review.tizen.org Git - platform/kernel/linux-rpi.git/log

drm/amd/display: Split out common HUBP registers and code

There are shared regs and code across DCN generations. Pull them out
into a shared common location.

Also, expose some dcn20 init functions.

Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: skip retrain in dc_link_set_preferred_link_settings() if using passive dongle

[Why]
Fixes issue when we have a display connected using a passive
dongle and then emulate over it using a DP connection at 1 x 1.62 Ghz.
System hangs because register bus returns back 0xFFFFFFFF for all
register reads after setting register DIG_BE_CNTL in
dcn10_link_encoder_connect_dig_be_to_fe(). Hang occurs later
when trying to do a register read.

[How]
At the start of the emulation, dc_link_set_preferred_link_settings()
and dp_retrain_link_dp_test() is called, even though it is connected
using a passive dongle.

Add an extra condition in dp_retrain_link_dp_test() to check for
link->dongle_max_pix_clk > 0. This is the only way we know if the
connection is using passive dongle so we don't retrain DP.

Signed-off-by: Samson Tam <Samson.Tam@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: swap system aperture high/low

[why]
Currently logical values are swapped in HW, causing
system aperture to be undefined, so VA and PA cannot co-exist

[how]
program values correctly

Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Set one 4:2:0-related PPS field as recommended by DSC spec

[why]
'second_line_offset_adj' was mistakenly left at zero, even though DSC spec
v1.2a recommends setting this field to 512 for 4:2:0.

[how]
Set 'second_line_offset_adj' to 512 for 4:2:0 and leave at zero otherwise

Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Set default block_size, even in unexpected cases

We're not expected to enter the default case, but not returning a
default value here is incorrect.

Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: early return when pipe_cnt is 0 in bw validation

[Why]
Unintentionally introduced behaviour change from previous refactor,
which causes clks to be 0 in no stream cases, which will cause
divide by 0.

[How]
Skip calculation of clocks when no stream. Which is the same as old
behaviour.

Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <tong.cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Update drm_dsc to reflect native 4.2.0 DSC spec

[Why]
Some parts of the DSC spec relating to 4.2.0 were not reflected in
drm_dsc_compute_rc_parameters, causing unexpected config failures

[How]
Add nsl_bpg_offset and rbs_min computation

Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Add aux tracing log in dce

[Why]
dce was re-arch'd, therefore adding aux tracing log into new dce

[How]
The porting from submit_channel_request/process_channel_reply of aux_engine_dce110.c

Signed-off-by: Chiawen Huang <chiawen.huang@amd.com>
Reviewed-by: Tony Cheng <tong.cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: No audio endpoint for Dell MST display

[Why]
There are certain MST displays (i.e. Dell P2715Q)
that although have the MST feature set to off may still
report it is a branch device and a non-zero
value for downstream port present.
This can lead to us incorrectly classifying a
dp dongle connection as being active and
disabling the audio endpoint for the display.

[How]
Modified the placement and
condition used to assign
the is_branch_dev bit.

Signed-off-by: Harmanprit Tatla <harmanprit.tatla@amd.com>
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: cap DCFCLK hardmin to 507 for NV10

[why]
Due to limitation in SMU/PPLIB, it is not possible to know Fmax @ Vmin for DCFCLK.
This causes issues at high display configurations where extra headroom of DCFCLK
can enable P-state switching

[how]
Use existing override logic. If override not defined, then force
min = 507

Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: move bw calc code into helpers

[Why]
For better readability and reusability

[How]
Move snippets of BW calculation code into helpers.

Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Fatemeh Darbehani <Fatemeh.Darbehani@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: 3.2.37

Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: fix dsc disable

A regression caused dsc to never get disabled in certain situations.

Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: fix up HUBBUB hw programming for VM

[why]
Some values were not being converted or bit-shifted properly for
HW registers, causing black screen

[how]
Fix up the values before programming HW

Signed-off-by: Jun Lei <jun.lei@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: 3.2.36

Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Add ability to set preferred link training parameters.

[WHY]
To add support for OS requirement to set preferred link training
parameters.

[HOW]
Create new structure of dp link training overrides. During link training
processes, these values should be used instead of the default training
parameters.

Signed-off-by: David Galiffi <David.Galiffi@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: initialize p_state to proper value

[why]
On some modes SMU will be in infinite loop state at boot, this is
because driver assumes p_state_support is false, but this is the
opposite of the assumed boot state by SMU. we optimize away
notifying SMU about no pstate, and so they will get stuck

[how]
when we init clk manager, init pstate to true, so it matches driver load
assumption

Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: use VCN firmware offset for cache window

Since we are using the signed FW now, and also using PSP firmware loading,
but it's still potential to break driver when loading FW directly
instead of PSP, so we should add offset.

Signed-off-by: Leo Liu <leo.liu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/ttm: use the same attributes when freeing d_page->vaddr

In function __ttm_dma_alloc_page(), d_page->addr is allocated
by dma_alloc_attrs() but freed with use dma_free_coherent() in
__ttm_dma_free_page().
Use the correct dma_free_attrs() to free d_page->vaddr.

Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/powerplay: change sysfs pp_dpm_xxx format for navi10

v2:
set average clock value on level 1 when current clock equal
min or max clock (fine grained dpm support).

the navi10 gfxclk (sclk) support fine grained DPM,
so use level 1 to show current dpm freq in sysfs pp_dpm_xxx

Signed-off-by: Kevin Wang <kevin1.wang@amd.com>
Reviewed-by: Kenneth Feng <kenneth.feng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: drop ras self test

this function is not needed any more. error injection is
the only way to validate ras but it can't be executed in
amdgpu_ras_init, where gpu is even not initialized

Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: only allow error injection to UMC IP block

error injection to other IP blocks (except UMC) will be enabled
until RAS feature stablize on those IP blocks

Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: disable GFX RAS by default

GFX RAS has not been stablized yet. disable GFX ras until
it is fully funcitonal.

Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: do not create ras debugfs/sysfs node for ASICs that don't have ras ability

driver shouldn't init any ras debugfs/sysfs node for ASICs that don't have ras
hardware ability

Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/powerplay: report bootup clock as max supported on dpm disabled

With gfxclk or uclk dpm disabled, it's reasonable to report bootup clock
as the max supported.

Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: Default disable GDS for compute VMIDs

The GDS and GWS blocks default to allowing all VMIDs to
access all entries. Graphics VMIDs can handle setting
these limits when the driver launches work. However,
compute workloads under HWS control don't go through the
kernel driver. Instead, HWS firmware should set these
limits when a process is put into a VMID slot.

Disable access to these devices by default by turning off
all mask bits (for OA) and setting BASE=SIZE=0 (for GDS
and GWS) for all compute VMIDs. If a process wants to use
these resources, they can request this from the HWS
firmware (when such capabilities are enabled). HWS will
then handle setting the base and limit for the process when
it is assigned to a VMID.

This will also prevent user kernels from getting 'stuck' in
GWS by accident if they write GWS-using code but HWS
firmware is not set up to handle GWS reset. Until HWS is
enabled to handle GWS properly, all GWS accesses will
MEM_VIOL fault the kernel.

v2: Move initialization outside of SRBM mutex

Signed-off-by: Joseph Greathouse <Joseph.Greathouse@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: exposing fica registers to df offsets

exposing fica registers to poll df pie data for xgmi error counters for
vega20.

Signed-off-by: Jonathan Kim <Jonathan.Kim@amd.com>
Reviewed-by: Alexander Deucher <Alexander.Deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/powerplay: input check for unsupported message/clock index

This can avoid them to be handled in a wrong way without notice.
Since not all SMU messages/clocks are supported on every SMU11 ASIC.

Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/powerplay: correct SW SMU valid mapping check

Current implementation is not actually able to detect
invalid message/table/workload mapping.

Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: flag arcturus as experimental for now

Current support will only work in internal engineering
boards.

Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: drop unused function definitions

These were dropped and the headers never got cleaned up.

Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu:add all VCN rings into schedule request queue

Add all VCN instances' decode/encode/jpeg decode rings into
drm_sched_rq list.

Signed-off-by: James Zhu <James.Zhu@amd.com>
Reviewed-by: Leo Liu <leo.liu@amd.com>
Reviewed-by: Boyuan Zhang <boyuan.zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdkfd: Increase vcrat size for GPU

GPU cache info (part of virtual CRAT) size depends on CU number.
For arcturus, CU number has been increased. So the required memory
for vcrat also increases.

Signed-off-by: Oak Zeng <Oak.Zeng@amd.com>
Reviewed-by: Yong Zhao <Yong.Zhao@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: enable all 8 sdma instances for Arcturus silicon

The more 6 sdma instances work fine now with DF fix in vbios:
* mmDF_PIE_AON_MiscClientsEnable(0x1c728)=0x3fe(DF_ALL_INSTANCE)
[9:4]MmhubsEnable=3f (change from 0)

Signed-off-by: Le Ma <le.ma@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdkfd: Merge gfx9/arcturus trap handlers, add ACC VGPR save

ACC VGPRs are a secondary VGPR set of same size as the primary VGPRs.
Save them as a block immediately following VGPRs.

Signed-off-by: Jay Cornwall <Jay.Cornwall@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: Add more detail to the VM fault printing

With the printing, we don't need to parse the value on our own any more.

Signed-off-by: Yong Zhao <Yong.Zhao@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdkfd: Add device id for real asics

Add pci device ids.

Signed-off-by: Oak Zeng <Oak.Zeng@amd.com>
Reviewed-by: Yong Zhao <Yong.Zhao@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: limit sdma instances to 2 for Arcturus in BU phase

Another 6 sdma instances do not work at present. Disable them to unblock KFD
for silicon bringup as a workaround

Signed-off-by: Le Ma <le.ma@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: skip gfx 9 common golden settings for arct

They are not needed by arct

Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdkfd: Add arcturus CWSR trap handler

CWSR (compute wave save/restore) is used for
preempting compute queues.

Signed-off-by: Oak Zeng <Oak.Zeng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

amd/powerplay: No SW XGMI dpm for Arcturus rev 2

xgmi dpm is handled by the SMU.

Signed-off-by: Yong Zhao <Yong.Zhao@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: clean up nonexistent firmware declaration for Arcturus

CPG firmwares are not used.

Signed-off-by: Le Ma <le.ma@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: init gds config for arct

arct has 4KB gds (4 banks inside) so the max_wave_id
should be 0xfff

Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Le Ma <Le.Ma@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: keep stolen memory for arct

Any dce register read back from arct is invalid. use hard code
stolen memory for arct until we validate the s3.

Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Le Ma <Le.Ma@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: init arct external rev id

Properly set the external silicon revision id.

Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Le Ma <Le.Ma@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: add arct gc golden settings

Golden GC register settings from the hw team.

Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Le Ma <Le.Ma@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: add arct sdma golden settings

Golden SDMA register settings from the hw team.

Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Le Ma <Le.Ma@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: add pci DID for Arcturus GL-XL.

Add device ids for Arcturus.

Signed-off-by: Feifei Xu <Feifei.Xu@amd.com>
Reviewed-by: Le Ma <Le.Ma@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: assign fb_start/end in mmhub v9.4 interface

Align with mmhub v1.0.

Signed-off-by: Le Ma <le.ma@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: add harvest support for Arcturus

Add VCN harvest support for Arcturus

Signed-off-by: James Zhu <James.Zhu@amd.com>
Reviewed-by: Leo Liu <leo.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: add multiple instances support for Arcturus

Arcturus has dual-VCN. Need add multiple instances support for Arcturus.

Signed-off-by: James Zhu <James.Zhu@amd.com>
Reviewed-by: Leo Liu <leo.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: modify amdgpu_vcn to support multiple instances

Arcturus has dual-VCN. Need Restruct amdgpu_device::vcn to support
multiple vcns. There are no any logical changes here

Signed-off-by: James Zhu <James.Zhu@amd.com>
Reviewed-by: Leo Liu <leo.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: add vcn nbio doorbell range setting for 2nd vcn instance

add vcn nbio doorbell range setting for 2nd vcn instance

Signed-off-by: James Zhu <James.Zhu@amd.com>
Reviewed-by: Leo Liu <leo.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu/: increase AMDGPU_MAX_RINGS to add 2nd vcn instance

increase AMDGPU_MAX_RINGS to add 2nd vcn instance

Signed-off-by: James Zhu <James.Zhu@amd.com>
Reviewed-by: Leo Liu <leo.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu/: add doorbell assignment for 2nd vcn instance

add doorbell assignment for 2nd vcn instance

Signed-off-by: James Zhu <James.Zhu@amd.com>
Reviewed-by: Leo Liu <leo.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu/: add ucodeID for 2nd vcn instance

add ucodeID for 2nd vcn instance

Signed-off-by: James Zhu <James.Zhu@amd.com>
Reviewed-by: Leo Liu <leo.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu/: add clientID for 2nd vcn instance

add clientID for 2nd vcn instance, remove unused SOC15_IH_CLIENTID_SYSHUB.

Signed-off-by: James Zhu <James.Zhu@amd.com>
Reviewed-by: Leo Liu <leo.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdkfd: Set number of xgmi optimized SDMA engines for arcturus

some sdma engines are optimized for xgmi on arcturus.

Signed-off-by: Oak Zeng <Oak.Zeng@amd.com>
Reviewed-by: Yong Zhao <Yong.Zhao@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: correct ip for mmHDP_READ_CACHE_INVALIDATE register access

Use the proper IP index for HDP registers.

Signed-off-by: Le Ma <le.ma@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: set system aperture to cover whole FB region in mmhub v9.4

In XGMI configuration, the FB region covers vram region from peer
device, adjust system aperture to cover all of them

Signed-off-by: Le Ma <le.ma@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: skip get/update xgmi topology info when no psp exists

We don't currently have psp support for arcturus so provide a alternative
mechanism in the meantime.

Signed-off-by: Le Ma <le.ma@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/powerplay: get smc firmware and pptable

get smc firmware and pptable for arcturus

Signed-off-by: Chengming Gui <Jack.Gui@amd.com>
Reviewed-by: Kevin Wang <kevin1.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu/powerplay: add smu11 driver interface for arcturus. (v2)

add smu11_driver_if_arcturus.h file.

v2: add license, fix header guard (Alex)

Signed-off-by: Chengming Gui <Jack.Gui@amd.com>
Reviewed-by: Kevin Wang <kevin1.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu/powerplay: add arcturus ppt functions

add arcturus_ppsmc.h arcturus_ppt.c and arcturus_ppt.h files.

This is the initial power management support for Arcturus.

Signed-off-by: Chengming Gui <Jack.Gui@amd.com>
Reviewed-by: Kevin Wang <kevin1.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: enable the Doorbell support for VCN2.5

Including decode, encode, and JPEG decode rings

Signed-off-by: Leo Liu <leo.liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: add vcn doorbell range function to nbio7.4 (v2)

To setup the aperture for VCN2.5

v2: setup vcn doorbells in vcn2.5 hw_init (Alex)

Signed-off-by: Leo Liu <leo.liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: enable VCN2.5 on Arcturus

VCN is the video decode and encode engine on Arcturus

Signed-off-by: Leo Liu <leo.liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu/VCN2.5: set JPEG decode ring functions

Also reuse most of the JPEG2.0 decode ring functions

Signed-off-by: Leo Liu <leo.liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: add JPEG2.5 HW start and stop

JPEG engine initialization and suspend sequences

Signed-off-by: Leo Liu <leo.liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu/VCN2.5: set encode ring functions

Also reuse most of the VCN2.0 encode ring functions

Signed-off-by: Leo Liu <leo.liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu/VCN2.5: set decode ring functions

Also reuse most of the VCN2.0 decode ring functions

Signed-off-by: Leo Liu <leo.liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: add Arcturus to the VCN family

including firmware support etc.

Signed-off-by: Leo Liu <leo.liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: add VCN2.5 VCPU start and stop

HW engine initialization and suspend sequences.

Signed-off-by: Leo Liu <leo.liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: add VCN2.5 basic supports

i.e. basic VCN IP SW structures

VCN is the video codec block on the GPU.

Signed-off-by: Leo Liu <leo.liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu/VCN2: expose rings functions

They can be reused by VCN2.x family

Signed-off-by: Leo Liu <leo.liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu/VCN2: put IB internal registers offset to structure

So the ring functions can be shared with different VCN versions
with different internal registers offsets

Signed-off-by: Leo Liu <leo.liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: declare sdma firmware binary files for Arcturus

So that they are properly picked up as a driver dependency.

Signed-off-by: Le Ma <le.ma@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: Clear build undefined warning

Add amdgpu_amdkfd_arcturus_get_functions stub when
CONFIG_HSA_AMD is undefinded.

Signed-off-by: James Zhu <James.Zhu@amd.com>
Reviewed-by: Yong Zhao <Yong.Zhao@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: Enable xgmi support for Arcturus

xgmi is a high performance cross-GPU communication channel.

Signed-off-by: Oak Zeng <Oak.Zeng@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: Hack xgmi topology info when there is no psp fw

This is only needed on emulation platform where psp fw might
not be available, to hack xgmi topology info such as hive id and
node id.

v2: Add offset to hacked hive/node id
v3: Don't use introduce new module parameter.

Signed-off-by: Oak Zeng <Oak.Zeng@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdkfd: Support MMHUB1 in kfd interrupt path

Handle interrupts for second mmhub.

Signed-off-by: Yong Zhao <Yong.Zhao@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: Set VM_L2_CNTL.PDE_FAULT_CLASSIFICATION to 0 for MMHUB 9.4

Should be set to 0 for mmhub 9.4.

Signed-off-by: Yong Zhao <Yong.Zhao@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdkfd: Implement kfd2kgd_calls for Arcturus

Arcturus shares most of the kfd2kgd_calls with gfx9. But due to
SDMA register address change, it can't share SDMA related functions.
Export gfx9 kfd2kgd_calls and implement SDMA related functions
for Arcturus.

Signed-off-by: Oak Zeng <Oak.Zeng@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdkfd: Fix sdma_bitmap overflow issue

In the original formula, when sdma queue number is 64,
the left shift overflows. Use an equivalence that won't
overflow.

Signed-off-by: Oak Zeng <Oak.Zeng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdkfd: Change arcturus sdma engines number

Arcturus has 8 sdma engines

Signed-off-by: Oak Zeng <Oak.Zeng@amd.com>
Reviewed-by: Yong Zhao <yong.zhao@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdkfd: Support two MMHUBs when setting up page table base in KFD

2 mmhubs on arcturus.

Signed-off-by: Yong Zhao <Yong.Zhao@amd.com>
Signed-off-by: Oak Zeng <Oak.Zeng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdkfd: Expose function mmhub_v9_4_setup_vm_pt_regs() for kfd to use

Signed-off-by: Yong Zhao <Yong.Zhao@amd.com>
Signed-off-by: Oak Zeng <Oak.Zeng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

amd/amdkfd: Add ASIC ARCTURUS to kfd

Add initial support for ARCTURUS to kfd.

Signed-off-by: Yong Zhao <Yong.Zhao@amd.com>
Signed-off-by: Oak Zeng <Oak.Zeng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdkfd: Support bigger gds size

Extend map_process and set_resources pm4 packet to support
bigger gds size for arcturus.

v2: Only make the change for v9

Signed-off-by: Oak Zeng <Oak.Zeng@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdkfd: Extend PM4 packets to support 8 SDMA

Extend map_queue and unmap_queue PM4 packets to support 8
SDMA engines. The new format is backward compatible.

Signed-off-by: Oak Zeng <Oak.Zeng@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: Initialize asic functions for Arcturus

After cherry-picking doorbell rework changes from drm-next
branch, Arcturus asic functions pointer need to be initialized
to init doorbell index for Arcturus.

Signed-off-by: Oak Zeng <Oak.Zeng@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: add paging queue support for 8 SDMA instances on Arcturus

Properly enable all 8 instances for paging queue.

Signed-off-by: Le Ma <le.ma@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: correct programming of ih_chicken for Arcturus

ih_chicken is a register that is not allowed to access by driver
in the L0 security policy.
psp bl need to enable field to allow driver to use physical
bus address for ih ring on secure part.

Signed-off-by: Le Ma <le.ma@amd.com>
Reviewed-by: Snow Zhang <snow.zhang@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: add Arcturus chip_name for init sdma microcode

So we load the proper firmware for arcturus.

Signed-off-by: Le Ma <le.ma@amd.com>
Acked-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: enable 8 SDMA instances for Arcturus

All the 8 SDMA instances work fine on the latest Gopher build model.

Signed-off-by: Le Ma <le.ma@amd.com>
Reviewed-by: Snow Zhang <Snow.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: correct Arcturus SDMA address space base index

Signed-off-by: Le Ma <le.ma@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: support sdma 2~7 doorbell range register offset

Update the doorbell range registers to support additional
SDMA rings.

Signed-off-by: Le Ma <le.ma@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>