iio: imu: inv_mpu6050: fix suspend/resume with runtime power

Suspend/resume were not working correctly with pm runtime.
Now suspend check if the chip is already suspended, and
resume put runtime pm in the correct state.

Issues seen prior to this were:

When entering suspend, there was an error in logs because we
were disabling vddio regulator although it was already disabled.
And when resuming, the chip was pull back to full power but the
pm_runtime state was not updated. So it was believing it was
still suspended.

Fixes: 4599cac84614 ("iio: imu: inv_mpu6050: use runtime pm with autosuspend")
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: st_sensors: rely on odr mask to know if odr can be set

Indeed, relying on addr being not 0 cannot work because some device have
their register to set odr at address 0. As a matter of fact, if the odr
can be set, then there is a mask.

Sensors with ODR register at address 0 are: lsm303dlh, lsm303dlhc, lsm303dlm

Fixes: 7d245172675a ("iio: common: st_sensors: check odr address value in st_sensors_set_odr()")
Signed-off-by: Lary Gibaud <yarl-baudig@mailoo.org>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: xilinx-xadc: Make sure not exceed maximum samplerate

The XADC supports a samplerate of up to 1MSPS. Unfortunately the hardware
does not have a FIFO, which means it generates an interrupt for each
conversion sequence. At one 1MSPS this creates an interrupt storm that
causes the system to soft-lock.

For this reason the driver limits the maximum samplerate to 150kSPS.
Currently this check is only done when setting a new samplerate. But it is
also possible that the initial samplerate configured in the FPGA bitstream
exceeds the limit.

In this case when starting to capture data without first changing the
samplerate the system can overload.

To prevent this check the currently configured samplerate in the probe
function and reduce it to the maximum if necessary.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Fixes: bdc8cda1d010 ("iio:adc: Add Xilinx XADC driver")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: xilinx-xadc: Fix sequencer configuration for aux channels in simultaneous mode

The XADC has two internal ADCs. Depending on the mode it is operating in
either one or both of them are used. The device manual calls this
continuous (one ADC) and simultaneous (both ADCs) mode.

The meaning of the sequencing register for the aux channels changes
depending on the mode.

In continuous mode each bit corresponds to one of the 16 aux channels. And
the single ADC will convert them one by one in order.

In simultaneous mode the aux channels are split into two groups the first 8
channels are assigned to the first ADC and the other 8 channels to the
second ADC. The upper 8 bits of the sequencing register are unused and the
lower 8 bits control both ADCs. This means a bit needs to be set if either
the corresponding channel from the first group or the second group (or
both) are set.

Currently the driver does not have the special handling required for
simultaneous mode. Add it.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Fixes: bdc8cda1d010 ("iio:adc: Add Xilinx XADC driver")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: xilinx-xadc: Fix clearing interrupt when enabling trigger

When enabling the trigger and unmasking the end-of-sequence (EOS) interrupt
the EOS interrupt should be cleared from the status register. Otherwise it
is possible that it was still set from a previous capture. If that is the
case the interrupt would fire immediately even though no conversion has
been done yet and stale data is being read from the device.

The old code only clears the interrupt if the interrupt was previously
unmasked. Which does not make much sense since the interrupt is always
masked at this point and in addition masking the interrupt does not clear
the interrupt from the status register. So the clearing needs to be done
unconditionally.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Fixes: bdc8cda1d010 ("iio:adc: Add Xilinx XADC driver")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: xilinx-xadc: Fix ADC-B powerdown

The check for shutting down the second ADC is inverted. This causes it to
be powered down when it should be enabled. As a result channels that are
supposed to be handled by the second ADC return invalid conversion results.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Fixes: bdc8cda1d010 ("iio:adc: Add Xilinx XADC driver")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: dac: ad5770r: fix off-by-one check on maximum number of channels

Currently there is an off-by-one check on the number of channels that
will cause an arry overrun in array st->output_mode when calling the
function d5770r_store_output_range. Fix this by using >= rather than >
to check for maximum number of channels.

Addresses-Coverity: ("Out-of-bounds access")
Fixes: cbbb819837f6 ("iio: dac: ad5770r: Add AD5770R support")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: imu: st_lsm6dsx: flush hw FIFO before resetting the device

flush hw FIFO before device reset in order to avoid possible races
on interrupt line 1. If the first interrupt line is asserted during
hw reset the device will work in I3C-only mode (if it is supported)

Fixes: 801a6e0af0c6 ("iio: imu: st_lsm6dsx: add support to LSM6DSO")
Fixes: 43901008fde0 ("iio: imu: st_lsm6dsx: add support to LSM6DSR")
Reported-by: Mario Tesi <mario.tesi@st.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Vitor Soares <vitor.soares@synopsys.com>
Tested-by: Vitor Soares <vitor.soares@synopsys.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: core: Fix handling of 'dB'

This patch fixes the call to iio_str_to_fixpoint when using 'dB' sufix.
Before this the scale_db was not used when parsing the string written to
the attribute and it failed with invalid value.

Fixes: b8528224741b ("iio: core: Handle 'dB' suffix in core")
Signed-off-by: Mircea Caprioru <mircea.caprioru@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

dt-bindings: iio: adc: stm32-adc: fix id relative path

Fix id relative path that shouldn't contain 'bindings', as pointed out
when submitting st,stm32-dac bindings conversion to json-schema [1].
[1] https://patchwork.ozlabs.org/patch/1257568/

Fixes: a8cf1723c4b7 ("dt-bindings: iio: adc: stm32-adc: convert bindings to json-schema")

Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

counter: 104-quad-8: Add lock guards - generic interface

Add lock protection from race conditions to 104-quad-8 counter driver
generic interface code changes. Mutex calls used for protection.

Fixes: f1d8a071d45b ("counter: 104-quad-8: Add Generic Counter interface support")

Signed-off-by: Syed Nayyar Waris <syednwaris@gmail.com>
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: imu: st_lsm6dsx: specify slave odr in slv_odr

Introduce slv_odr in ext_info data structure in order to distinguish
between sensor hub trigger (accel sensor) odr and i2c slave odr and
properly compute samples in FIFO pattern

Fixes: e485e2a2cfd6 ("iio: imu: st_lsm6dsx: enable sensor-hub support for lsm6dsm")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: imu: st_lsm6dsx: fix read misalignment on untagged FIFO

st_lsm6dsx suffers of a read misalignment on untagged FIFO when
all 3 supported sensors (accel, gyro and ext device) are running
at different ODRs (the use-case is reported in the LSM6DSM Application
Note at pag 100).
Fix the issue taking into account decimation factor reading the FIFO
pattern.

Fixes: e485e2a2cfd6 ("iio: imu: st_lsm6dsx: enable sensor-hub support for lsm6dsm")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: stm32-adc: fix sleep in atomic context

This commit fixes the following error:
"BUG: sleeping function called from invalid context at kernel/irq/chip.c"

In DMA mode suppress the trigger irq handler, and make the buffer
transfers directly in DMA callback, instead.

Fixes: 2763ea0585c9 ("iio: adc: stm32: add optional dma support")
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Acked-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio:ad7797: Use correct attribute_group

It should use ad7797_attribute_group in ad7797_info,
according to commit ("iio:ad7793: Add support for the ad7796 and ad7797").

Scale is fixed for the ad7796 and not programmable, hence
should not have the scale_available attribute.

Fixes: fd1a8b912841 ("iio:ad7793: Add support for the ad7796 and ad7797")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

staging: vt6656: Use DIV_ROUND_UP macro instead of specific code

Use DIV_ROUND_UP macro instead of specific code with the same purpose.
Also, remove the unused variables.

Signed-off-by: Oscar Carter <oscar.carter@gmx.com>
Reviewed-by: Quentin Deslandes <quentin.deslandes@itdev.co.uk>
Link: https://lore.kernel.org/r/20200326175902.14467-1-oscar.carter@gmx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: remove hp100 driver

It's old, obsolete, and no one wants to take care of it anymore.

It's been in staging for 5 months with no one paying attention to it, so
let's just delete it for now.

If someone has this hardware, and wants the driver back, the deletion
can be easily reverted.

Cc: Joe Perches <joe@perches.com>
Cc: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20200326080233.978323-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: wilc1000: Use crc7 in lib/ rather than a private copy

The code in lib/ is the desired polynomial, and even includes
the 1-bit left shift in the table rather than needing to code
it explicitly.

While I'm in Kconfig, add a description of what a WILC1000 is.
Kconfig questions that require me to look up a data sheet to
find out that I probably don't have one are a pet peeve.

Cc: Adham Abozaeid <adham.abozaeid@microchip.com>
Cc: linux-wireless@vger.kernel.org
Reviewed-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: George Spelvin <lkml@sdf.org>
Link: https://lore.kernel.org/r/20200326152251.19094-1-ajay.kathat@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Staging: rtl8192u: ieee80211: Use netdev_alert().

Replace printk(KERN_ALERT ...) with netdev_alert()
when a network device is available.

Signed-off-by: Sam Muhammed <jane.pnx9@gmail.com>
Link: https://lore.kernel.org/r/70e8781cd2a9512cb6b3c42400a10323f3024f3c.1585233434.git.jane.pnx9@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Staging: rtl8192u: ieee80211: Use netdev_info() with network devices.

netdev_info() should be used instead of printk(KERN_INFO ...)
since it's specific to and preferable for printing messages
for network devices.

Signed-off-by: Sam Muhammed <jane.pnx9@gmail.com>
Link: https://lore.kernel.org/r/ce20980cc1947255b8a2de3c1f1364c11c163b9e.1585233434.git.jane.pnx9@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Staging: rtl8192u: ieee80211: Use netdev_warn() for network devices.

Use netdev_warn() over printk().
netdev_warn() is specific for printing warning
messages for network devices, and preferable
over printk(KERN_WARNING ...).

Signed-off-by: Sam Muhammed <jane.pnx9@gmail.com>
Link: https://lore.kernel.org/r/02fe0666cb737a3b0581081c9e7c179bfb820cac.1585233434.git.jane.pnx9@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Staging: rtl8192u: ieee80211: Use netdev_dbg() for debug messages.

Replace printk(KERN_DEBUG ...) with netdev_dbg() across the driver.
since netdev_dbg() is preferable and specific for
printing debug messages for network devices.

Signed-off-by: Sam Muhammed <jane.pnx9@gmail.com>
Link: https://lore.kernel.org/r/84dc7e33954509457efce2a35fb293e631845a96.1585233434.git.jane.pnx9@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: wlan-ng: fix use-after-free Read in hfa384x_usbin_callback

We can't handle the case length > WLAN_DATA_MAXLEN.
Because the size of rxfrm->data is WLAN_DATA_MAXLEN(2312), and we can't
read more than that.

Thanks-to: Hillf Danton <hdanton@sina.com>
Reported-and-tested-by: syzbot+7d42d68643a35f71ac8a@syzkaller.appspotmail.com
Signed-off-by: Qiujun Huang <hqjagain@gmail.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200326131850.17711-1-hqjagain@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8723bs: hal: Remove NULL check before kfree

NULL check before kfree is unnecessary so remove it.

The following Coccinelle script was used to detect this:
@@ expression E; @@
- if (E != NULL) { kfree(E); }
+ kfree(E);
@@ expression E; @@
- if (E != NULL) { kfree(E); E = NULL; }
+ kfree(E);
+ E = NULL;

Signed-off-by: Simran Singhal <singhalsimran0@gmail.com>
Link: https://lore.kernel.org/r/20200326132823.GA18625@simran-Inspiron-5558
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8723bs: hal: Correct typos in comments

Correct typos in comments.
Misspellings found using checkpatch.pl.

Signed-off-by: R Veera Kumar <vkor@vkten.in>
Link: https://lore.kernel.org/r/20200326143023.13681-1-vkor@vkten.in
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8723bs: os_dep: Correct typos in comments

Correct typos in comments.
Misspellings found using checkpatch.pl.

Signed-off-by: R Veera Kumar <vkor@vkten.in>
Link: https://lore.kernel.org/r/20200326125500.12861-1-vkor@vkten.in
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8723bs: core: Correct typos in comments

Correct typos in comments.
Misspellings found using checkpatch.pl.

Signed-off-by: R Veera Kumar <vkor@vkten.in>
Link: https://lore.kernel.org/r/20200326123540.12401-1-vkor@vkten.in
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8723bs: hal: Remove unnecessary cast on void pointer

Assignment to a typed pointer is sufficient in C.
No cast is needed.

The following Coccinelle script was used to detect this:
@r@
expression x;
void* e;
type T;
identifier f;
@@
(
  *((T *)e)
|
  ((T *)x)[...]
|
  ((T*)x)->f
|

- (T*)
  e
)

Signed-off-by: Simran Singhal <singhalsimran0@gmail.com>
Link: https://lore.kernel.org/r/20200326113210.GA29951@simran-Inspiron-5558
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8188eu: cleanup long line in odm.c

Cleanup line over 80 characters by removing unnecessary test
'pDM_Odm->RSSI_Min <= 25'. The above test 'pDM_Odm->RSSI_Min > 25'
already guarantees that it is <= 25.

Signed-off-by: Michael Straube <straube.linux@gmail.com>
Link: https://lore.kernel.org/r/20200326084348.15072-1-straube.linux@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8723bs: hal: Compress return logic

Simplify function returns by merging assignment and return into
one command line.
Found with Coccinelle

@@
local idexpression ret;
expression e;
@@

-ret =
+return
     e;
-return ret;

Signed-off-by: Simran Singhal <singhalsimran0@gmail.com>
Link: https://lore.kernel.org/r/20200325214312.GA1936@simran-Inspiron-5558
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8723bs: rtw_cmd: Compress lines for immediate return

Compress two lines into a single line if immediate return statement is found.
It also removes variable cmd_obj as it is no longer needed.

It is done using script Coccinelle.
And coccinelle uses following semantic patch for this compression function:

@@
expression ret;
identifier f;
@@

-ret =
+return
     f(...);
-return ret;

Signed-off-by: Simran Singhal <singhalsimran0@gmail.com>
Link: https://lore.kernel.org/r/20200325212253.GA8175@simran-Inspiron-5558
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8723bs: rtw_efuse: Compress lines for immediate return

Compress two lines into a single line if immediate return statement is found.

It is done using script Coccinelle. And coccinelle uses following semantic
patch for this compression function:

@@
expression ret;
identifier f;
@@

-ret =
+return
     f(...);
-return ret;

Signed-off-by: Simran Singhal <singhalsimran0@gmail.com>
Link: https://lore.kernel.org/r/20200325205418.GA29149@simran-Inspiron-5558
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: wilc1000: remove label from examples in DT binding documentation

Remove labels and not relevant property from DT binding documentation
examples as suggested in [1].

1. https://patchwork.ozlabs.org/patch/1252837

Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Link: https://lore.kernel.org/r/20200325164234.14146-1-ajay.kathat@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8723bs: Remove blank line before '}' brace

Remove unneeded blank line before a close brace '}'.
Issue found by checkpatch.pl:
CHECK: Blank lines aren't necessary before a close brace '}'

Signed-off-by: Simran Singhal <singhalsimran0@gmail.com>
Link: https://lore.kernel.org/r/20200325182617.GA9411@simran-Inspiron-5558
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Staging: rtl8188eu: hal: Add space around operators

Add space around operators for improving the code
readability.
Reported by checkpatch.pl

git diff -w shows no difference.
diff of the .o files before and after the changes shows no difference.

Signed-off-by: Shreeya Patel <shreeya.patel23498@gmail.com>
Link: https://lore.kernel.org/r/20200325160142.3698-1-shreeya.patel23498@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Staging: kpc2000: kpc_dma: Use spaces around operators.

Cleanup Checkpatch.pl CHECKs about missing
spaces around multiple operators.

Signed-off-by: Sam Muhammed <jane.pnx9@gmail.com>
Link: https://lore.kernel.org/r/22025abc8f8f3452c2d886e8faf1fe0532e8bb1d.1585143581.git.jane.pnx9@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Staging: kpc2000: kpc_dma: Use kcalloc over kzalloc.

Replace kzalloc(sizeof(...) * n, ...) with
kcalloc(n, sizeof(...), ...) since kcalloc is the
preferred API in case of allocating with multiply.

Checkpatch.pl: WARNING:
Prefer kcalloc over kzalloc with multiply.

Signed-off-by: Sam Muhammed <jane.pnx9@gmail.com>
Link: https://lore.kernel.org/r/4b8339d1e81e497c3c2f0dad57a9587338ec82b1.1585143581.git.jane.pnx9@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Staging: kpc2000: kpc_dma: Use the SPDK comment style.

SPDK-License-Identifier comment should have this form
// SPDX-License-Identifier: <GPL-...>

Signed-off-by: Sam Muhammed <jane.pnx9@gmail.com>
Link: https://lore.kernel.org/r/7531e3e3fa7c046e93d2caaa6fa2e76c5c53f04d.1585143581.git.jane.pnx9@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Staging: kpc2000: kpc_dma: Include the preferred header.

<linux/io.h> is the preferred header to include
instead of <asm/io.h>.

Checkpatch.pl WARNING:
Use #include <linux/io.h> instead of <asm/io.h>

Signed-off-by: Sam Muhammed <jane.pnx9@gmail.com>
Link: https://lore.kernel.org/r/c7a824c3a2ddc5f44bd89504b8c03a328d69f81d.1585143581.git.jane.pnx9@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Staging: kpc2000: kpc_dma: Remove unnecessary braces.

Remove braces of single statement blocks,
they are not really needed.

Signed-off-by: Sam Muhammed <jane.pnx9@gmail.com>
Link: https://lore.kernel.org/r/0a3ec63321dce008fc8dd790f42ef8490135b307.1585143581.git.jane.pnx9@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Staging: kpc2000: kpc_dma: Use sizeof(*var) in kzalloc().

kzalloc(sizeof(*var), ...) was the format been used
across the driver, which is the preferred format,
but missed two instances, correct them to match the
coding standards.

Checkpatch.pl CHECK: Prefer kzalloc(sizeof(*var)...)
over kzalloc(sizeof(struct var)...)

Signed-off-by: Sam Muhammed <jane.pnx9@gmail.com>
Link: https://lore.kernel.org/r/bbb3adbd20ae89db6a0d3360bc09d22eed778e86.1585143581.git.jane.pnx9@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Staging: kpc2000: kpc_dma: Remove comparison to NULL.

Comparison to NULL been used across the driver,
remove them and use (!var) instead.

Checkpatch.pl: CHECK:
Comparison to NULL could be written "!desc"... etc

Signed-off-by: Sam Muhammed <jane.pnx9@gmail.com>
Link: https://lore.kernel.org/r/f344afba0a8bb0413941a63678688435f04a96b4.1585143581.git.jane.pnx9@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: hp100: Properly indent the multiline comments.

Shift the end of multiline comments "*/" to the next line and align the
lines of the comments properly to improve code readability and to adhere
to the Linux Kernel coding style.
Reported by checkpatch.pl

Signed-off-by: Soumyajit Deb <debsoumyajit100@gmail.com>
Link: https://lore.kernel.org/r/20200325180003.46749-1-debsoumyajit100@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8723bs: Add line after variable declarations

Add whiteline after variable declarations to remove the checkpatch.pl
warning:
WARNING: Missing a blank line after declarations

Signed-off-by: Simran Singhal <singhalsimran0@gmail.com>
Link: https://lore.kernel.org/r/20200325164451.GA17569@simran-Inspiron-5558
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: hp100: Add space around operator

Add space around "-" operator to improve code readability and adhere to
the Linux kernel coding style.
Reported by checkpatch.pl

Signed-off-by: Soumyajit Deb <debsoumyajit100@gmail.com>
Link: https://lore.kernel.org/r/20200325144353.42655-1-debsoumyajit100@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8723bs: Remove multiple assignments

Remove multiple assignments by factorizing them.
Problem found using checkpatch.pl:-
CHECK: multiple assignments should be avoided

Signed-off-by: Simran Singhal <singhalsimran0@gmail.com>
Link: https://lore.kernel.org/r/20200325142226.GA14711@simran-Inspiron-5558
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8723bs: Remove unnecessary braces for single statements

Clean up unnecessary braces around single statement blocks.
Issues reported by checkpatch.pl as:
WARNING: braces {} are not necessary for single statement blocks

Signed-off-by: Simran Singhal <singhalsimran0@gmail.com>
Link: https://lore.kernel.org/r/20200325140245.GA11949@simran-Inspiron-5558
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: hp100: Add spaces in if statement.

Add space between if and open parenthesis to improve
code readability and to adhere to the standard linux kernel
coding style. Also, shift the next line to the right by a single space
as it is the continuation of the above if statement.

Signed-off-by: Soumyajit Deb <debsoumyajit100@gmail.com>
Link: https://lore.kernel.org/r/20200325122752.38600-1-debsoumyajit100@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: hp100: Add space between while keyword and open parenthesis

Add space between while keyword and open parenthesis "(" in the do while
statement to improve code readability and to adhere to the Linux Kernel
coding style.
Reported by checkpatch.pl

Signed-off-by: Soumyajit Deb <debsoumyajit100@gmail.com>
Link: https://lore.kernel.org/r/20200325115956.37126-1-debsoumyajit100@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: hp100: Remove space after opening parenthesis "("

Remove space after opening parenthesis in if statement to improve code
readability and to adhere to the standard coding style.
Reported by checkpatch.pl

Signed-off-by: Soumyajit Deb <debsoumyajit100@gmail.com>
Link: https://lore.kernel.org/r/20200325072905.29066-7-debsoumyajit100@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Staging: hp100: Add space after "," in function arguments.

Add space after "," in function arguments to improve code readability.
Reported by checkpatch.pl

Signed-off-by: Soumyajit Deb <debsoumyajit100@gmail.com>
Link: https://lore.kernel.org/r/20200325072905.29066-6-debsoumyajit100@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: hp100: Correct typo in the comment

Correct typo in the comment by changing "overriden" to "overridden".
Reported by checkpatch.pl

Signed-off-by: Soumyajit Deb <debsoumyajit100@gmail.com>
Link: https://lore.kernel.org/r/20200325072905.29066-4-debsoumyajit100@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: hp100: Remove extra blank lines

Remove extra blank lines from the code blocks.
Reported by checkpatch.pl

Signed-off-by: Soumyajit Deb <debsoumyajit100@gmail.com>
Link: https://lore.kernel.org/r/20200325035410.23802-1-debsoumyajit100@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: wlan-ng: fix ODEBUG bug in prism2sta_disconnect_usb

We should cancel hw->usb_work before kfree(hw).

Reported-by: syzbot+6d2e7f6fa90e27be9d62@syzkaller.appspotmail.com
Signed-off-by: Qiujun Huang <hqjagain@gmail.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1585120006-30042-1-git-send-email-hqjagain@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: vt6655: Break up function call with long line.

Update matches style found elsewhere in file.
Issue found by checkpatch: line over 80 characters.

Signed-off-by: Briana Oursler <briana.oursler@gmail.com>
Link: https://lore.kernel.org/r/20200324183812.79411-1-briana.oursler@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: most: Documentation: move ABI description files out of staging area

This patch moves the ABI description fils sysfs-bus-most and
configfs-most to the kernel's documentation folder.

Signed-off-by: Christian Gromm <christian.gromm@microchip.com>
Link: https://lore.kernel.org/r/1583845362-26707-4-git-send-email-christian.gromm@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: most: Documentation: update ABI description

This patch updates the ABI description files to be in sync
with current implementation.

Signed-off-by: Christian Gromm <christian.gromm@microchip.com>
Link: https://lore.kernel.org/r/1583845362-26707-3-git-send-email-christian.gromm@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: most: move core files out of the staging area

This patch moves the core module to the /drivers/most directory
and makes all necessary changes in order to not break the build.

Signed-off-by: Christian Gromm <christian.gromm@microchip.com>
Link: https://lore.kernel.org/r/1583845362-26707-2-git-send-email-christian.gromm@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Staging: speakup: Add identifier name to function declaration arguments.

void (*read_buff_add) argument didn't have an identifier name,
adding a name to it like the rest of all functions' arguments.

Signed-off-by: Sam Muhammed <jane.pnx9@gmail.com>
Reviewed-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Link: https://lore.kernel.org/r/b2a1ca962553194840d8cd2bf1f7d3174e3b1336.1585046066.git.jane.pnx9@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Staging: speakup: Use sizeof(*var) in kmalloc().

Modifying struct allocation in kmalloc() to match the
coding standards.

Checkpatch.pl CHECK: Prefer kmalloc(sizeof(*ldisc_data)...)
over kmalloc(sizeof(struct spk_ldisc_data)...)

Signed-off-by: Sam Muhammed <jane.pnx9@gmail.com>
Reviewed-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Link: https://lore.kernel.org/r/19494bdab5709693126e0c0ee14b179a3b601207.1585046066.git.jane.pnx9@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: comedi: ni_labpc_common: Reformat multiple line dereference

Reformat multi-line dereferencing of function arguments
&cmd->scan_begin_arg. Also reformat another call to the same function to
follow the same argument formatting structure. Problem detected by
checkpatch script.

Signed-off-by: Deepak R Varma <mh12gx2825@gmail.com>
Link: https://lore.kernel.org/r/20200322185932.GA12594@deeUbuntu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: hp100: Add space around operator +

Add space around operator + to improve code readability.
Reported by checkpatch.pl

Signed-off-by: Soumyajit Deb <debsoumyajit100@gmail.com>
Link: https://lore.kernel.org/r/20200323054836.48816-2-debsoumyajit100@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: iio: adc: ad7280a: Add comments to clarify stringified arguments

Checkpatch would flash a check message around a stringified macro
argument containing a '-' character. Add comment to indicate the
argument is legitimate and doesn't need fixing.

Signed-off-by: Deepak R Varma <mh12gx2825@gmail.com>
Suggested-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/469bf8db1c228913e72841367182fba2168fe795.1584904896.git.mh12gx2825@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: iio: adc: ad7192: Re-indent enum labels

Re-indent enum labels as per coding style guidelines. Problem
detected by checkpatch script.

Signed-off-by: Deepak R Varma <mh12gx2825@gmail.com>
Link: https://lore.kernel.org/r/5c6bef6462d135b748f58f8c2645c60234482f52.1584904896.git.mh12gx2825@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: wlan-ng: Fix third argument going over 80 characters

Create a new 'status' variable to store the value of a long argument
that goes over 80 characters. The status variable is also used for
an if check. Replacing that long statement in both places makes the
code much easier to read.

Note: the status variable is assigned after a needed byte order
conversion for usbin->rxfrm.desc.status, which uses a reference.

Issue reported by checkpatch.

Suggested-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: John B. Wyatt IV <jbwyatt4@gmail.com>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Link: https://lore.kernel.org/r/20200321225808.2494564-1-jbwyatt4@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Staging: speakup: Use pr_warn() defined in <linux/printk.h>.

Dropping a user-defined pr_warn() and using the kernel
message printing functions implemented in <linux/printk.h>.

Since both have the same functionality, using the standard
kernel functions is better.

Signed-off-by: Sam Muhammed <jane.pnx9@gmail.com>
Reviewed-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Link: https://lore.kernel.org/r/20200322143322.29098-1-jane.pnx9@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: greybus: tools: Fix braces {} style

This patch fixes the check reported by checkpatch.pl
for braces {} should be used on all arms of this statement.

Signed-off-by: Simran Singhal <singhalsimran0@gmail.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20200322173045.GA24700@simran-Inspiron-5558
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: mt7621-pci: avoid to set 'iomem_resource' addresses

Setting up kernel resource 'iomem_resource' for PCI with
addresses parsed from device tree gots into a conflict within
the usb xhci driver:

xhci-mtk 1e1c0000.xhci: can't request region for resource [mem 0x1e1c0000-0x1e1c0fff]
xhci-mtk: probe of 1e1c0000.xhci failed with error -16

Don't assign it and maintain the default addresses for this
resource seems to fix the problem. Checking legacy driver it
is being only  setting the 'ioport_resource'.

Fixes: 09dd629eeabb ("staging: mt7621-pci: fix io space and properly set resource limits")
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20200322072128.4454-1-sergio.paracuellos@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: hp100: Remove space after * in pointer declarations

Remove space after * in pointer declaration to improve code readability
and to adhere to the standard coding style.
Reported by checkpatch.pl

Signed-off-by: Soumyajit Deb <debsoumyajit100@gmail.com>
Link: https://lore.kernel.org/r/20200323054836.48816-3-debsoumyajit100@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Staging: hp: Use netdev_warn().

This replaces printk(KERN_WARNING ..) with netdev_warn(),
as the use of printk() isn't preferred when
a struct net_device is available.

Signed-off-by: Sam Muhammed <jane.pnx9@gmail.com>
Acked-by: Julia Lawall <julia.lawall@inria.fr>
Link: https://lore.kernel.org/r/20200322115051.2767-1-jane.pnx9@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8188eu: Add ASUS USB-N10 Nano B1 to device table

The ASUS USB-N10 Nano B1 has been reported as a new RTL8188EU device.
Add it to the device tables.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Reported-by: kovi <zraetn@gmail.com>
Cc: Stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200321180011.26153-1-Larry.Finger@lwfinger.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: mt7621-pci-phy: re-do 'xtal_mode' detection

Detection of the Xtal mode is using magic numbers that
can be avoided using properly some definitions and a more
accurate variable name from 'reg' into 'xtal_mode'. This
increase readability.

Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20200321133624.31388-4-sergio.paracuellos@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: mt7621-pci-phy: use builtin_platform_driver()

Macro builtin_platform_driver can be used for builtin drivers
that don't do anything in driver init. So, use the macro
builtin_platform_driver and remove some boilerplate code.

Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20200321133624.31388-3-sergio.paracuellos@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: mt7621-pci: use builtin_platform_driver()

Macro builtin_platform_driver can be used for builtin drivers
that don't do anything in driver init. So, use the macro
builtin_platform_driver and remove some boilerplate code.

Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20200321133624.31388-1-sergio.paracuellos@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge 5.6-rc7 into staging-next

We need the staging/iio fixes in here as well

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Linux 5.6-rc7

Merge tag 'for-5.6-rc6-tag' of git://git./linux/kernel/git/kdave/linux

Pull btrfs fixes from David Sterba:
 "Two fixes.

  The first is a regression: when dropping some incompat bits the
  conditions were reversed. The other is a fix for rename whiteout
  potentially leaving stack memory linked to a list"

* tag 'for-5.6-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
  btrfs: fix removal of raid[56|1c34} incompat flags after removing block group
  btrfs: fix log context list corruption after rename whiteout error

Merge branch 'akpm' (patches from Andrew)

Merge misc fixes from Andrew Morton:
 "10 fixes"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
  x86/mm: split vmalloc_sync_all()
  mm, slub: prevent kmalloc_node crashes and memory leaks
  mm/mmu_notifier: silence PROVE_RCU_LIST warnings
  epoll: fix possible lost wakeup on epoll_ctl() path
  mm: do not allow MADV_PAGEOUT for CoW pages
  mm, memcg: throttle allocators based on ancestral memory.high
  mm, memcg: fix corruption on 64-bit divisor in memory.high throttling
  page-flags: fix a crash at SetPageError(THP_SWAP)
  mm/hotplug: fix hot remove failure in SPARSEMEM|!VMEMMAP case
  memcg: fix NULL pointer dereference in __mem_cgroup_usage_unregister_event

x86/mm: split vmalloc_sync_all()

Commit 3f8fd02b1bf1 ("mm/vmalloc: Sync unmappings in
__purge_vmap_area_lazy()") introduced a call to vmalloc_sync_all() in
the vunmap() code-path.  While this change was necessary to maintain
correctness on x86-32-pae kernels, it also adds additional cycles for
architectures that don't need it.

Specifically on x86-64 with CONFIG_VMAP_STACK=y some people reported
severe performance regressions in micro-benchmarks because it now also
calls the x86-64 implementation of vmalloc_sync_all() on vunmap().  But
the vmalloc_sync_all() implementation on x86-64 is only needed for newly
created mappings.

To avoid the unnecessary work on x86-64 and to gain the performance
back, split up vmalloc_sync_all() into two functions:

* vmalloc_sync_mappings(), and
* vmalloc_sync_unmappings()

Most call-sites to vmalloc_sync_all() only care about new mappings being
synchronized.  The only exception is the new call-site added in the
above mentioned commit.

Shile Zhang directed us to a report of an 80% regression in reaim
throughput.

Fixes: 3f8fd02b1bf1 ("mm/vmalloc: Sync unmappings in __purge_vmap_area_lazy()")
Reported-by: kernel test robot <oliver.sang@intel.com>
Reported-by: Shile Zhang <shile.zhang@linux.alibaba.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Tested-by: Borislav Petkov <bp@suse.de>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> [GHES]
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: <stable@vger.kernel.org>
Link: http://lkml.kernel.org/r/20191009124418.8286-1-joro@8bytes.org
Link: https://lists.01.org/hyperkitty/list/lkp@lists.01.org/thread/4D3JPPHBNOSPFK2KEPC6KGKS6J25AIDB/
Link: http://lkml.kernel.org/r/20191113095530.228959-1-shile.zhang@linux.alibaba.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm, slub: prevent kmalloc_node crashes and memory leaks

Sachin reports [1] a crash in SLUB __slab_alloc():

  BUG: Kernel NULL pointer dereference on read at 0x000073b0
  Faulting instruction address: 0xc0000000003d55f4
  Oops: Kernel access of bad area, sig: 11 [#1]
  LE PAGE_SIZE=64K MMU=Hash SMP NR_CPUS=2048 NUMA pSeries
  Modules linked in:
  CPU: 19 PID: 1 Comm: systemd Not tainted 5.6.0-rc2-next-20200218-autotest #1
  NIP:  c0000000003d55f4 LR: c0000000003d5b94 CTR: 0000000000000000
  REGS: c0000008b37836d0 TRAP: 0300   Not tainted  (5.6.0-rc2-next-20200218-autotest)
  MSR:  8000000000009033 <SF,EE,ME,IR,DR,RI,LE>  CR: 24004844  XER: 00000000
  CFAR: c00000000000dec4 DAR: 00000000000073b0 DSISR: 40000000 IRQMASK: 1
  GPR00: c0000000003d5b94 c0000008b3783960 c00000000155d400 c0000008b301f500
  GPR04: 0000000000000dc0 0000000000000002 c0000000003443d8 c0000008bb398620
  GPR08: 00000008ba2f0000 0000000000000001 0000000000000000 0000000000000000
  GPR12: 0000000024004844 c00000001ec52a00 0000000000000000 0000000000000000
  GPR16: c0000008a1b20048 c000000001595898 c000000001750c18 0000000000000002
  GPR20: c000000001750c28 c000000001624470 0000000fffffffe0 5deadbeef0000122
  GPR24: 0000000000000001 0000000000000dc0 0000000000000002 c0000000003443d8
  GPR28: c0000008b301f500 c0000008bb398620 0000000000000000 c00c000002287180
  NIP ___slab_alloc+0x1f4/0x760
  LR __slab_alloc+0x34/0x60
  Call Trace:
    ___slab_alloc+0x334/0x760 (unreliable)
    __slab_alloc+0x34/0x60
    __kmalloc_node+0x110/0x490
    kvmalloc_node+0x58/0x110
    mem_cgroup_css_online+0x108/0x270
    online_css+0x48/0xd0
    cgroup_apply_control_enable+0x2ec/0x4d0
    cgroup_mkdir+0x228/0x5f0
    kernfs_iop_mkdir+0x90/0xf0
    vfs_mkdir+0x110/0x230
    do_mkdirat+0xb0/0x1a0
    system_call+0x5c/0x68

This is a PowerPC platform with following NUMA topology:

  available: 2 nodes (0-1)
  node 0 cpus:
  node 0 size: 0 MB
  node 0 free: 0 MB
  node 1 cpus: 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31
  node 1 size: 35247 MB
  node 1 free: 30907 MB
  node distances:
  node   0   1
    0:  10  40
    1:  40  10

  possible numa nodes: 0-31

This only happens with a mmotm patch "mm/memcontrol.c: allocate
shrinker_map on appropriate NUMA node" [2] which effectively calls
kmalloc_node for each possible node.  SLUB however only allocates
kmem_cache_node on online N_NORMAL_MEMORY nodes, and relies on
node_to_mem_node to return such valid node for other nodes since commit
a561ce00b09e ("slub: fall back to node_to_mem_node() node if allocating
on memoryless node").  This is however not true in this configuration
where the _node_numa_mem_ array is not initialized for nodes 0 and 2-31,
thus it contains zeroes and get_partial() ends up accessing
non-allocated kmem_cache_node.

A related issue was reported by Bharata (originally by Ramachandran) [3]
where a similar PowerPC configuration, but with mainline kernel without
patch [2] ends up allocating large amounts of pages by kmalloc-1k
kmalloc-512.  This seems to have the same underlying issue with
node_to_mem_node() not behaving as expected, and might probably also
lead to an infinite loop with CONFIG_SLUB_CPU_PARTIAL [4].

This patch should fix both issues by not relying on node_to_mem_node()
anymore and instead simply falling back to NUMA_NO_NODE, when
kmalloc_node(node) is attempted for a node that's not online, or has no
usable memory.  The "usable memory" condition is also changed from
node_present_pages() to N_NORMAL_MEMORY node state, as that is exactly
the condition that SLUB uses to allocate kmem_cache_node structures.
The check in get_partial() is removed completely, as the checks in
___slab_alloc() are now sufficient to prevent get_partial() being
reached with an invalid node.

[1] https://lore.kernel.org/linux-next/3381CD91-AB3D-4773-BA04-E7A072A63968@linux.vnet.ibm.com/
[2] https://lore.kernel.org/linux-mm/fff0e636-4c36-ed10-281c-8cdb0687c839@virtuozzo.com/
[3] https://lore.kernel.org/linux-mm/20200317092624.GB22538@in.ibm.com/
[4] https://lore.kernel.org/linux-mm/088b5996-faae-8a56-ef9c-5b567125ae54@suse.cz/

Fixes: a561ce00b09e ("slub: fall back to node_to_mem_node() node if allocating on memoryless node")
Reported-by: Sachin Sant <sachinp@linux.vnet.ibm.com>
Reported-by: PUVICHAKRAVARTHY RAMACHANDRAN <puvichakravarthy@in.ibm.com>
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Tested-by: Sachin Sant <sachinp@linux.vnet.ibm.com>
Tested-by: Bharata B Rao <bharata@linux.ibm.com>
Reviewed-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Christopher Lameter <cl@linux.com>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Kirill Tkhai <ktkhai@virtuozzo.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Nathan Lynch <nathanl@linux.ibm.com>
Cc: <stable@vger.kernel.org>
Link: http://lkml.kernel.org/r/20200320115533.9604-1-vbabka@suse.cz
Debugged-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm/mmu_notifier: silence PROVE_RCU_LIST warnings

It is safe to traverse mm->notifier_subscriptions->list either under
SRCU read lock or mm->notifier_subscriptions->lock using
hlist_for_each_entry_rcu().  Silence the PROVE_RCU_LIST false positives,
for example,

  WARNING: suspicious RCU usage
  -----------------------------
  mm/mmu_notifier.c:484 RCU-list traversed in non-reader section!!

  other info that might help us debug this:

  rcu_scheduler_active = 2, debug_locks = 1
  3 locks held by libvirtd/802:
   #0: ffff9321e3f58148 (&mm->mmap_sem#2){++++}, at: do_mprotect_pkey+0xe1/0x3e0
   #1: ffffffff91ae6160 (mmu_notifier_invalidate_range_start){+.+.}, at: change_p4d_range+0x5fa/0x800
   #2: ffffffff91ae6e08 (srcu){....}, at: __mmu_notifier_invalidate_range_start+0x178/0x460

  stack backtrace:
  CPU: 7 PID: 802 Comm: libvirtd Tainted: G          I       5.6.0-rc6-next-20200317+ #2
  Hardware name: HP ProLiant BL460c Gen8, BIOS I31 11/02/2014
  Call Trace:
    dump_stack+0xa4/0xfe
    lockdep_rcu_suspicious+0xeb/0xf5
    __mmu_notifier_invalidate_range_start+0x3ff/0x460
    change_p4d_range+0x746/0x800
    change_protection+0x1df/0x300
    mprotect_fixup+0x245/0x3e0
    do_mprotect_pkey+0x23b/0x3e0
    __x64_sys_mprotect+0x51/0x70
    do_syscall_64+0x91/0xae8
    entry_SYSCALL_64_after_hwframe+0x49/0xb3

Signed-off-by: Qian Cai <cai@lca.pw>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Paul E. McKenney <paulmck@kernel.org>
Reviewed-by: Jason Gunthorpe <jgg@mellanox.com>
Link: http://lkml.kernel.org/r/20200317175640.2047-1-cai@lca.pw
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

epoll: fix possible lost wakeup on epoll_ctl() path

This fixes possible lost wakeup introduced by commit a218cc491420.
Originally modifications to ep->wq were serialized by ep->wq.lock, but
in commit a218cc491420 ("epoll: use rwlock in order to reduce
ep_poll_callback() contention") a new rw lock was introduced in order to
relax fd event path, i.e. callers of ep_poll_callback() function.

After the change ep_modify and ep_insert (both are called on epoll_ctl()
path) were switched to ep->lock, but ep_poll (epoll_wait) was using
ep->wq.lock on wqueue list modification.

The bug doesn't lead to any wqueue list corruptions, because wake up
path and list modifications were serialized by ep->wq.lock internally,
but actual waitqueue_active() check prior wake_up() call can be
reordered with modifications of ep ready list, thus wake up can be lost.

And yes, can be healed by explicit smp_mb():

  list_add_tail(&epi->rdlink, &ep->rdllist);
  smp_mb();
  if (waitqueue_active(&ep->wq))
wake_up(&ep->wp);

But let's make it simple, thus current patch replaces ep->wq.lock with
the ep->lock for wqueue modifications, thus wake up path always observes
activeness of the wqueue correcty.

Fixes: a218cc491420 ("epoll: use rwlock in order to reduce ep_poll_callback() contention")
Reported-by: Max Neunhoeffer <max@arangodb.com>
Signed-off-by: Roman Penyaev <rpenyaev@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Tested-by: Max Neunhoeffer <max@arangodb.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Christopher Kohlhoff <chris.kohlhoff@clearpool.io>
Cc: Davidlohr Bueso <dbueso@suse.de>
Cc: Jason Baron <jbaron@akamai.com>
Cc: Jes Sorensen <jes.sorensen@gmail.com>
Cc: <stable@vger.kernel.org> [5.1+]
Link: http://lkml.kernel.org/r/20200214170211.561524-1-rpenyaev@suse.de
References: https://bugzilla.kernel.org/show_bug.cgi?id=205933
Bisected-by: Max Neunhoeffer <max@arangodb.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm: do not allow MADV_PAGEOUT for CoW pages

Jann has brought up a very interesting point [1].  While shared pages
are excluded from MADV_PAGEOUT normally, CoW pages can be easily
reclaimed that way.  This can lead to all sorts of hard to debug
problems.  E.g.  performance problems outlined by Daniel [2].

There are runtime environments where there is a substantial memory
shared among security domains via CoW memory and a easy to reclaim way
of that memory, which MADV_{COLD,PAGEOUT} offers, can lead to either
performance degradation in for the parent process which might be more
privileged or even open side channel attacks.

The feasibility of the latter is not really clear to me TBH but there is
no real reason for exposure at this stage.  It seems there is no real
use case to depend on reclaiming CoW memory via madvise at this stage so
it is much easier to simply disallow it and this is what this patch
does.  Put it simply MADV_{PAGEOUT,COLD} can operate only on the
exclusively owned memory which is a straightforward semantic.

[1] http://lkml.kernel.org/r/CAG48ez0G3JkMq61gUmyQAaCq=_TwHbi1XKzWRooxZkv08PQKuw@mail.gmail.com
[2] http://lkml.kernel.org/r/CAKOZueua_v8jHCpmEtTB6f3i9e2YnmX4mqdYVWhV4E=Z-n+zRQ@mail.gmail.com

Fixes: 9c276cc65a58 ("mm: introduce MADV_COLD")
Reported-by: Jann Horn <jannh@google.com>
Signed-off-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Daniel Colascione <dancol@google.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: "Joel Fernandes (Google)" <joel@joelfernandes.org>
Cc: <stable@vger.kernel.org>
Link: http://lkml.kernel.org/r/20200312082248.GS23944@dhcp22.suse.cz
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm, memcg: throttle allocators based on ancestral memory.high

Prior to this commit, we only directly check the affected cgroup's
memory.high against its usage.  However, it's possible that we are being
reclaimed as a result of hitting an ancestor memory.high and should be
penalised based on that, instead.

This patch changes memory.high overage throttling to use the largest
overage in its ancestors when considering how many penalty jiffies to
charge.  This makes sure that we penalise poorly behaving cgroups in the
same way regardless of at what level of the hierarchy memory.high was
breached.

Fixes: 0e4b01df8659 ("mm, memcg: throttle allocators when failing reclaim over memory.high")
Reported-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Chris Down <chris@chrisdown.name>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Nathan Chancellor <natechancellor@gmail.com>
Cc: Roman Gushchin <guro@fb.com>
Cc: <stable@vger.kernel.org> [5.4.x+]
Link: http://lkml.kernel.org/r/8cd132f84bd7e16cdb8fde3378cdbf05ba00d387.1584036142.git.chris@chrisdown.name
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm, memcg: fix corruption on 64-bit divisor in memory.high throttling

Commit 0e4b01df8659 had a bunch of fixups to use the right division
method.  However, it seems that after all that it still wasn't right --
div_u64 takes a 32-bit divisor.

The headroom is still large (2^32 pages), so on mundane systems you
won't hit this, but this should definitely be fixed.

Fixes: 0e4b01df8659 ("mm, memcg: throttle allocators when failing reclaim over memory.high")
Reported-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Chris Down <chris@chrisdown.name>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Roman Gushchin <guro@fb.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Nathan Chancellor <natechancellor@gmail.com>
Cc: <stable@vger.kernel.org> [5.4.x+]
Link: http://lkml.kernel.org/r/80780887060514967d414b3cd91f9a316a16ab98.1584036142.git.chris@chrisdown.name
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

page-flags: fix a crash at SetPageError(THP_SWAP)

Commit bd4c82c22c36 ("mm, THP, swap: delay splitting THP after swapped
out") supported writing THP to a swap device but forgot to upgrade an
older commit df8c94d13c7e ("page-flags: define behavior of FS/IO-related
flags on compound pages") which could trigger a crash during THP
swapping out with DEBUG_VM_PGFLAGS=y,

  kernel BUG at include/linux/page-flags.h:317!

  page dumped because: VM_BUG_ON_PAGE(1 && PageCompound(page))
  page:fffff3b2ec3a8000 refcount:512 mapcount:0 mapping:000000009eb0338c index:0x7f6e58200 head:fffff3b2ec3a8000 order:9 compound_mapcount:0 compound_pincount:0
  anon flags: 0x45fffe0000d8454(uptodate|lru|workingset|owner_priv_1|writeback|head|reclaim|swapbacked)

  end_swap_bio_write()
    SetPageError(page)
      VM_BUG_ON_PAGE(1 && PageCompound(page))

  <IRQ>
  bio_endio+0x297/0x560
  dec_pending+0x218/0x430 [dm_mod]
  clone_endio+0xe4/0x2c0 [dm_mod]
  bio_endio+0x297/0x560
  blk_update_request+0x201/0x920
  scsi_end_request+0x6b/0x4b0
  scsi_io_completion+0x509/0x7e0
  scsi_finish_command+0x1ed/0x2a0
  scsi_softirq_done+0x1c9/0x1d0
  __blk_mqnterrupt+0xf/0x20
  </IRQ>

Fix by checking PF_NO_TAIL in those places instead.

Fixes: bd4c82c22c36 ("mm, THP, swap: delay splitting THP after swapped out")
Signed-off-by: Qian Cai <cai@lca.pw>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: David Hildenbrand <david@redhat.com>
Acked-by: "Huang, Ying" <ying.huang@intel.com>
Acked-by: Rafael Aquini <aquini@redhat.com>
Cc: <stable@vger.kernel.org>
Link: http://lkml.kernel.org/r/20200310235846.1319-1-cai@lca.pw
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm/hotplug: fix hot remove failure in SPARSEMEM|!VMEMMAP case

In section_deactivate(), pfn_to_page() doesn't work any more after
ms->section_mem_map is resetting to NULL in SPARSEMEM|!VMEMMAP case.  It
causes a hot remove failure:

  kernel BUG at mm/page_alloc.c:4806!
  invalid opcode: 0000 [#1] SMP PTI
  CPU: 3 PID: 8 Comm: kworker/u16:0 Tainted: G        W         5.5.0-next-20200205+ #340
  Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 0.0.0 02/06/2015
  Workqueue: kacpi_hotplug acpi_hotplug_work_fn
  RIP: 0010:free_pages+0x85/0xa0
  Call Trace:
   __remove_pages+0x99/0xc0
   arch_remove_memory+0x23/0x4d
   try_remove_memory+0xc8/0x130
   __remove_memory+0xa/0x11
   acpi_memory_device_remove+0x72/0x100
   acpi_bus_trim+0x55/0x90
   acpi_device_hotplug+0x2eb/0x3d0
   acpi_hotplug_work_fn+0x1a/0x30
   process_one_work+0x1a7/0x370
   worker_thread+0x30/0x380
   kthread+0x112/0x130
   ret_from_fork+0x35/0x40

Let's move the ->section_mem_map resetting after
depopulate_section_memmap() to fix it.

[akpm@linux-foundation.org: remove unneeded initialization, per David]
Fixes: ba72b4c8cf60 ("mm/sparsemem: support sub-section hotplug")
Signed-off-by: Baoquan He <bhe@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Pankaj Gupta <pankaj.gupta.linux@gmail.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Wei Yang <richardw.yang@linux.intel.com>
Cc: Oscar Salvador <osalvador@suse.de>
Cc: Mike Rapoport <rppt@linux.ibm.com>
Cc: <stable@vger.kernel.org>
Link: http://lkml.kernel.org/r/20200307084229.28251-2-bhe@redhat.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

memcg: fix NULL pointer dereference in __mem_cgroup_usage_unregister_event

An eventfd monitors multiple memory thresholds of the cgroup, closes them,
the kernel deletes all events related to this eventfd.  Before all events
are deleted, another eventfd monitors the memory threshold of this cgroup,
leading to a crash:

  BUG: kernel NULL pointer dereference, address: 0000000000000004
  #PF: supervisor write access in kernel mode
  #PF: error_code(0x0002) - not-present page
  PGD 800000033058e067 P4D 800000033058e067 PUD 3355ce067 PMD 0
  Oops: 0002 [#1] SMP PTI
  CPU: 2 PID: 14012 Comm: kworker/2:6 Kdump: loaded Not tainted 5.6.0-rc4 #3
  Hardware name: LENOVO 20AWS01K00/20AWS01K00, BIOS GLET70WW (2.24 ) 05/21/2014
  Workqueue: events memcg_event_remove
  RIP: 0010:__mem_cgroup_usage_unregister_event+0xb3/0x190
  RSP: 0018:ffffb47e01c4fe18 EFLAGS: 00010202
  RAX: 0000000000000001 RBX: ffff8bb223a8a000 RCX: 0000000000000001
  RDX: 0000000000000001 RSI: ffff8bb22fb83540 RDI: 0000000000000001
  RBP: ffffb47e01c4fe48 R08: 0000000000000000 R09: 0000000000000010
  R10: 000000000000000c R11: 071c71c71c71c71c R12: ffff8bb226aba880
  R13: ffff8bb223a8a480 R14: 0000000000000000 R15: 0000000000000000
  FS:  0000000000000000(0000) GS:ffff8bb242680000(0000) knlGS:0000000000000000
  CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
  CR2: 0000000000000004 CR3: 000000032c29c003 CR4: 00000000001606e0
  Call Trace:
    memcg_event_remove+0x32/0x90
    process_one_work+0x172/0x380
    worker_thread+0x49/0x3f0
    kthread+0xf8/0x130
    ret_from_fork+0x35/0x40
  CR2: 0000000000000004

We can reproduce this problem in the following ways:

1. We create a new cgroup subdirectory and a new eventfd, and then we
   monitor multiple memory thresholds of the cgroup through this eventfd.

2.  closing this eventfd, and __mem_cgroup_usage_unregister_event ()
   will be called multiple times to delete all events related to this
   eventfd.

The first time __mem_cgroup_usage_unregister_event() is called, the
kernel will clear all items related to this eventfd in thresholds->
primary.

Since there is currently only one eventfd, thresholds-> primary becomes
empty, so the kernel will set thresholds-> primary and hresholds-> spare
to NULL.  If at this time, the user creates a new eventfd and monitor
the memory threshold of this cgroup, kernel will re-initialize
thresholds-> primary.

Then when __mem_cgroup_usage_unregister_event () is called for the
second time, because thresholds-> primary is not empty, the system will
access thresholds-> spare, but thresholds-> spare is NULL, which will
trigger a crash.

In general, the longer it takes to delete all events related to this
eventfd, the easier it is to trigger this problem.

The solution is to check whether the thresholds associated with the
eventfd has been cleared when deleting the event.  If so, we do nothing.

[akpm@linux-foundation.org: fix comment, per Kirill]
Fixes: 907860ed381a ("cgroups: make cftype.unregister_event() void-returning")
Signed-off-by: Chunguang Xu <brookxu@tencent.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Vladimir Davydov <vdavydov.dev@gmail.com>
Cc: <stable@vger.kernel.org>
Link: http://lkml.kernel.org/r/077a6f67-aefa-4591-efec-f2f3af2b0b02@gmail.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge tag 'block-5.6-20200320' of git://git.kernel.dk/linux-block

Pull block fixes from Jens Axboe:
 "Just two NVMe fabrics fixes that should go into 5.6"

* tag 'block-5.6-20200320' of git://git.kernel.dk/linux-block:
  nvmet-tcp: set MSG_MORE only if we actually have more to send
  nvme-rdma: Avoid double freeing of async event data

Merge tag 'io_uring-5.6-20200320' of git://git.kernel.dk/linux-block

Pull io_uring fixes from Jens Axboe:
 "Two different fixes in here:

   - Fix for a potential NULL pointer deref for links with async or
     drain marked (Pavel)

   - Fix for not properly checking RLIMIT_NOFILE for async punted
     operations.

     This affects openat/openat2, which were added this cycle, and
     accept4. I did a full audit of other cases where we might check
     current->signal->rlim[] and found only RLIMIT_FSIZE for buffered
     writes and fallocate. That one is fixed and queued for 5.7 and
     marked stable"

* tag 'io_uring-5.6-20200320' of git://git.kernel.dk/linux-block:
  io_uring: make sure accept honor rlimit nofile
  io_uring: make sure openat/openat2 honor rlimit nofile
  io_uring: NULL-deref for IOSQE_{ASYNC,DRAIN}

Merge branch 'turbostat' of git://git./linux/kernel/git/lenb/linux

Pull turbostat updates from Len Brown:
 "Update to turbostat v20.03.20.

  These patches unlock the full turbostat features for some new
  machines, plus a couple other minor tweaks"

* 'turbostat' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
  tools/power turbostat: update version
  tools/power turbostat: Print cpuidle information
  tools/power turbostat: Fix 32-bit capabilities warning
  tools/power turbostat: Fix missing SYS_LPI counter on some Chromebooks
  tools/power turbostat: Support Elkhart Lake
  tools/power turbostat: Support Jasper Lake
  tools/power turbostat: Support Ice Lake server
  tools/power turbostat: Support Tiger Lake
  tools/power turbostat: Fix gcc build warnings
  tools/power turbostat: Support Cometlake

Merge tag 'powerpc-5.6-5' of git://git./linux/kernel/git/powerpc/linux

Pull powerpc fixes from Michael Ellerman:
 "Two fixes for bugs introduced this cycle:

   - fix a crash when shutting down a KVM PR guest (our original style
     of KVM which doesn't use hypervisor mode)

   - fix for the recently added 32-bit KASAN_VMALLOC support

  Thanks to: Christophe Leroy, Greg Kurz, Sean Christopherson"

* tag 'powerpc-5.6-5' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  KVM: PPC: Fix kernel crash with PR KVM
  powerpc/kasan: Fix shadow memory protection with CONFIG_KASAN_VMALLOC

staging: vt6656: Use BIT() macro in vnt_mac_reg_bits_* functions

The last parameter in the functions vnt_mac_reg_bits_on and
vnt_mac_reg_bits_off defines the bits to set or unset. So, it's more
clear to use the BIT() macro instead of an hexadecimal value.

Signed-off-by: Oscar Carter <oscar.carter@gmx.com>
Link: https://lore.kernel.org/r/20200320181326.12156-1-oscar.carter@gmx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8188eu: remove some 5 GHz code

According to the TODO code valid only for 5 GHz should be removed.

- find and remove remaining code valid only for 5 GHz. Most of the obvious
  ones have been removed, but things like channel > 14 still exist.

Remove if statement that checks for channel > 14 from rtw_ieee80211.c.

Signed-off-by: Michael Straube <straube.linux@gmail.com>
Link: https://lore.kernel.org/r/20200320191305.10425-1-straube.linux@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: vt6656: Use BIT() macro instead of hex value

Use the BIT() macro instead of the hexadecimal value to define the
different bits in registers.

Signed-off-by: Oscar Carter <oscar.carter@gmx.com>
Link: https://lore.kernel.org/r/20200320171056.7841-1-oscar.carter@gmx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8723bs: os_dep: Remove whitespace characters in code line

Remove four leading whitespace characters in code line.

Signed-off-by: R Veera Kumar <vkor@vkten.in>
Link: https://lore.kernel.org/r/27b60d20868203efdc5975803f5f9d43e46526dd.1584764104.git.vkor@vkten.in
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8723bs: os_dep: Correct long line comments

Correct long line comments to respect 80 character per
line limit.

Signed-off-by: R Veera Kumar <vkor@vkten.in>
Link: https://lore.kernel.org/r/16399fc057c6dd1c78e77ddd3b3224f4b2e37da5.1584764104.git.vkor@vkten.in
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8723bs: os_dep: Remove commented out code lines

Remove multiple commented out code lines.
Remove blank lines next to them.

Signed-off-by: R Veera Kumar <vkor@vkten.in>
Link: https://lore.kernel.org/r/a62d2fbb77990210b939a5ec99ee27cfa5749a09.1584764104.git.vkor@vkten.in
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8723bs: remove unneeded variables

Remove unneeded temporary local variables and their declarations.

Signed-off-by: Payal Kshirsagar <payalskshirsagar1234@gmail.com>
Link: https://lore.kernel.org/r/20200321074757.8321-1-payalskshirsagar1234@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: mt7621-pci: delete release gpios related code

Making gpio8 and gpio9 vendor specific and putting them
into the specific dts file makes not needed to release
gpios anymore because we are not occupying those pins
in the first place if it is not necessary. When the
device tree is parsed we can also check and return for
the error because we rely in the fact that the related
device for the board is correct.

Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20200321072650.7784-3-sergio.paracuellos@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>