Bluetooth: LE Set Scan Parameter Command

This patch adds the parameter struct and the command complete event
handler to the LE Set Scan Parameter HCI command.

Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: Add dev_flags to struct hci_dev

This patch adds the dev_flags field to struct hci_dev. This new
flags variable should be used to define flags related to BR/EDR
and/or LE controller itself. It should be used to define flags
which represents states from the controller. The dev_flags is
cleared in case the controller sends a Reset Command Complete
Event to the host.

Also, this patch adds the HCI_LE_SCAN flag which was created to
track if the controller is performing LE scan or not. The flag
is set/cleared when the controller starts/stops scanning.

This is an initial effort to stop using hdev->flags to define
internal flags since it is exported to userspace by an ioctl.

Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: Add HCI Read Flow Control Mode function

Upstream Code Aurora function with minor trivial fixes.
Origin: git://codeaurora.org/kernel/msm.git

Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: Centralize SMP pairing failure handling

Signed-off-by: Brian Gix <bgix@codeaurora.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: Cleanup blkcipher on SMP termination

The blkcipher must be freed to avoid memory leak.

Signed-off-by: Brian Gix <bgix@codeaurora.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: Add HCI User Passkey Req Evt handling

Some MITM scenarios require handling of the User Passkey Request event,
by querying the user, and passing the response back.

Signed-off-by: Brian Gix <bgix@codeaurora.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: Add User Passkey Response handling

For some MITM protection pairing scenarios, the user is
required to enter or accept a 6 digit passkey.

Signed-off-by: Brian Gix <bgix@codeaurora.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: Add user readable debug for state changes

I did this as a part of a testing course at university, but it might be
useful upstream as well.

Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: Use queue in the device list

Use queue instead of stack discipline for device list. When processing
dev_list with list_for_each* devices will be prosessed in order they
were added (Usually BR/EDR first and AMP later).

Also output from hciconfig looks nicer :-)

Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: Differentiate LE User Pairing Responses

Low Energy (LE) pairing responses must be recognized and handled
differently from BR/EDR pairing responses. BR/EDR responses are
handled via HCI commands by the LMP layer, and LE responses are
handled by the Host.

Signed-off-by: Brian Gix <bgix@codeaurora.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: User Pairing Response restructuring

There are 4 possible User Responses to pairing requests,
and they all share the same checks and handling. This
restructures the handling of the two Confirm responses
in preperation for the second two.

Signed-off-by: Brian Gix <bgix@codeaurora.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: making enable_hs independent from L2CAP

Fixes bluetooth compiling when CONFIG_BT_L2CAP is not enabled

net/built-in.o: In function `hci_dev_open':
(.text+0xdce9a): undefined reference to `enable_hs'

Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: Add MGMT event for Passkey Entry

Signed-off-by: Brian Gix <bgix@codeaurora.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: Fix some checkpatch.pl errors and warnings

Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: Simplify __l2cap_global_chan_by_addr

Make __l2cap_global_chan_by_addr similar to other find functions.

Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: Refactor loop in l2cap_retransmit_one_frame

This make it easier to see what is the real reason for loop to exit.
skb_queue_next return valid skb or garbage, not NULL.

Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: Simplify l2cap_add_to_srej_queue

Make it easier to see what is loop break condition.
skb_queue_next return valid skb or garbage, not NULL.

Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: Fix possible NULL pointer derefence in l2cap code

Due to ERTM reliability L2CAP channel needs to be disconnected if
adding to srej list failed.

Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: Allow to set AMP type for virtual HCI

Type can be changed during re-opening device /dev/vhci.

Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: Do not set HCI_RAW when HS enabled

Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: Move scope of kernel parameter enable_hs

Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: Add MGMT opcodes for Passkey Entry

Signed-off-by: Brian Gix <bgix@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: Add HCI defines for User Passkey entry

Signed-off-by: Brian Gix <bgix@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: Pass all message parameters to mgmt_start_discovery

The mgmt_start_discovery command contains the type of discovery that
should be started so this should be passed to the start_discovery
function. This patch doesn't yet add any action depending on the type of
the requested discovery.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: Add missing cmd_complete for mgmt_load_link_keys

The command complete event was completely missing for this command.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: Create a unique mgmt error code hierarchy

The management protocol uses a single byte for error codes (aka command
status). In some places this value is directly copied from HCI and in
other a POSIX error number is used. This makes it impossible for
user-space to uniquily decipher the meaning of an error.

To solve this issue a new mgmt-specific set of error codes is added
along with a conversion table for HCI status values.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: Return success instead of EALREADY for mgmt commands

When the adapter state is already what is requested it's more friendly
to user-space to simply report success than to send a EALREADY error
message.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: Fix mgmt_pair_device imediate error responses

When possible cmd_complete should be returned instead of cmd_status
since it contains the remote address (this helps user-space track what
exactly failed).

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: Add address type to mgmt_pair_device

The kernel needs to know whether it should connect to a device over
BR/EDR or over LE. This is particularly important in the future when
dual-mode device may be connectable also over LE. It is also important
if/when we decide to move the LE advertisement cache from the kernel
into user-space. Adding the type to the mgmt command also ensures
conformance with the latest mgmt API spec.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: mgmt_stop_discovery_failed()

This patches creates mgmt_stop_discovery_failed() which removes
pending MGMT_OP_STOP_DISCOVERY commands and sends proper command
status events.

This patch also fixes the MGMT_OP_STOP_DISCOVERY command leak in
case cancel inquiry fails.

Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: Rename mgmt_inquiry_failed()

This patch renames the function mgmt_inquiry_failed() to
mgmt_start_discovery_failed(). This function is more related
to MGMT_OP_START_DISCOVERY command handling than to inquiry.
Besides, this functions will be reused by LE based discovery
procedures in case of failure.

Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: Only set ack_timer if we didn't send and ack

Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: Allow L2CAP to increase the security level

Some incomming connections needs to increase the security level by
requesting encryption for example (HID keyboard case). This change allows
the userspace to change it through setsockopt with defer_setup enabled.

Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: Rename l2cap_check_security()

rename to l2cap_chan_check_security() to make it consistent with other
l2cap_exported functions. This function will be exported in a later
commit.

Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: Add status parameter to mgmt_disconnect response

Since disconnecting may fail the status needs to be communicated to user
space. This also updates the implementation to match the latest mgmt API
specification.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: Add proper response to mgmt_remove_keys command

Since the command can fail we need to have a proper response with the
remote address and a failure status for it. This also updates it to
conform to the latest mgmt API spec.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: Fix deadlock with mgmt_pair_device

The hci_conn callbacks are called with the hci_dev lock already held so
no locking should be attempted in them.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: Add public/random LE address information to mgmt messages

It's necessary to know the distinction between public and random LE
addresses so the mgmt interface also needs to distinguish between them.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

mwifiex: prevent corruption instead of just warning

Probably we never hit this condition, but in case we do, we may as
well put a return here instead of just printing a warning message and
then corrupting memory.  The caller doesn't check the return code.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: enable SDIO multiport aggregation

By default SDIO multiport aggregation is disabled. It's useful to
get good throughput results. This patch enables it.

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: remove an unneeded NULL check

We dereference adapter in the error handling code so this needed to
be fixed.  This function is always called like:
adapter->if_ops.host_to_card(adapter, ...);
so adapter can never be NULL and I've removed the NULL check.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: remove unneeded kfree(NULL);

The previous if statement means this that pointer is NULL so there
is no need to free it.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

net/rfkill/core.c: use kstrtoul, etc

Use kstrtoul, etc instead of the now deprecated strict_strtoul, etc.

A semantic patch rule for the kstrtoul case is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@@
expression a,b;
{int,long} *c;
@@

-strict_strtoul
+kstrtoul
 (a,b,c)
// </smpl>

Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

net/mac80211/debugfs.c: use kstrtoul, etc

Use kstrtoul, etc instead of the now deprecated strict_strtoul, etc.

A semantic patch rule for the kstrtoul case is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@@
expression a,b;
{int,long} *c;
@@

-strict_strtoul
+kstrtoul
 (a,b,c)
// </smpl>

Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: implement wifi TX status

Implement the socket wifi TX status error
queue reflection in mac80211.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

nl80211: advertise socket TX status capability

The new wifi socket TX capability should be
supported by wifi drivers, let them advertise
whether they do or not.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: Also report the STA's TDLS flag via nl80211

Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcm80211: fmac: optimize chip core info management

Prepare for adding backplane interconnect type support

Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcm80211: fmac: replace private SB macros with ssb_regs version

Use SSB macros in order to clean up brcmfmac code

Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcm80211: fmac: move chip drive strength related code to sdio_chip.c

This patch is part of the abstracting chip backplane handle code
series.

Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcm80211: fmac: move chip detach function to sdio_chip.c

This patch is part of the abstracting chip backplane handle code
series.

Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcm80211: fmac: move chip reset core function to sdio_chip.c

This patch is part of the abstracting chip backplane handle code
series.

Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcm80211: fmac: abstract chip core revision function

Prepare for adding backplane interconnect type support

Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcm80211: fmac: abstract chip iscoreup function

Prepare for adding backplane interconnect type support

Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcm80211: fmac: chip attach code flow clean up

Merged brcmf_sdbrcm_chip_attach into brcmf_sdio_chip_attach
for better readability.

Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcm80211: fmac: remove duplicate regiter set in chip attach path

Same register writes have been done in brcmf_sdbrcm_probe_init
which is earlier in the same code path.

Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcm80211: fmac: move dongle gpio reset code to chip attach function

This patch is part of the abstracting chip backplane handle code
series.

Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcm80211: fmac: disable dongle arm core in bus core setup function

This will provide a better code flow that fits the logic

Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcm80211: fmac: move core disable function to sdio_chip.c

This patch is part of the abstracting chip backplane handle code
series.

Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcm80211: fmac: abstract chip buscore setup function

This patch is part of the abstracting chip backplane handle code
series.

Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Roland Vossen <rvossen@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcm80211: fmac: move bus core prep code to sdio_chip.c

This patch is part of abstracting chip backplane handle code
series.

Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Roland Vossen <rvossen@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcm80211: fmac: move chip recognition function to sdio_chip.c

Currently backplane handle code is scatterd around dhd_sdio.c which
is not good for maintenance and adding new backplane interconnect
type support. This patch and the follow up patches are going to
abstract all chip backplane control code specific for sdio bus
into this new sdio_chip.c

Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Roland Vossen <rvossen@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcm80211: fmac: remove unnecessary 4329 chip specific code

4329 with chiprev 0 can not be found on any product. The code can
be removed.

Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Roland Vossen <rvossen@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211/mac80211: allow management TX to not wait for ACK

For probe responses it can be useful to not wait for ACK to
avoid retransmissions if the station that sent the probe is
already on the next channel, so allow userspace to request
not caring about the ACK with a new nl80211 flag.

Since mac80211 needs to be updated for the new function
prototype anyway implement it right away -- it's just a
few lines of code.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: send unexpected 4addr event

Implement the cfg80211 notification but only send
one event per associated station to avoid having
tons of events if the station thinks it should be
allowed to use 4addr frames but it isn't.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211: add event for unexpected 4addr frames

The frames are used by AP/STA WDS mode, and hostapd
needs to know when such a frame was received to set
up the VLAN appropriately to allow using it.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: report OBSS beacons

If there's an interface in AP mode, OBSS beacons
are needed by hostapd/wpa_s to implement logic to
enable/disable protection etc. Report the frames
and set the capability flag.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211: allow registering to beacons

Add the ability to register to received beacon frames
to allow implementing OLBC logic in userspace. The
registration is per wiphy since there's no point in
receiving the same frame multiple times.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: support client probe

Support probing clients with null data frames
in AP mode.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

nl80211: add API to probe a client

When the AP SME in hostapd is used it wants to
probe the clients when they have been idle for
some time. Add explicit API to support this.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

nl80211: advertise device AP SME

Add the ability to advertise that the device
contains the AP SME and what features it can
support. There are currently no features in
the bitmap -- probe response offload will be
advertised by a few patches Arik is working
on now (who took over from Guy Eilam) and a
device with AP SME will typically implement
and require response offload.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: support spurious class3 event

Add support for the spurious class3 frame event
to mac80211 to enable AP w/o monitor mode.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

nl80211: allow subscribing to unexpected class3 frames

To implement AP mode without monitor interfaces we
need to be able to send a deauth to stations that
send frames without being associated. Enable this
by adding a new nl80211 event for such frames that
an application can subscribe to.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: add support for control port protocol in AP mode

This will allow us to support dynamic WEP with 802.1X
properly in mac80211 by not encrypting outgoing and
accepting unencrypted incoming frames.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: add helper to free TX skb

Drivers that need to drop a frame before it
can be transmitted will usually simply free
that frame. This is currently fine, but in
the future it'll be needed to tell mac80211
about this case, so add a new routine that
frees a TX skb.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: simplify mesh frame queue mapping and QoS

We only need to set the skb queue twice:

1. by the netdev, on local TX.
2. when forwarding a mesh frame.

We only need to set the qos header twice:

1. by mac80211, on local TX.
2. when putting a frame on the mpath->frame_queue

We also don't need the RA in order to set the proper queue mapping since
all mesh STAs are QoS, indicate this and do it once when the frame is
received. Also fixes an issue where the QoS header and queue mapping was not
set for unicast forwarded frames.

Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: check if frame is really part of this BA

There was an an implicit assumption that any QoS data frame received
from a STA/TID with an active BA session was sent to this vif as part of
a BA.  This is not true if IFF_PROMISC is enabled and the frame was
destined for a different peer, for example. Don't treat these frames as
part of a BA from the sending STA.

Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: QoS multicast frames have No Ack policy

Previously QoS multicast frames had the Normal Acknowledgment QoS
control bits set. This would cause broadcast frames to be discarded by
peers with which we have a BA session, since their sequence number would
fall outside the allowed range. Set No Ack QoS control bits on multicast
QoS frames and filter these in de-aggregation code.

Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
v2: Use proper QoS Ack Policy ctl field mask (Christian)

v3: Clean up conditional (Johannes)
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: Avoid filling up mesh preq queue with redundant requests

Don't accept redundant PREQs for a given destination. This fixes a
problem under high load:

kernel: [20386.250913] mesh_queue_preq: 235 callbacks suppressed
kernel: [20386.253335] Mesh HWMP (mesh0): PREQ node queue full
kernel: [20386.253352] Mesh HWMP (mesh0): PREQ node queue full
(...)

The 802.11s protocol has a provision to limit the rate of path requests
(PREQs) are transmitted (dot11MeshHWMPpreqMinInterval) but there was no
limit on the rate at which PREQs were being queued up.  There is a valid
reason for queuing PREQs: this way we can even out PREQ bursts.  But
queueing multiple PREQs for the same destination is useless.

Reported-by: Pedro Larbig <pedro.larbig@carhs.de>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Improve debugfs printout for stations.

Add interface address so it can be mapped to a local
interface.  Add max-ampdu and mpdu-density.

Print out the tid->baw_size

Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: verify virtual interfaces in driver API

The driver is never informed about monitor or
AP_VLAN interfaces, so whenever we pass those
to it later this is a bug. Verify we don't as
there are some cases where this could happen.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

net: add wireless TX status socket option

The 802.1X EAPOL handshake hostapd does requires
knowing whether the frame was ack'ed by the peer.
Currently, we fudge this pretty badly by not even
transmitting the frame as a normal data frame but
injecting it with radiotap and getting the status
out of radiotap monitor as well. This is rather
complex, confuses users (mon.wlan0 presence) and
doesn't work with all hardware.

To get rid of that hack, introduce a real wifi TX
status option for data frame transmissions.

This works similar to the existing TX timestamping
in that it reflects the SKB back to the socket's
error queue with a SCM_WIFI_STATUS cmsg that has
an int indicating ACK status (0/1).

Since it is possible that at some point we will
want to have TX timestamping and wifi status in a
single errqueue SKB (there's little point in not
doing that), redefine SO_EE_ORIGIN_TIMESTAMPING
to SO_EE_ORIGIN_TXSTATUS which can collect more
than just the timestamp; keep the old constant
as an alias of course. Currently the internal APIs
don't make that possible, but it wouldn't be hard
to split them up in a way that makes it possible.

Thanks to Neil Horman for helping me figure out
the functions that add the control messages.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: simplify ieee80211_work_work

Since local->tmp_channel is always NULL in one branch, some code paths
will newer be taken in that branch, so remove them.

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: remove useless brackets in ieee80211_cfg_on_oper_channel

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: remove uneeded scan_chan variable

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: preserve EOSP in QoS header

Janusz reported that the EOSP bit in mac80211 was
getting cleared all the time. I had not found this
since I tested uAPSD with a device that always set
the bit itself. Preserve the bit when building the
QoS header.

Reported-by: Janusz Dziedzic <janusz.dziedzic@gmail.com>
Tested-by: Janusz Dziedzic <janusz.dziedzic@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

nl80211: Increase maximum NL80211_ATTR_KEY_SEQ length to 16

WPI-SMS4 uses 16-octet PN field, so we need to allow longer key
sequence values to be configured.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ieee80211: Define cipher suite selector for WPI-SMS4

This value is used for WPI-SMS4 in ISO/IEC JTC 1 N 9880.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: set BSS_CHANGED_IDLE on vif reconfig

The vif might be busy while reconfiguring
(e.g. associated), so indicate BSS_CHANGED_IDLE as well.

Reported-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ipw2x00: remove unused function libipw_ratelimit_debug.

Looks like no one uses it.

Signed-off-by: Stanislav Yakovlev <stas.yakovlev@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Advertise support for TDLS

Based on a quick test, TDLS seemed to be working fine with ath9k, so
let's start advertising support for this in the driver.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

orinoco: release BSS structures returned by cfg80211_inform_bss()

The pointer returned by cfg80211_inform_bss is a referenced
struct. The orinoco driver does not need to keep the struct, so
we just release it.

Signed-off-by: David Kilroy <kilroyd@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rndis_wlan: release BSS structures returned by cfg80211_inform_bss()

Patch fixes rndis_wlan to release referenced BSS structure returned by
cfg80211_inform_bss().

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211: annotate cfg80211_inform_bss

This function returns a referenced BSS struct
(or NULL), annotate with __must_check. It seems
that a lot of drivers get this completely wrong
and leak all BSS structs as a result.

Reported-by: Adam Mikuta <Adam.Mikuta@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: handle HT PHY BSS membership selector value correctly

802.11n-2009 extends the supported rates element with a
magic value which can be used to prevent legacy stations
from joining the BSS.

However, this magic value is not a rate like the others
and the magic can simply be ignored/skipped at this late
stage.

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>---
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wireless: cleanup brcm80211 bits in drivers/net/wireless/Makefile

Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge branch 'master' of git://git./linux/kernel/git/padovan/bluetooth-next

Conflicts:
net/bluetooth/l2cap_sock.c
net/bluetooth/mgmt.c

Merge branch 'master' of git://git./linux/kernel/git/linville/wireless

Bluetooth: Remove redundant hci_dev comparisons in mgmt lookups

Now that pending commands are hci_dev specific there's no need to check
whether a command matches hci_dev when iterating through them.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: Fix consistency with u16 integer type in mgmt pending_cmd

For consistency the integer type should be u16 and not __u16.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>