review.tizen.org Git - platform/kernel/linux-stable.git/log

hwmon: (emc1403) Support full range of known chip revision numbers

commit 3a18e1398fc2dc9c32bbdc50664da3a77959a8d1 upstream.

The datasheet for EMC1413/EMC1414, which is fully compatible to
EMC1403/1404 and uses the same chip identification, references revision
numbers 0x01, 0x03, and 0x04. Accept the full range of revision numbers
from 0x01 to 0x04 to make sure none are missed.

Signed-off-by: Josef Gajdusek <atx@atx.name>
[Guenter Roeck: Updated headline and description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

hwmon: (emc1403) Fix resource leak on module unload

commit 8759f9046550f463098148bf577ccd32cdb895e3 upstream.

Commit 454aee17f claims to convert driver emc1403 to use
devm_hwmon_device_register_with_groups, however the patch itself makes
use of hwmon_device_register_with_groups instead. As the driver remove
function was still dropped, the hwmon device is no longer unregistered
on driver removal, leading to a resource leak.

Signed-off-by: Jean Delvare <jdelvare@suse.de>
Fixes: 454aee17f hwmon: (emc1403) Convert to use devm_hwmon_device_register_with_groups
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

hwmon: (emc1403) fix inverted store_hyst()

commit 17c048fc4bd95efea208a1920f169547d8588f1f upstream.

Attempts to set the hysteresis value to a temperature below the target
limit fails with "write error: Numerical result out of range" due to
an inverted comparison.

Signed-off-by: Josef Gajdusek <atx@atx.name>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
[Guenter Roeck: Updated headline and description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Revert "hwmon: (coretemp) Refine TjMax detection"

commit c0940e95f7a78be0525c8d31df0b1f71e149e57e upstream.

This reverts commit 9fb6c9c73b11bef65ba80a362547fd116c1e1c9d.

Tjmax on some Intel CPUs is below 85 degrees C. One known example is
L5630 with Tjmax of 71 degrees C. There are other Xeon processors with
Tjmax of 70 or 80 degrees C. Also, the Intel IA32 System Programming
document states that the temperature target is in bits 23:16 of MSR 0x1a2
(MSR_TEMPERATURE_TARGET), which is 8 bits, not 7.

So even if turbostat uses similar checks to validate Tjmax, there is no
evidence that the checks are actually required. On the contrary, the
checks are known to cause problems and therefore need to be removed.

This fixes https://bugzilla.kernel.org/show_bug.cgi?id=75071.

Fixes: 9fb6c9c hwmon: (coretemp) Refine TjMax detection
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

module: remove warning about waiting module removal.

commit 79465d2fd48e68940c2bdecddbdecd45bbba06fe upstream.

We remove the waiting module removal in commit 3f2b9c9cdf38 (September
2013), but it turns out that modprobe in kmod (< version 16) was
asking for waiting module removal. No one noticed since modprobe would
check for 0 usage immediately before trying to remove the module, and
the race is unlikely.

However, it means that anyone running old (but not ancient) kmod
versions is hitting the printk designed to see if anyone was running
"rmmod -w". All reports so far have been false positives, so remove
the warning.

Fixes: 3f2b9c9cdf389e303b2273679af08aab5f153517
Reported-by: Valerio Vanni <valerio.vanni@inwind.it>
Cc: Elliott, Robert (Server Storage) <Elliott@hp.com>
Acked-by: Lucas De Marchi <lucas.de.marchi@gmail.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

aio: fix potential leak in aio_run_iocb().

commit 754320d6e166d3a12cb4810a452bde00afbd4e9a upstream.

iovec should be reclaimed whenever caller of rw_copy_check_uvector() returns,
but it doesn't hold when failure happens right after aio_setup_vectored_rw().

Fix that in a such way to avoid hairy goto.

Signed-off-by: Leon Yu <chianglungyu@gmail.com>
Signed-off-by: Benjamin LaHaise <bcrl@kvack.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iwlwifi: mvm: delay enabling smart FIFO until after beacon RX

commit 0229cdafb6f67064a217591d48b0f6abf14e8385 upstream.

If we have no beacon data before association, delay smart FIFO
enablement until after we have this data.

Not doing so can cause association failures in extremely silent
environments (usually only a shielded box/room) as beacon RX is
not sent to the host immediately, and then the association time
event ends without the host receiving any beacon even though it
was on the air - it's just stuck on the FIFO.

Fixes: 1f3b0ff8ecce ("iwlwifi: mvm: Add Smart FIFO support")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

hwpoison, hugetlb: lock_page/unlock_page does not match for handling a free hugepage

commit b985194c8c0a130ed155b71662e39f7eaea4876f upstream.

For handling a free hugepage in memory failure, the race will happen if
another thread hwpoisoned this hugepage concurrently. So we need to
check PageHWPoison instead of !PageHWPoison.

If hwpoison_filter(p) returns true or a race happens, then we need to
unlock_page(hpage).

Signed-off-by: Chen Yucong <slaoub@gmail.com>
Reviewed-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Tested-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Reviewed-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

arm64: fix pud_huge() for 2-level pagetables

commit 4797ec2dc83a43be35bad56037d1b53db9e2b5d5 upstream.

The following happens when trying to run a kvm guest on a kernel
configured for 64k pages. This doesn't happen with 4k pages:

  BUG: failure at include/linux/mm.h:297/put_page_testzero()!
  Kernel panic - not syncing: BUG!
  CPU: 2 PID: 4228 Comm: qemu-system-aar Tainted: GF            3.13.0-0.rc7.31.sa2.k32v1.aarch64.debug #1
  Call trace:
  [<fffffe0000096034>] dump_backtrace+0x0/0x16c
  [<fffffe00000961b4>] show_stack+0x14/0x1c
  [<fffffe000066e648>] dump_stack+0x84/0xb0
  [<fffffe0000668678>] panic+0xf4/0x220
  [<fffffe000018ec78>] free_reserved_area+0x0/0x110
  [<fffffe000018edd8>] free_pages+0x50/0x88
  [<fffffe00000a759c>] kvm_free_stage2_pgd+0x30/0x40
  [<fffffe00000a5354>] kvm_arch_destroy_vm+0x18/0x44
  [<fffffe00000a1854>] kvm_put_kvm+0xf0/0x184
  [<fffffe00000a1938>] kvm_vm_release+0x10/0x1c
  [<fffffe00001edc1c>] __fput+0xb0/0x288
  [<fffffe00001ede4c>] ____fput+0xc/0x14
  [<fffffe00000d5a2c>] task_work_run+0xa8/0x11c
  [<fffffe0000095c14>] do_notify_resume+0x54/0x58

In arch/arm/kvm/mmu.c:unmap_range(), we end up doing an extra put_page()
on the stage2 pgd which leads to the BUG in put_page_testzero(). This
happens because a pud_huge() test in unmap_range() returns true when it
should always be false with 2-level pages tables used by 64k pages.
This patch removes support for huge puds if 2-level pagetables are
being used.

Signed-off-by: Mark Salter <msalter@redhat.com>
[catalin.marinas@arm.com: removed #ifndef around PUD_SIZE check]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

x86, mm, hugetlb: Add missing TLB page invalidation for hugetlb_cow()

commit 9844f5462392b53824e8b86726e7c33b5ecbb676 upstream.

The invalidation is required in order to maintain proper semantics
under CoW conditions. In scenarios where a process clones several
threads, a thread operating on a core whose DTLB entry for a
particular hugepage has not been invalidated, will be reading from
the hugepage that belongs to the forked child process, even after
hugetlb_cow().

The thread will not see the updated page as long as the stale DTLB
entry remains cached, the thread attempts to write into the page,
the child process exits, or the thread gets migrated to a different
processor.

Signed-off-by: Anthony Iliopoulos <anthony.iliopoulos@huawei.com>
Link: http://lkml.kernel.org/r/20140514092948.GA17391@server-36.huawei.corp
Suggested-by: Shay Goikhman <shay.goikhman@huawei.com>
Acked-by: Dave Hansen <dave.hansen@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drivers/rtc/rtc-hym8563.c: set uie_unsupported

commit 282cba6b00a95f0277ed71551e3f6b0477e8836b upstream.

The alarm of the hym8563 only supports a minute accuracy, while the uie
wants an alarm one second in the future. Therefore things like the
select() syscall will fail with a timeout, because the next alarm will
happen in a worst case of 60 seconds.

Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mm, thp: close race between mremap() and split_huge_page()

commit dd18dbc2d42af75fffa60c77e0f02220bc329829 upstream.

It's critical for split_huge_page() (and migration) to catch and freeze
all PMDs on rmap walk.  It gets tricky if there's concurrent fork() or
mremap() since usually we copy/move page table entries on dup_mm() or
move_page_tables() without rmap lock taken.  To get it work we rely on
rmap walk order to not miss any entry.  We expect to see destination VMA
after source one to work correctly.

But after switching rmap implementation to interval tree it's not always
possible to preserve expected walk order.

It works fine for dup_mm() since new VMA has the same vma_start_pgoff()
/ vma_last_pgoff() and explicitly insert dst VMA after src one with
vma_interval_tree_insert_after().

But on move_vma() destination VMA can be merged into adjacent one and as
result shifted left in interval tree.  Fortunately, we can detect the
situation and prevent race with rmap walk by moving page table entries
under rmap lock.  See commit 38a76013ad80.

Problem is that we miss the lock when we move transhuge PMD.  Most
likely this bug caused the crash[1].

[1] http://thread.gmane.org/gmane.linux.kernel.mm/96473

Fixes: 108d6642ad81 ("mm anon rmap: remove anon_vma_moveto_tail")

Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reviewed-by: Andrea Arcangeli <aarcange@redhat.com>
Cc: Rik van Riel <riel@redhat.com>
Acked-by: Michel Lespinasse <walken@google.com>
Cc: Dave Jones <davej@redhat.com>
Cc: David Miller <davem@davemloft.net>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mac80211: fix on-channel remain-on-channel

commit b4b177a5556a686909e643f1e9b6434c10de079f upstream.

Jouni reported that if a remain-on-channel was active on the
same channel as the current operating channel, then the ROC
would start, but any frames transmitted using mgmt-tx on the
same channel would get delayed until after the ROC.

The reason for this is that the ROC starts, but doesn't have
any handling for "remain on the same channel", so it stops
the interface queues. The later mgmt-tx then puts the frame
on the interface queues (since it's on the current operating
channel) and thus they get delayed until after the ROC.

To fix this, add some logic to handle remaining on the same
channel specially and not stop the queues etc. in this case.
This not only fixes the bug but also improves behaviour in
this case as data frames etc. can continue to flow.

Reported-by: Jouni Malinen <j@w1.fi>
Tested-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mac80211: fix suspend vs. association race

commit c52666aef9f2dff39276eb53f15d99e2e229870f upstream.

If the association is in progress while we suspend, the
stack will be in a messed up state. Clean it before we
suspend.

This patch completes Johannes's patch:

1a1cb744de160ee70086a77afff605bbc275d291
Author: Johannes Berg <johannes.berg@intel.com>

mac80211: fix suspend vs. authentication race

Fixes: 12e7f517029d ("mac80211: cleanup generic suspend/resume procedures")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mac80211: fix nested rtnl locking on ieee80211_reconfig

commit e669ba2d06c6195662601956454ac959892f0762 upstream.

ieee80211_reconfig already holds rtnl, so calling
cfg80211_sched_scan_stopped results in deadlock.

Use the rtnl-version of this function instead.

Fixes: d43c6b6 ("mac80211: reschedule sched scan after HW restart")
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

cfg80211: add cfg80211_sched_scan_stopped_rtnl

commit 792e6aa7a15ea0fb16f8687e93caede1ea9118c7 upstream.

Add locked-version for cfg80211_sched_scan_stopped.
This is used for some users that might want to
call it when rtnl is already locked.

Fixes: d43c6b6 ("mac80211: reschedule sched scan after HW restart")
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

cfg80211: free sme on connection failures

commit c1fbb258846dfc425507a093922d2d001e54c3ea upstream.

cfg80211 is notified about connection failures by
__cfg80211_connect_result() call. However, this
function currently does not free cfg80211 sme.

This results in hanging connection attempts in some cases

e.g. when mac80211 authentication attempt is denied,
we have this function call:
ieee80211_rx_mgmt_auth() -> cfg80211_rx_mlme_mgmt() ->
cfg80211_process_auth() -> cfg80211_sme_rx_auth() ->
__cfg80211_connect_result()

but cfg80211_sme_free() is never get called.

Fixes: ceca7b712 ("cfg80211: separate internal SME implementation")
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

cfg80211: fix few minor issues in reg_process_hint()

commit 772f0389338cfcf96da1c178046dc7e1649ab554 upstream.

Fix the following issues in reg_process_hint():

1. Add verification that wiphy is valid before processing
NL80211_REGDOMAIN_SET_BY_COUNTRY_IE.
2. Free the request in case of invalid initiator.
3. Remove WARN_ON check on reg_request->alpha2 as it is not a
pointer.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ipmi: Reset the KCS timeout when starting error recovery

commit eb6d78ec213e6938559b801421d64714dafcf4b2 upstream.

The OBF timer in KCS was not reset in one situation when error recovery
was started, resulting in an immediate timeout.

Reported-by: Bodo Stroesser <bstroesser@ts.fujitsu.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ipmi: Fix a race restarting the timer

commit 48e8ac2979920ffa39117e2d725afa3a749bfe8d upstream.

With recent changes it is possible for the timer handler to detect an
idle interface and not start the timer, but the thread to start an
operation at the same time.  The thread will not start the timer in that
instance, resulting in the timer not running.

Instead, move all timer operations under the lock and start the timer in
the thread if it detect non-idle and the timer is not already running.
Moving under locks allows the last timeout to be set in both the thread
and the timer.  'Timer is not running' means that the timer is not
pending and smi_timeout() is not running.  So we need a flag to detect
this correctly.

Also fix a few other timeout bugs: setting the last timeout when the
interrupt has to be disabled and the timer started, and setting the last
timeout in check_start_timer_thread possibly racing with the timer

Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Bodo Stroesser <bstroesser@ts.fujitsu.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

timer: Prevent overflow in apply_slack

commit 98a01e779f3c66b0b11cd7e64d531c0e41c95762 upstream.

On architectures with sizeof(int) < sizeof (long), the
computation of mask inside apply_slack() can be undefined if the
computed bit is > 32.

E.g. with: expires = 0xffffe6f5 and slack = 25, we get:

expires_limit = 0x20000000e
bit = 33
mask = (1 << 33) - 1 /* undefined */

On x86, mask becomes 1 and and the slack is not applied properly.
On s390, mask is -1, expires is set to 0 and the timer fires immediately.

Use 1UL << bit to solve that issue.

Suggested-by: Deborah Townsend <dstownse@us.ibm.com>
Signed-off-by: Jiri Bohac <jbohac@suse.cz>
Link: http://lkml.kernel.org/r/20140418152310.GA13654@midget.suse.cz
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

gpu: host1x: handle the correct # of syncpt regs

commit 22bbd5d949dc7fdd72a4e78e767fa09d8e54b446 upstream.

BIT_WORD() truncates rather than rounds, so the loops in
syncpt_thresh_isr() and _host1x_intr_disable_all_syncpt_intrs() use <=
rather than < in an attempt to process the correct number of registers
when rounding of the conversion of count of bits to count of words is
necessary. However, when rounding isn't necessary because the value is
already a multiple of the divisor (as is the case for all values of
nb_pts the code actually sees), this causes one too many registers to
be processed.

Solve this by using and explicit DIV_ROUND_UP() call, rather than
BIT_WORD(), and comparing with < rather than <=.

Fixes: 7ede0b0bf3e2 ("gpu: host1x: Add syncpoint wait and interrupts")
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-By: Terje Bergstrom <tbergstrom@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iwlwifi: 7000: bump API to 9

commit 431031851ea72a25abb9ad4df56a0f3b997e3026 upstream.

This will allow to load the new firmware.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iwlwifi: mvm: rs: reinit rs if no tx for a long time

commit 87d5e4155c0088e6766b4f0193b63fa0eab71220 upstream.

After being idle for a long time (>5sec) the rs statistics
will be stale so we prefer to reset rs and start from legacy
rates again. This gives better results when the attenuation
increased signficantly (e.g. we got further from the AP) and
after a while we start Tx
Note that the first Tx after the idle period will still go out
in the old modulation and rate but this seemed a simpler approach
compared to adding a timer or modifying mac80211 for this.
The negative impact is negligble as we'll recover quickly.

Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iwlwifi: mvm: rs: fix and cleanup rs_get_rate_action

commit e53839eb9882c99d3781eab0fe1b2d4369a6a2cc upstream.

Change the down/upscale decision logic a bit to be based
on different success ratio thresholds. This fixes the implementation
compared to the rate scale algorithm which was planned to yield
optimal results. Also fix a case where a lower rate wasn't explored
despite being a potential for better throughput.
While at it rewrite rs_get_rate_action to be more clear and clean.

Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iwlwifi: mvm: avoid searching unnecessary columns

commit d8fff919ecd7820084675c2814913445e95640ac upstream.

Don't search columns which are unlikely to succeed as previous
columns searched with less aggressive modulation failed.

Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iwlwifi: mvm: rs: fallback to legacy Tx columns

commit fd7dbee51b3d98402edb11fec0c93d96476e0ae1 upstream.

Allow switching back to legacy Tx columns so we'll stop doing
HT/VHT in case we're far from the AP. Stop active aggregation when
making a deciding to stay in a legacy column.
Despite having low legacy rates in the LQ table lower entries
it doesn't help much in case we're doing aggregations as the
aggregation was being transmitted in the initial rate of the table.

This should help traffic stalls when far from the AP.

Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iwlwifi: add new 7265 HW IDs

commit 80f2679e589503bd6cbaaa1f9c1cd9dd7dfae032 upstream.

Add 2 new HW IDs for the 7265 series.

Signed-off-by: Oren Givon <oren.givon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iwlwifi: mvm: rs: fix mimo delimiter in LQ cmd

commit d9088f60425e0acd8a8f05fdfcfdd288d3258641 upstream.

mimo_delim was always set to 0 instead of pointing to
the first SISO entry after MIMO rates.
This can cause keep transmitting in MIMO even when we shouldn't.
For example when the peer is requesting static SMPS.

Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iwlwifi: add MODULE_FIRMWARE for 7265

commit 08a732f4e4a842f0101e5ea03d79e9d613ffadbe upstream.

It was missing.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

8250_core: Fix unwanted TX chars write

commit b08c9c317e3f7764a91d522cd031639ba42b98cc upstream.

On transmit-hold-register empty, serial8250_tx_chars
should be called only if we don't use DMA.
DMA has its own tx cycle.

Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: 8250: Fix thread unsafe __dma_tx_complete function

commit f8fd1b0350d3a4581125f5eda6528f5a2c5f9183 upstream.

__dma_tx_complete is not protected against concurrent
call of serial8250_tx_dma. it can lead to circular tail
index corruption or parallel call of serial_tx_dma on the
same data portion.

This patch fixes this issue by holding the port lock.

Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mm: make fixup_user_fault() check the vma access rights too

commit 1b17844b29ae042576bea588164f2f1e9590a8bc upstream.

fixup_user_fault() is used by the futex code when the direct user access
fails, and the futex code wants it to either map in the page in a usable
form or return an error.  It relied on handle_mm_fault() to map the
page, and correctly checked the error return from that, but while that
does map the page, it doesn't actually guarantee that the page will be
mapped with sufficient permissions to be then accessed.

So do the appropriate tests of the vma access rights by hand.

[ Side note: arguably handle_mm_fault() could just do that itself, but
  we have traditionally done it in the caller, because some callers -
  notably get_user_pages() - have been able to access pages even when
  they are mapped with PROT_NONE.  Maybe we should re-visit that design
  decision, but in the meantime this is the minimal patch. ]

Found by Dave Jones running his trinity tool.

Reported-by: Dave Jones <davej@redhat.com>
Acked-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

topology: Fix compilation warning when not in SMP

commit 53974e06603977f348ed978d75c426b0532daa67 upstream.

The topology_##name() macro does not use its argument when CONFIG_SMP is not
set, as it ultimately calls the cpu_data() macro.

So we avoid maintaining a possibly unused `cpu' variable, to avoid the
following compilation warning:

  drivers/base/topology.c: In function ‘show_physical_package_id’:
  drivers/base/topology.c:103:118: warning: unused variable ‘cpu’ [-Wunused-variable]
   define_id_show_func(physical_package_id);

  drivers/base/topology.c: In function ‘show_core_id’:
  drivers/base/topology.c:106:106: warning: unused variable ‘cpu’ [-Wunused-variable]
   define_id_show_func(core_id);

This can be seen with e.g. x86 defconfig and CONFIG_SMP not set.

Signed-off-by: Vincent Stehlé <vincent.stehle@laposte.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

coredump: fix va_list corruption

commit 404ca80eb5c2727d78cd517d12108b040c522e12 upstream.

A va_list needs to be copied in case it needs to be used twice.

Thanks to Hugh for debugging this issue, leading to various panics.

Tested:

  lpq84:~# echo "|/foobar12345 %h %h %h %h %h %h %h %h %h %h %h %h %h %h %h %h %h %h %h %h" >/proc/sys/kernel/core_pattern

'produce_core' is simply : main() { *(int *)0 = 1;}

  lpq84:~# ./produce_core
  Segmentation fault (core dumped)
  lpq84:~# dmesg | tail -1
  [  614.352947] Core dump to |/foobar12345 lpq84 lpq84 lpq84 lpq84 lpq84 lpq84 lpq84 lpq84 lpq84 lpq84 lpq84 lpq84 lpq84 lpq84 lpq84 lpq84 lpq84 lpq84 lpq84 (null) pipe failed

Notice the last argument was replaced by a NULL (we were lucky enough to
not crash, but do not try this on your production machine !)

After fix :

  lpq83:~# echo "|/foobar12345 %h %h %h %h %h %h %h %h %h %h %h %h %h %h %h %h %h %h %h %h" >/proc/sys/kernel/core_pattern
  lpq83:~# ./produce_core
  Segmentation fault
  lpq83:~# dmesg | tail -1
  [  740.800441] Core dump to |/foobar12345 lpq83 lpq83 lpq83 lpq83 lpq83 lpq83 lpq83 lpq83 lpq83 lpq83 lpq83 lpq83 lpq83 lpq83 lpq83 lpq83 lpq83 lpq83 lpq83 lpq83 pipe failed

Fixes: 5fe9d8ca21cc ("coredump: cn_vprintf() has no reason to call vsnprintf() twice")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Diagnosed-by: Hugh Dickins <hughd@google.com>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

pata_at91: fix ata_host_activate() failure handling

commit 27aa64b9d1bd0d23fd692c91763a48309b694311 upstream.

Add missing clk_put() call to ata_host_activate() failure path.

Sergei says,

  "Hm, I have once fixed that (see that *if* (!ret)) but looks like a
   later commit 477c87e90853d136b188c50c0e4a93d01cad872e (ARM:
   at91/pata: use gpio_is_valid to check the gpio) broke it again. :-(
   Would be good if the changelog did mention that..."

Cc: Andrew Victor <linux@maxim.org.za>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

kernfs: add back missing error check in kernfs_fop_mmap()

commit b44b2140265ddfde03acbe809336111d31adb0d1 upstream.

While updating how mmap enabled kernfs files are handled by lockdep,
9b2db6e18945 ("sysfs: bail early from kernfs_file_mmap() to avoid
spurious lockdep warning") inadvertently dropped error return check
from kernfs_file_mmap(). The intention was just dropping "if
(ops->mmap)" check as the control won't reach the point if the mmap
callback isn't implemented, but I mistakenly removed the error return
check together with it.

This led to Xorg crash on i810 which was reported and bisected to the
commit and then to the specific change by Tobias.

Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-and-bisected-by: Tobias Powalowski <tobias.powalowski@googlemail.com>
Tested-by: Tobias Powalowski <tobias.powalowski@googlemail.com>
References: http://lkml.kernel.org/g/533D01BD.1010200@googlemail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

clocksource: Exynos_mct: Register clock event after request_irq()

commit 8db6e5104b77de5d0b7002b95069da0992a34be9 upstream.

After hotplugging CPU1 the first call of interrupt handler for CPU1
oneshot timer was called on CPU0 because it fired before setting IRQ
affinity. Affected are SoCs where Multi Core Timer interrupts are
shared (SPI), e.g. Exynos 4210.

During setup of the MCT timers the clock event device should be
registered after setting the affinity for interrupt. This will prevent
starting the timer too early.

Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Tomasz Figa <t.figa@samsung.com>,
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>,
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: linux-arm-kernel@lists.infradead.org,
Link: http://lkml.kernel.org/r/20140416143316.299247848@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

clocksource: Exynos_mct: Use irq_force_affinity() in cpu bringup

commit 30ccf03b4a6a2102a2219058bdc6d779dc637dd7 upstream.

The starting cpu is not yet in the online mask so irq_set_affinity()
fails which results in per cpu timers for this cpu ending up on some
other online cpu, ususally cpu 0.

Use irq_force_affinity() which disables the online mask check and
makes things work.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Tomasz Figa <t.figa@samsung.com>,
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>,
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: linux-arm-kernel@lists.infradead.org,
Link: http://lkml.kernel.org/r/20140416143316.106665251@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

genirq: Allow forcing cpu affinity of interrupts

commit 01f8fa4f01d8362358eb90e412bd7ae18a3ec1ad upstream.

The current implementation of irq_set_affinity() refuses rightfully to
route an interrupt to an offline cpu.

But there is a special case, where this is actually desired. Some of
the ARM SoCs have per cpu timers which require setting the affinity
during cpu startup where the cpu is not yet in the online mask.

If we can't do that, then the local timer interrupt for the about to
become online cpu is routed to some random online cpu.

The developers of the affected machines tried to work around that
issue, but that results in a massive mess in that timer code.

We have a yet unused argument in the set_affinity callbacks of the irq
chips, which I added back then for a similar reason. It was never
required so it got not used. But I'm happy that I never removed it.

That allows us to implement a sane handling of the above scenario. So
the affected SoC drivers can add the required force handling to their
interrupt chip, switch the timer code to irq_force_affinity() and
things just work.

This does not affect any existing user of irq_set_affinity().

Tagged for stable to allow a simple fix of the affected SoC clock
event drivers.

Reported-and-tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Tomasz Figa <t.figa@samsung.com>,
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>,
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: linux-arm-kernel@lists.infradead.org,
Link: http://lkml.kernel.org/r/20140416143315.717251504@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

irqchip: Gic: Support forced affinity setting

commit ffde1de64012c406dfdda8690918248b472f24e4 upstream.

To support the affinity setting of per cpu timers in the early startup
of a not yet online cpu, implement the force logic, which disables the
cpu online check.

Tagged for stable to allow a simple fix of the affected SoC clock
event drivers.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Tomasz Figa <t.figa@samsung.com>,
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>,
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: linux-arm-kernel@lists.infradead.org,
Link: http://lkml.kernel.org/r/20140416143315.916984416@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

of/irq: do irq resolution in platform_get_irq

commit 9ec36cafe43bf835f8f29273597a5b0cbc8267ef upstream.

Currently we get the following kind of errors if we try to use interrupt
phandles to irqchips that have not yet initialized:

irq: no irq domain found for /ocp/pinmux@48002030 !
------------[ cut here ]------------
WARNING: CPU: 0 PID: 1 at drivers/of/platform.c:171 of_device_alloc+0x144/0x184()
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.12.0-00038-g42a9708 #1012
(show_stack+0x14/0x1c)
(dump_stack+0x6c/0xa0)
(warn_slowpath_common+0x64/0x84)
(warn_slowpath_null+0x1c/0x24)
(of_device_alloc+0x144/0x184)
(of_platform_device_create_pdata+0x44/0x9c)
(of_platform_bus_create+0xd0/0x170)
(of_platform_bus_create+0x12c/0x170)
(of_platform_populate+0x60/0x98)

This is because we're wrongly trying to populate resources that are not
yet available. It's perfectly valid to create irqchips dynamically, so
let's fix up the issue by resolving the interrupt resources when
platform_get_irq is called.

And then we also need to accept the fact that some irqdomains do not
exist that early on, and only get initialized later on. So we can
make the current WARN_ON into just into a pr_debug().

We still attempt to populate irq resources when we create the devices.
This allows current drivers which don't use platform_get_irq to continue
to function. Once all drivers are fixed, this code can be removed.

Suggested-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ftrace/module: Hardcode ftrace_module_init() call into load_module()

commit a949ae560a511fe4e3adf48fa44fefded93e5c2b upstream.

A race exists between module loading and enabling of function tracer.

CPU 1 CPU 2
----- -----
  load_module()
   module->state = MODULE_STATE_COMING

register_ftrace_function()
mutex_lock(&ftrace_lock);
ftrace_startup()
  update_ftrace_function();
   ftrace_arch_code_modify_prepare()
    set_all_module_text_rw();
   <enables-ftrace>
    ftrace_arch_code_modify_post_process()
     set_all_module_text_ro();

[ here all module text is set to RO,
  including the module that is
  loading!! ]

   blocking_notifier_call_chain(MODULE_STATE_COMING);
    ftrace_init_module()

     [ tries to modify code, but it's RO, and fails!
       ftrace_bug() is called]

When this race happens, ftrace_bug() will produces a nasty warning and
all of the function tracing features will be disabled until reboot.

The simple solution is to treate module load the same way the core
kernel is treated at boot. To hardcode the ftrace function modification
of converting calls to mcount into nops. This is done in init/main.c
there's no reason it could not be done in load_module(). This gives
a better control of the changes and doesn't tie the state of the
module to its notifiers as much. Ftrace is special, it needs to be
treated as such.

The reason this would work, is that the ftrace_module_init() would be
called while the module is in MODULE_STATE_UNFORMED, which is ignored
by the set_all_module_text_ro() call.

Link: http://lkml.kernel.org/r/1395637826-3312-1-git-send-email-indou.takao@jp.fujitsu.com
Reported-by: Takao Indoh <indou.takao@jp.fujitsu.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rtmutex: Fix deadlock detector for real

commit 397335f004f41e5fcf7a795e94eb3ab83411a17c upstream.

The current deadlock detection logic does not work reliably due to the
following early exit path:

/*
* Drop out, when the task has no waiters. Note,
* top_waiter can be NULL, when we are in the deboosting
* mode!
*/
if (top_waiter && (!task_has_pi_waiters(task) ||
top_waiter != task_top_pi_waiter(task)))
goto out_unlock_pi;

So this not only exits when the task has no waiters, it also exits
unconditionally when the current waiter is not the top priority waiter
of the task.

So in a nested locking scenario, it might abort the lock chain walk
and therefor miss a potential deadlock.

Simple fix: Continue the chain walk, when deadlock detection is
enabled.

We also avoid the whole enqueue, if we detect the deadlock right away
(A-A). It's an optimization, but also prevents that another waiter who
comes in after the detection and before the task has undone the damage
observes the situation and detects the deadlock and returns
-EDEADLOCK, which is wrong as the other task is not in a deadlock
situation.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Reviewed-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Lai Jiangshan <laijs@cn.fujitsu.com>
Link: http://lkml.kernel.org/r/20140522031949.725272460@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mips: dts: Fix missing device_type="memory" property in memory nodes

commit dfc44f8030653b345fc6fb337558c3a07536823f upstream.

A few platforms lack a 'device_type = "memory"' for their memory
nodes, relying on an old ppc quirk in order to discover its memory.
Add the missing data so that all parsing code can find memory nodes
correctly.

Signed-off-by: Leif Lindholm <leif.lindholm@linaro.org>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: Mark Rutland <mark.rutland@arm.com>
Acked-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

MIPS/loongson2_cpufreq: Fix CPU clock rate setting

commit 8e8acb32960f42c81b1d50deac56a2c07bb6a18a upstream.

Loongson2 has been using (incorrectly) kHz for cpu_clk rate. This has
been unnoticed, as loongson2_cpufreq was the only place where the rate
was set/get. After commit 652ed95d5fa6074b3c4ea245deb0691f1acb6656
(cpufreq: introduce cpufreq_generic_get() routine) things however broke,
and now loops_per_jiffy adjustments are incorrect (1000 times too long).
The patch fixes this by changing cpu_clk rate to Hz.

Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: cpufreq@vger.kernel.org
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Patchwork: https://patchwork.linux-mips.org/patch/6678/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

futex: Prevent attaching to kernel threads

commit f0d71b3dcb8332f7971b5f2363632573e6d9486a upstream.

We happily allow userspace to declare a random kernel thread to be the
owner of a user space PI futex.

Found while analysing the fallout of Dave Jones syscall fuzzer.

We also should validate the thread group for private futexes and find
some fast way to validate whether the "alleged" owner has RW access on
the file which backs the SHM, but that's a separate issue.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Dave Jones <davej@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Darren Hart <darren@dvhart.com>
Cc: Davidlohr Bueso <davidlohr@hp.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Clark Williams <williams@redhat.com>
Cc: Paul McKenney <paulmck@linux.vnet.ibm.com>
Cc: Lai Jiangshan <laijs@cn.fujitsu.com>
Cc: Roland McGrath <roland@hack.frob.com>
Cc: Carlos ODonell <carlos@redhat.com>
Cc: Jakub Jelinek <jakub@redhat.com>
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: http://lkml.kernel.org/r/20140512201701.194824402@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

futex: Add another early deadlock detection check

commit 866293ee54227584ffcb4a42f69c1f365974ba7f upstream.

Dave Jones trinity syscall fuzzer exposed an issue in the deadlock
detection code of rtmutex:
  http://lkml.kernel.org/r/20140429151655.GA14277@redhat.com

That underlying issue has been fixed with a patch to the rtmutex code,
but the futex code must not call into rtmutex in that case because
    - it can detect that issue early
    - it avoids a different and more complex fixup for backing out

If the user space variable got manipulated to 0x80000000 which means
no lock holder, but the waiters bit set and an active pi_state in the
kernel is found we can figure out the recursive locking issue by
looking at the pi_state owner. If that is the current task, then we
can safely return -EDEADLK.

The check should have been added in commit 59fa62451 (futex: Handle
futex_pi OWNER_DIED take over correctly) already, but I did not see
the above issue caused by user space manipulation back then.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Dave Jones <davej@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Darren Hart <darren@dvhart.com>
Cc: Davidlohr Bueso <davidlohr@hp.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Clark Williams <williams@redhat.com>
Cc: Paul McKenney <paulmck@linux.vnet.ibm.com>
Cc: Lai Jiangshan <laijs@cn.fujitsu.com>
Cc: Roland McGrath <roland@hack.frob.com>
Cc: Carlos ODonell <carlos@redhat.com>
Cc: Jakub Jelinek <jakub@redhat.com>
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: http://lkml.kernel.org/r/20140512201701.097349971@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Linux 3.14.5

net-gro: reset skb->truesize in napi_reuse_skb()

[ Upstream commit e33d0ba8047b049c9262fdb1fcafb93cb52ceceb ]

Recycling skb always had been very tough...

This time it appears GRO layer can accumulate skb->truesize
adjustments made by drivers when they attach a fragment to skb.

skb_gro_receive() can only subtract from skb->truesize the used part
of a fragment.

I spotted this problem seeing TcpExtPruneCalled and
TcpExtTCPRcvCollapsed that were unexpected with a recent kernel, where
TCP receive window should be sized properly to accept traffic coming
from a driver not overshooting skb->truesize.

Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ipv4: initialise the itag variable in __mkroute_input

[ Upstream commit fbdc0ad095c0a299e9abf5d8ac8f58374951149a ]

the value of itag is a random value from stack, and may not be initiated by
fib_validate_source, which called fib_combine_itag if CONFIG_IP_ROUTE_CLASSID
is not set

This will make the cached dst uncertainty

Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ipv6: gro: fix CHECKSUM_COMPLETE support

[ Upstream commit 4de462ab63e23953fd05da511aeb460ae10cc726 ]

When GRE support was added in linux-3.14, CHECKSUM_COMPLETE handling
broke on GRE+IPv6 because we did not update/use the appropriate csum :

GRO layer is supposed to use/update NAPI_GRO_CB(skb)->csum instead of
skb->csum

Tested using a GRE tunnel and IPv6 traffic. GRO aggregation now happens
at the first level (ethernet device) instead of being done in gre
tunnel. Native IPv6+TCP is still properly aggregated.

Fixes: bf5a755f5e918 ("net-gre-gro: Add GRE support to the GRO stack")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jerry Chu <hkchu@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net_sched: fix an oops in tcindex filter

[ Upstream commit bf63ac73b3e132e6bf0c8798aba7b277c3316e19 ]

Kelly reported the following crash:

        IP: [<ffffffff817a993d>] tcf_action_exec+0x46/0x90
        PGD 3009067 PUD 300c067 PMD 11ff30067 PTE 800000011634b060
        Oops: 0000 [#1] SMP DEBUG_PAGEALLOC
        CPU: 1 PID: 639 Comm: dhclient Not tainted 3.15.0-rc4+ #342
        Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
        task: ffff8801169ecd00 ti: ffff8800d21b8000 task.ti: ffff8800d21b8000
        RIP: 0010:[<ffffffff817a993d>]  [<ffffffff817a993d>] tcf_action_exec+0x46/0x90
        RSP: 0018:ffff8800d21b9b90  EFLAGS: 00010283
        RAX: 00000000ffffffff RBX: ffff88011634b8e8 RCX: ffff8800cf7133d8
        RDX: ffff88011634b900 RSI: ffff8800cf7133e0 RDI: ffff8800d210f840
        RBP: ffff8800d21b9bb0 R08: ffffffff8287bf60 R09: 0000000000000001
        R10: ffff8800d2b22b24 R11: 0000000000000001 R12: ffff8800d210f840
        R13: ffff8800d21b9c50 R14: ffff8800cf7133e0 R15: ffff8800cad433d8
        FS:  00007f49723e1840(0000) GS:ffff88011a800000(0000) knlGS:0000000000000000
        CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
        CR2: ffff88011634b8f0 CR3: 00000000ce469000 CR4: 00000000000006e0
        Stack:
         ffff8800d2170188 ffff8800d210f840 ffff8800d2171b90 0000000000000000
         ffff8800d21b9be8 ffffffff817c55bb ffff8800d21b9c50 ffff8800d2171b90
         ffff8800d210f840 ffff8800d21b0300 ffff8800d21b9c50 ffff8800d21b9c18
        Call Trace:
         [<ffffffff817c55bb>] tcindex_classify+0x88/0x9b
         [<ffffffff817a7f7d>] tc_classify_compat+0x3e/0x7b
         [<ffffffff817a7fdf>] tc_classify+0x25/0x9f
         [<ffffffff817b0e68>] htb_enqueue+0x55/0x27a
         [<ffffffff817b6c2e>] dsmark_enqueue+0x165/0x1a4
         [<ffffffff81775642>] __dev_queue_xmit+0x35e/0x536
         [<ffffffff8177582a>] dev_queue_xmit+0x10/0x12
         [<ffffffff818f8ecd>] packet_sendmsg+0xb26/0xb9a
         [<ffffffff810b1507>] ? __lock_acquire+0x3ae/0xdf3
         [<ffffffff8175cf08>] __sock_sendmsg_nosec+0x25/0x27
         [<ffffffff8175d916>] sock_aio_write+0xd0/0xe7
         [<ffffffff8117d6b8>] do_sync_write+0x59/0x78
         [<ffffffff8117d84d>] vfs_write+0xb5/0x10a
         [<ffffffff8117d96a>] SyS_write+0x49/0x7f
         [<ffffffff8198e212>] system_call_fastpath+0x16/0x1b

This is because we memcpy struct tcindex_filter_result which contains
struct tcf_exts, obviously struct list_head can not be simply copied.
This is a regression introduced by commit 33be627159913b094bb578
(net_sched: act: use standard struct list_head).

It's not very easy to fix it as the code is a mess:

       if (old_r)
               memcpy(&cr, r, sizeof(cr));
       else {
               memset(&cr, 0, sizeof(cr));
               tcf_exts_init(&cr.exts, TCA_TCINDEX_ACT, TCA_TCINDEX_POLICE);
       }
       ...
       tcf_exts_change(tp, &cr.exts, &e);
       ...
       memcpy(r, &cr, sizeof(cr));

the above code should equal to:

        tcindex_filter_result_init(&cr);
        if (old_r)
               cr.res = r->res;
        ...
        if (old_r)
               tcf_exts_change(tp, &r->exts, &e);
        else
               tcf_exts_change(tp, &cr.exts, &e);
        ...
        r->res = cr.res;

after this change, since there is no need to copy struct tcf_exts.

And it also fixes other places zero'ing struct's contains struct tcf_exts.

Fixes: commit 33be627159913b0 (net_sched: act: use standard struct list_head)
Reported-by: Kelly Anderson <kelly@xilka.com>
Tested-by: Kelly Anderson <kelly@xilka.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ip_tunnel: Initialize the fallback device properly

[ Upstream commit 78ff4be45a4c51d8fb21ad92e4fabb467c6c3eeb ]

We need to initialize the fallback device to have a correct mtu
set on this device. Otherwise the mtu is set to null and the device
is unusable.

Fixes: fd58156e456d ("IPIP: Use ip-tunneling code.")
Cc: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

batman-adv: fix local TT check for outgoing arp requests in DAT

[ Upstream commit cc2f33860cea0e48ebec096130bd0f7c4bf6e0bc ]

Change introduced by 88e48d7b3340ef07b108eb8a8b3813dd093cc7f7
("batman-adv: make DAT drop ARP requests targeting local clients")
implements a check that prevents DAT from using the caching
mechanism when the client that is supposed to provide a reply
to an arp request is local.

However change brought by be1db4f6615b5e6156c807ea8985171c215c2d57
("batman-adv: make the Distributed ARP Table vlan aware")
has not converted the above check into its vlan aware version
thus making it useless when the local client is behind a vlan.

Fix the behaviour by properly specifying the vlan when
checking for a client being local or not.

Reported-by: Simon Wunderlich <simon@open-mesh.com>
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

batman-adv: increase orig refcount when storing ref in gw_node

[ Upstream commit 377fe0f968b30a1a714fab53a908061914f30e26 ]

A pointer to the orig_node representing a bat-gateway is
stored in the gw_node->orig_node member, but the refcount
for such orig_node is never increased.
This leads to memory faults when gw_node->orig_node is accessed
and the originator has already been freed.

Fix this by increasing the refcount on gw_node creation
and decreasing it on gw_node free.

Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

batman-adv: fix reference counting imbalance while sending fragment

[ Upstream commit be181015a189cd141398b761ba4e79d33fe69949 ]

In the new fragmentation code the batadv_frag_send_packet()
function obtains a reference to the primary_if, but it does
not release it upon return.

This reference imbalance prevents the primary_if (and then
the related netdevice) to be properly released on shut down.

Fix this by releasing the primary_if in batadv_frag_send_packet().

Introduced by ee75ed88879af88558818a5c6609d85f60ff0df4
("batman-adv: Fragment and send skbs larger than mtu")

Cc: Martin Hundebøll <martin@hundeboll.net>
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Acked-by: Martin Hundebøll <martin@hundeboll.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

batman-adv: fix indirect hard_iface NULL dereference

[ Upstream commit 16a4142363b11952d3aa76ac78004502c0c2fe6e ]

If hard_iface is NULL and goto out is made batadv_hardif_free_ref()
doesn't check for NULL before dereferencing it to get to refcount.

Introduced in cb1c92ec37fb70543d133a1fa7d9b54d6f8a1ecd
("batman-adv: add debugfs support to view multiif tables").

Reported-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Acked-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: gro: make sure skb->cb[] initial content has not to be zero

[ Upstream commit 29e98242783ed3ba569797846a606ba66f781625 ]

Starting from linux-3.13, GRO attempts to build full size skbs.

Problem is the commit assumed one particular field in skb->cb[]
was clean, but it is not the case on some stacked devices.

Timo reported a crash in case traffic is decrypted before
reaching a GRE device.

Fix this by initializing NAPI_GRO_CB(skb)->last at the right place,
this also removes one conditional.

Thanks a lot to Timo for providing full reports and bisecting this.

Fixes: 8a29111c7ca6 ("net: gro: allow to build full sized skb")
Bisected-by: Timo Teras <timo.teras@iki.fi>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Tested-by: Timo Teräs <timo.teras@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

bonding: fix out of range parameters for bond_intmax_tbl

[ Upstream commit 81c708068dfedece038e07d818ba68333d8d885d ]

I've missed to add a NULL entry to the bond_intmax_tbl when I introduced
it with the conversion of arp_interval so add it now.

CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Fixes: 7bdb04ed0dbf ("bonding: convert arp_interval to use the new option API")
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Acked-by: Veaceslav Falico <vfalico@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: phy: Don't call phy_resume if phy_init_hw failed

[ Upstream commit b394745df2d9d4c30bf1bcc55773bec6f3bc7c67 ]

After the call to phy_init_hw failed in phy_attach_direct, phy_detach is called
to detach the phy device from its network device. If the attached driver is a
generic phy driver, this also detaches the driver. Subsequently phy_resume
is called, which assumes without checking that a driver is attached to the
device. This will result in a crash such as

Unable to handle kernel paging request for data at address 0xffffffffffffff90
Faulting instruction address: 0xc0000000003a0e18
Oops: Kernel access of bad area, sig: 11 [#1]
...
NIP [c0000000003a0e18] .phy_attach_direct+0x68/0x17c
LR [c0000000003a0e6c] .phy_attach_direct+0xbc/0x17c
Call Trace:
[c0000003fc0475d0] [c0000000003a0e6c] .phy_attach_direct+0xbc/0x17c (unreliable)
[c0000003fc047670] [c0000000003a0ff8] .phy_connect_direct+0x28/0x98
[c0000003fc047700] [c0000000003f0074] .of_phy_connect+0x4c/0xa4

Only call phy_resume if phy_init_hw was successful.

Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rtnetlink: wait for unregistering devices in rtnl_link_unregister()

[ Upstream commit 200b916f3575bdf11609cb447661b8d5957b0bbf ]

From: Cong Wang <cwang@twopensource.com>

commit 50624c934db18ab90 (net: Delay default_device_exit_batch until no
devices are unregistering) introduced rtnl_lock_unregistering() for
default_device_exit_batch(). Same race could happen we when rmmod a driver
which calls rtnl_link_unregister() as we call dev->destructor without rtnl
lock.

For long term, I think we should clean up the mess of netdev_run_todo()
and net namespce exit code.

Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ipv6: fix calculation of option len in ip6_append_data

[ Upstream commit 3a1cebe7e05027a1c96f2fc1a8eddf5f19b78f42 ]

tot_len does specify the size of struct ipv6_txoptions. We need opt_flen +
opt_nflen to calculate the overall length of additional ipv6 extensions.

I found this while auditing the ipv6 output path for a memory corruption
reported by Alexey Preobrazhensky while he fuzzed an instrumented
AddressSanitizer kernel with trinity. This may or may not be the cause
of the original bug.

Fixes: 4df98e76cde7c6 ("ipv6: pmtudisc setting not respected with UFO/CORK")
Reported-by: Alexey Preobrazhensky <preobr@google.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: avoid dependency of net_get_random_once on nop patching

[ Upstream commit 3d4405226d27b3a215e4d03cfa51f536244e5de7 ]

net_get_random_once depends on the static keys infrastructure to patch up
the branch to the slow path during boot. This was realized by abusing the
static keys api and defining a new initializer to not enable the call
site while still indicating that the branch point should get patched
up. This was needed to have the fast path considered likely by gcc.

The static key initialization during boot up normally walks through all
the registered keys and either patches in ideal nops or enables the jump
site but omitted that step on x86 if ideal nops where already placed at
static_key branch points. Thus net_get_random_once branches not always
became active.

This patch switches net_get_random_once to the ordinary static_key
api and thus places the kernel fast path in the - by gcc considered -
unlikely path. Microbenchmarks on Intel and AMD x86-64 showed that
the unlikely path actually beats the likely path in terms of cycle cost
and that different nop patterns did not make much difference, thus this
switch should not be noticeable.

Fixes: a48e42920ff38b ("net: introduce new macro net_get_random_once")
Reported-by: Tuomas Räsänen <tuomasjjrasanen@tjjr.fi>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: filter: s390: fix JIT address randomization

[ Upstream commit e84d2f8d2ae33c8215429824e1ecf24cbca9645e ]

This is the s390 variant of Alexei's JIT bug fix.
(patch description below stolen from Alexei's patch)

bpf_alloc_binary() adds 128 bytes of room to JITed program image
and rounds it up to the nearest page size. If image size is close
to page size (like 4000), it is rounded to two pages:
round_up(4000 + 4 + 128) == 8192
then 'hole' is computed as 8192 - (4000 + 4) = 4188
If prandom_u32() % hole selects a number >= PAGE_SIZE - sizeof(*header)
then kernel will crash during bpf_jit_free():

kernel BUG at arch/x86/mm/pageattr.c:887!
Call Trace:
[<ffffffff81037285>] change_page_attr_set_clr+0x135/0x460
[<ffffffff81694cc0>] ? _raw_spin_unlock_irq+0x30/0x50
[<ffffffff810378ff>] set_memory_rw+0x2f/0x40
[<ffffffffa01a0d8d>] bpf_jit_free_deferred+0x2d/0x60
[<ffffffff8106bf98>] process_one_work+0x1d8/0x6a0
[<ffffffff8106bf38>] ? process_one_work+0x178/0x6a0
[<ffffffff8106c90c>] worker_thread+0x11c/0x370

since bpf_jit_free() does:
  unsigned long addr = (unsigned long)fp->bpf_func & PAGE_MASK;
  struct bpf_binary_header *header = (void *)addr;
to compute start address of 'bpf_binary_header'
and header->pages will pass junk to:
  set_memory_rw(addr, header->pages);

Fix it by making sure that &header->image[prandom_u32() % hole] and &header
are in the same page.

Fixes: aa2d2c73c21f2 ("s390/bpf,jit: address randomize and write protect jit code")

Reported-by: Alexei Starovoitov <ast@plumgrid.com>
Cc: <stable@vger.kernel.org> # v3.11+
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: filter: x86: fix JIT address randomization

[ Upstream commit 773cd38f40b8834be991dbfed36683acc1dd41ee ]

bpf_alloc_binary() adds 128 bytes of room to JITed program image
and rounds it up to the nearest page size. If image size is close
to page size (like 4000), it is rounded to two pages:
round_up(4000 + 4 + 128) == 8192
then 'hole' is computed as 8192 - (4000 + 4) = 4188
If prandom_u32() % hole selects a number >= PAGE_SIZE - sizeof(*header)
then kernel will crash during bpf_jit_free():

kernel BUG at arch/x86/mm/pageattr.c:887!
Call Trace:
[<ffffffff81037285>] change_page_attr_set_clr+0x135/0x460
[<ffffffff81694cc0>] ? _raw_spin_unlock_irq+0x30/0x50
[<ffffffff810378ff>] set_memory_rw+0x2f/0x40
[<ffffffffa01a0d8d>] bpf_jit_free_deferred+0x2d/0x60
[<ffffffff8106bf98>] process_one_work+0x1d8/0x6a0
[<ffffffff8106bf38>] ? process_one_work+0x178/0x6a0
[<ffffffff8106c90c>] worker_thread+0x11c/0x370

since bpf_jit_free() does:
  unsigned long addr = (unsigned long)fp->bpf_func & PAGE_MASK;
  struct bpf_binary_header *header = (void *)addr;
to compute start address of 'bpf_binary_header'
and header->pages will pass junk to:
  set_memory_rw(addr, header->pages);

Fix it by making sure that &header->image[prandom_u32() % hole] and &header
are in the same page

Fixes: 314beb9bcabfd ("x86: bpf_jit_comp: secure bpf jit against spraying attacks")
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

batman-adv: fix removing neigh_ifinfo

[ Upstream commit 709de13f0c532fe9c468c094aff069a725ed57fe ]

When an interface is removed separately, all neighbors need to be
checked if they have a neigh_ifinfo structure for that particular
interface. If that is the case, remove that ifinfo so any references to
a hard interface can be freed.

This is a regression introduced by
89652331c00f43574515059ecbf262d26d885717
("batman-adv: split tq information in neigh_node struct")

Reported-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Simon Wunderlich <simon@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

batman-adv: always run purge_orig_neighbors

[ Upstream commit 7b955a9fc164487d7c51acb9787f6d1b01b35ef6 ]

The current code will not execute batadv_purge_orig_neighbors() when an
orig_ifinfo has already been purged. However we need to run it in any
case. Fix that.

This is a regression introduced by
7351a4822d42827ba0110677c0cbad88a3d52585
("batman-adv: split out router from orig_node")

Signed-off-by: Simon Wunderlich <simon@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

batman-adv: fix neigh reference imbalance

[ Upstream commit 000c8dff97311357535d64539e58990526e4de70 ]

When an interface is removed from batman-adv, the orig_ifinfo of a
orig_node may be removed without releasing the router first.
This will prevent the reference for the neighbor pointed at by the
orig_ifinfo->router to be released, and this leak may result in
reference leaks for the interface used by this neighbor. Fix that.

This is a regression introduced by
7351a4822d42827ba0110677c0cbad88a3d52585
("batman-adv: split out router from orig_node").

Reported-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Simon Wunderlich <simon@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

batman-adv: fix neigh_ifinfo imbalance

[ Upstream commit c1e517fbbcdb13f50662af4edc11c3251fe44f86 ]

The neigh_ifinfo object must be freed if it has been used in
batadv_iv_ogm_process_per_outif().

This is a regression introduced by
89652331c00f43574515059ecbf262d26d885717
("batman-adv: split tq information in neigh_node struct")

Reported-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Simon Wunderlich <simon@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

neigh: set nud_state to NUD_INCOMPLETE when probing router reachability

[ Upstream commit 2176d5d41891753774f648b67470398a5acab584 ]

Since commit 7e98056964("ipv6: router reachability probing"), a router falls
into NUD_FAILED will be probed.

Now if function rt6_select() selects a router which neighbour state is NUD_FAILED,
and at the same time function rt6_probe() changes the neighbour state to NUD_PROBE,
then function dst_neigh_output() can directly send packets, but actually the
neighbour still is unreachable. If we set nud_state to NUD_INCOMPLETE instead
NUD_PROBE, packets will not be sent out until the neihbour is reachable.

In addition, because the route should be probes with a single NS, so we must
set neigh->probes to neigh_max_probes(), then the neigh timer timeout and function
neigh_timer_handler() will not send other NS Messages.

Signed-off-by: Duan Jiong <duanj.fnst@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ip6_tunnel: fix potential NULL pointer dereference

[ Upstream commit c8965932a2e3b70197ec02c6741c29460279e2a8 ]

The function ip6_tnl_validate assumes that the rtnl
attribute IFLA_IPTUN_PROTO always be filled . If this
attribute is not filled by the userspace application
kernel get crashed with NULL pointer dereference. This
patch fixes the potential kernel crash when
IFLA_IPTUN_PROTO is missing .

Signed-off-by: Susant Sahani <susant@redhat.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

sfc: fix calling of free_irq with already free vector

[ Upstream commit 1c3639005f48492e5f2d965779efd814e80f8b15 ]

If the sfc driver is in legacy interrupt mode (either explicitly by
using interrupt_mode module param or by falling back to it) it will
hit a warning at kernel/irq/manage.c because it will try to free an irq
which wasn't allocated by it in the first place because the MSI(X) irqs are
zero and it'll try to free them unconditionally. So fix it by checking if
we're in legacy mode and freeing the appropriate irqs.

CC: Zenghui Shi <zshi@redhat.com>
CC: Ben Hutchings <ben@decadent.org.uk>
CC: <linux-net-drivers@solarflare.com>
CC: Shradha Shah <sshah@solarflare.com>
CC: David S. Miller <davem@davemloft.net>
Fixes: 1899c111a535 ("sfc: Fix IRQ cleanup in case of a probe failure")
Reported-by: Zenghui Shi <zshi@redhat.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Acked-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

macvlan: Don't propagate IFF_ALLMULTI changes on down interfaces.

[ Upstream commit bbeb0eadcf9fe74fb2b9b1a6fea82cd538b1e556 ]

Clearing the IFF_ALLMULTI flag on a down interface could cause an allmulti
overflow on the underlying interface.

Attempting the set IFF_ALLMULTI on the underlying interface would cause an
error and the log message:

"allmulti touches root, set allmulti failed."

Signed-off-by: Peter Christensen <pch@ordbogen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: cdc_mbim: handle unaccelerated VLAN tagged frames

[ Upstream commit 6b5eeb7f874b689403e52a646e485d0191ab9507 ]

This driver maps 802.1q VLANs to MBIM sessions. The mapping is based on
a bogus assumption that all tagged frames will use the acceleration API
because we enable NETIF_F_HW_VLAN_CTAG_TX. This fails for e.g. frames
tagged in userspace using packet sockets. Such frames will erroneously
be considered as untagged and silently dropped based on not being IP.

Fix by falling back to looking into the ethernet header for a tag if no
accelerated tag was found.

Fixes: a82c7ce5bc5b ("net: cdc_ncm: map MBIM IPS SessionID to VLAN ID")
Cc: Greg Suarez <gsuarez@smithmicro.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ipv4: fib_semantics: increment fib_info_cnt after fib_info allocation

[ Upstream commit aeefa1ecfc799b0ea2c4979617f14cecd5cccbfd ]

Increment fib_info_cnt in fib_create_info() right after successfuly
alllocating fib_info structure, overwise fib_metrics allocation failure
leads to fib_info_cnt incorrectly decremented in free_fib_info(), called
on error path from fib_create_info().

Signed-off-by: Sergey Popovich <popovich_sergei@mail.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: ipv6: send pkttoobig immediately if orig frag size > mtu

[ Upstream commit 418a31561d594a2b636c1e2fa94ecd9e1245abb1 ]

If conntrack defragments incoming ipv6 frags it stores largest original
frag size in ip6cb and sets ->local_df.

We must thus first test the largest original frag size vs. mtu, and not
vice versa.

Without this patch PKTTOOBIG is still generated in ip6_fragment() later
in the stack, but

1) IPSTATS_MIB_INTOOBIGERRORS won't increment
2) packet did (needlessly) traverse netfilter postrouting hook.

Fixes: fe6cc55f3a9 ("net: ip, ipv6: handle gso skbs in forwarding path")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: ipv4: ip_forward: fix inverted local_df test

[ Upstream commit ca6c5d4ad216d5942ae544bbf02503041bd802aa ]

local_df means 'ignore DF bit if set', so if its set we're
allowed to perform ip fragmentation.

This wasn't noticed earlier because the output path also drops such skbs
(and emits needed icmp error) and because netfilter ip defrag did not
set local_df until couple of days ago.

Only difference is that DF-packets-larger-than MTU now discarded
earlier (f.e. we avoid pointless netfilter postrouting trip).

While at it, drop the repeated test ip_exceeds_mtu, checking it once
is enough...

Fixes: fe6cc55f3a9 ("net: ip, ipv6: handle gso skbs in forwarding path")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: cdc_mbim: __vlan_find_dev_deep need rcu_read_lock

[ Upstream commit 4f4178f3bb1f470d7fb863ec531e08e20a0fd51c ]

Fixes this warning introduced by commit 5b8f15f78e6f
("net: cdc_mbim: handle IPv6 Neigbor Solicitations"):

===============================
[ INFO: suspicious RCU usage. ]
3.15.0-rc3 #213 Tainted: G W O
-------------------------------
net/8021q/vlan_core.c:69 suspicious rcu_dereference_check() usage!

other info that might help us debug this:

rcu_scheduler_active = 1, debug_locks = 1
no locks held by ksoftirqd/0/3.

stack backtrace:
CPU: 0 PID: 3 Comm: ksoftirqd/0 Tainted: G W O 3.15.0-rc3 #213
Hardware name: LENOVO 2776LEG/2776LEG, BIOS 6EET55WW (3.15 ) 12/19/2011
0000000000000001 ffff880232533bf0 ffffffff813a5ee6 0000000000000006
ffff880232530090 ffff880232533c20 ffffffff81076b94 0000000000000081
0000000000000000 ffff8802085ac000 ffff88007fc8ea00 ffff880232533c50
Call Trace:
[<ffffffff813a5ee6>] dump_stack+0x4e/0x68
[<ffffffff81076b94>] lockdep_rcu_suspicious+0xfa/0x103
[<ffffffff813978a6>] __vlan_find_dev_deep+0x54/0x94
[<ffffffffa04a1938>] cdc_mbim_rx_fixup+0x379/0x66a [cdc_mbim]
[<ffffffff813ab76f>] ? _raw_spin_unlock_irqrestore+0x3a/0x49
[<ffffffff81079671>] ? trace_hardirqs_on_caller+0x192/0x1a1
[<ffffffffa059bd10>] usbnet_bh+0x59/0x287 [usbnet]
[<ffffffff8104067d>] tasklet_action+0xbb/0xcd
[<ffffffff81040057>] __do_softirq+0x14c/0x30d
[<ffffffff81040237>] run_ksoftirqd+0x1f/0x50
[<ffffffff8105f13e>] smpboot_thread_fn+0x172/0x18e
[<ffffffff8105efcc>] ? SyS_setgroups+0xdf/0xdf
[<ffffffff810594b0>] kthread+0xb5/0xbd
[<ffffffff813a84b1>] ? __wait_for_common+0x13b/0x170
[<ffffffff810593fb>] ? __kthread_parkme+0x5c/0x5c
[<ffffffff813b147c>] ret_from_fork+0x7c/0xb0
[<ffffffff810593fb>] ? __kthread_parkme+0x5c/0x5c

Fixes: 5b8f15f78e6f ("net: cdc_mbim: handle IPv6 Neigbor Solicitations")
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ipv4: ip_tunnels: disable cache for nbma gre tunnels

[ Upstream commit 22fb22eaebf4d16987f3fd9c3484c436ee0badf2 ]

The connected check fails to check for ip_gre nbma mode tunnels
properly. ip_gre creates temporary tnl_params with daddr specified
to pass-in the actual target on per-packet basis from neighbor
layer. Detect these tunnels by inspecting the actual tunnel
configuration.

Minimal test case:
ip route add 192.168.1.1/32 via 10.0.0.1
ip route add 192.168.1.2/32 via 10.0.0.2
ip tunnel add nbma0 mode gre key 1 tos c0
ip addr add 172.17.0.0/16 dev nbma0
ip link set nbma0 up
ip neigh add 172.17.0.1 lladdr 192.168.1.1 dev nbma0
ip neigh add 172.17.0.2 lladdr 192.168.1.2 dev nbma0
ping 172.17.0.1
ping 172.17.0.2

The second ping should be going to 192.168.1.2 and head 10.0.0.2;
but cached gre tunnel level route is used and it's actually going
to 192.168.1.1 via 10.0.0.1.

The lladdr's need to go to separate dst for the bug to trigger.
Test case uses separate route entries, but this can also happen
when the route entry is same: if there is a nexthop exception or
the GRE tunnel is IPsec'ed in which case the dst points to xfrm
bundle unique to the gre lladdr.

Fixes: 7d442fab0a67 ("ipv4: Cache dst in tunnels")
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Cc: Tom Herbert <therbert@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ip_tunnel: Set network header properly for IP_ECN_decapsulate()

[ Upstream commit e96f2e7c430014eff52c93cabef1ad4f42ed0db1 ]

In ip_tunnel_rcv(), set skb->network_header to inner IP header
before IP_ECN_decapsulate().

Without the fix, IP_ECN_decapsulate() takes outer IP header as
inner IP header, possibly causing error messages or packet drops.

Note that this skb_reset_network_header() call was in this spot when
the original feature for checking consistency of ECN bits through
tunnels was added in eccc1bb8d4b4 ("tunnel: drop packet if ECN present
with not-ECT"). It was only removed from this spot in 3d7b46cd20e3
("ip_tunnel: push generic protocol handling to ip_tunnel module.").

Fixes: 3d7b46cd20e3 ("ip_tunnel: push generic protocol handling to ip_tunnel module.")
Reported-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Ying Cai <ycai@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net/mlx4_core: Don't issue PCIe speed/width checks for VFs

[ Upstream commit 83d3459a5928f18c9344683e31bc2a7c3c25562a ]

Carrying out PCI speed/width checks through pcie_get_minimum_link()
on VFs yield wrong results, so remove them.

Fixes: b912b2f ('net/mlx4_core: Warn if device doesn't have enough PCI bandwidth')
Signed-off-by: Eyal Perry <eyalpe@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: cdc_ncm: fix buffer overflow

[ Upstream commit 9becd707841207652449a8dfd90fe9c476d88546 ]

Commit 4d619f625a60 ("net: cdc_ncm: no point in filling up the NTBs
if we send ZLPs") changed the padding logic for devices with the ZLP
flag set. This meant that frames of any size will be sent without
additional padding, except for the single byte added if the size is
a multiple of the USB packet size. But if the unpadded size is
identical to the maximum frame size, and the maximum size is a
multiplum of the USB packet size, then this one-byte padding will
overflow the buffer.

Prevent padding if already at maximum frame size, letting usbnet
transmit a ZLP instead in this case.

Fixes: 4d619f625a60 ("net: cdc_ncm: no point in filling up the NTBs if we send ZLPs")
Reported by: Yu-an Shih <yshih@nvidia.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

vsock: Make transport the proto owner

[ Upstream commit 2c4a336e0a3e203fab6aa8d8f7bb70a0ad968a6b ]

Right now the core vsock module is the owner of the proto family. This
means there's nothing preventing the transport module from unloading if
there are open sockets, which results in a panic. Fix that by allowing
the transport to be the owner, which will refcount it properly.

Includes version bump to 1.0.1.0-k

Passes checkpatch this time, I swear...

Acked-by: Dmitry Torokhov <dtor@vmware.com>
Signed-off-by: Andy King <acking@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: sched: lock imbalance in hhf qdisc

[ Upstream commit f6a082fed1e6407c2f4437d0d963b1bcbe5f9f58 ]

hhf_change() takes the sch_tree_lock and releases it but misses the
error cases. Fix the missed case here.

To reproduce try a command like this,

# tc qdisc change dev p3p2 root hhf quantum 40960 non_hh_weight 300000

Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tcp_cubic: fix the range of delayed_ack

[ Upstream commit 0cda345d1b2201dd15591b163e3c92bad5191745 ]

commit b9f47a3aaeab (tcp_cubic: limit delayed_ack ratio to prevent
divide error) try to prevent divide error, but there is still a little
chance that delayed_ack can reach zero. In case the param cnt get
negative value, then ratio+cnt would overflow and may happen to be zero.
As a result, min(ratio, ACK_RATIO_LIMIT) will calculate to be zero.

In some old kernels, such as 2.6.32, there is a bug that would
pass negative param, which then ultimately leads to this divide error.

commit 5b35e1e6e9c (tcp: fix tcp_trim_head() to adjust segment count
with skb MSS) fixed the negative param issue. However,
it's safe that we fix the range of delayed_ack as well,
to make sure we do not hit a divide by zero.

CC: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Liu Yu <allanyuliu@tencent.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Revert "macvlan : fix checksums error when we are in bridge mode"

[ Upstream commit f114890cdf84d753f6b41cd0cc44ba51d16313da ]

This reverts commit 12a2856b604476c27d85a5f9a57ae1661fc46019.
The commit above doesn't appear to be necessary any more as the
checksums appear to be correctly computed/validated.

Additionally the above commit breaks kvm configurations where
one VM is using a device that support checksum offload (virtio) and
the other VM does not.
In this case, packets leaving virtio device will have CHECKSUM_PARTIAL
set. The packets is forwarded to a macvtap that has offload features
turned off. Since we use CHECKSUM_UNNECESSARY, the host does does not
update the checksum and thus a bad checksum is passed up to
the guest.

CC: Daniel Lezcano <daniel.lezcano@free.fr>
CC: Patrick McHardy <kaber@trash.net>
CC: Andrian Nord <nightnord@gmail.com>
CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: Michael S. Tsirkin <mst@redhat.com>
CC: Jason Wang <jasowang@redhat.com>
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mactap: Fix checksum errors for non-gso packets in bridge mode

[ Upstream commit cbdb04279ccaefcc702c8757757eea8ed76e50cf ]

The following is a problematic configuration:

VM1: virtio-net device connected to macvtap0@eth0
VM2: e1000 device connect to macvtap1@eth0

The problem is is that virtio-net supports checksum offloading
and thus sends the packets to the host with CHECKSUM_PARTIAL set.
On the other hand, e1000 does not support any acceleration.

For small TCP packets (and this includes the 3-way handshake),
e1000 ends up receiving packets that only have a partial checksum
set. This causes TCP to fail checksum validation and to drop
packets. As a result tcp connections can not be established.

Commit 3e4f8b787370978733ca6cae452720a4f0c296b8
macvtap: Perform GSO on forwarding path.
fixes this issue for large packets wthat will end up undergoing GSO.
This commit adds a check for the non-GSO case and attempts to
compute the checksum for partially checksummed packets in the
non-GSO case.

CC: Daniel Lezcano <daniel.lezcano@free.fr>
CC: Patrick McHardy <kaber@trash.net>
CC: Andrian Nord <nightnord@gmail.com>
CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: Michael S. Tsirkin <mst@redhat.com>
CC: Jason Wang <jasowang@redhat.com>
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: sctp: Don't transition to PF state when transport has exhausted 'Path.Max.Retrans'.

[ Upstream commit 8c2eab9097dba50bcd73ed4632baccc3f34857f9 ]

Don't transition to the PF state on every strike after 'Path.Max.Retrans'.
Per draft-ietf-tsvwg-sctp-failover-03 Section 5.1.6:

   Additional (PMR - PFMR) consecutive timeouts on a PF destination
   confirm the path failure, upon which the destination transitions to the
   Inactive state.  As described in [RFC4960], the sender (i) SHOULD notify
   ULP about this state transition, and (ii) transmit heartbeats to the
   Inactive destination at a lower frequency as described in Section 8.3 of
   [RFC4960].

This also prevents sending SCTP_ADDR_UNREACHABLE to the user as the state
bounces between SCTP_INACTIVE and SCTP_PF for each subsequent strike.

Signed-off-by: Karl Heiss <kheiss@gmail.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

slip: fix spinlock variant

[ Upstream commit ddcde142bed44490e338ed1124cb149976d355bb ]

With commit cc9fa74e2a ("slip/slcan: added locking in wakeup function") a
formerly missing locking was added to slip.c and slcan.c by Andre Naujoks.

Alexander Stein contributed the fix 367525c8c2 ("can: slcan: Fix spinlock
variant") as the kernel lock debugging advised to use spin_lock_bh() instead
of just using spin_lock().

This fix has to be applied to the same code section in slip.c for the same
reason too.

Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: qmi_wwan: add a number of Dell devices

[ Upstream commit 6f10c5d1b1aeddb63d33070abb8bc5a177beeb1f ]

Dan writes:

"The Dell drivers use the same configuration for PIDs:

81A2: Dell Wireless 5806 Gobi(TM) 4G LTE Mobile Broadband Card
81A3: Dell Wireless 5570 HSPA+ (42Mbps) Mobile Broadband Card
81A4: Dell Wireless 5570e HSPA+ (42Mbps) Mobile Broadband Card
81A8: Dell Wireless 5808 Gobi(TM) 4G LTE Mobile Broadband Card
81A9: Dell Wireless 5808e Gobi(TM) 4G LTE Mobile Broadband Card

These devices are all clearly Sierra devices, but are also definitely
Gobi-based. The A8 might be the MC7700/7710 and A9 is likely a MC7750.

>From DellGobi5kSetup.exe from the Dell drivers:

usbif0: serial/firmware loader?
usbif2: nmea
usbif3: modem/ppp
usbif8: net/QMI"

Reported-by: AceLan Kao <acelan.kao@canonical.com>
Reported-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: qmi_wwan: add a number of CMOTech devices

[ Upstream commit 41be7d90993b1502d445bfc59e58348c258ce66a ]

A number of older CMOTech modems are based on Qualcomm
chips and exporting a QMI/wwan function.

Reported-by: Lars Melin <larsm17@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: qmi_wwan: add Alcatel L800MA

[ Upstream commit 75573660c47a0db7cc931dcf154945610e02130a ]

Device interface layout:
0: ff/ff/ff - serial
1: ff/00/00 - serial AT+PPP
2: ff/ff/ff - QMI/wwan
3: 08/06/50 - storage

Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: qmi_wwan: add Olivetti Olicard 500

[ Upstream commit efc0b25c3add97717ece57bf5319792ca98f348e ]

Device interface layout:
0: ff/ff/ff - serial
1: ff/ff/ff - serial AT+PPP
2: 08/06/50 - storage
3: ff/ff/ff - serial
4: ff/ff/ff - QMI/wwan

Reported-by: Julio Araujo <julio.araujo@wllctel.com.br>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: qmi_wwan: add Sierra Wireless MC7305/MC7355

[ Upstream commit 9214224e43e4264b02686ea8b455f310935607b5 ]

Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: qmi_wwan: add Sierra Wireless MC73xx

[ Upstream commit 1c138607a7be64074d7fba68d0d533ec38f9d17b ]

Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: qmi_wwan: add Sierra Wireless EM7355

[ Upstream commit b85f5deaf052340021d025e120a9858f084a1d79 ]

Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

sctp: reset flowi4_oif parameter on route lookup

[ Upstream commit 85350871317a5adb35519d9dc6fc9e80809d42ad ]

commit 813b3b5db83 (ipv4: Use caller's on-stack flowi as-is
in output route lookups.) introduces another regression which
is very similar to the problem of commit e6b45241c (ipv4: reset
flowi parameters on route connect) wants to fix:
Before we call ip_route_output_key() in sctp_v4_get_dst() to
get a dst that matches a bind address as the source address,
we have already called this function previously and the flowi
parameters have been initialized including flowi4_oif, so when
we call this function again, the process in __ip_route_output_key()
will be different because of the setting of flowi4_oif, and we'll
get a networking device which corresponds to the inputted flowi4_oif
as the output device, this is wrong because we'll never hit this
place if the previously returned source address of dst match one
of the bound addresses.

To reproduce this problem, a vlan setting is enough:
  # ifconfig eth0 up
  # route del default
  # vconfig add eth0 2
  # vconfig add eth0 3
  # ifconfig eth0.2 10.0.1.14 netmask 255.255.255.0
  # route add default gw 10.0.1.254 dev eth0.2
  # ifconfig eth0.3 10.0.0.14 netmask 255.255.255.0
  # ip rule add from 10.0.0.14 table 4
  # ip route add table 4 default via 10.0.0.254 src 10.0.0.14 dev eth0.3
  # sctp_darn -H 10.0.0.14 -P 36422 -h 10.1.4.134 -p 36422 -s -I
You'll detect that all the flow are routed to eth0.2(10.0.1.254).

Signed-off-by: Xufeng Zhang <xufeng.zhang@windriver.com>
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

bridge: Handle IFLA_ADDRESS correctly when creating bridge device

[ Upstream commit 30313a3d5794472c3548d7288e306a5492030370 ]

When bridge device is created with IFLA_ADDRESS, we are not calling
br_stp_change_bridge_id(), which leads to incorrect local fdb
management and bridge id calculation, and prevents us from receiving
frames on the bridge device.

Reported-by: Tom Gundersen <teg@jklm.no>
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ipv6: fib: fix fib dump restart

[ Upstream commit 1c2658545816088477e91860c3a645053719cb54 ]

When the ipv6 fib changes during a table dump, the walk is
restarted and the number of nodes dumped are skipped. But the existing
code doesn't advance to the next node after a node is skipped. This can
cause the dump to loop or produce lots of duplicates when the fib
is modified during the dump.

This change advances the walk to the next node if the current node is
skipped after a restart.

Signed-off-by: Kumar Sundararajan <kumar@fb.com>
Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>