Andrew Ruder [Wed, 12 Aug 2015 17:55:47 +0000 (12:55 -0500)]
pxa: Fix boot hang by avoiding vector relocation
Since commit
3ff46cc42b9d73d0 ("arm: relocate the exception vectors")
pxa does not boot anymore.
Add a specific relocate_vectors macro that skips the vector relocation,
as the pxa SoC does not provide RAM at the high vectors address
(0xFFFF0000), and (0x00000000) maps to ROM.
This allows pxa to boot again.
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Andrew Ruder <andrew.ruder@elecsyscorp.com>
Tom Rini [Mon, 24 Aug 2015 00:44:25 +0000 (20:44 -0400)]
Merge git://git.denx.de/u-boot-socfpga
Conflicts:
configs/socfpga_arria5_defconfig
configs/socfpga_cyclone5_defconfig
configs/socfpga_socrates_defconfig
Merged these by hand and re-ran savedefconfig on them.
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Mon, 24 Aug 2015 00:41:04 +0000 (20:41 -0400)]
Merge branch 'master' of git://git.denx.de/u-boot-net
Marek Vasut [Wed, 19 Aug 2015 05:46:49 +0000 (07:46 +0200)]
arm: socfpga: Fix ArriaV SoCDK PLL config
Pull out the ArriaV SoCDK clock config from ancient Altera U-Boot
"rel_socfpga_v2013.01.01_15.05.01_pr" and implant those values into
mainline to get a booting ArriaV SoCDK.
Signed-off-by: Marek Vasut <marex@denx.de>
Marek Vasut [Wed, 19 Aug 2015 05:44:39 +0000 (07:44 +0200)]
arm: socfpga: Enable ethernet on ArriaV SoCDK
Synchronise the config options with Cyclone V SoCDK and other boards.
This enables ethernet on the ArriaV SoCDK.
Signed-off-by: Marek Vasut <marex@denx.de>
Marek Vasut [Wed, 19 Aug 2015 05:43:19 +0000 (07:43 +0200)]
arm: socfpga: Fix SD/MMC boot on ArriaV SoCDK
Add the missing DT nodes, so that ArriaV SoCDK can boot from SD
card. The SD card must be in slot J5 and BSEL must be 0x5.
Signed-off-by: Marek Vasut <marex@denx.de>
Marek Vasut [Wed, 19 Aug 2015 20:25:44 +0000 (22:25 +0200)]
arm: socfpga: Fix MAINTAINERS entry for CV/AV SoCDK
Repair the maintainer entries so they match the current state of code.
Signed-off-by: Marek Vasut <marex@denx.de>
Marek Vasut [Tue, 23 Jun 2015 14:01:28 +0000 (16:01 +0200)]
arm: socfpga: Enable DWAPB GPIO driver
Enable the DWAPB GPIO driver for SoCFPGA Cyclone V and Arria V.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Marek Vasut [Mon, 10 Aug 2015 15:20:23 +0000 (17:20 +0200)]
arm: socfpga: dts: Add bank-name property to each GPIO bank
Add "bank-name" property to each GPIO bank to give it unique name.
The approach here is exactly the same as with the "regulator-name"
property for regulators.
Signed-off-by: Marek Vasut <marex@denx.de>
Marek Vasut [Tue, 23 Jun 2015 13:54:19 +0000 (15:54 +0200)]
gpio: Add DW APB GPIO driver
Add driver for the DesignWare APB GPIO IP block.
This driver is DM capable and probes from DT.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Marek Vasut [Mon, 10 Aug 2015 20:17:46 +0000 (22:17 +0200)]
arm: socfpga: Make the pinmux table const u8
Now that we're actually converting the QTS-generated header files,
we can even adjust their data types. A good candidate for this is
the pinmux table, where each entry can have value in the range of
0..3, but each element is declared as unsigned long. By changing
the type to u8, we can save over 600 Bytes from the SPL, so do it.
This patch also constifies the array.
Signed-off-by: Marek Vasut <marex@denx.de>
Marek Vasut [Mon, 10 Aug 2015 19:21:07 +0000 (21:21 +0200)]
arm: socfpga: Switch to filtered QTS files
Signed-off-by: Marek Vasut <marex@denx.de>
Marek Vasut [Mon, 10 Aug 2015 18:48:07 +0000 (20:48 +0200)]
arm: socfpga: Add qts-filter.sh script
Add script which loads the QTS-generated sources and headers and converts
them into sensible format which can be used with much more easy in mainline
U-Boot. The script also filters out macros which makes no sense anymore, so
they don't pollute namespace and waste space.
Signed-off-by: Marek Vasut <marex@denx.de>
Marek Vasut [Mon, 10 Aug 2015 19:39:52 +0000 (21:39 +0200)]
arm: socfpga: Remove AV-specific parts from CV-SoCDK
Just remove the ArriaV specific parts from the CycloneV SoCDK board
and they are no longer needed now.
Signed-off-by: Marek Vasut <marex@denx.de>
Marek Vasut [Mon, 10 Aug 2015 19:37:14 +0000 (21:37 +0200)]
arm: socfpga: Remove CV-specific parts from AV-SoCDK
Just remove the CycloneV specific parts from the ArriaV SoCDK board
and they are no longer needed now.
Signed-off-by: Marek Vasut <marex@denx.de>
Marek Vasut [Mon, 10 Aug 2015 19:24:53 +0000 (21:24 +0200)]
arm: socfpga: Split Altera socfpga into AV and CV SoCDK
The board/altera/socfpga directory is not a generic SoCFPGA machine
anymore, but instead it represents the Altera SoCDK board. To make
matters more complicated, it represents both CycloneV and ArriaV
variant.
On the other hand, nowadays, the content of this board directory is
mostly comprised of QTS-generated header files, while all the generic
code is in arch/arm/mach-socfpga already.
Thus, this patch splits the board/altera/socfpga into a separate
board directory for ArriaV SoCDK and CycloneV SoCDK, so that each
can be populated with the correct QTS-generated header files for
that particular board.
Signed-off-by: Marek Vasut <marex@denx.de>
Marek Vasut [Sun, 2 Aug 2015 19:57:57 +0000 (21:57 +0200)]
arm: socfpga: Unbind CPU type from board type
The CONFIG_TARGET_SOCFPGA_CYCLONE5 and CONFIG_TARGET_SOCFPGA_ARRIA5
selected both a board and a CPU. This is not correct as these macros
are supposed to select only board.
All would be good, if QTS-generated header files didn't check for
these macros exactly to determine if the platform is Cyclone V or
Arria V. Thus, for the sake of compatibility with not well fleshed
out header file generator, this patch makes these two macros into
a stub config option and introduces new CONFIG_TARGET_SOCFPGA_CYCLONE5_SOCDK
and CONFIG_TARGET_SOCFPGA_ARRIA5_SOCDK targets, which select the
previous stub config option.
The result is that compatibility with QTS is preserved and the new
CONFIG_TARGET_* select actual target boards.
Signed-off-by: Marek Vasut <marex@denx.de>
Marek Vasut [Sun, 2 Aug 2015 19:12:09 +0000 (21:12 +0200)]
arm: socfpga: Move wrappers into platform directory
Move the wrappers for QTS-generated files into platform directory
out of the board directory. The trick here is to add -I to CFLAGS
such that it points to the board directory in source tree and thus
the qts/ directory there is still reachable.
Signed-off-by: Marek Vasut <marex@denx.de>
Marek Vasut [Mon, 3 Aug 2015 13:32:37 +0000 (15:32 +0200)]
arm: socfpga: Do not enable gmac1 in Cyclone V dtsi
The GMAC which is enabled is purely board property, so do not enable
arbitrary GMAC in DT include files. Same goes for PHY mode, which is
again a board property. The CycloneV SoCDK does this correctly, but
SoCrates doesn't. This bug never manifested itself though, since all
the boards ever used the GMAC1 . This bug manifests itself only on
boards that utilise GMAC0.
Signed-off-by: Marek Vasut <marex@denx.de>
Marek Vasut [Sun, 2 Aug 2015 20:55:24 +0000 (22:55 +0200)]
arm: socfpga: Make the DT mmc node consistent
The socfpga_cyclone5.dtsi has an mmc0 node, socrates has mmc node.
This makes aliases not very usable, so make everything into mmc0.
Moreover, zap the useless mmc alias while at this.
Signed-off-by: Marek Vasut <marex@denx.de>
Marek Vasut [Mon, 10 Aug 2015 22:54:12 +0000 (00:54 +0200)]
arm: socfpga: Fix delay in clock manager
This code claims it needs to wait 7us, yet it uses get_timer() function
which operates with millisecond granularity. Use timer_get_us() instead,
which operates with microsecond granularity.
Signed-off-by: Marek Vasut <marex@denx.de>
Marek Vasut [Mon, 10 Aug 2015 22:49:09 +0000 (00:49 +0200)]
arm: socfpga: Fix delay in freeze controller
Based on observation, this udelay(20) was apparently too high and caused
subsequent failure to calibrate DDR when U-Boot was compiled with certain
toolchains. Lowering this delay fixed the problem.
Instead of permanently lowering the delay, calculate the correct delay
based on the original comment, that is, obtain EOSC1 frequency and use
it to calculate the precise delay.
Signed-off-by: Marek Vasut <marex@denx.de>
Marek Vasut [Mon, 10 Aug 2015 21:01:43 +0000 (23:01 +0200)]
ddr: altera: Repair uninited variable
Fix the following problem:
drivers/ddr/altera/sequencer.c: In function 'sdram_calibration_full':
drivers/ddr/altera/sequencer.c:1943:25: warning: 'found_failing_read' may be used uninitialized in this function [-Wmaybe-uninitialized]
if (found_passing_read && found_failing_read)
^
drivers/ddr/altera/sequencer.c:1803:26: note: 'found_failing_read' was declared here
u32 found_passing_read, found_failing_read, initial_failing_dtap;
^
Signed-off-by: Marek Vasut <marex@denx.de>
Marek Vasut [Mon, 10 Aug 2015 20:50:11 +0000 (22:50 +0200)]
ddr: altera: Replace float multiplication with integer one
This gem is really really rare, there was an actual float used in
the Altera DDR init code, which pulled in floating point ops from
the libgcc, just wow.
Since we don't support floating point operations the same way Linux
does not support them, replace this with an integer multiplication
and division combo. This removes some 2kiB of size from the SPL as
the floating point ops are no longer pulled in from libgcc.
This was detected by enabling CONFIG_USE_PRIVATE_LIBGCC=y , which
does not contain the floating point bits.
Signed-off-by: Marek Vasut <marex@denx.de>
Simon Glass [Wed, 19 Aug 2015 15:33:43 +0000 (09:33 -0600)]
net: Move CONFIG_E1000 options to Kconfig
Move config for the E1000 Ethernet driver to Kconfig and tidy up affected
boards.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Simon Glass [Wed, 19 Aug 2015 15:33:42 +0000 (09:33 -0600)]
Tidy up some defconfig files
Several files are out of order. This means that when the moveconfig tool
moves CONFIG options to Kconfig it generates a large diff. To avoid this,
reorder the files first.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Wed, 19 Aug 2015 15:33:41 +0000 (09:33 -0600)]
net: e1000: Add Kconfig options
Add Kconfig options in preparation for moving boards to use Kconfig.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Simon Glass [Wed, 19 Aug 2015 15:33:40 +0000 (09:33 -0600)]
net: e1000: Convert to driver model
Update this driver to support driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-on: Apalis T30 2GB on Apalis Evaluation Board
Simon Glass [Wed, 19 Aug 2015 15:33:39 +0000 (09:33 -0600)]
net: e1000: Prepare for driver model conversion
Since struct eth_device does not exist with CONFIG_DM_ETH defined, avoid
using it in the driver unless necessary. Most of the time it is better to
pass the private driver pointer anyway.
Also refactor the code so that code that the driver model implementation
will share are available in functions that can be called. Add stubs where
necessary.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-on: Apalis T30 2GB on Apalis Evaluation Board
Simon Glass [Wed, 19 Aug 2015 15:33:38 +0000 (09:33 -0600)]
net: e1000: Move #include of common.h to the C files
We cannot currently include any header files in the C files since common.h
needs to be included first, and it is in the header file. Move it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-on: Apalis T30 2GB on Apalis Evaluation Board
Michal Simek [Fri, 21 Aug 2015 06:49:48 +0000 (08:49 +0200)]
net: Return -EINTR when ctrl+c is pressed
Current behavior is that if CTRL+C is pressed command returns 0 that was
successful which is not correct behavior.
The easiest test case is "tftpboot 80000 uImage && echo yes"
and press CTRL+C. Then the second command is called which is incorrect.
Error log:
zynq-uboot> tftpb 80000 uImage && echo yes
Gem.
e000b000:7 is connected to Gem.
e000b000. Reconnecting to
Gem.
e000b000
Gem.
e000b000 Waiting for PHY auto negotiation to complete....... done
Using Gem.
e000b000 device
TFTP from server 192.168.0.102; our IP address is 192.168.0.101
Filename 'uImage'.
Load address: 0x80000
Loading: ################
Abort
yes
zynq-uboot>
This patch adds -EINTR return value when CTRL+C is pressed.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Mingkai Hu [Tue, 18 Aug 2015 21:06:26 +0000 (14:06 -0700)]
net: e1000: Support 64-bit physical address
High 32-bit address is needed when u-boot runs in 64-bit space.
Tested on armv8-based LS2085ARDB.
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Pavel Machek [Tue, 18 Aug 2015 12:34:26 +0000 (14:34 +0200)]
tftp: adjust settings to be suitable for 100Mbit ethernet
Adjust timouts and retry counts to be suitable for loaded ethernet
network. With 5 seconds timeout, 10 retries maximum, tftp is
impossible even on local network with single full-speed TCP
connection.
100msec timeout should be suitable for most networks tftp is used on,
that is local ethernets. Timeout count really needs to be way higher,
as lost packets are normal when TCP is running over the same network.
Enforce 10msec minimum.
Signed-off-by: Pavel Machek <pavel@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Wu, Josh [Wed, 19 Aug 2015 11:11:21 +0000 (19:11 +0800)]
ARM: at91: sama5: update the spi flash mapping
Also move the spi flash configurations to the at91-sama5_common.h.
Current at91 zImage size is about 3.3M, the old mapping is not
suitable. So update the spi flash map as following:
0x0 ~ 0x004000: at91bootstrap(16k)
0x04000 ~ 0x008000: u-boot env(16k)
0x08000 ~ 0x060000: u-boot(352k)
0x60000 ~ 0x06c000: dtb (48k)
0x6c000 ~ 0x400000: kernel (3M+592k)
In AT91Bootstrap, the U-Boot in spi flash also update to 0x8000, refer
to following commit in AT91Bootstrap:
3e91e54 Kconfig: fix spi flash address
So also update SPL's u-boot load address to 0x8000 in spi flash.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Wu, Josh [Wed, 19 Aug 2015 11:11:20 +0000 (19:11 +0800)]
ARM: at91: sama5: move the nandflash env config to at91-sama5_common.h
As all sama5 nandflash env configurations are same, so move them to
at91-sama5_common.h.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Wu, Josh [Wed, 19 Aug 2015 11:11:19 +0000 (19:11 +0800)]
ARM: at91: sama5d3xek: use a $dtb_name to load dtb
Since sama5d3xek boards has different type of dtb blobs, so we need to detect
the cpu type in runtime.
So we add a new variable $dtb_name. if $dtb_name is not defined, we just use
at91-${board_name}.dtb
as the $dtb_name. Otherwise, we will just load the dtb with
$dtb_name.
For sama5d3xek, we will detect cpu type and make up $dtb_name in
runtime.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Wu, Josh [Wed, 19 Aug 2015 11:11:18 +0000 (19:11 +0800)]
ARM: at91: sama5: move the sd/mmc env config to at91-sama5_common.h
As almost all sama5 sd/mmc env configurations are same, so move them to
at91-sama5_common.h.
Also define CONFIG_ENV_VARS_UBOOT_CONFIG to have the varaible: $board_name.
Then we can use 'at91-${board_name}.dtb' as the dtb name.
TODO: since sama5d3xek has different dtb name, we need to some extra
stuff to make it work on sama5d3xek boards.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Erik van Luijk [Mon, 17 Aug 2015 10:47:34 +0000 (12:47 +0200)]
arm: at91: add support for mini-box picosam9g45 board
Bootlog:
U-Boot SPL 2015.10-rc1-00452-g96a7ed1 (Aug 17 2015 - 10:32:21)
mci: setting clock 258000 Hz, block size 512
mci: setting clock 258000 Hz, block size 512
mci: setting clock 258000 Hz, block size 512
mci: setting clock
33024000 Hz, block size 512
reading u-boot.img
reading u-boot.img
U-Boot 2015.10-rc1-00452-g96a7ed1 (Aug 17 2015 - 10:32:21 +0000)
CPU: AT91SAM9G45
Crystal frequency: 12 MHz
CPU clock : 400 MHz
Master clock : 133.333 MHz
Watchdog enabled
DRAM: 256 MiB
WARNING: Caches not enabled
MMC: mci: 0
mci: setting clock 260416 Hz, block size 512
mci: setting clock 260416 Hz, block size 512
mci: setting clock 260416 Hz, block size 512
mci: setting clock
33333333 Hz, block size 512
reading uboot.env
In: serial
Out: serial
Err: serial
Net: macb0
Error: macb0 address not set.
Hit any key to stop autoboot: 0
U-Boot>
Signed-off-by: Erik van Luijk <evanluijk@interact.nl>
[add 'picosam9g45_defconfig' to MAINTAINERS]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Erik van Luijk [Thu, 13 Aug 2015 13:43:20 +0000 (15:43 +0200)]
arm: at91: pmc: replace the constant with a define in at91_pmc.h
To enable the clocks on the at91 boards a constant (0x4) is used.
This is replaced with a define in at91_pmc.h (1 << 2).
Signed-off-by: Erik van Luijk <evanluijk@interact.nl>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Erik van Luijk [Thu, 13 Aug 2015 13:43:19 +0000 (15:43 +0200)]
arm: at91: at91sam9m10g45ek/corvus remove useless chip select 1 init
On these boards the DDR is connected to a dedicated controller and not
to chip select 1 of the EBI.
Signed-off-by: Erik van Luijk <evanluijk@interact.nl>
Tested-by: Erik van Luijk <evanluijk@interact.nl>
Erik van Luijk [Thu, 13 Aug 2015 13:43:18 +0000 (15:43 +0200)]
arm: at91: mpddr: allow multiple DDR controllers
The mpddr.c depends on ATMEL_BASE_MPDDRC for the base address to configure the controller.
This cannot be used when there is more than one controller (i.e. AT91SAM9G45, AT91SAM9M10).
Signed-off-by: Erik van Luijk <evanluijk@interact.nl>
[remove 'new blank line at EOF']
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Masahiro Yamada [Thu, 20 Aug 2015 01:20:55 +0000 (10:20 +0900)]
ARM: davinci: remove support for cam_enc_4xx
This has not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Heiko Schocher <hs@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Tom Rini [Wed, 19 Aug 2015 22:04:48 +0000 (18:04 -0400)]
Merge git://git.denx.de/u-boot-usb
Marek Vasut [Wed, 12 Aug 2015 20:19:15 +0000 (22:19 +0200)]
usb: dwc2: Rename to dwc2_usb
This driver is not used only on exynos, but also on Altera SoCFPGA,
HiSilicon SoCs, RPi etc, so rename it accordingly to prevent confusion.
Signed-off-by: Marek Vasut <marex@denx.de>
Marek Vasut [Wed, 12 Aug 2015 20:19:14 +0000 (22:19 +0200)]
usb: dwc2: Add original Synopsys compat string
Add the Synopsys compatible string. This is used in SoCFPGA DT files.
Signed-off-by: Marek Vasut <marex@denx.de>
Kishon Vijay Abraham I [Wed, 19 Aug 2015 08:19:48 +0000 (13:49 +0530)]
usb: gadget: ether: populate _reset_ callback
populate _reset_ callback to the USB ethernet gadget since UDC core
expects every gadget driver to have the reset callback. This shouldn't
be needed once the ethernet gadget driver is adapted to use the
composite driver.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Kishon Vijay Abraham I [Wed, 19 Aug 2015 08:19:47 +0000 (13:49 +0530)]
usb: host: xhci-omap: invoke board_usb_cleanup in xhci_hcd_stop
xhci omap driver has board_usb_init in xhci_hcd_init but doesn't have
the corresponding cleanup function in xhci_hcd_stop.
Fix it here by invoking board_usb_cleanup() in xhci_hcd_stop().
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Kishon Vijay Abraham I [Wed, 19 Aug 2015 08:19:46 +0000 (13:49 +0530)]
usb: gadget: ether: Perform board initialization from ethernet gadget driver
Ethernet gadget driver can be used both by both SPL and u-boot. Since
usb_eth_init() is the entry point for ethernet gadget driver, perform
board initialization there. Also perform the cleanup in usb_eth_halt.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Sergey Temerkhanov [Mon, 17 Aug 2015 12:38:07 +0000 (15:38 +0300)]
usb: xhci: Fix a potential NULL pointer dereference
This patch fixes a potential NULL pointer dereference arising on
non-present/non-initialized xHCI controllers and adds some error
handling to xHCI code
Signed-off-by: Sergey Temerkhanov <s.temerkhanov@gmail.com>
Signed-off-by: Radha Mohan Chintakuntla <rchintakuntla@cavium.com>
Stefan Roese [Tue, 18 Aug 2015 07:27:18 +0000 (09:27 +0200)]
usb: spear: Add support for both SPEAr600 EHCI controllers
USB EHCI on SPEAr600 has not been tested for a while. The base controller
addresses are missing. This patch adds the defines to the header. And adds
the missing code.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Vipin Kumar <vk.vipin@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Adrian Alonso [Thu, 6 Aug 2015 20:46:03 +0000 (15:46 -0500)]
imx: usb: ehci-mx6: wait_for_bit to check reg status
Add wait_for_bit to check reg bit status and replace unbounded
loops to check usb command status
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
Adrian Alonso [Thu, 6 Aug 2015 20:43:17 +0000 (15:43 -0500)]
imx: usb: ehci-mx6: add usb support for imx7d soc
Extend ehci-mx6 usb driver to support imx7d usb
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
Adrian Alonso [Thu, 6 Aug 2015 20:43:16 +0000 (15:43 -0500)]
imx: usb: ehci-mx6: document board specific functions
Document target board specific functions
board_ehci_hcd_init - override usb phy mode
board_ehci_hcd_init - set usb vbus voltage
board_ehci_power - enables/disables usb vbus voltage
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
Adrian Alonso [Thu, 6 Aug 2015 20:43:15 +0000 (15:43 -0500)]
imx: usb: ehci-mx6: reg accessor cleanups
Cleanup read/write register access, use clr/set bits_le32
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
Michal Simek [Wed, 12 Aug 2015 10:58:54 +0000 (12:58 +0200)]
zynqmp: enable CONFIG_NET_RANDOM_ETHADDR
We have to set a MAC address to use network.
Otherwise, the tftpboot command fails with the following message:
Gem.
e000b000 Waiting for PHY auto negotiation to complete........ done
*** ERROR: `ethaddr' not set
Since commit
92ac52082140 ("net: Remove all references to
CONFIG_ETHADDR and friends"), we can not use CONFIG_ETHADDR.
The easiest way to set a MAC address is to enable
CONFIG_NET_RANDOM_ETHADDR.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Wed, 12 Aug 2015 09:25:05 +0000 (11:25 +0200)]
ARM: dts: Rename memory@0 to memory
zynq-7000.dtsi include skeleton.dtsi which contains memory node with
base address and size zero. If you add memory@0 node to the platform DTS
in final DTB there are two memory nodes and U-Boot works with the first
one (with zeros) which end up in failing in dram_init because size is
zero.
Platform memory node should rewrite default memory node setup from
skeleton.dtsi that's why platfroms needs to also use memory as node name
instead of memory@0.
Reported-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Masahiro Yamada [Fri, 17 Jul 2015 11:26:06 +0000 (20:26 +0900)]
zynq: enable CONFIG_NET_RANDOM_ETHADDR
We have to set a MAC address to use network.
Otherwise, the tftpboot command fails with the following message:
Gem.
e000b000 Waiting for PHY auto negotiation to complete........ done
*** ERROR: `ethaddr' not set
Since commit
92ac52082140 ("net: Remove all references to
CONFIG_ETHADDR and friends"), we can not use CONFIG_ETHADDR.
The easiest way to set a MAC address is to enable
CONFIG_NET_RANDOM_ETHADDR.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Mon, 3 Aug 2015 12:21:25 +0000 (14:21 +0200)]
zynq: Make CONFIG_OF_EMBED default case
Use embedded DTB to let users use u-boot instead of u-boot-dtb.bin.
And fix SPL to use this target.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Siva Durga Prasad Paladugu [Tue, 4 Aug 2015 07:33:26 +0000 (13:03 +0530)]
zynqmp: usb: Add usb dwc3 driver support for zynqmp
Added usb dwc3 driver support for zynqmp
this also supports the DFU and LTHOR to download
the linux images on to RAM and cen be booted from
those linux images.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Masahiro Yamada [Sat, 1 Aug 2015 07:39:54 +0000 (16:39 +0900)]
ARM: zynq: drop "optional" from board select in favor of ZC702
One disadvantage of commit
a26cd04920dc (arch: Make board selection
choices optional) is that Kconfig could create such an insane
.config file that no board is selected.
Rip off the "optional" again in favor of ZC702 as the default
target.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Siva Durga Prasad Paladugu [Tue, 4 Aug 2015 07:31:05 +0000 (13:01 +0530)]
board: Xilinx: zynqmp: Define checkboard() function
Define checkboard() function for zynqMP
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Mon, 3 Aug 2015 11:19:39 +0000 (13:19 +0200)]
configs: zynqmp: Enable networking by default for EP108
Enable networking for EP108 by default.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Thu, 30 Jul 2015 10:50:26 +0000 (12:50 +0200)]
ARM: zynqmp_ep: Enable ethernet for EP
Enable gem0 and setup phy addr for EP.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Wed, 5 Aug 2015 05:50:16 +0000 (07:50 +0200)]
ARM: zynqmp: Add platform specific arch_get_page_table
Based on the patch:
"armv8: caches: Added routine to set non cacheable region"
(sha1:
dad17fd51027ad02ac8f02deed186d08109d61fd)
it is necessary to add platform specific hook.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Wed, 29 Jul 2015 11:10:02 +0000 (13:10 +0200)]
zynqmp: Enable U-Boot run in EL3
Enable Secure IOU setup to enable U-Boot to run in EL3 without
setting from ATF.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Masahiro Yamada [Tue, 11 Aug 2015 22:31:55 +0000 (07:31 +0900)]
of: clean up OF_CONTROL ifdef conditionals
We have flipped CONFIG_SPL_DISABLE_OF_CONTROL. We have cleansing
devices, $(SPL_) and CONFIG_IS_ENABLED(), so we are ready to clear
away the ugly logic in include/fdtdec.h:
#ifdef CONFIG_OF_CONTROL
# if defined(CONFIG_SPL_BUILD) && !defined(SPL_OF_CONTROL)
# define OF_CONTROL 0
# else
# define OF_CONTROL 1
# endif
#else
# define OF_CONTROL 0
#endif
Now CONFIG_IS_ENABLED(OF_CONTROL) is the substitute. It refers to
CONFIG_OF_CONTROL for U-boot proper and CONFIG_SPL_OF_CONTROL for
SPL.
Also, we no longer have to cancel CONFIG_OF_CONTROL in
include/config_uncmd_spl.h and scripts/Makefile.spl.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Masahiro Yamada [Tue, 11 Aug 2015 22:31:54 +0000 (07:31 +0900)]
of: flip CONFIG_SPL_DISABLE_OF_CONTROL into CONFIG_SPL_OF_CONTROL
As we discussed a couple of times, negative CONFIG options make our
life difficult; CONFIG_SYS_NO_FLASH, CONFIG_SYS_DCACHE_OFF, ...
and here is another one.
Now, there are three boards enabling OF_CONTROL on SPL:
- socfpga_arria5_defconfig
- socfpga_cyclone5_defconfig
- socfpga_socrates_defconfig
This commit adds CONFIG_SPL_OF_CONTROL for them and deletes
CONFIG_SPL_DISABLE_OF_CONTROL from the other boards to invert
the logic.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Masahiro Yamada [Tue, 11 Aug 2015 22:31:53 +0000 (07:31 +0900)]
fdtdec: fix OF_CONTROL switch
There is no case where defined(SPL_DISABLE_OF_CONTROL) is true.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Masahiro Yamada [Tue, 11 Aug 2015 22:31:52 +0000 (07:31 +0900)]
dm: drop CONFIG_DM_DEVICE_REMOVE from uncmd list
We do not want to compile the DM remove code for SPL. Currently,
we undef it in include/config_uncmd_spl.h (for C files) and in
scripts/Makefile.uncmd_spl (for Makefiles). This is really ugly.
This commit demonstrates how we can deprecate those two files.
Use $(SPL_) for the entry in the Makfile and CONFIG_IS_ENABLED()
in C files.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Masahiro Yamada [Tue, 11 Aug 2015 22:31:51 +0000 (07:31 +0900)]
led: unify obj-$(CONFIG_LED) and obj-$(CONFIG_SPL_LED) entries
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Masahiro Yamada [Tue, 11 Aug 2015 22:31:50 +0000 (07:31 +0900)]
led: rename CONFIG_SPL_LED_SUPPORT to CONFIG_SPL_LED
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Masahiro Yamada [Tue, 11 Aug 2015 22:31:49 +0000 (07:31 +0900)]
ram: unify obj-$(CONFIG_RAM) and obj-$(CONFIG_SPL_RAM) entries
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Masahiro Yamada [Tue, 11 Aug 2015 22:31:48 +0000 (07:31 +0900)]
ram: rename CONFIG_SPL_RAM_SUPPORT to CONFIG_SPL_RAM
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Masahiro Yamada [Tue, 11 Aug 2015 22:31:47 +0000 (07:31 +0900)]
clk: unify obj-$(CONFIG_CLK) and obj-$(CONFIG_SPL_CLK) entries
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Masahiro Yamada [Tue, 11 Aug 2015 22:31:46 +0000 (07:31 +0900)]
clk: rename CONFIG_SPL_CLK_SUPPORT to CONFIG_SPL_CLK
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Masahiro Yamada [Tue, 11 Aug 2015 22:31:45 +0000 (07:31 +0900)]
dm: unify obj-$(CONFIG_DM) and obj-$(CONFIG_SPL_DM) entries
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Masahiro Yamada [Tue, 11 Aug 2015 22:31:44 +0000 (07:31 +0900)]
spl: move SPL driver entries to driver/Makefile
Just preparing for upcoming cleaning.
The board-specific linker script board/vpac270/u-boot-spl.lds
has been touched to avoid build error. It does not change the
size of spl/u-boot-spl.bin for this board, so it should be OK.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Masahiro Yamada [Tue, 11 Aug 2015 22:31:43 +0000 (07:31 +0900)]
linux/kconfig.h: add CPP macros useful for per-image config options
The previous commit introduced a useful macro used in makefiles,
in order to reference to different variables (CONFIG_... or
CONFIG_SPL_...) depending on the build context.
Per-image config option control is a PITA in C sources, too.
Here are some macros useful in C/CPP expressions.
CONFIG_IS_ENABLED(FOO) can be used as a shorthand for
(!defined(CONFIG_SPL_BUILD) && defined(CONFIG_FOO)) || \
(defined(CONFIG_SPL_BUILD) && defined(CONFIG_SPL_FOO))
For example, it is useful to describe C code as follows,
#if CONFIG_IS_ENABLED(OF_CONTROL)
(device tree code)
#else
(board file code)
#endif
The ifdef conditional above is switched by CONFIG_OF_CONTROL during
the U-Boot proper building (CONFIG_SPL_BUILD is not defined), and by
CONFIG_SPL_OF_CONTROL during SPL building (CONFIG_SPL_BUILD is
defined).
The macro can be used in C context as well, so you can also write the
equivalent code as follows:
if (CONFIG_IS_ENABLED(OF_CONTROL)) {
(device tree code)
} else {
(board file code)
}
Another useful macro is CONFIG_VALUE().
CONFIG_VALUE(FOO) is expanded into CONFIG_FOO if CONFIG_SPL_BUILD is
undefined, and into CONFIG_SPL_FOO if CONFIG_SPL_BUILD is defined.
You can write as follows:
text_base = CONFIG_VALUE(TEXT_BASE);
instead of:
#ifdef CONFIG_SPL_BUILD
text_base = CONFIG_SPL_TEXT_BASE;
#else
text_base = CONFIG_TEXT_BASE;
#endif
This commit also adds slight hacking on fixdep so that it can
output a correct list of fixed dependencies.
If the fixdep finds CONFIG_IS_ENABLED(FOO) in a source file,
we want
$(wildcard include/config/foo.h)
in the U-boot proper building context, while we want
$(wildcard include/config/spl/foo.h)
in the SPL build context.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Masahiro Yamada [Tue, 11 Aug 2015 22:31:42 +0000 (07:31 +0900)]
kbuild: add a makefile macro useful with per-image config options
Commit
e02ee2548afe ("kconfig: switch to single .config
configuration") made the configuration itself pretty simple,
instead, we lost the way to systematically enable/disable config
options for each image independently.
Our current strategy is, put entries into Makefile.spl for options
we need separate enabling, or once enable the options globally in
Kconfig and then undef them in Makefile.uncmd_spl if we do not want
to compile the features for SPL at all. Things are getting really
messy. Besides, "ifdef CONFIG_SPL_BUILD" are sprinkled everywhere
in makefiles.
This commit adds a variable to help describe makefile simpler.
$(SPL_) evaluates to "SPL_" during the SPL build, while to an empty
string during building U-boot proper.
So, you can write
obj-$(CONFIG_$(SPL_)FOO) += foo.o
instead of
ifdef CONFIG_SPL_BUILD
obj-$(CONFIG_SPL_FOO) += foo.o
else
obj-$(CONFIG_FOO) += foo.o
endif
If CONFIG_SPL_FOO does not exist in Kconfig, it is equivalent to
ifndef CONFIG_SPL_BUILD
obj-$(CONFIG_SPL_FOO) += foo.o
endif
This is the pattern we often see in our current makefiles.
To take advantage of this macro, we should prefix SPL_ for the SPL
version of the option when we need independent control between
U-boot and SPL. With this naming scheme, I hope our makefiles will
be much simplified.
It means we want to rename existing config options as follows
in the long run:
CONFIG_SPL_SERIAL_SUPPORT -> CONFIG_SPL_SERIAL
CONFIG_SPL_I2C_SUPPORT -> CONFIG_SPL_I2C
CONFIG_SPL_GPIO_SUPPORT -> CONFIG_SPL_GPIO
CONFIG_SPL_SPI_SUPPORT -> CONFIG_SPL_SPI
CONFIG_SPL_DISABLE_OF_CONTROL -> CONFIG_SPL_OF_CONTROL
(inverting the logic)
Then drivers/Makefile would be re-worked as follows:
obj-$(CONFIG_$(SPL_)SERIAL) += serial/
obj-$(CONFIG_$(SPL_)I2C) += i2c/
obj-$(CONFIG_$(SPL_)GPIO) += gpio/
obj-$(CONFIG_$(SPL_)SPI) += spi/
...
Eventually, SPL-specialized entries in Makefile.spl would go away.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Masahiro Yamada [Tue, 11 Aug 2015 22:31:41 +0000 (07:31 +0900)]
kbuild: fixdep: optimize code slightly
If the target string matches "CONFIG_", move the pointer p
forward. This saves several 7-chars adjustments.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Stephen Warren [Tue, 11 Aug 2015 04:45:14 +0000 (22:45 -0600)]
fs-test.sh: minor fixes
- Re-direct stderr into the log files, so any errors U-Boot emits are
visible in the logs. This is relevant if the "reset" shell command
attempts to report that it's not supported on the sandbox board.
- Fix test_fs_nonfs() to name the files it created differently for each
invocation. Otherwise, the logs from different tests overwrite
each-other.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Suriyan Ramasami <suriyan.r@gmail.com>
Vladimir Zapolskiy [Wed, 12 Aug 2015 17:22:13 +0000 (20:22 +0300)]
i2c: lpc32xx: correct sanity check for requested bus speed
LPC32xx has 3 I2C bus controllers, 2 of them are used as generic ones
and their parent clock is HCLK and CLK_HI/CLK_LO registers are 10 bit
wide. This means that if HCLK is 104MHz, then minimal configurable I2C
clock speed is about 51KHz.
Only USB OTG I2C bus controller CLK registers are 8 bit wide, thus in
assumption that peripheral clock is 13MHz it allows to set the minimal
bus speed about 25.5KHz.
Check for negative half clock value is removed since it is always false.
The change fixes the following problem for I2C busses 0 and 1:
=> i2c dev 0
Setting bus to 0
=> i2c speed 100000
Setting bus speed to 100000 Hz
Failure changing bus speed (-22)
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Tested-by: Sylvain Lemieux <slemieux@tycoint.com>
Vladimir Zapolskiy [Wed, 12 Aug 2015 17:32:08 +0000 (20:32 +0300)]
lpc32xx: add common USB OHCI defines for all LPC32xx boards
The change adds a number of macro definitions used by USB OHCI driver,
if CONFIG_USB_OHCI_LPC32XX is selected from a board config file.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Tested-by: Sylvain Lemieux <slemieux@tycoint.com>
Sylvain Lemieux [Thu, 13 Aug 2015 19:40:22 +0000 (15:40 -0400)]
usb: lpc32xx: add host USB driver
Incorporate USB driver from legacy LPCLinux NXP BSP.
The files taken from the legacy patch are:
- lpc32xx USB driver
- lpc3250 header file USB registers definition.
The legacy driver was updated and clean-up as part of the integration with the latest u-boot.
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Vladimir Zapolskiy <vz@mleia.com>
Sylvain Lemieux [Tue, 4 Aug 2015 21:04:41 +0000 (17:04 -0400)]
i2c: lpc32xx: add support for OTG I2C
Updated the LPC32xx I2C driver to support
the OTG I2C that is part of the USB module.
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
Acked-by: Marek Vasut <marex@denx.de>
Sylvain Lemieux [Thu, 13 Aug 2015 19:40:21 +0000 (15:40 -0400)]
nand: lpc32xx: add ECC layout for small page NAND
Incorporate ECC layout for small page NAND from legacy LPCLinux NXP BSP.
The code taken from the legacy patch is:
- lpc32xx SLC NAND driver (ECC layout for small page)
This layout is matching the lpc32xx NAND SLC Linux Kernel driver.
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
Sylvain Lemieux [Thu, 13 Aug 2015 19:40:20 +0000 (15:40 -0400)]
nand: lpc32xx: add hardware ECC support
Incorporate NAND SLC hardware ECC support from legacy LPCLinux NXP BSP.
The code taken from the legacy patch is:
- lpc32xx SLC NAND driver (hardware ECC support)
- lpc3250 header file missing SLC NAND registers definition
The legacy driver was updated and clean-up as part of the integration with the existing NAND SLC driver.
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
Tested-by: Vladimir Zapolskiy <vz@mleia.com>
Vladimir Zapolskiy [Tue, 11 Aug 2015 16:57:09 +0000 (19:57 +0300)]
lpc32xx: move common SLC NAND defines to arch/config.h
A number of LPC32xx SLC NAND defines is dictated by controller
hardware limits and OOB layout is defined by operating system, the
definitions are common for all users. Since those macro are used
in out of NAND SLC driver code (simple NAND SPL framework), they can
not be placed into the driver, therefore move them from board config
files to arch/config.h
The change also adds OOB layout details specific to small page NAND
devices taken from Linux kernel.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Tested-by: Sylvain Lemieux <slemieux@tycoint.com>
Sylvain Lemieux [Mon, 10 Aug 2015 12:16:31 +0000 (08:16 -0400)]
dma: lpc32xx: add DMA driver
Incorporate DMA driver from legacy LPCLinux NXP BSP.
The files taken from the legacy patch are:
- lpc32xx DMA driver
- lpc3250 header file DMA registers definition.
The legacy driver was updated and clean-up as part of the integration with the latest u-boot.
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Vladimir Zapolskiy <vz@mleia.com>
Tom Rini [Tue, 18 Aug 2015 12:25:24 +0000 (08:25 -0400)]
Merge branch 'master' of git://git.denx.de/u-boot-spi
Tom Rini [Tue, 18 Aug 2015 12:24:32 +0000 (08:24 -0400)]
Merge branch 'master' of git://git.denx.de/u-boot-samsung
Tom Rini [Mon, 17 Aug 2015 21:32:23 +0000 (17:32 -0400)]
Prepare v2015.10-rc2
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Mon, 17 Aug 2015 21:19:40 +0000 (17:19 -0400)]
Merge git://git.denx.de/u-boot-marvell
Simon Glass [Mon, 17 Aug 2015 15:28:44 +0000 (09:28 -0600)]
Revert "Align global_data to a 16-byte boundary"
This causes widespread breakage due to the operation of the low-level code
in crt0.S and cro0_64.S for ARM at least.
The fix is not complicated but it seems safer to revert this for now.
This reverts commit
2afddae07523f23f77acd066ad1719f53d289f98.
Signed-off-by: Simon Glass <sjg@chromium.org>
Vignesh R [Mon, 17 Aug 2015 07:59:57 +0000 (13:29 +0530)]
ARM: dra7xx_evm: Enable EDMA3 in SPL to support DMA on qspi
Enable TI_EDMA3 and SPL_DMA support, so as to reduce boot time. With
DMA enabled there is almost 3x improvement in read performance. This
helps in reducing boot time in qspiboot mode
Also add EDMA3 base address for DRA7XX and AM57XX.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Vignesh R [Mon, 17 Aug 2015 09:50:13 +0000 (15:20 +0530)]
spi: ti_qspi: Use DMA to read from qspi flash
ti_qspi uses memory map mode for faster read. Enabling DMA will increase
read speed by 3x @48MHz on DRA74 EVM.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Vignesh R [Mon, 17 Aug 2015 07:59:55 +0000 (13:29 +0530)]
dma: ti-edma3: Add helper function to support edma3 transfer
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Tom Rini [Mon, 17 Aug 2015 07:59:54 +0000 (13:29 +0530)]
sf: ops: Add spi_flash_copy_mmap function
When doing a memory mapped copy we may have DMA available and thus need
to have this copy abstracted so that the driver can do it, rather than a
simple memcpy.
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Vignesh R [Mon, 17 Aug 2015 07:59:53 +0000 (13:29 +0530)]
ARM: AM43XX: Add functions to enable and disable EDMA3 clocks
Adds functions to enable and disable edma3 clocks which can be invoked
by drivers using edma3 to control the clocks.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Vignesh R [Mon, 17 Aug 2015 07:59:52 +0000 (13:29 +0530)]
ARM: OMAP5: Add functions to enable and disable EDMA3 clocks
Adds functions to enable and disable edma3 clocks which can be invoked
by drivers using edma3 to control the clocks.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>