Nicholas Piggin [Fri, 23 Mar 2018 05:53:38 +0000 (15:53 +1000)]
powerpc/64s: Fix i-side SLB miss bad address handler saving nonvolatile GPRs
commit
52396500f97c53860164debc7d4f759077853423 upstream.
The SLB bad address handler's trap number fixup does not preserve the
low bit that indicates nonvolatile GPRs have not been saved. This
leads save_nvgprs to skip saving them, and subsequent functions and
return from interrupt will think they are saved.
This causes kernel branch-to-garbage debugging to not have correct
registers, can also cause userspace to have its registers clobbered
after a segfault.
Fixes:
f0f558b131db ("powerpc/mm: Preserve CFAR value on SLB miss caused by access to bogus address")
Cc: stable@vger.kernel.org # v4.9+
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Nicholas Piggin [Wed, 21 Mar 2018 02:22:28 +0000 (12:22 +1000)]
powerpc/64s: Fix lost pending interrupt due to race causing lost update to irq_happened
commit
ff6781fd1bb404d8a551c02c35c70cec1da17ff1 upstream.
force_external_irq_replay() can be called in the do_IRQ path with
interrupts hard enabled and soft disabled if may_hard_irq_enable() set
MSR[EE]=1. It updates local_paca->irq_happened with a load, modify,
store sequence. If a maskable interrupt hits during this sequence, it
will go to the masked handler to be marked pending in irq_happened.
This update will be lost when the interrupt returns and the store
instruction executes. This can result in unpredictable latencies,
timeouts, lockups, etc.
Fix this by ensuring hard interrupts are disabled before modifying
irq_happened.
This could cause any maskable asynchronous interrupt to get lost, but
it was noticed on P9 SMP system doing RDMA NVMe target over 100GbE,
so very high external interrupt rate and high IPI rate. The hang was
bisected down to enabling doorbell interrupts for IPIs. These provided
an interrupt type that could run at high rates in the do_IRQ path,
stressing the race.
Fixes:
1d607bb3bd60 ("powerpc/irq: Add mechanism to force a replay of interrupts")
Cc: stable@vger.kernel.org # v4.8+
Reported-by: Carol L. Soto <clsoto@us.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pierre-Yves MORDRET [Wed, 21 Mar 2018 16:48:40 +0000 (17:48 +0100)]
i2c: i2c-stm32f7: fix no check on returned setup
commit
771b7bf05339081019d22452ebcab6929372e13e upstream.
Before assigning returned setup structure check if not null
Fixes:
463a9215f3ca7600b5ff ("i2c: stm32f7: fix setup structure")
Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mike Kravetz [Wed, 28 Mar 2018 23:01:01 +0000 (16:01 -0700)]
ipc/shm.c: add split function to shm_vm_ops
commit
3d942ee079b917b24e2a0c5f18d35ac8ec9fee48 upstream.
If System V shmget/shmat operations are used to create a hugetlbfs
backed mapping, it is possible to munmap part of the mapping and split
the underlying vma such that it is not huge page aligned. This will
untimately result in the following BUG:
kernel BUG at /build/linux-jWa1Fv/linux-4.15.0/mm/hugetlb.c:3310!
Oops: Exception in kernel mode, sig: 5 [#1]
LE SMP NR_CPUS=2048 NUMA PowerNV
Modules linked in: kcm nfc af_alg caif_socket caif phonet fcrypt
CPU: 18 PID: 43243 Comm: trinity-subchil Tainted: G C E 4.15.0-10-generic #11-Ubuntu
NIP:
c00000000036e764 LR:
c00000000036ee48 CTR:
0000000000000009
REGS:
c000003fbcdcf810 TRAP: 0700 Tainted: G C E (4.15.0-10-generic)
MSR:
9000000000029033 <SF,HV,EE,ME,IR,DR,RI,LE> CR:
24002222 XER:
20040000
CFAR:
c00000000036ee44 SOFTE: 1
NIP __unmap_hugepage_range+0xa4/0x760
LR __unmap_hugepage_range_final+0x28/0x50
Call Trace:
0x7115e4e00000 (unreliable)
__unmap_hugepage_range_final+0x28/0x50
unmap_single_vma+0x11c/0x190
unmap_vmas+0x94/0x140
exit_mmap+0x9c/0x1d0
mmput+0xa8/0x1d0
do_exit+0x360/0xc80
do_group_exit+0x60/0x100
SyS_exit_group+0x24/0x30
system_call+0x58/0x6c
---[ end trace
ee88f958a1c62605 ]---
This bug was introduced by commit
31383c6865a5 ("mm, hugetlbfs:
introduce ->split() to vm_operations_struct"). A split function was
added to vm_operations_struct to determine if a mapping can be split.
This was mostly for device-dax and hugetlbfs mappings which have
specific alignment constraints.
Mappings initiated via shmget/shmat have their original vm_ops
overwritten with shm_vm_ops. shm_vm_ops functions will call back to the
original vm_ops if needed. Add such a split function to shm_vm_ops.
Link: http://lkml.kernel.org/r/20180321161314.7711-1-mike.kravetz@oracle.com
Fixes:
31383c6865a5 ("mm, hugetlbfs: introduce ->split() to vm_operations_struct")
Signed-off-by: Mike Kravetz <mike.kravetz@oracle.com>
Reported-by: Laurent Dufour <ldufour@linux.vnet.ibm.com>
Reviewed-by: Laurent Dufour <ldufour@linux.vnet.ibm.com>
Tested-by: Laurent Dufour <ldufour@linux.vnet.ibm.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Manfred Spraul <manfred@colorfullife.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Yan, Zheng [Fri, 16 Mar 2018 03:22:29 +0000 (11:22 +0800)]
ceph: only dirty ITER_IOVEC pages for direct read
commit
85784f9395987a422fa04263e7c0fb13da11eb5c upstream.
If a page is already locked, attempting to dirty it leads to a deadlock
in lock_page(). This is what currently happens to ITER_BVEC pages when
a dio-enabled loop device is backed by ceph:
$ losetup --direct-io /dev/loop0 /mnt/cephfs/img
$ xfs_io -c 'pread 0 4k' /dev/loop0
Follow other file systems and only dirty ITER_IOVEC pages.
Cc: stable@kernel.org
Signed-off-by: "Yan, Zheng" <zyan@redhat.com>
Reviewed-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Torvalds [Tue, 27 Mar 2018 01:39:07 +0000 (15:39 -1000)]
perf/hwbp: Simplify the perf-hwbp code, fix documentation
commit
f67b15037a7a50c57f72e69a6d59941ad90a0f0f upstream.
Annoyingly, modify_user_hw_breakpoint() unnecessarily complicates the
modification of a breakpoint - simplify it and remove the pointless
local variables.
Also update the stale Docbook while at it.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: <stable@vger.kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andrew Banman [Tue, 27 Mar 2018 22:09:06 +0000 (17:09 -0500)]
x86/platform/uv/BAU: Add APIC idt entry
commit
151ad17fbe5e56afa59709f41980508672c777ce upstream.
BAU uses the old alloc_initr_gate90 method to setup its interrupt. This
fails silently as the BAU vector is in the range of APIC vectors that are
registered to the spurious interrupt handler. As a consequence BAU
broadcasts are not handled, and the broadcast source CPU hangs.
Update BAU to use new idt structure.
Fixes:
dc20b2d52653 ("x86/idt: Move interrupt gate initialization to IDT code")
Signed-off-by: Andrew Banman <abanman@hpe.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Mike Travis <mike.travis@hpe.com>
Cc: Dimitri Sivanich <sivanich@hpe.com>
Cc: Russ Anderson <rja@hpe.com>
Cc: stable@vger.kernel.org
Cc: "H. Peter Anvin" <hpa@zytor.com>
Link: https://lkml.kernel.org/r/1522188546-196177-1-git-send-email-abanman@hpe.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dan Carpenter [Tue, 27 Mar 2018 13:07:52 +0000 (16:07 +0300)]
ALSA: pcm: potential uninitialized return values
commit
5607dddbfca774fb38bffadcb077fe03aa4ac5c6 upstream.
Smatch complains that "tmp" can be uninitialized if we do a zero size
write.
Fixes:
02a5d6925cd3 ("ALSA: pcm: Avoid potential races between OSS ioctls and read/write")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stefan Roese [Mon, 26 Mar 2018 14:10:21 +0000 (16:10 +0200)]
ALSA: pcm: Use dma_bytes as size parameter in dma_mmap_coherent()
commit
9066ae7ff5d89c0b5daa271e2d573540097a94fa upstream.
When trying to use the driver (e.g. aplay *.wav), the 4MiB DMA buffer
will get mmapp'ed in 16KiB chunks. But this fails with the 2nd 16KiB
area, as the page offset is outside of the VMA range (size), which is
currently used as size parameter in snd_pcm_lib_default_mmap(). By
using the DMA buffer size (dma_bytes) instead, the complete DMA buffer
can be mmapp'ed and the issue is fixed.
This issue was detected on an ARM platform (TI AM57xx) using the RME
HDSP MADI PCIe soundcard.
Fixes:
657b1989dacf ("ALSA: pcm - Use dma_mmap_coherent() if available")
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Nobutaka Okabe [Fri, 23 Mar 2018 10:49:44 +0000 (19:49 +0900)]
ALSA: usb-audio: Add native DSD support for TEAC UD-301
commit
b00214865d65100163574ba250008f182cf90869 upstream.
Add native DSD support quirk for TEAC UD-301 DAC,
by adding the PID/VID 0644:804a.
Signed-off-by: Nobutaka Okabe <nob77413@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Boris Brezillon [Tue, 27 Mar 2018 17:01:58 +0000 (19:01 +0200)]
mtd: nand: atmel: Fix get_sectorsize() function
commit
2b1b1b4ac716fd929a2d221bd4ade62263bed915 upstream.
get_sectorsize() was not using the appropriate macro to extract the
ECC sector size from the config cache, which led to buggy ECC when
using 1024 byte sectors.
Fixes:
f88fc122cc34 ("mtd: nand: Cleanup/rework the atmel_nand driver")
Cc: <stable@vger.kernel.org>
Reported-by: Olivier Schonken <olivier.schonken@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Tested-by: Olivier Schonken <olivier.schonken@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Walleij [Sat, 3 Mar 2018 22:29:03 +0000 (23:29 +0100)]
mtd: jedec_probe: Fix crash in jedec_read_mfr()
commit
87a73eb5b56fd6e07c8e499fe8608ef2d8912b82 upstream.
It turns out that the loop where we read manufacturer
jedec_read_mfd() can under some circumstances get a
CFI_MFR_CONTINUATION repeatedly, making the loop go
over all banks and eventually hit the end of the
map and crash because of an access violation:
Unable to handle kernel paging request at virtual address
c4980000
pgd = (ptrval)
[
c4980000] *pgd=
03808811, *pte=
00000000, *ppte=
00000000
Internal error: Oops: 7 [#1] PREEMPT ARM
CPU: 0 PID: 1 Comm: swapper Not tainted 4.16.0-rc1+ #150
Hardware name: Gemini (Device Tree)
PC is at jedec_probe_chip+0x6ec/0xcd0
LR is at 0x4
pc : [<
c03a2bf4>] lr : [<
00000004>] psr:
60000013
sp :
c382dd18 ip :
0000ffff fp :
00000000
r10:
c0626388 r9 :
00020000 r8 :
c0626340
r7 :
00000000 r6 :
00000001 r5 :
c3a71afc r4 :
c382dd70
r3 :
00000001 r2 :
c4900000 r1 :
00000002 r0 :
00080000
Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
Control:
0000397f Table:
00004000 DAC:
00000053
Process swapper (pid: 1, stack limit = 0x(ptrval))
Fix this by breaking the loop with a return 0 if
the offset exceeds the map size.
Fixes:
5c9c11e1c47c ("[MTD] [NOR] Add support for flash chips with ID in bank other than 0")
Cc: <stable@vger.kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Philipp Rossak [Wed, 14 Feb 2018 14:10:25 +0000 (15:10 +0100)]
ARM: dts: sun6i: a31s: bpi-m2: add missing regulators
commit
70b8d21496758dd7ff600ec9de0ee3812fac7a40 upstream.
This patch fixes a bootproblem with the Bananapi M2 board. Since there
are some regulators missing we add them right now. Those values come
from the schematic, below you can find a small overview:
* reg_aldo1: 3,3V, powers the wifi
* reg_aldo2: 2,5V, powers the IO of the RTL8211E
* reg_aldo3: 3,3V, powers the audio
* reg_dldo1: 3,0V, powers the RTL8211E
* reg_dldo2: 2,8V, powers the analog part of the csi
* reg_dldo3: 3,3V, powers misc
* reg_eldo1: 1,8V, powers the csi
* reg_ldo_io1:1,8V, powers the gpio
* reg_dc5ldo: needs to be always on
This patch updates also the vmmc-supply properties on the mmc0 and mmc2
node to use the allready existent regulators.
We can now remove the sunxi-common-regulators.dtsi include since we
don't need it anymore.
Fixes:
7daa21370075 ("ARM: dts: sunxi: Add regulators for Sinovoip BPI-M2")
Cc: <stable@vger.kernel.org>
Signed-off-by: Philipp Rossak <embed3d@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Philipp Rossak [Wed, 14 Feb 2018 14:10:24 +0000 (15:10 +0100)]
ARM: dts: sun6i: a31s: bpi-m2: improve pmic properties
commit
b23af6ad8d2f708c4c3f92dd8f82c233247ba8bf upstream.
The eldoin is supplied from the dcdc1 regulator. The N_VBUSEN pin is
connected to an external power regulator (SY6280AAC).
With this commit we update the pmic binding properties to support
those features.
Fixes:
7daa21370075 ("ARM: dts: sunxi: Add regulators for Sinovoip BPI-M2")
Cc: <stable@vger.kernel.org>
Signed-off-by: Philipp Rossak <embed3d@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fabio Estevam [Mon, 22 Jan 2018 11:20:26 +0000 (12:20 +0100)]
ARM: 8746/1: vfp: Go back to clearing vfp_current_hw_state[]
commit
1328f02005bbbaed15b9d5b7f3ab5ec9d4d5268a upstream.
Commit
384b38b66947 ("ARM: 7873/1: vfp: clear vfp_current_hw_state
for dying cpu") fixed the cpu dying notifier by clearing
vfp_current_hw_state[]. However commit
e5b61bafe704 ("arm: Convert VFP
hotplug notifiers to state machine") incorrectly used the original
vfp_force_reload() function in the cpu dying notifier.
Fix it by going back to clearing vfp_current_hw_state[].
Fixes:
e5b61bafe704 ("arm: Convert VFP hotplug notifiers to state machine")
Cc: linux-stable <stable@vger.kernel.org>
Reported-by: Kohji Okuno <okuno.kohji@jp.panasonic.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tony Lindgren [Wed, 21 Mar 2018 15:16:29 +0000 (08:16 -0700)]
ARM: OMAP: Fix SRAM W+X mapping
commit
eb85a355c3afd9379f5953cfe2df73632d14c884 upstream.
We are still using custom SRAM code for some SoCs and are not marking
the PM code mapped to SRAM as read-only and executable after we're
done. With CONFIG_DEBUG_WX=y, we will get "Found insecure W+X mapping
at address" warning.
Let's fix this issue the same way as commit
728bbe75c82f ("misc: sram:
Introduce support code for protect-exec sram type") is doing for
drivers/misc/sram-exec.c.
On omap3, we need to restore SRAM when returning from off mode after
idle, so init time configuration is not enough.
And as we no longer have users for omap_sram_push_address() we can
make it static while at it.
Note that eventually we should be using sram-exec.c for all SoCs.
Cc: stable@vger.kernel.org # v4.12+
Cc: Dave Gerlach <d-gerlach@ti.com>
Reported-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Greg Kroah-Hartman [Sat, 31 Mar 2018 16:10:43 +0000 (18:10 +0200)]
Linux 4.14.32
Julian Wiedmann [Tue, 20 Mar 2018 06:59:15 +0000 (07:59 +0100)]
s390/qeth: on channel error, reject further cmd requests
[ Upstream commit
a6c3d93963e4b333c764fde69802c3ea9eaa9d5c ]
When the IRQ handler determines that one of the cmd IO channels has
failed and schedules recovery, block any further cmd requests from
being submitted. The request would inevitably stall, and prevent the
recovery from making progress until the request times out.
This sort of error was observed after Live Guest Relocation, where
the pending IO on the READ channel intentionally gets terminated to
kick-start recovery. Simultaneously the guest executed SIOCETHTOOL,
triggering qeth to issue a QUERY CARD INFO command. The command
then stalled in the inoperabel WRITE channel.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Julian Wiedmann [Tue, 20 Mar 2018 06:59:14 +0000 (07:59 +0100)]
s390/qeth: lock read device while queueing next buffer
[ Upstream commit
17bf8c9b3d499d5168537c98b61eb7a1fcbca6c2 ]
For calling ccw_device_start(), issue_next_read() needs to hold the
device's ccwlock.
This is satisfied for the IRQ handler path (where qeth_irq() gets called
under the ccwlock), but we need explicit locking for the initial call by
the MPC initialization.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Julian Wiedmann [Tue, 20 Mar 2018 06:59:13 +0000 (07:59 +0100)]
s390/qeth: when thread completes, wake up all waiters
[ Upstream commit
1063e432bb45be209427ed3f1ca3908e4aa3c7d7 ]
qeth_wait_for_threads() is potentially called by multiple users, make
sure to notify all of them after qeth_clear_thread_running_bit()
adjusted the thread_running_mask. With no timeout, callers would
otherwise stall.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Julian Wiedmann [Tue, 20 Mar 2018 06:59:12 +0000 (07:59 +0100)]
s390/qeth: free netdevice when removing a card
[ Upstream commit
6be687395b3124f002a653c1a50b3260222b3cd7 ]
On removal, a qeth card's netdevice is currently not properly freed
because the call chain looks as follows:
qeth_core_remove_device(card)
lx_remove_device(card)
unregister_netdev(card->dev)
card->dev = NULL !!!
qeth_core_free_card(card)
if (card->dev) !!!
free_netdev(card->dev)
Fix it by free'ing the netdev straight after unregistering. This also
fixes the sysfs-driven layer switch case (qeth_dev_layer2_store()),
where the need to free the current netdevice was not considered at all.
Note that free_netdev() takes care of the netif_napi_del() for us too.
Fixes:
4a71df50047f ("qeth: new qeth device driver")
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Camelia Groza [Wed, 14 Mar 2018 13:37:32 +0000 (08:37 -0500)]
dpaa_eth: remove duplicate increment of the tx_errors counter
[ Upstream commit
82d141cd19d088ee41feafde4a6f86eeb40d93c5 ]
The tx_errors counter is incremented by the dpaa_xmit caller.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Camelia Groza [Wed, 14 Mar 2018 13:37:31 +0000 (08:37 -0500)]
dpaa_eth: increment the RX dropped counter when needed
[ Upstream commit
e4d1b37c17d000a3da9368a3e260fb9ea4927c25 ]
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Camelia Groza [Wed, 14 Mar 2018 13:37:30 +0000 (08:37 -0500)]
dpaa_eth: remove duplicate initialization
[ Upstream commit
565186362b73226a288830abe595f05f0cec0bbc ]
The fd_format has already been initialized at this point.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Madalin Bucur [Wed, 14 Mar 2018 13:37:29 +0000 (08:37 -0500)]
dpaa_eth: fix error in dpaa_remove()
[ Upstream commit
88075256ee817041d68c2387f29065b5cb2b342a ]
The recent changes that make the driver probing compatible with DSA
were not propagated in the dpa_remove() function, breaking the
module unload function. Using the proper device to address the issue.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Madalin Bucur [Wed, 14 Mar 2018 13:37:28 +0000 (08:37 -0500)]
soc/fsl/qbman: fix issue in qman_delete_cgr_safe()
[ Upstream commit
96f413f47677366e0ae03797409bfcc4151dbf9e ]
The wait_for_completion() call in qman_delete_cgr_safe()
was triggering a scheduling while atomic bug, replacing the
kthread with a smp_call_function_single() call to fix it.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: Roy Pledge <roy.pledge@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Arkadi Sharshevsky [Thu, 8 Mar 2018 10:42:10 +0000 (12:42 +0200)]
team: Fix double free in error path
[ Upstream commit
cbcc607e18422555db569b593608aec26111cb0b ]
The __send_and_alloc_skb() receives a skb ptr as a parameter but in
case it fails the skb is not valid:
- Send failed and released the skb internally.
- Allocation failed.
The current code tries to release the skb in case of failure which
causes redundant freeing.
Fixes:
9b00cf2d1024 ("team: implement multipart netlink messages for options transfers")
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Vinicius Costa Gomes [Wed, 14 Mar 2018 20:32:09 +0000 (13:32 -0700)]
skbuff: Fix not waking applications when errors are enqueued
[ Upstream commit
6e5d58fdc9bedd0255a8781b258f10bbdc63e975 ]
When errors are enqueued to the error queue via sock_queue_err_skb()
function, it is possible that the waiting application is not notified.
Calling 'sk->sk_data_ready()' would not notify applications that
selected only POLLERR events in poll() (for example).
Fixes:
1da177e4c3f4 ("Linux-2.6.12-rc2")
Reported-by: Randy E. Witt <randy.e.witt@intel.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Michal Kalderon [Wed, 14 Mar 2018 12:56:53 +0000 (14:56 +0200)]
qede: Fix qedr link update
[ Upstream commit
4609adc27175839408359822523de7247d56c87f ]
Link updates were not reported to qedr correctly.
Leading to cases where a link could be down, but qedr
would see it as up.
In addition, once qede was loaded, link state would be up,
regardless of the actual link state.
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Florian Fainelli [Tue, 13 Mar 2018 21:45:07 +0000 (14:45 -0700)]
net: systemport: Rewrite __bcm_sysport_tx_reclaim()
[ Upstream commit
484d802d0f2f29c335563fcac2a8facf174a1bbc ]
There is no need for complex checking between the last consumed index
and current consumed index, a simple subtraction will do.
This also eliminates the possibility of a permanent transmit queue stall
under the following conditions:
- one CPU bursts ring->size worth of traffic (up to 256 buffers), to the
point where we run out of free descriptors, so we stop the transmit
queue at the end of bcm_sysport_xmit()
- because of our locking, we have the transmit process disable
interrupts which means we can be blocking the TX reclamation process
- when TX reclamation finally runs, we will be computing the difference
between ring->c_index (last consumed index by SW) and what the HW
reports through its register
- this register is masked with (ring->size - 1) = 0xff, which will lead
to stripping the upper bits of the index (register is 16-bits wide)
- we will be computing last_tx_cn as 0, which means there is no work to
be done, and we never wake-up the transmit queue, leaving it
permanently disabled
A practical example is e.g: ring->c_index aka last_c_index = 12, we
pushed 256 entries, HW consumer index = 268, we mask it with 0xff = 12,
so last_tx_cn == 0, nothing happens.
Fixes:
80105befdb4b ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
David Ahern [Fri, 16 Feb 2018 19:03:03 +0000 (11:03 -0800)]
net: Only honor ifindex in IP_PKTINFO if non-0
[ Upstream commit
2cbb4ea7de167b02ffa63e9cdfdb07a7e7094615 ]
Only allow ifindex from IP_PKTINFO to override SO_BINDTODEVICE settings
if the index is actually set in the message.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Nicolas Dichtel [Wed, 14 Mar 2018 20:10:23 +0000 (21:10 +0100)]
netlink: avoid a double skb free in genlmsg_mcast()
[ Upstream commit
02a2385f37a7c6594c9d89b64c4a1451276f08eb ]
nlmsg_multicast() consumes always the skb, thus the original skb must be
freed only when this function is called with a clone.
Fixes:
cb9f7a9a5c96 ("netlink: ensure to loop over all netns in genlmsg_multicast_allns()")
Reported-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Arvind Yadav [Tue, 13 Mar 2018 15:50:06 +0000 (16:50 +0100)]
net/iucv: Free memory obtained by kzalloc
[ Upstream commit
fa6a91e9b907231d2e38ea5ed89c537b3525df3d ]
Free memory by calling put_device(), if afiucv_iucv_init is not
successful.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Florian Fainelli [Sun, 18 Mar 2018 19:49:51 +0000 (12:49 -0700)]
net: fec: Fix unbalanced PM runtime calls
[ Upstream commit
a069215cf5985f3aa1bba550264907d6bd05c5f7 ]
When unbinding/removing the driver, we will run into the following warnings:
[ 259.655198] fec
400d1000.ethernet:
400d1000.ethernet supply phy not found, using dummy regulator
[ 259.665065] fec
400d1000.ethernet: Unbalanced pm_runtime_enable!
[ 259.672770] fec
400d1000.ethernet (unnamed net_device) (uninitialized): Invalid MAC address: 00:00:00:00:00:00
[ 259.683062] fec
400d1000.ethernet (unnamed net_device) (uninitialized): Using random MAC address: f2:3e:93:b7:29:c1
[ 259.696239] libphy: fec_enet_mii_bus: probed
Avoid these warnings by balancing the runtime PM calls during fec_drv_remove().
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SZ Lin (林上智) [Thu, 15 Mar 2018 16:56:01 +0000 (00:56 +0800)]
net: ethernet: ti: cpsw: add check for in-band mode setting with RGMII PHY interface
[ Upstream commit
f9db50691db4a7d860fce985f080bb3fc23a7ede ]
According to AM335x TRM[1] 14.3.6.2, AM437x TRM[2] 15.3.6.2 and
DRA7 TRM[3] 24.11.4.8.7.3.3, in-band mode in EXT_EN(bit18) register is only
available when PHY is configured in RGMII mode with 10Mbps speed. It will
cause some networking issues without RGMII mode, such as carrier sense
errors and low throughput. TI also mentioned this issue in their forum[4].
This patch adds the check mechanism for PHY interface with RGMII interface
type, the in-band mode can only be set in RGMII mode with 10Mbps speed.
References:
[1]: https://www.ti.com/lit/ug/spruh73p/spruh73p.pdf
[2]: http://www.ti.com/lit/ug/spruhl7h/spruhl7h.pdf
[3]: http://www.ti.com/lit/ug/spruic2b/spruic2b.pdf
[4]: https://e2e.ti.com/support/arm/sitara_arm/f/791/p/640765/2392155
Suggested-by: Holsety Chen (陳憲輝) <Holsety.Chen@moxa.com>
Signed-off-by: SZ Lin (林上智) <sz.lin@moxa.com>
Signed-off-by: Schuyler Patton <spatton@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Christophe JAILLET [Sun, 18 Mar 2018 22:59:36 +0000 (23:59 +0100)]
net: ethernet: arc: Fix a potential memory leak if an optional regulator is deferred
[ Upstream commit
00777fac28ba3e126b9e63e789a613e8bd2cab25 ]
If the optional regulator is deferred, we must release some resources.
They will be re-allocated when the probe function will be called again.
Fixes:
6eacf31139bf ("ethernet: arc: Add support for Rockchip SoC layer device tree bindings")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eric Dumazet [Tue, 6 Mar 2018 15:54:53 +0000 (07:54 -0800)]
l2tp: do not accept arbitrary sockets
[ Upstream commit
17cfe79a65f98abe535261856c5aef14f306dff7 ]
syzkaller found an issue caused by lack of sufficient checks
in l2tp_tunnel_create()
RAW sockets can not be considered as UDP ones for instance.
In another patch, we shall replace all pr_err() by less intrusive
pr_debug() so that syzkaller can find other bugs faster.
Acked-by: Guillaume Nault <g.nault@alphalink.fr>
Acked-by: James Chapman <jchapman@katalix.com>
==================================================================
BUG: KASAN: slab-out-of-bounds in setup_udp_tunnel_sock+0x3ee/0x5f0 net/ipv4/udp_tunnel.c:69
dst_release: dst:
00000000d53d0d0f refcnt:-1
Write of size 1 at addr
ffff8801d013b798 by task syz-executor3/6242
CPU: 1 PID: 6242 Comm: syz-executor3 Not tainted 4.16.0-rc2+ #253
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:17 [inline]
dump_stack+0x194/0x24d lib/dump_stack.c:53
print_address_description+0x73/0x250 mm/kasan/report.c:256
kasan_report_error mm/kasan/report.c:354 [inline]
kasan_report+0x23b/0x360 mm/kasan/report.c:412
__asan_report_store1_noabort+0x17/0x20 mm/kasan/report.c:435
setup_udp_tunnel_sock+0x3ee/0x5f0 net/ipv4/udp_tunnel.c:69
l2tp_tunnel_create+0x1354/0x17f0 net/l2tp/l2tp_core.c:1596
pppol2tp_connect+0x14b1/0x1dd0 net/l2tp/l2tp_ppp.c:707
SYSC_connect+0x213/0x4a0 net/socket.c:1640
SyS_connect+0x24/0x30 net/socket.c:1621
do_syscall_64+0x280/0x940 arch/x86/entry/common.c:287
entry_SYSCALL_64_after_hwframe+0x42/0xb7
Fixes:
fd558d186df2 ("l2tp: Split pppol2tp patch into separate l2tp and ppp parts")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Lorenzo Bianconi [Thu, 8 Mar 2018 16:00:02 +0000 (17:00 +0100)]
ipv6: fix access to non-linear packet in ndisc_fill_redirect_hdr_option()
[ Upstream commit
9f62c15f28b0d1d746734666d88a79f08ba1e43e ]
Fix the following slab-out-of-bounds kasan report in
ndisc_fill_redirect_hdr_option when the incoming ipv6 packet is not
linear and the accessed data are not in the linear data region of orig_skb.
[ 1503.122508] ==================================================================
[ 1503.122832] BUG: KASAN: slab-out-of-bounds in ndisc_send_redirect+0x94e/0x990
[ 1503.123036] Read of size 1184 at addr
ffff8800298ab6b0 by task netperf/1932
[ 1503.123220] CPU: 0 PID: 1932 Comm: netperf Not tainted 4.16.0-rc2+ #124
[ 1503.123347] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.10.2-2.fc27 04/01/2014
[ 1503.123527] Call Trace:
[ 1503.123579] <IRQ>
[ 1503.123638] print_address_description+0x6e/0x280
[ 1503.123849] kasan_report+0x233/0x350
[ 1503.123946] memcpy+0x1f/0x50
[ 1503.124037] ndisc_send_redirect+0x94e/0x990
[ 1503.125150] ip6_forward+0x1242/0x13b0
[...]
[ 1503.153890] Allocated by task 1932:
[ 1503.153982] kasan_kmalloc+0x9f/0xd0
[ 1503.154074] __kmalloc_track_caller+0xb5/0x160
[ 1503.154198] __kmalloc_reserve.isra.41+0x24/0x70
[ 1503.154324] __alloc_skb+0x130/0x3e0
[ 1503.154415] sctp_packet_transmit+0x21a/0x1810
[ 1503.154533] sctp_outq_flush+0xc14/0x1db0
[ 1503.154624] sctp_do_sm+0x34e/0x2740
[ 1503.154715] sctp_primitive_SEND+0x57/0x70
[ 1503.154807] sctp_sendmsg+0xaa6/0x1b10
[ 1503.154897] sock_sendmsg+0x68/0x80
[ 1503.154987] ___sys_sendmsg+0x431/0x4b0
[ 1503.155078] __sys_sendmsg+0xa4/0x130
[ 1503.155168] do_syscall_64+0x171/0x3f0
[ 1503.155259] entry_SYSCALL_64_after_hwframe+0x42/0xb7
[ 1503.155436] Freed by task 1932:
[ 1503.155527] __kasan_slab_free+0x134/0x180
[ 1503.155618] kfree+0xbc/0x180
[ 1503.155709] skb_release_data+0x27f/0x2c0
[ 1503.155800] consume_skb+0x94/0xe0
[ 1503.155889] sctp_chunk_put+0x1aa/0x1f0
[ 1503.155979] sctp_inq_pop+0x2f8/0x6e0
[ 1503.156070] sctp_assoc_bh_rcv+0x6a/0x230
[ 1503.156164] sctp_inq_push+0x117/0x150
[ 1503.156255] sctp_backlog_rcv+0xdf/0x4a0
[ 1503.156346] __release_sock+0x142/0x250
[ 1503.156436] release_sock+0x80/0x180
[ 1503.156526] sctp_sendmsg+0xbb0/0x1b10
[ 1503.156617] sock_sendmsg+0x68/0x80
[ 1503.156708] ___sys_sendmsg+0x431/0x4b0
[ 1503.156799] __sys_sendmsg+0xa4/0x130
[ 1503.156889] do_syscall_64+0x171/0x3f0
[ 1503.156980] entry_SYSCALL_64_after_hwframe+0x42/0xb7
[ 1503.157158] The buggy address belongs to the object at
ffff8800298ab600
which belongs to the cache kmalloc-1024 of size 1024
[ 1503.157444] The buggy address is located 176 bytes inside of
1024-byte region [
ffff8800298ab600,
ffff8800298aba00)
[ 1503.157702] The buggy address belongs to the page:
[ 1503.157820] page:
ffffea0000a62a00 count:1 mapcount:0 mapping:
0000000000000000 index:0x0 compound_mapcount: 0
[ 1503.158053] flags: 0x4000000000008100(slab|head)
[ 1503.158171] raw:
4000000000008100 0000000000000000 0000000000000000 00000001800e000e
[ 1503.158350] raw:
dead000000000100 dead000000000200 ffff880036002600 0000000000000000
[ 1503.158523] page dumped because: kasan: bad access detected
[ 1503.158698] Memory state around the buggy address:
[ 1503.158816]
ffff8800298ab900: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 1503.158988]
ffff8800298ab980: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 1503.159165] >
ffff8800298aba00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 1503.159338] ^
[ 1503.159436]
ffff8800298aba80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ 1503.159610]
ffff8800298abb00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ 1503.159785] ==================================================================
[ 1503.159964] Disabling lock debugging due to kernel taint
The test scenario to trigger the issue consists of 4 devices:
- H0: data sender, connected to LAN0
- H1: data receiver, connected to LAN1
- GW0 and GW1: routers between LAN0 and LAN1. Both of them have an
ethernet connection on LAN0 and LAN1
On H{0,1} set GW0 as default gateway while on GW0 set GW1 as next hop for
data from LAN0 to LAN1.
Moreover create an ip6ip6 tunnel between H0 and H1 and send 3 concurrent
data streams (TCP/UDP/SCTP) from H0 to H1 through ip6ip6 tunnel (send
buffer size is set to 16K). While data streams are active flush the route
cache on HA multiple times.
I have not been able to identify a given commit that introduced the issue
since, using the reproducer described above, the kasan report has been
triggered from 4.14 and I have not gone back further.
Reported-by: Jianlin Shi <jishi@redhat.com>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alexey Kodanev [Tue, 6 Mar 2018 19:57:01 +0000 (22:57 +0300)]
dccp: check sk for closed state in dccp_sendmsg()
[ Upstream commit
67f93df79aeefc3add4e4b31a752600f834236e2 ]
dccp_disconnect() sets 'dp->dccps_hc_tx_ccid' tx handler to NULL,
therefore if DCCP socket is disconnected and dccp_sendmsg() is
called after it, it will cause a NULL pointer dereference in
dccp_write_xmit().
This crash and the reproducer was reported by syzbot. Looks like
it is reproduced if commit
69c64866ce07 ("dccp: CVE-2017-8824:
use-after-free in DCCP code") is applied.
Reported-by: syzbot+f99ab3887ab65d70f816@syzkaller.appspotmail.com
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kirill Tkhai [Tue, 6 Mar 2018 15:46:39 +0000 (18:46 +0300)]
net: Fix hlist corruptions in inet_evict_bucket()
[ Upstream commit
a560002437d3646dafccecb1bf32d1685112ddda ]
inet_evict_bucket() iterates global list, and
several tasks may call it in parallel. All of
them hash the same fq->list_evictor to different
lists, which leads to list corruption.
This patch makes fq be hashed to expired list
only if this has not been made yet by another
task. Since inet_frag_alloc() allocates fq
using kmem_cache_zalloc(), we may rely on
list_evictor is initially unhashed.
The problem seems to exist before async
pernet_operations, as there was possible to have
exit method to be executed in parallel with
inet_frags::frags_work, so I add two Fixes tags.
This also may go to stable.
Fixes:
d1fe19444d82 "inet: frag: don't re-use chainlist for evictor"
Fixes:
f84c6821aa54 "net: Convert pernet_subsys, registered from inet_init()"
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eric Dumazet [Wed, 14 Mar 2018 16:04:16 +0000 (09:04 -0700)]
net: use skb_to_full_sk() in skb_update_prio()
[ Upstream commit
4dcb31d4649df36297296b819437709f5407059c ]
Andrei Vagin reported a KASAN: slab-out-of-bounds error in
skb_update_prio()
Since SYNACK might be attached to a request socket, we need to
get back to the listener socket.
Since this listener is manipulated without locks, add const
qualifiers to sock_cgroup_prioidx() so that the const can also
be used in skb_update_prio()
Also add the const qualifier to sock_cgroup_classid() for consistency.
Fixes:
ca6fb0651883 ("tcp: attach SYNACK messages to request sockets instead of listener")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Andrei Vagin <avagin@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eric Dumazet [Mon, 5 Mar 2018 16:51:03 +0000 (08:51 -0800)]
ieee802154: 6lowpan: fix possible NULL deref in lowpan_device_event()
[ Upstream commit
ca0edb131bdf1e6beaeb2b8289fd6b374b74147d ]
A tun device type can trivially be set to arbitrary value using
TUNSETLINK ioctl().
Therefore, lowpan_device_event() must really check that ieee802154_ptr
is not NULL.
Fixes:
2c88b5283f60d ("ieee802154: 6lowpan: remove check on null")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Alexander Aring <alex.aring@gmail.com>
Cc: Stefan Schmidt <stefan@osg.samsung.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Acked-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alexey Kodanev [Mon, 5 Mar 2018 17:52:54 +0000 (20:52 +0300)]
sch_netem: fix skb leak in netem_enqueue()
[ Upstream commit
35d889d10b649fda66121891ec05eca88150059d ]
When we exceed current packets limit and we have more than one
segment in the list returned by skb_gso_segment(), netem drops
only the first one, skipping the rest, hence kmemleak reports:
unreferenced object 0xffff880b5d23b600 (size 1024):
comm "softirq", pid 0, jiffies
4384527763 (age 2770.629s)
hex dump (first 32 bytes):
00 80 23 5d 0b 88 ff ff 00 00 00 00 00 00 00 00 ..#]............
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<
00000000d8a19b9d>] __alloc_skb+0xc9/0x520
[<
000000001709b32f>] skb_segment+0x8c8/0x3710
[<
00000000c7b9bb88>] tcp_gso_segment+0x331/0x1830
[<
00000000c921cba1>] inet_gso_segment+0x476/0x1370
[<
000000008b762dd4>] skb_mac_gso_segment+0x1f9/0x510
[<
000000002182660a>] __skb_gso_segment+0x1dd/0x620
[<
00000000412651b9>] netem_enqueue+0x1536/0x2590 [sch_netem]
[<
0000000005d3b2a9>] __dev_queue_xmit+0x1167/0x2120
[<
00000000fc5f7327>] ip_finish_output2+0x998/0xf00
[<
00000000d309e9d3>] ip_output+0x1aa/0x2c0
[<
000000007ecbd3a4>] tcp_transmit_skb+0x18db/0x3670
[<
0000000042d2a45f>] tcp_write_xmit+0x4d4/0x58c0
[<
0000000056a44199>] tcp_tasklet_func+0x3d9/0x540
[<
0000000013d06d02>] tasklet_action+0x1ca/0x250
[<
00000000fcde0b8b>] __do_softirq+0x1b4/0x5a3
[<
00000000e7ed027c>] irq_exit+0x1e2/0x210
Fix it by adding the rest of the segments, if any, to skb 'to_free'
list. Add new __qdisc_drop_all() and qdisc_drop_all() functions
because they can be useful in the future if we need to drop segmented
GSO packets in other places.
Fixes:
6071bd1aa13e ("netem: Segment GSO packets on enqueue")
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tom Herbert [Tue, 13 Mar 2018 19:01:43 +0000 (12:01 -0700)]
kcm: lock lower socket in kcm_attach
[ Upstream commit
2cc683e88c0c993ac3721d9b702cb0630abe2879 ]
Need to lock lower socket in order to provide mutual exclusion
with kcm_unattach.
v2: Add Reported-by for syzbot
Fixes:
ab7ac4eb9832e32a09f4e804 ("kcm: Kernel Connection Multiplexor module")
Reported-by: syzbot+ea75c0ffcd353d32515f064aaebefc5279e6161e@syzkaller.appspotmail.com
Signed-off-by: Tom Herbert <tom@quantonium.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Paul Blakey [Sun, 4 Mar 2018 15:29:48 +0000 (17:29 +0200)]
rhashtable: Fix rhlist duplicates insertion
[ Upstream commit
d3dcf8eb615537526bd42ff27a081d46d337816e ]
When inserting duplicate objects (those with the same key),
current rhlist implementation messes up the chain pointers by
updating the bucket pointer instead of prev next pointer to the
newly inserted node. This causes missing elements on removal and
travesal.
Fix that by properly updating pprev pointer to point to
the correct rhash_head next pointer.
Issue: 1241076
Change-Id: I86b2c140bcb4aeb10b70a72a267ff590bb2b17e7
Fixes:
ca26893f05e8 ('rhashtable: Add rhlist interface')
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Guillaume Nault [Tue, 20 Mar 2018 15:49:26 +0000 (16:49 +0100)]
ppp: avoid loop in xmit recursion detection code
[ Upstream commit
6d066734e9f09cdea4a3b9cb76136db3f29cfb02 ]
We already detect situations where a PPP channel sends packets back to
its upper PPP device. While this is enough to avoid deadlocking on xmit
locks, this doesn't prevent packets from looping between the channel
and the unit.
The problem is that ppp_start_xmit() enqueues packets in ppp->file.xq
before checking for xmit recursion. Therefore, __ppp_xmit_process()
might dequeue a packet from ppp->file.xq and send it on the channel
which, in turn, loops it back on the unit. Then ppp_start_xmit()
queues the packet back to ppp->file.xq and __ppp_xmit_process() picks
it up and sends it again through the channel. Therefore, the packet
will loop between __ppp_xmit_process() and ppp_start_xmit() until some
other part of the xmit path drops it.
For L2TP, we rapidly fill the skb's headroom and pppol2tp_xmit() drops
the packet after a few iterations. But PPTP reallocates the headroom
if necessary, letting the loop run and exhaust the machine resources
(as reported in https://bugzilla.kernel.org/show_bug.cgi?id=199109).
Fix this by letting __ppp_xmit_process() enqueue the skb to
ppp->file.xq, so that we can check for recursion before adding it to
the queue. Now ppp_xmit_process() can drop the packet when recursion is
detected.
__ppp_channel_push() is a bit special. It calls __ppp_xmit_process()
without having any actual packet to send. This is used by
ppp_output_wakeup() to re-enable transmission on the parent unit (for
implementations like ppp_async.c, where the .start_xmit() function
might not consume the skb, leaving it in ppp->xmit_pending and
disabling transmission).
Therefore, __ppp_xmit_process() needs to handle the case where skb is
NULL, dequeuing as many packets as possible from ppp->file.xq.
Reported-by: xu heng <xuheng333@zoho.com>
Fixes:
55454a565836 ("ppp: avoid dealock on recursive xmit")
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Roman Mashak [Mon, 12 Mar 2018 20:20:58 +0000 (16:20 -0400)]
net sched actions: return explicit error when tunnel_key mode is not specified
[ Upstream commit
51d4740f88affd85d49c04e3c9cd129c0e33bcb9 ]
If set/unset mode of the tunnel_key action is not provided, ->init() still
returns 0, and the caller proceeds with bogus 'struct tc_action *' object,
this results in crash:
% tc actions add action tunnel_key src_ip 1.1.1.1 dst_ip 2.2.2.1 id 7 index 1
[ 35.805515] general protection fault: 0000 [#1] SMP PTI
[ 35.806161] Modules linked in: act_tunnel_key kvm_intel kvm irqbypass
crct10dif_pclmul crc32_pclmul ghash_clmulni_intel pcbc aesni_intel aes_x86_64
crypto_simd glue_helper cryptd serio_raw
[ 35.808233] CPU: 1 PID: 428 Comm: tc Not tainted 4.16.0-rc4+ #286
[ 35.808929] RIP: 0010:tcf_action_init+0x90/0x190
[ 35.809457] RSP: 0018:
ffffb8edc068b9a0 EFLAGS:
00010206
[ 35.810053] RAX:
1320c000000a0003 RBX:
0000000000000001 RCX:
0000000000000000
[ 35.810866] RDX:
0000000000000070 RSI:
0000000000007965 RDI:
ffffb8edc068b910
[ 35.811660] RBP:
ffffb8edc068b9d0 R08:
0000000000000000 R09:
ffffb8edc068b808
[ 35.812463] R10:
ffffffffc02bf040 R11:
0000000000000040 R12:
ffffb8edc068bb38
[ 35.813235] R13:
0000000000000000 R14:
0000000000000000 R15:
ffffb8edc068b910
[ 35.814006] FS:
00007f3d0d8556c0(0000) GS:
ffff91d1dbc40000(0000)
knlGS:
0000000000000000
[ 35.814881] CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
[ 35.815540] CR2:
000000000043f720 CR3:
0000000019248001 CR4:
00000000001606a0
[ 35.816457] Call Trace:
[ 35.817158] tc_ctl_action+0x11a/0x220
[ 35.817795] rtnetlink_rcv_msg+0x23d/0x2e0
[ 35.818457] ? __slab_alloc+0x1c/0x30
[ 35.819079] ? __kmalloc_node_track_caller+0xb1/0x2b0
[ 35.819544] ? rtnl_calcit.isra.30+0xe0/0xe0
[ 35.820231] netlink_rcv_skb+0xce/0x100
[ 35.820744] netlink_unicast+0x164/0x220
[ 35.821500] netlink_sendmsg+0x293/0x370
[ 35.822040] sock_sendmsg+0x30/0x40
[ 35.822508] ___sys_sendmsg+0x2c5/0x2e0
[ 35.823149] ? pagecache_get_page+0x27/0x220
[ 35.823714] ? filemap_fault+0xa2/0x640
[ 35.824423] ? page_add_file_rmap+0x108/0x200
[ 35.825065] ? alloc_set_pte+0x2aa/0x530
[ 35.825585] ? finish_fault+0x4e/0x70
[ 35.826140] ? __handle_mm_fault+0xbc1/0x10d0
[ 35.826723] ? __sys_sendmsg+0x41/0x70
[ 35.827230] __sys_sendmsg+0x41/0x70
[ 35.827710] do_syscall_64+0x68/0x120
[ 35.828195] entry_SYSCALL_64_after_hwframe+0x3d/0xa2
[ 35.828859] RIP: 0033:0x7f3d0ca4da67
[ 35.829331] RSP: 002b:
00007ffc9f284338 EFLAGS:
00000246 ORIG_RAX:
000000000000002e
[ 35.830304] RAX:
ffffffffffffffda RBX:
00007ffc9f284460 RCX:
00007f3d0ca4da67
[ 35.831247] RDX:
0000000000000000 RSI:
00007ffc9f2843b0 RDI:
0000000000000003
[ 35.832167] RBP:
000000005aa6a7a9 R08:
0000000000000001 R09:
0000000000000000
[ 35.833075] R10:
00000000000005f1 R11:
0000000000000246 R12:
0000000000000000
[ 35.833997] R13:
00007ffc9f2884c0 R14:
0000000000000001 R15:
0000000000674640
[ 35.834923] Code: 24 30 bb 01 00 00 00 45 31 f6 eb 5e 8b 50 08 83 c2 07 83 e2
fc 83 c2 70 49 8b 07 48 8b 40 70 48 85 c0 74 10 48 89 14 24 4c 89 ff <ff> d0 48
8b 14 24 48 01 c2 49 01 d6 45 85 ed 74 05 41 83 47 2c
[ 35.837442] RIP: tcf_action_init+0x90/0x190 RSP:
ffffb8edc068b9a0
[ 35.838291] ---[ end trace
a095c06ee4b97a26 ]---
Fixes:
d0f6dd8a914f ("net/sched: Introduce act_tunnel_key")
Signed-off-by: Roman Mashak <mrv@mojatatu.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Brad Mouring [Thu, 8 Mar 2018 22:23:03 +0000 (16:23 -0600)]
net: phy: Tell caller result of phy_change()
[ Upstream commit
a2c054a896b8ac794ddcfc7c92e2dc7ec4ed4ed5 ]
In
664fcf123a30e (net: phy: Threaded interrupts allow some simplification)
the phy_interrupt system was changed to use a traditional threaded
interrupt scheme instead of a workqueue approach.
With this change, the phy status check moved into phy_change, which
did not report back to the caller whether or not the interrupt was
handled. This means that, in the case of a shared phy interrupt,
only the first phydev's interrupt registers are checked (since
phy_interrupt() would always return IRQ_HANDLED). This leads to
interrupt storms when it is a secondary device that's actually the
interrupt source.
Signed-off-by: Brad Mouring <brad.mouring@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ido Schimmel [Thu, 15 Mar 2018 12:49:56 +0000 (14:49 +0200)]
mlxsw: spectrum_buffers: Set a minimum quota for CPU port traffic
[ Upstream commit
bcdd5de80a2275f7879dc278bfc747f1caf94442 ]
In commit
9ffcc3725f09 ("mlxsw: spectrum: Allow packets to be trapped
from any PG") I fixed a problem where packets could not be trapped to
the CPU due to exceeded shared buffer quotas. The mentioned commit
explains the problem in detail.
The problem was fixed by assigning a minimum quota for the CPU port and
the traffic class used for scheduling traffic to the CPU.
However, commit
117b0dad2d54 ("mlxsw: Create a different trap group list
for each device") assigned different traffic classes to different
packet types and rendered the fix useless.
Fix the problem by assigning a minimum quota for the CPU port and all
the traffic classes that are currently in use.
Fixes:
117b0dad2d54 ("mlxsw: Create a different trap group list for each device")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Eddie Shklaer <eddies@mellanox.com>
Tested-by: Eddie Shklaer <eddies@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
David Lebrun [Tue, 20 Mar 2018 14:44:55 +0000 (14:44 +0000)]
ipv6: sr: fix scheduling in RCU when creating seg6 lwtunnel state
[ Upstream commit
191f86ca8ef27f7a492fd1c03620498c6e94f0ac ]
The seg6_build_state() function is called with RCU read lock held,
so we cannot use GFP_KERNEL. This patch uses GFP_ATOMIC instead.
[ 92.770271] =============================
[ 92.770628] WARNING: suspicious RCU usage
[ 92.770921] 4.16.0-rc4+ #12 Not tainted
[ 92.771277] -----------------------------
[ 92.771585] ./include/linux/rcupdate.h:302 Illegal context switch in RCU read-side critical section!
[ 92.772279]
[ 92.772279] other info that might help us debug this:
[ 92.772279]
[ 92.773067]
[ 92.773067] rcu_scheduler_active = 2, debug_locks = 1
[ 92.773514] 2 locks held by ip/2413:
[ 92.773765] #0: (rtnl_mutex){+.+.}, at: [<
00000000e5461720>] rtnetlink_rcv_msg+0x441/0x4d0
[ 92.774377] #1: (rcu_read_lock){....}, at: [<
00000000df4f161e>] lwtunnel_build_state+0x59/0x210
[ 92.775065]
[ 92.775065] stack backtrace:
[ 92.775371] CPU: 0 PID: 2413 Comm: ip Not tainted 4.16.0-rc4+ #12
[ 92.775791] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1.fc27 04/01/2014
[ 92.776608] Call Trace:
[ 92.776852] dump_stack+0x7d/0xbc
[ 92.777130] __schedule+0x133/0xf00
[ 92.777393] ? unwind_get_return_address_ptr+0x50/0x50
[ 92.777783] ? __sched_text_start+0x8/0x8
[ 92.778073] ? rcu_is_watching+0x19/0x30
[ 92.778383] ? kernel_text_address+0x49/0x60
[ 92.778800] ? __kernel_text_address+0x9/0x30
[ 92.779241] ? unwind_get_return_address+0x29/0x40
[ 92.779727] ? pcpu_alloc+0x102/0x8f0
[ 92.780101] _cond_resched+0x23/0x50
[ 92.780459] __mutex_lock+0xbd/0xad0
[ 92.780818] ? pcpu_alloc+0x102/0x8f0
[ 92.781194] ? seg6_build_state+0x11d/0x240
[ 92.781611] ? save_stack+0x9b/0xb0
[ 92.781965] ? __ww_mutex_wakeup_for_backoff+0xf0/0xf0
[ 92.782480] ? seg6_build_state+0x11d/0x240
[ 92.782925] ? lwtunnel_build_state+0x1bd/0x210
[ 92.783393] ? ip6_route_info_create+0x687/0x1640
[ 92.783846] ? ip6_route_add+0x74/0x110
[ 92.784236] ? inet6_rtm_newroute+0x8a/0xd0
Fixes:
6c8702c60b886 ("ipv6: sr: add support for SRH encapsulation and injection with lwtunnels")
Signed-off-by: David Lebrun <dlebrun@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
David Lebrun [Tue, 20 Mar 2018 14:44:56 +0000 (14:44 +0000)]
ipv6: sr: fix NULL pointer dereference when setting encap source address
[ Upstream commit
8936ef7604c11b5d701580d779e0f5684abc7b68 ]
When using seg6 in encap mode, we call ipv6_dev_get_saddr() to set the
source address of the outer IPv6 header, in case none was specified.
Using skb->dev can lead to BUG() when it is in an inconsistent state.
This patch uses the net_device attached to the skb's dst instead.
[940807.667429] BUG: unable to handle kernel NULL pointer dereference at
000000000000047c
[940807.762427] IP: ipv6_dev_get_saddr+0x8b/0x1d0
[940807.815725] PGD 0 P4D 0
[940807.847173] Oops: 0000 [#1] SMP PTI
[940807.890073] Modules linked in:
[940807.927765] CPU: 6 PID: 0 Comm: swapper/6 Tainted: G W 4.16.0-rc1-seg6bpf+ #2
[940808.028988] Hardware name: HP ProLiant DL120 G6/ProLiant DL120 G6, BIOS O26 09/06/2010
[940808.128128] RIP: 0010:ipv6_dev_get_saddr+0x8b/0x1d0
[940808.187667] RSP: 0018:
ffff88043fd836b0 EFLAGS:
00010206
[940808.251366] RAX:
0000000000000005 RBX:
ffff88042cb1c860 RCX:
00000000000000fe
[940808.338025] RDX:
00000000000002c0 RSI:
ffff88042cb1c860 RDI:
0000000000004500
[940808.424683] RBP:
ffff88043fd83740 R08:
0000000000000000 R09:
ffffffffffffffff
[940808.511342] R10:
0000000000000040 R11:
0000000000000000 R12:
ffff88042cb1c850
[940808.598012] R13:
ffffffff8208e380 R14:
ffff88042ac8da00 R15:
0000000000000002
[940808.684675] FS:
0000000000000000(0000) GS:
ffff88043fd80000(0000) knlGS:
0000000000000000
[940808.783036] CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
[940808.852975] CR2:
000000000000047c CR3:
00000004255fe000 CR4:
00000000000006e0
[940808.939634] Call Trace:
[940808.970041] <IRQ>
[940808.995250] ? ip6t_do_table+0x265/0x640
[940809.043341] seg6_do_srh_encap+0x28f/0x300
[940809.093516] ? seg6_do_srh+0x1a0/0x210
[940809.139528] seg6_do_srh+0x1a0/0x210
[940809.183462] seg6_output+0x28/0x1e0
[940809.226358] lwtunnel_output+0x3f/0x70
[940809.272370] ip6_xmit+0x2b8/0x530
[940809.313185] ? ac6_proc_exit+0x20/0x20
[940809.359197] inet6_csk_xmit+0x7d/0xc0
[940809.404173] tcp_transmit_skb+0x548/0x9a0
[940809.453304] __tcp_retransmit_skb+0x1a8/0x7a0
[940809.506603] ? ip6_default_advmss+0x40/0x40
[940809.557824] ? tcp_current_mss+0x24/0x90
[940809.605925] tcp_retransmit_skb+0xd/0x80
[940809.654016] tcp_xmit_retransmit_queue.part.17+0xf9/0x210
[940809.719797] tcp_ack+0xa47/0x1110
[940809.760612] tcp_rcv_established+0x13c/0x570
[940809.812865] tcp_v6_do_rcv+0x151/0x3d0
[940809.858879] tcp_v6_rcv+0xa5c/0xb10
[940809.901770] ? seg6_output+0xdd/0x1e0
[940809.946745] ip6_input_finish+0xbb/0x460
[940809.994837] ip6_input+0x74/0x80
[940810.034612] ? ip6_rcv_finish+0xb0/0xb0
[940810.081663] ipv6_rcv+0x31c/0x4c0
...
Fixes:
6c8702c60b886 ("ipv6: sr: add support for SRH encapsulation and injection with lwtunnels")
Reported-by: Tom Herbert <tom@quantonium.net>
Signed-off-by: David Lebrun <dlebrun@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stefano Brivio [Mon, 19 Mar 2018 10:24:58 +0000 (11:24 +0100)]
ipv6: old_dport should be a __be16 in __ip6_datagram_connect()
[ Upstream commit
5f2fb802eee1df0810b47ea251942fe3fd36589a ]
Fixes:
2f987a76a977 ("net: ipv6: keep sk status consistent after datagram connect failure")
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Paolo Abeni [Mon, 12 Mar 2018 13:54:23 +0000 (14:54 +0100)]
net: ipv6: keep sk status consistent after datagram connect failure
[ Upstream commit
2f987a76a97773beafbc615b9c4d8fe79129a7f4 ]
On unsuccesful ip6_datagram_connect(), if the failure is caused by
ip6_datagram_dst_update(), the sk peer information are cleared, but
the sk->sk_state is preserved.
If the socket was already in an established status, the overall sk
status is inconsistent and fouls later checks in datagram code.
Fix this saving the old peer information and restoring them in
case of failure. This also aligns ipv6 datagram connect() behavior
with ipv4.
v1 -> v2:
- added missing Fixes tag
Fixes:
85cb73ff9b74 ("net: ipv6: reset daddr and dport in sk if connect() fails")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Shannon Nelson [Fri, 9 Mar 2018 00:17:23 +0000 (16:17 -0800)]
macvlan: filter out unsupported feature flags
[ Upstream commit
13fbcc8dc573482dd3f27568257fd7087f8935f4 ]
Adding a macvlan device on top of a lowerdev that supports
the xfrm offloads fails with a new regression:
# ip link add link ens1f0 mv0 type macvlan
RTNETLINK answers: Operation not permitted
Tracing down the failure shows that the macvlan device inherits
the NETIF_F_HW_ESP and NETIF_F_HW_ESP_TX_CSUM feature flags
from the lowerdev, but with no dev->xfrmdev_ops API filled
in, it doesn't actually support xfrm. When the request is
made to add the new macvlan device, the XFRM listener for
NETDEV_REGISTER calls xfrm_api_check() which fails the new
registration because dev->xfrmdev_ops is NULL.
The macvlan creation succeeds when we filter out the ESP
feature flags in macvlan_fix_features(), so let's filter them
out like we're already filtering out ~NETIF_F_NETNS_LOCAL.
When XFRM support is added in the future, we can add the flags
into MACVLAN_FEATURES.
This same problem could crop up in the future with any other
new feature flags, so let's filter out any flags that aren't
defined as supported in macvlan.
Fixes:
d77e38e612a0 ("xfrm: Add an IPsec hardware offloading API")
Reported-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Arkadi Sharshevsky [Sun, 18 Mar 2018 15:37:22 +0000 (17:37 +0200)]
devlink: Remove redundant free on error path
[ Upstream commit
7fe4d6dcbcb43fe0282d4213fc52be178bb30e91 ]
The current code performs unneeded free. Remove the redundant skb freeing
during the error path.
Fixes:
1555d204e743 ("devlink: Support for pipeline debug (dpipe)")
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Grygorii Strashko [Fri, 16 Mar 2018 22:08:35 +0000 (17:08 -0500)]
net: phy: relax error checking when creating sysfs link netdev->phydev
[ Upstream commit
4414b3ed74be0e205e04e12cd83542a727d88255 ]
Some ethernet drivers (like TI CPSW) may connect and manage >1 Net PHYs per
one netdevice, as result such drivers will produce warning during system
boot and fail to connect second phy to netdevice when PHYLIB framework
will try to create sysfs link netdev->phydev for second PHY
in phy_attach_direct(), because sysfs link with the same name has been
created already for the first PHY. As result, second CPSW external
port will became unusable.
Fix it by relaxing error checking when PHYLIB framework is creating sysfs
link netdev->phydev in phy_attach_direct(), suppressing warning by using
sysfs_create_link_nowarn() and adding error message instead.
After this change links (phy->netdev and netdev->phy) creation failure is not
fatal any more and system can continue working, which fixes TI CPSW issue.
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Fixes:
a3995460491d ("net: phy: Relax error checking on sysfs_create_link()")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Grygorii Strashko [Fri, 16 Mar 2018 22:08:34 +0000 (17:08 -0500)]
sysfs: symlink: export sysfs_create_link_nowarn()
[ Upstream commit
2399ac42e762ab25c58420e25359b2921afdc55f ]
The sysfs_create_link_nowarn() is going to be used in phylib framework in
subsequent patch which can be built as module. Hence, export
sysfs_create_link_nowarn() to avoid build errors.
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Fixes:
a3995460491d ("net: phy: Relax error checking on sysfs_create_link()")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Michal Kalderon [Wed, 14 Mar 2018 12:49:28 +0000 (14:49 +0200)]
qed: Fix non TCP packets should be dropped on iWARP ll2 connection
[ Upstream commit
16da09047d3fb991dc48af41f6d255fd578e8ca2 ]
FW workaround. The iWARP LL2 connection did not expect TCP packets
to arrive on it's connection. The fix drops any non-tcp packets
Fixes b5c29ca ("qed: iWARP CM - setup a ll2 connection for handling
SYN packets")
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Soheil Hassas Yeganeh [Tue, 6 Mar 2018 22:15:12 +0000 (17:15 -0500)]
tcp: purge write queue upon aborting the connection
[ Upstream commit
e05836ac07c77dd90377f8c8140bce2a44af5fe7 ]
When the connection is aborted, there is no point in
keeping the packets on the write queue until the connection
is closed.
Similar to
a27fd7a8ed38 ('tcp: purge write queue upon RST'),
this is essential for a correct MSG_ZEROCOPY implementation,
because userspace cannot call close(fd) before receiving
zerocopy signals even when the connection is aborted.
Fixes:
f214f915e7db ("tcp: enable MSG_ZEROCOPY")
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Soheil Hassas Yeganeh [Thu, 15 Mar 2018 16:09:13 +0000 (12:09 -0400)]
tcp: reset sk_send_head in tcp_write_queue_purge
tcp_write_queue_purge clears all the SKBs in the write queue
but does not reset the sk_send_head. As a result, we can have
a NULL pointer dereference anywhere that we use tcp_send_head
instead of the tcp_write_queue_tail.
For example, after
a27fd7a8ed38 (tcp: purge write queue upon RST),
we can purge the write queue on RST. Prior to
75c119afe14f (tcp: implement rb-tree based retransmit queue),
tcp_push will only check tcp_send_head and then accesses
tcp_write_queue_tail to send the actual SKB. As a result, it will
dereference a NULL pointer.
This has been reported twice for 4.14 where we don't have
75c119afe14f:
By Timofey Titovets:
[ 422.081094] BUG: unable to handle kernel NULL pointer dereference
at
0000000000000038
[ 422.081254] IP: tcp_push+0x42/0x110
[ 422.081314] PGD 0 P4D 0
[ 422.081364] Oops: 0002 [#1] SMP PTI
By Yongjian Xu:
BUG: unable to handle kernel NULL pointer dereference at
0000000000000038
IP: tcp_push+0x48/0x120
PGD
80000007ff77b067 P4D
80000007ff77b067 PUD
7fd989067 PMD 0
Oops: 0002 [#18] SMP PTI
Modules linked in: tcp_diag inet_diag tcp_bbr sch_fq iTCO_wdt
iTCO_vendor_support pcspkr ixgbe mdio i2c_i801 lpc_ich joydev input_leds shpchp
e1000e igb dca ptp pps_core hwmon mei_me mei ipmi_si ipmi_msghandler sg ses
scsi_transport_sas enclosure ext4 jbd2 mbcache sd_mod ahci libahci megaraid_sas
wmi ast ttm dm_mirror dm_region_hash dm_log dm_mod dax
CPU: 6 PID: 14156 Comm: [ET_NET 6] Tainted: G D 4.14.26-1.el6.x86_64 #1
Hardware name: LENOVO ThinkServer RD440 /ThinkServer RD440, BIOS A0TS80A
09/22/2014
task:
ffff8807d78d8140 task.stack:
ffffc9000e944000
RIP: 0010:tcp_push+0x48/0x120
RSP: 0018:
ffffc9000e947a88 EFLAGS:
00010246
RAX:
00000000000005b4 RBX:
ffff880f7cce9c00 RCX:
0000000000000000
RDX:
0000000000000000 RSI:
0000000000000040 RDI:
ffff8807d00f5000
RBP:
ffffc9000e947aa8 R08:
0000000000001c84 R09:
0000000000000000
R10:
ffff8807d00f5158 R11:
0000000000000000 R12:
ffff8807d00f5000
R13:
0000000000000020 R14:
00000000000256d4 R15:
0000000000000000
FS:
00007f5916de9700(0000) GS:
ffff88107fd00000(0000) knlGS:
0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
CR2:
0000000000000038 CR3:
00000007f8226004 CR4:
00000000001606e0
Call Trace:
tcp_sendmsg_locked+0x33d/0xe50
tcp_sendmsg+0x37/0x60
inet_sendmsg+0x39/0xc0
sock_sendmsg+0x49/0x60
sock_write_iter+0xb6/0x100
do_iter_readv_writev+0xec/0x130
? rw_verify_area+0x49/0xb0
do_iter_write+0x97/0xd0
vfs_writev+0x7e/0xe0
? __wake_up_common_lock+0x80/0xa0
? __fget_light+0x2c/0x70
? __do_page_fault+0x1e7/0x530
do_writev+0x60/0xf0
? inet_shutdown+0xac/0x110
SyS_writev+0x10/0x20
do_syscall_64+0x6f/0x140
? prepare_exit_to_usermode+0x8b/0xa0
entry_SYSCALL_64_after_hwframe+0x3d/0xa2
RIP: 0033:0x3135ce0c57
RSP: 002b:
00007f5916de4b00 EFLAGS:
00000293 ORIG_RAX:
0000000000000014
RAX:
ffffffffffffffda RBX:
0000000000000000 RCX:
0000003135ce0c57
RDX:
0000000000000002 RSI:
00007f5916de4b90 RDI:
000000000000606f
RBP:
0000000000000000 R08:
0000000000000000 R09:
00007f5916de8c38
R10:
0000000000000000 R11:
0000000000000293 R12:
00000000000464cc
R13:
00007f5916de8c30 R14:
00007f58d8bef080 R15:
0000000000000002
Code: 48 8b 97 60 01 00 00 4c 8d 97 58 01 00 00 41 b9 00 00 00 00 41 89 f3 4c 39
d2 49 0f 44 d1 41 81 e3 00 80 00 00 0f 85 b0 00 00 00 <80> 4a 38 08 44 8b 8f 74
06 00 00 44 89 8f 7c 06 00 00 83 e6 01
RIP: tcp_push+0x48/0x120 RSP:
ffffc9000e947a88
CR2:
0000000000000038
---[ end trace
8d545c2e93515549 ]---
Fixes:
a27fd7a8ed38 (tcp: purge write queue upon RST)
Reported-by: Timofey Titovets <nefelim4ag@gmail.com>
Reported-by: Yongjian Xu <yongjianchn@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Tested-by: Yongjian Xu <yongjianchn@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Greg Kroah-Hartman [Wed, 28 Mar 2018 16:24:51 +0000 (18:24 +0200)]
Linux 4.14.31
Daniel Borkmann [Wed, 7 Mar 2018 21:10:01 +0000 (22:10 +0100)]
bpf, x64: increase number of passes
commit
6007b080d2e2adb7af22bf29165f0594ea12b34c upstream.
In Cilium some of the main programs we run today are hitting 9 passes
on x64's JIT compiler, and we've had cases already where we surpassed
the limit where the JIT then punts the program to the interpreter
instead, leading to insertion failures due to CONFIG_BPF_JIT_ALWAYS_ON
or insertion failures due to the prog array owner being JITed but the
program to insert not (both must have the same JITed/non-JITed property).
One concrete case the program image shrunk from 12,767 bytes down to
10,288 bytes where the image converged after 16 steps. I've measured
that this took 340us in the JIT until it converges on my i7-6600U. Thus,
increase the original limit we had from day one where the JIT covered
cBPF only back then before we run into the case (as similar with the
complexity limit) where we trip over this and hit program rejections.
Also add a cond_resched() into the compilation loop, the JIT process
runs without any locks and may sleep anyway.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Chenbo Feng [Tue, 20 Mar 2018 00:57:27 +0000 (17:57 -0700)]
bpf: skip unnecessary capability check
commit
0fa4fe85f4724fff89b09741c437cbee9cf8b008 upstream.
The current check statement in BPF syscall will do a capability check
for CAP_SYS_ADMIN before checking sysctl_unprivileged_bpf_disabled. This
code path will trigger unnecessary security hooks on capability checking
and cause false alarms on unprivileged process trying to get CAP_SYS_ADMIN
access. This can be resolved by simply switch the order of the statement
and CAP_SYS_ADMIN is not required anyway if unprivileged bpf syscall is
allowed.
Signed-off-by: Chenbo Feng <fengc@google.com>
Acked-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Daniel Borkmann [Wed, 21 Mar 2018 00:18:24 +0000 (01:18 +0100)]
kbuild: disable clang's default use of -fmerge-all-constants
commit
87e0d4f0f37fb0c8c4aeeac46fff5e957738df79 upstream.
Prasad reported that he has seen crashes in BPF subsystem with netd
on Android with arm64 in the form of (note, the taint is unrelated):
[ 4134.721483] Unable to handle kernel paging request at virtual address
800000001
[ 4134.820925] Mem abort info:
[ 4134.901283] Exception class = DABT (current EL), IL = 32 bits
[ 4135.016736] SET = 0, FnV = 0
[ 4135.119820] EA = 0, S1PTW = 0
[ 4135.201431] Data abort info:
[ 4135.301388] ISV = 0, ISS = 0x00000021
[ 4135.359599] CM = 0, WnR = 0
[ 4135.470873] user pgtable: 4k pages, 39-bit VAs, pgd =
ffffffe39b946000
[ 4135.499757] [
0000000800000001] *pgd=
0000000000000000, *pud=
0000000000000000
[ 4135.660725] Internal error: Oops:
96000021 [#1] PREEMPT SMP
[ 4135.674610] Modules linked in:
[ 4135.682883] CPU: 5 PID: 1260 Comm: netd Tainted: G S W 4.14.19+ #1
[ 4135.716188] task:
ffffffe39f4aa380 task.stack:
ffffff801d4e0000
[ 4135.731599] PC is at bpf_prog_add+0x20/0x68
[ 4135.741746] LR is at bpf_prog_inc+0x20/0x2c
[ 4135.751788] pc : [<
ffffff94ab7ad584>] lr : [<
ffffff94ab7ad638>] pstate:
60400145
[ 4135.769062] sp :
ffffff801d4e3ce0
[...]
[ 4136.258315] Process netd (pid: 1260, stack limit = 0xffffff801d4e0000)
[ 4136.273746] Call trace:
[...]
[ 4136.442494] 3ca0:
ffffff94ab7ad584 0000000060400145 ffffffe3a01bf8f8 0000000000000006
[ 4136.460936] 3cc0:
0000008000000000 ffffff94ab844204 ffffff801d4e3cf0 ffffff94ab7ad584
[ 4136.479241] [<
ffffff94ab7ad584>] bpf_prog_add+0x20/0x68
[ 4136.491767] [<
ffffff94ab7ad638>] bpf_prog_inc+0x20/0x2c
[ 4136.504536] [<
ffffff94ab7b5d08>] bpf_obj_get_user+0x204/0x22c
[ 4136.518746] [<
ffffff94ab7ade68>] SyS_bpf+0x5a8/0x1a88
Android's netd was basically pinning the uid cookie BPF map in BPF
fs (/sys/fs/bpf/traffic_cookie_uid_map) and later on retrieving it
again resulting in above panic. Issue is that the map was wrongly
identified as a prog! Above kernel was compiled with clang 4.0,
and it turns out that clang decided to merge the bpf_prog_iops and
bpf_map_iops into a single memory location, such that the two i_ops
could then not be distinguished anymore.
Reason for this miscompilation is that clang has the more aggressive
-fmerge-all-constants enabled by default. In fact, clang source code
has a comment about it in lib/AST/ExprConstant.cpp on why it is okay
to do so:
Pointers with different bases cannot represent the same object.
(Note that clang defaults to -fmerge-all-constants, which can
lead to inconsistent results for comparisons involving the address
of a constant; this generally doesn't matter in practice.)
The issue never appeared with gcc however, since gcc does not enable
-fmerge-all-constants by default and even *explicitly* states in
it's option description that using this flag results in non-conforming
behavior, quote from man gcc:
Languages like C or C++ require each variable, including multiple
instances of the same variable in recursive calls, to have distinct
locations, so using this option results in non-conforming behavior.
There are also various clang bug reports open on that matter [1],
where clang developers acknowledge the non-conforming behavior,
and refer to disabling it with -fno-merge-all-constants. But even
if this gets fixed in clang today, there are already users out there
that triggered this. Thus, fix this issue by explicitly adding
-fno-merge-all-constants to the kernel's Makefile to generically
disable this optimization, since potentially other places in the
kernel could subtly break as well.
Note, there is also a flag called -fmerge-constants (not supported
by clang), which is more conservative and only applies to strings
and it's enabled in gcc's -O/-O2/-O3/-Os optimization levels. In
gcc's code, the two flags -fmerge-{all-,}constants share the same
variable internally, so when disabling it via -fno-merge-all-constants,
then we really don't merge any const data (e.g. strings), and text
size increases with gcc (14,927,214 -> 14,942,646 for vmlinux.o).
$ gcc -fverbose-asm -O2 foo.c -S -o foo.S
-> foo.S lists -fmerge-constants under options enabled
$ gcc -fverbose-asm -O2 -fno-merge-all-constants foo.c -S -o foo.S
-> foo.S doesn't list -fmerge-constants under options enabled
$ gcc -fverbose-asm -O2 -fno-merge-all-constants -fmerge-constants foo.c -S -o foo.S
-> foo.S lists -fmerge-constants under options enabled
Thus, as a workaround we need to set both -fno-merge-all-constants
*and* -fmerge-constants in the Makefile in order for text size to
stay as is.
[1] https://bugs.llvm.org/show_bug.cgi?id=18538
Reported-by: Prasad Sodagudi <psodagud@codeaurora.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Chenbo Feng <fengc@google.com>
Cc: Richard Smith <richard-llvm@metafoo.co.uk>
Cc: Chandler Carruth <chandlerc@gmail.com>
Cc: linux-kernel@vger.kernel.org
Tested-by: Prasad Sodagudi <psodagud@codeaurora.org>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dave Hansen [Sat, 11 Nov 2017 00:12:31 +0000 (16:12 -0800)]
x86/pkeys/selftests: Rename 'si_pkey' to 'siginfo_pkey'
commit
91c49c2deb96ffc3c461eaae70219d89224076b7 upstream.
'si_pkey' is now #defined to be the name of the new siginfo field that
protection keys uses. Rename it not to conflict.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20171111001231.DFFC8285@viggo.jf.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Lu Baolu [Thu, 5 Oct 2017 08:21:41 +0000 (11:21 +0300)]
usb: xhci: Fix potential memory leak in xhci_disable_slot()
commit
cd3f1790b006d91786728c20a01da21ee277aff1 upstream.
xhci_disable_slot() allows the invoker to pass a command pointer
as paramenter. Otherwise, it will allocate one. This will cause
memory leak when a command structure was allocated inside of this
function while queuing command trb fails. Another problem comes up
when the invoker passed a command pointer, but xhci_disable_slot()
frees it when it detects a dead host.
This patch fixes these two problems by removing the command parameter
from xhci_disable_slot().
Fixes:
f9e609b82479 ("usb: xhci: Add helper function xhci_disable_slot().")
Cc: Guoqing Zhang <guoqing.zhang@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Lu Baolu [Thu, 5 Oct 2017 08:21:40 +0000 (11:21 +0300)]
usb: xhci: Disable slot even when virt-dev is null
commit
b64149ca016c25f30b39ac5a8f37cfb9017e19bb upstream.
xhci_disable_slot() is a helper for disabling a slot when a device
goes away or recovers from error situations. Currently, it checks
the corespoding virt-dev pointer and returns directly (w/o issuing
disable slot command) if it's null.
This is unnecessary and will cause problems in case where virt-dev
allocation fails and xhci_disable_slot() is called to roll back the
hardware state. Refer to the implementation of xhci_alloc_dev().
This patch removes lines to check virt-dev in xhci_disable_slot().
Fixes:
f9e609b82479 ("usb: xhci: Add helper function xhci_disable_slot().")
Cc: Guoqing Zhang <guoqing.zhang@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Nadav Amit [Tue, 5 Sep 2017 20:25:25 +0000 (20:25 +0000)]
staging: lustre: ptlrpc: kfree used instead of kvfree
commit
c3eec59659cf25916647d2178c541302bb4822ad upstream.
rq_reqbuf is allocated using kvmalloc() but released in one occasion
using kfree() instead of kvfree().
The issue was found using grep based on a similar bug.
Fixes:
d7e09d0397e8 ("add Lustre file system client support")
Fixes:
ee0ec1946ec2 ("lustre: ptlrpc: Replace uses of OBD_{ALLOC,FREE}_LARGE")
Cc: Peng Tao <bergwolf@gmail.com>
Cc: Oleg Drokin <oleg.drokin@intel.com>
Cc: James Simmons <jsimmons@infradead.org>
Signed-off-by: Nadav Amit <namit@vmware.com>
Signed-off-by: Andreas Dilger <andreas.dilger@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Liam Mark [Fri, 26 Jan 2018 17:48:18 +0000 (09:48 -0800)]
staging: android: ion: Zero CMA allocated memory
commit
6d79bd5bb6c79a9dba4842040c9adf39e7806330 upstream.
Since commit
204f672255c2 ("staging: android: ion: Use CMA APIs directly")
the CMA API is now used directly and therefore the allocated memory is no
longer automatically zeroed.
Explicitly zero CMA allocated memory to ensure that no data is exposed to
userspace.
Fixes:
204f672255c2 ("staging: android: ion: Use CMA APIs directly")
Signed-off-by: Liam Mark <lmark@codeaurora.org>
Acked-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Lorenzo Bianconi [Mon, 1 Jan 2018 18:54:42 +0000 (19:54 +0100)]
iio: imu: st_lsm6dsx: fix endianness in st_lsm6dsx_read_oneshot()
commit
7b9ebe428266fb7e0a6d769bb3ff3fcb6044b15e upstream.
Apply le16_to_cpu() to data read from the sensor in order to take into
account architecture endianness
Fixes:
290a6ce11d93 (iio: imu: add support to lsm6dsx driver)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Walleij [Tue, 5 Dec 2017 10:57:27 +0000 (11:57 +0100)]
iio: ABI: Fix name of timestamp sysfs file
commit
b9a3589332c2a25fb7edad25a26fcaada3209126 upstream.
The name of the file is "current_timetamp_clock" not
"timestamp_clock".
Fixes:
bc2b7dab629a ("iio:core: timestamping clock selection support")
Cc: Gregor Boirie <gregor.boirie@parrot.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kan Liang [Tue, 13 Mar 2018 18:51:34 +0000 (11:51 -0700)]
perf/x86/intel/uncore: Fix multi-domain PCI CHA enumeration bug on Skylake servers
commit
320b0651f32b830add6497fcdcfdcb6ae8c7b8a0 upstream.
The number of CHAs is miscalculated on multi-domain PCI Skylake server systems,
resulting in an uncore driver initialization error.
Gary Kroening explains:
"For systems with a single PCI segment, it is sufficient to look for the
bus number to change in order to determine that all of the CHa's have
been counted for a single socket.
However, for multi PCI segment systems, each socket is given a new
segment and the bus number does NOT change. So looking only for the
bus number to change ends up counting all of the CHa's on all sockets
in the system. This leads to writing CPU MSRs beyond a valid range and
causes an error in ivbep_uncore_msr_init_box()."
To fix this bug, query the number of CHAs from the CAPID6 register:
it should read bits 27:0 in the CAPID6 register located at
Device 30, Function 3, Offset 0x9C. These 28 bits form a bit vector
of available LLC slices and the CHAs that manage those slices.
Reported-by: Kroening, Gary <gary.kroening@hpe.com>
Tested-by: Kroening, Gary <gary.kroening@hpe.com>
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: abanman@hpe.com
Cc: dimitri.sivanich@hpe.com
Cc: hpa@zytor.com
Cc: mike.travis@hpe.com
Cc: russ.anderson@hpe.com
Fixes:
cd34cd97b7b4 ("perf/x86/intel/uncore: Add Skylake server uncore support")
Link: http://lkml.kernel.org/r/1520967094-13219-1-git-send-email-kan.liang@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dan Carpenter [Sat, 17 Mar 2018 11:52:16 +0000 (14:52 +0300)]
perf/x86/intel: Don't accidentally clear high bits in bdw_limit_period()
commit
e5ea9b54a055619160bbfe527ebb7d7191823d66 upstream.
We intended to clear the lowest 6 bits but because of a type bug we
clear the high 32 bits as well. Andi says that periods are rarely more
than U32_MAX so this bug probably doesn't have a huge runtime impact.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Fixes:
294fe0f52a44 ("perf/x86/intel: Add INST_RETIRED.ALL workarounds")
Link: http://lkml.kernel.org/r/20180317115216.GB4035@mwanda
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Song Liu [Tue, 6 Mar 2018 05:55:04 +0000 (21:55 -0800)]
perf/core: Fix ctx_event_type in ctx_resched()
commit
bd903afeb504db5655a45bb4cf86f38be5b1bf62 upstream.
In ctx_resched(), EVENT_FLEXIBLE should be sched_out when EVENT_PINNED is
added. However, ctx_resched() calculates ctx_event_type before checking
this condition. As a result, pinned events will NOT get higher priority
than flexible events.
The following shows this issue on an Intel CPU (where ref-cycles can
only use one hardware counter).
1. First start:
perf stat -C 0 -e ref-cycles -I 1000
2. Then, in the second console, run:
perf stat -C 0 -e ref-cycles:D -I 1000
The second perf uses pinned events, which is expected to have higher
priority. However, because it failed in ctx_resched(). It is never
run.
This patch fixes this by calculating ctx_event_type after re-evaluating
event_type.
Reported-by: Ephraim Park <ephiepark@fb.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: <jolsa@redhat.com>
Cc: <kernel-team@fb.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Fixes:
487f05e18aa4 ("perf/core: Optimize event rescheduling on active contexts")
Link: http://lkml.kernel.org/r/20180306055504.3283731-1-songliubraving@fb.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ilya Pronin [Tue, 6 Mar 2018 06:43:53 +0000 (22:43 -0800)]
perf stat: Fix CVS output format for non-supported counters
commit
40c21898ba5372c14ef71717040529794a91ccc2 upstream.
When printing stats in CSV mode, 'perf stat' appends extra separators
when a counter is not supported:
<not supported>,,L1-dcache-store-misses,mesos/
bd442f34-2b4a-47df-b966-
9b281f9f56fc,0,100.00,,,,
Which causes a failure when parsing fields. The numbers of separators
should be the same for each line, no matter if the counter is or not
supported.
Signed-off-by: Ilya Pronin <ipronin@twitter.com>
Acked-by: Jiri Olsa <jolsa@redhat.com>
Cc: Andi Kleen <ak@linux.intel.com>
Link: http://lkml.kernel.org/r/20180306064353.31930-1-xiyou.wangcong@gmail.com
Fixes:
92a61f6412d3 ("perf stat: Implement CSV metrics output")
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kan Liang [Fri, 2 Mar 2018 15:22:30 +0000 (07:22 -0800)]
perf/x86/intel/uncore: Fix Skylake UPI event format
commit
317660940fd9dddd3201c2f92e25c27902c753fa upstream.
There is no event extension (bit 21) for SKX UPI, so
use 'event' instead of 'event_ext'.
Reported-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Fixes:
cd34cd97b7b4 ("perf/x86/intel/uncore: Add Skylake server uncore support")
Link: http://lkml.kernel.org/r/1520004150-4855-1-git-send-email-kan.liang@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Chris Wilson [Tue, 19 Dec 2017 12:07:00 +0000 (12:07 +0000)]
drm/syncobj: Stop reusing the same struct file for all syncobj -> fd
commit
e7cdf5c82f1773c3386b93bbcf13b9bfff29fa31 upstream.
The vk cts test:
dEQP-VK.api.external.semaphore.opaque_fd.export_multiple_times_temporary
triggers a lot of
VFS: Close: file count is 0
Dave pointed out that clearing the syncobj->file from
drm_syncobj_file_release() was sufficient to silence the test, but that
opens a can of worm since we assumed that the syncobj->file was never
unset. Stop trying to reuse the same struct file for every fd pointing
to the drm_syncobj, and allocate one file for each fd instead.
v2: Fixup return handling of drm_syncobj_fd_to_handle
v2.1: [airlied: fix possible syncobj ref race]
v2.2: [jekstrand: back-port to 4.14]
Reported-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Dave Airlie <airlied@redhat.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Jason Ekstrand <jason@jlekstrand.net>
Tested-by: Clayton Craft <clayton.a.craft@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
H.J. Lu [Mon, 19 Mar 2018 21:08:11 +0000 (14:08 -0700)]
x86/boot/64: Verify alignment of the LOAD segment
commit
c55b8550fa57ba4f5e507be406ff9fc2845713e8 upstream.
Since the x86-64 kernel must be aligned to 2MB, refuse to boot the
kernel if the alignment of the LOAD segment isn't a multiple of 2MB.
Signed-off-by: H.J. Lu <hjl.tools@gmail.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/CAMe9rOrR7xSJgUfiCoZLuqWUwymRxXPoGBW38%2BpN%3D9g%2ByKNhZw@mail.gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
H.J. Lu [Mon, 19 Mar 2018 20:57:46 +0000 (13:57 -0700)]
x86/build/64: Force the linker to use 2MB page size
commit
e3d03598e8ae7d195af5d3d049596dec336f569f upstream.
Binutils 2.31 will enable -z separate-code by default for x86 to avoid
mixing code pages with data to improve cache performance as well as
security. To reduce x86-64 executable and shared object sizes, the
maximum page size is reduced from 2MB to 4KB. But x86-64 kernel must
be aligned to 2MB. Pass -z max-page-size=0x200000 to linker to force
2MB page size regardless of the default page size used by linker.
Tested with Linux kernel 4.15.6 on x86-64.
Signed-off-by: H.J. Lu <hjl.tools@gmail.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/CAMe9rOp4_%3D_8twdpTyAP2DhONOCeaTOsniJLoppzhoNptL8xzA@mail.gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Torvalds [Tue, 20 Mar 2018 19:16:59 +0000 (12:16 -0700)]
kvm/x86: fix icebp instruction handling
commit
32d43cd391bacb5f0814c2624399a5dad3501d09 upstream.
The undocumented 'icebp' instruction (aka 'int1') works pretty much like
'int3' in the absense of in-circuit probing equipment (except,
obviously, that it raises #DB instead of raising #BP), and is used by
some validation test-suites as such.
But Andy Lutomirski noticed that his test suite acted differently in kvm
than on bare hardware.
The reason is that kvm used an inexact test for the icebp instruction:
it just assumed that an all-zero VM exit qualification value meant that
the VM exit was due to icebp.
That is not unlike the guess that do_debug() does for the actual
exception handling case, but it's purely a heuristic, not an absolute
rule. do_debug() does it because it wants to ascribe _some_ reasons to
the #DB that happened, and an empty %dr6 value means that 'icebp' is the
most likely casue and we have no better information.
But kvm can just do it right, because unlike the do_debug() case, kvm
actually sees the real reason for the #DB in the VM-exit interruption
information field.
So instead of relying on an inexact heuristic, just use the actual VM
exit information that says "it was 'icebp'".
Right now the 'icebp' instruction isn't technically documented by Intel,
but that will hopefully change. The special "privileged software
exception" information _is_ actually mentioned in the Intel SDM, even
though the cause of it isn't enumerated.
Reported-by: Andy Lutomirski <luto@kernel.org>
Tested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thomas Gleixner [Thu, 15 Feb 2018 16:21:55 +0000 (17:21 +0100)]
posix-timers: Protect posix clock array access against speculation
commit
19b558db12f9f4e45a22012bae7b4783e62224da upstream.
The clockid argument of clockid_to_kclock() comes straight from user space
via various syscalls and is used as index into the posix_clocks array.
Protect it against spectre v1 array out of bounds speculation. Remove the
redundant check for !posix_clock[id] as this is another source for
speculation and does not provide any advantage over the return
posix_clock[id] path which returns NULL in that case anyway.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Cc: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: stable@vger.kernel.org
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: David Woodhouse <dwmw@amazon.co.uk>
Link: https://lkml.kernel.org/r/alpine.DEB.2.21.1802151718320.1296@nanos.tec.linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Waiman Long [Thu, 22 Mar 2018 19:18:53 +0000 (15:18 -0400)]
x86/efi: Free efi_pgd with free_pages()
commit
06ace26f4e6fcf747e890a39193be811777a048a upstream.
The efi_pgd is allocated as PGD_ALLOCATION_ORDER pages and therefore must
also be freed as PGD_ALLOCATION_ORDER pages with free_pages().
Fixes:
d9e9a6418065 ("x86/mm/pti: Allocate a separate user PGD")
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/1521746333-19593-1-git-send-email-longman@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Boris Ostrovsky [Mon, 19 Mar 2018 14:31:54 +0000 (10:31 -0400)]
x86/vsyscall/64: Use proper accessor to update P4D entry
commit
31ad7f8e7dc94d3b85ccf9b6141ce6dfd35a1781 upstream.
Writing to it directly does not work for Xen PV guests.
Fixes:
49275fef986a ("x86/vsyscall/64: Explicitly set _PAGE_USER in the pagetable hierarchy")
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Juergen Gross <jgross@suse.com>
Acked-by: Andy Lutomirski <luto@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20180319143154.3742-1-boris.ostrovsky@oracle.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andy Lutomirski [Sat, 17 Mar 2018 15:25:07 +0000 (08:25 -0700)]
selftests/x86/ptrace_syscall: Fix for yet more glibc interference
commit
4b0b37d4cc54b21a6ecad7271cbc850555869c62 upstream.
glibc keeps getting cleverer, and my version now turns raise() into
more than one syscall. Since the test relies on ptrace seeing an
exact set of syscalls, this breaks the test. Replace raise(SIGSTOP)
with syscall(SYS_tgkill, ...) to force glibc to get out of our way.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kselftest@vger.kernel.org
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/bc80338b453afa187bc5f895bd8e2c8d6e264da2.1521300271.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andy Lutomirski [Thu, 23 Jul 2015 22:37:48 +0000 (15:37 -0700)]
x86/entry/64: Don't use IST entry for #BP stack
commit
d8ba61ba58c88d5207c1ba2f7d9a2280e7d03be9 upstream.
There's nothing IST-worthy about #BP/int3. We don't allow kprobes
in the small handful of places in the kernel that run at CPL0 with
an invalid stack, and 32-bit kernels have used normal interrupt
gates for #BP forever.
Furthermore, we don't allow kprobes in places that have usergs while
in kernel mode, so "paranoid" is also unnecessary.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Torvalds [Sat, 24 Mar 2018 09:43:26 +0000 (10:43 +0100)]
tty: vt: fix up tabstops properly
commit
f1869a890cdedb92a3fab969db5d0fd982850273 upstream.
Tabs on a console with long lines do not wrap properly, so correctly
account for the line length when computing the tab placement location.
Reported-by: James Holderness <j4_james@hotmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andri Yngvason [Thu, 15 Mar 2018 18:23:17 +0000 (18:23 +0000)]
can: cc770: Fix use after free in cc770_tx_interrupt()
commit
9ffd7503944ec7c0ef41c3245d1306c221aef2be upstream.
This fixes use after free introduced by the last cc770 patch.
Signed-off-by: Andri Yngvason <andri.yngvason@marel.com>
Fixes:
746201235b3f ("can: cc770: Fix queue stall & dropped RTR reply")
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andri Yngvason [Wed, 14 Mar 2018 11:52:57 +0000 (11:52 +0000)]
can: cc770: Fix queue stall & dropped RTR reply
commit
746201235b3f876792099079f4c6fea941d76183 upstream.
While waiting for the TX object to send an RTR, an external message with a
matching id can overwrite the TX data. In this case we must call the rx
routine and then try transmitting the message that was overwritten again.
The queue was being stalled because the RX event did not generate an
interrupt to wake up the queue again and the TX event did not happen
because the TXRQST flag is reset by the chip when new data is received.
According to the CC770 datasheet the id of a message object should not be
changed while the MSGVAL bit is set. This has been fixed by resetting the
MSGVAL bit before modifying the object in the transmit function and setting
it after. It is not enough to set & reset CPUUPD.
It is important to keep the MSGVAL bit reset while the message object is
being modified. Otherwise, during RTR transmission, a frame with matching
id could trigger an rx-interrupt, which would cause a race condition
between the interrupt routine and the transmit function.
Signed-off-by: Andri Yngvason <andri.yngvason@marel.com>
Tested-by: Richard Weinberger <richard@nod.at>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andri Yngvason [Wed, 14 Mar 2018 11:52:56 +0000 (11:52 +0000)]
can: cc770: Fix stalls on rt-linux, remove redundant IRQ ack
commit
f4353daf4905c0099fd25fa742e2ffd4a4bab26a upstream.
This has been reported to cause stalls on rt-linux.
Suggested-by: Richard Weinberger <richard@nod.at>
Tested-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Andri Yngvason <andri.yngvason@marel.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Marek Vasut [Mon, 5 Mar 2018 20:29:52 +0000 (21:29 +0100)]
can: ifi: Check core revision upon probe
commit
591d65d5b15496af8d05e252bc1da611c66c0b79 upstream.
Older versions of the core are not compatible with the driver due
to various intrusive fixes of the core. Read out the VER register,
check the core revision bitfield and verify if the core in use is
new enough (rev 2.1 or newer) to work correctly with this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Markus Marb <markus@marb.org>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Marek Vasut [Thu, 1 Mar 2018 18:34:00 +0000 (19:34 +0100)]
can: ifi: Repair the error handling
commit
880dd464b4304583c557c4e5f5ecebfd55d232b1 upstream.
The new version of the IFI CANFD core has significantly less complex
error state indication logic. In particular, the warning/error state
bits are no longer all over the place, but are all present in the
STATUS register. Moreover, there is a new IRQ register bit indicating
transition between error states (active/warning/passive/busoff).
This patch makes use of this bit to weed out the obscure selective
INTERRUPT register clearing, which was used to carry over the error
state indication into the poll function. While at it, this patch
fixes the handling of the ACTIVE state, since the hardware provides
indication of the core being in ACTIVE state and that in turn fixes
the state transition indication toward userspace. Finally, register
reads in the poll function are moved to the matching subfunctions
since those are also no longer needed in the poll function.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Markus Marb <markus@marb.org>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stephane Grosjean [Thu, 8 Mar 2018 08:30:29 +0000 (09:30 +0100)]
can: peak/pcie_fd: remove useless code when interface starts
commit
ffd137f7043cb30067e1bff6fe62a073ae190b23 upstream.
When an interface starts, the echo_skb array is empty and the network
queue should be started only. This patch replaces useless code and locks
when the internal RX_BARRIER message is received from the IP core, telling
the driver that tx may start.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stephane Grosjean [Thu, 8 Mar 2018 08:30:28 +0000 (09:30 +0100)]
can: peak/pcie_fd: fix echo_skb is occupied! bug
commit
e6048a00cfd0863d32f53b226e0b9a3633fc3332 upstream.
This patch makes atomic the handling of the linux-can echo_skb array and
the network tx queue. This prevents from the "BUG! echo_skb is occupied!"
message to be printed by the linux-can core, in SMP environments.
Reported-by: Diana Burgess <diana@peloton-tech.com>
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dan Carpenter [Mon, 19 Mar 2018 11:07:45 +0000 (14:07 +0300)]
staging: ncpfs: memory corruption in ncp_read_kernel()
commit
4c41aa24baa4ed338241d05494f2c595c885af8f upstream.
If the server is malicious then *bytes_read could be larger than the
size of the "target" buffer. It would lead to memory corruption when we
do the memcpy().
Reported-by: Dr Silvio Cesare of InfoSect <Silvio Cesare <silvio.cesare@gmail.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jagdish Gediya [Wed, 21 Mar 2018 19:38:10 +0000 (01:08 +0530)]
mtd: nand: fsl_ifc: Read ECCSTAT0 and ECCSTAT1 registers for IFC 2.0
commit
6b00c35138b404be98b85f4a703be594cbed501c upstream.
Due to missing information in Hardware manual, current
implementation doesn't read ECCSTAT0 and ECCSTAT1 registers
for IFC 2.0.
Add support to read ECCSTAT0 and ECCSTAT1 registers during
ecccheck for IFC 2.0.
Fixes:
656441478ed5 ("mtd: nand: ifc: Fix location of eccstat registers for IFC V1.0")
Cc: stable@vger.kernel.org # v3.18+
Signed-off-by: Jagdish Gediya <jagdish.gediya@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jagdish Gediya [Wed, 21 Mar 2018 00:21:46 +0000 (05:51 +0530)]
mtd: nand: fsl_ifc: Fix eccstat array overflow for IFC ver >= 2.0.0
commit
843c3a59997f18060848b8632607dd04781b52d1 upstream.
Number of ECC status registers i.e. (ECCSTATx) has been increased in IFC
version 2.0.0 due to increase in SRAM size. This is causing eccstat
array to over flow.
So, replace eccstat array with u32 variable to make it fail-safe and
independent of number of ECC status registers or SRAM size.
Fixes:
bccb06c353af ("mtd: nand: ifc: update bufnum mask for ver >= 2.0.0")
Cc: stable@vger.kernel.org # 3.18+
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Jagdish Gediya <jagdish.gediya@nxp.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jagdish Gediya [Tue, 20 Mar 2018 23:01:36 +0000 (04:31 +0530)]
mtd: nand: fsl_ifc: Fix nand waitfunc return value
commit
fa8e6d58c5bc260f4369c6699683d69695daed0a upstream.
As per the IFC hardware manual, Most significant 2 bytes in
nand_fsr register are the outcome of NAND READ STATUS command.
So status value need to be shifted and aligned as per the nand
framework requirement.
Fixes:
82771882d960 ("NAND Machine support for Integrated Flash Controller")
Cc: stable@vger.kernel.org # v3.18+
Signed-off-by: Jagdish Gediya <jagdish.gediya@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
OuYang ZhiZhong [Sun, 11 Mar 2018 07:59:07 +0000 (15:59 +0800)]
mtdchar: fix usage of mtd_ooblayout_ecc()
commit
6de564939e14327148e31ddcf769e34105176447 upstream.
Section was not properly computed. The value of OOB region definition is
always ECC section 0 information in the OOB area, but we want to get all
the ECC bytes information, so we should call
mtd_ooblayout_ecc(mtd, section++, &oobregion) until it returns -ERANGE.
Fixes:
c2b78452a9db ("mtd: use mtd_ooblayout_xxx() helpers where appropriate")
Cc: <stable@vger.kernel.org>
Signed-off-by: OuYang ZhiZhong <ouyzz@yealink.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Masami Hiramatsu [Sat, 17 Mar 2018 12:38:10 +0000 (21:38 +0900)]
tracing: probeevent: Fix to support minus offset from symbol
commit
c5d343b6b7badd1f5fe0873eff2e8d63a193e732 upstream.
In Documentation/trace/kprobetrace.txt, it says
@SYM[+|-offs] : Fetch memory at SYM +|- offs (SYM should be a data symbol)
However, the parser doesn't parse minus offset correctly, since
commit
2fba0c8867af ("tracing/kprobes: Fix probe offset to be
unsigned") drops minus ("-") offset support for kprobe probe
address usage.
This fixes the traceprobe_split_symbol_offset() to parse minus
offset again with checking the offset range, and add a minus
offset check in kprobe probe address usage.
Link: http://lkml.kernel.org/r/152129028983.31874.13419301530285775521.stgit@devbox
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Tom Zanussi <tom.zanussi@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Ravi Bangoria <ravi.bangoria@linux.vnet.ibm.com>
Cc: stable@vger.kernel.org
Fixes:
2fba0c8867af ("tracing/kprobes: Fix probe offset to be unsigned")
Acked-by: Namhyung Kim <namhyung@kernel.org>
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Larry Finger [Thu, 22 Feb 2018 20:28:59 +0000 (14:28 -0600)]
rtlwifi: rtl8723be: Fix loss of signal
commit
78dc897b7ee67205423dbbc6b56be49fb18d15b5 upstream.
In commit
c713fb071edc ("rtlwifi: rtl8821ae: Fix connection lost problem
correctly") a problem in rtl8821ae that caused loss of signal was fixed.
That same problem has now been reported for rtl8723be. Accordingly,
the ASPM L1 latency has been increased from 0 to 7 to fix the instability.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Tested-by: James Cameron <quozl@laptop.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>