 10 (2048)
40c
00a07e01 company_id 00a07e |
410
00085257 device_id
0100085257 | EUI-64
00a07e0100085257
root directory
-----------------------------------------------------------------
414
0005d08c directory_length 5, crc 53388
418
0300a07e vendor
41c
8100000c --> descriptor leaf at 44c
420
0c008380 node capabilities
424
8d000002 --> eui-64 leaf at 42c
428
d1000004 --> unit directory at 438
eui-64 leaf at 42c
-----------------------------------------------------------------
42c
0002410f leaf_length 2, crc 16655
430
00a07e01 company_id 00a07e |
434
00085257 device_id
0100085257 | EUI-64
00a07e0100085257
unit directory at 438
-----------------------------------------------------------------
438
0004d6c9 directory_length 4, crc 54985
43c
1200a02d specifier id: 1394 TA
440
13014001 version: Vender Unique and AV/C
444
17000001 model
448
81000009 --> descriptor leaf at 46c
descriptor leaf at 44c
-----------------------------------------------------------------
44c
00077205 leaf_length 7, crc 29189
450
00000000 textual descriptor
454
00000000 minimal ASCII
458
41766964 "Avid"
45c
20546563 " Tec"
460
686e6f6c "hnol"
464
6f677900 "ogy"
468
00000000
descriptor leaf at 46c
-----------------------------------------------------------------
46c
000599a5 leaf_length 5, crc 39333
470
00000000 textual descriptor
474
00000000 minimal ASCII
478
41647265 "Adre"
47c
6e616c69 "nali"
480
6e650000 "ne"
Reported-by: Simon Wood <simon@mungewell.org>
Fixes:
9edf723fd858 ("ALSA: firewire-digi00x: add skeleton for Digi 002/003 family")
Cc: <stable@vger.kernel.org> # 4.4+
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20200823075545.56305-1-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Takashi Iwai [Tue, 1 Sep 2020 13:18:02 +0000 (15:18 +0200)]
ALSA: pcm: oss: Remove superfluous WARN_ON() for mulaw sanity check
commit
949a1ebe8cea7b342085cb6a4946b498306b9493 upstream.
The PCM OSS mulaw plugin has a check of the format of the counter part
whether it's a linear format. The check is with snd_BUG_ON() that
emits WARN_ON() when the debug config is set, and it confuses
syzkaller as if it were a serious issue. Let's drop snd_BUG_ON() for
avoiding that.
While we're at it, correct the error code to a more suitable, EINVAL.
Reported-by: syzbot+23b22dc2e0b81cbfcc95@syzkaller.appspotmail.com
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200901131802.18157-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tong Zhang [Mon, 24 Aug 2020 22:45:41 +0000 (18:45 -0400)]
ALSA: ca0106: fix error code handling
commit
ee0761d1d8222bcc5c86bf10849dc86cf008557c upstream.
snd_ca0106_spi_write() returns 1 on error, snd_ca0106_pcm_power_dac()
is returning the error code directly, and the caller is expecting an
negative error code
Signed-off-by: Tong Zhang <ztong0001@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200824224541.1260307-1-ztong0001@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rogan Dawes [Wed, 17 Jul 2019 09:14:33 +0000 (11:14 +0200)]
usb: qmi_wwan: add D-Link DWM-222 A2 device ID
[ Upstream commit
7d6053097311643545a8118100175a39bd6fa637 ]
Signed-off-by: Rogan Dawes <rogan@dawes.za.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Bjørn Mork [Tue, 13 Jun 2017 17:10:18 +0000 (19:10 +0200)]
qmi_wwan: new Telewell and Sierra device IDs
[ Upstream commit
60cfe1eaccb8af598ebe1bdc44e157ea30fcdd81 ]
A new Sierra Wireless EM7305 device ID used in a Toshiba laptop,
and two Longcheer device IDs entries used by Telewell TW-3G HSPA+
branded modems.
Reported-by: Petr Kloc <petr_kloc@yahoo.com>
Reported-by: Teemu Likonen <tlikonen@iki.fi>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Daniele Palmas [Mon, 10 Apr 2017 15:34:23 +0000 (17:34 +0200)]
drivers: net: usb: qmi_wwan: add QMI_QUIRK_SET_DTR for Telit PID 0x1201
[ Upstream commit
14cf4a771b3098e431d2677e3533bdd962e478d8 ]
Telit LE920A4 uses the same pid 0x1201 of LE920, but modem
implementation is different, since it requires DTR to be set for
answering to qmi messages.
This patch replaces QMI_FIXED_INTF with QMI_QUIRK_SET_DTR: tests on
LE920 have been performed in order to verify backward compatibility.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Daniele Palmas [Wed, 9 Oct 2019 09:07:18 +0000 (11:07 +0200)]
net: usb: qmi_wwan: add Telit 0x1050 composition
[ Upstream commit
e0ae2c578d3909e60e9448207f5d83f785f1129f ]
This patch adds support for Telit FN980 0x1050 composition
0x1050: tty, adb, rmnet, tty, tty, tty, tty
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Josef Bacik [Mon, 10 Aug 2020 15:42:27 +0000 (11:42 -0400)]
btrfs: fix potential deadlock in the search ioctl
[ Upstream commit
a48b73eca4ceb9b8a4b97f290a065335dbcd8a04 ]
With the conversion of the tree locks to rwsem I got the following
lockdep splat:
======================================================
WARNING: possible circular locking dependency detected
5.8.0-rc7-00165-g04ec4da5f45f-dirty #922 Not tainted
------------------------------------------------------
compsize/11122 is trying to acquire lock:
ffff889fabca8768 (&mm->mmap_lock#2){++++}-{3:3}, at: __might_fault+0x3e/0x90
but task is already holding lock:
ffff889fe720fe40 (btrfs-fs-00){++++}-{3:3}, at: __btrfs_tree_read_lock+0x39/0x180
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #2 (btrfs-fs-00){++++}-{3:3}:
down_write_nested+0x3b/0x70
__btrfs_tree_lock+0x24/0x120
btrfs_search_slot+0x756/0x990
btrfs_lookup_inode+0x3a/0xb4
__btrfs_update_delayed_inode+0x93/0x270
btrfs_async_run_delayed_root+0x168/0x230
btrfs_work_helper+0xd4/0x570
process_one_work+0x2ad/0x5f0
worker_thread+0x3a/0x3d0
kthread+0x133/0x150
ret_from_fork+0x1f/0x30
-> #1 (&delayed_node->mutex){+.+.}-{3:3}:
__mutex_lock+0x9f/0x930
btrfs_delayed_update_inode+0x50/0x440
btrfs_update_inode+0x8a/0xf0
btrfs_dirty_inode+0x5b/0xd0
touch_atime+0xa1/0xd0
btrfs_file_mmap+0x3f/0x60
mmap_region+0x3a4/0x640
do_mmap+0x376/0x580
vm_mmap_pgoff+0xd5/0x120
ksys_mmap_pgoff+0x193/0x230
do_syscall_64+0x50/0x90
entry_SYSCALL_64_after_hwframe+0x44/0xa9
-> #0 (&mm->mmap_lock#2){++++}-{3:3}:
__lock_acquire+0x1272/0x2310
lock_acquire+0x9e/0x360
__might_fault+0x68/0x90
_copy_to_user+0x1e/0x80
copy_to_sk.isra.32+0x121/0x300
search_ioctl+0x106/0x200
btrfs_ioctl_tree_search_v2+0x7b/0xf0
btrfs_ioctl+0x106f/0x30a0
ksys_ioctl+0x83/0xc0
__x64_sys_ioctl+0x16/0x20
do_syscall_64+0x50/0x90
entry_SYSCALL_64_after_hwframe+0x44/0xa9
other info that might help us debug this:
Chain exists of:
&mm->mmap_lock#2 --> &delayed_node->mutex --> btrfs-fs-00
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(btrfs-fs-00);
lock(&delayed_node->mutex);
lock(btrfs-fs-00);
lock(&mm->mmap_lock#2);
*** DEADLOCK ***
1 lock held by compsize/11122:
#0:
ffff889fe720fe40 (btrfs-fs-00){++++}-{3:3}, at: __btrfs_tree_read_lock+0x39/0x180
stack backtrace:
CPU: 17 PID: 11122 Comm: compsize Kdump: loaded Not tainted 5.8.0-rc7-00165-g04ec4da5f45f-dirty #922
Hardware name: Quanta Tioga Pass Single Side 01-
0030993006/Tioga Pass Single Side, BIOS F08_3A18 12/20/2018
Call Trace:
dump_stack+0x78/0xa0
check_noncircular+0x165/0x180
__lock_acquire+0x1272/0x2310
lock_acquire+0x9e/0x360
? __might_fault+0x3e/0x90
? find_held_lock+0x72/0x90
__might_fault+0x68/0x90
? __might_fault+0x3e/0x90
_copy_to_user+0x1e/0x80
copy_to_sk.isra.32+0x121/0x300
? btrfs_search_forward+0x2a6/0x360
search_ioctl+0x106/0x200
btrfs_ioctl_tree_search_v2+0x7b/0xf0
btrfs_ioctl+0x106f/0x30a0
? __do_sys_newfstat+0x5a/0x70
? ksys_ioctl+0x83/0xc0
ksys_ioctl+0x83/0xc0
__x64_sys_ioctl+0x16/0x20
do_syscall_64+0x50/0x90
entry_SYSCALL_64_after_hwframe+0x44/0xa9
The problem is we're doing a copy_to_user() while holding tree locks,
which can deadlock if we have to do a page fault for the copy_to_user().
This exists even without my locking changes, so it needs to be fixed.
Rework the search ioctl to do the pre-fault and then
copy_to_user_nofault for the copying.
CC: stable@vger.kernel.org # 4.4+
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Daniel Borkmann [Fri, 1 Nov 2019 23:17:56 +0000 (00:17 +0100)]
uaccess: Add non-pagefault user-space write function
[ Upstream commit
1d1585ca0f48fe7ed95c3571f3e4a82b2b5045dc ]
Commit
3d7081822f7f ("uaccess: Add non-pagefault user-space read functions")
missed to add probe write function, therefore factor out a probe_write_common()
helper with most logic of probe_kernel_write() except setting KERNEL_DS, and
add a new probe_user_write() helper so it can be used from BPF side.
Again, on some archs, the user address space and kernel address space can
co-exist and be overlapping, so in such case, setting KERNEL_DS would mean
that the given address is treated as being in kernel address space.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Link: https://lore.kernel.org/bpf/9df2542e68141bfa3addde631441ee45503856a8.1572649915.git.daniel@iogearbox.net
Signed-off-by: Sasha Levin <sashal@kernel.org>
Masami Hiramatsu [Wed, 15 May 2019 05:38:18 +0000 (14:38 +0900)]
uaccess: Add non-pagefault user-space read functions
[ Upstream commit
3d7081822f7f9eab867d9bcc8fd635208ec438e0 ]
Add probe_user_read(), strncpy_from_unsafe_user() and
strnlen_unsafe_user() which allows caller to access user-space
in IRQ context.
Current probe_kernel_read() and strncpy_from_unsafe() are
not available for user-space memory, because it sets
KERNEL_DS while accessing data. On some arch, user address
space and kernel address space can be co-exist, but others
can not. In that case, setting KERNEL_DS means given
address is treated as a kernel address space.
Also strnlen_user() is only available from user context since
it can sleep if pagefault is enabled.
To access user-space memory without pagefault, we need
these new functions which sets USER_DS while accessing
the data.
Link: http://lkml.kernel.org/r/155789869802.26965.4940338412595759063.stgit@devnote2
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Josef Bacik [Mon, 10 Aug 2020 15:42:31 +0000 (11:42 -0400)]
btrfs: set the lockdep class for log tree extent buffers
[ Upstream commit
d3beaa253fd6fa40b8b18a216398e6e5376a9d21 ]
These are special extent buffers that get rewound in order to lookup
the state of the tree at a specific point in time. As such they do not
go through the normal initialization paths that set their lockdep class,
so handle them appropriately when they are created and before they are
locked.
CC: stable@vger.kernel.org # 4.4+
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Nikolay Borisov [Wed, 15 Aug 2018 15:26:54 +0000 (18:26 +0300)]
btrfs: Remove extraneous extent_buffer_get from tree_mod_log_rewind
[ Upstream commit
24cee18a1c1d7c731ea5987e0c99daea22ae7f4a ]
When a rewound buffer is created it already has a ref count of 1 and the
dummy flag set. Then another ref is taken bumping the count to 2.
Finally when this buffer is released from btrfs_release_path the extra
reference is decremented by the special handling code in
free_extent_buffer.
However, this special code is in fact redundant sinca ref count of 1 is
still correct since the buffer is only accessed via btrfs_path struct.
This paves the way forward of removing the special handling in
free_extent_buffer.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Nikolay Borisov [Wed, 15 Aug 2018 15:26:53 +0000 (18:26 +0300)]
btrfs: Remove redundant extent_buffer_get in get_old_root
[ Upstream commit
6c122e2a0c515cfb3f3a9cefb5dad4cb62109c78 ]
get_old_root used used only by btrfs_search_old_slot to initialise the
path structure. The old root is always a cloned buffer (either via alloc
dummy or via btrfs_clone_extent_buffer) and its reference count is 2: 1
from allocation, 1 from extent_buffer_get call in get_old_root.
This latter explicit ref count acquire operation is in fact unnecessary
since the semantic is such that the newly allocated buffer is handed
over to the btrfs_path for lifetime management. Considering this just
remove the extra extent_buffer_get in get_old_root.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Josef Bacik [Mon, 10 Aug 2020 15:42:26 +0000 (11:42 -0400)]
btrfs: drop path before adding new uuid tree entry
commit
9771a5cf937129307d9f58922d60484d58ababe7 upstream.
With the conversion of the tree locks to rwsem I got the following
lockdep splat:
======================================================
WARNING: possible circular locking dependency detected
5.8.0-rc7-00167-g0d7ba0c5b375-dirty #925 Not tainted
------------------------------------------------------
btrfs-uuid/7955 is trying to acquire lock:
ffff88bfbafec0f8 (btrfs-root-00){++++}-{3:3}, at: __btrfs_tree_read_lock+0x39/0x180
but task is already holding lock:
ffff88bfbafef2a8 (btrfs-uuid-00){++++}-{3:3}, at: __btrfs_tree_read_lock+0x39/0x180
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (btrfs-uuid-00){++++}-{3:3}:
down_read_nested+0x3e/0x140
__btrfs_tree_read_lock+0x39/0x180
__btrfs_read_lock_root_node+0x3a/0x50
btrfs_search_slot+0x4bd/0x990
btrfs_uuid_tree_add+0x89/0x2d0
btrfs_uuid_scan_kthread+0x330/0x390
kthread+0x133/0x150
ret_from_fork+0x1f/0x30
-> #0 (btrfs-root-00){++++}-{3:3}:
__lock_acquire+0x1272/0x2310
lock_acquire+0x9e/0x360
down_read_nested+0x3e/0x140
__btrfs_tree_read_lock+0x39/0x180
__btrfs_read_lock_root_node+0x3a/0x50
btrfs_search_slot+0x4bd/0x990
btrfs_find_root+0x45/0x1b0
btrfs_read_tree_root+0x61/0x100
btrfs_get_root_ref.part.50+0x143/0x630
btrfs_uuid_tree_iterate+0x207/0x314
btrfs_uuid_rescan_kthread+0x12/0x50
kthread+0x133/0x150
ret_from_fork+0x1f/0x30
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(btrfs-uuid-00);
lock(btrfs-root-00);
lock(btrfs-uuid-00);
lock(btrfs-root-00);
*** DEADLOCK ***
1 lock held by btrfs-uuid/7955:
#0:
ffff88bfbafef2a8 (btrfs-uuid-00){++++}-{3:3}, at: __btrfs_tree_read_lock+0x39/0x180
stack backtrace:
CPU: 73 PID: 7955 Comm: btrfs-uuid Kdump: loaded Not tainted 5.8.0-rc7-00167-g0d7ba0c5b375-dirty #925
Hardware name: Quanta Tioga Pass Single Side 01-
0030993006/Tioga Pass Single Side, BIOS F08_3A18 12/20/2018
Call Trace:
dump_stack+0x78/0xa0
check_noncircular+0x165/0x180
__lock_acquire+0x1272/0x2310
lock_acquire+0x9e/0x360
? __btrfs_tree_read_lock+0x39/0x180
? btrfs_root_node+0x1c/0x1d0
down_read_nested+0x3e/0x140
? __btrfs_tree_read_lock+0x39/0x180
__btrfs_tree_read_lock+0x39/0x180
__btrfs_read_lock_root_node+0x3a/0x50
btrfs_search_slot+0x4bd/0x990
btrfs_find_root+0x45/0x1b0
btrfs_read_tree_root+0x61/0x100
btrfs_get_root_ref.part.50+0x143/0x630
btrfs_uuid_tree_iterate+0x207/0x314
? btree_readpage+0x20/0x20
btrfs_uuid_rescan_kthread+0x12/0x50
kthread+0x133/0x150
? kthread_create_on_node+0x60/0x60
ret_from_fork+0x1f/0x30
This problem exists because we have two different rescan threads,
btrfs_uuid_scan_kthread which creates the uuid tree, and
btrfs_uuid_tree_iterate that goes through and updates or deletes any out
of date roots. The problem is they both do things in different order.
btrfs_uuid_scan_kthread() reads the tree_root, and then inserts entries
into the uuid_root. btrfs_uuid_tree_iterate() scans the uuid_root, but
then does a btrfs_get_fs_root() which can read from the tree_root.
It's actually easy enough to not be holding the path in
btrfs_uuid_scan_kthread() when we add a uuid entry, as we already drop
it further down and re-start the search when we loop. So simply move
the path release before we add our entry to the uuid tree.
This also fixes a problem where we're holding a path open after we do
btrfs_end_transaction(), which has it's own problems.
CC: stable@vger.kernel.org # 4.4+
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jason Gunthorpe [Fri, 4 Sep 2020 23:36:19 +0000 (16:36 -0700)]
include/linux/log2.h: add missing () around n in roundup_pow_of_two()
[ Upstream commit
428fc0aff4e59399ec719ffcc1f7a5d29a4ee476 ]
Otherwise gcc generates warnings if the expression is complicated.
Fixes:
312a0c170945 ("[PATCH] LOG2: Alter roundup_pow_of_two() so that it can use a ilog2() on a constant")
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Link: https://lkml.kernel.org/r/0-v1-8a2697e3c003+41165-log_brackets_jgg@nvidia.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>