Dave Stevenson [Wed, 15 Feb 2023 22:29:57 +0000 (23:29 +0100)]
media: i2c: imx290: Convert V4L2_CID_HBLANK to read/write
The driver exposed V4L2_CID_HBLANK as a read only control to allow
for exposure calculations and determination of the frame rate.
Convert to a read/write control so that the frame rate can be
controlled.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Dave Stevenson [Wed, 15 Feb 2023 22:29:56 +0000 (23:29 +0100)]
media: i2c: imx290: Use CSI timings as per datasheet
Commit "
98e0500eadb7 media: i2c: imx290: Add configurable link frequency
and pixel rate" added support for the increased link frequencies
on 2 data lanes, but didn't update the CSI timing registers in
accordance with the datasheet.
Use the specified settings.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Dave Stevenson [Wed, 15 Feb 2023 22:29:55 +0000 (23:29 +0100)]
media: i2c: imx290: Support 60fps in 2 lane operation
Commit "
97589ad61c73 media: i2c: imx290: Add support for 2 data lanes"
added support for running in two lane mode (instead of 4), but
without changing the link frequency that resulted in a max of 30fps.
Commit "
98e0500eadb7 media: i2c: imx290: Add configurable link frequency
and pixel rate" then doubled the link frequency when in 2 lane mode,
but didn't undo the correction for running at only 30fps, just extending
horizontal blanking instead.
Remove the 30fps limit on 2 lane by correcting the register config
in accordance with the datasheet for 60fps operation over 2 lanes.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Dave Stevenson [Wed, 15 Feb 2023 22:29:54 +0000 (23:29 +0100)]
media: i2c: imx290: Fix the pixel rate at 148.5Mpix/s
The datasheet lists the link frequency changes between
1080p and 720p modes. This is correct that the link frequency
changes as measured on an oscilloscope.
Link frequency is not necessarily the same as pixel rate.
The datasheet gives standard configurations for 1080p and 720p
modes at a number of frame rates.
Looking at the 1080p mode it gives:
HMAX = 0x898 = 2200
VMAX = 0x465 = 1125
2200 * 1125 * 60fps = 148.5MPix/s
Looking at the 720p mode it gives:
HMAX = 0xce4 = 3300
VMAX = 0x2ee = 750
3300 * 750 * 60fps = 148.5Mpix/s
This driver currently scales the pixel rate proportionally to the
link frequency, however the above shows that this is not the
correct thing to do, and currently all frame rate and exposure
calculations give incorrect results.
Correctly report the pixel rate as being 148.5MPix/s under any
mode.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Dave Stevenson [Wed, 15 Feb 2023 22:29:53 +0000 (23:29 +0100)]
media: i2c: imx290: Add V4L2_SUBDEV_FL_HAS_EVENTS and subscribe hooks
Any V4L2 subdevice that implements controls and declares
V4L2_SUBDEV_FL_HAS_DEVNODE should also declare V4L2_SUBDEV_FL_HAS_EVENTS
and implement subscribe_event and unsubscribe_event hooks.
This driver didn't and would therefore fail v4l2-compliance
testing.
Add the relevant hooks.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Dave Stevenson [Wed, 15 Feb 2023 22:29:52 +0000 (23:29 +0100)]
media: i2c: imx290: Set the colorspace fields in the format
The colorspace fields were left untouched in imx290_set_fmt
which lead to a v4l2-compliance failure.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Dave Stevenson [Wed, 15 Feb 2023 22:29:51 +0000 (23:29 +0100)]
media: i2c: imx290: Match kernel coding style on whitespace
Fix up a couple of coding style issues regarding missing blank
lines after declarations, double blank lines, and incorrect
indentation.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Dave Stevenson [Wed, 15 Feb 2023 22:29:50 +0000 (23:29 +0100)]
media: i2c: imx290: Add support for the mono sensor variant
The IMX290 module is available as either mono or colour (Bayer).
Update the driver so that it can advertise the correct mono
formats instead of the colour ones.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Dave Stevenson [Wed, 15 Feb 2023 22:29:49 +0000 (23:29 +0100)]
media: dt-bindings: media: i2c: Add mono version to IMX290 bindings
The IMX290 module is available as either monochrome or colour and
the variant is not detectable at runtime.
Add a new compatible string for the monochrome version, based on the
full device name IMX290LLR. For consistency, add a new compatible string
for the colour version based on the IMX290LQR full device name, and
deprecate the current ambiguous compatible string.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Jacopo Mondi [Tue, 21 Feb 2023 17:10:48 +0000 (18:10 +0100)]
media: i2c: ov5647: Use bus-locked i2c_transfer()
The ov5647_read() functions calls i2c_master_send() and
i2c_master_read() in sequence. However this leaves space for other
clients to contend the bus and insert an unrelated transaction in between
the two calls.
Replace the two calls with a single i2c_transfer() one, that locks the
bus in between the transactions.
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Tommaso Merciai <tomm.merciai@gmail.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Valentine Barshak [Tue, 21 Feb 2023 17:10:47 +0000 (18:10 +0100)]
media: i2c: ov5647: Add test pattern control
This adds V4L2_CID_TEST_PATTERN control support.
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Tommaso Merciai <tomm.merciai@gmail.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Andy Shevchenko [Thu, 9 Feb 2023 22:09:54 +0000 (23:09 +0100)]
media: i2c: imx290: Use device_property_read_u32() directly
No need to call fwnode_property_read_u32(dev_fwnode()), when
we have already existing helper. So use it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Andy Shevchenko [Thu, 9 Feb 2023 22:12:05 +0000 (23:12 +0100)]
media: i2c: imx290: Make use of get_unaligned_le24(), put_unaligned_le24()
Since we have a proper endianness converters for LE 24-bit data use them.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Tomi Valkeinen [Thu, 2 Mar 2023 09:57:48 +0000 (10:57 +0100)]
media: subdev: Add V4L2_SUBDEV_ROUTING_NO_MULTIPLEXING
A common case with subdev routing is that on the subdevice just before
the DMA engines (video nodes), no multiplexing is allowed on the source
pads, as the DMA engine can only handle a single stream.
In some other situations one might also want to do the same check on the
sink side.
Add new routing validation flags to check these:
V4L2_SUBDEV_ROUTING_NO_SINK_MULTIPLEXING and
V4L2_SUBDEV_ROUTING_NO_SOURCE_MULTIPLEXING.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Tomi Valkeinen [Thu, 2 Mar 2023 09:57:47 +0000 (10:57 +0100)]
media: subdev: Split V4L2_SUBDEV_ROUTING_NO_STREAM_MIX
V4L2_SUBDEV_ROUTING_NO_STREAM_MIX routing validation flag means that all
routes from a sink pad must go to the same source pad and all routes
going to the same source pad must originate from the same sink pad.
This does not cover all use cases. For example, if a device routes
all streams from a single sink pad to any of the source pads, but
streams from multiple sink pads can go to the same source pad, the
current flag is too restrictive.
Split the flag into two parts, V4L2_SUBDEV_ROUTING_NO_SINK_STREAM_MIX
and V4L2_SUBDEV_ROUTING_NO_SOURCE_STREAM_MIX, which add the restriction
only on one side of the device. Together they mean the same as
V4L2_SUBDEV_ROUTING_NO_STREAM_MIX.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Tomi Valkeinen [Thu, 2 Mar 2023 09:57:46 +0000 (10:57 +0100)]
media: subdev: Use 'shall' instead of 'may' in route validation
Route validation docs use the word 'may'. Change that to 'shall' for
emphasis.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Benjamin Mugnier [Wed, 1 Feb 2023 14:04:17 +0000 (15:04 +0100)]
media: i2c: st-vgxy61: Use VGXY61_NB_POLARITIES instead of hardcoded value in tx_from_ep
tx_from_ep's for loop uses '5' as bound, while in fact it refers to the
number of polarities. Replace it by VGXY61_NB_POLARITIES for
factorization.
Signed-off-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Benjamin Mugnier [Wed, 1 Feb 2023 14:04:16 +0000 (15:04 +0100)]
media: i2c: st-vgxy61: Fix control flow error on probe
In case of error 'update_hdr' now goes through 'power_off' instead of
returning, effectively shutting down the sensor.
Signed-off-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Benjamin Mugnier [Wed, 1 Feb 2023 14:04:15 +0000 (15:04 +0100)]
media: i2c: st-vgxy61: Move 'detect' call to 'power_on'
Previously the device detection was performed after patching.
Move it right after the reset to make sure we have the correct sensor
before trying to patch it.
Signed-off-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Benjamin Mugnier [Wed, 1 Feb 2023 14:04:14 +0000 (15:04 +0100)]
media: i2c: st-vgxy61: Remove duplicate default mode set on probe
At this stage the default mode is unknown.
This is done correctly by vgxy61_fill_framefmt right after.
Signed-off-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Hans Verkuil [Thu, 2 Mar 2023 12:57:31 +0000 (13:57 +0100)]
media: Documentation: userspace-api: media: drop clipping, destructive overlays
Support for clipping for overlays has been removed, update the
documentation.
Support for destructive overlay support has been removed as well,
also update the documentation for this.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Hans Verkuil [Thu, 2 Mar 2023 12:57:30 +0000 (13:57 +0100)]
media: v4l2-core: zero field base in struct v4l2_framebuffer
Make sure this field is always 0 since destructive overlays
are no longer supported.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Hans Verkuil [Thu, 2 Mar 2023 12:57:29 +0000 (13:57 +0100)]
media: videodev.h: drop V4L2_FBUF_CAP_LIST/BITMAP_CLIPPING
These two capabilities are no longer supported, so no
longer define them when compiling the kernel.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Hans Verkuil [Thu, 2 Mar 2023 12:57:28 +0000 (13:57 +0100)]
media: v4l2-core: drop v4l2_window clipping and bitmap support
There are no longer any drivers that support clipping and bitmap
support for the capture or output overlay interfaces, so drop
this.
Always set the bitmap, clips and clipcount fields to 0, and
remove the compat32 support.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Hans Verkuil [Thu, 2 Mar 2023 12:57:27 +0000 (13:57 +0100)]
media: vivid: drop bitmap and clipping output overlay support
This test driver is the only remaining driver still using
the clipping and bitmap method. Drop support for this so
we can remove this in the V4L2 API as well.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Hans Verkuil [Thu, 2 Mar 2023 12:57:26 +0000 (13:57 +0100)]
media: vivid: drop overlay support
Destructive overlay support (i.e. where the video frame is DMA-ed
straight into a framebuffer) is effectively dead. It was a
necessary evil in the early days when computers were not fast enough
to copy SDTV video frames around, but today that's no longer a problem.
It requires access to the framebuffer memory, which is a bad idea and
very hard to do safely. In addition, in drm it is today almost
impossible to get hold of the framebuffer address.
So drop support for this.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Hans Verkuil [Thu, 2 Mar 2023 12:57:25 +0000 (13:57 +0100)]
media: bttv: drop overlay support
Destructive overlay support (i.e. where the video frame is DMA-ed
straight into a framebuffer) is effectively dead. It was a
necessary evil in the early days when computers were not fast enough
to copy SDTV video frames around, but today that's no longer a problem.
It requires access to the framebuffer memory, which is a bad idea and
very hard to do safely. In addition, in drm it is today almost
impossible to get hold of the framebuffer address.
So drop support for this.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Hans Verkuil [Thu, 2 Mar 2023 12:57:24 +0000 (13:57 +0100)]
media: saa7134: drop overlay support
Destructive overlay support (i.e. where the video frame is DMA-ed
straight into a framebuffer) is effectively dead. It was a
necessary evil in the early days when computers were not fast enough
to copy SDTV video frames around, but today that's no longer a problem.
It requires access to the framebuffer memory, which is a bad idea and
very hard to do safely. In addition, in drm it is today almost
impossible to get hold of the framebuffer address.
So drop support for this.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Hans Verkuil [Thu, 2 Mar 2023 12:57:23 +0000 (13:57 +0100)]
media: saa7146: drop overlay support
Destructive overlay support (i.e. where the video frame is DMA-ed
straight into a framebuffer) is effectively dead. It was a
necessary evil in the early days when computers were not fast enough
to copy SDTV video frames around, but today that's no longer a problem.
It requires access to the framebuffer memory, which is a bad idea and
very hard to do safely. In addition, in drm it is today almost
impossible to get hold of the framebuffer address.
So drop support for this.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Hans Verkuil [Wed, 1 Mar 2023 11:48:06 +0000 (12:48 +0100)]
media: common: btcx-risc.h: drop obsolete header
This header is no longer used, drop it.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Hans Verkuil [Wed, 1 Mar 2023 11:47:36 +0000 (12:47 +0100)]
media: zoran: drop two obsolete prototypes from zoran_device.h
These overlay-related functions no longer exist, so drop them
from the header.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Hans Verkuil [Wed, 1 Mar 2023 11:13:45 +0000 (12:13 +0100)]
media: stm32: dma2d: remove unused fb_buf
Drop the unused struct v4l2_framebuffer fb_buf in struct dma2d_ctx.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
CC: Hugues Fruchet <hugues.fruchet@foss.st.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Hans Verkuil [Wed, 15 Feb 2023 11:01:51 +0000 (12:01 +0100)]
media: admin-guide/media/cec.rst: update CEC debugging doc
The documentation on how to create your own Raspberry Pi CEC debugger was a
bit out of date. Update it to the Raspberry Pi 4B, drop the mention of the RTC
and a link to a picture that no longer works.
Also reorganize the text to make it easier to follow and change the pins to
match the pins I use.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Daniel Lundberg Pedersen [Tue, 7 Mar 2023 13:36:17 +0000 (14:36 +0100)]
media: docs: vidioc-g-ext-ctrls.rst: Document p_s32 and p_s64 fields
p_s32 and p_s64 were added to the v4l2_ext_control struct, so these
should have documentation as well.
Signed-off-by: Daniel Lundberg Pedersen <dlp@qtec.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Tom Rix [Sat, 11 Mar 2023 13:48:47 +0000 (14:48 +0100)]
media: pvrusb2: VIDEO_PVRUSB2 depends on DVB_CORE to use dvb_* symbols
A rand config causes this link error
vmlinux.o: In function `pvr2_dvb_create':
(.text+0x8af1d2): undefined reference to `dvb_register_adapter'
The rand config has
CONFIG_VIDEO_PVRUSB2=y
CONFIG_VIDEO_DEV=y
CONFIG_DVB_CORE=m
VIDEO_PVRUSB2 should also depend on DVB_CORE.
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Kevin Chiu [Tue, 7 Mar 2023 12:58:45 +0000 (13:58 +0100)]
media: platform: cros-ec: Add Gladios/Lisbon to the match table
The Google Gladios/Lisbon device uses the same approach as the Google Brask
which enables the HDMI CEC via the cros-ec-cec driver.
Signed-off-by: Kevin Chiu <kevin.chiu.17802@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Dan Carpenter [Tue, 7 Mar 2023 10:00:23 +0000 (11:00 +0100)]
media: av7110: prevent underflow in write_ts_to_decoder()
The buf[4] value comes from the user via ts_play(). It is a value in
the u8 range. The final length we pass to av7110_ipack_instant_repack()
is "len - (buf[4] + 1) - 4" so add a check to ensure that the length is
not negative. It's not clear that passing a negative len value does
anything bad necessarily, but it's not best practice.
With the new bounds checking the "if (!len)" condition is no longer
possible or required so remove that.
Fixes:
fd46d16d602a ("V4L/DVB (11759): dvb-ttpci: Add TS replay capability")
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
oushixiong [Tue, 7 Mar 2023 05:57:48 +0000 (06:57 +0100)]
media: mtk-jpegenc: Fix a compilation issue
‘mtk8195_jpegenc_drvdata’ defined but not used [-Werror=unused-variable]
Signed-off-by: oushixiong <oushixiong@kylinos.cn>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Marek Vasut [Sun, 5 Mar 2023 20:51:07 +0000 (21:51 +0100)]
media: stm32-dcmi: Enable incoherent buffer allocation
Set allow_cache_hints to 1 for the vb2_queue capture queue in the
STM32MP15xx DCMI V4L2 driver. This allows us to allocate buffers
with the V4L2_MEMORY_FLAG_NON_COHERENT set. On STM32MP15xx SoCs,
this enables caching for this memory, which improves performance
when being read from CPU.
This change should be safe from race conditions since videobuf2
already invalidates or flushes the appropriate cache lines in
its prepare() and finish() methods.
Tested on a STM32MP157F SoC. Resulted in 4x buffer access speedup.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
harperchen [Fri, 3 Mar 2023 15:30:11 +0000 (16:30 +0100)]
media: pci: tw68: Fix null-ptr-deref bug in buf prepare and finish
When the driver calls tw68_risc_buffer() to prepare the buffer, the
function call dma_alloc_coherent may fail, resulting in a empty buffer
buf->cpu. Later when we free the buffer or access the buffer, null ptr
deref is triggered.
This bug is similar to the following one:
https://git.linuxtv.org/media_stage.git/commit/?id=
2b064d91440b33fba5b452f2d1b31f13ae911d71.
We believe the bug can be also dynamically triggered from user side.
Similarly, we fix this by checking the return value of tw68_risc_buffer()
and the value of buf->cpu before buffer free.
Signed-off-by: harperchen <harperchen1110@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
harperchen [Fri, 3 Mar 2023 11:16:24 +0000 (12:16 +0100)]
media: platform: via: Handle error for dma_set_mask
As the potential failure of the dma_set_mask(), we fix this
bug by checking its return value and performing proper error
handling.
Signed-off-by: harperchen <harperchen1110@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Bryan O'Donoghue [Thu, 2 Mar 2023 15:53:53 +0000 (16:53 +0100)]
media: MAINTAINERS: Add myself as CAMSS maintainer
I discussed with Robert a few ago lending a hand with CAMSS. Following up
on that discussion, I'm happy to help.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
harperchen [Thu, 2 Mar 2023 12:39:05 +0000 (13:39 +0100)]
media: cx23885: Fix a null-ptr-deref bug in buffer_prepare() and buffer_finish()
When the driver calls cx23885_risc_buffer() to prepare the buffer, the
function call dma_alloc_coherent may fail, resulting in a empty buffer
risc->cpu. Later when we free the buffer or access the buffer, null ptr
deref is triggered.
This bug is similar to the following one:
https://git.linuxtv.org/media_stage.git/commit/?id=
2b064d91440b33fba5b452f2d1b31f13ae911d71.
We believe the bug can be also dynamically triggered from user side.
Similarly, we fix this by checking the return value of cx23885_risc_buffer()
and the value of risc->cpu before buffer free.
Signed-off-by: harperchen <harperchen1110@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Ming Qian [Thu, 2 Mar 2023 05:34:10 +0000 (06:34 +0100)]
media: amphion: decoder implement display delay enable
amphion vpu support a low latency mode,
when V4L2_CID_MPEG_VIDEO_DEC_DISPLAY_DELAY_ENABLE is enabled,
decoder can display frame immediately after it's decoded.
Only h264 is support yet.
Fixes:
6de8d628df6e ("media: amphion: add v4l2 m2m vpu decoder stateful driver")
Signed-off-by: Ming Qian <ming.qian@nxp.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Zoey Wu [Thu, 23 Feb 2023 05:41:38 +0000 (06:41 +0100)]
media: platform: cros-ec: Add aurash to the match table
The Google aurash device uses the same approach as the Google Brask
which enables the HDMI CEC via the cros-ec-cec driver.
Signed-off-by: Zoey Wu <zoey_wu@wistron.corp-partner.google.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Jiasheng Jiang [Thu, 9 Feb 2023 13:52:45 +0000 (14:52 +0100)]
media: platform: mtk-mdp3: Add missing check and free for ida_alloc
Add the check for the return value of the ida_alloc in order to avoid
NULL pointer dereference.
Moreover, free allocated "ctx->id" if mdp_m2m_open fails later in order
to avoid memory leak.
Fixes:
61890ccaefaf ("media: platform: mtk-mdp3: add MediaTek MDP3 driver")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Ye Xingchen [Wed, 8 Feb 2023 09:01:06 +0000 (10:01 +0100)]
media: platform: stm32: use devm_platform_get_and_ioremap_resource()
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Ye Xingchen <ye.xingchen@zte.com.cn>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Ye Xingchen [Wed, 8 Feb 2023 08:59:40 +0000 (09:59 +0100)]
media: platform: renesas: use devm_platform_get_and_ioremap_resource()
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Ye Xingchen <ye.xingchen@zte.com.cn>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Ye Xingchen [Wed, 8 Feb 2023 08:35:44 +0000 (09:35 +0100)]
media: dw100: use devm_platform_get_and_ioremap_resource()
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Ye Xingchen <ye.xingchen@zte.com.cn>
Reviewed-by: Xavier Roumegue <xavier.roumegue@oss.nxp.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Jiasheng Jiang [Wed, 8 Feb 2023 07:14:42 +0000 (08:14 +0100)]
media: bdisp: Add missing check for create_workqueue
Add the check for the return value of the create_workqueue
in order to avoid NULL pointer dereference.
Fixes:
28ffeebbb7bd ("[media] bdisp: 2D blitter driver using v4l2 mem2mem framework")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Kees Cook [Sat, 4 Feb 2023 18:38:05 +0000 (19:38 +0100)]
media: imx-jpeg: Bounds check sizeimage access
The call of mxc_jpeg_get_plane_size() from mxc_jpeg_dec_irq() sets
plane_no argument to 1. The compiler sees that it's possible to end up
with an access beyond the bounds of sizeimage, if mem_planes was too
large:
if (plane_no >= fmt->mem_planes) // mem_planes = 2+
return 0;
if (fmt->mem_planes == fmt->comp_planes) // comp_planes != mem_planes
return q_data->sizeimage[plane_no];
if (plane_no < fmt->mem_planes - 1) // mem_planes = 2
return q_data->sizeimage[plane_no];
comp_planes == 0 or 1 is safe. comp_planes > 2 would be out of bounds.
(This isn't currently possible given the contents of mxc_formats, though.)
Silence the warning by bounds checking comp_planes for future
robustness. Seen with GCC 13:
In function 'mxc_jpeg_get_plane_size',
inlined from 'mxc_jpeg_dec_irq' at ../drivers/media/platform/nxp/imx-jpeg/mxc-jpeg.c:729:14:
../drivers/media/platform/nxp/imx-jpeg/mxc-jpeg.c:641:42: warning: array subscript 2 is above array bounds of 'u32[2]' {aka 'unsigned int[2]'} [-Warray-bounds=]
641 | size += q_data->sizeimage[i];
| ~~~~~~~~~~~~~~~~~^~~
In file included from ../drivers/media/platform/nxp/imx-jpeg/mxc-jpeg-hw.h:112,
from ../drivers/media/platform/nxp/imx-jpeg/mxc-jpeg.c:63:
../drivers/media/platform/nxp/imx-jpeg/mxc-jpeg.h: In function 'mxc_jpeg_dec_irq':
../drivers/media/platform/nxp/imx-jpeg/mxc-jpeg.h:84:41: note: while referencing 'sizeimage'
84 | u32 sizeimage[MXC_JPEG_MAX_PLANES];
| ^~~~~~~~~
Cc: Mirela Rabulea <mirela.rabulea@nxp.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Kees Cook [Sat, 4 Feb 2023 18:36:17 +0000 (19:36 +0100)]
media: mxl5005s: Bounds check size used for max array index
The use of state->CH_Ctrl[i].size in a shift operation implies that its
value can be as much as 32, but the state->CH_Ctrl[i].val array is only
25 in size. Bounds check the size before shifting and looping. Fixes
warnings seen with GCC 13:
../drivers/media/tuners/mxl5005s.c: In function 'MXL_ControlWrite_Group.isra':
../drivers/media/tuners/mxl5005s.c:3450:70: warning: array subscript 32 is above array bounds of 'u16[25]' {aka 'short unsigned int[25]'} [-Warray-bounds=]
3450 | state->CH_Ctrl[i].val[j] = (u8)((value >> j) & 0x01);
| ~~~~~~~~~~~~~~~~~~~~~^~~
../drivers/media/tuners/mxl5005s.c:238:13: note: while referencing 'val'
238 | u16 val[25]; /* Binary representation of Value */
| ^~~
Cc: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Jakub Kicinski [Fri, 3 Feb 2023 23:31:29 +0000 (00:31 +0100)]
media: drop unnecessary networking includes
dvb_net.h includes a bunch of core networking headers which increases
the number of objects rebuilt when we touch them. They are unnecessary
for the header itself and only one driver has an indirect dependency.
tveeprom.h includes if_packet to gain access to ETH_ALEN. This
is a bit of an overkill because if_packet.h pulls in skbuff.h.
The definition of ETH_ALEN is in the uAPI header, which is
very rarely touched, so switch to including that.
This results in roughly 250 fewer objects built when skbuff.h
is touched (6028 -> 5788).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Jonathan Neuschäfer [Sun, 29 Jan 2023 16:16:18 +0000 (17:16 +0100)]
media: dvb-frontends: Fix a typo ("Unknow sleep mode")
Spell "unknown" correctly.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Krzysztof Kozlowski [Fri, 9 Dec 2022 17:59:26 +0000 (18:59 +0100)]
media: dt-bindings: silabs,si470x: Convert to DT schema
Convert the Silicon Labs Si470x FM Radio Receiver bindings to DT schema.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Colin Ian King [Thu, 8 Dec 2022 11:58:47 +0000 (12:58 +0100)]
media: platform: exynos4-is: Fix spelling mistake "palne" -> "plane"
There are spelling mistakes in a literal string and a comment. Fix them.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Yang Li [Thu, 10 Nov 2022 01:36:48 +0000 (02:36 +0100)]
media: tc358746: Remove unneeded semicolon
./drivers/media/i2c/tc358746.c:857:3-4: Unneeded semicolon
./drivers/media/i2c/tc358746.c:861:2-3: Unneeded semicolon
Link: https://bugzilla.openanolis.cn/show_bug.cgi?id=2832
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Christian Hewitt [Sat, 4 Feb 2023 07:45:01 +0000 (08:45 +0100)]
media: rc: add Beelink Mini MXIII keymap
Add a keymap for the simple IR (NEC) remote used with the Beelink
Mini MXIII Android STB device.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Christian Hewitt [Sat, 4 Feb 2023 07:45:00 +0000 (08:45 +0100)]
media: dt-bindings: rc: add rc-beelink-mxiii
Add a binding for the rc-beelink-mxiii remote keymap
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Emanuel Strobel [Fri, 3 Feb 2023 09:34:05 +0000 (10:34 +0100)]
media: rc: add common keymap for Dreambox RC10/RC0 and RC20/RC-BT remotes
Add a common keymap for the RC10/RC0 and RC20/RC-BT remotes used with
the Dreambox One and Dreambox Two DVB-S/T boxes. The maps are combined
since the IR codes do not conflict and both boxes have shipped with
both remote designs over time.
Both remote types can be programmed to control TVs, so include non-IR
keys that are used to switch-to or toggle the remote mode:
- DREAM in RC10/RC0 switches to (Dreambox) STB control mode
- TV in RC10/RC0 switches to TV control mode
- MODE in RC20/RC-BT toggles between STB/TV/BT control modes
In the RC20 keymap the Android MIC (voice search) key maps to KEY_HELP
and EXIT is mapped to KEY_ESC to replicate the go-backwards navigation
behaviour in the Android vendor OS that ships on Dreambox devices.
Signed-off-by: Emanuel Strobel <emanuel.strobel@yahoo.com>
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Christian Hewitt [Fri, 3 Feb 2023 09:34:04 +0000 (10:34 +0100)]
media: dt-bindings: rc: add rc-dreambox
Add a binding for the rc-dreambox remote keymap
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Hans Verkuil [Wed, 1 Feb 2023 12:56:46 +0000 (13:56 +0100)]
media: cx18: fix format compliance issues
This properly fills in all the format fields and calculates the
width and height correctly.
Esp. the minimum width and height was wrong.
When changing the standard the width and height also have to be
reset to the corresponding default width/height for the chosen
standard.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Hans Verkuil [Wed, 1 Feb 2023 12:56:20 +0000 (13:56 +0100)]
media: cx18: reorder fmt_vid_cap functions in cx18-ioctl.c
No actual code changed, this just reorders functions so that the
g/try/s_fmt_vid_cap functions are all together rather than mixed in
with the vbi format functions.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Hans Verkuil [Wed, 1 Feb 2023 12:54:20 +0000 (13:54 +0100)]
media: cx18: missing CAP_AUDIO for vbi stream
The v4l2-compliance test complained about this. You can change the
input connector for the vbi stream, but that means that you can have to
be able to do the same for the audio input.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Hans Verkuil [Wed, 1 Feb 2023 11:50:30 +0000 (12:50 +0100)]
media: cx18: properly report pixelformats
The MPEG device reported non-MPEG pixelformats, and the YUV device reported
the MPEG pixelformat as well.
Separate the two: either report MPEG or HM12/UYUV, not all three.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Hans Verkuil [Wed, 1 Feb 2023 11:19:46 +0000 (12:19 +0100)]
media: cx18: fix incorrect input counting
Counting the number of video and audio inputs was wrong if the
number of inputs equalled CX18_CARD_MAX_VIDEO_INPUTS or
CX18_CARD_MAX_AUDIO_INPUTS. This was a copy-and-paste from the
ivtv driver. That driver has been fixed quite a long time ago,
but we missed that this driver had the same bug.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Hans Verkuil [Tue, 31 Jan 2023 10:34:54 +0000 (11:34 +0100)]
media: cx18: convert to vb2
This patch converts cx18 from the old deprecated videobuf framework
to the 'new' vb2 framework.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Hans Verkuil [Wed, 1 Feb 2023 11:48:54 +0000 (12:48 +0100)]
media: v4l2-dev.c: check for V4L2_CAP_STREAMING to enable streaming ioctls
Rather than checking which device type it is, just check the STREAMING
cap since that indicates support for streaming ioctls.
Some drivers only support READWRITE (typically MPEG encoders).
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Hans Verkuil [Wed, 1 Feb 2023 13:06:47 +0000 (14:06 +0100)]
media: vb2: set owner before calling vb2_read
Before vb2_read is called, the owner must be set since vb2_read will
actually start streaming. If vb2_read returns an error and q->fileio is
NULL, then it failed to start streaming and the owner is set back to NULL.
When the vb2 start_streaming callback is called, it expects the owner
pointer to be set, and that wasn't the case in this particular situation.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Sakari Ailus [Fri, 24 Feb 2023 15:00:46 +0000 (16:00 +0100)]
media: v4l: subdev: Make link validation safer
Link validation currently accesses invalid pointers if the link passed to
it is not between two sub-devices. This is of course a driver bug.
Ignore the error but print a warning message, as this is how it used to
work previously.
Fixes:
a6b995ed03ff ("media: subdev: use streams in v4l2_subdev_link_validate()")
Reported-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Tomi Valkeinen [Fri, 3 Mar 2023 15:52:49 +0000 (16:52 +0100)]
media: subdev: Fix validation state lockdep issue
The new subdev state code has a possible deadlock scenario during link
validation when the pipeline contains subdevs that support state and
that do not support state.
The current code locks the states of the subdevs on both ends of the
link when starting the link validation, locking the sink side first,
then the source. If either (or both) of the subdevs does not support
state, nothing is done for that subdev at this point, and instead the
locking is handled the old way, i.e. the subdev's ops do the locking
internally.
The issue arises when the sink doesn't support state, but source does,
so the validation code locks the source for the duration of the
validation, and then the sink is locked only when the get_fmt op is
called. So lockdep sees the source locked first, then the sink.
Later, when the streaming is started, the sink's s_stream op is called,
which probably takes the subdev's lock. The op then calls the source's
s_stream, which takes the source's lock. So, the sink is locked first,
then the source.
Note that link validation and stream starting is not done at the same
time, so an actual deadlock should never happen. However, it's still a
clear bug.
Fix this by locking the subdev states only if both subdevs support
state. In other words, we have two scenarios:
1. Both subdevs support state. Lock sink first, then source, and keep
the locks while validating the link.
2. At least one of the subdevs do not support state. Take the lock only
for the duration of the operation (get_fmt or looking at the
routing), and release after the op is done.
Obviously 1. is better, as we have a more consistent view of the states
of the subdevs during validation. 2. is how it has been so far, so it's
no worse than this used to be.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Arnd Bergmann [Tue, 7 Feb 2023 16:13:12 +0000 (17:13 +0100)]
media: i2c: imx290: fix conditional function definitions
The runtime suspend/resume functions are only referenced from the
dev_pm_ops, but they use the old SET_RUNTIME_PM_OPS() helper
that requires a __maybe_unused annotation to avoid a warning:
drivers/media/i2c/imx290.c:1082:12: error: unused function 'imx290_runtime_resume' [-Werror,-Wunused-function]
static int imx290_runtime_resume(struct device *dev)
^
drivers/media/i2c/imx290.c:1090:12: error: unused function 'imx290_runtime_suspend' [-Werror,-Wunused-function]
static int imx290_runtime_suspend(struct device *dev)
^
Convert this to the new RUNTIME_PM_OPS() helper that so this
is not required. To improve this further, also use the pm_ptr()
helper that lets the dev_pm_ops get dropped entirely when
CONFIG_PM is disabled.
A related mistake happened in the of_match_ptr() macro here, which
like SET_RUNTIME_PM_OPS() requires the match table to be marked
as __maybe_unused, though I could not reproduce building this without
CONFIG_OF. Remove the of_match_ptr() here as there is no point in
dropping the match table in configurations without CONFIG_OF.
Fixes:
02852c01f654 ("media: i2c: imx290: Initialize runtime PM before subdev")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Javier Martinez Canillas [Tue, 7 Feb 2023 10:22:54 +0000 (11:22 +0100)]
media: Revert "venus: firmware: Correct non-pix start and end addresses"
This reverts commit
a837e5161cfffbb3242cc0eb574f8bf65fd32640, which broke
probing of the venus driver, at least on the SC7180 SoC HP X2 Chromebook:
[ 11.455782] qcom-venus aa00000.video-codec: Adding to iommu group 11
[ 11.506980] qcom-venus aa00000.video-codec: non legacy binding
[ 12.143432] qcom-venus aa00000.video-codec: failed to reset venus core
[ 12.156440] qcom-venus: probe of aa00000.video-codec failed with error -110
Matthias Kaehlcke also reported that the same change caused a regression in
SC7180 and sc7280, that prevents AOSS from entering sleep mode during system
suspend. So let's revert this commit for now to fix both issues.
Fixes:
a837e5161cff ("venus: firmware: Correct non-pix start and end addresses")
Reported-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Stanimir Varbanov <stanimir.k.varbanov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Linus Torvalds [Sun, 12 Mar 2023 23:36:44 +0000 (16:36 -0700)]
Linux 6.3-rc2
Hector Martin [Sat, 11 Mar 2023 14:19:14 +0000 (23:19 +0900)]
wifi: cfg80211: Partial revert "wifi: cfg80211: Fix use after free for wext"
This reverts part of commit
015b8cc5e7c4 ("wifi: cfg80211: Fix use after
free for wext")
This commit broke WPA offload by unconditionally clearing the crypto
modes for non-WEP connections. Drop that part of the patch.
Signed-off-by: Hector Martin <marcan@marcan.st>
Reported-by: Ilya <me@0upti.me>
Reported-and-tested-by: Janne Grunau <j@jannau.net>
Reviewed-by: Eric Curtin <ecurtin@redhat.com>
Fixes:
015b8cc5e7c4 ("wifi: cfg80211: Fix use after free for wext")
Cc: stable@kernel.org
Link: https://lore.kernel.org/linux-wireless/ZAx0TWRBlGfv7pNl@kroah.com/T/#m11e6e0915ab8fa19ce8bc9695ab288c0fe018edf
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sun, 12 Mar 2023 23:15:36 +0000 (16:15 -0700)]
Merge tag 'tpm-v6.3-rc3' of git://git./linux/kernel/git/jarkko/linux-tpmdd
Pull tpm fixes from Jarkko Sakkinen:
"Two additional bug fixes for v6.3"
* tag 'tpm-v6.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/jarkko/linux-tpmdd:
tpm: disable hwrng for fTPM on some AMD designs
tpm/eventlog: Don't abort tpm_read_log on faulty ACPI address
Mario Limonciello [Tue, 28 Feb 2023 02:44:39 +0000 (20:44 -0600)]
tpm: disable hwrng for fTPM on some AMD designs
AMD has issued an advisory indicating that having fTPM enabled in
BIOS can cause "stuttering" in the OS. This issue has been fixed
in newer versions of the fTPM firmware, but it's up to system
designers to decide whether to distribute it.
This issue has existed for a while, but is more prevalent starting
with kernel 6.1 because commit
b006c439d58db ("hwrng: core - start
hwrng kthread also for untrusted sources") started to use the fTPM
for hwrng by default. However, all uses of /dev/hwrng result in
unacceptable stuttering.
So, simply disable registration of the defective hwrng when detecting
these faulty fTPM versions. As this is caused by faulty firmware, it
is plausible that such a problem could also be reproduced by other TPM
interactions, but this hasn't been shown by any user's testing or reports.
It is hypothesized to be triggered more frequently by the use of the RNG
because userspace software will fetch random numbers regularly.
Intentionally continue to register other TPM functionality so that users
that rely upon PCR measurements or any storage of data will still have
access to it. If it's found later that another TPM functionality is
exacerbating this problem a module parameter it can be turned off entirely
and a module parameter can be introduced to allow users who rely upon
fTPM functionality to turn it on even though this problem is present.
Link: https://www.amd.com/en/support/kb/faq/pa-410
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216989
Link: https://lore.kernel.org/all/20230209153120.261904-1-Jason@zx2c4.com/
Fixes:
b006c439d58d ("hwrng: core - start hwrng kthread also for untrusted sources")
Cc: stable@vger.kernel.org
Cc: Jarkko Sakkinen <jarkko@kernel.org>
Cc: Thorsten Leemhuis <regressions@leemhuis.info>
Cc: James Bottomley <James.Bottomley@hansenpartnership.com>
Tested-by: reach622@mailcuk.com
Tested-by: Bell <1138267643@qq.com>
Co-developed-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Morten Linderud [Wed, 15 Feb 2023 09:25:52 +0000 (10:25 +0100)]
tpm/eventlog: Don't abort tpm_read_log on faulty ACPI address
tpm_read_log_acpi() should return -ENODEV when no eventlog from the ACPI
table is found. If the firmware vendor includes an invalid log address
we are unable to map from the ACPI memory and tpm_read_log() returns -EIO
which would abort discovery of the eventlog.
Change the return value from -EIO to -ENODEV when acpi_os_map_iomem()
fails to map the event log.
The following hardware was used to test this issue:
Framework Laptop (Pre-production)
BIOS: INSYDE Corp, Revision: 3.2
TPM Device: NTC, Firmware Revision: 7.2
Dump of the faulty ACPI TPM2 table:
[000h 0000 4] Signature : "TPM2" [Trusted Platform Module hardware interface Table]
[004h 0004 4] Table Length :
0000004C
[008h 0008 1] Revision : 04
[009h 0009 1] Checksum : 2B
[00Ah 0010 6] Oem ID : "INSYDE"
[010h 0016 8] Oem Table ID : "TGL-ULT"
[018h 0024 4] Oem Revision :
00000002
[01Ch 0028 4] Asl Compiler ID : "ACPI"
[020h 0032 4] Asl Compiler Revision :
00040000
[024h 0036 2] Platform Class : 0000
[026h 0038 2] Reserved : 0000
[028h 0040 8] Control Address :
0000000000000000
[030h 0048 4] Start Method : 06 [Memory Mapped I/O]
[034h 0052 12] Method Parameters : 00 00 00 00 00 00 00 00 00 00 00 00
[040h 0064 4] Minimum Log Length :
00010000
[044h 0068 8] Log Address :
000000004053D000
Fixes:
0cf577a03f21 ("tpm: Fix handling of missing event log")
Tested-by: Erkki Eilonen <erkki@bearmetal.eu>
Signed-off-by: Morten Linderud <morten@linderud.pw>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Linus Torvalds [Sun, 12 Mar 2023 16:47:08 +0000 (09:47 -0700)]
Merge tag 'xfs-6.3-fixes-1' of git://git./fs/xfs/xfs-linux
Pull xfs fixes from Darrick Wong:
- Fix a crash if mount time quotacheck fails when there are inodes
queued for garbage collection.
- Fix an off by one error when discarding folios after writeback
failure.
* tag 'xfs-6.3-fixes-1' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: fix off-by-one-block in xfs_discard_folio()
xfs: quotacheck failure can race with background inode inactivation
Linus Torvalds [Sun, 12 Mar 2023 16:17:30 +0000 (09:17 -0700)]
Merge tag 'staging-6.3-rc2' of git://git./linux/kernel/git/gregkh/staging
Pull staging driver fixes and removal from Greg KH:
"Here are four small staging driver fixes, and one big staging driver
deletion for 6.3-rc2.
The fixes are:
- rtl8192e driver fixes for where the driver was attempting to
execute various programs directly from the disk for unknown reasons
- rtl8723bs driver fixes for issues found by Hans in testing
The deleted driver is the removal of the r8188eu wireless driver as
now in 6.3-rc1 we have a "real" wifi driver for one that includes
support for many many more devices than this old driver did. So it's
time to remove it as it is no longer needed. The maintainers of this
driver all have acked its removal. Many thanks to them over the years
for working to clean it up and keep it working while the real driver
was being developed.
All of these have been in linux-next this week with no reported
problems"
* tag 'staging-6.3-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: r8188eu: delete driver
staging: rtl8723bs: Pass correct parameters to cfg80211_get_bss()
staging: rtl8723bs: Fix key-store index handling
staging: rtl8192e: Remove call_usermodehelper starting RadioPower.sh
staging: rtl8192e: Remove function ..dm_check_ac_dc_power calling a script
Linus Torvalds [Sun, 12 Mar 2023 16:12:03 +0000 (09:12 -0700)]
Merge tag 'x86_urgent_for_v6.3_rc2' of git://git./linux/kernel/git/tip/tip
Pull x86 fix from Borislav Petkov:
"A single erratum fix for AMD machines:
- Disable XSAVES on AMD Zen1 and Zen2 machines due to an erratum. No
impact to anything as those machines will fallback to XSAVEC which
is equivalent there"
* tag 'x86_urgent_for_v6.3_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/CPU/AMD: Disable XSAVES on AMD family 0x17
Linus Torvalds [Sun, 12 Mar 2023 16:04:28 +0000 (09:04 -0700)]
Merge tag 'kernel.fork.v6.3-rc2' of gitolite.pub/scm/linux/kernel/git/brauner/linux
Pull clone3 fix from Christian Brauner:
"A simple fix for the clone3() system call.
The CLONE_NEWTIME allows the creation of time namespaces. The flag
reuses a bit from the CSIGNAL bits that are used in the legacy clone()
system call to set the signal that gets sent to the parent after the
child exits.
The clone3() system call doesn't rely on CSIGNAL anymore as it uses a
dedicated .exit_signal field in struct clone_args. So we blocked all
CSIGNAL bits in clone3_args_valid(). When CLONE_NEWTIME was introduced
and reused a CSIGNAL bit we forgot to adapt clone3_args_valid()
causing CLONE_NEWTIME with clone3() to be rejected. Fix this"
* tag 'kernel.fork.v6.3-rc2' of gitolite.kernel.org:pub/scm/linux/kernel/git/brauner/linux:
selftests/clone3: test clone3 with CLONE_NEWTIME
fork: allow CLONE_NEWTIME in clone3 flags
Linus Torvalds [Sun, 12 Mar 2023 16:00:54 +0000 (09:00 -0700)]
Merge tag 'vfs.misc.v6.3-rc2' of git://git./linux/kernel/git/vfs/idmapping
Pull vfs fixes from Christian Brauner:
- When allocating pages for a watch queue failed, we didn't return an
error causing userspace to proceed even though all subsequent
notifcations would be lost. Make sure to return an error.
- Fix a misformed tree entry for the idmapping maintainers entry.
- When setting file leases from an idmapped mount via
generic_setlease() we need to take the idmapping into account
otherwise taking a lease would fail from an idmapped mount.
- Remove two redundant assignments, one in splice code and the other in
locks code, that static checkers complained about.
* tag 'vfs.misc.v6.3-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/idmapping:
filelocks: use mount idmapping for setlease permission check
fs/locks: Remove redundant assignment to cmd
splice: Remove redundant assignment to ret
MAINTAINERS: repair a malformed T: entry in IDMAPPED MOUNTS
watch_queue: fix IOC_WATCH_QUEUE_SET_SIZE alloc error paths
Linus Torvalds [Sun, 12 Mar 2023 15:55:55 +0000 (08:55 -0700)]
Merge tag 'ext4_for_linus_stable' of git://git./linux/kernel/git/tytso/ext4
Pull ext4 fixes from Ted Ts'o:
"Bug fixes and regressions for ext4, the most serious of which is a
potential deadlock during directory renames that was introduced during
the merge window discovered by a combination of syzbot and lockdep"
* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: zero i_disksize when initializing the bootloader inode
ext4: make sure fs error flag setted before clear journal error
ext4: commit super block if fs record error when journal record without error
ext4, jbd2: add an optimized bmap for the journal inode
ext4: fix WARNING in ext4_update_inline_data
ext4: move where set the MAY_INLINE_DATA flag is set
ext4: Fix deadlock during directory rename
ext4: Fix comment about the 64BIT feature
docs: ext4: modify the group desc size to 64
ext4: fix another off-by-one fsmap error on 1k block filesystems
ext4: fix RENAME_WHITEOUT handling for inline directories
ext4: make kobj_type structures constant
ext4: fix cgroup writeback accounting with fs-layer encryption
Linus Torvalds [Sun, 12 Mar 2023 15:52:03 +0000 (08:52 -0700)]
cpumask: relax sanity checking constraints
The cpumask_check() was unnecessarily tight, and causes problems for the
users of cpumask_next().
We have a number of users that take the previous return value of one of
the bit scanning functions and subtract one to keep it in "range". But
since the scanning functions end up returning up to 'small_cpumask_bits'
instead of the tighter 'nr_cpumask_bits', the range really needs to be
using that widened form.
[ This "previous-1" behavior is also the reason we have all those
comments about /* -1 is a legal arg here. */ and separate checks for
that being ok. So we could have just made "small_cpumask_bits-1"
be a similar special "don't check this" value.
Tetsuo Handa even suggested a patch that only does that for
cpumask_next(), since that seems to be the only actual case that
triggers, but that all makes it even _more_ magical and special. So
just relax the check ]
One example of this kind of pattern being the 'c_start()' function in
arch/x86/kernel/cpu/proc.c, but also duplicated in various forms on
other architectures.
Reported-by: syzbot+96cae094d90877641f32@syzkaller.appspotmail.com
Link: https://syzkaller.appspot.com/bug?extid=96cae094d90877641f32
Reported-by: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Link: https://lore.kernel.org/lkml/c1f4cc16-feea-b83c-82cf-1a1f007b7eb9@I-love.SAKURA.ne.jp/
Fixes:
596ff4a09b89 ("cpumask: re-introduce constant-sized cpumask optimizations")
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sat, 11 Mar 2023 17:24:05 +0000 (09:24 -0800)]
Merge tag 'i2c-for-6.3-rc2' of git://git./linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
"This marks the end of a transition to let I2C have the same probe
semantics as other subsystems. Uwe took care that no drivers in the
current tree nor in -next use the deprecated .probe call. So, it is a
good time to switch to the new, standard semantics now.
There is also a regression fix:
- regression fix for the notifier handling of the I2C core
- final coversions of drivers away from deprecated .probe
- make .probe_new the standard probe and convert I2C core to use it
* tag 'i2c-for-6.3-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: dev: Fix bus callback return values
i2c: Convert drivers to new .probe() callback
i2c: mux: Convert all drivers to new .probe() callback
i2c: Switch .probe() to not take an id parameter
media: i2c: ov2685: convert to i2c's .probe_new()
media: i2c: ov5695: convert to i2c's .probe_new()
w1: ds2482: Convert to i2c's .probe_new()
serial: sc16is7xx: Convert to i2c's .probe_new()
mtd: maps: pismo: Convert to i2c's .probe_new()
misc: ad525x_dpot-i2c: Convert to i2c's .probe_new()
Richard Weinberger [Sat, 11 Mar 2023 09:29:29 +0000 (10:29 +0100)]
ubi: block: Fix missing blk_mq_end_request
Switching to BLK_MQ_F_BLOCKING wrongly removed the call to
blk_mq_end_request(). Add it back to have our IOs finished
Fixes:
91cc8fbcc8c7 ("ubi: block: set BLK_MQ_F_BLOCKING")
Analyzed-by: Linus Torvalds <torvalds@linux-foundation.org>
Reported-by: Daniel Palmer <daniel@0x0f.com>
Link: https://lore.kernel.org/linux-mtd/CAHk-=wi29bbBNh3RqJKu3PxzpjDN5D5K17gEVtXrb7-6bfrnMQ@mail.gmail.com/
Signed-off-by: Richard Weinberger <richard@nod.at>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Tested-by: Daniel Palmer <daniel@0x0f.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Zhihao Cheng [Wed, 8 Mar 2023 03:26:43 +0000 (11:26 +0800)]
ext4: zero i_disksize when initializing the bootloader inode
If the boot loader inode has never been used before, the
EXT4_IOC_SWAP_BOOT inode will initialize it, including setting the
i_size to 0. However, if the "never before used" boot loader has a
non-zero i_size, then i_disksize will be non-zero, and the
inconsistency between i_size and i_disksize can trigger a kernel
warning:
WARNING: CPU: 0 PID: 2580 at fs/ext4/file.c:319
CPU: 0 PID: 2580 Comm: bb Not tainted 6.3.0-rc1-00004-g703695902cfa
RIP: 0010:ext4_file_write_iter+0xbc7/0xd10
Call Trace:
vfs_write+0x3b1/0x5c0
ksys_write+0x77/0x160
__x64_sys_write+0x22/0x30
do_syscall_64+0x39/0x80
Reproducer:
1. create corrupted image and mount it:
mke2fs -t ext4 /tmp/foo.img 200
debugfs -wR "sif <5> size 25700" /tmp/foo.img
mount -t ext4 /tmp/foo.img /mnt
cd /mnt
echo 123 > file
2. Run the reproducer program:
posix_memalign(&buf, 1024, 1024)
fd = open("file", O_RDWR | O_DIRECT);
ioctl(fd, EXT4_IOC_SWAP_BOOT);
write(fd, buf, 1024);
Fix this by setting i_disksize as well as i_size to zero when
initiaizing the boot loader inode.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217159
Cc: stable@kernel.org
Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com>
Link: https://lore.kernel.org/r/20230308032643.641113-1-chengzhihao1@huawei.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Ye Bin [Tue, 7 Mar 2023 06:17:03 +0000 (14:17 +0800)]
ext4: make sure fs error flag setted before clear journal error
Now, jounral error number maybe cleared even though ext4_commit_super()
failed. This may lead to error flag miss, then fsck will miss to check
file system deeply.
Signed-off-by: Ye Bin <yebin10@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20230307061703.245965-3-yebin@huaweicloud.com
Ye Bin [Tue, 7 Mar 2023 06:17:02 +0000 (14:17 +0800)]
ext4: commit super block if fs record error when journal record without error
Now, 'es->s_state' maybe covered by recover journal. And journal errno
maybe not recorded in journal sb as IO error. ext4_update_super() only
update error information when 'sbi->s_add_error_count' large than zero.
Then 'EXT4_ERROR_FS' flag maybe lost.
To solve above issue just recover 'es->s_state' error flag after journal
replay like error info.
Signed-off-by: Ye Bin <yebin10@huawei.com>
Reviewed-by: Baokun Li <libaokun1@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20230307061703.245965-2-yebin@huaweicloud.com
Theodore Ts'o [Wed, 8 Mar 2023 04:15:49 +0000 (23:15 -0500)]
ext4, jbd2: add an optimized bmap for the journal inode
The generic bmap() function exported by the VFS takes locks and does
checks that are not necessary for the journal inode. So allow the
file system to set a journal-optimized bmap function in
journal->j_bmap.
Reported-by: syzbot+9543479984ae9e576000@syzkaller.appspotmail.com
Link: https://syzkaller.appspot.com/bug?id=e4aaa78795e490421c79f76ec3679006c8ff4cf0
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Ye Bin [Tue, 7 Mar 2023 01:52:53 +0000 (09:52 +0800)]
ext4: fix WARNING in ext4_update_inline_data
Syzbot found the following issue:
EXT4-fs (loop0): mounted filesystem
00000000-0000-0000-0000-
000000000000 without journal. Quota mode: none.
fscrypt: AES-256-CTS-CBC using implementation "cts-cbc-aes-aesni"
fscrypt: AES-256-XTS using implementation "xts-aes-aesni"
------------[ cut here ]------------
WARNING: CPU: 0 PID: 5071 at mm/page_alloc.c:5525 __alloc_pages+0x30a/0x560 mm/page_alloc.c:5525
Modules linked in:
CPU: 1 PID: 5071 Comm: syz-executor263 Not tainted 6.2.0-rc1-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 10/26/2022
RIP: 0010:__alloc_pages+0x30a/0x560 mm/page_alloc.c:5525
RSP: 0018:
ffffc90003c2f1c0 EFLAGS:
00010246
RAX:
ffffc90003c2f220 RBX:
0000000000000014 RCX:
0000000000000000
RDX:
0000000000000028 RSI:
0000000000000000 RDI:
ffffc90003c2f248
RBP:
ffffc90003c2f2d8 R08:
dffffc0000000000 R09:
ffffc90003c2f220
R10:
fffff52000785e49 R11:
1ffff92000785e44 R12:
0000000000040d40
R13:
1ffff92000785e40 R14:
dffffc0000000000 R15:
1ffff92000785e3c
FS:
0000555556c0d300(0000) GS:
ffff8880b9800000(0000) knlGS:
0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
CR2:
00007f95d5e04138 CR3:
00000000793aa000 CR4:
00000000003506f0
DR0:
0000000000000000 DR1:
0000000000000000 DR2:
0000000000000000
DR3:
0000000000000000 DR6:
00000000fffe0ff0 DR7:
0000000000000400
Call Trace:
<TASK>
__alloc_pages_node include/linux/gfp.h:237 [inline]
alloc_pages_node include/linux/gfp.h:260 [inline]
__kmalloc_large_node+0x95/0x1e0 mm/slab_common.c:1113
__do_kmalloc_node mm/slab_common.c:956 [inline]
__kmalloc+0xfe/0x190 mm/slab_common.c:981
kmalloc include/linux/slab.h:584 [inline]
kzalloc include/linux/slab.h:720 [inline]
ext4_update_inline_data+0x236/0x6b0 fs/ext4/inline.c:346
ext4_update_inline_dir fs/ext4/inline.c:1115 [inline]
ext4_try_add_inline_entry+0x328/0x990 fs/ext4/inline.c:1307
ext4_add_entry+0x5a4/0xeb0 fs/ext4/namei.c:2385
ext4_add_nondir+0x96/0x260 fs/ext4/namei.c:2772
ext4_create+0x36c/0x560 fs/ext4/namei.c:2817
lookup_open fs/namei.c:3413 [inline]
open_last_lookups fs/namei.c:3481 [inline]
path_openat+0x12ac/0x2dd0 fs/namei.c:3711
do_filp_open+0x264/0x4f0 fs/namei.c:3741
do_sys_openat2+0x124/0x4e0 fs/open.c:1310
do_sys_open fs/open.c:1326 [inline]
__do_sys_openat fs/open.c:1342 [inline]
__se_sys_openat fs/open.c:1337 [inline]
__x64_sys_openat+0x243/0x290 fs/open.c:1337
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x3d/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
Above issue happens as follows:
ext4_iget
ext4_find_inline_data_nolock ->i_inline_off=164 i_inline_size=60
ext4_try_add_inline_entry
__ext4_mark_inode_dirty
ext4_expand_extra_isize_ea ->i_extra_isize=32 s_want_extra_isize=44
ext4_xattr_shift_entries
->after shift i_inline_off is incorrect, actually is change to 176
ext4_try_add_inline_entry
ext4_update_inline_dir
get_max_inline_xattr_value_size
if (EXT4_I(inode)->i_inline_off)
entry = (struct ext4_xattr_entry *)((void *)raw_inode +
EXT4_I(inode)->i_inline_off);
free += EXT4_XATTR_SIZE(le32_to_cpu(entry->e_value_size));
->As entry is incorrect, then 'free' may be negative
ext4_update_inline_data
value = kzalloc(len, GFP_NOFS);
-> len is unsigned int, maybe very large, then trigger warning when
'kzalloc()'
To resolve the above issue we need to update 'i_inline_off' after
'ext4_xattr_shift_entries()'. We do not need to set
EXT4_STATE_MAY_INLINE_DATA flag here, since ext4_mark_inode_dirty()
already sets this flag if needed. Setting EXT4_STATE_MAY_INLINE_DATA
when it is needed may trigger a BUG_ON in ext4_writepages().
Reported-by: syzbot+d30838395804afc2fa6f@syzkaller.appspotmail.com
Cc: stable@kernel.org
Signed-off-by: Ye Bin <yebin10@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20230307015253.2232062-3-yebin@huaweicloud.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Ye Bin [Tue, 7 Mar 2023 01:52:52 +0000 (09:52 +0800)]
ext4: move where set the MAY_INLINE_DATA flag is set
The only caller of ext4_find_inline_data_nolock() that needs setting of
EXT4_STATE_MAY_INLINE_DATA flag is ext4_iget_extra_inode(). In
ext4_write_inline_data_end() we just need to update inode->i_inline_off.
Since we are going to add one more caller that does not need to set
EXT4_STATE_MAY_INLINE_DATA, just move setting of EXT4_STATE_MAY_INLINE_DATA
out to ext4_iget_extra_inode().
Signed-off-by: Ye Bin <yebin10@huawei.com>
Cc: stable@kernel.org
Reviewed-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20230307015253.2232062-2-yebin@huaweicloud.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Linus Torvalds [Sat, 11 Mar 2023 04:45:53 +0000 (20:45 -0800)]
Merge tag 'scsi-fixes' of git://git./linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Twenty fixes all in drivers except the one zone storage revalidation
fix to sd.
The megaraid_sas fixes are more on the level of a driver update
(enabling crash dump and increasing lun number) but I thought you
could let this slide on -rc1 and the next most extensive update is a
load of fixes to mpi3mr"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: sd: Fix wrong zone_write_granularity value during revalidate
scsi: storvsc: Handle BlockSize change in Hyper-V VHD/VHDX file
scsi: megaraid_sas: Driver version update to 07.725.01.00-rc1
scsi: megaraid_sas: Add crash dump mode capability bit in MFI capabilities
scsi: megaraid_sas: Update max supported LD IDs to 240
scsi: mpi3mr: Bad drive in topology results kernel crash
scsi: mpi3mr: NVMe command size greater than 8K fails
scsi: mpi3mr: Return proper values for failures in firmware init path
scsi: mpi3mr: Wait for diagnostic save during controller init
scsi: mpi3mr: Driver unload crashes host when enhanced logging is enabled
scsi: mpi3mr: ioctl timeout when disabling/enabling interrupt
scsi: lpfc: Avoid usage of list iterator variable after loop
scsi: lpfc: Check kzalloc() in lpfc_sli4_cgn_params_read()
scsi: ufs: mcq: qcom: Clean the return path of ufs_qcom_mcq_config_resource()
scsi: ufs: mcq: qcom: Fix passing zero to PTR_ERR
scsi: ufs: ufs-qcom: Remove impossible check
scsi: ufs: core: Add soft dependency on governor_simpleondemand
scsi: hisi_sas: Check devm_add_action() return value
scsi: qla2xxx: Add option to disable FC2 Target support
scsi: target: iscsi: Fix an error message in iscsi_check_key()
Linus Torvalds [Sat, 11 Mar 2023 04:06:49 +0000 (20:06 -0800)]
Merge tag 'block-6.3-2023-03-09' of git://git.kernel.dk/linux
Pull block fixes from Jens Axboe:
- Fix a regression in exclusive mode handling of the partition code,
introduced in this merge windoe (Yu)
- Fix for a use-after-free in BFQ (Yu)
- Add sysfs documentation for the 'hidden' attribute (Sagi)
* tag 'block-6.3-2023-03-09' of git://git.kernel.dk/linux:
block, bfq: fix uaf for 'stable_merge_bfqq'
docs: sysfs-block: document hidden sysfs entry
block: fix wrong mode for blkdev_put() from disk_scan_partitions()
Linus Torvalds [Sat, 11 Mar 2023 03:09:18 +0000 (19:09 -0800)]
Merge tag 'pull-highmem' of git://git./linux/kernel/git/viro/vfs
Pull put_and_unmap_page() helper from Al Viro:
"kmap_local_page() conversions in local filesystems keep running into
kunmap_local_page()+put_page() combinations. We can keep inventing
names for identical inline helpers, but it's getting rather
inconvenient. I've added a trivial helper to linux/highmem.h instead.
I would've held that back until the merge window, if not for the mess
it causes in tree topology - I've several branches merging from that
one, and it's only going to get worse if e.g. ext2 stuff gets picked
by Jan"
* tag 'pull-highmem' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
new helper: put_and_unmap_page()
Linus Torvalds [Sat, 11 Mar 2023 03:04:10 +0000 (19:04 -0800)]
Merge tag 'pull-fixes' of git://git./linux/kernel/git/viro/vfs
Pull misc fixes from Al Viro:
"pick_file() speculation fix + fix for alpha mis(merge,cherry-pick)
The fs/file.c one is a genuine missing speculation barrier in
pick_file() (reachable e.g. via close(2)). The alpha one is strictly
speaking not a bug fix, but only because confusion between
preempt_enable() and preempt_disable() is harmless on architecture
without CONFIG_PREEMPT.
Looks like alpha.git picked the wrong version of patch - that braino
used to be there in early versions, but it had been fixed quite a
while ago..."
* tag 'pull-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fs: prevent out-of-bounds array speculation when closing a file descriptor
alpha: fix lazy-FPU mis(merged/applied/whatnot)
Linus Torvalds [Sat, 11 Mar 2023 03:01:15 +0000 (19:01 -0800)]
Merge tag 'thermal-6.3-rc2' of git://git./linux/kernel/git/rafael/linux-pm
Pull thermal control fix from Rafael Wysocki:
"Fix a recently introduced deadlock in the int340x thermal control
driver (Srinivas Pandruvada)"
* tag 'thermal-6.3-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
thermal: intel: int340x: processor_thermal: Fix deadlock
Linus Torvalds [Fri, 10 Mar 2023 17:19:30 +0000 (09:19 -0800)]
Merge tag 'riscv-for-linus-6.3-rc2' of git://git./linux/kernel/git/riscv/linux
Pull RISC-V fixes from Palmer Dabbelt:
- RISC-V architecture-specific ELF attributes have been disabled in the
kernel builds
- A fix for a locking failure while during errata patching that
manifests on SiFive-based systems
- A fix for a KASAN failure during stack unwinding
- A fix for some lockdep failures during text patching
* tag 'riscv-for-linus-6.3-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
RISC-V: Don't check text_mutex during stop_machine
riscv: Use READ_ONCE_NOCHECK in imprecise unwinding stack mode
RISC-V: fix taking the text_mutex twice during sifive errata patching
RISC-V: Stop emitting attributes
Linus Torvalds [Fri, 10 Mar 2023 16:57:46 +0000 (08:57 -0800)]
Merge tag 'drm-fixes-2023-03-10' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"Weekly fixes.
msm and amdgpu are the vast majority of these, otherwise some
straggler misc from last week for nouveau and cirrus and a mailmap
update for a drm developer.
mailmap:
- add an entry
nouveau:
- fix system shutdown regression
- build warning fix
cirrus:
- NULL ptr deref fix
msm:
- fix invalid ptr free in syncobj cleanup
- sync GMU removal in teardown
- a5xx preemption fixes
- fix runpm imbalance
- DPU hw fixes
- stack corruption fix
- clear DSPP reservation
amdgpu:
- Misc display fixes
- UMC 8.10 fixes
- Driver unload fixes
- NBIO 7.3.0 fix
- Error checking fixes for soc15, nv, soc21 read register interface
- Fix video cap query for VCN 4.0.4
amdkfd:
- Fix return check in doorbell handling"
* tag 'drm-fixes-2023-03-10' of git://anongit.freedesktop.org/drm/drm: (42 commits)
drm/amdgpu/soc21: Add video cap query support for VCN_4_0_4
drm/amdgpu: fix error checking in amdgpu_read_mm_registers for nv
drm/amdgpu: fix error checking in amdgpu_read_mm_registers for soc21
drm/amdgpu: fix error checking in amdgpu_read_mm_registers for soc15
drm/amdgpu: Fix the warning info when removing amdgpu device
drm/amdgpu: fix return value check in kfd
drm/amd: Fix initialization mistake for NBIO 7.3.0
drm/amdgpu: Fix call trace warning and hang when removing amdgpu device
mailmap: add mailmap entries for Faith.
drm/msm: DEVFREQ_GOV_SIMPLE_ONDEMAND is no longer needed
drm/amd/display: Update clock table to include highest clock setting
drm/amd/pm: Enable ecc_info table support for smu v13_0_10
drm/amdgpu: Support umc node harvest config on umc v8_10
drm/connector: print max_requested_bpc in state debugfs
drm/display: Don't block HDR_OUTPUT_METADATA on unknown EOTF
drm/msm/dpu: clear DSPP reservations in rm release
drm/msm/disp/dpu: fix sc7280_pp base offset
drm/msm/dpu: fix stack smashing in dpu_hw_ctl_setup_blendstage
drm/msm/dpu: don't use DPU_CLK_CTRL_CURSORn for DMA SSPP clocks
drm/msm/dpu: fix clocks settings for msm8998 SSPP blocks
...