MIPS: Apply `.insn' to fixup labels throughout

Fix the issue with the ISA bit being lost in fixups that jump to labels
placed just before a section switch.  Such a switch leads to the ISA bit
being lost, because GAS concludes there is no code that follows and
therefore the label refers to data.  Use the `.insn' pseudo-op to
convince the tool this is not the case.

This lack of label annotation leads to microMIPS compilation errors
like:

mips-linux-gnu-ld: arch/mips/built-in.o: .fixup+0x3b8: Unsupported jump between ISA modes; consider recompiling with interlinking enabled.
mips-linux-gnu-ld: final link failed: Bad value

Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com>
Signed-off-by: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8483/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: Fix microMIPS LL/SC immediate offsets

In the microMIPS encoding some memory access instructions have their
immediate offset reduced to 12 bits only.  That does not match the GCC
`R' constraint we use in some places to satisfy the requirement,
resulting in build failures like this:

{standard input}: Assembler messages:
{standard input}:720: Error: macro used $at after ".set noat"
{standard input}:720: Warning: macro instruction expanded into multiple instructions

Fix the problem by defining a macro, `GCC_OFF12_ASM', that expands to
the right constraint depending on whether microMIPS or standard MIPS
code is produced.  Also apply the fix to where `m' is used as in the
worst case this change does nothing, e.g. where the pointer was already
in a register such as a function argument and no further offset was
requested, and in the best case it avoids an extraneous sequence of up
to two instructions to load the high 20 bits of the address in the LL/SC
loop.  This reduces the risk of lock contention that is the higher the
more instructions there are in the critical section between LL and SC.

Strictly speaking we could just bulk-replace `R' with `ZC' as the latter
constraint adjusts automatically depending on the ISA selected.
However it was only introduced with GCC 4.9 and we keep supporing older
compilers for the standard MIPS configuration, hence the slightly more
complicated approach I chose.

The choice of a zero-argument function-like rather than an object-like
macro was made so that it does not look like a function call taking the
C expression used for the constraint as an argument.  This is so as not
to confuse the reader or formatting checkers like `checkpatch.pl' and
follows previous practice.

Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com>
Signed-off-by: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8482/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: Kconfig: Only allow 32-bit microMIPS builds

Only allow 32-bit microMIPS builds, we're not ready yet for 64-bit
microMIPS support.

QEMU does have support for the 64-bit microMIPS ISA and with minor
tweaks it is possible to have a 64-bit processor emulated there that
runs microMIPS code, so despite the lack of actual 64-bit microMIPS
hardware there is a way to run 64-bit microMIPS Linux, but it can all be
considered early development and we are not there yet.  Userland tools
are lacking too, e.g. GCC produces bad code:

{standard input}: Assembler messages:
{standard input}:380: Warning: wrong size instruction in a 16-bit branch delay slot

And our build fails early on, so disable the configuration, for the sake
of automatic random config checkers if nothing else.  Whoever needs to
experiment with 64-bit microMIPS support can revert this change easily.

Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8481/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: signal.c: Fix an invalid cast in ISA mode bit handling

Fix:

arch/mips/kernel/signal.c: In function 'handle_signal':
arch/mips/kernel/signal.c:533:21: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
  unsigned int tmp = (unsigned int)current->mm->context.vdso;
                     ^
arch/mips/kernel/signal.c:536:9: error: cast to pointer from integer of different size [-Werror=int-to-pointer-cast]
  vdso = (void *)tmp;
         ^
cc1: all warnings being treated as errors

when building a 64-bit kernel.

This is not really a supported configuration, but the cast is wrong
either way, Linux makes the assumption that sizeof(void *) equals
sizeof(unsigned long) and therefore the latter type is expected to be
used where integer operations have to be applied to pointers for some
reason.

Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8480/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: mm: Only build one microassembler that is suitable

The microMIPS microassembler is only suitable for configurations where
the kernel itself is built to microMIPS machine code and not where only
user microMIPS software is supported.  The former is controlled with the
CPU_MICROMIPS configuration setting, whereas SYS_SUPPORTS_MICROMIPS is
used for the latter.

Not only that, but with a given microMIPS vs standard MIPS kernel
configuration only one microassembler is needed, that matches the ISA
selected -- CP0.Config3.ISAOnExc is mandatory on microMIPS processors,
so there is never a need to mix microMIPS and standard MIPS code.

Consequently build only the microassembler that matches the ISA selected
for the kernel.

Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8479/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: Kconfig: Enable microMIPS support for Malta

Add missing microMIPS support to Malta.  Currently the kernel only
enables support for the instruction set for the SEAD-3 board despite the
fact processor features have nothing to do with the board a processor is
installed in.

In this case there is no way to run microMIPS software in a fully
supported way under Linux on QEMU.  QEMU supports the emulation of a
Malta board, but does not emulate SEAD-3.  Linux supports running
microMIPS code on a SEAD-3 board, but hardcodes such support to off on
an emulated Malta board even if the processor selected has the microMIPS
instruction set implemented.

Adding support for the SEAD-3 to QEMU is a major project.  Flipping a
bit in the kernel that shouldn't have been cleared in the first place is
a trivial effort.  Thus the answer is plain...

Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8478/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: loongson: common: rtc: make loongson_rtc_resources static

Make loongson_rtc_resources static to eliminate the following
sparse warning:
warning: symbol 'loongson_rtc_resources' was not declared. Should it be static?

Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8529/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: loongson: common: init: Add a missing include

Add a missing include to eliminate the following sparse warnings:
warning: symbol 'prom_init' was not declared. Should it be static?
warning: symbol 'prom_free_prom_memory' was not declared. Should it be static?

Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8531/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: loongson: lemote-2f: reset: make ml2f_reboot static

Make ml2f_reboot static to elimite the following sparse warning:
warning: symbol 'ml2f_reboot' was not declared. Should it be static?

Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8528/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: loongson: lemote-2f: irq: Make internal data static

Make internal static to eliminate the following sparse warnings:
warning: symbol 'ip6_irqaction' was not declared. Should it be static?
warning: symbol 'cascade_irqaction' was not declared. Should it be static?

Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8527/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: loongson: common: Setup: add a missing include

Add a missing include to get rid of the following sparse warning:
warning: symbol 'plat_mem_setup' was not declared. Should it be static?

Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8530/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: Loongson: cs5536_pci: Add a missing include

Add a missing include to get rid of the following sparse warnings:
warning: symbol 'cs5536_pci_conf_write4' was not declared. Should it be static?
warning: symbol 'cs5536_pci_conf_read4' was not declared. Should it be static?

Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8526/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: Loongson: common: Fix array initializer syntax.

Fix array initializer syntax to get rid of the following sparse warnings:
"obsolete array initializer, use C99 syntax".

Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8525/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: uaccess.h: Fix strnlen_user comment.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: IP22/IP32: Add line to arch/mips/Makefile archhelp about vmlinux.32

Building a 64bit kernel for the SGI O2 (IP32) and the SGI Indy (IP22) uses
the 'vmlinux.32' target, which converts the output 64-bit 'vmlinux' image
into a 32-bit wrapped image.  This is needed for certain revisions of the
IP22 and IP32 ARCS PROMs to boot correctly, but this target is missing
from the 'archhelp' info that is emitted by 'make help'.

Signed-off-by: Joshua Kinard <kumba@gentoo.org>
Cc: Linux MIPS List <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/7991/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: lib: mips-atomic.c: Remove obsolete ifdefery

Having #ifdefs just to guard comments is not really helpful
so drop them. Moreover, the code wasn't really reached anyway
since there is a #ifndef CONFIG_CPU_MIPSR2 on the top of the file.

Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8513/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: Octeon: Mark octeon_model_get_string() with __init

Mark octeon_model_get_string() with __init and make internal functions
static.

Signed-off-by: Aaro Koskinen <aaro.koskinen@nsn.com>
Cc: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7668/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: Octeon: Move code to avoid forward declaration

Move code to avoid forward declarations.

Signed-off-by: Aaro Koskinen <aaro.koskinen@nsn.com>
Cc: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7667/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: Octeon: Delete potentially dangerous feature checks

We should not need to read fuses during normal operation, also the current
code has issues with that (not safe for concurrent access). Since there
are no in-kernel users for these, just delete them. Drivers should
not need such OCTEON_HAS_FEATURE mechanism in any case, instead the
information should be passed via device tree.

Signed-off-by: Aaro Koskinen <aaro.koskinen@nsn.com>
Cc: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7665/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: Octeon: Move cvmx_fuse_read_byte()

Move cvmx_fuse_read_byte() into a .c file.

Signed-off-by: Aaro Koskinen <aaro.koskinen@nsn.com>
Cc: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Cc: Aaro Koskinen <aaro.koskinen@nsn.com>
Patchwork: https://patchwork.linux-mips.org/patch/7666/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: oprofile: Backtrace: don't fail on leaf functions

Continue the backtrace if we cannot find SP adjustment and RA save. In
that case, just assume the current RA. This allows us to get samples of
frequent callers of e.g. GLIBC memset().

Signed-off-by: Aaro Koskinen <aaro.koskinen@nsn.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8109/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: oprofile: Enable backtrace on timer-based profiling

Allow unsupported CPU types to use backtrace with timer-based profiling.
Some CPUs (notably OCTEON) lack architecture-specific oprofile driver. In
such case oprofile can fallback to timer-based mode, and arch code can
still provide the backtrace functionality. So just set up the backtrace
hook always.

Signed-off-by: Aaro Koskinen <aaro.koskinen@nsn.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8108/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: traps: Dump the PageGrain and Wired registers on MC

They can be useful to determine how the MMU is configured on a MC
exception.

Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8401/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: traps: Dump the HTW registers on a MC exception

The HTW registers can be useful to debug a MC exception.

Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8400/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: traps: Replace printk with pr_err for MC exceptions

printk should not be used without a KERN_ facility level

Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8399/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

clocksource: mips-gic: Add device-tree support

Parse the GIC timer frequency and interrupt from the device-tree.

Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: John Crispin <blogic@openwrt.org>
Cc: David Daney <ddaney.cavm@gmail.com>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8421/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

irqchip: mips-gic: Add device-tree support

Add device-tree support for the MIPS GIC.  Update the GIC irqdomain's
xlate() callback to handle the three-cell specifier described in the
MIPS GIC binding document.

Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: John Crispin <blogic@openwrt.org>
Cc: David Daney <ddaney.cavm@gmail.com>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8422/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

of: Add binding document for MIPS GIC

The Global Interrupt Controller (GIC) present on certain MIPS systems
can be used to route external interrupts to individual VPEs and CPU
interrupt vectors.  It also supports a timer and software-generated
interrupts.

Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: John Crispin <blogic@openwrt.org>
Cc: David Daney <ddaney.cavm@gmail.com>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8420/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: ath79: Read the initrd address from the firmware environment

Allow loading an initrd passed by the firmware.

Signed-off-by: Alban Bedel <albeu@free.fr>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8354/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: ath79: Use the firmware lib to parse the kernel command line

No need to duplicate code that is available in the firmware library.
It also give us access to the firmware environment which is needed
to read the initrd address and size.

Signed-off-by: Alban Bedel <albeu@free.fr>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8353/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: ath25: add Wireless device support

Atheros AR5312 and AR2315 both have a builtin wireless device, this
patch add helper code and register platform device for all supported
WiSoCs.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Cc: Linux MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/8249/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

ath5k: update dependencies

- Use config symbol defined in the driver instead of arch specific one for
  conditional compilation.
- Rename the ATHEROS_AR231X config symbol to ATH25.
- Fix include (ar231x_platform.h -> ath25_platform.h).
- Some of AR231x SoCs (e.g. AR2315) have PCI bus support, so remove !PCI
  dependency, which block AHB support build.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Acked-by: John W. Linville <linville@tuxdriver.com>
Cc: Jiri Slaby <jirislaby@gmail.com>
Cc: Nick Kossifidis <mickflemm@gmail.com>
Cc: "Luis R. Rodriguez" <mcgrof@do-not-panic.com>
Cc: linux-wireless@vger.kernel.org
Cc: ath5k-devel@lists.ath5k.org
Cc: Linux MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/8248/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

ath5k: revert AHB bus support removing

This reverts commit 093ec3c5337434f40d77c1af06c139da3e5ba6dc.

AHB bus code has been removed, since we did not have support Atheros
AR231x SoC, required for building the AHB version of ath5k. Now that
support WiSoC chips added we can restore functionality back.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Acked-by: John W. Linville <linville@tuxdriver.com>
Cc: Jiri Slaby <jirislaby@gmail.com>
Cc: Nick Kossifidis <mickflemm@gmail.com>
Cc: "Luis R. Rodriguez" <mcgrof@do-not-panic.com>
Cc: linux-wireless@vger.kernel.org
Cc: ath5k-devel@lists.ath5k.org
Cc: Linux MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/8247/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: ath25: add AR2315 PCI host controller driver

Add PCI host controller driver and DMA address calculation hook.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Cc: Linux MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/8246/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: ath25: register AR5312 flash controller

AR5312 SoC flash controller maps the flash content to memory and
translates the memory access operations to the flash access operations.
Such controller is fully supported by the physmap-flash driver.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>R5312 SoC flash
Cc: Linux MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/8245/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: ath25: add SoC type detection

Detect SoC type based on device ID and board configuration data.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Cc: Linux MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/8244/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: ath25: add board configuration detection

All boards based on AR5312/AR2315 SoC have a special structure located
at the end of flash. This structure contains board-specific data such as
Ethernet and Wireless MAC addresses. The flash is mapped to the memmory
at predefined location.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Cc: Linux MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/8243/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: ath25: add UART support

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Cc: Linux MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/8242/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: ath25: add early printk support

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Cc: Linux MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/8241/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: ath25: add interrupts handling routines

Add interrupts initialization and handling routines, also add AHB bus
error interrupt handlers for both SoCs families.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Cc: Linux MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/8240/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: ath25: Add basic AR2315 SoC support

Add basic support for Atheros AR2315+ SoCs: registers definition file
and initial setup code.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Cc: Linux MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/8239/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: ath25: add basic AR5312 SoC support

Add basic support for Atheros AR5312/AR2312 SoCs: registers definition
file and initial setup code.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Cc: Linux MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/8238/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: ath25: add common parts

Add common code for Atheros AR5312 and Atheros AR2315 SoCs families.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Cc: Linux MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/8237
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: FW: Use kstrtoul() to parse unsigned long from the fw environment

Fix some value corruptions with values that can't be represented in a
signed long.

Signed-off-by: Alban Bedel <albeu@free.fr>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8358/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: FW: Fix parsing u-boot environment

When reading u-boot's key=value pairs it should skip the '=' and not
use the next argument.

Signed-off-by: Alban Bedel <albeu@free.fr>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8357/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

TC: Error handling clean-ups

Rewrite TURBOchannel error handling to use a common failure path, making
sure put_device is called for devices that failed initialization.  While
at it update printk calls to use pr_err rather than KERN_ERR.

Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6701/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: ralink: add rt2880 pci driver

Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/8034/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: ralink: allow loading irq registers from the devicetree

Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/8029/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: ralink: add mt7628an support

Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/8031/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: ralink: add support for MT7620n

This is the small version of MT7620a.

Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/8030/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: ralink: cleanup early_printk

Add support for the new MT7621/8 SoC and kill ifdefs.
Cleanup some whitespace error while we are at it.

Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/8028/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: ralink: cleanup the soc specific pinmux data

Before we had a pinctrl driver we used a custom OF api. This patch converts the
soc specific pinmux data to a new set of structs. We also add some new pinmux
setings.

Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/8009/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: ralink: copy the commandline from the devicetree

This is a regression caused by:
commit afb46f7996e91aeb36e07bc92cf96e8045bec00e
Author: Rob Herring <robh@kernel.org>
Date:   Wed Apr 2 19:07:24 2014 -0500
mips: ralink: convert to use unflatten_and_copy_device_tree

Make the of init code reuse the cmdline defined inside the dts.

Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/8008/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: ralink: add a bootrom dumper module

This patch adds a trivial driver that allows userland to extract the bootrom of
a SoC via debugfs.

Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/8002/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: ralink: add rt3883 wmac clock

Register the wireless mac clock on rti3883. This is required by the wifi driver.

Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/8007/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: ralink: add rt2880 wmac clock

Register the wireleass mac clock on rt2880. This is required by the wifi driver.

Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/8006/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: ralink: add missing clk_set_rate() to clk.c

This function was missing causing make allmod to fail.

Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/8005/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: ralink: allow manual memory override

RT5350 relies on the bootloader setting up the memc correctly. On some boards
the setup is incorrect leading to 32 MB being available but only 16 MB being
recognized. Allow these boards to manually override the memory range.

Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/8004/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: ralink: add illegal access driver

These SoCs have a special irq that fires upon an illegal memmory access.

Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/8003/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: ralink: add rt_sysc_m32 helper

We already have a read and write wrapper. This adds the missing mask wrapper.

Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/8001/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: ralink: add a helper for reading the ECO version

Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/8000/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: ralink: add verbose pmu info

Print the PMU and LDO settings on boot.

Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/7999/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: lantiq: add missing spi clock on falcon SoC

Signed-off-by: Thomas Langer <thomas.langer@lantiq.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/8050/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: lantiq: the detection of the gpe clock is broken

The code to detect unfused SoCs was broken due to missing register masking.

Signed-off-by: Thomas Langer <thomas.langer@lantiq.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/8049/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: lantiq: copy the commandline from the devicetree

This is a regression caused by:
commit afb46f7996e91aeb36e07bc92cf96e8045bec00e
Author: Rob Herring <robh@kernel.org>
Date:   Wed Apr 2 19:07:24 2014 -0500
mips: ralink: convert to use unflatten_and_copy_device_tree

Make the of init code reuse the cmdline defined inside the dts.

Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/8048/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: lantiq: move eiu init after irq_domain register

The eiu init failed as the irq_domain was not yet available.

Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/8047/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: lantiq: export soc type

The voice and dsl drivers need to know which SoC we are running on.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Patchwork: http://patchwork.linux-mips.org/patch/8046/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: lantiq: add support for xrx200 firmware depending on soc type

VR9 needs different firmware files for the various phy/soc revisions. Some
boards are ship with older and newer SoC revisions. To be able to boot a single
image on all versions we need to define both firmware files inside the
devicetree.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/8045/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: lantiq: reboot gphy on restart

A reboot sometimes lead to a none working phy. An explicit reboot fixes the
problem.

Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/8044/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: lantiq: add reset-controller api support

Add a reset-controller binding for the reset registers found on the lantiq
SoC.

Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/8043/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: lantiq: handle vmmc memory reservation

The Lantiq SoCs have a 2nd mips core called "voice mips macro core (vmmc)"
which is used to run the voice firmware. This driver allows us to register
a chunk of memory that the voice driver can later use for the 2nd core.

Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/8042/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: Alchemy: Remove direct access to prepare_count field of struct clk

Replacing it with a call to __clk_is_prepared(), which isn't entirely
equivalent but in practice shouldn't matter.

Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Cc: Manuel Lauss <manuel.lauss@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8120/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

clocksource: mips-gic: Bump up rating of GIC timer

Bump up the rating of the GIC timer so that it gets prioritized
over the CP0 timer.

Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8141/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

clocksource: mips-gic: Use clockevents_config_and_register

Use clockevents_config_and_register to setup the clock_event_device
based on frequency and min/max ticks instead of doing it ourselves.

Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8140/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

clocksource: mips-gic: Use CPU notifiers to setup the timer

Instead of requiring an explicit call to gic_clockevent_init in the SMP
startup path, use CPU notifiers to register and enable the GIC timer on
CPU startup.

Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8139/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

clocksource: mips-gic: Use percpu_dev_id

Since the GIC timer IRQ is a percpu IRQ, we can use percpu_dev_id
to pass the IRQ handler the correct clock_event_device.

Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8138/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

clocksource: mips-gic: Remove gic_event_handler

Remove gic_event_handler since it is completely unnecessary.

Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8136/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

clocksource: mips-gic: Move gic_frequency to clocksource driver

There's no reason for gic_frequency to be global any more and it
certainly doesn't belong in the GIC irqchip driver, so move it to
the GIC clocksource driver.

Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8137/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

clocksource: mips-gic: Staticize local symbols

There are a number of variables and functions which are unnecessarily
global.  Mark them static.

Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8135/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

clocksource: mips-gic: Combine with GIC clockevent driver

Combine the GIC clocksource driver with the GIC clockevent driver from
arch/mips/kernel/cevt-gic.c and remove the clockevent driver's separate
Kconfig symbol.

Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8132/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: Move GIC clocksource driver to drivers/clocksource/

Move the GIC clocksource driver to drivers/clocksource/mips-gic-timer.c.

Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8133/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

irqchip: mips-gic: Use GIC_SH_WEDGE_{SET,CLR} macros

Use the GIC_SH_WEDGE_{SET,CLR} macros provided by mips-gic.h.

Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8134/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

irqchip: mips-gic: Remove gic_{pending,itrmask}_regs

There's no reason for the pending and masked interrupt bitmasks
to be global.  Just declare them on the stack in gic_get_int()
since they only consume (256*2)/8 = 64 bytes.

Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8131/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

irqchip: mips-gic: Clean up #includes

Sort the #includes and remove those which are unnecessary.

Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8130/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

irqchip: mips-gic: Clean up header file

Remove duplicate #defines and unnecessary #includes, fix parenthesization,
and re-order register definitions in ascending order.

Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8128/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MAINTAINERS: Add entry for bcm63xx/bcm33xx UDC gadget driver

This hardware shows up on the newly-supported BCM3384 cable chip, as well
as several old BCM63xx DSL chips.

Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Cc: f.fainelli@gmail.com
Cc: mbizon@freebox.fr
Cc: jogo@openwrt.org
Cc: jfraser@broadcom.com
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8172/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MAINTAINERS: Add entry for BCM33xx cable chips

Add myself as a maintainer for the new BCM3384 board support code.

Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Cc: f.fainelli@gmail.com
Cc: mbizon@freebox.fr
Cc: jogo@openwrt.org
Cc: jfraser@broadcom.com
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8171/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: bcm3384: Initial commit of bcm3384 platform support

This supports SMP Linux running on the BCM3384 Zephyr (BMIPS5000)
application processor, with fully functional UART and USB 1.1/2.0.
Device Tree is used to configure the following items:

 - All peripherals
 - Early console base address
 - SMP or UP mode
 - MIPS counter frequency
 - Memory size / regions
 - DMA offset
 - Kernel command line

The DT-enabled bootloader and build instructions are posted at
https://github.com/Broadcom/aeolus

Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Cc: f.fainelli@gmail.com
Cc: mbizon@freebox.fr
Cc: jogo@openwrt.org
Cc: jfraser@broadcom.com
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8170/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Documentation: DT: Add "mti" vendor prefix

We have a bunch of platforms using "mti,cpu-interrupt-controller" but
the "mti" prefix isn't documented.  Fix this.

Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Cc: f.fainelli@gmail.com
Cc: mbizon@freebox.fr
Cc: jogo@openwrt.org
Cc: jfraser@broadcom.com
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8169/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Documentation: DT: Add entries for BCM3384 and its peripherals

This covers the new "brcm,*" devices added in the upcoming bcm3384 commit.

Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Cc: f.fainelli@gmail.com
Cc: mbizon@freebox.fr
Cc: jogo@openwrt.org
Cc: jfraser@broadcom.com
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8168/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: Create a helper function for DT setup

A couple of platforms register two buses and call of_platform_populate().
Move this into a common function to reduce duplication.

Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Cc: f.fainelli@gmail.com
Cc: mbizon@freebox.fr
Cc: jogo@openwrt.org
Cc: jfraser@broadcom.com
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8167/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: BMIPS: Add PRId for BMIPS5200 (Whirlwind)

This is a dual core (quad thread) BMIPS5000.  It needs a little extra
code to boot the second core (CPU2/CPU3), but for now we can treat it the
same as a single core BMIPS5000.

Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Cc: f.fainelli@gmail.com
Cc: mbizon@freebox.fr
Cc: jogo@openwrt.org
Cc: jfraser@broadcom.com
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8166/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: BMIPS: Add special cache handling in c-r4k.c

BMIPS435x and BMIPS438x have a single shared L1 D$ and load/store unit,
so it isn't necessary to raise IPIs to keep both CPUs coherent.

BMIPS5000 has VIPT L1 caches that handle aliases in hardware, and its I$
fills from D$.  But a special sequence with 2 SYNCs and 32 NOPs is needed
to ensure coherency.

Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Cc: f.fainelli@gmail.com
Cc: mbizon@freebox.fr
Cc: jogo@openwrt.org
Cc: jfraser@broadcom.com
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8165/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: BMIPS: Let each platform customize the CPU1 IRQ mask

On some chips like bcm3384, "other stuff" gets wired up to CPU1's IE_IRQ1
input, generating spurious IRQs.  In this case we want the platform code
to be able to mask it off.

Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Cc: f.fainelli@gmail.com
Cc: mbizon@freebox.fr
Cc: jogo@openwrt.org
Cc: jfraser@broadcom.com
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8163/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: BMIPS: Select the appropriate L1_CACHE_SHIFT for 438x and 5000 CPUs

BMIPS438x has a 64-byte D$ line size and BMIPS5000 has a 128-byte L2
line size.  If L1_CACHE_SHIFT is undersized, DMA buffers will not be
cacheline-aligned and terrible things will happen.

Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Cc: f.fainelli@gmail.com
Cc: mbizon@freebox.fr
Cc: jogo@openwrt.org
Cc: jfraser@broadcom.com
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8164/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: Allow MIPS_CPU_SCACHE to be used with different line sizes

CONFIG_MIPS_CPU_SCACHE determines whether to build sc-mips.c.  However,
it is currently hardwired to use an L1_SHIFT of 6 (64 bytes).  Move the
L1_SHIFT selection into the CPU or SoC section so that other SoCs can
select different values.

Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Cc: f.fainelli@gmail.com
Cc: mbizon@freebox.fr
Cc: jogo@openwrt.org
Cc: jfraser@broadcom.com
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8162/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: BMIPS: Explicitly configure reset vectors prior to secondary boot

The secondary CPU's reset vector needs to be set to KSEG1 for a cold
boot (release from reset), or KSEG0 for a warm restart.  On a cold boot
KSEG0 may be unavailable (BMIPS4380), and on a warm restart KSEG1 may
be unavailable (XKS01 mode on 4380 or 5000).

Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Cc: f.fainelli@gmail.com
Cc: mbizon@freebox.fr
Cc: jogo@openwrt.org
Cc: jfraser@broadcom.com
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8161/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: BMIPS: Mask off timer IRQs when hot-unplugging a CPU

CPU interrupts need to be disabled on a cpu being taken down.
When a cpu is hot-plugged out of the system the following sequence occurs.

On the CPU where the hotplug sequence was initiated:
    cpu_down
        _cpu_down {
            __cpu_notify(CPU_DOWN_PREPARE
            __stop_machine(take_cpu_down
                wait for cpu to run disable code.
            __cpu_die
        }

On the CPU  being disabled:
    take_cpu_down
        __cpu_disable {
            mp_ops->cpu_disable
                bmips_cpu_disable
                    clear_c0_status(IE_IRQ5) (added)
            cpu_notify(CPU_DYING...
        }

Before the cpu_notifier is called with CPU_DYING, all interrupts on the
dying cpu must be disabled.  This guarantees that before tick_notify is
called with the CPU_DYING event and sets the clock device pointer to
NULL, there can not be any more clock interrupts.

When this wasn't done, an unfortunately-timed timer interrupt sometimes
caused hangs immediately prior to system suspend:

    Debug PM is not enabled. To enable partial suspend, rebuild kernel with CONFIG_PM_DEBUG
    Pass 1 out of 1,PM: Syncing filesystems ... mode=none, tp1=done.
    1, flags=5, cycle_tp=, sleep=
    Freezing user space processes ... (elapsed 0.01 seconds) done.
    Freezing remaining freezable tasks ... (elapsed 0.01 seconds) done.
    PM: suspend of devices complete after 54.199 msecs
    PM: late suspend of devices complete after 0.172 msecs
    Disabling non-boot CPUs ...
    SMP: CPU1 is offline
    INFO: rcu_sched detected stalls on CPUs/tasks: { 3} (detected by 0, t=62537 jiffies)
    Call Trace:
    [<804baa78>] dump_stack+0x8/0x34
    [<8008a2d8>] __rcu_pending+0x4b8/0x55c
    [<8008adf4>] rcu_check_callbacks+0x78/0x180
    [<80037830>] update_process_times+0x40/0x6c
    [<80072fe4>] tick_sched_timer+0x74/0xe4
    [<80050180>] __run_hrtimer.clone.30+0x64/0x140
    [<80051150>] hrtimer_interrupt+0x19c/0x4bc
    [<8000cdb8>] c0_compare_interrupt+0x50/0x88
    [<80081b18>] handle_irq_event_percpu+0x5c/0x2f4
    [<80086490>] handle_percpu_irq+0x8c/0xc0
    [<800811b4>] generic_handle_irq+0x34/0x54
    [<800067dc>] do_IRQ+0x18/0x2c
    [<8000375c>] plat_irq_dispatch+0xd0/0x128
    [<80004a04>] ret_from_irq+0x0/0x4
    [<80004c40>] r4k_wait+0x20/0x40
    [<80006b6c>] cpu_idle+0x98/0xf0
    [<805d3988>] start_kernel+0x424/0x440

Signed-off-by: Jon Fraser <jfraser@broadcom.com>
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Cc: f.fainelli@gmail.com
Cc: mbizon@freebox.fr
Cc: jogo@openwrt.org
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8160/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: BMIPS: Allow BMIPS3300 to utilize SMP ebase relocation code

BMIPS3300 processors do not have the hardware to support SMP, but with a
small tweak, the SMP ebase relocation code allows BMIPS3300-based
platforms to reuse the S2/S3 power management code from BMIPS4380-based
chips.  Normally this is as simple as adding one line to prom_init():

    board_ebase_setup = &bmips_ebase_setup;

Signed-off-by: Jon Fraser <jfraser@broadcom.com>
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Cc: f.fainelli@gmail.com
Cc: mbizon@freebox.fr
Cc: jogo@openwrt.org
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8159/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: BMIPS: Introduce helper function to change the reset vector

This will need to be called from a few different places, and the logic
is starting to get a bit hairy (with the need for IPIs, CPU bug
workarounds, and hazards).

Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Cc: f.fainelli@gmail.com
Cc: mbizon@freebox.fr
Cc: jogo@openwrt.org
Cc: jfraser@broadcom.com
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8158/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>