Revert "drm/i915/hwmon: Enable PL1 power limit"

This reverts commit 0349c41b05968befaffa5fbb7e73d0ee6004f610.

0349c41b0596 ("drm/i915/hwmon: Enable PL1 power limit") is incorrect and
caused a major regression on ATSM. The change enabled the PL1 power limit
but FW sets the default value of the PL1 limit to 0 which implies HW now
works at minimum power and therefore the lowest effective frequency. This
means all workloads now run slower resulting in even GuC FW load operations
timing out, rendering ATSM unusable.

A different solution to the original issue of the PL1 limit being disabled
on ATSM is needed but till that is developed, revert 0349c41b0596.

Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/8062
Signed-off-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230208190312.1611335-1-ashutosh.dixit@intel.com

drm/i915/bios: set default backlight controller index

With backlight controller set to -1 in intel_panel_init_alloc() to
distinguish uninitialized values, and controller later being set only if
it's present in VBT, we can end up with -1 for the controller:

    [drm:intel_bios_init_panel [i915]] VBT backlight PWM modulation
    frequency 200 Hz, active high, min brightness 0, level 255,
    controller 4294967295

There's no harm if it happens on platforms that ignore controller due to
only one backlight controller being present, like on VLV above, but play
it safe.

Fixes: bf38bba3e7d6 ("drm/i915: Try to use the correct power sequencer intiially on bxt/glk")
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230207111626.1839645-1-jani.nikula@intel.com

drm/i915/uncore: cast iomem to avoid sparse warning

drmm_add_action_or_reset() is unaware of __iomem and the pointer needs
to be a plain void *. Cast __iomem away and back while the pointer goes
through drmm.

drivers/gpu/drm/i915/intel_uncore.c:2463:17: warning: incorrect type in argument 1 (different address spaces)
drivers/gpu/drm/i915/intel_uncore.c:2463:17:    expected void volatile [noderef] __iomem *addr
drivers/gpu/drm/i915/intel_uncore.c:2463:17:    got void *regs
drivers/gpu/drm/i915/intel_uncore.c:2494:16: warning: incorrect type in argument 3 (different address spaces)
drivers/gpu/drm/i915/intel_uncore.c:2494:16:    expected void *data
drivers/gpu/drm/i915/intel_uncore.c:2494:16:    got void [noderef] __iomem *regs

Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230207124026.2105442-2-jani.nikula@intel.com

drm/i915/dmc: drop "ucode" from function names

The ucode part in the init, fini, suspend and resume function names is
just unnecessary. Drop it.

Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230207110619.1821992-1-jani.nikula@intel.com

drm/i915: Pick the backlight controller based on VBT on ICP+

Use the second backlight controller on ICP+ if the VBT asks
us to do so.

On pre-MTP we also check the chicken bit to make sure the
pins have been correctly muxed by the firmware.

Cc: stable@vger.kernel.org
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/8016
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230207064337.18697-4-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Populate encoder->devdata for DSI on icl+

We now have some eDP+DSI dual panel systems floating around
where the DSI panel is the secondary LFP and thus needs to
consult "panel type 2" in VBT in order to locate all the
other panel type dependant stuff correctly.

To that end we need to pass in the devdata to
intel_bios_init_panel_late(), otherwise it'll just assume
we want the primary panel type. So let's try to just populate
the vbt.ports[] stuff and encoder->devdata for icl+ DSI
panels as well.

We can't do this on older platforms as there we risk a DSI
port aliasing with a HDMI/DP port, which is a totally legal
thing as the DSI ports live in their own little parallel
universe.

Cc: stable@vger.kernel.org
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/8016
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230207064337.18697-3-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Fix VBT DSI DVO port handling

Turns out modern (icl+) VBTs still declare their DSI ports
as MIPI-A and MIPI-C despite the PHYs now being A and B.
Remap appropriately to allow the panels declared as MIPI-C
to work.

Cc: stable@vger.kernel.org
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/8016
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230207064337.18697-2-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Fix memory leaks in scatterlist

This patch fixes memory leaks on error escapes in i915_scatterlist.c

Fixes: c3bfba9a2225 ("drm/i915: Check for integer truncation on scatterlist creation")
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Matt Atwood <matthew.s.atwood@intel.com>
Reviewed-by: Harish Chegondi <harish.chegondi@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230201232801.123684-1-matthew.s.atwood@intel.com

drm/i915: Add another EHL pci id

described as "32 Execution Unit (EU) Super SKU" in:
Intel Atom x6000E Series, and Intel Pentium and Celeron N and
J Series Processors for IoT Applications
Datasheet, Volume 1
Document Number: 636112-1.6

Signed-off-by: Jonathan Gray <jsg@jsg.id.au>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230206043727.46069-1-jsg@jsg.id.au

drm/i915/hwmon: Enable PL1 power limit

Previous documentation suggested that PL1 power limit is always
enabled. However we now find this not to be the case on some
platforms (such as ATSM). Therefore enable PL1 power limit during hwmon
initialization.

Bspec: 51864

v2: Add Bspec reference (Gwan-gyeong)
v3: Add Fixes tag

Fixes: 99f55efb79114 ("drm/i915/hwmon: Power PL1 limit and TDP setting")
Signed-off-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230203155309.1042297-1-ashutosh.dixit@intel.com

drm/i915/dsb: Introduce intel_dsb_finish()

Introduce a function to emits whatever commands we need
at the end of the DSB command buffer. For the moment we
only do the tail cacheline alignment there, but eventually
we might want to eg. emit an interrupt.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230118163040.29808-5-ville.syrjala@linux.intel.com
Reviewed-by: Animesh Manna <animesh.manna@intel.com>

drm/i915/dsb: Split intel_dsb_wait() from intel_dsb_commit()

Starting the DSB execution vs. waiting for it stop are two
totally different things. Split intel_dsb_wait() from
intel_dsb_commit() so that we can eventually allow the DSB
to execute asynchronously.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230118163040.29808-4-ville.syrjala@linux.intel.com
Reviewed-by: Animesh Manna <animesh.manna@intel.com>

drm/i915/dsb: Pimp debug/error prints

Print the crtc/DSB id information to make it clear which DSB engine
we're talking about.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230118163040.29808-3-ville.syrjala@linux.intel.com
Reviewed-by: Animesh Manna <animesh.manna@intel.com>

drm/i915/fbdev: Implement fb_dirty for intel custom fb helper

After disconnecting damage worker from update logic it's left to fbdev
emulation implementation to have fb_dirty function. Currently intel
fbdev doesn't have it. This is causing problems to features (PSR, FBC,
DRRS) relying on dirty callback.

Implement simple fb_dirty callback to deliver notifications about updates
in fb console.

v4: Add proper Fixes tag and modify commit message
v3: Check damage clip
v2: Improved commit message and added Fixes tag

Fixes: f231af498c29 ("drm/fb-helper: Disconnect damage worker from update logic")
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230123074437.475103-1-jouni.hogander@intel.com

drm/i915/dmc: check incoming dmc id validity

Add validity checks for the dmc ids computed from pipe parameters in
intel_dmc_enable_pipe() and intel_dmc_disable_pipe(). It's slightly
difficult for humans and static analyzers alike to ensure the resulting
dmc ids are within bounds. Just check them and reject invalid ones.

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/6a349c3a2b2def5fc31a48c9844ebd72ee55a22b.1675339447.git.jani.nikula@intel.com

drm/i915/dmc: add is_valid_dmc_id() and use it

Add a name to the dmc id validity check.

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/311213ce328575a95d793a219d4dac7d947086cc.1675339447.git.jani.nikula@intel.com

drm/i915/dmc: remove unnecessary dmc_id validity check

The dmc_id comes from for_each_dmc_id() in parse_dmc_fw() ->
parse_dmc_fw_header() -> dmc_mmio_addr_sanity_check(). It's valid by
definition.

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/b4e1c862687f79861a5fa4bfa6797ecda2136fab.1675339447.git.jani.nikula@intel.com

drm/i915/dmc: add for_each_dmc_id() and use it

The loop is duplicated many times, with slightly different ways. Unify.

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/8dcaa716093e6fbe75bb69ee7ac715a3f007a523.1675339447.git.jani.nikula@intel.com

drm/i915/dmc: add proper name to dmc id enum and use it

Clarify DMC ID usage by adding enum intel_dmc_id name to the enum, and
use dmc_id as the variable name for it throughout.

Convert a switch-case to if-ladder to avoid warnings about not handling
DMC_FW_MAX enumeration constant in the switch-case.

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/6912ccb411bb957c68c108b774745dbc7e0cbdc2.1675339447.git.jani.nikula@intel.com

drm/i915: Expose SAGV state via debugfs

Since SAGV is controlled via unidirectional pcode commands
we have no way to query the current state. So instead let's
expose the last programmed state via debugfs. This way we
can at least know whether SAGV should be enabled or not
(which can be important to know when dealing with underruns/etc.).

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230131002127.29305-4-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Keep sagv status updated on icl+

On icl+ SAGV is controlled by masking of the QGV points.
Reduce the QGV point mask to the same kind of enabled vs.
disable information that we had on previous platforms.
Will be useful in answering the question whether SAGV is
actually enabled or not.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230131002127.29305-3-ville.syrjala@linux.intel.com
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>

drm/i915: Introduce HAS_SAGV()

Introuce a HAS_SAGV() macro to answer the question whether
the platform in general supports SAGV. intel_has_sagv() will
keep on giving us the more specific answer whether the current
device supports SAGV or not.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230131002127.29305-2-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Don't do the WM0->WM1 copy w/a if WM1 is already enabled

Due to a workaround we have to make sure the WM1 watermarks block/lines
values are sensible even when WM1 is disabled. To that end we copy those
values from WM0.

However since we now keep each wm level enabled on a per-plane basis
it doesn't seem necessary to do that copy when we already have an
enabled WM1 on the current plane. That is, we might be in a situation
where another plane can only do WM0 (and thus needs the copy) but
the current plane's WM1 is still perfectly valid (ie. fits into the
current DDB allocation).

Skipping the copy could avoid reprogramming the plane's registers
needlessly in some cases.

Fixes: a301cb0fca2d ("drm/i915: Keep plane watermarks enabled more aggressively")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230131002127.29305-1-ville.syrjala@linux.intel.com
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>

drm/i915/lvds: s/pipe_config/crtc_state/

Call the crtc state 'crtc_state' rather than 'pipe_config',
as is the modern style.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230130180540.8972-9-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915/lvds: s/intel_encoder/encoder/ etc.

Get rid of some of the annoying aliasing drm_ vs.
intel_ encoder/connector variables. Just prefer the
intel_ types.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230130180540.8972-8-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915/lvds: s/dev_priv/i915/

Do the customary s/dev_priv/i915/ rename and aliasing
'dev' pointer removal. Though various register definitions
still depend on the magic 'dev_priv' variable so not
a 100% conversion.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230130180540.8972-7-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915/lvds: Fix whitespace

Replace some stray spaces with tabs.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230130180540.8972-6-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915/lvds: Extract intel_lvds_regs.h

Extract the integrated LVDS port register definitions
into their own header file.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230130180540.8972-5-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915/lvds: Use REG_BIT() & co.

Use REG_BIT() & co. for the LVDS port register.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230130180540.8972-4-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915/lvds: Use intel_de_rmw()

Replace the hand rolled rmw stuff with intel_de_rmw().

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230130180540.8972-3-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915/lvds: Split long lines

Split some overly long lines.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230130180540.8972-2-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Implement workaround for CDCLK PLL disable/enable

It was reported that we might get a hung and loss of register access in
some cases when CDCLK PLL is disabled and then enabled, while squashing
is enabled.
As a workaround it was proposed by HW team that SW should disable squashing
when CDCLK PLL is being reenabled.

v2: - Added WA number comment(Rodrigo Vivi)

Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230130135836.12738-1-stanislav.lisovskiy@intel.com

drm/i915/hdmi: Go for scrambling only if platform supports TMDS clock > 340MHz

There are cases, where devices have an HDMI1.4 retimer, and TMDS clock rate
is capped to 340MHz via VBT. In such cases scrambling might be supported
by the platform and an HDMI2.0 sink for lower TMDS rates, but not
supported by the retimer, causing blankouts.

So avoid enabling scrambling, if the TMDS clock is capped to <= 340MHz.

v2: Added comment, documenting the rationale to check for TMDS clock,
before going for scrambling. (Arun)

v3: Fixed the function name to check if source supports scrambling. (Jani)

Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Arun R Murthy <arun.r.murthy@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221222040851.3029514-1-ankit.k.nautiyal@intel.com

drm/i915/dg1: Drop final use of IS_DG1_GRAPHICS_STEP

All production DG1 hardware has graphics stepping B0; there is no such
thing as C0.  As such, we can simplify

        IS_DG1_GRAPHICS_STEP(uncore->i915, STEP_A0, STEP_C0)

to just match DG1 in general.

Bspec: 44463
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230127224313.4042331-4-matthew.d.roper@intel.com

drm/i915/dg1: Drop support for pre-production steppings

Several post-DG1 platforms have been brought up now, so we're well past
the point where we usually drop the workarounds that are only applicable
to internal/pre-production hardware.

Production DG1 hardware always has a B0 stepping for both display and
GT.

Bspec: 44463
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230127224313.4042331-3-matthew.d.roper@intel.com

drm/i915/tgl: Drop support for pre-production steppings

Several post-TGL platforms have been brought up now, so we're well past
the point where we usually drop the workarounds that are only applicable
to internal/pre-production hardware.

Production TGL hardware always has display stepping C0 or later and GT
stepping B0 or later (this is true for both the original TGL and the U/Y
subplatform).

Bspec 44455
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230127224313.4042331-2-matthew.d.roper@intel.com

drm/i915: implement async_flip mode per plane tracking

Current implementation of async flip w/a relies on assumption that
previous atomic commit contains valid information if async_flip is still
enabled on the plane. It is incorrect. If previous commit did not modify
the plane its state->uapi.async_flip can be false. As a result DMAR/PIPE
errors can be observed:
i915 0000:00:02.0: [drm] *ERROR* Fault errors on pipe A: 0x00000080
i915 0000:00:02.0: [drm] *ERROR* Fault errors on pipe A: 0x00000080
DMAR: DRHD: handling fault status reg 2
DMAR: [DMA Read NO_PASID] Request device [00:02.0] fault addr 0x0 [fault reason 0x06] PTE Read access is not set

v2: update async_flip_planes in more reliable places (Ville)
v3: reset async_flip_planes and do_async_flip in more scenarios (Ville)
v4: move all resets to plane loops (Ville)

Signed-off-by: Andrzej Hajda <andrzej.hajda@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230127153003.2225111-1-andrzej.hajda@intel.com

drm/i915/psr: Split sel fetch plane configuration into arm and noarm

SEL_FETCH_CTL registers are armed immediately when plane is disabled.
SEL_FETCH_* instances of plane configuration are used when doing
selective update and normal plane register instances for full updates.
Currently all SEL_FETCH_* registers are written as a part of noarm
plane configuration. If noarm and arm plane configuration are not
happening within same vblank we may end up having plane as a part of
selective update before it's PLANE_SURF register is written.

Fix this by splitting plane selective fetch configuration into arm and
noarm versions and call them accordingly. Write SEL_FETCH_CTL in arm
version.

v3:
 - add arm suffix into intel_psr2_disable_plane_sel_fetch
v2:
 - drop color_plane parameter from arm part
 - dev_priv -> i915 in arm part

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Mika Kahola <mika.kahola@intel.com>
Cc: Vinod Govindapillai <vinod.govindapillai@intel.com>
Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Cc: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230130080651.3796929-1-jouni.hogander@intel.com

drm/i915/display/dsi: use intel_de_rmw if possible

The helper makes the code more compact and readable.

Signed-off-by: Andrzej Hajda <andrzej.hajda@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221219130844.2914001-1-andrzej.hajda@intel.com

drm/i915/display/vlv: use intel_de_rmw if possible

The helper makes the code more compact and readable.

Signed-off-by: Andrzej Hajda <andrzej.hajda@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221219092428.2515430-2-andrzej.hajda@intel.com

drm/i915/display/vlv: fix pixel overlap register update

To update properly bits in the register the mask should be used
to clear old value and then the result should be or-ed with new
value, for such updates there is separate helper intel_de_rmw.

Signed-off-by: Andrzej Hajda <andrzej.hajda@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221219092428.2515430-1-andrzej.hajda@intel.com

drm/i915/display/fdi: use intel_de_rmw if possible

The helper makes the code more compact and readable.

Signed-off-by: Andrzej Hajda <andrzej.hajda@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221215125610.1161729-1-andrzej.hajda@intel.com

drm/i915/adlp: Fix typo for reference clock

Fix typo for reference clock from 24400 to 24000.

Bspec: 55409
Fixes: 626426ff9ce4 ("drm/i915/adl_p: Add cdclk support for ADL-P")
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Chaitanya Kumar Borah <chaitanya.kumar.borah@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230112094131.550252-1-chaitanya.kumar.borah@intel.com

drm/i915/pxp: Pxp hw init should be in resume_complete

During suspend flow, i915 currently achors' on the pm_suspend_prepare
callback as the location where we quiesce the entire GPU and perform
all necessary cleanup in order to go into suspend. PXP is also called
during this time to perform the arbitration session teardown (with
the assurance no additional GEM IOCTLs will come after that could
restart the session).

However, if other devices or drivers fail their suspend_prepare, the
system will not go into suspend and i915 will be expected to resume
operation. In this case, we need to re-initialize the PXP hardware
and this really should be done within the pm_resume_complete callback
which is the correct opposing function in the resume sequence to
match pm_suspend_prepare of the suspend sequence.

Because this callback is the last thing at the end of resuming
we expect little to no impact to the rest of the i915 resume sequence
with this change.

Signed-off-by: Alan Previn <alan.previn.teres.alexis@intel.com>
Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230125082637.118970-7-alan.previn.teres.alexis@intel.com

drm/i915/pxp: Trigger the global teardown for before suspending

A driver bug was recently discovered where the security firmware was
receiving internal HW signals indicating that session key expirations
had occurred. Architecturally, the firmware was expecting a response
from the GuC to acknowledge the event with the firmware side.
However the OS was in a suspended state and GuC had been reset.

Internal specifications actually required the driver to ensure
that all active sessions be properly cleaned up in such cases where
the system is suspended and the GuC potentially unable to respond.

This patch adds the global teardown code in i915's suspend_prepare
code path.

v2 : Split __pxp_global_teardown_locked helper into two variants
     for teardown-with-restart vs teardown-for-suspend/shutdown.

Signed-off-by: Alan Previn <alan.previn.teres.alexis@intel.com>
Reviewed-by: Juston Li <justonli@chromium.org>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230125082637.118970-6-alan.previn.teres.alexis@intel.com

drm/i915/pxp: Invalidate all PXP fw sessions during teardown

A gap was recently discovered where if an application did not
invalidate all of the stream keys (intentionally or not), and the
driver did a full PXP global teardown on the GT subsystem, we
find that future session creation would fail on the security
firmware's side of the equation. i915 is the entity that needs
ensure the sessions' state across both iGT and security firmware
are at a known clean point when performing a full global teardown.

Architecturally speaking, i915 should inspect all active sessions
and submit the invalidate-stream-key PXP command to the security
firmware for each of them. However, for the upstream i915 driver
we only support the arbitration session that can be created
so that will be the only session we will cleanup.

Signed-off-by: Alan Previn <alan.previn.teres.alexis@intel.com>
Reviewed-by: Juston Li <justonli@chromium.org>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230125082637.118970-5-alan.previn.teres.alexis@intel.com

mei: clean pending read with vtag on bus

Client on bus have only one vtag map slot and should disregard the vtag
value when cleaning pending read flag.
Fixes read flow control message unexpectedly generated when
clent on bus send messages with different vtags.

Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Reviewed-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Alan Previn <alan.previn.teres.alexis@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230125082637.118970-4-alan.previn.teres.alexis@intel.com

drm/i915/pxp: add device link between i915 and mei_pxp

Add device link with i915 as consumer and mei_pxp as supplier
to ensure proper ordering of power flows.

V2: condition on absence of heci_pxp to filter out DG

Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Alan Previn <alan.previn.teres.alexis@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230125082637.118970-3-alan.previn.teres.alexis@intel.com

mei: mei-me: resume device in prepare

Asynchronous runtime resume is not possible while the system
is suspending.
The power management subsystem resumes the device only in the
suspend phase, not in the prepare phase.
Force resume device in prepare to allow drivers on mei bus
to communicate in their prepare callbacks.

Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Reviewed-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Alan Previn <alan.previn.teres.alexis@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230125082637.118970-2-alan.previn.teres.alexis@intel.com

drm/i915: Convert PALETTE() to _PICK_EVEN_2RANGES()

PALETTE() can use _PICK_EVEN_2RANGES instead of _PICK, which
reduces the size and is safer.

Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Anusha Srivatsa<anusha.srivatsa@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230120193457.3295977-9-lucas.demarchi@intel.com

drm/i915: Convert MBUS_ABOX_CTL() to _PICK_EVEN_2RANGES()

MBUS_ABOX_CTL() can use _PICK_EVEN_2RANGES instead of _PICK, which
reduces the size and is safer.

Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230120193457.3295977-8-lucas.demarchi@intel.com

drm/i915: Convert _FIA() to _PICK_EVEN_2RANGES()

_FIA() can use _PICK_EVEN_2RANGES instead of _PICK, which reduces the
size and is safer.

Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230120193457.3295977-7-lucas.demarchi@intel.com

drm/i915: Convert PIPE3/PORT3 to _PICK_EVEN_2RANGES()

Like done for when __var_args__ were used, but size-wise it's also
benefitial to avoid _PICK() used for 3 ports/pipes:

$ size build64/drivers/gpu/drm/i915/i915.o{.old,.new}
   text    data     bss     dec     hex filename
4026288  185703    6984 4218975  40605f build64/drivers/gpu/drm/i915/i915.o.old
4025496  185703    6984 4218183  405d47 build64/drivers/gpu/drm/i915/i915.o.new

Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230120193457.3295977-6-lucas.demarchi@intel.com

drm/i915: Replace _MMIO_PHY3() with _PICK_EVEN_2RANGES()

As done previously for pll, also convert users of _PHY3() to
_PICK_EVEN_2RANGES(). Size comparison of i915.o:

$ size build64/drivers/gpu/drm/i915/i915.o{.old,.new}
   text    data     bss     dec     hex filename
4026997  185703    6984 4219684  406324 build64/drivers/gpu/drm/i915/i915.o.old
4026288  185703    6984 4218975  40605f build64/drivers/gpu/drm/i915/i915.o.new

Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230120193457.3295977-5-lucas.demarchi@intel.com

drm/i915: Convert pll macros to _PICK_EVEN_2RANGES

Avoid the array lookup, converting the PLL macros after ICL to
_PICK_EVEN_RANGES. This provides the following reduction in code size:

$ size build64/drivers/gpu/drm/i915/i915.o{.old,.new}
   text    data     bss     dec     hex filename
4027456  185703    6984 4220143  4064ef build64/drivers/gpu/drm/i915/i915.o.old
4026997  185703    6984 4219684  406324 build64/drivers/gpu/drm/i915/i915.o.new

At the same time it's safer, avoiding out-of-bounds array access.  This
allows to remove _MMIO_PLL3() that is now unused.

Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230120193457.3295977-4-lucas.demarchi@intel.com

drm/i915: Fix coding style on DPLL*_ENABLE defines

Abide by the rules in the top of the header: 2 spaces for bitfield,
prefix offsets with underscore and prefer the use of REG_BIT().

Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230120193457.3295977-3-lucas.demarchi@intel.com

drm/i915: Add _PICK_EVEN_2RANGES()

It's a constant pattern in the driver to need to use 2 ranges of MMIOs
based on port, phy, pll, etc. When that happens, instead of using
_PICK_EVEN(), _PICK() needs to be used.  Using _PICK() is discouraged
due to some reasons like:

1) It increases the code size since the array is declared
   in each call site
2) Developers need to be careful not to incur an
   out-of-bounds array access
3) Developers need to be careful that the indexes match the
   table. For that it may be that the table needs to contain
   holes, making (1) even worse.

Add a variant of _PICK_EVEN() that works with 2 ranges and selects which
one to use depending on the index value.

v2: Fix the address expansion in the example (Anusha)
v3: Also rename macro to _PICK_EVEN_2RANGES() in the documentation
    and reword it to clarify what ranges are chosen based on the index
    (Jani)

Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230125182403.7526-1-lucas.demarchi@intel.com

drm/i915/mtl: Apply Wa_14013475917 for all MTL steppings

Wa_14013475917 has to be applied for all MTL steppings.

Bspec: 66624

Cc: Mika Kahola <mika.kahola@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230124102636.2567292-3-jouni.hogander@intel.com

drm/i915/psr: Implement Wa_14014971492

Implement Wa_14014971492 and apply it for affected platforms.

Bspec: 52890, 54369, 55378, 66624

v2: Adjust platforms where applied

Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Mika Kahola <mika.kahola@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230124102636.2567292-2-jouni.hogander@intel.com

drm/i915/panel: move panel fixed EDID to struct intel_panel

It's a bit confusing to have two cached EDIDs in struct intel_connector
with slightly different purposes. Make the distinction a bit clearer by
moving the EDID cached for eDP and LVDS panels at connector init time to
struct intel_panel, and name it fixed_edid. That's what it is, a fixed
EDID for the panels.

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/328350ef918638928a8286cdbab3107c8258332d.1674643465.git.jani.nikula@intel.com

drm/i915/opregion: convert intel_opregion_get_edid() to struct drm_edid

Simplify validation and use by converting to drm_edid.

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/6abb01f1e97d54a3c11bec24377f035df412b492.1674643465.git.jani.nikula@intel.com

drm/i915/bios: convert intel_bios_init_panel() to drm_edid

Try to use struct drm_edid where possible, even if having to fall back
to looking into struct edid down low via drm_edid_raw().

v2: Rebase

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/897807d62f74f690a173ecd405e25c6ccdd63b98.1674643465.git.jani.nikula@intel.com

drm/i915/edid: convert DP, HDMI and LVDS to drm_edid

Convert all the connectors that use cached connector edid and
detect_edid to drm_edid.

Since drm_get_edid() calls drm_connector_update_edid_property() while
drm_edid_read*() do not, we need to call drm_edid_connector_update()
separately, in part due to the EDID caching behaviour in HDMI and
DP. Especially DP depends on the details parsed from EDID. (The big
behavioural change conflating EDID reading with parsing and property
update was done in commit 5186421cbfe2 ("drm: Introduce epoch counter to
drm_connector"))

v6: Rebase on drm_edid_connector_add_modes()

v5: Fix potential uninitialized var use (kernel test robot <lkp@intel.com>)

v4: Call drm_edid_connector_update() after reading HDMI/DP EDID

v3: Don't leak vga switcheroo EDID in LVDS init (Ville)

v2: Don't leak opregion fallback EDID (Ville)

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/eabb4de932841b38b34cc2818ea9fbf7c10224fd.1674643465.git.jani.nikula@intel.com

drm/i915/params: use generics for parameter debugfs file creation

Replace the __builtin_strcmp() if ladder with generics.

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230118151800.3669913-4-jani.nikula@intel.com

drm/i915/params: use generics for parameter free

Replace the __builtin_strcmp() if ladder with generics.

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230118151800.3669913-3-jani.nikula@intel.com

drm/i915/params: use generics for parameter dup

Replace the __builtin_strcmp() if ladder with generics.

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230118151800.3669913-2-jani.nikula@intel.com

drm/i915/params: use generics for parameter printing

Replace the __builtin_strcmp() if ladder with generics.

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230118151800.3669913-1-jani.nikula@intel.com

drm/i915/display: add intel_display_limits.h for key enums

Move a handful of key enums to a new file intel_display_limits.h. These
are the enum types, and the MAX/NUM enumerations within them, that are
used in other headers. Otherwise, there's no common theme between them.

Replace intel_display.h include with intel_display_limit.h where
relevant, and add the intel_display.h include directly in the .c files
where needed.

Since intel_display.h is used almost everywhere in display/, include it
from intel_display_types.h to avoid massive changes across the
board. There are very few files that would need intel_display_types.h
but not intel_display.h so this is neglible, and further cleanup between
these headers can be left for the future.

Overall this change drops the direct and indirect dependencies on
intel_display.h from about 300 to about 100 compilation units, because
we can drop the include from i915_drv.h.

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230116164644.1752009-1-jani.nikula@intel.com

drm/i915/gmch: move VGA set state to GMCH code

This is the only user for the GMCH bridge device in display. Move it to
GMCH code.

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/9bd50fe508246a547cf6e7abfe44ed686a4b3e3a.1673958757.git.jani.nikula@intel.com

drm/i915/gmch: mass rename dev_priv to i915

Prefer the contemporary naming.

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/3e4aaadeb4a027165f5724027963aa5e8d747190.1673958757.git.jani.nikula@intel.com

drm/i915/gmch: split out soc/intel_gmch

The GMCH related code is a bit too low level and out of place for the
high level i915_driver.c file. Split out to a separate file under
soc/. Rename the functions accordingly.

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/980a5e08b397bc0dbccf93cd84798772233ce75c.1673958757.git.jani.nikula@intel.com

drm/i915: add gmch substruct to struct drm_i915_private

Group the GMCH related members together.

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/c10c8f16cb5d12041e009f788bd9810225d6962d.1673958757.git.jani.nikula@intel.com

drm/i915/audio: Clean up the PCH type checks

Use explicit PCH type checks to make it more clear
which platforms use which codepaths.

Also reorder the branches in ibx_audio_regs_init()
a bit to be more in chronological order.

Cc: Chaitanya Kumar Borah <chaitanya.kumar.borah@intel.com>
Cc: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230124144628.4649-14-ville.syrjala@linux.intel.com

drm/i915/audio: s/ilk/ibx/

Rename the ilk stuff to ibx, as the audio logic lives
in the PCH. The only exception are VLV/CHV but their audio
hardware was stolen from ibx so the name still fits.

Also most of the register defines also use the IBX namespace.

Cc: Chaitanya Kumar Borah <chaitanya.kumar.borah@intel.com>
Cc: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230124144628.4649-13-ville.syrjala@linux.intel.com

drm/i915/audio: Include ELD in the state dump

Include the ELD has a hex blob in the crtc state dump.

Cc: Chaitanya Kumar Borah <chaitanya.kumar.borah@intel.com>
Cc: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230124144628.4649-12-ville.syrjala@linux.intel.com

drm/i915/audio: Hook up ELD into the state checker

Have the state checker validate the ELD. For now we'll
just dump it out as a hex buffer on a mismatch, maybe
someone will get inspired to decode it properly at some
point...

Cc: Chaitanya Kumar Borah <chaitanya.kumar.borah@intel.com>
Cc: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230124144628.4649-11-ville.syrjala@linux.intel.com

drm/i915/sdvo: Do ELD hardware readout

Read out the ELD from the hw so the state checker can verify it.

v2: Check the "ELD valid" bit separately
v3: Fix ELD tx rate handling during readout

Cc: Chaitanya Kumar Borah <chaitanya.kumar.borah@intel.com>
Cc: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Jani Nikula <jani.nikula@intel.com> #v1
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230124144628.4649-10-ville.syrjala@linux.intel.com

drm/i915/sdvo: Only use "presence detect" for has_audio readout

Align the SDVO audio code with the native HDMI/DP audio and
use just the "presence detect" bit for the has_audio readout.
The "ELD valid" bit will be used for ELD readout soon.

Cc: Chaitanya Kumar Borah <chaitanya.kumar.borah@intel.com>
Cc: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230124144628.4649-9-ville.syrjala@linux.intel.com

drm/i915/sdvo: Precompute the ELD

Use the precomputed crtc_state->eld for audio setup on SDVO
just like we do with native HDMI.

Cc: Chaitanya Kumar Borah <chaitanya.kumar.borah@intel.com>
Cc: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230124144628.4649-8-ville.syrjala@linux.intel.com

drm/i915/audio: Hardware ELD readout

Read out the ELD from the hardware buffer, or from our stashed
copy for the audio component, so that we can hook up the state
checker to validate it.

v2: Deal with the platforms using acomp

Cc: Chaitanya Kumar Borah <chaitanya.kumar.borah@intel.com>
Cc: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Jani Nikula <jani.nikula@intel.com> #v1
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230124144628.4649-7-ville.syrjala@linux.intel.com

drm/i915/audio: Don't enable audio with bogus ELD

Currently we just print a debug message if the ELD is bogus.
Maybe we should just not enable audio at all in that case?

Cc: Chaitanya Kumar Borah <chaitanya.kumar.borah@intel.com>
Cc: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230124144628.4649-6-ville.syrjala@linux.intel.com

drm/i915/audio: Precompute the ELD

Stash the ELD into the crtc_state and precompute it. This gets
rid of the ugly ELD mutation during intel_audio_codec_enable(),
and opens the door for the state checker.

v2: Make another copy for the acomp hooks (Chaitanya)
    Split out the bogus ELD handling change (Jani)

Cc: Chaitanya Kumar Borah <chaitanya.kumar.borah@intel.com>
Cc: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Jani Nikula <jani.nikula@intel.com> #v1
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230124144628.4649-5-ville.syrjala@linux.intel.com

drm/i915/audio: Introduce a struct for the acomp audio state

Currently we're spreading the stashed state for use of the
audio component hooks all over the place. Start collecting
it up into a single spot.

Cc: Chaitanya Kumar Borah <chaitanya.kumar.borah@intel.com>
Cc: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230124144628.4649-4-ville.syrjala@linux.intel.com

drm/i915/audio: Don't program the hardware ELD buffer on hsw+

Since we use the audio component to transfer the ELD to the audio
driver on hsw+ platforms there is no point in even programming
the hardware ELD buffer. Stop doing so.

The one slight caveat here is that this is not strictly legal
according to the HDA spec. PD=1;ELD=0 is only documented as
an intermediate state during modeset. But if there is no hardware
that depends on that then I guess we're fine. Or we could
perhaps set ELD=1 without actually programming the buffer?

Note that the bspec sequence of PD=0;ELD=0 -> PD=1;ELD=0 ->
PD=1;ELD=1 is also not strictly correct according to the HDA
spec, as the only documented transition from PD=0;ELD=0 is
straight to PD=1;ELD=1.

Additionally on hsw/bdw the hardware buffer is tied in with the
dedicated display HDA controller's power state, so currently
we mostly fail at proramming the buffer anyway. When the HDA
side is not sufficiently powered up the ELD address bits get
stuck and the ELD data register accesses go nowhere.

Cc: Chaitanya Kumar Borah <chaitanya.kumar.borah@intel.com>
Cc: Takashi Iwai <tiwai@suse.de>
References: https://lore.kernel.org/intel-gfx/20221012104936.30911-1-ville.syrjala@linux.intel.com/
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230124144628.4649-3-ville.syrjala@linux.intel.com

drm/i915/audio: Don't program the hardware ELD buffer on ilk+

Since we use the audio component to transfer the ELD to the audio
driver on ilk+ platforms there is no point in even programming
the hardware ELD buffer. Stop doing so.

The one slight caveat here is that this is not strictly legal
according to the HDA spec. PD=1;ELD=0 is only documented as
an intermediate state during modeset. But if there is no hardware
that depends on that then I guess we're fine. Or we could
perhaps set ELD=1 without actually programming the buffer?

Note that the bspec sequence of PD=0;ELD=0 -> PD=1;ELD=0 ->
PD=1;ELD=1 is also not strictly correct according to the HDA
spec, as the only documented transition from PD=0;ELD=0 is
straight to PD=1;ELD=1. But that is not even possible on
these platforms as the bits live in different registers.

Cc: Chaitanya Kumar Borah <chaitanya.kumar.borah@intel.com>
Cc: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230124144628.4649-2-ville.syrjala@linux.intel.com

Merge drm/drm-next into drm-intel-next

Backmerge to get the EDID handling changes.

Signed-off-by: Jani Nikula <jani.nikula@intel.com>

Merge tag 'drm-misc-next-2023-01-24' of git://anongit.freedesktop.org/drm/drm-misc into drm-next

drm-misc-next for v6.3:

UAPI Changes:

Cross-subsystem Changes:

Core Changes:

 * EDID: Improved mode parsing and refactoring

 * fbdev: Cleanups

 * format-helper: Add conversion from XRGB8888 to XBGR8888 and ABGR8888

Driver Changes:

 * accel/ivpu: Add driver for Intel VPU accelerator

 * bridge: Support i.MX93 LDB plus DT bindings

 * exynos: Fixes

 * panel: vtdr6130: Fixes; Support AUO A030JTN01 plus DT bindings

 * simpledrm: Support system-memory framebuffers plus DT bindings

 * ssd130x: Fix sparse warning

Signed-off-by: Dave Airlie <airlied@redhat.com>
# -----BEGIN PGP SIGNATURE-----
#
# iQEzBAABCAAdFiEEchf7rIzpz2NEoWjlaA3BHVMLeiMFAmPQN9YACgkQaA3BHVML
# eiNmmQf/bTV3oaMo55i3tYxhMCWYDtPVk+GGglDAykW7Lid8pvy6mJqJoW6uvgQF
# c6CcoY+6yG2WvnVLhXyhPaACiG5weQSdu3S/DdZ2nuJCb50YCwWNNKcu3qYnLVlz
# 2NQ/s0HN+Xvvy76GJFNarKlxSNADPWCNJ8wExAdBkWr7q8NiDfsWuMGrQRQORrm3
# zEkSJPKtWNHa+vmsQOO9yebD0LFx97CoU40FrVXZTtF0FugGIXjiknQwekzuFxdY
# fGBiFKsI+Y3s51gAppbmRRJ0jGLj3KDF5S+5GM8FNbgJQF67Wxttl/YtY6lJGcsa
# l0vpRoCe1ilhNVvoikzAu7UewkPKKA==
# =GLLt
# -----END PGP SIGNATURE-----
# gpg: Signature made Wed 25 Jan 2023 05:56:06 AEST
# gpg:                using RSA key 7217FBAC8CE9CF6344A168E5680DC11D530B7A23
# gpg: Can't check signature: No public key
From: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/Y9A5ceDknyQixM3R@linux-uq9g

Merge tag 'amd-drm-next-6.3-2023-01-20' of https://gitlab.freedesktop.org/agd5f/linux into drm-next

amd-drm-next-6.3-2023-01-20:

amdgpu:
- Secure display fixes
- Fix scaling
- Misc code cleanups
- Display BW alloc logic updates
- DCN 3.2 fixes
- Fix power reporting on certain firmwares for CZN/RN
- SR-IOV fixes
- Link training cleanup and code rework
- HDCP fixes
- Reserved VMID fix
- Documentation updates
- Colorspace fixes
- RAS updates
- GC11.0 fixes
- VCN instance harvesting fixes
- DCN 3.1.4/5 workarounds for S/G displays
- Add PCIe info to the INFO IOCTL

amdkfd:
- XNACK fix

UAPI:
- Add PCIe gen/lanes info to the amdgpu INFO IOCTL
  Nesa ultimately plans to use this to make decisions about buffer placement optimizations
  Mesa MR: https://gitlab.freedesktop.org/mesa/mesa/-/merge_requests/20790

Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230120234523.7610-1-alexander.deucher@amd.com

drm/i915/dmc: Use unversioned path for ADLP

The new DMC release for ADLP (v2.18) in linux-firmware adopted the new
convention of using unversioned filenames, so update the driver code for
that new release. Keep the latest versioned path as fallback so we do
not cause regressions.

Signed-off-by: Gustavo Sousa <gustavo.sousa@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230123182021.31239-3-gustavo.sousa@intel.com

drm/i915/dmc: Prepare to use unversioned paths

New DMC releases in linux-firmware will stop using version number in
blob filenames. This new convention provides the following benefits:

  1. It simplifies code maintenance, as new DMC releases for a platform
     using the new convention will always use the same filename for the
     blob.

  2. It allows DMC to be loaded even if the target system does not have
     the most recent firmware installed.

Prepare the driver by:

  - Using the new convention for DMC_PATH() and renaming the currently
    used one to make it clear it is for the legacy scheme.

  - Implementing a fallback mechanism for future transitions from
    versioned to unversioned paths so that we do not cause a regression
    for systems not having the most up-to-date linux-firmware files.

v2:
  - Keep using request_firmware() instead of firmware_request_nowarn().
    (Jani)
v3:
  - Keep current DMC paths instead of directly using unversioned ones,
    so that we do not disturb initrd generation.
    (Lucas, Rodrigo)

Signed-off-by: Gustavo Sousa <gustavo.sousa@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230123182021.31239-2-gustavo.sousa@intel.com

Merge tag 'drm-misc-next-2023-01-19' of git://anongit.freedesktop.org/drm/drm-misc into drm-next

drm-misc-next for $kernel-version:

UAPI Changes:

Cross-subsystem Changes:

Core Changes:

 * Cleanup unneeded include statements wrt <linux/fb.h>, <drm/drm_fb_helper.h>
   and <drm/drm_crtc_helper.h>

 * Remove unused helper DRM_DEBUG_KMS_RATELIMITED()

 * fbdev: Remove obsolete aperture field from struct fb_device, plus
   driver cleanups; Remove unused flag FBINFO_MISC_FIRMWARE

 * MIPI-DSI: Fix brightness, plus rsp. driver updates

 * scheduler: Deprecate drm_sched_resubmit_jobs()

 * ttm: Fix MIPS build; Remove ttm_bo_wait(); Documentation fixes

Driver Changes:

 * Remove obsolete drivers for userspace modesetting i810, mga, r128,
   savage, sis, tdfx, via

 * bridge: Support CDNS DSI J721E, plus DT bindings; lt9611: Various
   fixes and improvements; sil902x: Various fixes; Fixes

 * nouveau: Removed support for legacy ioctls; Replace zero-size array;
   Cleanups

 * panel: Fixes

 * radeon: Use new DRM logging helpers

Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/Y8kDk5YX7Yz3eRhM@linux-uq9g

Merge tag 'drm-intel-gt-next-2023-01-18' of git://anongit.freedesktop.org/drm/drm-intel into drm-next

Driver Changes:

Fixes/improvements/new stuff:

- Fix workarounds on Gen2-3 (Tvrtko Ursulin)
- Fix HuC delayed load memory leaks (Daniele Ceraolo Spurio)
- Fix a BUG caused by impendance mismatch in dma_fence_wait_timeout and GuC (Janusz Krzysztofik)
- Add DG2 workarounds Wa_18018764978 and Wa_18019271663 (Matt Atwood)
- Apply recommended L3 hashing mask tuning parameters (Gen12+) (Matt Roper)
- Improve suspend / resume times with VT-d scanout workaround active (Andi Shyti, Chris Wilson)
- Silence misleading "mailbox access failed" warning in snb_pcode_read (Ashutosh Dixit)
- Fix null pointer dereference on HSW perf/OA (Umesh Nerlige Ramappa)
- Avoid trampling the ring during buffer migration (and selftests) (Chris Wilson, Matthew Auld)
- Fix DG2 visual corruption on small BAR systems by not forgetting to copy CCS aux state (Matthew Auld)
- More fixing of DG2 visual corruption by not forgetting to copy CCS aux state of backup objects (Matthew Auld)
- Fix TLB invalidation for Gen12.50 video and compute engines (Andrzej Hajda)
- Limit Wa_22012654132 to just specific steppings (Matt Roper)
- Fix userspace crashes due eviction not working under lock contention after the object locking conversion (Matthew Auld)
- Avoid double free is user deploys a corrupt GuC firmware (John Harrison)
- Fix 32-bit builds by using "%zu" to format size_t (Nirmoy Das)
- Fix a possible BUG in TTM async unbind due not reserving enough fence slots (Nirmoy Das)
- Fix potential use after free by not exposing the GEM context id to userspace too early (Rob Clark)
- Show clamped PL1 limit to the user (hwmon) (Ashutosh Dixit)
- Workaround unreliable reset on Jasperlake (Chris Wilson)
- Cover rest of SVG unit MCR registers (Gustavo Sousa)
- Avoid PXP log spam on platforms which do not support the feature (Alan Previn)
- Re-disable RC6p on Sandy Bridge to avoid GPU hangs and visual glitches (Sasa Dragic)

Future platform enablement:

- Manage uncore->lock while waiting on MCR register (Matt Roper)
- Enable Idle Messaging for GSC CS (Vinay Belgaumkar)
- Only initialize GSC in tile 0 (José Roberto de Souza)
- Media GT and Render GT share common GGTT (Aravind Iddamsetty)
- Add dedicated MCR lock (Matt Roper)
- Implement recommended caching policy (PVC) (Wayne Boyer)
- Add hardware-level lock for steering (Matt Roper)
- Check full IP version when applying hw steering semaphore (Matt Roper)
- Enable GuC GGTT invalidation from the start (Daniele Ceraolo Spurio)
- MTL GSC firmware support (Daniele Ceraolo Spurio, Jonathan Cavitt)
- MTL OA support (Umesh Nerlige Ramappa)
- MTL initial gt workarounds (Matt Roper)

Driver refactors:

- Hold forcewake and MCR lock over PPAT setup (Matt Roper)
- Acquire fw before loop in intel_uncore_read64_2x32 (Umesh Nerlige Ramappa)
- GuC filename cleanups and use submission API version number (John Harrison)
- Promote pxp subsystem to top-level of i915 (Alan Previn)
- Finish proofing the code agains object size overflows (Chris Wilson, Gwan-gyeong Mun)
- Start adding module oriented dmesg output (John Harrison)

Miscellaneous:

- Correct kerneldoc for intel_gt_mcr_wait_for_reg() (Matt Roper)
- Bump up sample period for busy stats selftest (Umesh Nerlige Ramappa)
- Make GuC default_lists const data (Jani Nikula)
- Fix table order verification to check all FW types (John Harrison)
- Remove some limited use register access wrappers (Jani Nikula)
- Remove struct_member macro (Andrzej Hajda)
- Remove hardcoded value with a macro (Nirmoy Das)
- Use helper func to find out map type (Nirmoy Das)
- Fix a static analysis warning (John Harrison)
- Consolidate VMA active tracking helpers (Andrzej Hajda)
- Do not cover all future platforms in TLB invalidation (Tvrtko Ursulin)
- Replace zero-length arrays with flexible-array members (Gustavo A. R. Silva)
- Unwind hugepages to drop wakeref on error (Chris Wilson)
- Remove a couple of superfluous i915_drm.h includes (Jani Nikula)

Merges:

- Merge drm/drm-next into drm-intel-gt-next (Rodrigo Vivi)

danvet: Fix up merge conflict in intel_uc_fw.c, we ended up with 2
copies of try_firmware_load() somehow.

Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/Y8fW2Ny1B1hZ5ZmF@tursulin-desk

drm/i915: update src and dst scaler limits for display ver 12 and 13

The bspec has been updated and now display versions 12 and 13 support
source width up to 5120 pixels, source height up to 8192 lines,
destination width up to 8192 and destination height up to 8192.

Update the code accordingly.

BSpec: 50441
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230113113905.130405-1-luciano.coelho@intel.com

drm/ssd130x: Silence a `dubious: x & !y` warning

The sparse tool complains with the following warning:

$ make M=drivers/gpu/drm/solomon/ C=2
  CC [M]  drivers/gpu/drm/solomon/ssd130x.o
  CHECK   drivers/gpu/drm/solomon/ssd130x.c
drivers/gpu/drm/solomon/ssd130x.c:363:21: warning: dubious: x & !y

This seems to be a false positive in my opinion but still we can silence
the tool while making the code easier to read. Let's also add a comment,
to explain why the "com_seq" logical not is used rather than its value.

Reported-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20230121190930.2804224-1-javierm@redhat.com

fbdev: Remove unused struct fb_deferred_io .first_io field

This optional callback was added in the commit 1f45f9dbb392 ("fb_defio:
add first_io callback") but it was never used by a driver. Let's remove
it since it's unlikely that will be used after a decade that was added.

Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20230121192418.2814955-2-javierm@redhat.com

drm/simpledrm: Support the XB24/AB24 format

Add XB24 and AB24 to the list of supported formats. The format helpers
support conversion to these formats and they are documented in the
simple-framebuffer device tree bindings.

Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230120173103.4002342-8-thierry.reding@gmail.com

drm/format-helper: Support the AB24/XB24 formats

Add a conversion helper for the AB24 and XB24 formats to use in
drm_fb_blit().

Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230120173103.4002342-7-thierry.reding@gmail.com

drm/simpledrm: Add support for system memory framebuffers

Simple framebuffers can be set up in system memory, which cannot be
requested and/or I/O remapped using the I/O resource helpers. Add a
separate code path that obtains system memory framebuffers from the
reserved memory region referenced in the memory-region property.

Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230120173103.4002342-6-thierry.reding@gmail.com

drm/simpledrm: Use struct iosys_map consistently

The majority of the driver already uses struct iosys_map to encapsulate
accesses to I/O remapped vs. system memory. Accesses via the screen base
pointer still use __iomem annotations, which can lead to inconsistencies
and conflicts with subsequent patches.

Convert the screen base to a struct iosys_map as well for consistency
and to avoid these issues.

Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230120173103.4002342-5-thierry.reding@gmail.com

dt-bindings: reserved-memory: Support framebuffer reserved memory

Document the "framebuffer" compatible string for reserved memory nodes
to annotate reserved memory regions used for framebuffer carveouts.

Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230120173103.4002342-4-thierry.reding@gmail.com