review.tizen.org Git - platform/kernel/linux-starfive.git/log

tcp: start receiver buffer autotuning sooner

Previously receiver buffer auto-tuning starts after receiving
one advertised window amount of data. After the initial receiver
buffer was raised by patch a337531b942b ("tcp: up initial rmem to
128KB and SYN rwin to around 64KB"), the reciver buffer may take
too long to start raising. To address this issue, this patch lowers
the initial bytes expected to receive roughly the expected sender's
initial window.

Fixes: a337531b942b ("tcp: up initial rmem to 128KB and SYN rwin to around 64KB")
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch '100GbE' of git://git./linux/kernel/git/jkirsher/next-queue

Jeff Kirsher says:

====================
100GbE Intel Wired LAN Driver Updates 2018-10-01

This series contains updates to ice driver only.

Anirudh provides several changes to "prep" the driver for upcoming
features. Specifically, the functions that are used for PF VSI/netdev
setup will also be used in SR-IOV support and to allow the reuse of
these functions, code needs to move.

Dave provides the only other change in the series, updates the driver to
protect the reset patch in its entirety. This is done by adding the
various bit checks to determine if a reset is scheduled/initiated and
whether it came from the software or firmware.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

ice: Change pf state behavior to protect reset path

Currently, there is no bit, or set of bits, that protect the entirety
of the reset path.

If the reset is originated by the driver, then the relevant
one of the following bits will be set when the reset is scheduled:
__ICE_PFR_REQ
__ICE_CORER_REQ
__ICE_GLOBR_REQ
This bit will not be cleared until after the rebuild has completed.

If the reset is originated by the FW, then the first the driver knows of
it will be the reception of the OICR interrupt. The __ICE_RESET_OICR_RECV
bit will be set in the interrupt handler. This will also be the indicator
in a SW originated reset that we have completed the pre-OICR tasks and
have informed the FW that a reset was requested.

To utilize these bits, change the function:
ice_is_reset_recovery_pending()
to be:
ice_is_reset_in_progress()

The new function will check all of the above bits in the pf->state and
will return a true if one or more of these bits are set.

Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ice: Move common functions out of ice_main.c part 7/7

This patch completes the code move out of ice_main.c

The following top level functions and related dependency functions) were
moved to ice_lib.c:
ice_vsi_setup
ice_vsi_cfg_tc

The following functions were made static again:
ice_vsi_setup_vector_base
ice_vsi_alloc_q_vectors
ice_vsi_get_qs
void ice_vsi_map_rings_to_vectors
ice_vsi_alloc_rings
ice_vsi_set_rss_params
ice_vsi_set_num_qs
ice_get_free_slot
ice_vsi_init
ice_vsi_alloc_arrays

Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ice: Move common functions out of ice_main.c part 6/7

This patch continues the code move out of ice_main.c

The following top level functions (and related dependency functions) were
moved to ice_lib.c:
ice_vsi_setup_vector_base
ice_vsi_alloc_q_vectors
ice_vsi_get_qs

The following functions were made static again:
ice_vsi_free_arrays
ice_vsi_clear_rings

Also, in this patch, the netdev and NAPI registration logic was de-coupled
from the VSI creation logic (ice_vsi_setup) as for SR-IOV, while we want to
create VF VSIs using ice_vsi_setup, we don't want to create netdevs.

Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ice: Move common functions out of ice_main.c part 5/7

This patch continues the code move out of ice_main.c

The following top level functions (and related dependency functions) were
moved to ice_lib.c:
ice_vsi_clear
ice_vsi_close
ice_vsi_free_arrays
ice_vsi_map_rings_to_vectors

Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ice: Move common functions out of ice_main.c part 4/7

This patch continues the code move out of ice_main.c

The following top level functions (and related dependency functions) were
moved to ice_lib.c:
ice_vsi_alloc_rings
ice_vsi_set_rss_params
ice_vsi_set_num_qs
ice_get_free_slot
ice_vsi_init
ice_vsi_clear_rings
ice_vsi_alloc_arrays

Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ice: Move common functions out of ice_main.c part 3/7

This patch continues the code move out of ice_main.c

The following top level functions (and related dependency functions) were
moved to ice_lib.c:
ice_vsi_delete
ice_free_res
ice_get_res
ice_is_reset_recovery_pending
ice_vsi_put_qs
ice_vsi_dis_irq
ice_vsi_free_irq
ice_vsi_free_rx_rings
ice_vsi_free_tx_rings
ice_msix_clean_rings

Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ice: Move common functions out of ice_main.c part 2/7

This patch continues the code move out of ice_main.c

The following top level functions (and related dependency functions) were
moved to ice_lib.c:
ice_vsi_start_rx_rings
ice_vsi_stop_rx_rings
ice_vsi_stop_tx_rings
ice_vsi_cfg_rxqs
ice_vsi_cfg_txqs
ice_vsi_cfg_msix

Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ice: Move common functions out of ice_main.c part 1/7

The functions that are used for PF VSI/netdev setup will also be used
for SR-IOV support. To allow reuse of these functions, move these
functions out of ice_main.c to ice_common.c/ice_lib.c

This move is done across multiple patches. Each patch moves a few
functions and may have minor adjustments. For example, a function that was
previously static in ice_main.c will be made non-static temporarily in
its new location to allow the driver to build cleanly. These adjustments
will be removed in subsequent patches where more code is moved out of
ice_main.c

In this particular patch, the following functions were moved out of
ice_main.c:
int ice_add_mac_to_list
ice_free_fltr_list
ice_stat_update40
ice_stat_update32
ice_update_eth_stats
ice_vsi_add_vlan
ice_vsi_kill_vlan
ice_vsi_manage_vlan_insertion
ice_vsi_manage_vlan_stripping

Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

openvswitch: Use correct reply values in datapath and vport ops

This patch fixes the bug that all datapath and vport ops are returning
wrong values (OVS_FLOW_CMD_NEW or OVS_DP_CMD_NEW) in their replies.

Signed-off-by: Yifeng Sun <pkusunyifeng@gmail.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

tls: Remove redundant vars from tls record structure

Structure 'tls_rec' contains sg_aead_in and sg_aead_out which point
to a aad_space and then chain scatterlists sg_plaintext_data,
sg_encrypted_data respectively. Rather than using chained scatterlists
for plaintext and encrypted data in aead_req, it is efficient to store
aad_space in sg_encrypted_data and sg_plaintext_data itself in the
first index and get rid of sg_aead_in, sg_aead_in and further chaining.

This requires increasing size of sg_encrypted_data & sg_plaintext_data
arrarys by 1 to accommodate entry for aad_space. The code which uses
sg_encrypted_data and sg_plaintext_data has been modified to skip first
index as it points to aad_space.

Signed-off-by: Vakul Garg <vakul.garg@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'tipc-next'

Jon Maloy says:

====================
tipc: make connection setup more robust

In this series we make a few improvements to the connection setup and
probing mechanism, culminating in the last commit where we make it
possible for a client socket to make multiple setup attempts in case
it encounters receive buffer overflow at the listener socket.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

tipc: buffer overflow handling in listener socket

Default socket receive buffer size for a listener socket is 2Mb. For
each arriving empty SYN, the linux kernel allocates a 768 bytes buffer.
This means that a listener socket can serve maximum 2700 simultaneous
empty connection setup requests before it hits a receive buffer
overflow, and much fewer if the SYN is carrying any significant
amount of data.

When this happens the setup request is rejected, and the client
receives an ECONNREFUSED error.

This commit mitigates this problem by letting the client socket try to
retransmit the SYN message multiple times when it sees it rejected with
the code TIPC_ERR_OVERLOAD. Retransmission is done at random intervals
in the range of [100 ms, setup_timeout / 4], as many times as there is
room for within the setup timeout limit.

Signed-off-by: Tung Nguyen <tung.q.nguyen@dektech.com.au>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tipc: add SYN bit to connection setup messages

Messages intended for intitating a connection are currently
indistinguishable from regular datagram messages. The TIPC
protocol specification defines bit 17 in word 0 as a SYN bit
to allow sanity check of such messages in the listening socket,
but this has so far never been implemented.

We do that in this commit.

Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tipc: refactor function tipc_sk_filter_connect()

We refactor the function tipc_sk_filter_connect(), both to make it
more readable and as a preparation for the next commit.

Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tipc: refactor function tipc_sk_timeout()

We refactor this function as a preparation for the coming commits in
the same series.

Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tipc: refactor function tipc_msg_reverse()

The function tipc_msg_reverse() is reversing the header of a message
while reusing the original buffer. We have seen at several occasions
that this may have unfortunate side effects when the buffer to be
reversed is a clone.

In one of the following commits we will again need to reverse cloned
buffers, so this is the right time to permanently eliminate this
problem. In this commit we let the said function always consume the
original buffer and replace it with a new one when applicable.

Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tcp: up initial rmem to 128KB and SYN rwin to around 64KB

Previously TCP initial receive buffer is ~87KB by default and
the initial receive window is ~29KB (20 MSS). This patch changes
the two numbers to 128KB and ~64KB (rounding down to the multiples
of MSS) respectively. The patch also simplifies the calculations s.t.
the two numbers are directly controlled by sysctl tcp_rmem[1]:

  1) Initial receiver buffer budget (sk_rcvbuf): while this should
     be configured via sysctl tcp_rmem[1], previously tcp_fixup_rcvbuf()
     always override and set a larger size when a new connection
     establishes.

  2) Initial receive window in SYN: previously it is set to 20
     packets if MSS <= 1460. The number 20 was based on the initial
     congestion window of 10: the receiver needs twice amount to
     avoid being limited by the receive window upon out-of-order
     delivery in the first window burst. But since this only
     applies if the receiving MSS <= 1460, connection using large MTU
     (e.g. to utilize receiver zero-copy) may be limited by the
     receive window.

With this patch TCP memory configuration is more straight-forward and
more properly sized to modern high-speed networks by default. Several
popular stacks have been announcing 64KB rwin in SYNs as well.

Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

hns3: Another build fix.

drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c: In function ‘hclge_get_sset_count’:
drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c:496:31: error: ‘HNAE3_REVISION_ID_21’ undeclared (first use in this function); did you mean ‘FADT2_REVISION_ID’?
   if (hdev->pdev->revision >= HNAE3_REVISION_ID_21 ||
                               ^~~~~~~~~~~~~~~~~~~~
                               FADT2_REVISION_ID

Signed-off-by: David S. Miller <davem@davemloft.net>

hns3: Fix the build.

drivers/net/ethernet/hisilicon/hns3/hns3_ethtool.c: In function ‘hns3_self_test’:
drivers/net/ethernet/hisilicon/hns3/hns3_ethtool.c:278:15: error: ‘HNS3_SELF_TEST_TYPE_NUM’ undeclared (first use in this function); did you mean ‘HNS3_SELF_TEST_TPYE_NUM’?
  int st_param[HNS3_SELF_TEST_TYPE_NUM][2];
               ^~~~~~~~~~~~~~~~~~~~~~~
               HNS3_SELF_TEST_TPYE_NUM

Signed-off-by: David S. Miller <davem@davemloft.net>

ice: fix changing of ring descriptor size (ethtool -G)

rx_mini_pending was set to an incorrect value. This was causing EINVAL to
always be returned to 'ethtool -G'. The driver does not support mini or
jumbo rings so the respective settings should be zero.

Also, change the valid range of the number of descriptors in the rings to
make the code simpler and easier for users to understand (this removes the
valid settings of 8 and 16). Add a system log message indicating when the
number is rounded-up from what the user specifies with the 'ethtool -G'
command (i.e. when it is not a multiple of 32), and update the log message
when a user-provided value is out of range to also indicate the stride.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ice: Update to capabilities admin queue command

This patch makes a couple of changes in the way the driver uses the
"get capabilities" command.

1. Get device capabilities in addition to function capabilities

2. Align to latest spec by using cap_count to determine size of the
buffer in case of length error.

Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ice: Query the Tx scheduler node before adding it

Query the Tx scheduler tree node information from FW before adding it to
the driver's software database. This will keep the node information current
in driver.

Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ice: Update comment for ice_fltr_mgmt_list_entry

Previously the comment stated that VSI lists should be used when a
second VSI becomes a subscriber to the "VLAN address". VSI lists
are always used for VLAN membership, so replace "VLAN address" with
"MAC address". Also note that VLAN(s) always use VSI list rules.

Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ice: update fw version check logic

We have MAX_FW_API_VER_BRANCH, MAX_FW_API_VER_MAJOR, and
MAX_FW_API_VER_MINOR that we use in ice_controlq.h to test when a
firmware version is newer than expected. This is currently tested by
comparing each field separately. Thus, we compare the branch field
against the MAX_FW_API_VER_BRANCH, and so forth.

This means that currently, if we suppose that the max firmware version
is defined as 0.2.1, i.e.

Then firmware 0.1.3 will fail to load. This is because the minor version
3 is greater than the max minor version 1.

This is not intuitive, because of the notion that increasing the major
firmware version to 2 should mean any firmware version with a major
version is less than 2 should be considered older than 2...

In order to allow both 0.2.1 and 0.1.3 to load, you would have to define
the "max" firmware version as 0.2.3.. It is possible that such
a firmware version doesn't even exist yet!

Fix this by replacing the current logic with an updated check that
behaves as follows:

First, we check the major version. If it is greater than the expected
version, then we prevent driver load. Additionally, a warning message is
logged to indicate to the system administrator that they need to update
their driver. This is now the only case where the driver will refuse to
load.

Second, if the major version is less than the expected version, we log
an information message indicating the NVM should be updated.

Third, if the major version is exact, we'll then check the minor
version. If the minor version is more than two versions less than
expected, we log an information message indicating the NVM should be
updated. If it is more than two versions greater than the expected
version, we log an information message that the driver should be
updated.

To support this, the ice_aq_ver_check function needs its signature
updated to pass the HW structure. Since we now pass this structure,
there is no need to pass the firmware API versions separately.

Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ice: update branding strings and supported device ids

Update branding strings and remove device ids 0x1594 and 0x1595.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ice: replace unnecessary memcpy with direct assignment

Direct assignment is preferred over a memcpy()

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ice: use [sr]q.count when checking if queue is initialized

When shutting down the controlqs, we check if they are initialized
before we shut them down and destroy the lock. This is important, as it
prevents attempts to access the lock of an already shutdown queue.

Unfortunately, we checked rq.head and sq.head as the value to determine
if the queue was initialized. This doesn't work, because head is not
reset when the queue is shutdown. In some flows, the adminq will have
already been shut down prior to calling ice_shutdown_all_ctrlqs. This
can result in a crash due to attempting to access the already destroyed
mutex.

Fix this by using rq.count and sq.count instead. Indeed, ice_shutdown_sq
and ice_shutdown_rq already indicate that this is the value we should be
using to determine of the queue was initialized.

Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

qed: fix spelling mistake "b_cb_registred" -> "b_cb_registered"

Trivial fix to spelling mistake struct field name, rename it.

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch '100GbE' of git://git./linux/kernel/git/jkirsher/next-queue

Jeff Kirsher says:

====================
100GbE Intel Wired LAN Driver Updates 2018-09-27

This series contains fixes to the ice driver only.

Jake fixes a potential crash due to attempting to access the mutex which
is already destroyed.  Fix this by using rq.count and sq.count to
determine if the queue was initialized.  Fixed the current logic for
checking the firmware version to properly handle situations when
firmware major/minor versions differ and when the branch version
differs.

Bruce replaces a memcpy() with a direct assignment, which is preferred.
Also updated the branding strings and device ids supported by the
driver.  Fixed the "ethtool -G" command in the driver, which was always
returning EINVAL when changing the descriptor ring size.

Brett update and clarified code comments.

Anirudh updates the driver to ensure we query the firmware for the
transmit scheduler node information before adding it to the driver
database, to ensure we have the current information.  Also update the
"get capabilities" command to get device and function capabilities.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

net: sched: make function qdisc_free_cb() static

Fixes the following sparse warning:

net/sched/sch_generic.c:944:6: warning:
symbol 'qdisc_free_cb' was not declared. Should it be static?

Fixes: 3a7d0d07a386 ("net: sched: extend Qdisc with rcu")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

selftests: forwarding: test for bridge sticky flag

This test adds an fdb entry with the sticky flag and sends traffic from
a different port with the same mac as a source address expecting the entry
to not change ports if the flag is operating correctly.

Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: bridge: explicitly zero is_sticky in fdb_create

We need to explicitly zero is_sticky when creating a new fdb, otherwise
we might get a stale value for a new entry.

Fixes: 435f2e7cc0b7 ("net: bridge: add support for sticky fdb entries")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'hns3-next'

Salil Mehta says:

====================
Cleanups, minor additions & fixes for HNS3 driver

This patch-set contains cleans-ups, minor changes and fixes to the HNS3 driver.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: Fix loss of coal configuration while doing reset

The user's coal configuration will be lost after reset, so the tx_coal
and rx_coal fields are added to the struct hns_nic_priv to save the coal
configuration and used to restore the user's configuration after the reset
is complete.

Fixes: bb6b94a896d4 ("net: hns3: Add reset interface implementation in client")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: Modify hns3_get_max_available_channels

The current hns3_get_max_available_channels returns the total number
of queues for the device, which makes ethtool -L set the number of queues
per channel queues incorrectly, so hns3_get_max_available_channels should
return the maximum available number of queues per channel, depending on
the total number of queues allocated and the hardware configurations.

Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: Change return type of hclge_tm_schd_info_update()

hclge_tm_schd_info_update should return an error when num_tc is greater
than alloc_tqps.

This patch changes the return type of hnae3_register_ae_algo from void
to int.

Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: Fix for netdev not up problem when setting mtu

Currently hns3_nic_change_mtu will try to down the netdev before
setting mtu, and it does not up the netdev when the setting fails,
which causes netdev not up problem.

This patch fixes it by not returning when the setting fails.

Fixes: a8e8b7ff3517 ("net: hns3: Add support to change MTU in HNS3 hardware")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: Fix for packet buffer setting bug

The hardware expects a unit of 128 bytes when setting
packet buffer. When calculating the packet buffer size,
hclge_rx_buffer_calc does not round up the size as a unit
of 128 byte, which may casue packet lost problem when stress
testing.

This patch fixes it by rounding up packet size when calculating.

Fixes: 46a3df9f9718 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: Add serdes parallel inner loopback support

This patch adds serdes parallel inner loopback support for self test.

Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: Rename mac loopback to app loopback

In fact, our implementation of mac loopback is the implementation of app
loopback now. Current name is wrong. This patch renames mac loopback to
app loopback.

Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: Rename loop mode

Our loop mode includes mac loop, serdes loop and phy loop. Not all of them
are related with mac. This patch corrects their names.

Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: Set extra mac address of pause param for HW

The extra mac address of pause param is used to do double check
for pause frame. This patch set it to HW. If we do not do that,
pfc pause frame will be transferred protocol stack when normal
flow control mode is enabled.

Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: Add support for sctp checksum offload

This patch adds support for sctp checksum offload.

Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: b53: Fix build with B53_SRAB enabled and B53_SERDES=m

When B53_SERDES is a loadable module, a built-in srab driver still
cannot reach it, so the previous fix is incomplete:

b53_srab.c:(.text+0x3f4): undefined reference to `b53_serdes_init'
drivers/net/dsa/b53/b53_srab.o:(.rodata+0xe64): undefined reference to `b53_serdes_link_state'
drivers/net/dsa/b53/b53_srab.o:(.rodata+0xe74): undefined reference to `b53_serdes_link_set'
drivers/net/dsa/b53/b53_srab.o:(.rodata+0xe88): undefined reference to `b53_serdes_an_restart'
drivers/net/dsa/b53/b53_srab.o:(.rodata+0xea0): undefined reference to `b53_serdes_phylink_validate'
drivers/net/dsa/b53/b53_srab.o:(.rodata+0xea4): undefined reference to `b53_serdes_config'

Add a Kconfig dependency that forces srab to also be a module
in this case, but allow it to be built-in when serdes is
disabled or built-in.

Fixes: 7a8c7f5c30f9 ("net: dsa: b53: Fix build with B53_SRAB enabled and not B53_SERDES")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: phy: mdio-bcm-unimac: mark PM functions as __maybe_unused

The newly added runtime-pm support causes a harmless warning
when CONFIG_PM is disabled:

drivers/net/phy/mdio-bcm-unimac.c:330:12: error: 'unimac_mdio_resume' defined but not used [-Werror=unused-function]
static int unimac_mdio_resume(struct device *d)
drivers/net/phy/mdio-bcm-unimac.c:321:12: error: 'unimac_mdio_suspend' defined but not used [-Werror=unused-function]
static int unimac_mdio_suspend(struct device *d)

Marking the functions as __maybe_unused is the easiest workaround
and avoids adding #ifdef checks.

Fixes: b78ac6ecd1b6 ("net: phy: mdio-bcm-unimac: Allow configuring MDIO clock divider")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

phy: mscc: fix printf format

gcc points out that the length of the temporary buffer may not be sufficient for
large numbers of leds:

drivers/net/phy/mscc.c: In function 'vsc85xx_probe':
drivers/net/phy/mscc.c:460:45: error: '-mode' directive writing 5 bytes into a region of size between 0 and 9 [-Werror=format-overflow=]
   ret = sprintf(led_dt_prop, "vsc8531,led-%d-mode", i);
                                             ^~~~~
drivers/net/phy/mscc.c:460:9: note: 'sprintf' output between 19 and 28 bytes into a destination of size 22
   ret = sprintf(led_dt_prop, "vsc8531,led-%d-mode", i);
         ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

While we can make a reasonable assumption that the number of LEDs is small,
the cost of making the buffer a little bigger is insignificant as well.

Fixes: 11bfdabb7ff5 ("net: phy: mscc: factorize code for LEDs mode")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: ethernet: dpaa: remove unused variables

The patch that removed the only users of the oldadv/newadv variables
accidentally left the now-unused declarations behind:

drivers/net/ethernet/freescale/dpaa/dpaa_ethtool.c: In function 'dpaa_set_pauseparam':
drivers/net/ethernet/freescale/dpaa/dpaa_ethtool.c:185:14: error: unused variable 'oldadv' [-Werror=unused-variable]
drivers/net/ethernet/freescale/dpaa/dpaa_ethtool.c:185:6: error: unused variable 'newadv' [-Werror=unused-variable]

Fixes: 70814e819c11 ("net: ethernet: Add helper for set_pauseparam for Asym Pause")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: aquantia: Make function aq_fw1x_set_power() static

Fixes the following sparse warning:

drivers/net/ethernet/aquantia/atlantic/hw_atl/hw_atl_utils.c:873:5: warning:
symbol 'aq_fw1x_set_power' was not declared. Should it be static?

Fixes: a0da96c08cfa ("net: aquantia: implement WOL support")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/tls: Make function get_rec() static

Fixes the following sparse warning:

net/tls/tls_sw.c:655:16: warning:
symbol 'get_rec' was not declared. Should it be static?

Fixes: a42055e8d2c3 ("net/tls: Add support for async encryption of records for performance")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/core: make function ___gnet_stats_copy_basic() static

Fixes the following sparse warning:

net/core/gen_stats.c:166:1: warning:
symbol '___gnet_stats_copy_basic' was not declared. Should it be static?

Fixes: 5e111210a443 ("net/core: Add new basic hardware counter")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Eelco Chaudron <echaudro@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: xen-netback: fix return type of ndo_start_xmit function

The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.

Found by coccinelle.

Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qed: Remove set but not used variable 'p_archipelago'

Fixes gcc '-Wunused-but-set-variable' warning:

drivers/net/ethernet/qlogic/qed/qed_ooo.c: In function 'qed_ooo_delete_isles':
drivers/net/ethernet/qlogic/qed/qed_ooo.c:354:30: warning:
variable 'p_archipelago' set but not used [-Wunused-but-set-variable]

drivers/net/ethernet/qlogic/qed/qed_ooo.c: In function 'qed_ooo_join_isles':
drivers/net/ethernet/qlogic/qed/qed_ooo.c:463:30: warning:
variable 'p_archipelago' set but not used [-Wunused-but-set-variable]

Since commit 1eec2437d14c ("qed: Make OOO archipelagos into an array"),
'p_archipelago' is no longer in use.

Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: ovs: fix return type of ndo_start_xmit function

The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.

Found by coccinelle.

Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'netlink-nested-policy-validation'

Johannes Berg says:

====================
netlink: nested policy validation

This adds nested policy validation, which lets you specify the
nested attribute type, e.g. NLA_NESTED with sub-policy, or the
new NLA_NESTED_ARRAY with sub-sub-policy.

Changes in v2:
* move setting the bad attr pointer/message into validate_nla()
* remove the recursion patch since that's no longer needed
* simply skip the generic bad attr pointer/message setting in
   case of nested nla_validate() failing since that could fail
   only due to validate_nla() failing inside, which already sets
   the extack information

Changes in v3:
* fix NLA_REJECT to have an error message if none is in policy
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

netlink: add nested array policy validation

Sometimes nested netlink attributes are just used as arrays, with
the nla_type() of each not being used; we have this in nl80211 and
e.g. NFTA_SET_ELEM_LIST_ELEMENTS.

Add the ability to validate this type of message directly in the
policy, by adding the type NLA_NESTED_ARRAY which does exactly
this: require a first level of nesting but ignore the attribute
type, and then inside each require a second level of nested and
validate those attributes against a given policy (if present).

Note that some nested array types actually require that all of
the entries have the same index, this is possible to express in
a nested policy already, apart from the validation that only the
one allowed type is used.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

netlink: allow NLA_NESTED to specify nested policy to validate

Now that we have a validation_data pointer, and the len field in
the policy is unused for NLA_NESTED, we can allow using them both
to have nested validation. This can be nice in code, although we
still have to use nla_parse_nested() or similar which would also
take a policy; however, it also serves as documentation in the
policy without requiring a look at the code.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

netlink: move extack setting into validate_nla()

This unifies the code between nla_parse() which sets the bad
attribute pointer and an error message, and nla_validate()
which only sets the bad attribute pointer.

It also cleans up the code for NLA_REJECT and paves the way
for nested policy validation, as it will allow us to easily
skip setting the "generic" message without any extra args
like the **error_msg now, just passing the extack through is
now enough.

While at it, remove the unnecessary label in nla_parse().

Suggested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

netlink: make validation_data const

The validation data is only used within the policy that
should usually already be const, and isn't changed in any
code that uses it. Therefore, make the validation_data
pointer const.

While at it, remove the duplicate variable in the bitfield
validation that I'd otherwise have to change to const.

Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

netlink: remove NLA_NESTED_COMPAT

This isn't used anywhere, so we might as well get rid of it.

Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>