Xiaoguang Wang [Thu, 21 Apr 2022 02:37:35 +0000 (10:37 +0800)]
scsi: target: tcmu: Fix possible data corruption
[ Upstream commit
bb9b9eb0ae2e9d3f6036f0ad907c3a83dcd43485 ]
When tcmu_vma_fault() gets a page successfully, before the current context
completes page fault procedure, find_free_blocks() may run and call
unmap_mapping_range() to unmap the page. Assume that when
find_free_blocks() initially completes and the previous page fault
procedure starts to run again and completes, then one truncated page has
been mapped to userspace. But note that tcmu_vma_fault() has gotten a
refcount for the page so any other subsystem won't be able to use the page
unless the userspace address is unmapped later.
If another command subsequently runs and needs to extend dbi_thresh it may
reuse the corresponding slot for the previous page in data_bitmap. Then
though we'll allocate new page for this slot in data_area, no page fault
will happen because we have a valid map and the real request's data will be
lost.
Filesystem implementations will also run into this issue but they usually
lock the page when vm_operations_struct->fault gets a page and unlock the
page after finish_fault() completes. For truncate filesystems lock pages in
truncate_inode_pages() to protect against racing wrt. page faults.
To fix this possible data corruption scenario we can apply a method similar
to the filesystems. For pages that are to be freed, tcmu_blocks_release()
locks and unlocks. Make tcmu_vma_fault() also lock found page under
cmdr_lock. At the same time, since tcmu_vma_fault() gets an extra page
refcount, tcmu_blocks_release() won't free pages if pages are in page fault
procedure, which means it is safe to call tcmu_blocks_release() before
unmap_mapping_range().
With these changes tcmu_blocks_release() will wait for all page faults to
be completed before calling unmap_mapping_range(). And later, if
unmap_mapping_range() is called, it will ensure stale mappings are removed.
Link: https://lore.kernel.org/r/20220421023735.9018-1-xiaoguang.wang@linux.alibaba.com
Reviewed-by: Bodo Stroesser <bostroesser@gmail.com>
Signed-off-by: Xiaoguang Wang <xiaoguang.wang@linux.alibaba.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Lv Ruyi [Sun, 24 Apr 2022 03:19:59 +0000 (03:19 +0000)]
drm: msm: fix error check return value of irq_of_parse_and_map()
[ Upstream commit
b9e4f1d2b505df8e2439b63e67afaa287c1c43e2 ]
The irq_of_parse_and_map() function returns 0 on failure, and does not
return an negative value.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Lv Ruyi <lv.ruyi@zte.com.cn>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/483175/
Link: https://lore.kernel.org/r/20220424031959.3172406-1-lv.ruyi@zte.com.cn
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Alexandru Elisei [Mon, 25 Apr 2022 11:44:41 +0000 (12:44 +0100)]
arm64: compat: Do not treat syscall number as ESR_ELx for a bad syscall
[ Upstream commit
3fed9e551417b84038b15117732ea4505eee386b ]
If a compat process tries to execute an unknown system call above the
__ARM_NR_COMPAT_END number, the kernel sends a SIGILL signal to the
offending process. Information about the error is printed to dmesg in
compat_arm_syscall() -> arm64_notify_die() -> arm64_force_sig_fault() ->
arm64_show_signal().
arm64_show_signal() interprets a non-zero value for
current->thread.fault_code as an exception syndrome and displays the
message associated with the ESR_ELx.EC field (bits 31:26).
current->thread.fault_code is set in compat_arm_syscall() ->
arm64_notify_die() with the bad syscall number instead of a valid ESR_ELx
value. This means that the ESR_ELx.EC field has the value that the user set
for the syscall number and the kernel can end up printing bogus exception
messages*. For example, for the syscall number 0x68000000, which evaluates
to ESR_ELx.EC value of 0x1A (ESR_ELx_EC_FPAC) the kernel prints this error:
[ 18.349161] syscall[300]: unhandled exception: ERET/ERETAA/ERETAB, ESR 0x68000000, Oops - bad compat syscall(2) in syscall[10000+50000]
[ 18.350639] CPU: 2 PID: 300 Comm: syscall Not tainted 5.18.0-rc1 #79
[ 18.351249] Hardware name: Pine64 RockPro64 v2.0 (DT)
[..]
which is misleading, as the bad compat syscall has nothing to do with
pointer authentication.
Stop arm64_show_signal() from printing exception syndrome information by
having compat_arm_syscall() set the ESR_ELx value to 0, as it has no
meaning for an invalid system call number. The example above now becomes:
[ 19.935275] syscall[301]: unhandled exception: Oops - bad compat syscall(2) in syscall[10000+50000]
[ 19.936124] CPU: 1 PID: 301 Comm: syscall Not tainted 5.18.0-rc1-00005-g7e08006d4102 #80
[ 19.936894] Hardware name: Pine64 RockPro64 v2.0 (DT)
[..]
which although shows less information because the syscall number,
wrongfully advertised as the ESR value, is missing, it is better than
showing plainly wrong information. The syscall number can be easily
obtained with strace.
*A 32-bit value above or equal to 0x8000_0000 is interpreted as a negative
integer in compat_arm_syscal() and the condition scno < __ARM_NR_COMPAT_END
evaluates to true; the syscall will exit to userspace in this case with the
ENOSYS error code instead of arm64_notify_die() being called.
Signed-off-by: Alexandru Elisei <alexandru.elisei@arm.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220425114444.368693-3-alexandru.elisei@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Abhishek Kumar [Wed, 27 Apr 2022 07:37:33 +0000 (10:37 +0300)]
ath10k: skip ath10k_halt during suspend for driver state RESTARTING
[ Upstream commit
b72a4aff947ba807177bdabb43debaf2c66bee05 ]
Double free crash is observed when FW recovery(caused by wmi
timeout/crash) is followed by immediate suspend event. The FW recovery
is triggered by ath10k_core_restart() which calls driver clean up via
ath10k_halt(). When the suspend event occurs between the FW recovery,
the restart worker thread is put into frozen state until suspend completes.
The suspend event triggers ath10k_stop() which again triggers ath10k_halt()
The double invocation of ath10k_halt() causes ath10k_htt_rx_free() to be
called twice(Note: ath10k_htt_rx_alloc was not called by restart worker
thread because of its frozen state), causing the crash.
To fix this, during the suspend flow, skip call to ath10k_halt() in
ath10k_stop() when the current driver state is ATH10K_STATE_RESTARTING.
Also, for driver state ATH10K_STATE_RESTARTING, call
ath10k_wait_for_suspend() in ath10k_stop(). This is because call to
ath10k_wait_for_suspend() is skipped later in
[ath10k_halt() > ath10k_core_stop()] for the driver state
ATH10K_STATE_RESTARTING.
The frozen restart worker thread will be cancelled during resume when the
device comes out of suspend.
Below is the crash stack for reference:
[ 428.469167] ------------[ cut here ]------------
[ 428.469180] kernel BUG at mm/slub.c:4150!
[ 428.469193] invalid opcode: 0000 [#1] PREEMPT SMP NOPTI
[ 428.469219] Workqueue: events_unbound async_run_entry_fn
[ 428.469230] RIP: 0010:kfree+0x319/0x31b
[ 428.469241] RSP: 0018:
ffffa1fac015fc30 EFLAGS:
00010246
[ 428.469247] RAX:
ffffedb10419d108 RBX:
ffff8c05262b0000
[ 428.469252] RDX:
ffff8c04a8c07000 RSI:
0000000000000000
[ 428.469256] RBP:
ffffa1fac015fc78 R08:
0000000000000000
[ 428.469276] CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
[ 428.469285] Call Trace:
[ 428.469295] ? dma_free_attrs+0x5f/0x7d
[ 428.469320] ath10k_core_stop+0x5b/0x6f
[ 428.469336] ath10k_halt+0x126/0x177
[ 428.469352] ath10k_stop+0x41/0x7e
[ 428.469387] drv_stop+0x88/0x10e
[ 428.469410] __ieee80211_suspend+0x297/0x411
[ 428.469441] rdev_suspend+0x6e/0xd0
[ 428.469462] wiphy_suspend+0xb1/0x105
[ 428.469483] ? name_show+0x2d/0x2d
[ 428.469490] dpm_run_callback+0x8c/0x126
[ 428.469511] ? name_show+0x2d/0x2d
[ 428.469517] __device_suspend+0x2e7/0x41b
[ 428.469523] async_suspend+0x1f/0x93
[ 428.469529] async_run_entry_fn+0x3d/0xd1
[ 428.469535] process_one_work+0x1b1/0x329
[ 428.469541] worker_thread+0x213/0x372
[ 428.469547] kthread+0x150/0x15f
[ 428.469552] ? pr_cont_work+0x58/0x58
[ 428.469558] ? kthread_blkcg+0x31/0x31
Tested-on: QCA6174 hw3.2 PCI WLAN.RM.4.4.1-00288-QCARMSWPZ-1
Co-developed-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Abhishek Kumar <kuabhs@chromium.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220426221859.v2.1.I650b809482e1af8d0156ed88b5dc2677a0711d46@changeid
Signed-off-by: Sasha Levin <sashal@kernel.org>
Evan Quan [Mon, 25 Apr 2022 02:16:46 +0000 (10:16 +0800)]
drm/amd/pm: fix the compile warning
[ Upstream commit
555238d92ac32dbad2d77ad2bafc48d17391990c ]
Fix the compile warning below:
drivers/gpu/drm/amd/amdgpu/../pm/legacy-dpm/kv_dpm.c:1641
kv_get_acp_boot_level() warn: always true condition '(table->entries[i]->clk >= 0) => (0-u32max >= 0)'
Reported-by: kernel test robot <lkp@intel.com>
CC: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Steven Price [Fri, 3 Dec 2021 10:28:15 +0000 (10:28 +0000)]
drm/plane: Move range check for format_count earlier
[ Upstream commit
4b674dd69701c2e22e8e7770c1706a69f3b17269 ]
While the check for format_count > 64 in __drm_universal_plane_init()
shouldn't be hit (it's a WARN_ON), in its current position it will then
leak the plane->format_types array and fail to call
drm_mode_object_unregister() leaking the modeset identifier. Move it to
the start of the function to avoid allocating those resources in the
first place.
Signed-off-by: Steven Price <steven.price@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Link: https://lore.kernel.org/dri-devel/20211203102815.38624-1-steven.price@arm.com/
Signed-off-by: Sasha Levin <sashal@kernel.org>
Hans de Goede [Wed, 27 Apr 2022 13:49:18 +0000 (15:49 +0200)]
ASoC: Intel: bytcr_rt5640: Add quirk for the HP Pro Tablet 408
[ Upstream commit
ce216cfa84a4e1c23b105e652c550bdeaac9e922 ]
Add a quirk for the HP Pro Tablet 408, this BYTCR tablet has no CHAN
package in its ACPI tables and uses SSP0-AIF1 rather then SSP0-AIF2 which
is the default for BYTCR devices.
It also uses DMIC1 for the internal mic rather then the default IN3
and it uses JD2 rather then the default JD1 for jack-detect.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=211485
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20220427134918.527381-1-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Hari Chandrakanthan [Sat, 23 Apr 2022 09:36:47 +0000 (12:36 +0300)]
ath11k: disable spectral scan during spectral deinit
[ Upstream commit
161c64de239c7018e0295e7e0520a19f00aa32dc ]
When ath11k modules are removed using rmmod with spectral scan enabled,
crash is observed. Different crash trace is observed for each crash.
Send spectral scan disable WMI command to firmware before cleaning
the spectral dbring in the spectral_deinit API to avoid this crash.
call trace from one of the crash observed:
[ 1252.880802] Unable to handle kernel NULL pointer dereference at virtual address
00000008
[ 1252.882722] pgd =
0f42e886
[ 1252.890955] [
00000008] *pgd=
00000000
[ 1252.893478] Internal error: Oops: 5 [#1] PREEMPT SMP ARM
[ 1253.093035] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.4.89 #0
[ 1253.115261] Hardware name: Generic DT based system
[ 1253.121149] PC is at ath11k_spectral_process_data+0x434/0x574 [ath11k]
[ 1253.125940] LR is at 0x88e31017
[ 1253.132448] pc : [<
7f9387b8>] lr : [<
88e31017>] psr:
a0000193
[ 1253.135488] sp :
80d01bc8 ip :
00000001 fp :
970e0000
[ 1253.141737] r10:
88e31000 r9 :
970ec000 r8 :
00000080
[ 1253.146946] r7 :
94734040 r6 :
a0000113 r5 :
00000057 r4 :
00000000
[ 1253.152159] r3 :
e18cb694 r2 :
00000217 r1 :
1df1f000 r0 :
00000001
[ 1253.158755] Flags: NzCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment user
[ 1253.165266] Control:
10c0383d Table:
5e71006a DAC:
00000055
[ 1253.172472] Process swapper/0 (pid: 0, stack limit = 0x60870141)
[ 1253.458055] [<
7f9387b8>] (ath11k_spectral_process_data [ath11k]) from [<
7f917fdc>] (ath11k_dbring_buffer_release_event+0x214/0x2e4 [ath11k])
[ 1253.466139] [<
7f917fdc>] (ath11k_dbring_buffer_release_event [ath11k]) from [<
7f8ea3c4>] (ath11k_wmi_tlv_op_rx+0x1840/0x29cc [ath11k])
[ 1253.478807] [<
7f8ea3c4>] (ath11k_wmi_tlv_op_rx [ath11k]) from [<
7f8fe868>] (ath11k_htc_rx_completion_handler+0x180/0x4e0 [ath11k])
[ 1253.490699] [<
7f8fe868>] (ath11k_htc_rx_completion_handler [ath11k]) from [<
7f91308c>] (ath11k_ce_per_engine_service+0x2c4/0x3b4 [ath11k])
[ 1253.502386] [<
7f91308c>] (ath11k_ce_per_engine_service [ath11k]) from [<
7f9a4198>] (ath11k_pci_ce_tasklet+0x28/0x80 [ath11k_pci])
[ 1253.514811] [<
7f9a4198>] (ath11k_pci_ce_tasklet [ath11k_pci]) from [<
8032227c>] (tasklet_action_common.constprop.2+0x64/0xe8)
[ 1253.526476] [<
8032227c>] (tasklet_action_common.constprop.2) from [<
803021e8>] (__do_softirq+0x130/0x2d0)
[ 1253.537756] [<
803021e8>] (__do_softirq) from [<
80322610>] (irq_exit+0xcc/0xe8)
[ 1253.547304] [<
80322610>] (irq_exit) from [<
8036a4a4>] (__handle_domain_irq+0x60/0xb4)
[ 1253.554428] [<
8036a4a4>] (__handle_domain_irq) from [<
805eb348>] (gic_handle_irq+0x4c/0x90)
[ 1253.562321] [<
805eb348>] (gic_handle_irq) from [<
80301a78>] (__irq_svc+0x58/0x8c)
Tested-on: QCN6122 hw1.0 AHB WLAN.HK.2.6.0.1-00851-QCAHKSWPL_SILICONZ-1
Signed-off-by: Hari Chandrakanthan <quic_haric@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1649396345-349-1-git-send-email-quic_haric@quicinc.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
James Smart [Tue, 26 Apr 2022 18:14:19 +0000 (11:14 -0700)]
scsi: lpfc: Fix resource leak in lpfc_sli4_send_seq_to_ulp()
[ Upstream commit
646db1a560f44236b7278b822ca99a1d3b6ea72c ]
If no handler is found in lpfc_complete_unsol_iocb() to match the rctl of a
received frame, the frame is dropped and resources are leaked.
Fix by returning resources when discarding an unhandled frame type. Update
lpfc_fc_frame_check() handling of NOP basic link service.
Link: https://lore.kernel.org/r/20220426181419.9154-1-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Minghao Chi [Wed, 20 Apr 2022 09:03:52 +0000 (09:03 +0000)]
scsi: ufs: Use pm_runtime_resume_and_get() instead of pm_runtime_get_sync()
[ Upstream commit
75b8715e20a20bc7b4844835e4035543a2674200 ]
Using pm_runtime_resume_and_get() to replace pm_runtime_get_sync() and
pm_runtime_put_noidle(). This change is just to simplify the code, no
actual functional changes.
Link: https://lore.kernel.org/r/20220420090353.2588804-1-chi.minghao@zte.com.cn
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Haohui Mai [Mon, 25 Apr 2022 12:41:38 +0000 (20:41 +0800)]
drm/amdgpu/sdma: Fix incorrect calculations of the wptr of the doorbells
[ Upstream commit
7dba6e838e741caadcf27ef717b6dcb561e77f89 ]
This patch fixes the issue where the driver miscomputes the 64-bit
values of the wptr of the SDMA doorbell when initializing the
hardware. SDMA engines v4 and later on have full 64-bit registers for
wptr thus they should be set properly.
Older generation hardwares like CIK / SI have only 16 / 20 / 24bits
for the WPTR, where the calls of lower_32_bits() will be removed in a
following patch.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Haohui Mai <ricetons@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Lv Ruyi [Mon, 18 Apr 2022 10:57:55 +0000 (10:57 +0000)]
scsi: megaraid: Fix error check return value of register_chrdev()
[ Upstream commit
c5acd61dbb32b6bda0f3a354108f2b8dcb788985 ]
If major equals 0, register_chrdev() returns an error code when it fails.
This function dynamically allocates a major and returns its number on
success, so we should use "< 0" to check it instead of "!".
Link: https://lore.kernel.org/r/20220418105755.2558828-1-lv.ruyi@zte.com.cn
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Lv Ruyi <lv.ruyi@zte.com.cn>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Vignesh Raghavendra [Mon, 25 Apr 2022 06:31:20 +0000 (12:01 +0530)]
drivers: mmc: sdhci_am654: Add the quirk to set TESTCD bit
[ Upstream commit
c7666240ec76422cb7546bd07cc8ae80dc0ccdd2 ]
The ARASAN MMC controller on Keystone 3 class of devices need the SDCD
line to be connected for proper functioning. Similar to the issue pointed
out in sdhci-of-arasan.c driver, commit
3794c542641f ("mmc:
sdhci-of-arasan: Set controller to test mode when no CD bit").
In cases where this can't be connected, add a quirk to force the
controller into test mode and set the TESTCD bit. Use the flag
"ti,fails-without-test-cd", to implement this above quirk when required.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Link: https://lore.kernel.org/r/20220425063120.10135-3-a-govindraju@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Aidan MacDonald [Mon, 11 Apr 2022 15:37:53 +0000 (16:37 +0100)]
mmc: jz4740: Apply DMA engine limits to maximum segment size
[ Upstream commit
afadb04f1d6e74b18a253403f5274cde5e3fd7bd ]
Do what is done in other DMA-enabled MMC host drivers (cf. host/mmci.c) and
limit the maximum segment size based on the DMA engine's capabilities. This
is needed to avoid warnings like the following with CONFIG_DMA_API_DEBUG=y.
------------[ cut here ]------------
WARNING: CPU: 0 PID: 21 at kernel/dma/debug.c:1162 debug_dma_map_sg+0x2f4/0x39c
DMA-API: jz4780-dma
13420000.dma-controller: mapping sg segment longer than device claims to support [len=98304] [max=65536]
CPU: 0 PID: 21 Comm: kworker/0:1H Not tainted 5.18.0-rc1 #19
Workqueue: kblockd blk_mq_run_work_fn
Stack :
81575aec 00000004 80620000 80620000 80620000 805e7358 00000009 801537ac
814c832c 806276e3 806e34b4 80620000 81575aec 00000001 81575ab8 09291444
00000000 00000000 805e7358 81575958 ffffffea 8157596c 00000000 636f6c62
6220646b 80387a70 0000000f 6d5f6b6c 80620000 00000000 81575ba4 00000009
805e170c 80896640 00000001 00010000 00000000 00000000 00006098 806e0000
...
Call Trace:
[<
80107670>] show_stack+0x84/0x120
[<
80528cd8>] __warn+0xb8/0xec
[<
80528d78>] warn_slowpath_fmt+0x6c/0xb8
[<
8016f1d4>] debug_dma_map_sg+0x2f4/0x39c
[<
80169d4c>] __dma_map_sg_attrs+0xf0/0x118
[<
8016a27c>] dma_map_sg_attrs+0x14/0x28
[<
804f66b4>] jz4740_mmc_prepare_dma_data+0x74/0xa4
[<
804f6714>] jz4740_mmc_pre_request+0x30/0x54
[<
804f4ff4>] mmc_blk_mq_issue_rq+0x6e0/0x7bc
[<
804f5590>] mmc_mq_queue_rq+0x220/0x2d4
[<
8038b2c0>] blk_mq_dispatch_rq_list+0x480/0x664
[<
80391040>] blk_mq_do_dispatch_sched+0x2dc/0x370
[<
80391468>] __blk_mq_sched_dispatch_requests+0xec/0x164
[<
80391540>] blk_mq_sched_dispatch_requests+0x44/0x94
[<
80387900>] __blk_mq_run_hw_queue+0xb0/0xcc
[<
80134c14>] process_one_work+0x1b8/0x264
[<
80134ff8>] worker_thread+0x2ec/0x3b8
[<
8013b13c>] kthread+0x104/0x10c
[<
80101dcc>] ret_from_kernel_thread+0x14/0x1c
---[ end trace
0000000000000000 ]---
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Link: https://lore.kernel.org/r/20220411153753.50443-1-aidanmacdonald.0x0@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Heming Zhao [Fri, 1 Apr 2022 02:13:16 +0000 (10:13 +0800)]
md/bitmap: don't set sb values if can't pass sanity check
[ Upstream commit
e68cb83a57a458b01c9739e2ad9cb70b04d1e6d2 ]
If bitmap area contains invalid data, kernel will crash then mdadm
triggers "Segmentation fault".
This is cluster-md speical bug. In non-clustered env, mdadm will
handle broken metadata case. In clustered array, only kernel space
handles bitmap slot info. But even this bug only happened in clustered
env, current sanity check is wrong, the code should be changed.
How to trigger: (faulty injection)
dd if=/dev/zero bs=1M count=1 oflag=direct of=/dev/sda
dd if=/dev/zero bs=1M count=1 oflag=direct of=/dev/sdb
mdadm -C /dev/md0 -b clustered -e 1.2 -n 2 -l mirror /dev/sda /dev/sdb
mdadm -Ss
echo aaa > magic.txt
== below modifying slot 2 bitmap data ==
dd if=magic.txt of=/dev/sda seek=16384 bs=1 count=3 <== destroy magic
dd if=/dev/zero of=/dev/sda seek=16436 bs=1 count=4 <== ZERO chunksize
mdadm -A /dev/md0 /dev/sda /dev/sdb
== kernel crashes. mdadm outputs "Segmentation fault" ==
Reason of kernel crash:
In md_bitmap_read_sb (called by md_bitmap_create), bad bitmap magic didn't
block chunksize assignment, and zero value made DIV_ROUND_UP_SECTOR_T()
trigger "divide error".
Crash log:
kernel: md: md0 stopped.
kernel: md/raid1:md0: not clean -- starting background reconstruction
kernel: md/raid1:md0: active with 2 out of 2 mirrors
kernel: dlm: ... ...
kernel: md-cluster: Joined cluster
44810aba-38bb-e6b8-daca-
bc97a0b254aa slot 1
kernel: md0: invalid bitmap file superblock: bad magic
kernel: md_bitmap_copy_from_slot can't get bitmap from slot 2
kernel: md-cluster: Could not gather bitmaps from slot 2
kernel: divide error: 0000 [#1] SMP NOPTI
kernel: CPU: 0 PID: 1603 Comm: mdadm Not tainted 5.14.6-1-default
kernel: Hardware name: QEMU Standard PC (i440FX + PIIX, 1996)
kernel: RIP: 0010:md_bitmap_create+0x1d1/0x850 [md_mod]
kernel: RSP: 0018:
ffffc22ac0843ba0 EFLAGS:
00010246
kernel: ... ...
kernel: Call Trace:
kernel: ? dlm_lock_sync+0xd0/0xd0 [md_cluster 77fe..7a0]
kernel: md_bitmap_copy_from_slot+0x2c/0x290 [md_mod 24ea..d3a]
kernel: load_bitmaps+0xec/0x210 [md_cluster 77fe..7a0]
kernel: md_bitmap_load+0x81/0x1e0 [md_mod 24ea..d3a]
kernel: do_md_run+0x30/0x100 [md_mod 24ea..d3a]
kernel: md_ioctl+0x1290/0x15a0 [md_mod 24ea....d3a]
kernel: ? mddev_unlock+0xaa/0x130 [md_mod 24ea..d3a]
kernel: ? blkdev_ioctl+0xb1/0x2b0
kernel: block_ioctl+0x3b/0x40
kernel: __x64_sys_ioctl+0x7f/0xb0
kernel: do_syscall_64+0x59/0x80
kernel: ? exit_to_user_mode_prepare+0x1ab/0x230
kernel: ? syscall_exit_to_user_mode+0x18/0x40
kernel: ? do_syscall_64+0x69/0x80
kernel: entry_SYSCALL_64_after_hwframe+0x44/0xae
kernel: RIP: 0033:0x7f4a15fa722b
kernel: ... ...
kernel: ---[ end trace
8afa7612f559c868 ]---
kernel: RIP: 0010:md_bitmap_create+0x1d1/0x850 [md_mod]
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Guoqing Jiang <guoqing.jiang@linux.dev>
Signed-off-by: Heming Zhao <heming.zhao@suse.com>
Signed-off-by: Song Liu <song@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Zheyu Ma [Sun, 10 Apr 2022 07:44:09 +0000 (08:44 +0100)]
media: cx25821: Fix the warning when removing the module
[ Upstream commit
2203436a4d24302871617373a7eb21bc17e38762 ]
When removing the module, we will get the following warning:
[ 14.746697] remove_proc_entry: removing non-empty directory 'irq/21', leaking at least 'cx25821[1]'
[ 14.747449] WARNING: CPU: 4 PID: 368 at fs/proc/generic.c:717 remove_proc_entry+0x389/0x3f0
[ 14.751611] RIP: 0010:remove_proc_entry+0x389/0x3f0
[ 14.759589] Call Trace:
[ 14.759792] <TASK>
[ 14.759975] unregister_irq_proc+0x14c/0x170
[ 14.760340] irq_free_descs+0x94/0xe0
[ 14.760640] mp_unmap_irq+0xb6/0x100
[ 14.760937] acpi_unregister_gsi_ioapic+0x27/0x40
[ 14.761334] acpi_pci_irq_disable+0x1d3/0x320
[ 14.761688] pci_disable_device+0x1ad/0x380
[ 14.762027] ? _raw_spin_unlock_irqrestore+0x2d/0x60
[ 14.762442] ? cx25821_shutdown+0x20/0x9f0 [cx25821]
[ 14.762848] cx25821_finidev+0x48/0xc0 [cx25821]
[ 14.763242] pci_device_remove+0x92/0x240
Fix this by freeing the irq before call pci_disable_device().
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Zheyu Ma [Sun, 10 Apr 2022 07:34:41 +0000 (08:34 +0100)]
media: pci: cx23885: Fix the error handling in cx23885_initdev()
[ Upstream commit
e8123311cf06d7dae71e8c5fe78e0510d20cd30b ]
When the driver fails to call the dma_set_mask(), the driver will get
the following splat:
[ 55.853884] BUG: KASAN: use-after-free in __process_removed_driver+0x3c/0x240
[ 55.854486] Read of size 8 at addr
ffff88810de60408 by task modprobe/590
[ 55.856822] Call Trace:
[ 55.860327] __process_removed_driver+0x3c/0x240
[ 55.861347] bus_for_each_dev+0x102/0x160
[ 55.861681] i2c_del_driver+0x2f/0x50
This is because the driver has initialized the i2c related resources
in cx23885_dev_setup() but not released them in error handling, fix this
bug by modifying the error path that jumps after failing to call the
dma_set_mask().
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Luca Weiss [Fri, 14 Jan 2022 11:02:26 +0000 (11:02 +0000)]
media: venus: hfi: avoid null dereference in deinit
[ Upstream commit
86594f6af867b5165d2ba7b5a71fae3a5961e56c ]
If venus_probe fails at pm_runtime_put_sync the error handling first
calls hfi_destroy and afterwards hfi_core_deinit. As hfi_destroy sets
core->ops to NULL, hfi_core_deinit cannot call the core_deinit function
anymore.
Avoid this null pointer derefence by skipping the call when necessary.
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Thibaut VARÈNE [Sun, 17 Apr 2022 14:51:45 +0000 (16:51 +0200)]
ath9k: fix QCA9561 PA bias level
[ Upstream commit
e999a5da28a0e0f7de242d841ef7d5e48f4646ae ]
This patch fixes an invalid TX PA DC bias level on QCA9561, which
results in a very low output power and very low throughput as devices
are further away from the AP (compared to other 2.4GHz APs).
This patch was suggested by Felix Fietkau, who noted[1]:
"The value written to that register is wrong, because while the mask
definition AR_CH0_TOP2_XPABIASLVL uses a different value for 9561, the
shift definition AR_CH0_TOP2_XPABIASLVL_S is hardcoded to 12, which is
wrong for 9561."
In real life testing, without this patch the 2.4GHz throughput on
Yuncore XD3200 is around 10Mbps sitting next to the AP, and closer to
practical maximum with the patch applied.
[1] https://lore.kernel.org/all/
91c58969-c60e-2f41-00ac-
737786d435ae@nbd.name
Signed-off-by: Thibaut VARÈNE <hacks+kernel@slashdirt.org>
Acked-by: Felix Fietkau <nbd@nbd.name>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220417145145.1847-1-hacks+kernel@slashdirt.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
Kuninori Morimoto [Thu, 21 Apr 2022 02:55:58 +0000 (02:55 +0000)]
ASoC: rsnd: care return value from rsnd_node_fixed_index()
[ Upstream commit
d09a7db431c65aaa8303eb456439d1831ca2e6b4 ]
Renesas Sound is very complex, and thus it needs to use
rsnd_node_fixed_index() to know enabled pin index.
It returns error if strange pin was selected,
but some codes didn't check it.
This patch 1) indicates error message, 2) check return
value.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87pmlbgn5t.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Kuninori Morimoto [Thu, 21 Apr 2022 02:55:27 +0000 (02:55 +0000)]
ASoC: rsnd: care default case on rsnd_ssiu_busif_err_status_clear()
[ Upstream commit
b1384d4c95088d01f4266237faabf165d3d605fc ]
commit
cfb7b8bf1e2d66 ("ASoC: rsnd: tidyup
rsnd_ssiu_busif_err_status_clear()") merged duplicate code, but it didn't
care about default case, and causes smatch warnings.
smatch warnings:
sound/soc/sh/rcar/ssiu.c:112 rsnd_ssiu_busif_err_status_clear() \
error: uninitialized symbol 'offset'.
sound/soc/sh/rcar/ssiu.c:114 rsnd_ssiu_busif_err_status_clear() \
error: uninitialized symbol 'shift'.
This patch cares it.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87r15rgn6p.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Keita Suzuki [Tue, 19 Apr 2022 10:37:19 +0000 (10:37 +0000)]
drm/amd/pm: fix double free in si_parse_power_table()
[ Upstream commit
f3fa2becf2fc25b6ac7cf8d8b1a2e4a86b3b72bd ]
In function si_parse_power_table(), array adev->pm.dpm.ps and its member
is allocated. If the allocation of each member fails, the array itself
is freed and returned with an error code. However, the array is later
freed again in si_dpm_fini() function which is called when the function
returns an error.
This leads to potential double free of the array adev->pm.dpm.ps, as
well as leak of its array members, since the members are not freed in
the allocation function and the array is not nulled when freed.
In addition adev->pm.dpm.num_ps, which keeps track of the allocated
array member, is not updated until the member allocation is
successfully finished, this could also lead to either use after free,
or uninitialized variable access in si_dpm_fini().
Fix this by postponing the free of the array until si_dpm_fini() and
increment adev->pm.dpm.num_ps everytime the array member is allocated.
Signed-off-by: Keita Suzuki <keitasuzuki.park@sslab.ics.keio.ac.jp>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Ulf Hansson [Fri, 1 Apr 2022 14:11:24 +0000 (16:11 +0200)]
cpuidle: PSCI: Improve support for suspend-to-RAM for PSCI OSI mode
[ Upstream commit
171b66e2e2e9d80b93c8cff799e6175074b22297 ]
When PSCI OSI mode is supported the syscore flag is set for the CPU devices
that becomes attached to their PM domains (genpds). In the suspend-to-idle
case, we call dev_pm_genpd_suspend|resume() to allow genpd to properly
manage the power-off/on operations (pick an idlestate and manage the on/off
notifications).
For suspend-to-ram, dev_pm_genpd_suspend|resume() is currently not being
called, which causes a problem that the genpd on/off notifiers do not get
sent as expected. This prevents the platform-specific operations from being
executed, typically needed just before/after the boot CPU is being turned
off/on.
To deal with this problem, let's register a syscore ops for cpuidle-psci
when PSCI OSI mode is being used and call dev_pm_genpd_suspend|resume()
from them. In this way, genpd regains control of the PM domain topology and
then sends the on/off notifications when it's appropriate.
Reported-by: Maulik Shah <quic_mkshah@quicinc.com>
Suggested-by: Maulik Shah <quic_mkshah@quicinc.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Maulik Shah <quic_mkshah@quicinc.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
James Smart [Tue, 12 Apr 2022 22:19:57 +0000 (15:19 -0700)]
scsi: lpfc: Fix call trace observed during I/O with CMF enabled
[ Upstream commit
d6d45f67a11136cb88a70a29ab22ea6db8ae6bd5 ]
The following was seen with CMF enabled:
BUG: using smp_processor_id() in preemptible
code: systemd-udevd/31711
kernel: caller is lpfc_update_cmf_cmd+0x214/0x420 [lpfc]
kernel: CPU: 12 PID: 31711 Comm: systemd-udevd
kernel: Call Trace:
kernel: <TASK>
kernel: dump_stack_lvl+0x44/0x57
kernel: check_preemption_disabled+0xbf/0xe0
kernel: lpfc_update_cmf_cmd+0x214/0x420 [lpfc]
kernel: lpfc_nvme_fcp_io_submit+0x23b4/0x4df0 [lpfc]
this_cpu_ptr() calls smp_processor_id() in a preemptible context.
Fix by using per_cpu_ptr() with raw_smp_processor_id() instead.
Link: https://lore.kernel.org/r/20220412222008.126521-16-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
James Smart [Tue, 12 Apr 2022 22:19:48 +0000 (15:19 -0700)]
scsi: lpfc: Fix SCSI I/O completion and abort handler deadlock
[ Upstream commit
03cbbd7c2f5ee288f648f4aeedc765a181188553 ]
During stress I/O tests with 500+ vports, hard LOCKUP call traces are
observed.
CPU A:
native_queued_spin_lock_slowpath+0x192
_raw_spin_lock_irqsave+0x32
lpfc_handle_fcp_err+0x4c6
lpfc_fcp_io_cmd_wqe_cmpl+0x964
lpfc_sli4_fp_handle_cqe+0x266
__lpfc_sli4_process_cq+0x105
__lpfc_sli4_hba_process_cq+0x3c
lpfc_cq_poll_hdler+0x16
irq_poll_softirq+0x76
__softirqentry_text_start+0xe4
irq_exit+0xf7
do_IRQ+0x7f
CPU B:
native_queued_spin_lock_slowpath+0x5b
_raw_spin_lock+0x1c
lpfc_abort_handler+0x13e
scmd_eh_abort_handler+0x85
process_one_work+0x1a7
worker_thread+0x30
kthread+0x112
ret_from_fork+0x1f
Diagram of lockup:
CPUA CPUB
---- ----
lpfc_cmd->buf_lock
phba->hbalock
lpfc_cmd->buf_lock
phba->hbalock
Fix by reordering the taking of the lpfc_cmd->buf_lock and phba->hbalock in
lpfc_abort_handler routine so that it tries to take the lpfc_cmd->buf_lock
first before phba->hbalock.
Link: https://lore.kernel.org/r/20220412222008.126521-7-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
James Smart [Tue, 12 Apr 2022 22:19:44 +0000 (15:19 -0700)]
scsi: lpfc: Move cfg_log_verbose check before calling lpfc_dmp_dbg()
[ Upstream commit
e294647b1aed4247fe52851f3a3b2b19ae906228 ]
In an attempt to log message 0126 with LOG_TRACE_EVENT, the following hard
lockup call trace hangs the system.
Call Trace:
_raw_spin_lock_irqsave+0x32/0x40
lpfc_dmp_dbg.part.32+0x28/0x220 [lpfc]
lpfc_cmpl_els_fdisc+0x145/0x460 [lpfc]
lpfc_sli_cancel_jobs+0x92/0xd0 [lpfc]
lpfc_els_flush_cmd+0x43c/0x670 [lpfc]
lpfc_els_flush_all_cmd+0x37/0x60 [lpfc]
lpfc_sli4_async_event_proc+0x956/0x1720 [lpfc]
lpfc_do_work+0x1485/0x1d70 [lpfc]
kthread+0x112/0x130
ret_from_fork+0x1f/0x40
Kernel panic - not syncing: Hard LOCKUP
The same CPU tries to claim the phba->port_list_lock twice.
Move the cfg_log_verbose checks as part of the lpfc_printf_vlog() and
lpfc_printf_log() macros before calling lpfc_dmp_dbg(). There is no need
to take the phba->port_list_lock within lpfc_dmp_dbg().
Link: https://lore.kernel.org/r/20220412222008.126521-3-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Len Brown [Fri, 11 Feb 2022 02:06:56 +0000 (21:06 -0500)]
tools/power turbostat: fix ICX DRAM power numbers
[ Upstream commit
6397b6418935773a34b533b3348b03f4ce3d7050 ]
ICX (and its duplicates) require special hard-coded DRAM RAPL units,
rather than using the generic RAPL energy units.
Reported-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Biju Das [Mon, 11 Apr 2022 17:31:15 +0000 (18:31 +0100)]
spi: spi-rspi: Remove setting {src,dst}_{addr,addr_width} based on DMA direction
[ Upstream commit
6f381481a5b236cb53d6de2c49c6ef83a4d0f432 ]
The direction field in the DMA config is deprecated. The rspi driver
sets {src,dst}_{addr,addr_width} based on the DMA direction and
it results in dmaengine_slave_config() failure as RZ DMAC driver
validates {src,dst}_addr_width values independent of DMA direction.
This patch fixes the issue by passing both {src,dst}_{addr,addr_width}
values independent of DMA direction.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Suggested-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20220411173115.6619-1-biju.das.jz@bp.renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Po-Hao Huang [Thu, 7 Apr 2022 09:58:58 +0000 (17:58 +0800)]
rtw88: 8821c: fix debugfs rssi value
[ Upstream commit
ece31c93d4d68f7eb8eea4431b052aacdb678de2 ]
RSSI value per frame is reported to mac80211 but not maintained in
our own statistics, add it back to help us debug.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220407095858.46807-7-pkshih@realtek.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
Amadeusz Sławiński [Tue, 12 Apr 2022 09:16:28 +0000 (11:16 +0200)]
ALSA: jack: Access input_dev under mutex
[ Upstream commit
1b6a6fc5280e97559287b61eade2d4b363e836f2 ]
It is possible when using ASoC that input_dev is unregistered while
calling snd_jack_report, which causes NULL pointer dereference.
In order to prevent this serialize access to input_dev using mutex lock.
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20220412091628.3056922-1-amadeuszx.slawinski@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Haowen Bai [Mon, 11 Apr 2022 01:32:37 +0000 (09:32 +0800)]
sfc: ef10: Fix assigning negative value to unsigned variable
[ Upstream commit
b8ff3395fbdf3b79a99d0ef410fc34c51044121e ]
fix warning reported by smatch:
251 drivers/net/ethernet/sfc/ef10.c:2259 efx_ef10_tx_tso_desc()
warn: assigning (-208) to unsigned variable 'ip_tot_len'
Signed-off-by: Haowen Bai <baihaowen@meizu.com>
Acked-by: Edward Cree <ecree.xilinx@gmail.com>
Link: https://lore.kernel.org/r/1649640757-30041-1-git-send-email-baihaowen@meizu.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Paul E. McKenney [Thu, 17 Mar 2022 16:30:10 +0000 (09:30 -0700)]
rcu: Make TASKS_RUDE_RCU select IRQ_WORK
[ Upstream commit
46e861be589881e0905b9ade3d8439883858721c ]
The TASKS_RUDE_RCU does not select IRQ_WORK, which can result in build
failures for kernels that do not otherwise select IRQ_WORK. This commit
therefore causes the TASKS_RUDE_RCU Kconfig option to select IRQ_WORK.
Reported-by: Hyeonggon Yoo <42.hyeyoo@gmail.com>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Padmanabha Srinivasaiah [Thu, 17 Feb 2022 15:25:19 +0000 (16:25 +0100)]
rcu-tasks: Fix race in schedule and flush work
[ Upstream commit
f75fd4b9221d93177c50dcfde671b2e907f53e86 ]
While booting secondary CPUs, cpus_read_[lock/unlock] is not keeping
online cpumask stable. The transient online mask results in below
calltrace.
[ 0.324121] CPU1: Booted secondary processor 0x0000000001 [0x410fd083]
[ 0.346652] Detected PIPT I-cache on CPU2
[ 0.347212] CPU2: Booted secondary processor 0x0000000002 [0x410fd083]
[ 0.377255] Detected PIPT I-cache on CPU3
[ 0.377823] CPU3: Booted secondary processor 0x0000000003 [0x410fd083]
[ 0.379040] ------------[ cut here ]------------
[ 0.383662] WARNING: CPU: 0 PID: 10 at kernel/workqueue.c:3084 __flush_work+0x12c/0x138
[ 0.384850] Modules linked in:
[ 0.385403] CPU: 0 PID: 10 Comm: rcu_tasks_rude_ Not tainted 5.17.0-rc3-v8+ #13
[ 0.386473] Hardware name: Raspberry Pi 4 Model B Rev 1.4 (DT)
[ 0.387289] pstate:
20000005 (nzCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[ 0.388308] pc : __flush_work+0x12c/0x138
[ 0.388970] lr : __flush_work+0x80/0x138
[ 0.389620] sp :
ffffffc00aaf3c60
[ 0.390139] x29:
ffffffc00aaf3d20 x28:
ffffffc009c16af0 x27:
ffffff80f761df48
[ 0.391316] x26:
0000000000000004 x25:
0000000000000003 x24:
0000000000000100
[ 0.392493] x23:
ffffffffffffffff x22:
ffffffc009c16b10 x21:
ffffffc009c16b28
[ 0.393668] x20:
ffffffc009e53861 x19:
ffffff80f77fbf40 x18:
00000000d744fcc9
[ 0.394842] x17:
000000000000000b x16:
00000000000001c2 x15:
ffffffc009e57550
[ 0.396016] x14:
0000000000000000 x13:
ffffffffffffffff x12:
0000000100000000
[ 0.397190] x11:
0000000000000462 x10:
ffffff8040258008 x9 :
0000000100000000
[ 0.398364] x8 :
0000000000000000 x7 :
ffffffc0093c8bf4 x6 :
0000000000000000
[ 0.399538] x5 :
0000000000000000 x4 :
ffffffc00a976e40 x3 :
ffffffc00810444c
[ 0.400711] x2 :
0000000000000004 x1 :
0000000000000000 x0 :
0000000000000000
[ 0.401886] Call trace:
[ 0.402309] __flush_work+0x12c/0x138
[ 0.402941] schedule_on_each_cpu+0x228/0x278
[ 0.403693] rcu_tasks_rude_wait_gp+0x130/0x144
[ 0.404502] rcu_tasks_kthread+0x220/0x254
[ 0.405264] kthread+0x174/0x1ac
[ 0.405837] ret_from_fork+0x10/0x20
[ 0.406456] irq event stamp: 102
[ 0.406966] hardirqs last enabled at (101): [<
ffffffc0093c8468>] _raw_spin_unlock_irq+0x78/0xb4
[ 0.408304] hardirqs last disabled at (102): [<
ffffffc0093b8270>] el1_dbg+0x24/0x5c
[ 0.409410] softirqs last enabled at (54): [<
ffffffc0081b80c8>] local_bh_enable+0xc/0x2c
[ 0.410645] softirqs last disabled at (50): [<
ffffffc0081b809c>] local_bh_disable+0xc/0x2c
[ 0.411890] ---[ end trace
0000000000000000 ]---
[ 0.413000] smp: Brought up 1 node, 4 CPUs
[ 0.413762] SMP: Total of 4 processors activated.
[ 0.414566] CPU features: detected: 32-bit EL0 Support
[ 0.415414] CPU features: detected: 32-bit EL1 Support
[ 0.416278] CPU features: detected: CRC32 instructions
[ 0.447021] Callback from call_rcu_tasks_rude() invoked.
[ 0.506693] Callback from call_rcu_tasks() invoked.
This commit therefore fixes this issue by applying a single-CPU
optimization to the RCU Tasks Rude grace-period process. The key point
here is that the purpose of this RCU flavor is to force a schedule on
each online CPU since some past event. But the rcu_tasks_rude_wait_gp()
function runs in the context of the RCU Tasks Rude's grace-period kthread,
so there must already have been a context switch on the current CPU since
the call to either synchronize_rcu_tasks_rude() or call_rcu_tasks_rude().
So if there is only a single CPU online, RCU Tasks Rude's grace-period
kthread does not need to anything at all.
It turns out that the rcu_tasks_rude_wait_gp() function's call to
schedule_on_each_cpu() causes problems during early boot. During that
time, there is only one online CPU, namely the boot CPU. Therefore,
applying this single-CPU optimization fixes early-boot instances of
this problem.
Link: https://lore.kernel.org/lkml/20220210184319.25009-1-treasure4paddy@gmail.com/T/
Suggested-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Padmanabha Srinivasaiah <treasure4paddy@gmail.com>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Saaem Rizvi [Mon, 28 Mar 2022 18:25:16 +0000 (14:25 -0400)]
drm/amd/display: Disabling Z10 on DCN31
[ Upstream commit
5d5af34072c8b11f60960c3bea57ff9de5877791 ]
[WHY]
Z10 is should not be enabled by default on DCN31.
[HOW]
Using DC debug flags to disable Z10 by default on DCN31.
Reviewed-by: Eric Yang <Eric.Yang2@amd.com>
Acked-by: Pavle Kotarac <Pavle.Kotarac@amd.com>
Signed-off-by: Saaem Rizvi <syerizvi@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Liviu Dudau [Thu, 2 Dec 2021 17:00:33 +0000 (17:00 +0000)]
drm/komeda: return early if drm_universal_plane_init() fails.
[ Upstream commit
c8f76c37cc3668ee45e081e76a15f24a352ebbdd ]
If drm_universal_plane_init() fails early we jump to the common cleanup code
that calls komeda_plane_destroy() which in turn could access the uninitalised
drm_plane and crash. Return early if an error is detected without going through
the common code.
Reported-by: Steven Price <steven.price@arm.com>
Reviewed-by: Steven Price <steven.price@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Link: https://lore.kernel.org/dri-devel/20211203100946.2706922-1-liviu.dudau@arm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
Peter Seiderer [Mon, 4 Apr 2022 16:54:14 +0000 (18:54 +0200)]
mac80211: minstrel_ht: fix where rate stats are stored (fixes debugfs output)
[ Upstream commit
5c6dd7bd569b54c0d2904125d7366aa93f077f67 ]
Using an ath9k card the debugfs output of minstrel_ht looks like the following
(note the zero values for the first four rates sum-of success/attempts):
best ____________rate__________ ____statistics___ _____last____ ______sum-of________
mode guard # rate [name idx airtime max_tp] [avg(tp) avg(prob)] [retry|suc|att] [#success | #attempts]
OFDM 1 DP 6.0M 272 1640 5.2 3.1 53.8 3 0 0 0 0
OFDM 1 C 9.0M 273 1104 7.7 4.6 53.8 4 0 0 0 0
OFDM 1 B 12.0M 274 836 10.0 6.0 53.8 4 0 0 0 0
OFDM 1 A S 18.0M 275 568 14.3 8.5 53.8 5 0 0 0 0
OFDM 1 S 24.0M 276 436 18.1 0.0 0.0 5 0 1 80 1778
OFDM 1 36.0M 277 300 24.9 0.0 0.0 0 0 1 0 107
OFDM 1 S 48.0M 278 236 30.4 0.0 0.0 0 0 0 0 75
OFDM 1 54.0M 279 212 33.0 0.0 0.0 0 0 0 0 72
Total packet count:: ideal 16582 lookaround 885
Average # of aggregated frames per A-MPDU: 1.0
Debugging showed that the rate statistics for the first four rates where
stored in the MINSTREL_CCK_GROUP instead of the MINSTREL_OFDM_GROUP because
in minstrel_ht_get_stats() the supported check was not honoured as done in
various other places, e.g net/mac80211/rc80211_minstrel_ht_debugfs.c:
74 if (!(mi->supported[i] & BIT(j)))
75 continue;
With the patch applied the output looks good:
best ____________rate__________ ____statistics___ _____last____ ______sum-of________
mode guard # rate [name idx airtime max_tp] [avg(tp) avg(prob)] [retry|suc|att] [#success | #attempts]
OFDM 1 D 6.0M 272 1640 5.2 5.2 100.0 3 0 0 1 1
OFDM 1 C 9.0M 273 1104 7.7 7.7 100.0 4 0 0 38 38
OFDM 1 B 12.0M 274 836 10.0 9.9 89.5 4 2 2 372 395
OFDM 1 A P 18.0M 275 568 14.3 14.3 97.2 5 52 53 6956 7181
OFDM 1 S 24.0M 276 436 18.1 0.0 0.0 0 0 1 6 163
OFDM 1 36.0M 277 300 24.9 0.0 0.0 0 0 1 0 35
OFDM 1 S 48.0M 278 236 30.4 0.0 0.0 0 0 0 0 38
OFDM 1 S 54.0M 279 212 33.0 0.0 0.0 0 0 0 0 38
Total packet count:: ideal 7097 lookaround 287
Average # of aggregated frames per A-MPDU: 1.0
Signed-off-by: Peter Seiderer <ps.report@gmx.net>
Link: https://lore.kernel.org/r/20220404165414.1036-1-ps.report@gmx.net
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Kirill A. Shutemov [Tue, 5 Apr 2022 23:29:38 +0000 (02:29 +0300)]
ACPICA: Avoid cache flush inside virtual machines
[ Upstream commit
e2efb6359e620521d1e13f69b2257de8ceaa9475 ]
While running inside virtual machine, the kernel can bypass cache
flushing. Changing sleep state in a virtual machine doesn't affect the
host system sleep state and cannot lead to data loss.
Before entering sleep states, the ACPI code flushes caches to prevent
data loss using the WBINVD instruction. This mechanism is required on
bare metal.
But, any use WBINVD inside of a guest is worthless. Changing sleep
state in a virtual machine doesn't affect the host system sleep state
and cannot lead to data loss, so most hypervisors simply ignore it.
Despite this, the ACPI code calls WBINVD unconditionally anyway.
It's useless, but also normally harmless.
In TDX guests, though, WBINVD stops being harmless; it triggers a
virtualization exception (#VE). If the ACPI cache-flushing WBINVD
were left in place, TDX guests would need handling to recover from
the exception.
Avoid using WBINVD whenever running under a hypervisor. This both
removes the useless WBINVDs and saves TDX from implementing WBINVD
handling.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20220405232939.73860-30-kirill.shutemov@linux.intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
Mike Travis [Wed, 6 Apr 2022 19:51:48 +0000 (14:51 -0500)]
x86/platform/uv: Update TSC sync state for UV5
[ Upstream commit
bb3ab81bdbd53f88f26ffabc9fb15bd8466486ec ]
The UV5 platform synchronizes the TSCs among all chassis, and will not
proceed to OS boot without achieving synchronization. Previous UV
platforms provided a register indicating successful synchronization.
This is no longer available on UV5. On this platform TSC_ADJUST
should not be reset by the kernel.
Signed-off-by: Mike Travis <mike.travis@hpe.com>
Signed-off-by: Steve Wahl <steve.wahl@hpe.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Dimitri Sivanich <dimitri.sivanich@hpe.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20220406195149.228164-3-steve.wahl@hpe.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
Daniel Vetter [Tue, 5 Apr 2022 21:03:31 +0000 (23:03 +0200)]
fbcon: Consistently protect deferred_takeover with console_lock()
[ Upstream commit
43553559121ca90965b572cf8a1d6d0fd618b449 ]
This shouldn't be a problem in practice since until we've actually
taken over the console there's nothing we've registered with the
console/vt subsystem, so the exit/unbind path that check this can't
do the wrong thing. But it's confusing, so fix it by moving it a tad
later.
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Du Cheng <ducheng2@gmail.com>
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: Claudio Suarez <cssk@net-c.es>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220405210335.3434130-14-daniel.vetter@ffwll.ch
Signed-off-by: Sasha Levin <sashal@kernel.org>
Niels Dossche [Sun, 3 Apr 2022 23:15:24 +0000 (01:15 +0200)]
ipv6: fix locking issues with loops over idev->addr_list
[ Upstream commit
51454ea42c1ab4e0c2828bb0d4d53957976980de ]
idev->addr_list needs to be protected by idev->lock. However, it is not
always possible to do so while iterating and performing actions on
inet6_ifaddr instances. For example, multiple functions (like
addrconf_{join,leave}_anycast) eventually call down to other functions
that acquire the idev->lock. The current code temporarily unlocked the
idev->lock during the loops, which can cause race conditions. Moving the
locks up is also not an appropriate solution as the ordering of lock
acquisition will be inconsistent with for example mc_lock.
This solution adds an additional field to inet6_ifaddr that is used
to temporarily add the instances to a temporary list while holding
idev->lock. The temporary list can then be traversed without holding
idev->lock. This change was done in two places. In addrconf_ifdown, the
list_for_each_entry_safe variant of the list loop is also no longer
necessary as there is no deletion within that specific loop.
Suggested-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Niels Dossche <dossche.niels@gmail.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/r/20220403231523.45843-1-dossche.niels@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Haowen Bai [Fri, 1 Apr 2022 07:10:54 +0000 (15:10 +0800)]
ipw2x00: Fix potential NULL dereference in libipw_xmit()
[ Upstream commit
e8366bbabe1d207cf7c5b11ae50e223ae6fc278b ]
crypt and crypt->ops could be null, so we need to checking null
before dereference
Signed-off-by: Haowen Bai <baihaowen@meizu.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/1648797055-25730-1-git-send-email-baihaowen@meizu.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
Haowen Bai [Fri, 25 Mar 2022 10:15:15 +0000 (18:15 +0800)]
b43: Fix assigning negative value to unsigned variable
[ Upstream commit
11800d893b38e0e12d636c170c1abc19c43c730c ]
fix warning reported by smatch:
drivers/net/wireless/broadcom/b43/phy_n.c:585 b43_nphy_adjust_lna_gain_table()
warn: assigning (-2) to unsigned variable '*(lna_gain[0])'
Signed-off-by: Haowen Bai <baihaowen@meizu.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/1648203315-28093-1-git-send-email-baihaowen@meizu.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
Haowen Bai [Fri, 25 Mar 2022 10:17:13 +0000 (18:17 +0800)]
b43legacy: Fix assigning negative value to unsigned variable
[ Upstream commit
3f6b867559b3d43a7ce1b4799b755e812fc0d503 ]
fix warning reported by smatch:
drivers/net/wireless/broadcom/b43legacy/phy.c:1181 b43legacy_phy_lo_b_measure()
warn: assigning (-772) to unsigned variable 'fval'
Signed-off-by: Haowen Bai <baihaowen@meizu.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/1648203433-8736-1-git-send-email-baihaowen@meizu.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
Niels Dossche [Mon, 21 Mar 2022 22:55:16 +0000 (23:55 +0100)]
mwifiex: add mutex lock for call in mwifiex_dfs_chan_sw_work_queue
[ Upstream commit
3e12968f6d12a34b540c39cbd696a760cc4616f0 ]
cfg80211_ch_switch_notify uses ASSERT_WDEV_LOCK to assert that
net_device->ieee80211_ptr->mtx (which is the same as priv->wdev.mtx)
is held during the function's execution.
mwifiex_dfs_chan_sw_work_queue is one of its callers, which does not
hold that lock, therefore violating the assertion.
Add a lock around the call.
Disclaimer:
I am currently working on a static analyser to detect missing locks.
This was a reported case. I manually verified the report by looking
at the code, so that I do not send wrong information or patches.
After concluding that this seems to be a true positive, I created
this patch.
However, as I do not in fact have this particular hardware,
I was unable to test it.
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Niels Dossche <dossche.niels@gmail.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220321225515.32113-1-dossche.niels@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
Quentin Monnet [Mon, 4 Apr 2022 14:09:44 +0000 (15:09 +0100)]
selftests/bpf: Fix parsing of prog types in UAPI hdr for bpftool sync
[ Upstream commit
4eeebce6ac4ad80ee8243bb847c98e0e55848d47 ]
The script for checking that various lists of types in bpftool remain in
sync with the UAPI BPF header uses a regex to parse enum bpf_prog_type.
If this enum contains a set of values different from the list of program
types in bpftool, it complains.
This script should have reported the addition, some time ago, of the new
BPF_PROG_TYPE_SYSCALL, which was not reported to bpftool's program types
list. It failed to do so, because it failed to parse that new type from
the enum. This is because the new value, in the BPF header, has an
explicative comment on the same line, and the regex does not support
that.
Let's update the script to support parsing enum values when they have
comments on the same line.
Signed-off-by: Quentin Monnet <quentin@isovalent.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20220404140944.64744-1-quentin@isovalent.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
Nikolay Borisov [Thu, 31 Mar 2022 14:09:49 +0000 (17:09 +0300)]
selftests/bpf: Fix vfs_link kprobe definition
[ Upstream commit
e299bcd4d16ff86f46c48df1062c8aae0eca1ed8 ]
Since commit
6521f8917082 ("namei: prepare for idmapped mounts")
vfs_link's prototype was changed, the kprobe definition in
profiler selftest in turn wasn't updated. The result is that all
argument after the first are now stored in different registers. This
means that self-test has been broken ever since. Fix it by updating the
kprobe definition accordingly.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20220331140949.1410056-1-nborisov@suse.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
Liu Zixian [Tue, 22 Mar 2022 09:17:30 +0000 (17:17 +0800)]
drm/virtio: fix NULL pointer dereference in virtio_gpu_conn_get_modes
[ Upstream commit
194d250cdc4a40ccbd179afd522a9e9846957402 ]
drm_cvt_mode may return NULL and we should check it.
This bug is found by syzkaller:
FAULT_INJECTION stacktrace:
[ 168.567394] FAULT_INJECTION: forcing a failure.
name failslab, interval 1, probability 0, space 0, times 1
[ 168.567403] CPU: 1 PID: 6425 Comm: syz Kdump: loaded Not tainted 4.19.90-vhulk2201.1.0.h1035.kasan.eulerosv2r10.aarch64 #1
[ 168.567406] Hardware name: QEMU KVM Virtual Machine, BIOS 0.0.0 02/06/2015
[ 168.567408] Call trace:
[ 168.567414] dump_backtrace+0x0/0x310
[ 168.567418] show_stack+0x28/0x38
[ 168.567423] dump_stack+0xec/0x15c
[ 168.567427] should_fail+0x3ac/0x3d0
[ 168.567437] __should_failslab+0xb8/0x120
[ 168.567441] should_failslab+0x28/0xc0
[ 168.567445] kmem_cache_alloc_trace+0x50/0x640
[ 168.567454] drm_mode_create+0x40/0x90
[ 168.567458] drm_cvt_mode+0x48/0xc78
[ 168.567477] virtio_gpu_conn_get_modes+0xa8/0x140 [virtio_gpu]
[ 168.567485] drm_helper_probe_single_connector_modes+0x3a4/0xd80
[ 168.567492] drm_mode_getconnector+0x2e0/0xa70
[ 168.567496] drm_ioctl_kernel+0x11c/0x1d8
[ 168.567514] drm_ioctl+0x558/0x6d0
[ 168.567522] do_vfs_ioctl+0x160/0xf30
[ 168.567525] ksys_ioctl+0x98/0xd8
[ 168.567530] __arm64_sys_ioctl+0x50/0xc8
[ 168.567536] el0_svc_common+0xc8/0x320
[ 168.567540] el0_svc_handler+0xf8/0x160
[ 168.567544] el0_svc+0x10/0x218
KASAN stacktrace:
[ 168.567561] BUG: KASAN: null-ptr-deref in virtio_gpu_conn_get_modes+0xb4/0x140 [virtio_gpu]
[ 168.567565] Read of size 4 at addr
0000000000000054 by task syz/6425
[ 168.567566]
[ 168.567571] CPU: 1 PID: 6425 Comm: syz Kdump: loaded Not tainted 4.19.90-vhulk2201.1.0.h1035.kasan.eulerosv2r10.aarch64 #1
[ 168.567573] Hardware name: QEMU KVM Virtual Machine, BIOS 0.0.0 02/06/2015
[ 168.567575] Call trace:
[ 168.567578] dump_backtrace+0x0/0x310
[ 168.567582] show_stack+0x28/0x38
[ 168.567586] dump_stack+0xec/0x15c
[ 168.567591] kasan_report+0x244/0x2f0
[ 168.567594] __asan_load4+0x58/0xb0
[ 168.567607] virtio_gpu_conn_get_modes+0xb4/0x140 [virtio_gpu]
[ 168.567612] drm_helper_probe_single_connector_modes+0x3a4/0xd80
[ 168.567617] drm_mode_getconnector+0x2e0/0xa70
[ 168.567621] drm_ioctl_kernel+0x11c/0x1d8
[ 168.567624] drm_ioctl+0x558/0x6d0
[ 168.567628] do_vfs_ioctl+0x160/0xf30
[ 168.567632] ksys_ioctl+0x98/0xd8
[ 168.567636] __arm64_sys_ioctl+0x50/0xc8
[ 168.567641] el0_svc_common+0xc8/0x320
[ 168.567645] el0_svc_handler+0xf8/0x160
[ 168.567649] el0_svc+0x10/0x218
Signed-off-by: Liu Zixian <liuzixian4@huawei.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20220322091730.1653-1-liuzixian4@huawei.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Zack Rusin [Fri, 18 Mar 2022 17:43:30 +0000 (13:43 -0400)]
drm/vmwgfx: validate the screen formats
[ Upstream commit
8bb75aeb58bd688d70827ae179bd3da57b6d975b ]
The kms code wasn't validating the modifiers and was letting through
unsupported formats. rgb8 was never properly supported and has no
matching svga screen target format so remove it.
This fixes format/modifier failures in kms_addfb_basic from IGT.
Signed-off-by: Zack Rusin <zackr@vmware.com>
Reviewed-by: Martin Krastev <krastevm@vmware.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220318174332.440068-4-zack@kde.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
Tejas Upadhyay [Wed, 2 Mar 2022 04:32:56 +0000 (10:02 +0530)]
iommu/vt-d: Add RPLS to quirk list to skip TE disabling
[ Upstream commit
0a967f5bfd9134b89681cae58deb222e20840e76 ]
The VT-d spec requires (10.4.4 Global Command Register, TE
field) that:
Hardware implementations supporting DMA draining must drain
any in-flight DMA read/write requests queued within the
Root-Complex before completing the translation enable
command and reflecting the status of the command through
the TES field in the Global Status register.
Unfortunately, some integrated graphic devices fail to do
so after some kind of power state transition. As the
result, the system might stuck in iommu_disable_translati
on(), waiting for the completion of TE transition.
This adds RPLS to a quirk list for those devices and skips
TE disabling if the qurik hits.
Link: https://gitlab.freedesktop.org/drm/intel/-/issues/4898
Tested-by: Raviteja Goud Talla <ravitejax.goud.talla@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Acked-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Tejas Upadhyay <tejaskumarx.surendrakumar.upadhyay@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220302043256.191529-1-tejaskumarx.surendrakumar.upadhyay@intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
Qu Wenruo [Tue, 12 Apr 2022 12:30:14 +0000 (20:30 +0800)]
btrfs: fix the error handling for submit_extent_page() for btrfs_do_readpage()
commit
10f7f6f879c28f8368d6516ab1ccf3517a1f5d3d upstream.
[BUG]
Test case generic/475 have a very high chance (almost 100%) to hit a fs
hang, where a data page will never be unlocked and hang all later
operations.
[CAUSE]
In btrfs_do_readpage(), if we hit an error from submit_extent_page() we
will try to do the cleanup for our current io range, and exit.
This works fine for PAGE_SIZE == sectorsize cases, but not for subpage.
For subpage btrfs_do_readpage() will lock the full page first, which can
contain several different sectors and extents:
btrfs_do_readpage()
|- begin_page_read()
| |- btrfs_subpage_start_reader();
| Now the page will have PAGE_SIZE / sectorsize reader pending,
| and the page is locked.
|
|- end_page_read() for different branches
| This function will reduce subpage readers, and when readers
| reach 0, it will unlock the page.
But when submit_extent_page() failed, we only cleanup the current
io range, while the remaining io range will never be cleaned up, and the
page remains locked forever.
[FIX]
Update the error handling of submit_extent_page() to cleanup all the
remaining subpage range before exiting the loop.
Please note that, now submit_extent_page() can only fail due to
sanity check in alloc_new_bio().
Thus regular IO errors are impossible to trigger the error path.
CC: stable@vger.kernel.org # 5.15+
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Qu Wenruo [Mon, 28 Feb 2022 07:05:53 +0000 (15:05 +0800)]
btrfs: repair super block num_devices automatically
commit
d201238ccd2f30b9bfcfadaeae0972e3a486a176 upstream.
[BUG]
There is a report that a btrfs has a bad super block num devices.
This makes btrfs to reject the fs completely.
BTRFS error (device sdd3): super_num_devices 3 mismatch with num_devices 2 found here
BTRFS error (device sdd3): failed to read chunk tree: -22
BTRFS error (device sdd3): open_ctree failed
[CAUSE]
During btrfs device removal, chunk tree and super block num devs are
updated in two different transactions:
btrfs_rm_device()
|- btrfs_rm_dev_item(device)
| |- trans = btrfs_start_transaction()
| | Now we got transaction X
| |
| |- btrfs_del_item()
| | Now device item is removed from chunk tree
| |
| |- btrfs_commit_transaction()
| Transaction X got committed, super num devs untouched,
| but device item removed from chunk tree.
| (AKA, super num devs is already incorrect)
|
|- cur_devices->num_devices--;
|- cur_devices->total_devices--;
|- btrfs_set_super_num_devices()
All those operations are not in transaction X, thus it will
only be written back to disk in next transaction.
So after the transaction X in btrfs_rm_dev_item() committed, but before
transaction X+1 (which can be minutes away), a power loss happen, then
we got the super num mismatch.
This has been fixed by commit
bbac58698a55 ("btrfs: remove device item
and update super block in the same transaction").
[FIX]
Make the super_num_devices check less strict, converting it from a hard
error to a warning, and reset the value to a correct one for the current
or next transaction commit.
As the number of device items is the critical information where the
super block num_devices is only a cached value (and also useful for
cross checking), it's safe to automatically update it. Other device
related problems like missing device are handled after that and may
require other means to resolve, like degraded mount. With this fix,
potentially affected filesystems won't fail mount and require the manual
repair by btrfs check.
Reported-by: Luca Béla Palkovics <luca.bela.palkovics@gmail.com>
Link: https://lore.kernel.org/linux-btrfs/CA+8xDSpvdm_U0QLBAnrH=zqDq_cWCOH5TiV46CKmp3igr44okQ@mail.gmail.com/
CC: stable@vger.kernel.org # 4.14+
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Qu Wenruo [Tue, 12 Apr 2022 12:30:15 +0000 (20:30 +0800)]
btrfs: return correct error number for __extent_writepage_io()
commit
44e5801fada6925d2bba1987c7b59cbcc9d0d592 upstream.
[BUG]
If we hit an error from submit_extent_page() inside
__extent_writepage_io(), we could still return 0 to the caller, and
even trigger the warning in btrfs_page_assert_not_dirty().
[CAUSE]
In __extent_writepage_io(), if we hit an error from
submit_extent_page(), we will just clean up the range and continue.
This is completely fine for regular PAGE_SIZE == sectorsize, as we can
only hit one sector in one page, thus after the error we're ensured to
exit and @ret will be saved.
But for subpage case, we may have other dirty subpage range in the page,
and in the next loop, we may succeeded submitting the next range.
In that case, @ret will be overwritten, and we return 0 to the caller,
while we have hit some error.
[FIX]
Introduce @has_error and @saved_ret to record the first error we hit, so
we will never forget what error we hit.
CC: stable@vger.kernel.org # 5.15+
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Qu Wenruo [Tue, 10 May 2022 07:10:18 +0000 (15:10 +0800)]
btrfs: add "0x" prefix for unsupported optional features
commit
d5321a0fa8bc49f11bea0b470800962c17d92d8f upstream.
The following error message lack the "0x" obviously:
cannot mount because of unsupported optional features (4000)
Add the prefix to make it less confusing. This can happen on older
kernels that try to mount a filesystem with newer features so it makes
sense to backport to older trees.
CC: stable@vger.kernel.org # 4.14+
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eric W. Biederman [Fri, 29 Apr 2022 14:23:55 +0000 (09:23 -0500)]
ptrace: Reimplement PTRACE_KILL by always sending SIGKILL
commit
6a2d90ba027adba528509ffa27097cffd3879257 upstream.
The current implementation of PTRACE_KILL is buggy and has been for
many years as it assumes it's target has stopped in ptrace_stop. At a
quick skim it looks like this assumption has existed since ptrace
support was added in linux v1.0.
While PTRACE_KILL has been deprecated we can not remove it as
a quick search with google code search reveals many existing
programs calling it.
When the ptracee is not stopped at ptrace_stop some fields would be
set that are ignored except in ptrace_stop. Making the userspace
visible behavior of PTRACE_KILL a noop in those case.
As the usual rules are not obeyed it is not clear what the
consequences are of calling PTRACE_KILL on a running process.
Presumably userspace does not do this as it achieves nothing.
Replace the implementation of PTRACE_KILL with a simple
send_sig_info(SIGKILL) followed by a return 0. This changes the
observable user space behavior only in that PTRACE_KILL on a process
not stopped in ptrace_stop will also kill it. As that has always
been the intent of the code this seems like a reasonable change.
Cc: stable@vger.kernel.org
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Suggested-by: Al Viro <viro@zeniv.linux.org.uk>
Tested-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Oleg Nesterov <oleg@redhat.com>
Link: https://lkml.kernel.org/r/20220505182645.497868-7-ebiederm@xmission.com
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eric W. Biederman [Tue, 26 Apr 2022 21:45:37 +0000 (16:45 -0500)]
ptrace/xtensa: Replace PT_SINGLESTEP with TIF_SINGLESTEP
commit
4a3d2717d140401df7501a95e454180831a0c5af upstream.
xtensa is the last user of the PT_SINGLESTEP flag. Changing tsk->ptrace in
user_enable_single_step and user_disable_single_step without locking could
potentiallly cause problems.
So use a thread info flag instead of a flag in tsk->ptrace. Use TIF_SINGLESTEP
that xtensa already had defined but unused.
Remove the definitions of PT_SINGLESTEP and PT_BLOCKSTEP as they have no more users.
Cc: stable@vger.kernel.org
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Tested-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Oleg Nesterov <oleg@redhat.com>
Link: https://lkml.kernel.org/r/20220505182645.497868-4-ebiederm@xmission.com
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eric W. Biederman [Tue, 26 Apr 2022 21:30:17 +0000 (16:30 -0500)]
ptrace/um: Replace PT_DTRACE with TIF_SINGLESTEP
commit
c200e4bb44e80b343c09841e7caaaca0aac5e5fa upstream.
User mode linux is the last user of the PT_DTRACE flag. Using the flag to indicate
single stepping is a little confusing and worse changing tsk->ptrace without locking
could potentionally cause problems.
So use a thread info flag with a better name instead of flag in tsk->ptrace.
Remove the definition PT_DTRACE as uml is the last user.
Cc: stable@vger.kernel.org
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Tested-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Oleg Nesterov <oleg@redhat.com>
Link: https://lkml.kernel.org/r/20220505182645.497868-3-ebiederm@xmission.com
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kristen Carlson Accardi [Fri, 20 May 2022 17:42:47 +0000 (10:42 -0700)]
x86/sgx: Set active memcg prior to shmem allocation
commit
0c9782e204d3cc5625b9e8bf4e8625d38dfe0139 upstream.
When the system runs out of enclave memory, SGX can reclaim EPC pages
by swapping to normal RAM. These backing pages are allocated via a
per-enclave shared memory area. Since SGX allows unlimited over
commit on EPC memory, the reclaimer thread can allocate a large
number of backing RAM pages in response to EPC memory pressure.
When the shared memory backing RAM allocation occurs during
the reclaimer thread context, the shared memory is charged to
the root memory control group, and the shmem usage of the enclave
is not properly accounted for, making cgroups ineffective at
limiting the amount of RAM an enclave can consume.
For example, when using a cgroup to launch a set of test
enclaves, the kernel does not properly account for 50% - 75% of
shmem page allocations on average. In the worst case, when
nearly all allocations occur during the reclaimer thread, the
kernel accounts less than a percent of the amount of shmem used
by the enclave's cgroup to the correct cgroup.
SGX stores a list of mm_structs that are associated with
an enclave. Pick one of them during reclaim and charge that
mm's memcg with the shmem allocation. The one that gets picked
is arbitrary, but this list almost always only has one mm. The
cases where there is more than one mm with different memcg's
are not worth considering.
Create a new function - sgx_encl_alloc_backing(). This function
is used whenever a new backing storage page needs to be
allocated. Previously the same function was used for page
allocation as well as retrieving a previously allocated page.
Prior to backing page allocation, if there is a mm_struct associated
with the enclave that is requesting the allocation, it is set
as the active memory control group.
[ dhansen: - fix merge conflict with ELDU fixes
- check against actual ksgxd_tsk, not ->mm ]
Cc: stable@vger.kernel.org
Signed-off-by: Kristen Carlson Accardi <kristen@linux.intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Shakeel Butt <shakeelb@google.com>
Acked-by: Roman Gushchin <roman.gushchin@linux.dev>
Link: https://lkml.kernel.org/r/20220520174248.4918-1-kristen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Baoquan He [Wed, 23 Feb 2022 11:32:24 +0000 (19:32 +0800)]
x86/kexec: fix memory leak of elf header buffer
commit
b3e34a47f98974d0844444c5121aaff123004e57 upstream.
This is reported by kmemleak detector:
unreferenced object 0xffffc900002a9000 (size 4096):
comm "kexec", pid 14950, jiffies
4295110793 (age 373.951s)
hex dump (first 32 bytes):
7f 45 4c 46 02 01 01 00 00 00 00 00 00 00 00 00 .ELF............
04 00 3e 00 01 00 00 00 00 00 00 00 00 00 00 00 ..>.............
backtrace:
[<
0000000016a8ef9f>] __vmalloc_node_range+0x101/0x170
[<
000000002b66b6c0>] __vmalloc_node+0xb4/0x160
[<
00000000ad40107d>] crash_prepare_elf64_headers+0x8e/0xcd0
[<
0000000019afff23>] crash_load_segments+0x260/0x470
[<
0000000019ebe95c>] bzImage64_load+0x814/0xad0
[<
0000000093e16b05>] arch_kexec_kernel_image_load+0x1be/0x2a0
[<
000000009ef2fc88>] kimage_file_alloc_init+0x2ec/0x5a0
[<
0000000038f5a97a>] __do_sys_kexec_file_load+0x28d/0x530
[<
0000000087c19992>] do_syscall_64+0x3b/0x90
[<
0000000066e063a4>] entry_SYSCALL_64_after_hwframe+0x44/0xae
In crash_prepare_elf64_headers(), a buffer is allocated via vmalloc() to
store elf headers. While it's not freed back to system correctly when
kdump kernel is reloaded or unloaded. Then memory leak is caused. Fix it
by introducing x86 specific function arch_kimage_file_post_load_cleanup(),
and freeing the buffer there.
And also remove the incorrect elf header buffer freeing code. Before
calling arch specific kexec_file loading function, the image instance has
been initialized. So 'image->elf_headers' must be NULL. It doesn't make
sense to free the elf header buffer in the place.
Three different people have reported three bugs about the memory leak on
x86_64 inside Redhat.
Link: https://lkml.kernel.org/r/20220223113225.63106-2-bhe@redhat.com
Signed-off-by: Baoquan He <bhe@redhat.com>
Acked-by: Dave Young <dyoung@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kan Liang [Wed, 25 May 2022 13:39:52 +0000 (06:39 -0700)]
perf/x86/intel: Fix event constraints for ICL
commit
86dca369075b3e310c3c0adb0f81e513c562b5e4 upstream.
According to the latest event list, the event encoding 0x55
INST_DECODED.DECODERS and 0x56 UOPS_DECODED.DEC0 are only available on
the first 4 counters. Add them into the event constraints table.
Fixes:
6017608936c1 ("perf/x86/intel: Add Icelake support")
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220525133952.1660658-1-kan.liang@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ammar Faizi [Tue, 29 Mar 2022 10:47:05 +0000 (17:47 +0700)]
x86/MCE/AMD: Fix memory leak when threshold_create_bank() fails
commit
e5f28623ceb103e13fc3d7bd45edf9818b227fd0 upstream.
In mce_threshold_create_device(), if threshold_create_bank() fails, the
previously allocated threshold banks array @bp will be leaked because
the call to mce_threshold_remove_device() will not free it.
This happens because mce_threshold_remove_device() fetches the pointer
through the threshold_banks per-CPU variable but bp is written there
only after the bank creation is successful, and not before, when
threshold_create_bank() fails.
Add a helper which unwinds all the bank creation work previously done
and pass into it the previously allocated threshold banks array for
freeing.
[ bp: Massage. ]
Fixes:
6458de97fc15 ("x86/mce/amd: Straighten CPU hotplug path")
Co-developed-by: Alviro Iskandar Setiawan <alviro.iskandar@gnuweeb.org>
Signed-off-by: Alviro Iskandar Setiawan <alviro.iskandar@gnuweeb.org>
Co-developed-by: Yazen Ghannam <yazen.ghannam@amd.com>
Signed-off-by: Yazen Ghannam <yazen.ghannam@amd.com>
Signed-off-by: Ammar Faizi <ammarfaizi2@gnuweeb.org>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220329104705.65256-3-ammarfaizi2@gnuweeb.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Michael Niewöhner [Tue, 17 May 2022 18:31:30 +0000 (20:31 +0200)]
platform/x86: intel-hid: fix _DSM function index handling
commit
1620c80bba53af8c547bab34a1d3bc58319fe608 upstream.
intel_hid_dsm_fn_mask is a bit mask containing one bit for each function
index. Fix the function index check in intel_hid_evaluate_method
accordingly, which was missed in commit
97ab4516205e ("platform/x86:
intel-hid: fix _DSM function index handling").
Fixes:
97ab4516205e ("platform/x86: intel-hid: fix _DSM function index handling")
Cc: stable@vger.kernel.org
Signed-off-by: Michael Niewöhner <linux@mniewoehner.de>
Link: https://lore.kernel.org/r/66f813f5bcc724a0f6dd5adefe6a9728dbe509e3.camel@mniewoehner.de
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mathias Nyman [Wed, 11 May 2022 22:04:50 +0000 (01:04 +0300)]
xhci: Allow host runtime PM as default for Intel Alder Lake N xHCI
commit
74f55a62c4c354f43a6d75f77dd184c4f57b9a26 upstream.
Alder Lake N TCSS xHCI needs to be runtime suspended whenever possible
to allow the TCSS hardware block to enter D3 and thus save energy
Cc: stable@kernel.org
Suggested-by: Gopal Vamshi Krishna <vamshi.krishna.gopal@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220511220450.85367-10-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ronnie Sahlberg [Tue, 31 May 2022 22:48:38 +0000 (08:48 +1000)]
cifs: when extending a file with falloc we should make files not-sparse
commit
f66f8b94e7f2f4ac9fffe710be231ca8f25c5057 upstream.
as this is the only way to make sure the region is allocated.
Fix the conditional that was wrong and only tried to make already
non-sparse files non-sparse.
Cc: stable@vger.kernel.org
Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ronnie Sahlberg [Tue, 31 May 2022 03:01:17 +0000 (13:01 +1000)]
cifs: fix potential double free during failed mount
commit
8378a51e3f8140f60901fb27208cc7a6e47047b5 upstream.
RHBZ: https://bugzilla.redhat.com/show_bug.cgi?id=2088799
Cc: stable@vger.kernel.org
Signed-off-by: Roberto Bergantinos <rbergant@redhat.com>
Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Konstantin Komarov [Fri, 22 Oct 2021 15:15:36 +0000 (18:15 +0300)]
fs/ntfs3: Restore ntfs_xattr_get_acl and ntfs_xattr_set_acl functions
commit
87e21c99bad763524c953ff4d1a61ee19038ddc2 upstream.
Apparently we need to maintain these functions with
ntfs_get_acl_ex and ntfs_set_acl_ex.
This commit fixes xfstest generic/099
Fixes:
95dd8b2c1ed0 ("fs/ntfs3: Remove unnecessary functions")
Reviewed-by: Kari Argillander <kari.argillander@gmail.com>
Signed-off-by: Konstantin Komarov <almaz.alexandrovich@paragon-software.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Konstantin Komarov [Fri, 22 Oct 2021 15:35:43 +0000 (18:35 +0300)]
fs/ntfs3: Update i_ctime when xattr is added
commit
2d44667c306e7806848a3478820f87343feb5421 upstream.
Ctime wasn't updated after setfacl command.
This commit fixes xfstest generic/307
Fixes:
be71b5cba2e6 ("fs/ntfs3: Add attrib operations")
Signed-off-by: Konstantin Komarov <almaz.alexandrovich@paragon-software.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Christophe JAILLET [Thu, 11 Nov 2021 07:45:44 +0000 (08:45 +0100)]
fs/ntfs3: Fix some memory leaks in an error handling path of 'log_replay()'
commit
e589f9b7078e1c0191613cd736f598e81d2390de upstream.
All error handling paths lead to 'out' where many resources are freed.
Do it as well here instead of a direct return, otherwise 'log', 'ra' and
'log->one_page_buf' (at least) will leak.
Fixes:
b46acd6a6a62 ("fs/ntfs3: Add NTFS journal")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Konstantin Komarov <almaz.alexandrovich@paragon-software.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Konstantin Komarov [Wed, 24 Nov 2021 12:08:19 +0000 (15:08 +0300)]
fs/ntfs3: In function ntfs_set_acl_ex do not change inode->i_mode if called from function ntfs_init_acl
commit
9186d472ee780fabf74424756c4c00545166157e upstream.
ntfs_init_acl sets mode. ntfs_init_acl calls ntfs_set_acl_ex.
ntfs_set_acl_ex must not change this mode.
Fixes xfstest generic/444
Fixes:
be71b5cba2e6 ("fs/ntfs3: Add attrib operations")
Reviewed-by: Joe Perches <joe@perches.com>
Signed-off-by: Konstantin Komarov <almaz.alexandrovich@paragon-software.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Konstantin Komarov [Mon, 25 Oct 2021 15:34:06 +0000 (18:34 +0300)]
fs/ntfs3: Check new size for limits
commit
114346978cf61de02832cc3cc68432a3de70fb38 upstream.
We must check size before trying to allocate.
Size can be set for example by "ulimit -f".
Fixes xfstest generic/228
Fixes:
4342306f0f0d ("fs/ntfs3: Add file operations and implementation")
Reviewed-by: Kari Argillander <kari.argillander@gmail.com>
Signed-off-by: Konstantin Komarov <almaz.alexandrovich@paragon-software.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Konstantin Komarov [Fri, 22 Oct 2021 14:37:52 +0000 (17:37 +0300)]
fs/ntfs3: Keep preallocated only if option prealloc enabled
commit
e95113ed4d428219e3395044e29f5713fc446720 upstream.
If size of file was reduced, we still kept allocated blocks.
This commit makes ntfs3 work as other fs like btrfs.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=214719
Fixes:
4342306f0f0d ("fs/ntfs3: Add file operations and implementation")
Reported-by: Ganapathi Kamath <hgkamath@hotmail.com>
Tested-by: Ganapathi Kamath <hgkamath@hotmail.com>
Reviewed-by: Kari Argillander <kari.argillander@gmail.com>
Signed-off-by: Konstantin Komarov <almaz.alexandrovich@paragon-software.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Konstantin Komarov [Mon, 25 Oct 2021 15:31:28 +0000 (18:31 +0300)]
fs/ntfs3: Fix fiemap + fix shrink file size (to remove preallocated space)
commit
3880f2b816a7e4ca889b7e8a42e6c62c5706ed36 upstream.
Two problems:
1. ntfs3_setattr can't truncate preallocated space;
2. if allocated fragment "cross" valid size, then fragment splits into two parts:
- normal part;
- unwritten part (here we must return FIEMAP_EXTENT_LAST).
Before this commit we returned FIEMAP_EXTENT_LAST for whole fragment.
Fixes xfstest generic/092
Fixes:
4342306f0f0d ("fs/ntfs3: Add file operations and implementation")
Signed-off-by: Konstantin Komarov <almaz.alexandrovich@paragon-software.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Konstantin Komarov [Mon, 25 Oct 2021 15:48:38 +0000 (18:48 +0300)]
fs/ntfs3: Update valid size if -EIOCBQUEUED
commit
52e00ea6b26e45fb8159e3b57cdde8d3f9bdd8e9 upstream.
Update valid size if write is still in I/O queue.
Fixes xfstest generic/240
Fixes:
82cae269cfa9 ("fs/ntfs3: Add initialization of super block")
Signed-off-by: Konstantin Komarov <almaz.alexandrovich@paragon-software.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kishon Vijay Abraham I [Tue, 10 May 2022 09:16:29 +0000 (14:46 +0530)]
usb: core: hcd: Add support for deferring roothub registration
commit
a44623d9279086c89f631201d993aa332f7c9e66 upstream.
It has been observed with certain PCIe USB cards (like Inateck connected
to AM64 EVM or J7200 EVM) that as soon as the primary roothub is
registered, port status change is handled even before xHC is running
leading to cold plug USB devices not detected. For such cases, registering
both the root hubs along with the second HCD is required. Add support for
deferring roothub registration in usb_add_hcd(), so that both primary and
secondary roothubs are registered along with the second HCD.
This patch has been added and reverted earier as it triggered a race
in usb device enumeration.
That race is now fixed in 5.16-rc3, and in stable back to 5.4
commit
6cca13de26ee ("usb: hub: Fix locking issues with address0_mutex")
commit
6ae6dc22d2d1 ("usb: hub: Fix usb enumeration issue due to address0
race")
CC: stable@vger.kernel.org # 5.4+
Suggested-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Tested-by: Chris Chiu <chris.chiu@canonical.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Link: https://lore.kernel.org/r/20220510091630.16564-2-kishon@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Albert Wang [Wed, 18 May 2022 06:13:15 +0000 (14:13 +0800)]
usb: dwc3: gadget: Move null pinter check to proper place
commit
3c5880745b4439ac64eccdb040e37fc1cc4c5406 upstream.
When dwc3_gadget_ep_cleanup_completed_requests() called to
dwc3_gadget_giveback() where the dwc3 lock is released, other thread is
able to execute. In this situation, usb_ep_disable() gets the chance to
clear endpoint descriptor pointer which leds to the null pointer
dereference problem. So needs to move the null pointer check to a proper
place.
Example call stack:
Thread#1:
dwc3_thread_interrupt()
spin_lock
-> dwc3_process_event_buf()
-> dwc3_process_event_entry()
-> dwc3_endpoint_interrupt()
-> dwc3_gadget_endpoint_trbs_complete()
-> dwc3_gadget_ep_cleanup_completed_requests()
...
-> dwc3_giveback()
spin_unlock
Thread#2 executes
Thread#2:
configfs_composite_disconnect()
-> __composite_disconnect()
-> ffs_func_disable()
-> ffs_func_set_alt()
-> ffs_func_eps_disable()
-> usb_ep_disable()
wait for dwc3 spin_lock
Thread#1 released lock
clear endpoint.desc
Fixes:
26288448120b ("usb: dwc3: gadget: Fix null pointer exception")
Cc: stable <stable@kernel.org>
Signed-off-by: Albert Wang <albertccwang@google.com>
Link: https://lore.kernel.org/r/20220518061315.3359198-1-albertccwang@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Walleij [Mon, 16 May 2022 09:14:24 +0000 (11:14 +0200)]
usb: isp1760: Fix out-of-bounds array access
commit
26ae2c942b5702f2e43d36b2a4389cfb7d616b6a upstream.
Running the driver through kasan gives an interesting splat:
BUG: KASAN: global-out-of-bounds in isp1760_register+0x180/0x70c
Read of size 20 at addr
f1db2e64 by task swapper/0/1
(...)
isp1760_register from isp1760_plat_probe+0x1d8/0x220
(...)
This happens because the loop reading the regmap fields for the
different ISP1760 variants look like this:
for (i = 0; i < HC_FIELD_MAX; i++) { ... }
Meaning it expects the arrays to be at least HC_FIELD_MAX - 1 long.
However the arrays isp1760_hc_reg_fields[], isp1763_hc_reg_fields[],
isp1763_hc_volatile_ranges[] and isp1763_dc_volatile_ranges[] are
dynamically sized during compilation.
Fix this by putting an empty assignment to the [HC_FIELD_MAX]
and [DC_FIELD_MAX] array member at the end of each array.
This will make the array one member longer than it needs to be,
but avoids the risk of overwriting whatever is inside
[HC_FIELD_MAX - 1] and is simple and intuitive to read. Also
add comments explaining what is going on.
Fixes:
1da9e1c06873 ("usb: isp1760: move to regmap for register access")
Cc: stable@vger.kernel.org
Cc: Rui Miguel Silva <rui.silva@linaro.org>
Cc: Dietmar Eggemann <dietmar.eggemann@arm.com>
Reviewed-by: Rui Miguel Silva <rui.silva@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20220516091424.391209-1-linus.walleij@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Monish Kumar R [Fri, 20 May 2022 13:00:44 +0000 (18:30 +0530)]
USB: new quirk for Dell Gen 2 devices
commit
97fa5887cf283bb75ffff5f6b2c0e71794c02400 upstream.
Add USB_QUIRK_NO_LPM and USB_QUIRK_RESET_RESUME quirks for Dell usb gen
2 device to not fail during enumeration.
Found this bug on own testing
Signed-off-by: Monish Kumar R <monish.kumar.r@intel.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220520130044.17303-1-monish.kumar.r@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Carl Yin(殷张成) [Thu, 19 May 2022 02:34:43 +0000 (02:34 +0000)]
USB: serial: option: add Quectel BG95 modem
commit
33b7af2f459df453feb0d44628d820c47fefe7a8 upstream.
The BG95 modem has 3 USB configurations that are configurable via the AT
command AT+QCFGEXT="usbnet",["ecm"|"modem"|"rmnet"] which make the modem
enumerate with the following interfaces, respectively:
"modem": Diag + GNSS + Modem + Modem
"ecm" : Diag + GNSS + Modem + ECM
"rmnet": Diag + GNSS + Modem + QMI
Don't support Full QMI messages (e.g WDS_START_NETWORK_INTERFACE)
A detailed description of the USB configuration for each mode follows:
+QCFGEXT: "usbnet","modem"
--------------------------
T: Bus=01 Lev=02 Prnt=02 Port=01 Cnt=01 Dev#= 3 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=2c7c ProdID=0700 Rev= 0.00
S: Manufacturer=Quectel, Incorporated
S: Product=Quectel LPWA Module
S: SerialNumber=
884328a2
C:* #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=83(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=fe Prot=ff Driver=option
E: Ad=85(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
+QCFGEXT: "usbnet","ecm"
------------------------
T: Bus=01 Lev=02 Prnt=02 Port=01 Cnt=01 Dev#= 4 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=2c7c ProdID=0700 Rev= 0.00
S: Manufacturer=Quectel, Incorporated
S: Product=Quectel LPWA Module
S: SerialNumber=
884328a2
C:* #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA
A: FirstIf#= 3 IfCount= 2 Cls=02(comm.) Sub=00 Prot=00
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=83(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=06 Prot=00 Driver=cdc_ether
E: Ad=85(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
I: If#= 4 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
I:* If#= 4 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
+QCFGEXT: "usbnet","rmnet"
--------------------------
T: Bus=01 Lev=02 Prnt=02 Port=01 Cnt=01 Dev#= 4 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=2c7c ProdID=0700 Rev= 0.00
S: Manufacturer=Quectel, Incorporated
S: Product=Quectel LPWA Module
S: SerialNumber=
884328a2
C:* #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=83(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
E: Ad=85(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Signed-off-by: Carl Yin <carl.yin@quectel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Tue, 17 May 2022 16:17:36 +0000 (18:17 +0200)]
USB: serial: pl2303: fix type detection for odd device
commit
e82e7c6dde91acd6748d672a44dc1980ce239f86 upstream.
At least one pl2303 device has a bcdUSB of 1.0.1 which most likely was
was intended as 1.1.
Allow bcdDevice 1.0.1 but interpret it as 1.1.
Fixes:
1e9faef4d26d ("USB: serial: pl2303: fix HX type detection")
Cc: stable@vger.kernel.org # 5.13
Link: https://lore.kernel.org/linux-usb/CAJixRzqf4a9-ZKZDgWxicc_BpfdZVE9qqGmkiO7xEstOXUbGvQ@mail.gmail.com
Reported-by: Gary van der Merwe <gary.vandermerwe@fnb.co.za>
Link: https://lore.kernel.org/r/20220517161736.13313-1-johan@kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Takashi Iwai [Wed, 25 May 2022 13:12:03 +0000 (15:12 +0200)]
ALSA: usb-audio: Cancel pending work at closing a MIDI substream
commit
0125de38122f0f66bf61336158d12a1aabfe6425 upstream.
At closing a USB MIDI output substream, there might be still a pending
work, which would eventually access the rawmidi runtime object that is
being released. For fixing the race, make sure to cancel the pending
work at closing.
Reported-by: syzbot+6912c9592caca7ca0e7d@syzkaller.appspotmail.com
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/000000000000e7e75005dfd07cf6@google.com
Link: https://lore.kernel.org/r/20220525131203.11299-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Marios Levogiannis [Mon, 30 May 2022 07:41:31 +0000 (10:41 +0300)]
ALSA: hda/realtek - Fix microphone noise on ASUS TUF B550M-PLUS
commit
9bfa7b36343c7d84370bc61c9ed774635b05e4eb upstream.
Set microphone pins 0x18 (rear) and 0x19 (front) to VREF_50 to fix the
microphone noise on ASUS TUF B550M-PLUS which uses the ALCS1200A codec.
The initial value was VREF_80.
The same issue is also present on Windows using both the default Windows
driver and all tested Realtek drivers before version 6.0.9049.1. Comparing
Realtek driver 6.0.9049.1 (the first one without the microphone noise) to
Realtek driver 6.0.9047.1 (the last one with the microphone noise)
revealed that the fix is the result of setting pins 0x18 and 0x19 to
VREF_50.
This fix may also work for other boards that have been reported to have
the same microphone issue and use the ALC1150 and ALCS1200A codecs, since
these codecs are similar and the fix in the Realtek driver on Windows is
common for both. However, it is currently enabled only for ASUS TUF
B550M-PLUS as this is the only board that could be tested.
Signed-off-by: Marios Levogiannis <marios.levogiannis@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220530074131.12258-1-marios.levogiannis@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rik van der Kemp [Fri, 27 May 2022 12:07:26 +0000 (14:07 +0200)]
ALSA: hda/realtek: Enable 4-speaker output for Dell XPS 15 9520 laptop
commit
15dad62f4bdb5dc0f0efde8181d680db9963544c upstream.
The 2022-model XPS 15 appears to use the same 4-speakers-on-ALC289
audio setup as the Dell XPS 15 9510, so requires the same quirk to
enable woofer output. Tested on my own 9520.
[ Move the entry to the right position in the SSID order -- tiwai ]
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=216035
Cc: <stable@vger.kernel.org>
Signed-off-by: Rik van der Kemp <rik@upto11.nl>
Link: https://lore.kernel.org/r/181056a137b.d14baf90133058.8425453735588429828@upto11.nl
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kailang Yang [Tue, 24 May 2022 08:14:04 +0000 (16:14 +0800)]
ALSA: hda/realtek - Add new type for ALC245
commit
60571929d06b028800f27b51a7c81de1144944cf upstream.
Add new type for ALC245.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/cef26a7cd3d146eb96a3994ce79e34d2@realtek.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Nathan Chancellor [Mon, 16 May 2022 21:45:21 +0000 (14:45 -0700)]
riscv: Move alternative length validation into subsection
commit
61114e734ccb804bc12561ab4020745e02c468c2 upstream.
After commit
49b290e430d3 ("riscv: prevent compressed instructions in
alternatives"), builds with LLVM's integrated assembler fail:
In file included from arch/riscv/mm/init.c:10:
In file included from ./include/linux/mm.h:29:
In file included from ./include/linux/pgtable.h:6:
In file included from ./arch/riscv/include/asm/pgtable.h:108:
./arch/riscv/include/asm/tlbflush.h:23:2: error: expected assembly-time absolute expression
ALT_FLUSH_TLB_PAGE(__asm__ __volatile__ ("sfence.vma %0" : : "r" (addr) : "memory"));
^
./arch/riscv/include/asm/errata_list.h:33:5: note: expanded from macro 'ALT_FLUSH_TLB_PAGE'
asm(ALTERNATIVE("sfence.vma %0", "sfence.vma", SIFIVE_VENDOR_ID, \
^
./arch/riscv/include/asm/alternative-macros.h:187:2: note: expanded from macro 'ALTERNATIVE'
_ALTERNATIVE_CFG(old_content, new_content, vendor_id, errata_id, CONFIG_k)
^
./arch/riscv/include/asm/alternative-macros.h:113:2: note: expanded from macro '_ALTERNATIVE_CFG'
__ALTERNATIVE_CFG(old_c, new_c, vendor_id, errata_id, IS_ENABLED(CONFIG_k))
^
./arch/riscv/include/asm/alternative-macros.h:110:2: note: expanded from macro '__ALTERNATIVE_CFG'
ALT_NEW_CONTENT(vendor_id, errata_id, enable, new_c)
^
./arch/riscv/include/asm/alternative-macros.h:99:3: note: expanded from macro 'ALT_NEW_CONTENT'
".org . - (889b - 888b) + (887b - 886b)\n" \
^
<inline asm>:26:6: note: instantiated into assembly here
.org . - (889b - 888b) + (887b - 886b)
^
This error happens because LLVM's integrated assembler has a one-pass
design, which means it cannot figure out the instruction lengths when
the .org directive is outside of the subsection that contains the
instructions, which was changed by the .option directives added by the
above change.
Move the .org directives before the .previous directive so that these
directives are always within the same subsection, which resolves the
failures and does not introduce any new issues with GNU as. This was
done for arm64 in commit
966a0acce2fc ("arm64/alternatives: move length
validation inside the subsection") and commit
22315a2296f4 ("arm64:
alternatives: Move length validation in alternative_{insn, endif}").
While there is no error from the assembly versions of the macro, they
appear to have the same problem so just make the same change there as
well so that there are no problems in the future.
Link: https://github.com/ClangBuiltLinux/linux/issues/1640
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20220516214520.3252074-1-nathan@kernel.org
Cc: stable@vger.kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tobias Klauser [Thu, 5 May 2022 08:18:15 +0000 (10:18 +0200)]
riscv: Wire up memfd_secret in UAPI header
commit
02d88b40cb2e9614e0117c3385afdce878f0d377 upstream.
Move the __ARCH_WANT_MEMFD_SECRET define added in commit
7bb7f2ac24a0
("arch, mm: wire up memfd_secret system call where relevant") to
<uapi/asm/unistd.h> so __NR_memfd_secret is defined when including
<unistd.h> in userspace.
This allows the memfd_secret selftest to pass on riscv.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Link: https://lore.kernel.org/r/20220505081815.22808-1-tklauser@distanz.ch
Fixes:
7bb7f2ac24a0 ("arch, mm: wire up memfd_secret system call where relevant")
Cc: stable@vger.kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Samuel Holland [Sat, 30 Apr 2022 03:00:23 +0000 (22:00 -0500)]
riscv: Fix irq_work when SMP is disabled
commit
2273272823db6f67d57761df8116ae32e7f05bed upstream.
irq_work is triggered via an IPI, but the IPI infrastructure is not
included in uniprocessor kernels. As a result, irq_work never runs.
Fall back to the tick-based irq_work implementation on uniprocessor
configurations.
Fixes:
298447928bb1 ("riscv: Support irq_work via self IPIs")
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20220430030025.58405-1-samuel@sholland.org
Cc: stable@vger.kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alexandre Ghiti [Mon, 6 Dec 2021 10:46:56 +0000 (11:46 +0100)]
riscv: Initialize thread pointer before calling C functions
commit
35d33c76d68dfacc330a8eb477b51cc647c5a847 upstream.
Because of the stack canary feature that reads from the current task
structure the stack canary value, the thread pointer register "tp" must
be set before calling any C function from head.S: by chance, setup_vm
and all the functions that it calls does not seem to be part of the
functions where the canary check is done, but in the following commits,
some functions will.
Fixes:
f2c9699f65557a31 ("riscv: Add STACKPROTECTOR supported")
Signed-off-by: Alexandre Ghiti <alexandre.ghiti@canonical.com>
Cc: stable@vger.kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Xianting Tian [Wed, 18 May 2022 01:34:28 +0000 (09:34 +0800)]
RISC-V: Mark IORESOURCE_EXCLUSIVE for reserved mem instead of IORESOURCE_BUSY
commit
e61bf5c071148c80d091f8e7220b3b9130780ae3 upstream.
Commit
00ab027a3b82 ("RISC-V: Add kernel image sections to the resource tree")
marked IORESOURCE_BUSY for reserved memory, which caused resource map
failed in subsequent operations of related driver, so remove the
IORESOURCE_BUSY flag. In order to prohibit userland mapping reserved
memory, mark IORESOURCE_EXCLUSIVE for it.
The code to reproduce the issue,
dts:
mem0: memory@
a0000000 {
reg = <0x0 0xa0000000 0 0x1000000>;
no-map;
};
&test {
status = "okay";
memory-region = <&mem0>;
};
code:
np = of_parse_phandle(pdev->dev.of_node, "memory-region", 0);
ret = of_address_to_resource(np, 0, &r);
base = devm_ioremap_resource(&pdev->dev, &r);
// base = -EBUSY
Fixes:
00ab027a3b82 ("RISC-V: Add kernel image sections to the resource tree")
Reported-by: Huaming Jiang <jianghuaming.jhm@alibaba-inc.com>
Reviewed-by: Guo Ren <guoren@kernel.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Co-developed-by: Nick Kossifidis <mick@ics.forth.gr>
Signed-off-by: Xianting Tian <xianting.tian@linux.alibaba.com>
Link: https://lore.kernel.org/r/20220518013428.1338983-1-xianting.tian@linux.alibaba.com
Cc: stable@vger.kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Helge Deller [Thu, 2 Jun 2022 11:55:26 +0000 (13:55 +0200)]
parisc/stifb: Keep track of hardware path of graphics card
commit
b046f984814af7985f444150ec28716d42d00d9a upstream.
Keep the pa_path (hardware path) of the graphics card in sti_struct and use
this info to give more useful info which card is currently being used.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org # v5.10+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Helge Deller [Thu, 2 Jun 2022 11:50:44 +0000 (13:50 +0200)]
parisc/stifb: Implement fb_is_primary_device()
commit
cf936af790a3ef5f41ff687ec91bfbffee141278 upstream.
Implement fb_is_primary_device() function, so that fbcon detects if this
framebuffer belongs to the default graphics card which was used to start
the system.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org # v5.10+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Niklas Cassel [Thu, 14 Apr 2022 09:10:18 +0000 (11:10 +0200)]
binfmt_flat: do not stop relocating GOT entries prematurely on riscv
commit
6045ab5fea4c849153ebeb0acb532da5f29d69c4 upstream.
bFLT binaries are usually created using elf2flt.
The linker script used by elf2flt has defined the .data section like the
following for the last 19 years:
.data : {
_sdata = . ;
__data_start = . ;
data_start = . ;
*(.got.plt)
*(.got)
FILL(0) ;
. = ALIGN(0x20) ;
LONG(-1)
. = ALIGN(0x20) ;
...
}
It places the .got.plt input section before the .got input section.
The same is true for the default linker script (ld --verbose) on most
architectures except x86/x86-64.
The binfmt_flat loader should relocate all GOT entries until it encounters
a -1 (the LONG(-1) in the linker script).
The problem is that the .got.plt input section starts with a GOTPLT header
(which has size 16 bytes on elf64-riscv and 8 bytes on elf32-riscv), where
the first word is set to -1. See the binutils implementation for riscv [1].
This causes the binfmt_flat loader to stop relocating GOT entries
prematurely and thus causes the application to crash when running.
Fix this by skipping the whole GOTPLT header, since the whole GOTPLT header
is reserved for the dynamic linker.
The GOTPLT header will only be skipped for bFLT binaries with flag
FLAT_FLAG_GOTPIC set. This flag is unconditionally set by elf2flt if the
supplied ELF binary has the symbol _GLOBAL_OFFSET_TABLE_ defined.
ELF binaries without a .got input section should thus remain unaffected.
Tested on RISC-V Canaan Kendryte K210 and RISC-V QEMU nommu_virt_defconfig.
[1] https://sourceware.org/git/?p=binutils-gdb.git;a=blob;f=bfd/elfnn-riscv.c;hb=binutils-2_38#l3275
Cc: <stable@vger.kernel.org>
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Link: https://lore.kernel.org/r/20220414091018.896737-1-niklas.cassel@wdc.com
Fixed-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/lkml/202204182333.OIUOotK8-lkp@intel.com
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Greg Kroah-Hartman [Mon, 6 Jun 2022 06:43:42 +0000 (08:43 +0200)]
Linux 5.15.45
Link: https://lore.kernel.org/r/20220603173820.663747061@linuxfoundation.org
Tested-by: Fox Chen <foxhlchen@gmail.com>
Tested-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Tested-by: Linux Kernel Functional Testing <lkft@linaro.org>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Bagas Sanjaya <bagasdotme@gmail.com>
Tested-by: Ron Economos <re@w6rz.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Takashi Iwai [Tue, 31 May 2022 13:07:49 +0000 (15:07 +0200)]
ALSA: usb-audio: Optimize TEAC clock quirk
commit
3753fcc22974affa26160ce1c46a6ebaaaa86758 upstream.
Maris found out that the quirk for TEAC devices to work around the
clock setup is needed to apply only when the base clock is changed,
e.g. from 48000-based clocks (48000, 96000, 192000, 384000) to
44100-based clocks (44100, 88200, 176400, 352800), or vice versa,
while switching to another clock with the same base clock doesn't need
the (forcible) interface setup.
This patch implements the optimization for the TEAC clock quirk to
avoid the unnecessary interface re-setup.
Fixes:
5ce0b06ae5e6 ("ALSA: usb-audio: Workaround for clock setup on TEAC devices")
Reported-by: Maris Abele <maris7abele@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220531130749.30357-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kumar Kartikeya Dwivedi [Sat, 19 Mar 2022 08:08:24 +0000 (13:38 +0530)]
bpf: Check PTR_TO_MEM | MEM_RDONLY in check_helper_mem_access
commit
97e6d7dab1ca4648821c790a2b7913d6d5d549db upstream.
The commit being fixed was aiming to disallow users from incorrectly
obtaining writable pointer to memory that is only meant to be read. This
is enforced now using a MEM_RDONLY flag.
For instance, in case of global percpu variables, when the BTF type is
not struct (e.g. bpf_prog_active), the verifier marks register type as
PTR_TO_MEM | MEM_RDONLY from bpf_this_cpu_ptr or bpf_per_cpu_ptr
helpers. However, when passing such pointer to kfunc, global funcs, or
BPF helpers, in check_helper_mem_access, there is no expectation
MEM_RDONLY flag will be set, hence it is checked as pointer to writable
memory. Later, verifier sets up argument type of global func as
PTR_TO_MEM | PTR_MAYBE_NULL, so user can use a global func to get around
the limitations imposed by this flag.
This check will also cover global non-percpu variables that may be
introduced in kernel BTF in future.
Also, we update the log message for PTR_TO_BUF case to be similar to
PTR_TO_MEM case, so that the reason for error is clear to user.
Fixes:
34d3a78c681e ("bpf: Make per_cpu_ptr return rdonly PTR_TO_MEM.")
Reviewed-by: Hao Luo <haoluo@google.com>
Signed-off-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Link: https://lore.kernel.org/r/20220319080827.73251-3-memxor@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kumar Kartikeya Dwivedi [Sat, 19 Mar 2022 08:08:25 +0000 (13:38 +0530)]
bpf: Reject writes for PTR_TO_MAP_KEY in check_helper_mem_access
commit
7b3552d3f9f6897851fc453b5131a967167e43c2 upstream.
It is not permitted to write to PTR_TO_MAP_KEY, but the current code in
check_helper_mem_access would allow for it, reject this case as well, as
helpers taking ARG_PTR_TO_UNINIT_MEM also take PTR_TO_MAP_KEY.
Fixes:
69c087ba6225 ("bpf: Add bpf_for_each_map_elem() helper")
Signed-off-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Link: https://lore.kernel.org/r/20220319080827.73251-4-memxor@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Yuntao Wang [Thu, 7 Apr 2022 13:04:23 +0000 (21:04 +0800)]
bpf: Fix excessive memory allocation in stack_map_alloc()
commit
b45043192b3e481304062938a6561da2ceea46a6 upstream.
The 'n_buckets * (value_size + sizeof(struct stack_map_bucket))' part of the
allocated memory for 'smap' is never used after the memlock accounting was
removed, thus get rid of it.
[ Note, Daniel:
Commit
b936ca643ade ("bpf: rework memlock-based memory accounting for maps")
moved `cost += n_buckets * (value_size + sizeof(struct stack_map_bucket))`
up and therefore before the bpf_map_area_alloc() allocation, sigh. In a later
step commit
c85d69135a91 ("bpf: move memory size checks to bpf_map_charge_init()"),
and the overflow checks of `cost >= U32_MAX - PAGE_SIZE` moved into
bpf_map_charge_init(). And then
370868107bf6 ("bpf: Eliminate rlimit-based
memory accounting for stackmap maps") finally removed the bpf_map_charge_init().
Anyway, the original code did the allocation same way as /after/ this fix. ]
Fixes:
b936ca643ade ("bpf: rework memlock-based memory accounting for maps")
Signed-off-by: Yuntao Wang <ytcoode@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20220407130423.798386-1-ytcoode@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Liu Jian [Sat, 16 Apr 2022 10:57:59 +0000 (18:57 +0800)]
bpf: Enlarge offset check value to INT_MAX in bpf_skb_{load,store}_bytes
commit
45969b4152c1752089351cd6836a42a566d49bcf upstream.
The data length of skb frags + frag_list may be greater than 0xffff, and
skb_header_pointer can not handle negative offset. So, here INT_MAX is used
to check the validity of offset. Add the same change to the related function
skb_store_bytes.
Fixes:
05c74e5e53f6 ("bpf: add bpf_skb_load_bytes helper")
Signed-off-by: Liu Jian <liujian56@huawei.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20220416105801.88708-2-liujian56@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Yuntao Wang [Sat, 30 Apr 2022 13:08:03 +0000 (21:08 +0800)]
bpf: Fix potential array overflow in bpf_trampoline_get_progs()
commit
a2aa95b71c9bbec793b5c5fa50f0a80d882b3e8d upstream.
The cnt value in the 'cnt >= BPF_MAX_TRAMP_PROGS' check does not
include BPF_TRAMP_MODIFY_RETURN bpf programs, so the number of
the attached BPF_TRAMP_MODIFY_RETURN bpf programs in a trampoline
can exceed BPF_MAX_TRAMP_PROGS.
When this happens, the assignment '*progs++ = aux->prog' in
bpf_trampoline_get_progs() will cause progs array overflow as the
progs field in the bpf_tramp_progs struct can only hold at most
BPF_MAX_TRAMP_PROGS bpf programs.
Fixes:
88fd9e5352fe ("bpf: Refactor trampoline update code")
Signed-off-by: Yuntao Wang <ytcoode@gmail.com>
Link: https://lore.kernel.org/r/20220430130803.210624-1-ytcoode@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Chuck Lever [Sat, 21 May 2022 23:06:13 +0000 (19:06 -0400)]
NFSD: Fix possible sleep during nfsd4_release_lockowner()
commit
ce3c4ad7f4ce5db7b4f08a1e237d8dd94b39180b upstream.
nfsd4_release_lockowner() holds clp->cl_lock when it calls
check_for_locks(). However, check_for_locks() calls nfsd_file_get()
/ nfsd_file_put() to access the backing inode's flc_posix list, and
nfsd_file_put() can sleep if the inode was recently removed.
Let's instead rely on the stateowner's reference count to gate
whether the release is permitted. This should be a reliable
indication of locks-in-use since file lock operations and
->lm_get_owner take appropriate references, which are released
appropriately when file locks are removed.
Reported-by: Dai Ngo <dai.ngo@oracle.com>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Trond Myklebust [Sat, 14 May 2022 14:08:10 +0000 (10:08 -0400)]
NFS: Memory allocation failures are not server fatal errors
commit
452284407c18d8a522c3039339b1860afa0025a8 upstream.
We need to filter out ENOMEM in nfs_error_is_fatal_on_server(), because
running out of memory on our client is not a server error.
Reported-by: Olga Kornievskaia <aglo@umich.edu>
Fixes:
2dc23afffbca ("NFS: ENOMEM should also be a fatal error.")
Cc: stable@vger.kernel.org
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Akira Yokosawa [Wed, 27 Apr 2022 09:28:39 +0000 (18:28 +0900)]
docs: submitting-patches: Fix crossref to 'The canonical patch format'
commit
6d5aa418b3bd42cdccc36e94ee199af423ef7c84 upstream.
The reference to `explicit_in_reply_to` is pointless as when the
reference was added in the form of "#15" [1], Section 15) was "The
canonical patch format".
The reference of "#15" had not been properly updated in a couple of
reorganizations during the plain-text SubmittingPatches era.
Fix it by using `the_canonical_patch_format`.
[1]:
2ae19acaa50a ("Documentation: Add "how to write a good patch summary" to SubmittingPatches")
Signed-off-by: Akira Yokosawa <akiyks@gmail.com>
Fixes:
5903019b2a5e ("Documentation/SubmittingPatches: convert it to ReST markup")
Fixes:
9b2c76777acc ("Documentation/SubmittingPatches: enrich the Sphinx output")
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: stable@vger.kernel.org # v4.9+
Link: https://lore.kernel.org/r/64e105a5-50be-23f2-6cae-903a2ea98e18@gmail.com
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>