Horatiu Vultur [Wed, 24 Apr 2019 09:27:58 +0000 (11:27 +0200)]
board: mscc: ocelot: Update MSCC Ocelot board.
Implement method board_phy_config to configure the phy for pcb120.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Horatiu Vultur [Wed, 24 Apr 2019 09:27:57 +0000 (11:27 +0200)]
net: mscc: ocelot: Update network driver for pcb120
Update Ocelot network driver to have support also for pcb120.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Horatiu Vultur [Wed, 24 Apr 2019 15:21:29 +0000 (17:21 +0200)]
arch: mips: Update initrd_start and initrd_end
Microsemi SoC defines CONFIG_SYS_SDRAM_BASE to be 0x80000000, which
represents the start of kseg0 and represents a virtual address. Meaning
that the initrd_start and initrd_end point somewhere kseg0.
When these parameters are passed to linux kernel through DT
they are pointing somewhere in kseg0 which is a virtual address but linux
kernel expects the addresses to be physical addresses(in kuseg) because
it is converting the physical address to a virtual one.
Therefore update the uboot to pass the physical address of initrd_start
and initrd_end by converting them using the function virt_to_phys before
setting up the DT.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Robert P. J. Day [Wed, 17 Apr 2019 20:13:45 +0000 (16:13 -0400)]
MSCC: delete obsolete reference to MSCC_BITBANG_SPI_GPIO
Remove "select MSCC_BITBANG_SPI_GPIO" since Kbuild option was deleted
back in commit
ace9c103df2875d2b435dbd7b36618020edfd1c0:
commit
ace9c103df2875d2b435dbd7b36618020edfd1c0
Author: Lars Povlsen <lars.povlsen@microchip.com>
Date: Tue Jan 8 10:38:35 2019 +0100
mips: gpio: mscc: Obsoleted gpio-mscc-bitbang-spi.c
Horatiu Vultur [Thu, 11 Apr 2019 12:11:35 +0000 (14:11 +0200)]
configs: mscc_serval: Add network support
Update default config to use network driver for Serval SoCs.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Horatiu Vultur [Thu, 11 Apr 2019 12:11:34 +0000 (14:11 +0200)]
net: mscc: serval: Add ethernet nodes for Serval
Add ethernet nodes for Serval SoCs family. There are 2 pcb in this
family: pcb105 and pcb106.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Horatiu Vultur [Thu, 11 Apr 2019 12:11:33 +0000 (14:11 +0200)]
board: mscc: serval: Update MSCC Serval boards
In Serval SoC family there are 2 different pcb, both of them have the same
phy, but with different version. Therefore implement board_phy_config
and set all the phys in the same way.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Horatiu Vultur [Thu, 11 Apr 2019 12:11:32 +0000 (14:11 +0200)]
net: Add MSCC Serval network driver.
Add network driver for Microsemi Ethernet switch.
It is present on Serval SoCs.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Horatiu Vultur [Mon, 15 Apr 2019 09:56:37 +0000 (11:56 +0200)]
board: mscc: serval: Fix board detect
When detecting the board, it was reading a register in the GPIO page of
the phy and based on that value it was making a decision. The bug was that
after the GPIO page for the first phy was set it was not reseted back.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Horatiu Vultur [Mon, 15 Apr 2019 09:56:36 +0000 (11:56 +0200)]
mips: mscc: serval: Fix reset
In case the ddr training was failing, it couldn't reset, it was just
hanging. Therefore reimplement it, so when ddr training is failing
it would call _machine_restart, which power downs the DDR and does
a force reset.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Tom Rini [Wed, 1 May 2019 03:21:27 +0000 (23:21 -0400)]
Merge tag 'u-boot-imx-
20190426' of git://git.denx.de/u-boot-imx
Porting to DM and i.MX8
------------------------
- warp7 to DM
- kp_imx53 to DM
- Warnings in DT
- MX8QM support
- colibri-imx6ull to DM
- imx7d-pico to DM
- ocotp for MX8
Tom Rini [Tue, 30 Apr 2019 01:54:04 +0000 (21:54 -0400)]
Prepare v2019.07-rc1
Signed-off-by: Tom Rini <trini@konsulko.com>
Simon Goldschmidt [Sun, 30 Sep 2018 12:31:53 +0000 (14:31 +0200)]
configs: move CONFIG_SPL_TEXT_BASE to Kconfig
Moved CONFIG_SPL_TEXT_BASE to common/spl/Kconfig and migrate existing
values.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
[trini: Re-run migration]
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Mon, 29 Apr 2019 19:54:04 +0000 (15:54 -0400)]
configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Sat, 27 Apr 2019 15:34:55 +0000 (11:34 -0400)]
Revert "fs: btrfs: fix false negatives in ROOT_ITEM search"
Per Pierre this change shouldn't have been applied as it was superseded
by "fs: btrfs: fix btrfs_search_tree invalid results" which is also
applied now as
1627e5e5985d.
This reverts commit
633967f9818cb6a0e87ffa8cba33148a5bcc6edb.
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Sat, 27 Apr 2019 14:42:36 +0000 (10:42 -0400)]
Merge branch '2019-04-27-master-imports'
- Various vexpress, taurus, da850evm, lpc32xx, brxre1 fixes/updates
- btrfs fixes
- Add AM65x HS EVM
- Other small fixes
Igor Opaniuk [Tue, 9 Apr 2019 13:38:14 +0000 (15:38 +0200)]
avb: add support for named persistent values
AVB 2.0 spec. revision 1.1 introduces support for named persistent values
that must be tamper evident and allows AVB to store arbitrary key-value
pairs [1].
Introduce implementation of two additional AVB operations
read_persistent_value()/write_persistent_value() for retrieving/storing
named persistent values.
Correspondent pull request in the OP-TEE OS project repo [2].
[1]: https://android.googlesource.com/platform/external/avb/+/android-9.0.0_r22
[2]: https://github.com/OP-TEE/optee_os/pull/2699
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Igor Opaniuk <igor.opaniuk@gmail.com>
Heinrich Schuchardt [Sun, 21 Apr 2019 21:54:37 +0000 (23:54 +0200)]
arm: dts: add missing vexpress device trees
Add the device trees for
* vexpress_ca5x2_defconfig
* vexpress_ca9x4_defconfig
* vexpress_ca15_tc2_defconfig
as available in Linux 5.1 rc5.
We are using the vexpress_ca15_tc2_defconfig and vexpress_ca9x4_defconfig
for Travis testing via QEMU.
The UEFI base Embedded Base Boot Requirements Specification (EBBR) requires
that an embedded board either provides a device tree or an ACPI table.
All block devices are meant to be moved to the driver model. On ARM this
requires a device tree.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Patrick Delaunay [Thu, 18 Apr 2019 15:16:21 +0000 (17:16 +0200)]
sysreset: syscon: remove POWER reset cause
The sysreset of 'POWER' type is a PMIC reset defined as
'remove and restore power'.
So normally only COLD/WARN is supported by sysreset_syscon.
This modification allows to use the function sysreset_walk(SYSRESET_POWER)
when it is supported by PMIC driver (see example in stpmic1).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Robert P. J. Day [Thu, 18 Apr 2019 12:00:48 +0000 (08:00 -0400)]
doc: delete long-obsolete README.ARM-memory-map
As far back as 2011, "_armboot_start" was being described as "no
longer defined":
commit
297f18ac0fbeef30ba1c17fe131ca75f09a6e7cf
Author: Greg Ungerer <greg.ungerer@opengear.com>
Date: Fri Sep 9 22:23:34 2011 +1000
CM4000: fix broken flash base for OpenGear boards
Use _bss_start_ofs as the size of the boot loader code+data that we want
to protect in the flash. This replaces use of the no longer defined
_armboot_start.
Baruch Siach [Thu, 18 Apr 2019 07:46:58 +0000 (10:46 +0300)]
.gitignore: Ignore .log files
The generated flash.log file that mach-imx uses for MKIMAGEOUTPUT is not
covered by any other ignore pattern. Ignore all *.log files.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Adam Ford [Wed, 17 Apr 2019 18:24:33 +0000 (13:24 -0500)]
ARM: da850evm: Fix TI boot scripts for MMC
The da850evm include environment/ti/mmc.h and places
DEFAULT_MMC_TI_ARGS, defined int that file, in
CONFIG_EXTRA_ENV_SETTINGS. This has been broken for some time
since neither CMD_PART nor CMD_UUID are available, so manually
changing the environmental variables was always required before
booting from MMC. With this patch, these scripts should work
again, and by default they point to mmc 0, partition 2, and
the dtb file exists in a /boot directory on partition 2.
Signed-off-by: Adam Ford <aford173@gmail.com>
Adam Ford [Wed, 17 Apr 2019 16:21:56 +0000 (11:21 -0500)]
ARM: da850evm: Fix broken SPI Flash
A previous patch converted a bunch of settings for CONFIG_SF_DEFAULT
but it broke the SPI Flash which now prevents booting. This patch
now correctly sets CONFIG_SF_DEFAULT_SPEED=
30000000 to match what it
was before the conversion.
Fixes: 14453fbfadc2 ("Convert CONFIG_SF_DEFAULT_* to Kconfig")
Signed-off-by: Adam Ford <aford173@gmail.com>
Björn Stenberg [Wed, 17 Apr 2019 14:56:54 +0000 (16:56 +0200)]
fw_env: Fix double free
addr0 is being freed twice, leading to segmentation fault
Signed-off-by: Björn Stenberg <bjorn@haxx.se>
Gregory CLEMENT [Wed, 17 Apr 2019 09:48:45 +0000 (11:48 +0200)]
arm: lpc32xx: Fix timer initialization
The match controller register is not cleared during
initialization. However, some bits of this register may reset the TC if
tnMRx match it.
As we can't make any assumption about how U-Boot is launched by the first
stage bootloader (such as S1L) clearing this register ensure that the
timers work as expected.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Gregory CLEMENT [Wed, 17 Apr 2019 09:41:42 +0000 (11:41 +0200)]
net: lpc32xx: Use IRAM for transmit buffer
Since the introduction of the driver, some memory in IRAM is reserved for
the TX buffers.
However there are not used but instead of it, it is the buffer provided
by the net stack which is used. As stated in the comment of the driver,
not using the IRAM buffer could cause cache issue and lower the
throughput.
For the second argument it is less the case for transmitting buffers
because the throughput gain in IRAM is mitigated by the time to copy the
data from RAM to IRAM, but the first argument is still valid and indeed
this patch fixes issue seen with Ethernet on some boards
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Gregory CLEMENT [Wed, 17 Apr 2019 09:22:05 +0000 (11:22 +0200)]
mtd: nand: raw: Fix CONFIG_SYS_NAND_DRIVER_ECC_LAYOUT behavior
The purpose of "mtd: nand: raw: allow to disable unneeded ECC layouts"
was to allow disabling the default ECC layouts if a driver is known to
provide its own ECC layout. However, this commit did the opposite and
disabled the default layout when it was _not_ selected.
It breaks all the NAND drivers not providing their own ECC layout this
patch fix this situation.
It was tested with the lpc32xx_nand_slc driver.
Fixes: a38c3af868 ("mtd: nand: raw: allow to disable unneeded ECC layouts")
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Tested-by: Eugen Hristev <eugen.hristev@microchip.com>
Heiko Schocher [Tue, 16 Apr 2019 11:31:58 +0000 (13:31 +0200)]
dtb_platdata.py: prevent define generation of alias
generate define for an alias only if the struct is not
created already.
This prevents compilerwarning:
PLAT spl/dts/dt-platdata.o
spl/dts/dt-platdata.c:11:46: error: missing braces around initializer [-Werror=missing-braces]
static const struct dtd_simple_bus dtv_ahb = {
^
spl/dts/dt-platdata.c:20:46: error: missing braces around initializer [-Werror=missing-braces]
static const struct dtd_simple_bus dtv_apb = {
^
cc1: all warnings being treated as errors
on the at91 based taurus board. Reason is in at91sam9260.dtsi
is defined:
ahb {
compatible = "simple-bus";
ranges;
and later:
pinctrl: pinctrl@
fffff400 {
compatible = "atmel,at91rm9200-pinctrl", "simple-bus";
ranges = <0xfffff400 0xfffff400 0x600>;
without this patch dtoc generates:
struct dtd_atmel_at91rm9200_pinctrl {
fdt32_t atmel_mux_mask[6];
fdt32_t ranges[3];
fdt32_t reg[6];
};
struct dtd_simple_bus {
bool ranges;
};
"#define dtd_simple_bus dtd_atmel_at91rm9200_pinctrl"
and the line with "define dtd_simple_bus..." introduces
the warning. This define is not needed.
Signed-off-by: Heiko Schocher <hs@denx.de>
Pierre Bourdon [Tue, 16 Apr 2019 00:47:14 +0000 (02:47 +0200)]
fs: btrfs: fix btrfs_search_tree invalid results
btrfs_search_tree should return the first item in the tree that is
greater or equal to the searched item.
The search algorithm did not properly handle the edge case where the
searched item is higher than the last item of the node but lower than
the first item of the next node. Instead of properly returning the first
item of the next node, it was returning an invalid path pointer
(pointing to a non-existent item after the last item of the node + 1).
This fixes two issues in the btrfs driver:
- Looking for a ROOT_ITEM could fail if it was the first item of its
leaf node.
- Iterating through DIR_INDEX entries (for readdir) could fail if the
first DIR_INDEX entry was the first item of a leaf node.
Signed-off-by: Pierre Bourdon <delroth@gmail.com>
Cc: Marek Behun <marek.behun@nic.cz>
Ismael Luceno Cortes [Mon, 15 Apr 2019 11:19:15 +0000 (11:19 +0000)]
fs: fat: Build only if CONFIG_FS_FAT=y
Signed-off-by: Ismael Luceno <ismael.luceno@silicon-gears.com>
Pierre Bourdon [Sat, 13 Apr 2019 21:50:49 +0000 (23:50 +0200)]
fs: btrfs: fix false negatives in ROOT_ITEM search
ROOT_ITEMs in btrfs are referenced without knowing their actual "offset"
value. To perform these searches using only two items from the key, the
btrfs driver uses a special "btrfs_search_tree_key_type" function.
The algorithm used by that function to transform a 3-tuple search into a
2-tuple search was subtly broken, leading to items not being found if
they were the first in their tree node.
This commit fixes btrfs_search_tree_key_type to properly behave in these
situations.
Signed-off-by: Pierre Bourdon <delroth@gmail.com>
Cc: Marek Behun <marek.behun@nic.cz>
Andrew F. Davis [Fri, 12 Apr 2019 16:54:48 +0000 (12:54 -0400)]
doc: Update info on using K3 secure devices
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Andreas Dannenberg <dannenberg@ti.com>
Andrew F. Davis [Fri, 12 Apr 2019 16:54:47 +0000 (12:54 -0400)]
configs: Add configs for AM65x High Security EVM
Add new defconfig files for the AM65x High Security EVM.
This defconfigs are the same as for the non-secure part, except for:
CONFIG_TI_SECURE_DEVICE option set to 'y'
CONFIG_FIT_IMAGE_POST_PROCESS option set to 'y'
CONFIG_SPL_FIT_IMAGE_POST_PROCESS option set to 'y'
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Andreas Dannenberg <dannenberg@ti.com>
Andrew F. Davis [Fri, 12 Apr 2019 16:54:46 +0000 (12:54 -0400)]
arm: mach-k3: Add secure device build support
K3 HS devices require signed binaries for boot, use the SECDEV tools
to sign the boot artifacts during build.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Andreas Dannenberg <dannenberg@ti.com>
Andrew F. Davis [Fri, 12 Apr 2019 16:54:45 +0000 (12:54 -0400)]
arm: mach-k3: Add secure device support
K3 devices have High Security (HS) variants along with the non-HS already
supported. Like the previous generation devices (OMAP/Keystone2) K3
supports boot chain-of-trust by authenticating and optionally decrypting
images as they are unpacked from FIT images. Add support for this here.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Andreas Dannenberg <dannenberg@ti.com>
Andrew F. Davis [Fri, 12 Apr 2019 16:54:44 +0000 (12:54 -0400)]
firmware: ti_sci: Modify auth_boot TI-SCI API to match new version
SYSFW version 2019.01 introduces a slightly modified version of this API,
add support for it here.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Andreas Dannenberg <dannenberg@ti.com>
Andrew F. Davis [Fri, 12 Apr 2019 16:54:43 +0000 (12:54 -0400)]
firmware: ti_sci: Add support for firewall management
TI-SCI message protocol provides support for controlling the firewall
configurations available in SoC.
Introduce support for the set of TI-SCI message protocol APIs that
provide us with this capability of controlling firewalls.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Andreas Dannenberg <dannenberg@ti.com>
Andrew F. Davis [Fri, 12 Apr 2019 16:54:42 +0000 (12:54 -0400)]
arm: K3: Avoid use of MCU_PSRAM0 before SYSFW is loaded
On HS devices the 512b region of reset isolated memory called
MCU_PSRAM0 is firewalled by default. Until SYSFW is loaded we
cannot use this memory. It is only used to store a single value
left at the end of SRAM by ROM that will be needed later. Save
that value to a global variable stored in the .data section.
This section is used as .bss will be cleared between saving
this value and using it.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Heiko Schocher [Fri, 12 Apr 2019 10:37:03 +0000 (12:37 +0200)]
main: add new bootstage ID for entering cli loop
adding a new bootstage ID:
BOOTSTAGE_ID_ENTER_CLI_LOOP
Signed-off-by: Heiko Schocher <hs@denx.de>
Patrice Chotard [Thu, 11 Apr 2019 09:13:13 +0000 (11:13 +0200)]
cmd: pxe: Display splashscreen from extlinux.conf input
The objective is to provide a simple way to retrieve a BMP file,
and display it as splashscreen, from extlinux.conf file input.
For this, we take example on https://www.syslinux.org/wiki/
index.php?title=Menu#The_advanced_menu_system
and more particularly on MENU BACKGROUND chapter.
For this, add "menu background" support in pxe command.
As example, extlinux.conf content will look like:
# Generic Distro Configuration file generated by OpenEmbedded
menu title Select the boot mode
TIMEOUT 20
menu background ../splash.bmp
DEFAULT stm32mp157c-ev1-sdcard
LABEL stm32mp157c-ev1-sdcard
KERNEL /uImage
FDT /stm32mp157c-ev1.dtb
APPEND root=/dev/mmcblk0p6 rootwait rw earlyprintk console=ttySTM0,115200
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Pierre Bourdon [Wed, 10 Apr 2019 22:58:49 +0000 (00:58 +0200)]
tools/Makefile: get openssl CFLAGS from pkg-config
Fixes building mkimage on systems where OpenSSL header files do not
live in the standard include path.
Signed-off-by: Pierre Bourdon <delroth@gmail.com>
Heinrich Schuchardt [Wed, 10 Apr 2019 16:59:26 +0000 (18:59 +0200)]
disk: part: fix typo
%g/rathen then/rather than/
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Hannes Schmelzer [Wed, 10 Apr 2019 12:13:16 +0000 (14:13 +0200)]
board/BuR/brxre1: use common resetcontroller implementation
The handling of regarding bootmode and early setup has been moved to
central location 'common/br_resetc.c', so use this on brxre1 board.
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Hannes Schmelzer [Wed, 10 Apr 2019 12:13:15 +0000 (14:13 +0200)]
board/BuR/brxre1: cosmetic cleanup
- fixup coding style
- drop unused 'PUSH_KEY' define
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Hannes Schmelzer [Wed, 10 Apr 2019 12:13:14 +0000 (14:13 +0200)]
board/BuR/common: add br resetcontoller implementation
On many B&R boards we have a reset-controller, responsible for very
early board-bringup (voltages, clocks, ...) and bootmode selection.
To be ready for adding more B&R boards to source tree while avoiding
duplicate code, we add the resetcontroller implementation to the common
part of B&R boards.
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Hannes Schmelzer [Wed, 10 Apr 2019 12:13:13 +0000 (14:13 +0200)]
board/BuR/common: add 'brdefaulip_setup' function
Many B&R boards are equipped with an I2C-EEPROM where various
information can be stored.
Today there is only a single byte for 'board_id' used.
We write this 'board_id' into environment for later use during boot.
If the value != 0xFF, meaning the byte is programmed, we modify the
"brdefaultip" environment variable for setting an IP-Address based on
board_id.
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Hannes Schmelzer [Wed, 10 Apr 2019 12:13:12 +0000 (14:13 +0200)]
board/BuR/common: cosmetic: move 'overwrite_console' up to more related stuff
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Hannes Schmelzer [Wed, 10 Apr 2019 12:13:11 +0000 (14:13 +0200)]
board/BuR/common: prepare for compiling common into non AM33XX boards
Today the BuR common stuff is only used on AM33XX boards. In future we
plan to have many other platforms than AM33XX so we have to move arch-
specific #include(s) to responsible #ifdef sections. By the way we drop
unneeded #include(s).
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Tom Rini [Fri, 26 Apr 2019 17:50:00 +0000 (13:50 -0400)]
Merge git://git.denx.de/u-boot-marvell
- Add DM based generic watchdog start and reset implementation
and remove all ad-hoc implementations (Stefan)
- Move mv_sdhci to DM (Pierre)
- Misc turris_omnia updates (Pierre)
- Change openrd targets to correctly build again (size changes
and fixes to the dts targets) and bring it back into Travis
builds (Stefan)
- Add Kirkwood db-
88f6281-bp board (Chris)
Tom Rini [Fri, 26 Apr 2019 17:49:58 +0000 (13:49 -0400)]
Merge branch 'master' of git://git.denx.de/u-boot-socfpga
Stefan Roese [Thu, 25 Apr 2019 09:53:18 +0000 (11:53 +0200)]
arm: kirkwood: openrd: Mark openrd boards as maintained again
With the latest size increase of the openrd boards, they all compile
clean again. Let's mark them as maintained again and add the Travis
job.
Please note that I can only compile-test these targets as I don't
have access to one of those boards.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Albert ARIBAUD <albert-u-boot@aribaud.net>
Cc: Vagrant Cascadian <vagrant@debian.org>
Cc: Chris Packham <judge.packham@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
Stefan Roese [Thu, 11 Apr 2019 13:58:47 +0000 (15:58 +0200)]
watchdog: at91sam9_wdt: Remove now superfluous wdt start and reset
With the new generic function, the scattered other functions are now
removed to be replaced by the generic one. The new version also enables
the configuration of the watchdog timeout via the DT "timeout-sec"
property (if enabled via CONFIG_OF_CONTROL).
The watchdog servicing is enabled via CONFIG_WATCHDOG.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Stefan Roese [Thu, 11 Apr 2019 13:58:46 +0000 (15:58 +0200)]
watchdog: mpc8xx_wdt: Watchdog driver and macros cleanup
With the generic watchdog driver now implemented, this patch removes
some legacy stuff from the MPC8xx watchdog driver and its Kconfig
integration. CONFIG_MPC8xx_WATCHDOG is completely removed and
hw_watchdog_reset() is made static, as the watchdog will now get
serviced via the DM infrastructure if enabled via CONFIG_WATCHDOG.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Stefan Roese [Thu, 11 Apr 2019 13:58:45 +0000 (15:58 +0200)]
watchdog: cadence: Remove driver specific "timeout-sec" handling
Now that we have a generic DT property "timeout-sec" handling, the
driver specific implementation can be dropped.
This patch also changes the timeout restriction to the min and max
values (clipping). Before this patch, the value provided via
"timeout-sec" was used if the parameter was too high or low. Now
the driver specific min and max values are used instead.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Tested-by: Michal Simek <michal.simek@xilinx.com> (on zcu100)
Stefan Roese [Thu, 11 Apr 2019 13:58:44 +0000 (15:58 +0200)]
watchdog: Implement generic watchdog_reset() version
This patch tries to implement a generic watchdog_reset() function that
can be used by all boards that want to service the watchdog device in
U-Boot. This watchdog servicing is enabled via CONFIG_WATCHDOG.
Without this approach, new boards or platforms needed to implement a
board specific version of this functionality, mostly copy'ing the same
code over and over again into their board or platforms code base.
With this new generic function, the scattered other functions are now
removed to be replaced by the generic one. The new version also enables
the configuration of the watchdog timeout via the DT "timeout-sec"
property (if enabled via CONFIG_OF_CONTROL).
This patch also adds a new flag to the GD flags, to flag that the
watchdog is ready to use and adds the pointer to the watchdog device
to the GD. This enables us to remove the global "watchdog_dev"
variable, which was prone to cause problems because of its potentially
very early use in watchdog_reset(), even before the BSS is cleared.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: "Marek Behún" <marek.behun@nic.cz>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Maxim Sloyko <maxims@google.com>
Cc: Erik van Luijk <evanluijk@interact.nl>
Cc: Ryder Lee <ryder.lee@mediatek.com>
Cc: Weijie Gao <weijie.gao@mediatek.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: "Álvaro Fernández Rojas" <noltari@gmail.com>
Cc: Philippe Reynes <philippe.reynes@softathome.com>
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Tested-by: Michal Simek <michal.simek@xilinx.com> (on zcu100)
Stefan Roese [Wed, 24 Apr 2019 14:05:06 +0000 (16:05 +0200)]
arm: mvebu: turris_omnia: Use thumb instructions in SPL to save space
With the latest changes to the drivers (SPI_FLASH_SPANSION etc), Travis
reports that the SPL image is too big. Let's use the thumb instructions
in SPL to save some space and make the image fit again.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: Marek Behun <marek.behun@nic.cz>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Chris Packham [Sat, 13 Apr 2019 08:21:19 +0000 (20:21 +1200)]
ARM: kirkwood: enable CONFIG_DM_USB on db-
88f6281-bp
Switch to the driver model for USB on the db-
88f6281-bp board.
CONFIG_BLK can't be enabled yet because mvebu_mmc.c needs converting.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Chris Packham [Sat, 13 Apr 2019 08:21:18 +0000 (20:21 +1200)]
ARM: kirkwood: add db-
88f6281-bp board
This is Marvell's Kirkwood development board. It has the following
features
- 512M DDR2
- 2 PCI connectors
- 1 x1 PCI-e interface
- 1 Gigabit Ethernet Port
- 2 SATA Ports
- USB 2.0 Interface
- SDIO
- 128M NAND Flash
- 16M SPI Flash
It can be strapped to boot from SPI or NAND so there are two defconfigs
(one per boot media).
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Michael Walle [Thu, 11 Apr 2019 13:36:21 +0000 (15:36 +0200)]
arm: kirkwood: lsxl: add note about sata in README
The boot commands have changed in the environment. Add a note about the
incompatible change and how resolve the issue in the board's README.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Stefan Roese [Thu, 11 Apr 2019 10:33:36 +0000 (12:33 +0200)]
arm: kirkwood: openrd: Increase U-Boot size in flash to make it fit
We have run now multiple times into size issues with the openrd
board port. To finally fix this, this patch now moves the U-Boot size
from 0x6.0000 to 0x8.0000, giving enough space for the next time.
This also changes the environment location and potentially the
MTD partitioning, but I see no better fix for now. Especially since
this board does not have an active maintainer.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Stefan Roese [Thu, 11 Apr 2019 10:33:35 +0000 (12:33 +0200)]
arm: kirkwood: openrd: Remove superfluous CONFIG_ENV_ADDR
Remove the superfluous CONFIG_ENV_ADDR definition. Its not needed
as CONFIG_ENV_OFFSET is also set to the same value.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Stefan Roese [Thu, 11 Apr 2019 10:33:34 +0000 (12:33 +0200)]
arm: kirkwood: dts: Add openrd-* dtb makefile build targets
The following Kirkwood dtb build targets are currently missing:
kirkwood-openrd-base.dtb
kirkwood-openrd-client.dtb
kirkwood-openrd-ultimate.dtb
This patch adds them to the Makefile to fix the build error.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Pierre Bourdon [Thu, 11 Apr 2019 02:56:59 +0000 (04:56 +0200)]
arm: mvebu: turris_omnia: use MMC driver model
Enable DM_MMC for compliance with the driver model migration.
Signed-off-by: Pierre Bourdon <delroth@gmail.com>
Cc: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
Pierre Bourdon [Thu, 11 Apr 2019 02:56:58 +0000 (04:56 +0200)]
mmc: mv_sdhci: add driver model support
The new DM implementation currently does not support the Sheeva
88SV331xV5 specific quirk present in the legacy implementation. The
legacy code is thus kept for this SoC and others not yet migrated to
DM_MMC.
Signed-off-by: Pierre Bourdon <delroth@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Stefan Roese <sr@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Pierre Bourdon [Wed, 10 Apr 2019 23:00:23 +0000 (01:00 +0200)]
arm: mvebu: turris_omnia: fix eeprom/mcu device names
Commit
c4bd12a7dad4 ("i2c: mux: Generate longer i2c mux name") changed
the naming scheme of i2c devices within a mux. This broke references to
i2c@0 in the Turris Omnia board initialization code.
Signed-off-by: Pierre Bourdon <delroth@gmail.com>
Cc: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
Igor Opaniuk [Mon, 15 Apr 2019 09:01:57 +0000 (11:01 +0200)]
colibri_imx6: use UUID for rootfs
1. Replace usage of "/dev/mmcblk*p*" with a proper UUID of rootfs
partition. This fixes the issue, when MMC controllers are probed in
a different order in U-boot and Linux kernel.
2. Fix legacy USB command (both sdboot and usbboot can be used now).
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Pierre-Jean Texier [Fri, 19 Apr 2019 18:34:12 +0000 (20:34 +0200)]
warp7: Switch to DM USB
This commit switches to DM USB for warp7 and warp7_bl33 defconfigs.
Signed-off-by: Pierre-Jean Texier <pjtexier@koncepto.io>
Signed-off-by: Joris Offouga <offougajoris@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Pierre-Jean Texier [Fri, 19 Apr 2019 18:34:11 +0000 (20:34 +0200)]
warp7: Switch to DM Serial
This commit switches to DM SERIAL for warp7 and warp7_bl33 defconfigs.
Signed-off-by: Pierre-Jean Texier <pjtexier@koncepto.io>
Signed-off-by: Joris Offouga <offougajoris@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Peng Fan [Mon, 22 Apr 2019 10:41:28 +0000 (10:41 +0000)]
ddr: imx8m: hide i.MX8M DDR options from device driver entry
Use one menu to hide the several i.MX8M DDR options from device
driver entry.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Marcel Ziswiler [Wed, 17 Apr 2019 23:57:32 +0000 (01:57 +0200)]
ARM: dts: colibri-imx6ull: update device tree
Fix compatible node to use regular Toradex notation.
Annotate device tree with standard Colibri pin muxing comments.
Use open-drain I2C pin muxings.
Alphabetically re-order iomuxc nodes.
Rename snvs-ad7879-int-grp touch interrupt node as per Linux device tree.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Marcel Ziswiler [Wed, 17 Apr 2019 23:57:31 +0000 (01:57 +0200)]
ARM: dts: colibri-imx6ull: add osc32k_32k_out pinctrl
Add GPIO1_IO03__OSC32K_32K_OUT pin muxing.
While at it also fix indentation of pinfunc header file.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Marcel Ziswiler [Wed, 17 Apr 2019 23:47:36 +0000 (01:47 +0200)]
ARM: dts: i.MX6Q: fix avoid_unnecessary_addr_size warnings
Re-synced the device tree with Linux 5.0.
This fixes the following warnings:
w+arch/arm/dts/imx6-apalis.dtb: Warning (reg_format): /soc/ipu@
2800000/
port@2/endpoint@0:reg: property has invalid length (4 bytes)
(#address-cells == 2, #size-cells == 1)
w+arch/arm/dts/imx6-apalis.dtb: Warning (reg_format): /soc/ipu@
2800000/
port@2/endpoint@1:reg: property has invalid length (4 bytes)
(#address-cells == 2, #size-cells == 1)
w+arch/arm/dts/imx6-apalis.dtb: Warning (reg_format): /soc/ipu@
2800000/
port@2/endpoint@2:reg: property has invalid length (4 bytes)
(#address-cells == 2, #size-cells == 1)
w+arch/arm/dts/imx6-apalis.dtb: Warning (reg_format): /soc/ipu@
2800000/
port@2/endpoint@3:reg: property has invalid length (4 bytes)
(#address-cells == 2, #size-cells == 1)
w+arch/arm/dts/imx6-apalis.dtb: Warning (reg_format): /soc/ipu@
2800000/
port@2/endpoint@4:reg: property has invalid length (4 bytes)
(#address-cells == 2, #size-cells == 1)
w+arch/arm/dts/imx6-apalis.dtb: Warning (reg_format): /soc/ipu@
2800000/
port@3/endpoint@1:reg: property has invalid length (4 bytes)
(#address-cells == 2, #size-cells == 1)
w+arch/arm/dts/imx6-apalis.dtb: Warning (reg_format): /soc/ipu@
2800000/
port@3/endpoint@2:reg: property has invalid length (4 bytes)
(#address-cells == 2, #size-cells == 1)
w+arch/arm/dts/imx6-apalis.dtb: Warning (reg_format): /soc/ipu@
2800000/
port@3/endpoint@3:reg: property has invalid length (4 bytes)
(#address-cells == 2, #size-cells == 1)
w+arch/arm/dts/imx6-apalis.dtb: Warning (reg_format): /soc/ipu@
2800000/
port@3/endpoint@4:reg: property has invalid length (4 bytes)
(#address-cells == 2, #size-cells == 1)
w+arch/arm/dts/imx6-apalis.dtb: Warning (avoid_default_addr_size):
/soc/ipu@
2800000/port@2/endpoint@0: Relying on default #address-cells
value
w+arch/arm/dts/imx6-apalis.dtb: Warning (avoid_default_addr_size):
/soc/ipu@
2800000/port@2/endpoint@0: Relying on default #size-cells
value
w+arch/arm/dts/imx6-apalis.dtb: Warning (avoid_default_addr_size):
/soc/ipu@
2800000/port@2/endpoint@1: Relying on default #address-cells
value
w+arch/arm/dts/imx6-apalis.dtb: Warning (avoid_default_addr_size):
/soc/ipu@
2800000/port@2/endpoint@1: Relying on default #size-cells
value
w+arch/arm/dts/imx6-apalis.dtb: Warning (avoid_default_addr_size):
/soc/ipu@
2800000/port@2/endpoint@2: Relying on default #address-cells
value
w+arch/arm/dts/imx6-apalis.dtb: Warning (avoid_default_addr_size):
/soc/ipu@
2800000/port@2/endpoint@2: Relying on default #size-cells
value
w+arch/arm/dts/imx6-apalis.dtb: Warning (avoid_default_addr_size):
/soc/ipu@
2800000/port@2/endpoint@3: Relying on default #address-cells
value
w+arch/arm/dts/imx6-apalis.dtb: Warning (avoid_default_addr_size):
/soc/ipu@
2800000/port@2/endpoint@3: Relying on default #size-cells
value
w+arch/arm/dts/imx6-apalis.dtb: Warning (avoid_default_addr_size):
/soc/ipu@
2800000/port@2/endpoint@4: Relying on default #address-cells
value
w+arch/arm/dts/imx6-apalis.dtb: Warning (avoid_default_addr_size):
/soc/ipu@
2800000/port@2/endpoint@4: Relying on default #size-cells
value
w+arch/arm/dts/imx6-apalis.dtb: Warning (avoid_default_addr_size):
/soc/ipu@
2800000/port@3/endpoint@1: Relying on default #address-cells
value
w+arch/arm/dts/imx6-apalis.dtb: Warning (avoid_default_addr_size):
/soc/ipu@
2800000/port@3/endpoint@1: Relying on default #size-cells
value
w+arch/arm/dts/imx6-apalis.dtb: Warning (avoid_default_addr_size):
/soc/ipu@
2800000/port@3/endpoint@2: Relying on default #address-cells
value
w+arch/arm/dts/imx6-apalis.dtb: Warning (avoid_default_addr_size):
/soc/ipu@
2800000/port@3/endpoint@2: Relying on default #size-cells
value
w+arch/arm/dts/imx6-apalis.dtb: Warning (avoid_default_addr_size):
/soc/ipu@
2800000/port@3/endpoint@3: Relying on default #address-cells
value
w+arch/arm/dts/imx6-apalis.dtb: Warning (avoid_default_addr_size):
/soc/ipu@
2800000/port@3/endpoint@3: Relying on default #size-cells
value
w+arch/arm/dts/imx6-apalis.dtb: Warning (avoid_default_addr_size):
/soc/ipu@
2800000/port@3/endpoint@4: Relying on default #address-cells
value
w+arch/arm/dts/imx6-apalis.dtb: Warning (avoid_default_addr_size):
/soc/ipu@
2800000/port@3/endpoint@4: Relying on default #size-cells
value
w+arch/arm/dts/imx6-apalis.dtb: Warning (avoid_unnecessary_addr_size):
Failed prerequisite 'avoid_default_addr_size'
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Parthiban Nallathambi [Wed, 17 Apr 2019 22:04:09 +0000 (00:04 +0200)]
imx: Add variscite DART-6UL Evaluation Kit
Port for the DART-6UL Evaluation Kit SBC. Based on the variscite
DART-6UL iMX6ULL SoM.
CPU: Freescale i.MX6ULL rev1.1 900 MHz (running at 396 MHz)
CPU: Commercial temperature grade (0C to 95C) at 43C
Reset cause: POR
Model: Variscite DART-6UL Evaluation Kit
Board: Variscite DART-6UL Evaluation Kit
DRAM: 512 MiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
In: serial@
02020000
Out: serial@
02020000
Err: serial@
02020000
Net: FEC0
Working:
- Eth0
- i2c
- MMC/SD
- eMMC
- USB host
- UART 1
Note: LCDIF porting needs DM_VIDEO
https://lists.denx.de/pipermail/u-boot/2019-April/365506.html
Signed-off-by: Parthiban Nallathambi <parthitce@gmail.com>
Ye Li [Wed, 17 Apr 2019 09:41:23 +0000 (09:41 +0000)]
mxc_ocotp: Disable fuse sense for imx8mq B1
On iMX8MQ Rev B1, reading from fuse box is not allowed. The
OCOTP_READ_FUSE_DATA register is tied to magic number 0xff0055aa
for chip rev. So u-boot has to disable the fuse sense function for it.
Signed-off-by: Ye Li <ye.li@nxp.com>
Tested-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Ye Li [Wed, 17 Apr 2019 09:41:20 +0000 (09:41 +0000)]
mxc_ocotp: Update redundancy banks for mx7ulp B0
On mx7ulp B0, beside bank 0 and 1, the fuse bank 9, 10, 28 are changed to
Redundancy mode not ECC, so they can support to program different bits of
a word in multiple times.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Wed, 17 Apr 2019 09:41:16 +0000 (09:41 +0000)]
imx: i.MX8MQ: clear ocotp error bit
In case ocotp error bit is set, clear it.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Mon, 15 Apr 2019 12:00:50 +0000 (12:00 +0000)]
imx: 8qxp_mek: fix fdt_file and console
Fix fdt_file and console to boot upstream Linux Kernel.
Upstream linux use imx8qxp-mek.dtb, and pass lpuart32 to earlycon
will not work for i.MX8QXP, only need to pass earlycon,
check drivers/tty/serial/earlycon.c,
" /* Just 'earlycon' is a valid param for devicetree and ACPI SPCR. */ "
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Ludwig Zenz [Mon, 15 Apr 2019 09:13:08 +0000 (11:13 +0200)]
ARM: imx6: DHCOM i.MX6 PDK: use Kconfig for inclusion of DDR calibration
The four x16 DDR3 are wired in T-topology. From NXP AN4467:
'Although not required, T-Topologies may also benefit from performing
Write Leveling as there are package delays on both the processor and DDR
devices that can be de-skewed by performing Write Leveling. Therefore,
Freescale recommends determining Write Leveling calibration parameters
for all boards, regardless of topology used.'
That is why write level calibration is also done.
Signed-off-by: Ludwig Zenz <lzenz@dh-electronics.com>
Ludwig Zenz [Mon, 15 Apr 2019 07:31:10 +0000 (09:31 +0200)]
ARM: imx6: update 1GB DDR3 calibration for DHCOM i.MX6qd PDK
The existing calibration values were found to be incorrect
in comparison to newly determined values.
The new values were generated with the help of 5 boards. They have
been determined with the NXP Utility 'DDR Stress Test (2.9.0)'.
Signed-off-by: Ludwig Zenz <lzenz@dh-electronics.com>
Peng Fan [Mon, 15 Apr 2019 05:20:43 +0000 (05:20 +0000)]
imx: add lowlevel init for ARM64
Sometimes we met SERROR, but only to catch it when Linux boots up.
Let's enable catching in U-Boot to catch it ealier and ease debug.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Chris Packham [Sat, 13 Apr 2019 08:21:48 +0000 (20:21 +1200)]
ARM: imx: Fix typo in select option for ZMX25
Correct CPU_ARM926EJS1 to CPU_ARM926EJS.
Reported-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Pierre-Jean Texier [Fri, 12 Apr 2019 20:36:36 +0000 (22:36 +0200)]
warp7: Fix dfu_alt_info setting after DM conversion
After DM conversion, U-Boot is larger than 512 KiB, so we need to increase
the "size" of the dfu_alt_info setting.
Signed-off-by: Pierre-Jean Texier <pjtexier@koncepto.io>
Acked-by: Joris Offouga <offougajoris@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Filip Brozovic [Fri, 12 Apr 2019 09:59:55 +0000 (11:59 +0200)]
dts: imx6ull: add USB aliases to support DM
Signed-off-by: Filip Brozovic <fbrozovic@gmail.com>
Stefano Babic [Thu, 25 Apr 2019 14:25:03 +0000 (16:25 +0200)]
imx8qxp_mek: drop warning due to unused variable
Signed-off-by: Stefano Babic <sbabic@denx.de>
Joris Offouga [Thu, 4 Apr 2019 12:00:56 +0000 (14:00 +0200)]
pico-imx7d: Increase u-boot size for dfu request
After DM conversion, the size of U-Boot binary to increase.
Previous size is 480K after DM Conversion the new size is 557K
So it's necessary to increase the dfu request for store u-boot-dtb.img in eMMC.
Signed-off-by: Joris Offouga <offougajoris@gmail.com>
Joris Offouga [Thu, 4 Apr 2019 12:00:55 +0000 (14:00 +0200)]
pico-imx7d: Convert DM MMC
This patch enable convert DM MMC for imx7d-pico board and variant.
Before the DM conversion only usdhc3 was enabled and therefore it appeared
as MMC 0 to u-boot. After enabling MMC DM though usdhc3 defaults to MMC 2,
which left unattended would drive changes to existing pico-pi bootscripts and
environment variables that rely on mmc 0.
Setup the alias of mmc0 and usdhc3 so that existing pico-imx7d boot code will
work unmodified.
When converting to DM_MMC it is necessary that SPL initializes eMMC
by itself, so move the original eMMC initialization from U-Boot
proper to SPL.
Signed-off-by: Joris Offouga <offougajoris@gmail.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Marcel Ziswiler [Tue, 9 Apr 2019 15:25:33 +0000 (17:25 +0200)]
board: toradex: tdx-cfg-block: add new skus
Add all the latest new SKUs:
- Apalis iMX8 QuadXPlus 2GB Wi-Fi / BT IT
- Apalis iMX8 QuadMax 4GB IT
- Apalis iMX8 QuadPlus 2GB Wi-Fi / BT
- Apalis iMX8 QuadPlus 2GB",
- Colibri iMX8 QuadXPlus 2GB IT
- Colibri iMX8 DualX 1GB Wi-Fi / Bluetooth
- Colibri iMX8 DualX 1GB
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Joris Offouga [Thu, 4 Apr 2019 12:00:54 +0000 (14:00 +0200)]
pico-imx7d: defconfig Enable DM gpio pinctrl and pinctrl_imx7
This patch is necessary for convert this board to dm driver model
DM GPIO requires gpio_request() to be called explicitly before
doing any gpio operation
Signed-off-by: Joris Offouga <offougajoris@gmail.com>
Marcel Ziswiler [Tue, 9 Apr 2019 15:25:32 +0000 (17:25 +0200)]
board: toradex: tdx-cfg-block: clean-up sku handling
Clean-up handling of several SKUs.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Joris Offouga [Thu, 4 Apr 2019 12:00:53 +0000 (14:00 +0200)]
pico-imx7d: defconfig: Add DT file hooks
This patch adds DT file hooks for Pico i.MX7D SOM and variant boards
Signed-off-by: Joris Offouga <offougajoris@gmail.com>
Marcel Ziswiler [Tue, 9 Apr 2019 15:25:31 +0000 (17:25 +0200)]
arm: dts: imx8dx: add lpuart1, lpuart2, lpuart3
Add support for lpuart1, lpuart2 and lpuart3.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Marcel Ziswiler [Tue, 9 Apr 2019 15:25:30 +0000 (17:25 +0200)]
misc: imx8: remove duplicates from scfw api
Remove duplicate function declarations from the SCFW API header file.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Joris Offouga [Thu, 4 Apr 2019 12:00:52 +0000 (14:00 +0200)]
Arm: imx7d-pico: Import all Linux device tree for Pico i.MX7D SOM
This patch imports the Linux kernel base board imx7d-pico.dtsi,
pi board imx7d-pico-pi.dts and hobbit board imx7d-pico-hobbit.dts
from Linux v5.1-rc1.
Signed-off-by: Joris Offouga <offougajoris@gmail.com>
Marcel Ziswiler [Tue, 9 Apr 2019 15:24:18 +0000 (17:24 +0200)]
ARM: dts: colibri-imx6ull: fix uart-has-rtscts property
Remove vendor pre-fix fsl, from uart-has-rtscts property.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Marcel Ziswiler [Tue, 9 Apr 2019 15:24:17 +0000 (17:24 +0200)]
colibri-imx6ull: migrate fec to using driver model
Migrate Ethernet FEC to using driver model.
Drop PHY_MICREL_KSZ90X1 which slipped in from Apalis iMX6.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Marcel Ziswiler [Tue, 9 Apr 2019 15:24:16 +0000 (17:24 +0200)]
colibri-imx6ull: migrate usb to using driver model
Migrate USB to using driver model.
Add USBH_PEN GPIO regulator.
While at it also add alias e.g. as required for UMS.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Marcel Ziswiler [Tue, 9 Apr 2019 15:24:15 +0000 (17:24 +0200)]
colibri-imx6ull: migrate mmc to using driver model
Migrate MMC to using driver model.
Migrate USDHC to using pinctrl.
While at it also add GPIO1_IO03__OSC32K_32K_OUT pin muxing.
While at it also update copyright period.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Marcel Ziswiler [Tue, 9 Apr 2019 15:24:14 +0000 (17:24 +0200)]
colibri-imx6ull: migrate pinctrl and regulators to dtb/dm
Migrate pinctrl and regulators to device tree resp. driver model:
Ethernet, NAND and UART.
Drop BOARD_EARLY_INIT_F as it is anyway no longer used.
Enable CMD_DM, CMD_MTD, CMD_REGULATOR and DM_REGULATOR_FIXED.
While at it also update copyright period.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Marcel Ziswiler [Tue, 9 Apr 2019 15:24:13 +0000 (17:24 +0200)]
colibri-imx6ull: configuration clean-up
Drop disabling SPL_SYS_THUMB_BUILD as we anyway do not use SPL.
Enbale CRC32 verify, USB SDP and EFI loader support.
Drop CMD_GPT and disabling RANDOM_UUID.
Do savedefconfig which drops USB_FUNCTION_SDP.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Philippe Schenker [Tue, 9 Apr 2019 15:24:12 +0000 (17:24 +0200)]
board: imx6ull: Add disable PMIC_STBY_REQ
Disable output driver of PAD CCM_PMIC_STBY_REQ. This prevents the
SOC to request for a lower voltage during sleep. This is necessary
because the voltage is changing too slow for the SOC to wake up
properly.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>