Arnd Bergmann [Thu, 5 May 2022 14:44:18 +0000 (16:44 +0200)]
Merge tag 'stm32-dt-for-v5.19-1' of git://git./linux/kernel/git/atorgue/stm32 into arm/dt
STM32 DT for v5.19, round 1
Highlights:
----------
-MCU:
-Fix pinctrl node names to match with pinctrl yaml.
- MPU:
-General:
- Fix pinctrl node names to match with pinctrl yaml.
- Add Protonics boards support based on STM32MP151A SoC:
- PRTT1C - 10BaseT1L switch: mainly embeds a sja1105q switch with
TI and Micrel 10BaseT Phys and wifi support.
- PRTT1S - 10BaseT1L CO2 sensor board: mainly embeds I2C humidity
and CO2 sensors.
- PRTT1A - 10BaseT1L multi functional controller.
- ST boards:
- Add RTC support on stm32mp13.
- Add button and heartbit support on stm32mp13 DK board.
- Add a secure version of STM32MP15 ED1/EV1/DK1/DK2 boards based
on OP-TEE OS and SCMI protocol.
- DH boards:
- Use MCO2 to generate PHY clock and ETHRX clock in order to release
internal PLL for a better SD card usage.
- Add 1ms PHY post-reset on Avenger96 board to match with PHY
requirements.
* tag 'stm32-dt-for-v5.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32: (24 commits)
ARM: dts: stm32: Add SCMI version of STM32 boards (DK1/DK2/ED1/EV1)
dt-bindings: arm: stm32: Add SCMI version of STM32 boards (DK1/DK2/ED1/EV1)
ARM: dts: stm32: enable optee firmware and SCMI support on STM32MP15
dt-bindings: reset: stm32mp15: rename RST_SCMI define
dt-bindings: clock: stm32mp15: rename CK_SCMI define
dt-bindings: clock: stm32mp1: describes clocks if "st,stm32mp1-rcc-secure"
dt-bindings: rcc: Add optional external ethernet RX clock properties
ARM: dts: stm32: add UserPA13 button on stm32mp135f-dk
ARM: dts: stm32: add blue led (Linux heartbeat) on stm32mp135f-dk
ARM: dts: stm32: add EXTI interrupt-parent to pinctrl node on stm32mp131
ARM: dts: stm32: add support for Protonic PRTT1x boards
ARM: dts: stm32: stm32mp15-pinctrl: add spi1-1 pinmux group
dt-bindings: net: silabs,wfx: add prt,prtt1c-wfm200 antenna variant
dt-bindings: arm: stm32: Add compatible strings for Protonic T1L boards
dt-bindings: arm: stm32: correct blank lines
dt-bindings: arm: stm32: narrow DH STM32MP1 SoM boards
ARM: dts: stm32: enable RTC support on stm32mp135f-dk
ARM: dts: stm32: add RTC node on stm32mp131
ARM: dts: stm32: Fix PHY post-reset delay on Avenger96
ARM: dts: stm32: fix pinctrl node name warnings (MPU soc)
...
Link: https://lore.kernel.org/r/5818c943-882d-7e50-430d-ae3299a108ee@foss.st.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Alexandre Torgue [Fri, 22 Apr 2022 15:09:52 +0000 (17:09 +0200)]
ARM: dts: stm32: Add SCMI version of STM32 boards (DK1/DK2/ED1/EV1)
Add a "secure" version based on SCMI of STM32 boards. Only boards
provided by STMicroelectronics are concerned:
-STM32MP157A-DK1
-STM32MP157C-DK2
-STM32MP157C-ED1
-STM32MP157C-EV1
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Alexandre Torgue [Fri, 22 Apr 2022 15:09:51 +0000 (17:09 +0200)]
dt-bindings: arm: stm32: Add SCMI version of STM32 boards (DK1/DK2/ED1/EV1)
Add a "secure" version based on SCMI of STM32 boards. Only boards
provided by STMicroelectronics are concerned:
-STM32MP157A-DK1
-STM32MP157C-DK2
-STM32MP157C-ED1
-STM32MP157C-EV1
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Acked-by: Rob Herring <robh@kernel.org>
Alexandre Torgue [Fri, 22 Apr 2022 15:09:50 +0000 (17:09 +0200)]
ARM: dts: stm32: enable optee firmware and SCMI support on STM32MP15
Enable optee and SCMI clocks/reset protocols support.
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Alexandre Torgue [Fri, 22 Apr 2022 15:09:48 +0000 (17:09 +0200)]
dt-bindings: reset: stm32mp15: rename RST_SCMI define
As we only have one SCMI instance, it's not necessary to add an index to
the name.
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Acked-by: Rob Herring <robh@kernel.org>
Alexandre Torgue [Fri, 22 Apr 2022 15:09:47 +0000 (17:09 +0200)]
dt-bindings: clock: stm32mp15: rename CK_SCMI define
As we only have one SCMI instance, it's not necessary to add an index to
the name.
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Acked-by: Rob Herring <robh@kernel.org>
Alexandre Torgue [Fri, 22 Apr 2022 15:09:46 +0000 (17:09 +0200)]
dt-bindings: clock: stm32mp1: describes clocks if "st,stm32mp1-rcc-secure"
In case of "st,stm32mp1-rcc-secure" (stm32mp1 clock driver with RCC
security support hardened), "clocks" and "clock-names" describe oscillators
and are required.
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Marek Vasut [Sun, 10 Apr 2022 22:05:14 +0000 (00:05 +0200)]
dt-bindings: rcc: Add optional external ethernet RX clock properties
Describe optional external ethernet RX clock in the DT binding
to fix dtbs_check warnings like:
arch/arm/boot/dts/stm32mp153c-dhcom-drc02.dt.yaml: rcc@
50000000: 'assigned-clock-parents', 'assigned-clock-rates', 'assigned-clocks', 'clock-names', 'clocks' do not match any of the regexes: 'pinctrl-[0-9]+'
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: Gabriel Fernandez <gabriel.fernandez@foss.st.com>
Cc: Rob Herring <robh+dt@kernel.org>
To: devicetree@vger.kernel.org
Acked-by: Gabriel Fernandez <gabriel.fernandez@foss.st.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220410220514.21779-1-marex@denx.de
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Fabien Dessenne [Tue, 3 May 2022 09:41:33 +0000 (11:41 +0200)]
ARM: dts: stm32: add UserPA13 button on stm32mp135f-dk
The PA13 user button is connected to the PA13 pin of the stm32mp135f-dk
board. It requires an internal pull-up configuration.
Signed-off-by: Fabien Dessenne <fabien.dessenne@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Fabien Dessenne [Tue, 3 May 2022 09:41:24 +0000 (11:41 +0200)]
ARM: dts: stm32: add blue led (Linux heartbeat) on stm32mp135f-dk
The blue led (Linux heartbeat) is connected to the PA14 pin of the
stm32mp135f-dk board.
Signed-off-by: Fabien Dessenne <fabien.dessenne@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Fabien Dessenne [Tue, 3 May 2022 09:06:21 +0000 (11:06 +0200)]
ARM: dts: stm32: add EXTI interrupt-parent to pinctrl node on stm32mp131
Add interrupt-parent property in pinctrl node to use GPIO as IRQ.
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Signed-off-by: Fabien Dessenne <fabien.dessenne@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Arnd Bergmann [Tue, 3 May 2022 13:29:13 +0000 (15:29 +0200)]
Merge tag 'amlogic-arm-dt-for-v5.19' of git://git./linux/kernel/git/amlogic/linux into arm/dt
Amlogic ARM DT changes for v5.19:
- align SPI NOR node name with dtschema
* tag 'amlogic-arm-dt-for-v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/amlogic/linux:
ARM: dts: meson: align SPI NOR node name with dtschema
Link: https://lore.kernel.org/r/fbd7cbe7-1fe9-7009-37d6-c01b15c93032@baylibre.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Tue, 3 May 2022 13:27:58 +0000 (15:27 +0200)]
Merge tag 'amlogic-arm64-dt-for-v5.19' of git://git./linux/kernel/git/amlogic/linux into arm/dt
Amlogic ARM64 DT changes for v5.19:
- DTS makefile alpsa sort
- align SPI NOR node name with dtschema
- add support for S4 power domain, gpio_intc, pinctrl
- updates and fixes for JetHub D1/H1 boards
* tag 'amlogic-arm64-dt-for-v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/amlogic/linux:
arm64: dts: meson: alpa sort the board Makefile
arm64: dts: meson: align SPI NOR node name with dtschema
arm64: dts: add support for S4 power domain controller
arm64: dts: meson-s4: add gpio_intc node
arm64: dts: meson-s4: add pinctrl node
arm64: meson: update WiFi SDIO in dts for JetHub D1
arm64: meson: update SDIO voltage in dts for JetHub D1
arm64: meson: dts: update serial alias in dts for JetHub D1
arm64: meson: add dts bluetooth node for JetHub H1
Link: https://lore.kernel.org/r/1e5179ab-2d92-0d64-c57b-e002ec2f0806@baylibre.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Tue, 3 May 2022 13:27:33 +0000 (15:27 +0200)]
Merge tag 'ux500-dts-v5.19' of git://git./linux/kernel/git/linusw/linux-nomadik into arm/dt
Ux500 DTS updates for the v5.19 kernel cycle:
- New devicetree for Codina TMO (SGH-T599).
- Add the Amastaos proximity sensor to the Codina.
- Add line impedance per machine to the Fuel Gauge
nodes.
- Add GPS to Janice, Skomer and Codina.
- Add NFC to the Codina for GT-I8160P.
- Some janitorial like clock names.
* tag 'ux500-dts-v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
ARM: dts: ux500: Add GPS to the Codina
ARM: dts: ux500: Add NFC to the Codina
ARM: dts: ux500: Add GPS to Skomer device tree
ARM: dts: ux500: Add GPS to Janice device tree
ARM: dts: ux500: Add line impedance to fuel gauge
ARM: dts: ux500: Register Amstaos proximity sensor
ARM: dts: ux500: Add Codina TMO device tree
dt-bindings: arm: ux500: Document Codina-TMO
ARM: dts: ste-dbx: Update spi clock-names property
Link: https://lore.kernel.org/r/CACRpkdYngWscqak5phKm58O2GF0RmVETgwW4NCKTBiASdaEcyg@mail.gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Tue, 3 May 2022 13:26:13 +0000 (15:26 +0200)]
Merge tag 'omap-for-v5.19/dt-signed' of git://git./linux/kernel/git/tmlind/linux-omap into arm/dt
Devicetree changes for omaps
Devicetree changes for omaps:
- A series of changes to fix devicetree binding check warnings for omaps
the the use of clock-output-names and clksel bindings
- Update Ethernet node names for omaps
- Pinctrl updates for logicpd-som-lv
- A series of updates for am335x-guardian
- Regulator range update for am335x-baltos
Note that this branch is based on a upstream IOMMU fix as it's needed for
booting on some SoCs.
* tag 'omap-for-v5.19/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (29 commits)
ARM: dts: am335x-baltos: update MPU regulator range
ARM: dts: am335x: Guardian: Update comments
ARM: dts: am335x: Guardian: Add gpio line manes
ARM: dts: am335x: Guardian: Update interface pinmux
ARM: dts: am335x: Guardian: Disable DMA property of USB1
ARM: dts: am335x: Guardian: Enable UART port two
ARM: dts: am335x: Guardian: Update backlight parameter
ARM: dts: am335x: Guardian: Add lcd port
ARM: dts: am335x: Guardian: Update regulator node name
ARM: dts: am335x: Guardian: Update beeper label
ARM: dts: am335x: Guardian: Update life led
ARM: dts: am335x: Guardian: Remove mmc status led
ARM: dts: am335x: Guardian: Disable poweroff support from RTC
ARM: dts: am335x: Guardian: Add keypad
ARM: dts: am335x: Guardian: Rename power button label
ARM: dts: am335x: Guardian: Update NAND partition table
ARM: dts: logicpd-som-lv: Move pinmuxing to peripheral nodes
ARM: dts: omap3/4/5: fix ethernet node name for different OMAP boards
ARM: dts: Drop custom clkctrl compatible and update omap5 l4per
ARM: dts: Add clock-output-names for omap5
...
Link: https://lore.kernel.org/r/pull-1650961799-428630@atomide.com-2
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Tue, 3 May 2022 13:25:36 +0000 (15:25 +0200)]
Merge tag 'bindings-signed' of git://git./linux/kernel/git/tmlind/linux-omap into arm/dt
Clock binding updates for omaps
Minor clock binding changes to document clock-output-names usage for omaps
so we can fix lots of related dt bindings check warnings. The related driver
changes already got merged for v5.18.
* tag 'bindings-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
dt-bindings: clock: ti: Add clock-output-names for TI composite clocks
dt-bindings: clock: ti: Add clock-output-names for clockctrl
dt-bindings: omap: Add clock-output-names and #clock-cells
Link: https://lore.kernel.org/r/pull-1650961799-428630@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Tue, 3 May 2022 13:25:04 +0000 (15:25 +0200)]
Merge tag 'renesas-dt-bindings-for-v5.19-tag1' of git://git./linux/kernel/git/geert/renesas-devel into arm/dt
Renesas DT binding updates for v5.19
- Document support for the new RZ/G2UL SoC and the RZ/G2UL SMARC EVK
development board.
* tag 'renesas-dt-bindings-for-v5.19-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
dt-bindings: arm: renesas: Document Renesas RZ/G2UL SMARC EVK
dt-bindings: power: renesas,rzg2l-sysc: Document RZ/G2UL SoC
Link: https://lore.kernel.org/r/cover.1650638516.git.geert+renesas@glider.be
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Tue, 3 May 2022 13:24:08 +0000 (15:24 +0200)]
Merge tag 'renesas-arm-dt-for-v5.19-tag1' of git://git./linux/kernel/git/geert/renesas-devel into arm/dt
Renesas ARM DT updates for v5.19
- ADC, SDHI, CAN-FD, I2C, QSPI, timer, watchdog, sound, USB, SPI, GPU,
cpufreq, and thermal support for the RZ/V2L SoC, and the RZ/V2L
SMARC EVK development board,
- USB, I2C, Audio, NOR Flash, timer, SPI support for RZ/G2LC SMARC EVK
development board,
- Can-FD support for the R-Car M30W+ and V3U SoCs, and the Falcon
development board,
- I2C and GPIO support for the R-Car S4-8 SoC,
- I2C EEPROM support for the Falcon development board,
- SPI Multi I/O Bus Controller (RPC-IF) support for the R-Car H3,
M3-W(+), M3-N, E3, and D3 SoCs,
- RPC HyperFlash support for the Draak, Ebisu, Salvator-X(S), and ULCB
development boards,
- Initial support (UART, DMAC, pin control, SDHI, eMMC, Ethernet) for
the RZ/G2UL SoC, and the RZ/G2UL SMARC EVK development board,
- Miscellaneous fixes and improvements.
* tag 'renesas-arm-dt-for-v5.19-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel: (55 commits)
ARM: dts: r9a06g032: Drop "arm,cortex-a7-timer" from timer node
arm64: dts: renesas: r8a779f0: Add GPIO nodes
arm64: dts: renesas: rzg2ul-smarc-som: Enable Ethernet on SMARC platform
arm64: dts: renesas: rzg2ul-smarc-som: Enable eMMC on SMARC platform
arm64: dts: renesas: rzg2ul-smarc: Enable microSD on SMARC platform
arm64: dts: renesas: r9a07g043: Add GbEthernet nodes
arm64: dts: renesas: r9a07g043: Add SDHI nodes
arm64: dts: renesas: rzg2ul-smarc: Add scif0 and audio clk pins
arm64: dts: renesas: r9a07g043: Fillup the pinctrl stub node
arm64: dts: renesas: Add initial device tree for RZ/G2UL Type-1 SMARC EVK
arm64: dts: renesas: Add initial DTSI for RZ/G2UL SoC
arm64: dts: renesas: rzg2l-smarc: Move gpios property of vccq_sdhi1 from common dtsi
arm64: dts: renesas: rzg2lc-smarc: Enable RSPI1 on carrier board
arm64: dts: renesas: ulcb: Add RPC HyperFlash device node
arm64: dts: renesas: salvator-common: Add RPC HyperFlash device node
arm64: dts: renesas: ebisu: Add RPC HyperFlash device node
arm64: dts: renesas: draak: Add RPC HyperFlash device node
arm64: dts: renesas: rcar-gen3: Add RPC device nodes
arm64: dts: renesas: rcar-gen4: Add interrupt properties to watchdog nodes
arm64: dts: renesas: rzg2: Add interrupt properties to watchdog nodes
...
Link: https://lore.kernel.org/r/cover.1650638505.git.geert+renesas@glider.be
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Oleksij Rempel [Tue, 26 Apr 2022 07:35:11 +0000 (09:35 +0200)]
ARM: dts: stm32: add support for Protonic PRTT1x boards
This boards are based on STM32MP151AAD3 and use 10BaseT1L for communication.
- PRTT1C - 10BaseT1L switch
- PRTT1S - 10BaseT1L CO2 sensor board
- PRTT1A - 10BaseT1L multi functional controller
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Oleksij Rempel [Tue, 26 Apr 2022 07:35:10 +0000 (09:35 +0200)]
ARM: dts: stm32: stm32mp15-pinctrl: add spi1-1 pinmux group
Add spi1-1 pingroup as preparation for Protonic PRTT1C board.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Oleksij Rempel [Tue, 26 Apr 2022 07:35:09 +0000 (09:35 +0200)]
dt-bindings: net: silabs,wfx: add prt,prtt1c-wfm200 antenna variant
Add compatible for wfm200 antenna configuration variant for Protonic PRTT1C
board.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Oleksij Rempel [Tue, 26 Apr 2022 07:35:08 +0000 (09:35 +0200)]
dt-bindings: arm: stm32: Add compatible strings for Protonic T1L boards
This boards are based on STM32MP151AAD3 and use 10BaseT1L for
communication.
- PRTT1C - 10BaseT1L switch
- PRTT1S - 10BaseT1L CO2 sensor board
- PRTT1A - 10BaseT1L multi functional controller
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Krzysztof Kozlowski [Mon, 25 Apr 2022 14:04:36 +0000 (16:04 +0200)]
dt-bindings: arm: stm32: correct blank lines
Correct blank lines to precesily separate entries.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Krzysztof Kozlowski [Mon, 25 Apr 2022 14:04:35 +0000 (16:04 +0200)]
dt-bindings: arm: stm32: narrow DH STM32MP1 SoM boards
The bindings for DH STM32MP1 SoM boards allows invalid combinations,
e.g. st,stm32mp153 SoC on a dh,stm32mp157c-dhcom-som SoM.
Split the enums to properly match valid setups.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Linus Walleij [Thu, 14 Apr 2022 21:40:16 +0000 (23:40 +0200)]
ARM: dts: ux500: Add GPS to the Codina
The Codina has a Broadcom BCM4751 GPS chip.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Arnd Bergmann [Thu, 21 Apr 2022 15:14:52 +0000 (17:14 +0200)]
Merge tag 'samsung-dt64-5.19' of git://git./linux/kernel/git/krzk/linux into arm/dt
Samsung DTS ARM64 changes for v5.19
1. Cleanup: move aliases of board-related features to board in
Exynos850.
2. Add specific compatibles to Multi Core Timer to allow stricter DT
schema matching.
* tag 'samsung-dt64-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
arm64: dts: tesla: add a specific compatible to MCT on FSD
arm64: dts: exynos: add a specific compatible to MCT
arm64: dts: exynos: move aliases to board in Exynos850
Link: https://lore.kernel.org/r/20220420072152.11696-3-krzysztof.kozlowski@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Thu, 21 Apr 2022 15:10:01 +0000 (17:10 +0200)]
Merge tag 'samsung-dt-5.19' of git://git./linux/kernel/git/krzk/linux into arm/dt
Samsung DTS ARM changes for v5.19
1. Several DT schema related changes to make DTBs passing schema checks:
EHCI/OHCI/DMA/Ethernet node names, DMA channels order, USB-like
compatibles.
2. Add specific compatibles to Multi Core Timer to allow stricter DT
schema matching.
3. Cleanup from deprecated bindings:
- Remove deprecated unit-address workaround for Exynos5422 Odroid XU3
LPDDR3 memory timings.
- Do not use unit-address (and SFR region) in Exynos5250 MIPI phy in
favor of syscon node (unit-address deprecated in 2016).
- Use standard generic PHYs for EHCI/OHCI device in S5PV210.
4. Fix inverted SPI CS (thus blank panel) on S5PV210 Aries boards.
5. Correct Bluetooth interupt name on S5PV210 Aries boards.
* tag 'samsung-dt-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: s5pv210: align DMA channels with dtschema
ARM: dts: s5pv210: Adjust DMA node names to match spec
ARM: dts: s5pv210: Adjust memory reg entries to match spec
ARM: dts: s5pv210: Correct interrupt name for bluetooth in Aries
ARM: dts: s5pv210: Remove spi-cs-high on panel in Aries
ARM: dts: s5pv210: Use standard arrays of generic PHYs for EHCI/OHCI device
ARM: dts: s5pv210: align EHCI/OHCI nodes with dtschema
ARM: dts: exynos: align EHCI/OHCI nodes with dtschema on Exynos4
ARM: dts: exynos: drop deprecated SFR region from MIPI phy
ARM: dts: exynos: add a specific compatible to MCT
ARM: dts: exynos: remove deprecated unit address for LPDDR3 timings on Odroid
ARM: dts: exynos: fix compatible strings for Ethernet USB devices
ARM: dts: exynos: fix ethernet node name for different odroid boards
Link: https://lore.kernel.org/r/20220420072152.11696-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Thu, 21 Apr 2022 15:08:54 +0000 (17:08 +0200)]
Merge tag 'dt-cleanup-5.19' of git://git./linux/kernel/git/krzk/linux into arm/dt
Minor cleanup of ARM DTS for v5.19
Align node names and unit addresses to DT schema and DT coding style in
nspire, ox820 and socfpga.
* tag 'dt-cleanup-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: socfpga: align interrupt controller node name with dtschema
ARM: dts: ox820: align interrupt controller node name with dtschema
ARM: dts: nspire: use lower case hex addresses in node unit addresses
Link: https://lore.kernel.org/r/20220420072152.11696-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Yegor Yefremov [Tue, 19 Apr 2022 14:39:23 +0000 (16:39 +0200)]
ARM: dts: am335x-baltos: update MPU regulator range
Update the max MPU voltage range to align with the maximum
possible value allowed in the operating-points table, which is max
target voltage of 132500 uV + 2%.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Message-Id: <
20220419143923.25196-1-yegorslists@googlemail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Gireesh Hiremath [Fri, 25 Mar 2022 10:06:13 +0000 (10:06 +0000)]
ARM: dts: am335x: Guardian: Update comments
* Add comment to improve readability
Signed-off-by: Gireesh Hiremath <Gireesh.Hiremath@in.bosch.com>
Message-Id: <
20220325100613.1494-16-Gireesh.Hiremath@in.bosch.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Gireesh Hiremath [Fri, 25 Mar 2022 10:06:12 +0000 (10:06 +0000)]
ARM: dts: am335x: Guardian: Add gpio line manes
* assign name to gpio line
Signed-off-by: Gireesh Hiremath <Gireesh.Hiremath@in.bosch.com>
Message-Id: <
20220325100613.1494-15-Gireesh.Hiremath@in.bosch.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Gireesh Hiremath [Fri, 25 Mar 2022 10:06:11 +0000 (10:06 +0000)]
ARM: dts: am335x: Guardian: Update interface pinmux
* Update interface pinmux for
- poweroff button
- battery and coincell enable
- ASP and Miraculix
Signed-off-by: Gireesh Hiremath <Gireesh.Hiremath@in.bosch.com>
Message-Id: <
20220325100613.1494-14-Gireesh.Hiremath@in.bosch.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Gireesh Hiremath [Fri, 25 Mar 2022 10:06:10 +0000 (10:06 +0000)]
ARM: dts: am335x: Guardian: Disable DMA property of USB1
* Dispble DMA property of USB1
Signed-off-by: Gireesh Hiremath <Gireesh.Hiremath@in.bosch.com>
Message-Id: <
20220325100613.1494-13-Gireesh.Hiremath@in.bosch.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Gireesh Hiremath [Fri, 25 Mar 2022 10:06:09 +0000 (10:06 +0000)]
ARM: dts: am335x: Guardian: Enable UART port two
* Add support for uart2 port
Signed-off-by: Gireesh Hiremath <Gireesh.Hiremath@in.bosch.com>
Message-Id: <
20220325100613.1494-12-Gireesh.Hiremath@in.bosch.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Gireesh Hiremath [Fri, 25 Mar 2022 10:06:08 +0000 (10:06 +0000)]
ARM: dts: am335x: Guardian: Update backlight parameter
* Update default brightness and dimming frequency
* Enable current sink, while initialization
Signed-off-by: Gireesh Hiremath <Gireesh.Hiremath@in.bosch.com>
Message-Id: <
20220325100613.1494-11-Gireesh.Hiremath@in.bosch.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Gireesh Hiremath [Fri, 25 Mar 2022 10:06:07 +0000 (10:06 +0000)]
ARM: dts: am335x: Guardian: Add lcd port
* Add port to the node lcdc
Signed-off-by: Gireesh Hiremath <Gireesh.Hiremath@in.bosch.com>
Message-Id: <
20220325100613.1494-10-Gireesh.Hiremath@in.bosch.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Gireesh Hiremath [Fri, 25 Mar 2022 10:06:06 +0000 (10:06 +0000)]
ARM: dts: am335x: Guardian: Update regulator node name
* Update mmcsd voltage regulator node name
Signed-off-by: Gireesh Hiremath <Gireesh.Hiremath@in.bosch.com>
Message-Id: <
20220325100613.1494-9-Gireesh.Hiremath@in.bosch.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Gireesh Hiremath [Fri, 25 Mar 2022 10:06:05 +0000 (10:06 +0000)]
ARM: dts: am335x: Guardian: Update beeper label
* Update lable pwm to guardian beeper
Signed-off-by: Gireesh Hiremath <Gireesh.Hiremath@in.bosch.com>
Message-Id: <
20220325100613.1494-8-Gireesh.Hiremath@in.bosch.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Gireesh Hiremath [Fri, 25 Mar 2022 10:06:04 +0000 (10:06 +0000)]
ARM: dts: am335x: Guardian: Update life led
* update life led label and pin number
Signed-off-by: Gireesh Hiremath <Gireesh.Hiremath@in.bosch.com>
Message-Id: <
20220325100613.1494-7-Gireesh.Hiremath@in.bosch.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Gireesh Hiremath [Fri, 25 Mar 2022 10:06:03 +0000 (10:06 +0000)]
ARM: dts: am335x: Guardian: Remove mmc status led
* MMC presence indicater LED removed from Guardian Board
Signed-off-by: Gireesh Hiremath <Gireesh.Hiremath@in.bosch.com>
Message-Id: <
20220325100613.1494-6-Gireesh.Hiremath@in.bosch.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Gireesh Hiremath [Fri, 25 Mar 2022 10:06:02 +0000 (10:06 +0000)]
ARM: dts: am335x: Guardian: Disable poweroff support from RTC
* Disabling poweroff support form RTC will allow poweroff
to handle from other machanism
Signed-off-by: Gireesh Hiremath <Gireesh.Hiremath@in.bosch.com>
Message-Id: <
20220325100613.1494-5-Gireesh.Hiremath@in.bosch.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Gireesh Hiremath [Fri, 25 Mar 2022 10:06:01 +0000 (10:06 +0000)]
ARM: dts: am335x: Guardian: Add keypad
* Add support to guardian mt gpio keypad
Signed-off-by: Gireesh Hiremath <Gireesh.Hiremath@in.bosch.com>
Message-Id: <
20220325100613.1494-4-Gireesh.Hiremath@in.bosch.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Gireesh Hiremath [Fri, 25 Mar 2022 10:06:00 +0000 (10:06 +0000)]
ARM: dts: am335x: Guardian: Rename power button label
* Rename label button to power button
Signed-off-by: Gireesh Hiremath <Gireesh.Hiremath@in.bosch.com>
Message-Id: <
20220325100613.1494-3-Gireesh.Hiremath@in.bosch.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Gireesh Hiremath [Fri, 25 Mar 2022 10:05:59 +0000 (10:05 +0000)]
ARM: dts: am335x: Guardian: Update NAND partition table
* Update partition table to save env and splash image
* GPMC config values optimized for Bosch Guardian Board
* NAND Chip used by Bosch Guardian Board is Micron MT29F4G08ABBFA
Signed-off-by: Gireesh Hiremath <Gireesh.Hiremath@in.bosch.com>
Message-Id: <
20220325100613.1494-2-Gireesh.Hiremath@in.bosch.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Adam Ford [Thu, 3 Mar 2022 17:18:18 +0000 (11:18 -0600)]
ARM: dts: logicpd-som-lv: Move pinmuxing to peripheral nodes
Move some pinmux references to their respective peripherals.
This keeps the pins in safe-mode until they are requested.
Signed-off-by: Adam Ford <aford173@gmail.com>
Message-Id: <
20220303171818.11060-2-aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Oleksij Rempel [Wed, 16 Feb 2022 07:49:25 +0000 (08:49 +0100)]
ARM: dts: omap3/4/5: fix ethernet node name for different OMAP boards
The node name of Ethernet controller should be "ethernet" instead of
"usbether" as required by Ethernet controller devicetree schema:
Documentation/devicetree/bindings/net/ethernet-controller.yaml
This patch can potentially affect boot loaders patching against full
node path instead of using device aliases.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Message-Id: <
20220216074927.3619425-8-o.rempel@pengutronix.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Valentin Caron [Thu, 7 Apr 2022 16:20:42 +0000 (18:20 +0200)]
ARM: dts: stm32: enable RTC support on stm32mp135f-dk
Enables the support of RTC on stm32mp135f-dk board.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@foss.st.com>
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Valentin Caron [Thu, 7 Apr 2022 16:20:41 +0000 (18:20 +0200)]
ARM: dts: stm32: add RTC node on stm32mp131
Add RTC node with compatible, clock, and interrupt properties
on stm32mp131.
Add clk_rtc_k fixed clock for RTC.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@foss.st.com>
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Marek Vasut [Fri, 25 Mar 2022 17:58:51 +0000 (18:58 +0100)]
ARM: dts: stm32: Fix PHY post-reset delay on Avenger96
Per KSZ9031RNX PHY datasheet FIGURE 7-5: POWER-UP/POWER-DOWN/RESET TIMING
Note 2: After the de-assertion of reset, wait a minimum of 100 μs before
starting programming on the MIIM (MDC/MDIO) interface.
Add 1ms post-reset delay to guarantee this figure.
Fixes:
010ca9fe500bf ("ARM: dts: stm32: Add missing ethernet PHY reset on AV96")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Fabien Dessenne [Fri, 11 Mar 2022 12:13:23 +0000 (13:13 +0100)]
ARM: dts: stm32: fix pinctrl node name warnings (MPU soc)
The recent addition pinctrl.yaml in commit
c09acbc499e8 ("dt-bindings:
pinctrl: use pinctrl.yaml") resulted in some node name warnings.
Fix the node names to the preferred 'pinctrl'.
Signed-off-by: Fabien Dessenne <fabien.dessenne@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Fabien Dessenne [Fri, 11 Mar 2022 12:14:48 +0000 (13:14 +0100)]
ARM: dts: stm32: fix pinctrl node name warnings (MCU soc)
The recent addition pinctrl.yaml in commit
c09acbc499e8 ("dt-bindings:
pinctrl: use pinctrl.yaml") resulted in some node name warnings.
Fix the node names to the preferred 'pinctrl'.
Signed-off-by: Fabien Dessenne <fabien.dessenne@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Geert Uytterhoeven [Mon, 11 Apr 2022 12:32:44 +0000 (14:32 +0200)]
ARM: dts: r9a06g032: Drop "arm,cortex-a7-timer" from timer node
"make dtbs_check":
arch/arm/boot/dts/r9a06g032-rzn1d400-db.dt.yaml: timer: compatible: 'oneOf' conditional failed, one must be fixed:
['arm,cortex-a7-timer', 'arm,armv7-timer'] is too long
'arm,cortex-a7-timer' is not one of ['arm,cortex-a15-timer']
'arm,cortex-a7-timer' is not one of ['arm,armv7-timer']
'arm,cortex-a7-timer' is not one of ['arm,armv8-timer']
From schema: Documentation/devicetree/bindings/timer/arm,arch_timer.yaml
The Cortex-A7 timer should just declare compatibility with
"arm,armv7-timer".
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/a8e0cf00a983b4c539cdb1cfad5cc6b10b423c5b.1649680220.git.geert+renesas@glider.be
Geert Uytterhoeven [Mon, 4 Apr 2022 15:35:32 +0000 (17:35 +0200)]
arm64: dts: renesas: r8a779f0: Add GPIO nodes
Add device nodes for the General Purpose Input/Output (GPIO) blocks on
the Renesas R-Car S4-8 (R8A779F0) SoC.
Note that GPIO blocks 4-7 are not added, as they can only be accessed
from the Control Domain.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/7fb68561026fa8bb5d9baf0596560c5c719a38cc.1649086225.git.geert+renesas@glider.be
Linus Walleij [Wed, 13 Apr 2022 18:46:33 +0000 (20:46 +0200)]
ARM: dts: ux500: Add NFC to the Codina
This adds the PN544 NFC chip mounted on some of the Codina models
numbered GT-I8160P. The "P" at the end of the product number
indicates that an NFC chip is mounted.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Biju Das [Sat, 2 Apr 2022 08:13:28 +0000 (09:13 +0100)]
arm64: dts: renesas: rzg2ul-smarc-som: Enable Ethernet on SMARC platform
Enable Ethernet{0,1} interfaces on RZ/G2UL SMARC EVK.
Ethernet0 pins are muxed with CAN0, CAN1, SSI1 and RSPI1 pins and Ethernet0
device selection is based on the SW1[3] switch position.
Set SW1[3] to position OFF for selecting CAN0, CAN1, SSI1 and RSPI1.
Set SW1[3] to position ON for selecting Ethernet0.
This patch disables Ethernet0 on RZ/G2UL SMARC platform by default.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20220402081328.26292-8-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Biju Das [Sat, 2 Apr 2022 08:13:27 +0000 (09:13 +0100)]
arm64: dts: renesas: rzg2ul-smarc-som: Enable eMMC on SMARC platform
RZ/G2UL SoM has both 64GB eMMC and microSD connected to SDHI0.
Both these interfaces are mutually exclusive and the SD0 device
selection is based on SW1[2] on SoM module.
Set SW1[2] to position OFF for selecting eMMC
Set SW1[2] to position ON for selecting microSD
This patch enables eMMC on RZ/G2UL SMARC platform by default.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20220402081328.26292-7-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Biju Das [Sat, 2 Apr 2022 08:13:26 +0000 (09:13 +0100)]
arm64: dts: renesas: rzg2ul-smarc: Enable microSD on SMARC platform
Enable the microSD card slot connected to SDHI1 on the RZ/G2UL SMARC
platform by removing the sdhi1 override which disabled it, and by adding
the necessary pinmux required for SDHI1.
This patch also adds gpios property to vccq_sdhi1 regulator.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20220402081328.26292-6-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Biju Das [Sat, 2 Apr 2022 08:13:25 +0000 (09:13 +0100)]
arm64: dts: renesas: r9a07g043: Add GbEthernet nodes
Add Gigabit Ethernet{0,1} nodes to SoC DTSI.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20220402081328.26292-5-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Biju Das [Sat, 2 Apr 2022 08:13:24 +0000 (09:13 +0100)]
arm64: dts: renesas: r9a07g043: Add SDHI nodes
Add SDHI{0, 1} nodes to RZ/G2UL SoC DTSI.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20220402081328.26292-4-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Biju Das [Sat, 2 Apr 2022 08:13:23 +0000 (09:13 +0100)]
arm64: dts: renesas: rzg2ul-smarc: Add scif0 and audio clk pins
Add scif0 and audio clk pins to soc pinctrl dtsi and drop deleting
the pinctrl-0 and pinctrl-names properties for scif0 node so that
we now actually make use of these properties for scif0.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20220402081328.26292-3-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Biju Das [Sat, 2 Apr 2022 08:13:22 +0000 (09:13 +0100)]
arm64: dts: renesas: r9a07g043: Fillup the pinctrl stub node
Fillup the pinctrl(GPIO) stub node in RZ/G2UL SoC DTSI.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20220402081328.26292-2-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Biju Das [Tue, 12 Apr 2022 16:13:14 +0000 (17:13 +0100)]
arm64: dts: renesas: Add initial device tree for RZ/G2UL Type-1 SMARC EVK
Add basic support for RZ/G2UL SMARC EVK (based on R9A07G043U11):
- memory
- External input clock
- CPG
- DMA
- SCIF
It shares the same carrier board with RZ/G2L, but the pin mapping is
different. Disable the device nodes which are not tested and delete the
corresponding pinctrl definitions.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20220412161314.13800-4-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Biju Das [Tue, 12 Apr 2022 16:13:13 +0000 (17:13 +0100)]
arm64: dts: renesas: Add initial DTSI for RZ/G2UL SoC
Add initial DTSI for RZ/G2UL SoC.
Both RZ/G2L and RZ/G2UL uses the same SMARC EVK. Therefore they share
the common dtsi (rz-smarc.dtsi) file. Place holders are added in
device nodes to avoid compilation errors for the devices which have
not been enabled yet on RZ/G2UL SoC.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20220412161314.13800-3-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Geert Uytterhoeven [Wed, 13 Apr 2022 11:56:04 +0000 (13:56 +0200)]
Merge tag 'renesas-r9a07g043-dt-binding-defs-tag' into HEAD
Renesas RZ/G2UL DT Binding Definitions
Clock and reset definitions for the Renesas RZ/G2UL (R9A07G043) SoC,
shared by driver and DT source files.
Biju Das [Fri, 1 Apr 2022 17:54:27 +0000 (18:54 +0100)]
arm64: dts: renesas: rzg2l-smarc: Move gpios property of vccq_sdhi1 from common dtsi
On RZ/G2{L,LC} SoM module, gpio for power selection is connected to
P39_1 whereas on RZ/G2UL it is connected to P6_1. So move gpios property
of vccq_sdhi1 regulator from common dtsi to soc specific dtsi.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20220401175427.19078-1-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Biju Das [Fri, 1 Apr 2022 14:57:02 +0000 (15:57 +0100)]
arm64: dts: renesas: rzg2lc-smarc: Enable RSPI1 on carrier board
RSPI1 (SPI1) interface is available on PMOD0 connector (J1) on the
carrier board. This patch adds pinmux and spi1 nodes to the carrier
board dtsi file and drops deleting pinctl* properties from DTS file.
RSPI1 interface is tested by setting the macro SW_RSPI_CAN to 0.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20220401145702.17954-1-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Geert Uytterhoeven [Tue, 29 Mar 2022 12:20:05 +0000 (14:20 +0200)]
arm64: dts: renesas: ulcb: Add RPC HyperFlash device node
Add the RPC HyperFlash device node along with its partitions to the
common ULCB board DTS file.
Based on a patch in the BSP by Valentine Barshak.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/61a63e819d4296760ca7ae83ef5226a2c4d7bd93.1648548339.git.geert+renesas@glider.be
Geert Uytterhoeven [Tue, 29 Mar 2022 12:20:04 +0000 (14:20 +0200)]
arm64: dts: renesas: salvator-common: Add RPC HyperFlash device node
Add the RPC HyperFlash device node along with its partitions to the
common Salvator-X(S) board DTS file.
Based on a patch in the BSP by Valentine Barshak.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/cfc6af8a4c42febcc405b7356c38448eec8e29b0.1648548339.git.geert+renesas@glider.be
Geert Uytterhoeven [Tue, 29 Mar 2022 12:20:03 +0000 (14:20 +0200)]
arm64: dts: renesas: ebisu: Add RPC HyperFlash device node
Add the RPC HyperFlash device node along with its partitions to the
common Ebisu board DTS file.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/b14c769f62211b67d90dbd2f127357756e6cb4fa.1648548339.git.geert+renesas@glider.be
Geert Uytterhoeven [Tue, 29 Mar 2022 12:20:02 +0000 (14:20 +0200)]
arm64: dts: renesas: draak: Add RPC HyperFlash device node
Add the RPC HyperFlash device node along with its partitions to the
common Draak board DTS file.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/0f3d3018ecfcdce1bce67708708a6d3a98368b10.1648548339.git.geert+renesas@glider.be
Geert Uytterhoeven [Tue, 29 Mar 2022 12:20:01 +0000 (14:20 +0200)]
arm64: dts: renesas: rcar-gen3: Add RPC device nodes
Add device nodes for the SPI Multi I/O Bus Controllers (RPC-IF) on the
various R-Car Gen3 SoCs that do not have support for them yet in their
device trees (R-Car H3, M3-W, M3-W+, M3-N, E3, and D3).
Based on patches in the BSP by Valentine Barshak.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/3231749c7b63df1a2134daabe66446a3e0e5515b.1648548339.git.geert+renesas@glider.be
Wolfram Sang [Tue, 22 Mar 2022 09:55:12 +0000 (10:55 +0100)]
arm64: dts: renesas: rcar-gen4: Add interrupt properties to watchdog nodes
Driver doesn't use it yet, but let's describe the HW properly.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20220322095512.4707-6-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Wolfram Sang [Tue, 22 Mar 2022 09:55:11 +0000 (10:55 +0100)]
arm64: dts: renesas: rzg2: Add interrupt properties to watchdog nodes
Driver doesn't use it yet, but let's describe the HW properly.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20220322095512.4707-5-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Wolfram Sang [Tue, 22 Mar 2022 09:55:10 +0000 (10:55 +0100)]
arm64: dts: renesas: rcar-gen3: Add interrupt properties to watchdog nodes
Driver doesn't use it yet, but let's describe the HW properly.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20220322095512.4707-4-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Wolfram Sang [Tue, 22 Mar 2022 09:55:09 +0000 (10:55 +0100)]
ARM: dts: rzg1: Add interrupt properties to watchdog nodes
Driver doesn't use it yet, but let's describe the HW properly.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20220322095512.4707-3-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Wolfram Sang [Tue, 22 Mar 2022 09:55:08 +0000 (10:55 +0100)]
ARM: dts: rcar-gen2: Add interrupt properties to watchdog nodes
Driver doesn't use it yet, but let's describe the HW properly.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20220322095512.4707-2-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Biju Das [Sat, 2 Apr 2022 07:30:34 +0000 (08:30 +0100)]
dt-bindings: clock: Add R9A07G043 CPG Clock and Reset Definitions
Define RZ/G2UL (R9A07G043U) Clock Pulse Generator Core Clock and module
clock outputs, as listed in Table 7.1.4.2 ("Clock List r0.51") and also
add Reset definitions referring to registers CPG_RST_* in Section 7.2.3
("Register configuration") of the RZ/G2UL Hardware User's Manual (Rev.
0.51, Nov. 2021).
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220402073037.23947-3-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Biju Das [Sat, 2 Apr 2022 07:32:34 +0000 (08:32 +0100)]
dt-bindings: arm: renesas: Document Renesas RZ/G2UL SMARC EVK
Document the Renesas SMARC EVK board which is based on the Renesas
RZ/G2UL Type-1 (R9A07G043U11) SoC. The SMARC EVK consists of an
RZ/G2UL Type-1 SoM module and a SMARC carrier board. The SoM module
sits on top of the carrier board.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20220402073234.24625-1-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tony Lindgren [Fri, 4 Feb 2022 08:43:38 +0000 (10:43 +0200)]
ARM: dts: Drop custom clkctrl compatible and update omap5 l4per
We can now use the clock-output-names and don't need custom compatible
values for each clkctrl instance. And we can use a generic name also for
the clock manager instance.
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Tero Kristo <kristo@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Message-Id: <
20220204084339.12341-5-tony@atomide.com>
Tony Lindgren [Fri, 4 Feb 2022 08:43:37 +0000 (10:43 +0200)]
ARM: dts: Add clock-output-names for omap5
To stop using the non-standard node name based clock naming, let's
first add the clock-output-names property. This allows us to stop using
the internal legacy clock naming and unify the naming for the TI SoCs in
the following patches.
Note that we must wait on fixing the node naming issues until after the
internal clock names have been updated to avoid adding name translation
unnecessarily.
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Tero Kristo <kristo@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Message-Id: <
20220204084339.12341-4-tony@atomide.com>
Tony Lindgren [Fri, 4 Feb 2022 08:43:36 +0000 (10:43 +0200)]
ARM: dts: Drop custom clkctrl compatible and update omap4 l4per
We can now use the clock-output-names and don't need custom compatible
values for each clkctrl instance. And we can use a generic name also for
the clock manager instance.
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Tero Kristo <kristo@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Message-Id: <
20220204084339.12341-3-tony@atomide.com>
Tony Lindgren [Fri, 4 Feb 2022 08:43:35 +0000 (10:43 +0200)]
ARM: dts: Add clock-output-names for omap4
To stop using the non-standard node name based clock naming, let's
first add the clock-output-names property. This allows us to stop using
the internal legacy clock naming and unify the naming for the TI SoCs in
the following patches.
Note that we must wait on fixing the node naming issues until after the
internal clock names have been updated to avoid adding name translation
unnecessarily.
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Tero Kristo <kristo@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Message-Id: <
20220204084339.12341-2-tony@atomide.com>
Tony Lindgren [Fri, 4 Feb 2022 08:15:29 +0000 (10:15 +0200)]
ARM: dts: Use clock-output-names for am4
With the TI clocks supporting the use of clock-output-names devicetree
property, we no longer need to use non-standard node names for clocks.
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Tero Kristo <kristo@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Message-Id: <
20220204081529.57694-1-tony@atomide.com>
Tony Lindgren [Fri, 4 Feb 2022 08:08:42 +0000 (10:08 +0200)]
ARM: dts: Use clock-output-names for dra7
With the TI clocks supporting the use of clock-output-names devicetree
property, we no longer need to use non-standard node names for clocks.
Depends-on:
31aa7056bbec ("ARM: dts: Don't use legacy clock defines for dra7 clkctrl")
Depends-on:
9206a3af4fc0 ("clk: ti: Move dra7 clock devices out of the legacy section")
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Tero Kristo <kristo@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Message-Id: <
20220204080842.40673-1-tony@atomide.com>
Tony Lindgren [Fri, 4 Feb 2022 07:33:33 +0000 (09:33 +0200)]
ARM: dts: Use clock-output-names for am3
With the TI clocks supporting the use of clock-output-names devicetree
property, we no longer need to use non-standard node names for clocks.
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Tero Kristo <kristo@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Message-Id: <
20220204073333.18175-5-tony@atomide.com>
Tony Lindgren [Fri, 4 Feb 2022 07:33:32 +0000 (09:33 +0200)]
ARM: dts: Add clksel node for am3 clkout
Let's add a clksel node for the component clocks to avoid devicetree
unique_unit_address warnings. The component clocks can now get IO address
from the parent clksel node.
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Tero Kristo <kristo@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Message-Id: <
20220204073333.18175-4-tony@atomide.com>
Tony Lindgren [Fri, 4 Feb 2022 07:33:31 +0000 (09:33 +0200)]
ARM: dts: Add clksel node for am3 gfx
Let's add a clksel node for the component clocks to avoid devicetree
unique_unit_address warnings. The component clocks can now get IO address
from the parent clksel node.
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Tero Kristo <kristo@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Message-Id: <
20220204073333.18175-3-tony@atomide.com>
Tony Lindgren [Fri, 4 Feb 2022 07:33:30 +0000 (09:33 +0200)]
ARM: dts: Add clksel node for am3 ehrpwm
Let's add a clksel node for the component clocks to avoid devicetree
unique_unit_address warnings. The component clocks can now get IO address
from the parent clksel node.
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Tero Kristo <kristo@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Message-Id: <
20220204073333.18175-2-tony@atomide.com>
Tony Lindgren [Thu, 3 Feb 2022 11:23:37 +0000 (13:23 +0200)]
dt-bindings: clock: ti: Add clock-output-names for TI composite clocks
For the TI composite clocks, we currently have only the divider clock
list clock-output-names as an optional devicetree property. Let's add
clock-output-names for all the TI composite clock bindings.
This allows us to use clock-output-names for the clockctrl instance name
instead of relying on a custom compatible or non-standard node names.
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Tero Kristo <kristo@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Rob Herring <robh@kernel.org>
Message-Id: <
20220203112337.19821-3-tony@atomide.com>
Tony Lindgren [Thu, 3 Feb 2022 11:23:36 +0000 (13:23 +0200)]
dt-bindings: clock: ti: Add clock-output-names for clockctrl
This allows us to use clock-output-names for the clockctrl instance
name instead of relying on a custom compatible or non-standard node
names.
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Tero Kristo <kristo@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Rob Herring <robh@kernel.org>
Message-Id: <
20220203112337.19821-2-tony@atomide.com>
Tony Lindgren [Thu, 3 Feb 2022 11:23:35 +0000 (13:23 +0200)]
dt-bindings: omap: Add clock-output-names and #clock-cells
This allows us to use clock-output-names for the clock manager instance
name instead of relying on non-standard node names.
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Tero Kristo <kristo@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Rob Herring <robh@kernel.org>
Message-Id: <
20220203112337.19821-1-tony@atomide.com>
Christian Hewitt [Sat, 9 Apr 2022 06:42:57 +0000 (06:42 +0000)]
arm64: dts: meson: alpa sort the board Makefile
Let's alpha-sort the board Makefile to keep things organised.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20220409064257.24453-1-christianshewitt@gmail.com
Geert Uytterhoeven [Thu, 3 Feb 2022 15:26:49 +0000 (16:26 +0100)]
arm64: dts: renesas: spider: Add Ethernet sub-board
Add a DTS file for the Spider Ether TSN sub-board (RTP8A779F0ASKB0ST0S),
and include it from the main r8a779f0-spider.dts.
For now its contents are limited to the Board ID EEPROM.
Extracted from a larger patch in the BSP by LUU HOAI.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/5aa58816182b34d9e5795bc1e22784f4e4879d13.1643898884.git.geert+renesas@glider.be
Geert Uytterhoeven [Thu, 3 Feb 2022 15:26:48 +0000 (16:26 +0100)]
arm64: dts: renesas: spider-cpu: Add I2C4 and EEPROMs
Enable the I2C4 bus on the Falcon CPU board, and describe the I2C EEPROMs
present on the Spider CPU and BreakOut boards.
Extracted from a larger patch in the BSP by LUU HOAI.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/6d8917e49f83b6a932970ca169100eb086d11f16.1643898884.git.geert+renesas@glider.be
Geert Uytterhoeven [Thu, 3 Feb 2022 15:26:47 +0000 (16:26 +0100)]
arm64: dts: renesas: r8a779f0: Add I2C nodes
Add device nodes for the I2C Bus Interfaces on the Renesas R-Car S4-8
(R8A779F0) SoC.
Based on a larger patch in the BSP by LUU HOAI.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/e1c7fb17801bc82a74aa5364212d02ba51535dd2.1643898884.git.geert+renesas@glider.be
Krzysztof Kozlowski [Sun, 27 Mar 2022 18:08:54 +0000 (11:08 -0700)]
ARM: dts: s5pv210: align DMA channels with dtschema
dtschema expects DMA channels in specific order (tx, rx and tx-sec).
The order actually should not matter because dma-names is used however
let's make it aligned with dtschema to suppress warnings like:
i2s@
eee30000: dma-names: ['rx', 'tx', 'tx-sec'] is not valid under any of the given schemas
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Co-developed-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Link: https://lore.kernel.org/r/CY4PR04MB056779A9C50DC95987C5272ACB1C9@CY4PR04MB0567.namprd04.prod.outlook.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Jonathan Bakker [Sun, 27 Mar 2022 18:08:53 +0000 (11:08 -0700)]
ARM: dts: s5pv210: Adjust DMA node names to match spec
DMA node names should be dma-controller according to the DT spec,
so rename them from pdma/mdma. Prevents warnings when running
make dtbs_check
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Link: https://lore.kernel.org/r/CY4PR04MB0567F52ABAE0A3CCD3C7CE59CB1C9@CY4PR04MB0567.namprd04.prod.outlook.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Jonathan Bakker [Sun, 27 Mar 2022 18:08:52 +0000 (11:08 -0700)]
ARM: dts: s5pv210: Adjust memory reg entries to match spec
The reg property of memory nodes should have pairs of offset, size;
not all memory banks lumped in as one.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Link: https://lore.kernel.org/r/CY4PR04MB05677849A13F41BF603906DFCB1C9@CY4PR04MB0567.namprd04.prod.outlook.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Jonathan Bakker [Sun, 27 Mar 2022 18:08:51 +0000 (11:08 -0700)]
ARM: dts: s5pv210: Correct interrupt name for bluetooth in Aries
Correct the name of the bluetooth interrupt from host-wake to
host-wakeup.
Fixes:
1c65b6184441b ("ARM: dts: s5pv210: Correct BCM4329 bluetooth node")
Cc: <stable@vger.kernel.org>
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Link: https://lore.kernel.org/r/CY4PR04MB0567495CFCBDC8D408D44199CB1C9@CY4PR04MB0567.namprd04.prod.outlook.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Jonathan Bakker [Sun, 27 Mar 2022 18:08:50 +0000 (11:08 -0700)]
ARM: dts: s5pv210: Remove spi-cs-high on panel in Aries
Since commit
766c6b63aa04 ("spi: fix client driver breakages when using
GPIO descriptors"), the panel has been blank due to an inverted CS GPIO.
In order to correct this, drop the spi-cs-high from the panel SPI device.
Fixes:
766c6b63aa04 ("spi: fix client driver breakages when using GPIO descriptors")
Cc: <stable@vger.kernel.org>
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Link: https://lore.kernel.org/r/CY4PR04MB05670C771062570E911AF3B4CB1C9@CY4PR04MB0567.namprd04.prod.outlook.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>