Jonathan Bell [Tue, 13 Aug 2019 14:53:29 +0000 (15:53 +0100)]
xhci: Use more event ring segment table entries
Users have reported log spam created by "Event Ring Full" xHC event
TRBs. These are caused by interrupt latency in conjunction with a very
busy set of devices on the bus. The errors are benign, but throughput
will suffer as the xHC will pause processing of transfers until the
event ring is drained by the kernel. Expand the number of event TRB slots
available by increasing the number of event ring segments in the ERST.
Controllers have a hardware-defined limit as to the number of ERST
entries they can process, so make the actual number in use
min(ERST_MAX_SEGS, hw_max).
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.org>
Phil Elwell [Fri, 9 Aug 2019 07:51:43 +0000 (08:51 +0100)]
net: bcmgenet: Workaround #2 for Pi4 Ethernet fail
Some combinations of Pi 4Bs and Ethernet switches don't reliably get a
DCHP-assigned IP address, leaving the unit with a self=assigned 169.254
address. In the failure case, the Pi is left able to receive packets
but not send them, suggesting that the MAC<->PHY link is getting into
a bad state.
It has been found empirically that skipping a reset step by the genet
driver prevents the failures. No downsides have been discovered yet,
and unlike the forced renegotiation it doesn't increase the time to
get an IP address, so the workaround is enabled by default; add
genet.skip_umac_reset=n
to the command line to disable it.
See: https://github.com/raspberrypi/linux/issues/3108
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
James Hughes [Tue, 16 Jul 2019 11:18:21 +0000 (12:18 +0100)]
Add HDMI1 facility to the driver.
For generic ALSA, all you need is the bcm2835.h change, but
have also added structures for IEC958 HDMI. Not sure how to
test those.
Jonathan Bell [Thu, 1 Aug 2019 15:41:20 +0000 (16:41 +0100)]
hid: usb: Add device quirks for Freeway Airmouse T3 and MX3
These wireless mouse/keyboard combo remote control devices specify
multiple "wheel" events in their report descriptors. The wheel events
are incorrectly defined and apparently map to accelerometer data, leading
to spurious mouse scroll events being generated at an extreme rate when
the device is moved.
As a workaround, use HID_QUIRK_INCREMENT_USAGE_ON_DUPLICATE to mask
feeding the extra wheel events to the input subsystem.
See: https://github.com/raspberrypi/firmware/issues/1189
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.org>
Jonathan Bell [Thu, 9 May 2019 13:30:37 +0000 (14:30 +0100)]
drivers: char: add chardev for mmap'ing the RPiVid control registers
Based on the gpiomem driver, allow mapping of the decoder register
spaces such that userspace can access control/status registers.
This driver is intended for use with a custom ffmpeg backend accelerator
prior to a v4l2 driver being written.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.org>
driver: char: rpivid: Destroy the legacy device on remove
The legacy name support created a new device that was never destroyed.
If the driver was unloaded and reloaded, it failed due to the
device already existing.
Fixes: "75f1d14 driver: char: rpivid - also support legacy name"
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
driver: char: rpivid: Clean up error handling use of ERR_PTR/IS_ERR
The driver used an unnecessary intermediate void* variable so it
only called ERR_PTR once to convert to the error value.
Switch to converting as the error arises to remove these intermediate
variables.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
driver: char: rpivid: Add error handling to the legacy device load
The return value from device_create for the legacy device was never
checked or handled. Add the required error handling.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
driver: char: rpivid: Fix coding style whitespace issues.
Makes checkpatch happier.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
driver: char: rpimem: Add SPDX licence header.
Stops checkpatch complaining.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
driver: char: rpivid: Fix access to freed memory
The error path during probe frees the private memory block, and
then promptly dereferences it to log an error message.
Use the base device instead of the pointer to it in the private
structure.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Eric Anholt [Thu, 2 May 2019 20:22:53 +0000 (13:22 -0700)]
drm/v3d: Clock V3D down when not in use.
My various attempts at re-enabling runtime PM have failed, so just
crank the clock down when V3D is idle to reduce power consumption.
Signed-off-by: Eric Anholt <eric@anholt.net>
Eric Anholt [Mon, 14 Jan 2019 23:13:17 +0000 (15:13 -0800)]
drm/v3d: HACK: gut runtime pm for now.
Something is still unstable -- on starting a new glxgears from an idle
X11, I get an MMU violation in high addresses. The CTS also failed
quite quickly. With this, CTS progresses for an hour before OOMing
(allocating some big buffers when my board only has 600MB available to
Linux)
Signed-off-by: Eric Anholt <eric@anholt.net>
popcornmix [Tue, 6 Aug 2019 14:23:14 +0000 (15:23 +0100)]
clk-bcm2835: Avoid null pointer exception
clk_desc_array[BCM2835_PLLB] doesn't exist so we dereference null when iterating
Signed-off-by: popcornmix <popcornmix@gmail.com>
Phil Elwell [Fri, 12 Jul 2019 14:38:35 +0000 (15:38 +0100)]
i2c: bcm2835: Set clock-stretch timeout to 35ms
The BCM2835 I2C blocks have a register to set the clock-stretch
timeout - how long the device is allowed to hold SCL low - in bus
cycles. The current driver doesn't write to the register, therefore
the default value of 64 cycles is being used for all devices.
Set the timeout to the value recommended for SMBus - 35ms.
See: https://github.com/raspberrypi/linux/issues/3064
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Jonathan Bell [Thu, 11 Jul 2019 16:55:43 +0000 (17:55 +0100)]
xhci: add quirk for host controllers that don't update endpoint DCS
Seen on a VLI VL805 PCIe to USB controller. For non-stream endpoints
at least, if the xHC halts on a particular TRB due to an error then
the DCS field in the Out Endpoint Context maintained by the hardware
is not updated with the current cycle state.
Using the quirk XHCI_EP_CTX_BROKEN_DCS and instead fetch the DCS bit
from the TRB that the xHC stopped on.
See: https://github.com/raspberrypi/linux/issues/3060
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.org>
Eric Anholt [Mon, 14 Jan 2019 22:47:57 +0000 (14:47 -0800)]
drm/v3d: Hook up the runtime PM ops.
In translating the runtime PM code from vc4, I missed the ".pm"
assignment to actually connect them up. Fixes missing MMU setup if
runtime PM resets V3D.
Signed-off-by: Eric Anholt <eric@anholt.net>
(cherry picked from commit
ca197699af29baa8236c74c53d4904ca8957ee06)
Eric Anholt [Mon, 14 Jan 2019 20:35:43 +0000 (12:35 -0800)]
drm/v3d: Skip MMU flush if the device is currently off.
If it's off, we know it will be reset on poweron, so the MMU won't
have any TLB cached from before this point. Avoids failed waits for
MMU flush to reply.
Signed-off-by: Eric Anholt <eric@anholt.net>
(cherry picked from commit
3ee4e2e0a9e9587eacbb69b067bbc72ab2cdc47b)
Eric Anholt [Fri, 5 Oct 2018 00:22:43 +0000 (17:22 -0700)]
drm/v3d: Add support for 2711.
Signed-off-by: Eric Anholt <eric@anholt.net>
Phil Elwell [Tue, 11 Jun 2019 16:38:28 +0000 (17:38 +0100)]
arm: bcm2835: Add bcm2838 compatible string.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Jonathan Bell [Tue, 11 Jun 2019 10:42:03 +0000 (11:42 +0100)]
usbhid: call usb_fixup_endpoint after mangling intervals
Lets the mousepoll override mechanism work with xhci.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.org>
Jonathan Bell [Tue, 11 Jun 2019 10:33:39 +0000 (11:33 +0100)]
xhci: implement xhci_fixup_endpoint for interval adjustments
Must be called in a non-atomic context, after the endpoint
has been registered with the hardware via xhci_add_endpoint
and before the first URB is submitted for the endpoint.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.org>
Jonathan Bell [Tue, 11 Jun 2019 09:55:00 +0000 (10:55 +0100)]
usb: add plumbing for updating interrupt endpoint interval state
xHCI caches device and endpoint data after the interface is configured,
so an explicit command needs to be issued for any device driver wanting
to alter the polling interval of an endpoint.
Add usb_fixup_endpoint() to allow drivers to do this. The fixup must be
called after calculating endpoint bandwidth requirements but before any
URBs are submitted.
If polling intervals are shortened, any bandwidth reservations are no
longer valid but in practice polling intervals are only ever relaxed.
Limit the scope to interrupt transfers for now.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.org>
Eric Anholt [Thu, 2 May 2019 22:24:04 +0000 (15:24 -0700)]
clk: bcm2835: Allow reparenting leaf clocks while they're running.
This falls under the same "we can reprogram glitch-free as long as we
pause generation" rule as updating the div/frac fields. This can be
used for runtime reclocking of V3D to manage power leakage.
Signed-off-by: Eric Anholt <eric@anholt.net>
Eric Anholt [Thu, 2 May 2019 22:11:05 +0000 (15:11 -0700)]
clk: bcm2835: Add support for setting leaf clock rates while running.
As long as you wait for !BUSY, you can do glitch-free updates of clock
rate while the clock is running.
Signed-off-by: Eric Anholt <eric@anholt.net>
Eric Anholt [Sat, 12 Jan 2019 01:31:07 +0000 (17:31 -0800)]
soc: bcm: bcm2835-pm: Add support for 2711.
Without the actual power management part any more, there's a lot less
to set up for V3D. We just need to clear the RSTN field for the power
domain, and expose the reset controller for toggling it again.
This is definitely incomplete -- the old ISP and H264 is in the old
bridge, but since we have no consumers of it I've just done the
minimum to get V3D working.
Signed-off-by: Eric Anholt <eric@anholt.net>
Phil Elwell [Wed, 23 Jan 2019 16:11:50 +0000 (16:11 +0000)]
clk-bcm2835: Don't wait for pllh lock
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Martin Sperl [Mon, 13 May 2019 11:05:27 +0000 (11:05 +0000)]
spi: bcm2835: enable shared interrupt support
Add shared interrupt support for this driver.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Tim Gover [Fri, 22 Mar 2019 09:47:14 +0000 (09:47 +0000)]
usb: xhci: Disable the XHCI 5 second timeout
If the VL805 EEPROM has not been programmed then boot will hang for five
seconds. The timeout seems to be arbitrary and is an unecessary
delay on the first boot. Remove the timeout.
This is common code and probably can't be upstreamed unless the timeout
can be configurable somehow or perhaps the XHCI driver can be skipped
on the first boot.
Jonathan Bell [Tue, 14 May 2019 16:17:59 +0000 (17:17 +0100)]
net: genet: enable link energy detect powerdown for external PHYs
There are several warts surrounding bcmgenet_mii_probe() as this
function is called from ndo_open, but it's calling registration-type
functions. The probe should be called at probe time and refactored
such that the PHY device data can be extracted to limit the scope
of this flag to Broadcom PHYs.
For now, pass this flag in as it puts our attached PHY into a low-power
state when disconnected.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.org>
Phil Elwell [Wed, 27 Mar 2019 13:45:46 +0000 (13:45 +0000)]
bcmgenet: Better coalescing parameter defaults
Set defaults for TX and RX packet coalescing to be equivalent to:
# ethtool -C eth0 tx-frames 10
# ethtool -C eth0 rx-usecs 50
This may be something we want to set via DT parameters in the
future.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Jonathan Bell [Wed, 12 Sep 2018 13:44:53 +0000 (14:44 +0100)]
bcmgenet: constrain max DMA burst length
popcornmix [Tue, 30 Apr 2019 18:15:30 +0000 (19:15 +0100)]
bcm2835-pcm.c: Support multichannel audio
Phil Elwell [Thu, 1 Nov 2018 17:31:37 +0000 (17:31 +0000)]
vchiq: Add 36-bit address support
Conditional on a new compatible string, change the pagelist encoding
such that the top 24 bits are the pfn, leaving 8 bits for run length
(-1).
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
staging/vchiq_arm: Fix bcm2711 compatible string
Fixes: "vchiq: Add 36-bit address support"
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Phil Elwell [Fri, 2 Aug 2019 14:20:11 +0000 (15:20 +0100)]
mmc: sdhci-iproc: Fix vmmc regulators on iProc
The Linux support for controlling card power via regulators appears to
be contentious. I would argue that the default behaviour is contrary to
the SDHCI spec - turning off the power writes a reserved value to the
SD Bus Voltage Select field of the Power Control Register, which
seems to kill the Arasan/iProc controller - but fortunately there is a
hook in sdhci_ops to override the behaviour. Borrow the implementation
from sdhci_arasan_set_power.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Stefan Wahren [Sat, 4 May 2019 15:06:15 +0000 (17:06 +0200)]
hwrng: iproc-rng200: Add BCM2838 support
The HWRNG on the BCM2838 is compatible to iproc-rng200, so add the
support to this driver instead of bcm2835-rng.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
hwrng: iproc-rng200: Correct SoC name
The Pi 4 SoC is called BCM2711, not BCM2838.
Fixes: "hwrng: iproc-rng200: Add BCM2838 support"
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Phil Elwell [Wed, 29 May 2019 14:47:42 +0000 (15:47 +0100)]
arm: bcm2835: DMA can only address 1GB
The legacy peripherals can only address the first gigabyte of RAM, so
ensure that DMA allocations are restricted to that region.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Phil Elwell [Wed, 20 Feb 2019 08:49:39 +0000 (08:49 +0000)]
arm: bcm2835: Fix FIQ early ioremap
The ioremapping creates mappings within the vmalloc area. The
equivalent early function, create_mapping, now checks that the
requested explicit virtual address is between VMALLOC_START and
VMALLOC_END. As there is no reason to have any correlation between
the physical and virtual addresses, put the required mappings at
VMALLOC_START and above.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Phil Elwell [Wed, 12 Jun 2019 16:15:05 +0000 (17:15 +0100)]
w1: w1-gpio: Make GPIO an output for strong pullup
The logic to drive the data line high to implement a strong pullup
assumed that the pin was already an output - setting a value does
not change an input.
See: https://github.com/raspberrypi/firmware/issues/1143
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Dave Stevenson [Thu, 2 May 2019 14:50:01 +0000 (15:50 +0100)]
staging: mmal-vchiq: Fix memory leak in error path
On error, vchiq_mmal_component_init could leave the
event context allocated for ports.
Clean them up in the error path.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Dave Stevenson [Wed, 1 May 2019 12:27:23 +0000 (13:27 +0100)]
staging: mmal-vchiq: Free the event context for control ports
vchiq_mmal_component_init calls init_event_context for the
control port, but vchiq_mmal_component_finalise didn't free
it, causing a memory leak..
Add the free call.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Dave Stevenson [Mon, 18 Feb 2019 15:52:29 +0000 (15:52 +0000)]
staging: mmal-vchiq: Update mmal_parameters.h with recently defined params
mmal_parameters.h hasn't been updated to reflect additions made
over the last few years. Update it to reflect the currently
supported parameters.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Dave Stevenson [Wed, 13 Feb 2019 12:33:29 +0000 (12:33 +0000)]
staging: mmal_vchiq: Add in the Bayer encoding formats
The list of formats was copied before Bayer support was added.
The ISP supports Bayer and is being supported by the bcm2835_codec
driver, so add in the encodings for them.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Dave Stevenson [Tue, 18 Sep 2018 10:08:51 +0000 (11:08 +0100)]
media: ov5647: Use gpiod_set_value_cansleep
All calls to the gpio library are in contexts that can sleep,
therefore there is no issue with having those GPIOs controlled
by controllers which require sleeping (eg I2C GPIO expanders).
Switch to using gpiod_set_value_cansleep instead of gpiod_set_value
to avoid triggering the warning in gpiolib should the GPIO
controller need to sleep.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Dave Stevenson [Thu, 24 Jan 2019 15:09:28 +0000 (15:09 +0000)]
clk: clk-bcm2835: Use %zd when printing size_t
The debug text for how many clocks have been registered
uses "%d" with a size_t. Correct it to "%zd".
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Dave Stevenson [Tue, 22 Jan 2019 12:04:09 +0000 (12:04 +0000)]
staging: mmal-vchiq: Fix client_component for 64 bit kernel
The MMAL client_component field is used with the event
mechanism to allow the client to identify the component for
which the event is generated.
The field is only 32bits in size, therefore we can't use a
pointer to the component in a 64 bit kernel.
Component handles are already held in an array per VCHI
instance, so use the array index as the client_component handle
to avoid having to create a new IDR for this purpose.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Dave Stevenson [Mon, 29 Oct 2018 17:57:45 +0000 (17:57 +0000)]
media: videobuf2: Allow exporting of a struct dmabuf
videobuf2 only allowed exporting a dmabuf as a file descriptor,
but there are instances where having the struct dma_buf is
useful within the kernel.
Split the current implementation into two, one step which
exports a struct dma_buf, and the second which converts that
into an fd.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Dave Stevenson [Mon, 24 Sep 2018 17:26:02 +0000 (18:26 +0100)]
staging: vc04_services: Support sending data to MMAL ports
Add the ability to send data to ports. This only supports
zero copy mode as the required bulk transfer setup calls
are not done.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Dave Stevenson [Mon, 24 Sep 2018 17:15:38 +0000 (18:15 +0100)]
staging: mmal-vchiq: Add support for event callbacks.
(Preparation for the codec driver).
The codec uses the event mechanism to report things such as
resolution changes. It is signalled by the cmd field of the buffer
being non-zero.
Add support for passing this information out to the client.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Dave Stevenson [Mon, 29 Oct 2018 16:20:46 +0000 (16:20 +0000)]
staging: mmal-vchiq: Avoid use of bool in structures
Fixes up a checkpatch error "Avoid using bool structure members
because of possible alignment issues".
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Dave Stevenson [Thu, 22 Nov 2018 17:31:06 +0000 (17:31 +0000)]
media: tc358743: Return an appropriate colorspace from tc358743_set_fmt
When calling tc358743_set_fmt, the code was calling tc358743_get_fmt
to choose a valid format. However that sets the colorspace
based on what was read back from the chip. When you set the format,
then the driver would choose and program the colorspace based
on the format code.
The result was that if you called try or set format for UYVY
when the current format was RGB3 then you would get told sRGB,
and try RGB3 when current was UYVY and you would get told
SMPTE170M.
The value programmed into the chip is determined by this driver,
therefore there is no need to read back the value. Return the
colorspace based on the format set/tried instead.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Dave Stevenson [Wed, 31 Oct 2018 14:59:40 +0000 (14:59 +0000)]
MAINTAINERS: Add entry for BCM2835 Unicam driver
Adds entry for the new BCM2835 Unicam (CSI-2 receiver) driver
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Dave Stevenson [Wed, 31 Oct 2018 14:59:06 +0000 (14:59 +0000)]
dt-bindings: Document BCM283x CSI2/CCP2 receiver
Document the DT bindings for the CSI2/CCP2 receiver peripheral
(known as Unicam) on BCM283x SoCs.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Acked-by: Rob Herring <robh@kernel.org>
Dave Stevenson [Wed, 31 Oct 2018 14:58:08 +0000 (14:58 +0000)]
media: videodev2: Add helper defines for printing FOURCCs
New helper defines that allow printing of a FOURCC using
printf(V4L2_FOURCC_CONV, V4L2_FOURCC_CONV_ARGS(fourcc));
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Dave Stevenson [Wed, 31 Oct 2018 14:57:56 +0000 (14:57 +0000)]
media: adv7180: Add YPrPb support for ADV7282M
The ADV7282M can support YPbPr on AIN1-3, but this was
not selectable from the driver. Add it to the list of
supported input modes.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Dave Stevenson [Wed, 31 Oct 2018 14:57:46 +0000 (14:57 +0000)]
media: adv7180: Default to the first valid input
The hardware default is differential CVBS on AIN1 & 2, which
isn't very useful.
Select the first input that is defined as valid for the
chip variant (typically CVBS_AIN1).
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Dave Stevenson [Wed, 31 Oct 2018 14:57:34 +0000 (14:57 +0000)]
media: tc358743: Check I2C succeeded during probe.
The probe for the TC358743 reads the CHIPID register from
the device and compares it to the expected value of 0.
If the I2C request fails then that also returns 0, so
the driver loads thinking that the device is there.
Generally I2C communications are reliable so there is
limited need to check the return value on every transfer,
therefore only amend the one read during probe to check
for I2C errors.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Dave Stevenson [Wed, 31 Oct 2018 14:57:21 +0000 (14:57 +0000)]
media: tc358743: Add support for 972Mbit/s link freq.
Adds register setups for running the CSI lanes at 972Mbit/s,
which allows 1080P50 UYVY down 2 lanes.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Philipp Zabel [Thu, 21 Sep 2017 15:30:24 +0000 (17:30 +0200)]
media: tc358743: fix connected/active CSI-2 lane reporting
g_mbus_config was supposed to indicate all supported lane numbers, not
only the number of those currently in active use. Since the TC358743
can dynamically reduce the number of active lanes if the required
bandwidth allows for it, report all lane numbers up to the connected
number of lanes as supported in pdata mode.
In device tree mode, do not report lane count and clock mode at all, as
the receiver driver can determine these from the device tree.
To allow communicating the number of currently active lanes, add a new
bitfield to the v4l2_mbus_config flags. This is a temporary fix, to be
used only until a better solution is found.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Dave Stevenson [Wed, 31 Oct 2018 14:56:59 +0000 (14:56 +0000)]
media: tc358743: Increase FIFO level to 374.
The existing fixed value of 16 worked for UYVY 720P60 over
2 lanes at 594MHz, or UYVY 1080P60 over 4 lanes. (RGB888
1080P60 needs 6 lanes at 594MHz).
It doesn't allow for lower resolutions to work as the FIFO
underflows.
374 is required for 1080P24-30 UYVY over 2 lanes @ 972Mbit/s, but
>374 means that the FIFO underflows on 1080P50 UYVY over 2 lanes
@ 972Mbit/s.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Dave Stevenson [Wed, 31 Oct 2018 14:56:47 +0000 (14:56 +0000)]
media: ov5647: Add support for non-continuous clock mode
The driver was only supporting continuous clock mode
although this was not stated anywhere.
Non-continuous clock saves a small amount of power and
on some SoCs is easier to interface with.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Dave Stevenson [Wed, 31 Oct 2018 14:56:33 +0000 (14:56 +0000)]
media: ov5647: Add support for PWDN GPIO.
Add support for an optional GPIO connected to PWDN on the sensor.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Dave Stevenson [Wed, 31 Oct 2018 14:55:37 +0000 (14:55 +0000)]
media: ov5647: Add set_fmt and get_fmt calls.
There's no way to query the subdevice for the supported
resolutions.
Add set_fmt and get_fmt implementations.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
P33M [Thu, 2 May 2019 10:53:45 +0000 (11:53 +0100)]
lan78xx: use default alignment for rx buffers
The lan78xx uses a 12-byte hardware rx header, so there is no need
to allocate SKBs with NET_IP_ALIGN set. Removes alignment faults
in both dwc_otg and in ipv6 processing.
Phil Howard [Fri, 29 Mar 2019 10:53:14 +0000 (10:53 +0000)]
rtc: rv3028: Add backup switchover mode support
Signed-off-by: Phil Howard <phil@pimoroni.com>
Phil Elwell [Fri, 20 Jul 2018 21:03:41 +0000 (22:03 +0100)]
bcm2835-dma: Add support for per-channel flags
Add the ability to interpret the high bits of the dreq specifier as
flags to be included in the DMA_CS register. The motivation for this
change is the ability to set the DISDEBUG flag for SD card transfers
to avoid corruption when using the VPU debugger.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Phil Elwell [Tue, 5 Mar 2019 09:51:22 +0000 (09:51 +0000)]
lan78xx: EEE support is now a PHY property
Now that EEE support is a property of the PHY, use the PHY's DT node
when querying the EEE-related properties.
See: https://github.com/raspberrypi/linux/issues/2882
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Joshua Emele [Thu, 8 Nov 2018 00:07:40 +0000 (16:07 -0800)]
lan78xx: Debounce link events to minimize poll storm
The bInterval is set to 4 (i.e. 8 microframes => 1ms) and the only bit
that the driver pays attention to is "link was reset". If there's a
flapping status bit in that endpoint data, (such as if PHY negotiation
needs a few tries to get a stable link) then polling at a slower rate
would act as a de-bounce.
See: https://github.com/raspberrypi/linux/issues/2447
Dave Stevenson [Thu, 10 Jan 2019 17:58:06 +0000 (17:58 +0000)]
firmware: raspberrypi: Report the fw variant during probe
The driver already reported the firmware build date during probe.
The mailbox calls have been extended to also report the variant
1 = standard start.elf
2 = start_x.elf (includes camera stack)
3 = start_db.elf (includes assert logging)
4 = start_cd.elf (cutdown version for smallest memory footprint).
Log the variant during probe.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
firmware: raspberrypi: Report the fw git hash during probe
The firmware can now report the git hash from which it was built
via the mailbox, so report it during probe.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Phil Elwell [Mon, 26 Nov 2018 19:46:58 +0000 (19:46 +0000)]
net: lan78xx: Support auto-downshift to 100Mb/s
Ethernet cables with faulty or missing pairs (specifically pairs C and
D) allow auto-negotiation to 1000Mbs, but do not support the successful
establishment of a link. Add a DT property, "microchip,downshift-after",
to configure the number of auto-negotiation failures after which it
falls back to 100Mbs. Valid values are 2, 3, 4, 5 and 0, where 0 means
never downshift.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
James Hughes [Fri, 2 Nov 2018 11:55:49 +0000 (11:55 +0000)]
Update issue templates (#2736)
Serge Schneider [Tue, 2 Oct 2018 10:14:15 +0000 (11:14 +0100)]
drivers: thermal: step_wise: avoid throttling at hysteresis temperature after dropping below it
Signed-off-by: Serge Schneider <serge@raspberrypi.org>
Ram Chandrasekar [Mon, 7 May 2018 17:54:08 +0000 (11:54 -0600)]
drivers: thermal: step_wise: add support for hysteresis
Step wise governor increases the mitigation level when the temperature
goes above a threshold and will decrease the mitigation when the
temperature falls below the threshold. If it were a case, where the
temperature hovers around a threshold, the mitigation will be applied
and removed at every iteration. This reaction to the temperature is
inefficient for performance.
The use of hysteresis temperature could avoid this ping-pong of
mitigation by relaxing the mitigation to happen only when the
temperature goes below this lower hysteresis value.
Signed-off-by: Ram Chandrasekar <rkumbako@codeaurora.org>
Signed-off-by: Lina Iyer <ilina@codeaurora.org>
Phil Elwell [Tue, 6 Nov 2018 12:57:48 +0000 (12:57 +0000)]
sc16is7xx: Don't spin if no data received
See: https://github.com/raspberrypi/linux/issues/2676
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Stefan Wahren [Sat, 13 Oct 2018 11:31:21 +0000 (13:31 +0200)]
firmware: raspberrypi: Add backward compatible get_throttled
Avoid a hard userspace ABI change by adding a compatible get_throttled
sysfs entry. Its value is now feed by the GET_THROTTLED requests of the
new hwmon driver. The first access to get_throttled will generate
a warning.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Stefan Wahren [Sat, 6 Oct 2018 14:46:18 +0000 (16:46 +0200)]
hwmon: raspberrypi: Prevent voltage low warnings from filling log
Although the correct fix for low voltage warnings is to
improve the power supply, the current implementation
of the detection can fill the log if the warning
happens freqently. This replaces the logging with
slightly custom ratelimited logging.
Signed-off-by: James Hughes <james.hughes@raspberrypi.org>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
popcornmix [Mon, 17 Sep 2018 16:31:18 +0000 (17:31 +0100)]
cxd2880: CXD2880_SPI_DRV should select DVB_CXD2880 with MEDIA_SUBDRV_AUTOSELECT
Serge Schneider [Mon, 9 Jul 2018 11:54:25 +0000 (12:54 +0100)]
Add rpi-poe-fan driver
Signed-off-by: Serge Schneider <serge@raspberrypi.org>
PoE HAT driver cleanup
* Fix undeclared variable in rpi_poe_fan_suspend
* Add SPDX-License-Identifier
* Expand PoE acronym in Kconfig help
* Give clearer error message on of_property_count_u32_elems fail
* Add documentation
* Add vendor to of_device_id compatible string.
* Rename m_data_s struct to fw_data_s
* Fix typos
Fixes: #2665
Signed-off-by: Serge Schneider <serge@raspberrypi.org>
rpi-poe-fan: fix def_pwm1 writes
Signed-off-by: Serge Schneider <serge@raspberrypi.org>
Phil Elwell [Thu, 5 Apr 2018 13:46:11 +0000 (14:46 +0100)]
lan78xx: Move enabling of EEE into PHY init code
Enable EEE mode as soon as possible after connecting to the PHY, and
before phy_start. This avoids a second link negotiation, which speeds
up booting and stops the interface failing to become ready.
See: https://github.com/raspberrypi/linux/issues/2437
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Phil Elwell [Wed, 20 Jun 2018 11:20:01 +0000 (12:20 +0100)]
brcmfmac: Re-enable firmware roaming support
As of 4.18, a firmware that implements the update_connect_params
method but doesn't claim to support roaming causes an error. We
disabled firmware roaming in 4.4 [1] because it appeared to
prevent disconnects, but let's try with the current firmware to see
if things have improved.
[1] https://github.com/raspberrypi/linux/commit/
dd9188011786fb62a7960922f31e8e086fb2009b
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Dave Stevenson [Wed, 13 Jun 2018 14:21:10 +0000 (15:21 +0100)]
net: lan78xx: Disable TCP Segmentation Offload (TSO)
TSO seems to be having issues when packets are dropped and the
remote end uses Selective Acknowledge (SACK) to denote that
data is missing. The missing data is never resent, so the
connection eventually stalls.
There is a module parameter of enable_tso added to allow
further debugging without forcing a rebuild of the kernel.
https://github.com/raspberrypi/linux/issues/2449
https://github.com/raspberrypi/linux/issues/2482
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Phil Elwell [Thu, 14 Jun 2018 14:07:26 +0000 (15:07 +0100)]
of: configfs: Use of_overlay_fdt_apply API call
The published API to the dynamic overlay application mechanism now
takes a Flattened Device Tree blob as input so that it can manage the
lifetime of the unflattened tree. Conveniently, the new API call -
of_overlay_fdt_apply - is virtually a drop-in replacement for
create_overlay, which can now be deleted.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Phil Elwell [Thu, 14 Jun 2018 10:21:04 +0000 (11:21 +0100)]
irqchip: irq-bcm2835: Calc. FIQ_START at boot-time
ad83c7cb2f37 ("irqchip/irq-bcm2836: Add support for DT interrupt polarity")
changed the way that the BCM2836/7 local interrupts are mapped; instead
of being pre-mapped they are now mapped on-demand. A side effect of this
change is that the call to irq_of_parse_and_map from armctrl_of_init
creates a new mapping, forming a gap between the IRQs and the FIQs. This
gap breaks the FIQ<->IRQ mapping which up to now has been done by assuming:
1) that the value of FIQ_START is the same as the number of normal IRQs
that will be mapped (still true), and
2) that this value is also the offset between an IRQ and its equivalent
FIQ (which is no longer the case).
Remove both assumptions by measuring the interval between the last IRQ
and the last FIQ, passing it as the parameter to init_FIQ().
Fixes: https://github.com/raspberrypi/linux/issues/2432
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Phil Elwell [Sat, 12 May 2018 20:35:43 +0000 (21:35 +0100)]
firmware/raspberrypi: Notify firmware of a reboot
Register for reboot notifications, sending RPI_FIRMWARE_NOTIFY_REBOOT
over the mailbox interface on reception.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Nick Bulleid [Thu, 10 May 2018 20:57:02 +0000 (21:57 +0100)]
Add ability to export gpio used by gpio-poweroff
Signed-off-by: Nick Bulleid <nedbulleid@fastmail.com>
Added export feature to gpio-poweroff documentation
Signed-off-by: Nick Bulleid <nedbulleid@fastmail.com>
popcornmix [Mon, 14 Jul 2014 21:02:09 +0000 (22:02 +0100)]
hid: Reduce default mouse polling interval to 60Hz
Reduces overhead when using X
Phil Elwell [Fri, 9 Mar 2018 12:01:00 +0000 (12:01 +0000)]
lan78xx: Read initial EEE status from DT
Add two new DT properties:
* microchip,eee-enabled - a boolean to enable EEE
* microchip,tx-lpi-timer - time in microseconds to wait before entering
low power state
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
hdoverobinson [Tue, 13 Mar 2018 10:58:39 +0000 (06:58 -0400)]
added capture_clear option to pps-gpio via dtoverlay (#2433)
Phil Elwell [Tue, 20 Feb 2018 10:07:27 +0000 (10:07 +0000)]
i2c-gpio: Also set bus numbers from reg property
I2C busses can be assigned specific bus numbers using aliases in
Device Tree - string properties where the name is the alias and the
value is the path to the node. The current DT parameter mechanism
does not allow property names to be derived from a parameter value
in any way, so it isn't possible to generate unique or matching
aliases for nodes from an overlay that can generate multiple
instances, e.g. i2c-gpio.
Work around this limitation (at least temporarily) by allowing
the i2c adapter number to be initialised from the "reg" property
if present.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Eric Anholt [Wed, 14 Sep 2016 08:16:19 +0000 (09:16 +0100)]
raspberrypi-firmware: Export the general transaction function.
The vc4-firmware-kms module is going to be doing the MBOX FB call.
Signed-off-by: Eric Anholt <eric@anholt.net>
Phil Elwell [Mon, 11 Dec 2017 09:18:32 +0000 (09:18 +0000)]
ARM: Activate FIQs to avoid __irq_startup warnings
There is a new test in __irq_startup that the IRQ is activated, which
hasn't been the case for FIQs since they bypass some of the usual setup.
Augment enable_fiq to include a call to irq_activate to avoid the
warning.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Phil Elwell [Mon, 16 Jul 2018 13:40:13 +0000 (14:40 +0100)]
dwc-otg: FIQ: Fix "bad mode in data abort handler"
Create a semi-static mapping for the USB registers early in the boot
process, before additional kernel threads are started, so all threads
will have the mappings from the start. This avoids the need for
data aborts to lazily update them.
See: https://github.com/raspberrypi/linux/issues/2450
Signed-off-by: Floris Bos <bos@je-eigen-domein.nl>
Noralf Trønnes [Wed, 3 Jun 2015 10:26:13 +0000 (12:26 +0200)]
ARM: bcm2835: Set Serial number and Revision
The VideoCore bootloader passes in Serial number and
Revision number through Device Tree. Make these available to
userspace through /proc/cpuinfo.
Mainline status:
There is a commit in linux-next that standardize passing the serial
number through Device Tree (string: /serial-number):
ARM: 8355/1: arch: Show the serial number from devicetree in cpuinfo
There was an attempt to do the same with the revision number, but it
didn't get in:
[PATCH v2 1/2] arm: devtree: Set system_rev from DT revision
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Phil Elwell [Mon, 27 Nov 2017 17:14:54 +0000 (17:14 +0000)]
cgroup: Disable cgroup "memory" by default
Some Raspberry Pis have limited RAM and most users won't use the
cgroup memory support so it is disabled by default. Enable with:
cgroup_enable=memory
See: https://github.com/raspberrypi/linux/issues/1950
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
James Hughes [Tue, 14 Nov 2017 15:13:15 +0000 (15:13 +0000)]
AXI performance monitor driver (#2222)
Uses the debugfs I/F to provide access to the AXI
bus performance monitors.
Requires the new mailbox peripheral access for access
to the VPU performance registers, system bus access
is done using direct register reads.
Signed-off-by: James Hughes <james.hughes@raspberrypi.org>
raspberrypi_axi_monitor: suppress warning
Suppress the following warning by casting the pointer to and uintptr_t
before to u32:
Signed-off-by: Matteo Croce <mcroce@redhat.com>
popcornmix [Fri, 25 Aug 2017 18:18:13 +0000 (19:18 +0100)]
cache: export clean and invalidate
hack: cache: Fix linker error
Michael Zoran [Sat, 11 Feb 2017 09:18:31 +0000 (01:18 -0800)]
ARM64: Force hardware emulation of deprecated instructions.
Michael Zoran [Sun, 15 Jan 2017 05:43:57 +0000 (21:43 -0800)]
ARM64: Round-Robin dispatch IRQs between CPUs.
IRQ-CPU mapping is round robined on ARM64 to increase
concurrency and allow multiple interrupts to be serviced
at a time. This reduces the need for FIQ.
Signed-off-by: Michael Zoran <mzoran@crowfest.net>
popcornmix [Mon, 13 Apr 2015 16:16:29 +0000 (17:16 +0100)]
config: Add default configs
Phil Elwell [Thu, 17 Dec 2015 13:37:07 +0000 (13:37 +0000)]
hci_h5: Don't send conf_req when ACTIVE
Without this patch, a modem and kernel can continuously bombard each
other with conf_req and conf_rsp messages, in a demented game of tag.
Cheong2K [Fri, 26 Feb 2016 10:20:10 +0000 (18:20 +0800)]
brcm: adds support for BCM43341 wifi
brcmfmac: Disable power management
Disable wireless power saving in the brcmfmac WLAN driver. This is a
temporary measure until the connectivity loss resulting from power
saving is resolved.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
brcmfmac: Use original country code as a fallback
Commit
73345fd212980d2e28a5c6d83801c903bd773680:
brcmfmac: Configure country code using device specific settings
prevents region codes from working on devices that lack a region code
translation table. In the event of an absent table, preserve the old
behaviour of using the provided code as-is.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
brcmfmac: Plug memory leak in brcmf_fill_bss_param
See: https://github.com/raspberrypi/linux/issues/1471
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
brcmfmac: do not use internal roaming engine by default
Some evidence of curing disconnects with this disabled, so make it a default.
Can be overridden with module parameter roamoff=0
See: http://projectable.me/optimize-my-pi-wi-fi/
brcmfmac: Change stop_ap sequence
Patch from Broadcom/Cypress to resolve a customer error
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Revert "brcmfmac: Disable power management"
Shortly after the release of the Pi 3B, a loss of SSH connectivity
over WiFi was traced to the power management handling, so power
management was disabled. And so it has remained ever since.
Enabling power management saves 55mA (~270mW) on a Pi 4B, so is very
much worth the minimal effort of reverting this patch, which was
squashed and rebased many times since then to the commit hash is
meaningless.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Pantelis Antoniou [Wed, 3 Dec 2014 11:23:28 +0000 (13:23 +0200)]
OF: DT-Overlay configfs interface
This is a port of Pantelis Antoniou's v3 port that makes use of the
new upstreamed configfs support for binary attributes.
Original commit message:
Add a runtime interface to using configfs for generic device tree overlay
usage. With it its possible to use device tree overlays without having
to use a per-platform overlay manager.
Please see Documentation/devicetree/configfs-overlays.txt for more info.
Changes since v2:
- Removed ifdef CONFIG_OF_OVERLAY (since for now it's required)
- Created a documentation entry
- Slight rewording in Kconfig
Changes since v1:
- of_resolve() -> of_resolve_phandles().
Originally-signed-off-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
DT configfs: Fix build errors on other platforms
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
DT configfs: fix build error
There is an error when compiling rpi-4.6.y branch:
CC drivers/of/configfs.o
drivers/of/configfs.c:291:21: error: initialization from incompatible pointer type [-Werror=incompatible-pointer-types]
.default_groups = of_cfs_def_groups,
^
drivers/of/configfs.c:291:21: note: (near initialization for 'of_cfs_subsys.su_group.default_groups.next')
The .default_groups is linked list since commit
1ae1602de028acaa42a0f6ff18d19756f8e825c6.
This commit uses configfs_add_default_group to fix this problem.
Signed-off-by: Slawomir Stepien <sst@poczta.fm>
configfs: New of_overlay API
popcornmix [Tue, 23 Feb 2016 19:56:04 +0000 (19:56 +0000)]
bcm2835-virtgpio: Virtual GPIO driver
Add a virtual GPIO driver that uses the firmware mailbox interface to
request that the VPU toggles LEDs.
P33M [Wed, 21 Oct 2015 13:55:21 +0000 (14:55 +0100)]
rpi_display: add backlight driver and overlay
Add a mailbox-driven backlight controller for the Raspberry Pi DSI
touchscreen display. Requires updated GPU firmware to recognise the
mailbox request.
Signed-off-by: Gordon Hollingworth <gordon@raspberrypi.org>
Add Raspberry Pi firmware driver to the dependencies of backlight driver
Otherwise the backlight driver fails to build if the firmware
loading driver is not in the kernel
Signed-off-by: Alex Riesen <alexander.riesen@cetitec.com>
Joerg Schambacher [Fri, 16 Oct 2020 13:17:07 +0000 (15:17 +0200)]
Fixes a problem when module probes before i2c module is available
The driver crashed while a NULL pointer returned by i2c_get_adapter()
has been used to access the i2c bus functions.
The headphone probing function hb_hp_probe() now returns -EPROBE_DEFER
in case the i2c module has not been loaded yet.
Signed-off-by: Joerg Schambacher <joerg@i2audio.com>
Florian Meier [Mon, 25 Jan 2016 15:48:59 +0000 (15:48 +0000)]
Add support for all the downstream rpi sound card drivers
ASoC: Add support for Rpi-DAC
ASoC: Add prompt for ICS43432 codec
Without a prompt string, a config setting can't be included in a
defconfig. Give CONFIG_SND_SOC_ICS43432 a prompt so that Pi soundcards
can use the driver.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Add IQaudIO Sound Card support for Raspberry Pi
Set a limit of 0dB on Digital Volume Control
The main volume control in the PCM512x DAC has a range up to
+24dB. This is dangerously loud and can potentially cause massive
clipping in the output stages. Therefore this sets a sensible
limit of 0dB for this control.
Allow up to 24dB digital gain to be applied when using IQAudIO DAC+
24db_digital_gain DT param can be used to specify that PCM512x
codec "Digital" volume control should not be limited to 0dB gain,
and if specified will allow the full 24dB gain.
Modify IQAudIO DAC+ ASoC driver to set card/dai config from dt
Add the ability to set the card name, dai name and dai stream name, from
dt config.
Signed-off-by: DigitalDreamtime <clive.messer@digitaldreamtime.co.uk>
IQaudIO: auto-mute for AMP+ and DigiAMP+
IQAudIO amplifier mute via GPIO22. Add dt params for "one-shot" unmute
and auto mute.
Revision 2, auto mute implementing HiassofT suggestion to mute/unmute
using set_bias_level, rather than startup/shutdown....
"By default DAPM waits 5 seconds (pmdown_time) before shutting down
playback streams so a close/stop immediately followed by open/start
doesn't trigger an amp mute+unmute."
Tested on both AMP+ (via DAC+) and DigiAMP+, with both options...
dtoverlay=iqaudio-dacplus,unmute_amp
"one-shot" unmute when kernel module loads.
dtoverlay=iqaudio-dacplus,auto_mute_amp
Unmute amp when ALSA device opened by a client. Mute, with 5 second delay
when ALSA device closed. (Re-opening the device within the 5 second close
window, will cancel mute.)
Revision 4, using gpiod.
Revision 5, clean-up formatting before adding mute code.
- Convert tab plus 4 space formatting to 2x tab
- Remove '// NOT USED' commented code
Revision 6, don't attempt to "one-shot" unmute amp, unless card is
successfully registered.
Signed-off-by: DigitalDreamtime <clive.messer@digitaldreamtime.co.uk>
ASoC: iqaudio-dac: fix S24_LE format
Remove set_bclk_ratio call so 24-bit data is transmitted in
24 bclk cycles.
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: iqaudio-dac: use modern dai_link style
Signed-off-by: Matthias Reichl <hias@horus.com>
Added support for HiFiBerry DAC+
The driver is based on the HiFiBerry DAC driver. However HiFiBerry DAC+ uses
a different codec chip (PCM5122), therefore a new driver is necessary.
Add support for the HiFiBerry DAC+ Pro.
The HiFiBerry DAC+ and DAC+ Pro products both use the existing bcm sound driver with the DAC+ Pro having a special clock device driver representing the two high precision oscillators.
An addition bug fix is included for the PCM512x codec where by the physical size of the sample frame is used in the calculation of the LRCK divisor as it was found to be wrong when using 24-bit depth sample contained in a little endian 4-byte sample frame.
Limit PCM512x "Digital" gain to 0dB by default with HiFiBerry DAC+
24db_digital_gain DT param can be used to specify that PCM512x
codec "Digital" volume control should not be limited to 0dB gain,
and if specified will allow the full 24dB gain.
Add dt param to force HiFiBerry DAC+ Pro into slave mode
"dtoverlay=hifiberry-dacplus,slave"
Add 'slave' param to use HiFiBerry DAC+ Pro in slave mode,
with Pi as master for bit and frame clock.
Signed-off-by: DigitalDreamtime <clive.messer@digitaldreamtime.co.uk>
Fixed a bug when using 352.8kHz sample rate
Signed-off-by: Daniel Matuschek <daniel@hifiberry.com>
ASoC: pcm512x: revert downstream changes
This partially reverts commit
185ea05465aac8bf02a0d2b2f4289d42c72870b7
which was added by https://github.com/raspberrypi/linux/pull/1152
The downstream pcm512x changes caused a regression, it broke normal
use of the 24bit format with the codec, eg when using simple-audio-card.
The actual bug with 24bit playback is the incorrect usage
of physical_width in various drivers in the downstream tree
which causes 24bit data to be transmitted with 32 clock
cycles. So it's not the pcm512x that needs fixing, it's the
soundcard drivers.
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: hifiberry_dacplus: fix S24_LE format
Remove set_bclk_ratio call so 24-bit data is transmitted in
24 bclk cycles.
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: hifiberry_dacplus: transmit S24_LE with 64 BCLK cycles
Signed-off-by: Matthias Reichl <hias@horus.com>
hifiberry_dacplus: switch to snd_soc_dai_set_bclk_ratio
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: hifiberry_dacplus: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Add driver for rpi-proto
Forward port of 3.10.x driver from https://github.com/koalo
We are using a custom board and would like to use rpi 3.18.x
kernel. Patch works fine for our embedded system.
URL to the audio chip:
http://www.mikroe.com/add-on-boards/audio-voice/audio-codec-proto/
Playback tested with devicetree enabled.
Signed-off-by: Waldemar Brodkorb <wbrodkorb@conet.de>
ASoC: rpi-proto: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Add Support for JustBoom Audio boards
justboom-dac: Adjust for ALSA API change
As of 4.4, snd_soc_limit_volume now takes a struct snd_soc_card *
rather than a struct snd_soc_codec *.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
ASoC: justboom-dac: fix S24_LE format
Remove set_bclk_ratio call so 24-bit data is transmitted in
24 bclk cycles.
Also remove hw_params as it's no longer needed.
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: justboom-dac: use modern dai_link style
Signed-off-by: Matthias Reichl <hias@horus.com>
New AudioInjector.net Pi soundcard with low jitter audio in and out.
Contains the sound/soc/bcm ALSA machine driver and necessary alterations to the Kconfig and Makefile.
Adds the dts overlay and updates the Makefile and README.
Updates the relevant defconfig files to enable building for the Raspberry Pi.
Thanks to Phil Elwell (pelwell) for the review, simple-card concepts and discussion. Thanks to Clive Messer for overlay naming suggestions.
Added support for headphones, microphone and bclk_ratio settings.
This patch adds headphone and microphone capability to the Audio Injector sound card. The patch also sets the bit clock ratio for use in the bcm2835-i2s driver. The bcm2835-i2s can't handle an 8 kHz sample rate when the bit clock is at 12 MHz because its register is only 10 bits wide which can't represent the ch2 offset of 1508. For that reason, the rate constraint is added.
ASoC: audioinjector-pi-soundcard: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
New driver for RRA DigiDAC1 soundcard using WM8741 + WM8804
ASoC: digidac1-soundcard: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Add support for Dion Audio LOCO DAC-AMP HAT
Using dedicated machine driver and pcm5102a codec driver.
Signed-off-by: DigitalDreamtime <clive.messer@digitaldreamtime.co.uk>
ASoC: dionaudio_loco: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Allo Piano DAC boards: Initial 2 channel (stereo) support (#1645)
Add initial 2 channel (stereo) support for Allo Piano DAC (2.0/2.1) boards,
using allo-piano-dac-pcm512x-audio overlay and allo-piano-dac ALSA ASoC
machine driver.
NB. The initial support is 2 channel (stereo) ONLY!
(The Piano DAC 2.1 will only support 2 channel (stereo) left/right output,
pending an update to the upstream pcm512x codec driver, which will have
to be submitted via upstream. With the initial downstream support,
provided by this patch, the Piano DAC 2.1 subwoofer outputs will
not function.)
Signed-off-by: Baswaraj K <jaikumar@cem-solutions.net>
Signed-off-by: Clive Messer <clive.messer@digitaldreamtime.co.uk>
Tested-by: Clive Messer <clive.messer@digitaldreamtime.co.uk>
ASoC: allo-piano-dac: fix S24_LE format
Remove set_bclk_ratio call so 24-bit data is transmitted in
24 bclk cycles.
Also remove hw_params and ops as they are no longer needed.
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: allo-piano-dac: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Add support for Allo Piano DAC 2.1 plus add-on board for Raspberry Pi.
The Piano DAC 2.1 has support for 4 channels with subwoofer.
Signed-off-by: Baswaraj K <jaikumar@cem-solutions.net>
Reviewed-by: Vijay Kumar B. <vijaykumar@zilogic.com>
Reviewed-by: Raashid Muhammed <raashidmuhammed@zilogic.com>
Add clock changes and mute gpios (#1938)
Also improve code style and adhere to ALSA coding conventions.
Signed-off-by: Baswaraj K <jaikumar@cem-solutions.net>
Reviewed-by: Vijay Kumar B. <vijaykumar@zilogic.com>
Reviewed-by: Raashid Muhammed <raashidmuhammed@zilogic.com>
PianoPlus: Dual Mono & Dual Stereo features added (#2069)
allo-piano-dac-plus: Master volume added + fixes
Master volume added, which controls both DACs volumes.
See: https://github.com/raspberrypi/linux/pull/2149
Also fix initial max volume, default mode value, and unmute.
Signed-off-by: allocom <sparky-dev@allo.com>
ASoC: allo-piano-dac-plus: fix S24_LE format
Remove set_bclk_ratio call so 24-bit data is transmitted in
24 bclk cycles.
Signed-off-by: Matthias Reichl <hias@horus.com>
sound: bcm: Fix memset dereference warning
This warning appears with GCC 6.4.0 from toolchains.bootlin.com:
../sound/soc/bcm/allo-piano-dac-plus.c: In function ‘snd_allo_piano_dac_init’:
../sound/soc/bcm/allo-piano-dac-plus.c:711:30: warning: argument to ‘sizeof’ in ‘memset’ call is the same expression as the destination; did you mean to dereference it? [-Wsizeof-pointer-memaccess]
memset(glb_ptr, 0x00, sizeof(glb_ptr));
^
Suggested-by: Phil Elwell <phil@raspberrypi.org>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
ASoC: allo-piano-dac-plus: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Add support for Allo Boss DAC add-on board for Raspberry Pi. (#1924)
Signed-off-by: Baswaraj K <jaikumar@cem-solutions.net>
Reviewed-by: Deepak <deepak@zilogic.com>
Reviewed-by: BabuSubashChandar <babusubashchandar@zilogic.com>
Add support for new clock rate and mute gpios.
Signed-off-by: Baswaraj K <jaikumar@cem-solutions.net>
Reviewed-by: Deepak <deepak@zilogic.com>
Reviewed-by: BabuSubashChandar <babusubashchandar@zilogic.com>
ASoC: allo-boss-dac: fix S24_LE format
Remove set_bclk_ratio call so 24-bit data is transmitted in
24 bclk cycles.
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: allo-boss-dac: transmit S24_LE with 64 BCLK cycles
Signed-off-by: Matthias Reichl <hias@horus.com>
allo-boss-dac: switch to snd_soc_dai_set_bclk_ratio
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: allo-boss-dac: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Support for Blokas Labs pisound board
Pisound dynamic overlay (#1760)
Restructuring pisound-overlay.dts, so it can be loaded and unloaded dynamically using dtoverlay.
Print a logline when the kernel module is removed.
pisound improvements:
* Added a writable sysfs object to enable scripts / user space software
to blink MIDI activity LEDs for variable duration.
* Improved hw_param constraints setting.
* Added compatibility with S16_LE sample format.
* Exposed some simple placeholder volume controls, so the card appears
in volumealsa widget.
Add missing SND_PISOUND selects dependency to SND_RAWMIDI
Without it the Pisound module fails to compile.
See https://github.com/raspberrypi/linux/issues/2366
Updates for Pisound module code:
* Merged 'Fix a warning in DEBUG builds' (1c8b82b).
* Updating some strings and copyright information.
* Fix for handling high load of MIDI input and output.
* Use dual rate oversampling ratio for 96kHz instead of single
rate one.
Signed-off-by: Giedrius Trainavicius <giedrius@blokas.io>
Fixing memset call in pisound.c
Signed-off-by: Giedrius Trainavicius <giedrius@blokas.io>
Fix for Pisound's MIDI Input getting blocked for a while in rare cases.
There was a possible race condition which could lead to Input's FIFO queue
to be underflown, causing high amount of processing in the worker thread for
some period of time.
Signed-off-by: Giedrius Trainavicius <giedrius@blokas.io>
Fix for Pisound kernel module in Real Time kernel configuration.
When handler of data_available interrupt is fired, queue_work ends up
getting called and it can block on a spin lock which is not allowed in
interrupt context. The fix was to run the handler from a thread context
instead.
Pisound: Remove spinlock usage around spi_sync
ASoC: pisound: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
ASoC: pisound: fix the parameter for spi_device_match
Signed-off-by: Hui Wang <hui.wang@canonical.com>
ASoC: Add driver for Cirrus Logic Audio Card
Note: due to problems with deferred probing of regulators
the following softdep should be added to a modprobe.d file
softdep arizona-spi pre: arizona-ldo1
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: rpi-cirrus: use modern dai_link style
Signed-off-by: Matthias Reichl <hias@horus.com>
sound: Support for Dion Audio LOCO-V2 DAC-AMP HAT
Signed-off-by: Miquel Blauw <info@dionaudio.nl>
ASoC: dionaudio_loco-v2: fix S24_LE format
Remove set_bclk_ratio call so 24-bit data is transmitted in
24 bclk cycles.
Also remove hw_params and ops as they are no longer needed.
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: dionaudio_loco-v2: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Add support for Fe-Pi audio sound card. (#1867)
Fe-Pi Audio Sound Card is based on NXP SGTL5000 codec.
Mechanical specification of the board is the same the Raspberry Pi Zero.
3.5mm jacks for Headphone/Mic, Line In, and Line Out.
Signed-off-by: Henry Kupis <fe-pi@cox.net>
ASoC: fe-pi-audio: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Add support for the AudioInjector.net Octo sound card
AudioInjector Octo: sample rates, regulators, reset
This patch adds new sample rates to the Audioinjector Octo sound card. The
new supported rates are (in kHz) :
96, 48, 32, 24, 16, 8, 88.2, 44.1, 29.4, 22.05, 14.7
Reference the bcm270x DT regulators in the overlay.
This patch adds a reset GPIO for the AudioInjector.net octo sound card.
Audioinjector octo : Make the playback and capture symmetric
This patch ensures that the sample rate and channel count of the audioinjector
octo sound card are symmetric.
audioinjector-octo: Add continuous clock feature
By user request, add a switch to prevent the clocks being stopped when
the stream is paused, stopped or shutdown. Provide access to the switch
by adding a 'non-stop-clocks' parameter to the audioinjector-addons
overlay.
See: https://github.com/raspberrypi/linux/issues/2409
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
sound: Fixes for audioinjector-octo under 4.19
1. Move the DT alias declaration to the I2C shim in the cases
where the shim is enabled. This works around a problem caused by a
4.19 commit [1] that generates DT/OF uevents for I2C drivers.
2. Fix the diagnostics in an error path of the soundcard driver to
correctly identify the reason for the failure to load.
3. Move the declaration of the clock node in the overlay outside
the I2C node to avoid warnings.
4. Sort the overlay nodes so that dependencies are only to earlier
fragments, in an attempt to get runtime dtoverlay application to
work (it still doesn't...)
See: https://github.com/Audio-Injector/Octo/issues/14
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
[1]
af503716ac14 ("i2c: core: report OF style module alias for devices registered via OF")
ASoC: audioinjector-octo-soundcard: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Driver support for Google voiceHAT soundcard.
ASoC: googlevoicehat-codec: Use correct device when grabbing GPIO
The fixup for the VoiceHAT in 4.18 incorrectly tried to find the
sdmode GPIO pin under the card device, not the codec device.
This failed, and therefore caused the device probe to fail.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
ASoC: googlevoicehat-codec: Reformat for kernel coding standards
Fix all whitespace, indentation, and bracing errors.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
ASoC: googlevoicehat-codec: Make driver function structure const
Make voicehat_component_driver a const structure.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
ASoC: googlevoicehat-codec: Only convert from ms to jiffies once
Minor optimisation and allows to become checkpatch clean.
A msec value is read out of DT or from a define, and convert once to
jiffies, rather than every time that it is used.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Driver and overlay for Allo Katana DAC
Allo Katana DAC: Updated default values
Signed-off-by: Jaikumar <jaikumar@cem-solutions.com>
Added mute stream func
Signed-off-by: Jaikumar <jaikumar@cem-solutions.net>
codecs: Correct Katana minimum volume
Update Katana minimum volume to get the exact 0.5 dB value in each step.
Signed-off-by: Sudeep Kumar <sudeepkumar@cem-solutions.net>
ASoC: Add generic RPI driver for simple soundcards.
The RPI simple sound card driver provides a generic ALSA SOC card driver
supporting a variety of Pi HAT soundcards. The intention is to avoid
the duplication of code for cards that can't be fully supported by
the soc simple/graph cards but are otherwise almost identical.
This initial commit adds support for the ADAU1977 ADC, Google VoiceHat,
HifiBerry AMP, HifiBerry DAC and RPI DAC.
Signed-off-by: Tim Gover <tim.gover@raspberrypi.org>
ASoC: Use correct card name in rpi-simple driver
Use the specific card name from drvdata instead of the snd_rpi_simple
rpi-simple-soundcard: Use nicer driver name "RPi-simple"
Rename the driver from "RPI simple soundcard" to "RPi-simple" so that
the driver name won't be mangled allowing to be used unaltered as the
card conf filename.
ASoC: rpi-simple-soundcard: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
ASoC: Add Kconfig and Makefile for sound/soc/bcm
Signed-off-by: popcornmix <popcornmix@gmail.com>
ASoC: Create a generic Pi Hat WM8804 driver
Reduce the amount of duplicated code by creating a generic driver for
Pi Hat digi cards using the WM8804 codec.
This replaces the
Allo DigiOne, Hifiberry Digi/Pro, JustBoom Digi and IQAudIO Digi
dedicate soundcard drivers with a generic driver.
There are no significant changes to the runtime behavior of the drivers
and end users should not have to change any configuration settings
after upgrading.
Minor changes
* Check the return value of snd_soc_component_update_bits
* Added some pr_debug tracing
* Various checkpatch tidyups
* Updated allodigi-one to use use 128FS at > 96 Khz. This appears to
be an omission in the original driver code so followed the Hifiberry
DAC driver approach.
ASoC: rpi-wm8804-soundcard: use modern dai_link style
Signed-off-by: Matthias Reichl <hias@horus.com>
rpi-wm8804-soundcard: drop PWRDN register writes
Since kernel 4.0 the PWRDN register bits are under DAPM
control from the wm8804 driver.
Drop code that modifies that register to avoid interfering
with DAPM.
Signed-off-by: Matthias Reichl <hias@horus.com>
rpi-wm8804-soundcard: configure wm8804 clocks only on rate change
This should avoid clicks when stopping and immediately afterwards
starting a stream with the same samplerate as before.
Signed-off-by: Matthias Reichl <hias@horus.com>
rpi-wm8804-soundcard: Fixed MCLKDIV for Allo Digione
The Allo Digione board wants a fixed MCLKDIV of 256.
See: https://github.com/raspberrypi/linux/issues/3296
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
ASoC: Add support for AudioSense-Pi add-on soundcard
AudioSense-Pi is a RPi HAT based on a TI's TLV320AIC32x4 stereo codec
This hardware provides multiple audio I/O capabilities to the RPi.
The codec connects to the RPi's SoC through the I2S Bus.
The following devices can be connected through a 3.5mm jack
1. Line-In: Plain old audio in from mobile phones, PCs, etc.,
2. Mic-In: Connect a microphone
3. Line-Out: Connect the output to a speaker
4. Headphones: Connect a Headphone w or w/o microphones
Multiple Inputs:
It supports the following combinations
1. Two stereo Line-Inputs and a microphone
2. One stereo Line-Input and two microphones
3. Two stereo Line-Inputs, a microphone and
one mono line-input (with h/w hack)
4. One stereo Line-Input, two microphones and
one mono line-input (with h/w hack)
Multiple Outputs:
Audio output can be routed to the headphones or
speakers (with additional hardware)
Signed-off-by: b-ak <anur.bhargav@gmail.com>
ASoC: audiosense-pi: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Added driver for the HiFiBerry DAC+ ADC (#2694)
Signed-off-by: Daniel Matuschek <daniel@hifiberry.com>
hifiberry_dacplusadc: switch to snd_soc_dai_set_bclk_ratio
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: hifiberry_dacplusadc: fix DAI link setup
The driver only defines a single DAI link and the code that tries
to setup the second (non-existent) DAI link looks wrong - using dmic
as a CPU/platform driver doesn't make any sense.
The DT overlay doesn't define a dmic property, so the code was never
executed (otherwise it would have resulted in a memory corruption).
So drop the offending code to prevent issues if a dmic property
should be added to the DT overlay.
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: hifiberry_dacplusadc: use modern dai_link style
Signed-off-by: Matthias Reichl <hias@horus.com>
Audiophonics I-Sabre 9038Q2M DAC driver
Signed-off-by: Audiophonics <contact@audiophonics.fr>
ASoC: i-sabre-q2m: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Added IQaudIO Pi-Codec board support (#2969)
Add support for the IQaudIO Pi-Codec board.
Signed-off-by: Gordon <gordon@iqaudio.com>
Fixed 48k timing issue
ASoC: iqaudio-codec: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
adds the Hifiberry DAC+ADC PRO version
This adds the driver for the DAC+ADC PRO version of the Hifiberry soundcard with software controlled PCM1863 ADC
Signed-off-by: Joerg Schambacher joerg@i2audio.com
Add Hifiberry DAC+DSP soundcard driver (#3224)
Adds the driver for the Hifiberry DAC+DSP. It supports capture and
playback depending on the DSP firmware.
Signed-off-by: Joerg Schambacher <joerg@i2audio.com>
Allow simultaneous use of JustBoom DAC and Digi
Signed-off-by: Johannes Krude <johannes@krude.de>
Pisound: MIDI communication fixes for scaled down CPU.
* Increased maximum SPI communication speed to avoid running too slow
when the CPU is scaled down and losing MIDI data.
* Keep track of buffer usage in millibytes for higher precision.
Signed-off-by: Giedrius Trainavičius <giedrius@blokas.io>
sound: Add the HiFiBerry DAC+HD version
This adds the driver for the DAC+HD version supporting HiFiBerry's
PCM179x based DACs. It also adds PLL control for clock generation.
Signed-off-by: Joerg Schambacher <joerg@i2audio.com>
Fix master mode settings of HiFiBerry DAC+ADC PRO card (#3424)
This patch fixes the board DAI setting when in master-mode.
Wrong setting could have caused random pop noise.
Signed-off-by: Joerg Schambacher <joerg@i2audio.com>
adds LED OFF feature to HiFiBerry DAC+ADC PRO sound card
This adds a DT overlay parameter 'leds_off' which allows
to switch off the onboard activity LEDs at all times
which has been requested by some users.
Signed-off-by: Joerg Schambacher <joerg@i2audio.com>
adds LED OFF feature to HiFiBerry DAC+ADC sound card
This adds a DT overlay parameter 'leds_off' which allows
to switch off the onboard activity LEDs at all times
which has been requested by some users.
Signed-off-by: Joerg Schambacher <joerg@i2audio.com>
adds LED OFF feature to HiFiBerry DAC+/DAC+PRO sound cards
This adds a DT overlay parameter 'leds_off' which allows
to switch off the onboard activity LEDs at all times
which has been requested by some users.
Signed-off-by: Joerg Schambacher <joerg@i2audio.com>
pisound: Added reading Pisound board hardware revision and exposing it (#3425)
pisound: Added reading Pisound board hardware revision and exposing it in kernel log and sysfs file:
/sys/kernel/pisound/hw_version
Signed-off-by: Giedrius <giedrius@blokas.io>
Added driver for HiFiBerry Amp amplifier add-on board
The driver contains a low-level hardware driver for the TAS5713 and the
drivers for the Raspberry Pi I2S subsystem.
TAS5713: return error if initialisation fails
Existing TAS5713 driver logs errors during initialisation, but does not return
an error code. Therefore even if initialisation fails, the driver will still be
loaded, but won't work. This patch fixes this. I2C communication error will now
reported correctly by a non-zero return code.
HiFiBerry Amp: fix device-tree problems
Some code to load the driver based on device-tree-overlays was missing. This is added by this patch.
According to 5713 pdf doc CLOCK_CTRL is a readonly status register, and it behaves so. Remove useless setting
sound: pcm512x-codec: Adding 352.8kHz samplerate support
sound/soc: only first codec is master in multicodec setup
When using multiple codecs, at most one codec should generate the master
clock. All codecs except the first are therefore configured for slave
mode.
Signed-off-by: Johannes Krude <johannes@krude.de>
ASoC: Fix snd_soc_get_pcm_runtime usage
Commit [1] changed the snd_soc_get_pcm_runtime to take a dai_link
pointer instead of a string. Patch up the downstream drivers to use
the modified API.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
[1]
4468189ff307 ("ASoC: soc-core: find rtd via dai_link pointer at snd_soc_get_pcm_runtime()")
Add support for the AudioInjector.net Isolated sound card
This patch adds support for the Audio Injector Isolated sound card.
Signed-off-by: Matt Flax <flatmax@flatmax.org>
Add support for merus-amp soundcard and ma120x0p codec
Add 96KHz rate support to MA120X0P codec and make enable and mute gpio
pins optional.
Signed-off-by: AMuszkat <ariel.muszkat@gmail.com>
Fixes a problem with clock settings of HiFiBerry DAC+ADC PRO (#3545)
This patch fixes a problem of the re-calculation of
i2s-clock and -parameter settings when only the ADC is activated.
Signed-off-by: Joerg Schambacher <joerg@i2audio.com>
configs: Enable the AD193x codecs
See: https://github.com/raspberrypi/linux/issues/2850
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Switch to snd_soc_dai_set_bclk_ratio
Replaces obsolete function snd_soc_dai_set_tdm_slot
Signed-off-by: Joerg Schambacher <joerg@i2audio.com>
Enhances the DAC+ driver to control the optional headphone amplifier
Probes on the I2C bus for TPA6130A2, if successful, it sets DT-parameter
'status' from 'disabled' to 'okay' using change_sets to enable
the headphone control.
Signed-off-by: Joerg Schambacher joerg@i2audio.com