Sasha Neftin [Tue, 19 Nov 2019 11:44:19 +0000 (13:44 +0200)]
igc: Remove no need declaration of the igc_set_interrupt_capability
We want to avoid forward-declarations of function if possible.
Rearrange the igc_set_interrupt_capability function implementation.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Sasha Neftin [Tue, 19 Nov 2019 11:44:11 +0000 (13:44 +0200)]
igc: Remove no need declaration of the igc_alloc_mapped_page
We want to avoid forward-declarations of function if possible.
Rearrange the igc_alloc_mapped_page function implementation.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Sasha Neftin [Tue, 19 Nov 2019 11:44:01 +0000 (13:44 +0200)]
igc: Remove no need declaration of the igc_configure
We want to avoid forward-declarations of function if possible.
Rearrange the igc_configure function implementation.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Sasha Neftin [Tue, 19 Nov 2019 11:43:51 +0000 (13:43 +0200)]
igc: Remove no need declaration of the igc_set_default_mac_filter
We want to avoid forward-declarations of function if possible.
Rearrange the igc_set_default_mac_filter function implementation.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Sasha Neftin [Tue, 19 Nov 2019 11:43:41 +0000 (13:43 +0200)]
igc: Remove no need declaration of the igc_power_down_link
We want to avoid forward-declarations of function if possible.
Rearrange the igc_power_down_link function implementation.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Sasha Neftin [Tue, 19 Nov 2019 11:43:32 +0000 (13:43 +0200)]
igc: Remove no need declaration of the igc_clean_tx_ring
We want to avoid forward-declarations of function if possible.
Rearrange the igc_clean_tx_ring function implementation.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
David S. Miller [Sun, 5 Jan 2020 01:02:19 +0000 (17:02 -0800)]
Merge branch '100GbE' of git://git./linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
100GbE Intel Wired LAN Driver Updates 2020-01-03
This series contains updates to the ice driver only.
Brett adds support for UDP segmentation offload (USO) based on the work
Alex Duyck did for other Intel drivers. Refactored how the VF sets
spoof checking to resolve a couple of issues found in
ice_set_vf_spoofchk(). Adds the ability to track of the dflt_vsI
(default VSI), since we cannot have more than one default VSI. Add a
macro for commonly used "for loop" used repeatedly in the code. Cleaned
up and made the VF link flows all similar. Refactor the flows of adding
and deleting MAC addresses in order to simplify the logic for error
conditions and setting/clearing the VF's default MAC address field.
Michal moves the setting of the default ITR value from ice_cfg_itr() to
the function we allocate queue vectors. Adds support for saving and
restoring the ITR value for each queue. Adds a check for all invalid
or unused parameters to log the information and return an error.
Vignesh cleans up the driver where we were trying to write to read-only
registers for the receive flex descriptors.
Tony changes a netdev_info() to netdev_dbg() when the MTU value is
changed.
Bruce suppresses a coverity reported error that was not really an error
by adding a code comment.
Mitch adds a check for a NULL receive descriptor to resolve a coverity
reported issue.
Krzysztof prevents a potential general protection fault by adding a
boundary check to see if the queue id is greater than the size of a UMEM
array. Adds additional code comments to assist coverity in its scans to
prevent false positives.
Jake adds support for E822 devices to the driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jacob Keller [Tue, 17 Dec 2019 10:55:43 +0000 (02:55 -0800)]
ice: Add device ids for E822 devices
Add support for E822 devices
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Krzysztof Kazimierczak [Thu, 12 Dec 2019 11:13:07 +0000 (03:13 -0800)]
ice: Suppress Coverity warnings for xdp_rxq_info_reg
Coverity reports some of the calls to xdp_rxq_info_reg() as potential
issues, because the driver does not check its return value. However,
those calls are wrapped with "if (!xdp_rxq_info_is_reg(&ring->xdp_rxq))"
and this check alone is enough to be sure that the function will never
fail.
All possible states of xdp_rxq_info are:
- NEW,
- REGISTERED,
- UNREGISTERED,
- UNUSED.
The driver won't mark a queue as UNUSED under no circumstance, so the
return value can be ignored safely.
Add comments for Coverity right above calls to xdp_rxq_info_reg() to
suppress the warnings.
Signed-off-by: Krzysztof Kazimierczak <krzysztof.kazimierczak@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Krzysztof Kazimierczak [Thu, 12 Dec 2019 11:13:06 +0000 (03:13 -0800)]
ice: Add a boundary check in ice_xsk_umem()
In ice_xsk_umem(), variable qid which is later used as an array index,
is not validated for a possible boundary exceedance. Because of that,
a calling function might receive an invalid address, which causes
general protection fault when dereferenced.
To address this, add a boundary check to see if qid is greater than the
size of a UMEM array. Also, don't let user change vsi->num_xsk_umems
just by trying to setup a second UMEM if its value is already set up
(i.e. UMEM region has already been allocated for this VSI).
While at it, make sure that ring->zca.free pointer is always zeroed out
if there is no UMEM on a specified ring.
Signed-off-by: Krzysztof Kazimierczak <krzysztof.kazimierczak@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mitch Williams [Thu, 12 Dec 2019 11:13:05 +0000 (03:13 -0800)]
ice: add extra check for null Rx descriptor
In the case where the hardware gives us a null Rx descriptor, it is
theoretically possible that we could call one of our skb-construction
functions with no data pointer, which would cause a panic.
In real life, this will never happen - we only get null RX
descriptors as the final descriptor in a chain of otherwise-valid
descriptors. When this happens, the skb will be extant and we'll just
call ice_add_rx_frag(), which can deal with empty data buffers.
Unfortunately, Coverity does not have intimate knowledge of our
hardware, so we must add a check here.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bruce Allan [Thu, 12 Dec 2019 11:13:04 +0000 (03:13 -0800)]
ice: suppress checked_return error
Coverity reports an error that is not really an error; suppress it.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tony Nguyen [Thu, 12 Dec 2019 11:13:03 +0000 (03:13 -0800)]
ice: Demote MTU change print to debug
Following the changes of commit
12299132b3d3 ("net: ethernet: intel: Demote
MTU change prints to debug"), change the MTU change message to netdev_dbg()
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Brett Creeley [Thu, 12 Dec 2019 11:13:02 +0000 (03:13 -0800)]
ice: Enable ip link show on the PF to display VF unicast MAC(s)
Currently when there are SR-IOV VF(s) and the user does "ip link show <pf
interface>" the VF unicast MAC addresses all show 00:00:00:00:00:00
if the unicast MAC was set via VIRTCHNL (i.e. not administratively set
by the host PF).
This is misleading to the host administrator. Fix this by setting the
VF's dflt_lan_addr.addr when the VF's unicast MAC address is
configured via VIRTCHNL. There are a couple cases where we don't allow
the dflt_lan_addr.addr field to be written. First, If the VF's
pf_set_mac field is true and the VF is not trusted, then we don't allow
the dflt_lan_addr.addr to be modified. Second, if the
dflt_lan_addr.addr has already been set (i.e. via VIRTCHNL).
Also a small refactor was done to separate the flow for add and delete
MAC addresses in order to simplify the logic for error conditions
and set/clear the VF's dflt_lan_addr.addr field.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Brett Creeley [Thu, 12 Dec 2019 11:13:01 +0000 (03:13 -0800)]
ice: Fix VF link state when it's IFLA_VF_LINK_STATE_AUTO
Currently the flow for ice_set_vf_link_state() is not configuring link
the same as all other VF link configuration flows. Fix this by only
setting the necessary VF members in ice_set_vf_link_state() and then
call ice_vc_notify_link_state() to actually configure link for the
VF. This made ice_set_pfe_link_forced() unnecessary, so it was
deleted. Also, this commonizes the link flows for the VF to all call
ice_vc_notify_link_state().
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Vignesh Sridhar [Thu, 12 Dec 2019 11:13:00 +0000 (03:13 -0800)]
ice: Remove Rx flex descriptor programming
Remove Rx flex descriptor metadata and flag programming; per specification
these registers cannot be written to as they are read only.
Signed-off-by: Vignesh Sridhar <vignesh.sridhar@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Michal Swiatkowski [Thu, 12 Dec 2019 11:12:59 +0000 (03:12 -0800)]
ice: Return error on not supported ethtool -C parameters
Check for all unused parameters, if ethtool sent one of them,
print info about that and return error.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Michal Swiatkowski [Thu, 12 Dec 2019 11:12:58 +0000 (03:12 -0800)]
ice: Restore interrupt throttle settings after VSI rebuild
After each rebuild driver deallocates q_vectors, so the interrupt
throttle rate (ITR) settings get lost.
Create a function to save and restore ITR for each queue. If a user
increases the number of queues, restore all the previous queue
settings for each existing queue, and the additional queues will
get the default setting.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Michal Swiatkowski [Thu, 12 Dec 2019 11:12:57 +0000 (03:12 -0800)]
ice: Set default value for ITR in alloc function
When the user sets itr_setting to zero from ethtool -C, the driver changes
this value to default in ice_cfg_itr (for example after changing ring
param). Remove code that sets default value in ice_cfg_itr and move it to
place where the driver allocates q_vectors.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Brett Creeley [Thu, 12 Dec 2019 11:12:56 +0000 (03:12 -0800)]
ice: Add ice_for_each_vf() macro
Currently we do "for (i = 0; i < pf->num_alloc_vfs; i++)" all over the
place. Many other places use macros to contain this repeated for loop,
So create the macro ice_for_each_vf(pf, i) that does the same thing.
There were a couple places we were using one loop variable and a VF
iterator, which were changed to using a local variable within the
ice_for_each_vf() macro.
Also in ice_alloc_vfs() we were setting pf->num_alloc_vfs after doing
"for (i = 0; i < num_alloc_vfs; i++)". Instead assign pf->num_alloc_vfs
right after allocating memory for the pf->vf array.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Brett Creeley [Thu, 12 Dec 2019 11:12:55 +0000 (03:12 -0800)]
ice: Add code to keep track of current dflt_vsi
We can't have more than one default VSI so prevent another VSI from
overwriting the current dflt_vsi. This was achieved by adding the
following functions:
ice_is_dflt_vsi_in_use()
- Used to check if the default VSI is already being used.
ice_is_vsi_dflt_vsi()
- Used to check if VSI passed in is in fact the default VSI.
ice_set_dflt_vsi()
- Used to set the default VSI via a switch rule
ice_clear_dflt_vsi()
- Used to clear the default VSI via a switch rule.
Also, there was no need to introduce any locking because all mailbox
events and synchronization of switch filters for the PF happen in the
service task.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Brett Creeley [Thu, 12 Dec 2019 11:12:54 +0000 (03:12 -0800)]
ice: Fix VF spoofchk
There are many things wrong with the function
ice_set_vf_spoofchk().
1. The VSI being modified is the PF VSI, not the VF VSI.
2. We are enabling Rx VLAN pruning instead of Tx VLAN anti-spoof.
3. The spoofchk setting for each VF is not initialized correctly
or re-initialized correctly on reset.
To fix [1] we need to make sure we are modifying the VF VSI.
This is done by using the vf->lan_vsi_idx to index into the PF's
VSI array.
To fix [2] replace setting Rx VLAN pruning in ice_set_vf_spoofchk()
with setting Tx VLAN anti-spoof.
To Fix [3] we need to make sure the initial VSI settings match what
is done in ice_set_vf_spoofchk() for spoofchk=on. Also make sure
this also works for VF reset. This was done by modifying ice_vsi_init()
to account for the current spoofchk state of the VF VSI.
Because of these changes, Tx VLAN anti-spoof needs to be removed
from ice_cfg_vlan_pruning(). This is okay for the VF because this
is now controlled from the admin enabling/disabling spoofchk. For the
PF, Tx VLAN anti-spoof should not be set. This change requires us to
call ice_set_vf_spoofchk() when configuring promiscuous mode for
the VF which requires ice_set_vf_spoofchk() to move in order to prevent
a forward declaration prototype.
Also, add VLAN 0 by default when allocating a VF since the PF is unaware
if the guest OS is running the 8021q module. Without this, MDD events will
trigger on untagged traffic because spoofcheck is enabled by default. Due
to this change, ignore add/delete messages for VLAN 0 from VIRTCHNL since
this is added/deleted during VF initialization/teardown respectively and
should not be modified.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Brett Creeley [Thu, 12 Dec 2019 11:12:53 +0000 (03:12 -0800)]
ice: Support UDP segmentation offload
Based on the work done by Alex Duyck on other Intel drivers, add code to
support UDP segmentation offload (USO) for the ice driver.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
yu kuai [Fri, 3 Jan 2020 12:04:37 +0000 (20:04 +0800)]
bna: remove set but not used variable 'pgoff'
drivers/net/ethernet/brocade/bna/bfa_ioc.c: In function
‘bfa_ioc_fwver_clear’:
drivers/net/ethernet/brocade/bna/bfa_ioc.c:1127:13: warning: variable
‘pgoff’ set but not used [-Wunused-but-set-variable]
It is never used, and so can be removed.
Signed-off-by: yu kuai <yukuai3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ilias Apalodimas [Fri, 3 Jan 2020 11:40:32 +0000 (13:40 +0200)]
net: netsec: Change page pool nid to NUMA_NO_NODE
The current driver only exists on a non NUMA aware machine.
With
44768decb7c0 ("page_pool: handle page recycle for NUMA_NO_NODE condition")
applied we can safely change that to NUMA_NO_NODE and accommodate future
NUMA aware hardware using netsec network interface
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Xu Wang [Fri, 3 Jan 2020 09:28:16 +0000 (09:28 +0000)]
l2tp: Remove redundant BUG_ON() check in l2tp_pernet
Passing NULL to l2tp_pernet causes a crash via BUG_ON.
Dereferencing net in net_generic() also has the same effect.
This patch removes the redundant BUG_ON check on the same parameter.
Signed-off-by: Xu Wang <vulab@iscas.ac.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Xu Wang [Fri, 3 Jan 2020 09:20:40 +0000 (09:20 +0000)]
net: Remove redundant BUG_ON() check in phonet_pernet
Passing NULL to phonet_pernet causes a crash via BUG_ON.
Dereferencing net in net_generic() also has the same effect.
This patch removes the redundant BUG_ON check on the same parameter.
Signed-off-by: Xu Wang <vulab@iscas.ac.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Li RongQing [Fri, 3 Jan 2020 03:51:00 +0000 (11:51 +0800)]
net: remove the check argument from __skb_gro_checksum_convert
The argument is always ignored, so remove it.
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
YueHaibing [Fri, 3 Jan 2020 03:48:56 +0000 (03:48 +0000)]
ethtool: remove set but not used variable 'lsettings'
Fixes gcc '-Wunused-but-set-variable' warning:
net/ethtool/linkmodes.c: In function 'ethnl_set_linkmodes':
net/ethtool/linkmodes.c:326:32: warning:
variable 'lsettings' set but not used [-Wunused-but-set-variable]
struct ethtool_link_settings *lsettings;
^
It is never used, so remove it.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mao Wenan [Thu, 2 Jan 2020 14:02:27 +0000 (22:02 +0800)]
tcp: use REXMIT_NEW instead of magic number
REXMIT_NEW is a macro for "FRTO-style
transmit of unsent/new packets", this patch
makes it more readable.
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Po Liu [Thu, 2 Jan 2020 04:59:24 +0000 (04:59 +0000)]
enetc: add support time specific departure base on the qos etf
ENETC implement time specific departure capability, which enables
the user to specify when a frame can be transmitted. When this
capability is enabled, the device will delay the transmission of
the frame so that it can be transmitted at the precisely specified time.
The delay departure time up to 0.5 seconds in the future. If the
departure time in the transmit BD has not yet been reached, based
on the current time, the packet will not be transmitted.
This driver was loaded by Qos driver ETF. User could load it by tc
commands. Here are the example commands:
tc qdisc add dev eth0 root handle 1: mqprio \
num_tc 8 map 0 1 2 3 4 5 6 7 hw 1
tc qdisc replace dev eth0 parent 1:8 etf \
clockid CLOCK_TAI delta 30000 offload
These example try to set queue mapping first and then set queue 7
with 30us ahead dequeue time.
Then user send test frame should set SO_TXTIME feature for socket.
There are also some limitations for this feature in hardware:
- Transmit checksum offloads and time specific departure operation
are mutually exclusive.
- Time Aware Shaper feature (Qbv) offload and time specific departure
operation are mutually exclusive.
Signed-off-by: Po Liu <Po.Liu@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julia Lawall [Wed, 1 Jan 2020 17:49:44 +0000 (18:49 +0100)]
fsl/fman: use resource_size
Use resource_size rather than a verbose computation on
the end and start fields.
The semantic patch that makes these changes is as follows:
(http://coccinelle.lip6.fr/)
<smpl>
@@ struct resource ptr; @@
- (ptr.end + 1 - ptr.start)
+ resource_size(&ptr)
@@ struct resource *ptr; @@
- (ptr->end + 1 - ptr->start)
+ resource_size(ptr)
</smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julia Lawall [Wed, 1 Jan 2020 07:43:31 +0000 (08:43 +0100)]
ptp: ptp_clockmatrix: constify copied structure
The idtcm_caps structure is only copied into another structure,
so make it const.
The opportunity for this change was found using Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Tue, 31 Dec 2019 16:59:08 +0000 (16:59 +0000)]
sfc: Remove unnecessary dependencies on I2C
Only the SFC4000 code, now moved to sfc-falcon, needed I2C.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Acked-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 2 Jan 2020 23:51:22 +0000 (15:51 -0800)]
Merge branch 'tcp-Add-support-for-L3-domains-to-MD5-auth'
David Ahern says:
====================
tcp: Add support for L3 domains to MD5 auth
With VRF, the scope of network addresses is limited to the L3 domain
the device is associated. MD5 keys are based on addresses, so proper
VRF support requires an L3 domain to be considered for the lookups.
Leverage the new TCP_MD5SIG_EXT option to add support for a device index
to MD5 keys. The __tcpm_pad entry in tcp_md5sig is renamed to tcpm_ifindex
and a new flag, TCP_MD5SIG_FLAG_IFINDEX, in tcpm_flags determines if the
entry is examined. This follows what was done for MD5 and prefixes with
commits
8917a777be3b ("tcp: md5: add TCP_MD5SIG_EXT socket option to set a key address prefix")
6797318e623d ("tcp: md5: add an address prefix for key lookup")
Handling both a device AND L3 domain is much more complicated for the
response paths. This set focuses only on L3 support - requiring the
device index to be an l3mdev (ie, VRF). Support for slave devices can
be added later if desired, much like the progression of support for
sockets bound to a VRF and then bound to a device in a VRF. Kernel
code is setup to explicitly call out that current lookup is for an L3
index, while the uapi just references a device index allowing its
meaning to include other devices in the future.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Mon, 30 Dec 2019 22:14:33 +0000 (14:14 -0800)]
fcnal-test: Add TCP MD5 tests for VRF
Add tests for new TCP MD5 API for L3 domains (VRF).
A new namespace is added to create a duplicate configuration between
the VRF and default VRF to verify overlapping config is handled properly.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Mon, 30 Dec 2019 22:14:32 +0000 (14:14 -0800)]
fcnal-test: Add TCP MD5 tests
Add tests for existing TCP MD5 APIs - both single address
config and the new extended API for prefixes.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Mon, 30 Dec 2019 22:14:31 +0000 (14:14 -0800)]
nettest: Add support for TCP_MD5 extensions
Update nettest to implement TCP_MD5SIG_EXT for a prefix and a device.
Add a new option, -m, to specify a prefix and length to use with MD5
auth. The device option comes from the existing -d option. If either
are set and MD5 auth is requested, TCP_MD5SIG_EXT is used instead of
TCP_MD5SIG.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Mon, 30 Dec 2019 22:14:30 +0000 (14:14 -0800)]
nettest: Return 1 on MD5 failure for server mode
On failure to set MD5 password, do_server should return 1 so that the
program exits with 1 rather than 255. This used for negative testing
when adding MD5 with device option.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Mon, 30 Dec 2019 22:14:29 +0000 (14:14 -0800)]
net: Add device index to tcp_md5sig
Add support for userspace to specify a device index to limit the scope
of an entry via the TCP_MD5SIG_EXT setsockopt. The existing __tcpm_pad
is renamed to tcpm_ifindex and the new field is only checked if the new
TCP_MD5SIG_FLAG_IFINDEX is set in tcpm_flags. For now, the device index
must point to an L3 master device (e.g., VRF). The API and error
handling are setup to allow the constraint to be relaxed in the future
to any device index.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Mon, 30 Dec 2019 22:14:28 +0000 (14:14 -0800)]
tcp: Add l3index to tcp_md5sig_key and md5 functions
Add l3index to tcp_md5sig_key to represent the L3 domain of a key, and
add l3index to tcp_md5_do_add and tcp_md5_do_del to fill in the key.
With the key now based on an l3index, add the new parameter to the
lookup functions and consider the l3index when looking for a match.
The l3index comes from the skb when processing ingress packets leveraging
the helpers created for socket lookups, tcp_v4_sdif and inet_iif (and the
v6 variants). When the sdif index is set it means the packet ingressed a
device that is part of an L3 domain and inet_iif points to the VRF device.
For egress, the L3 domain is determined from the socket binding and
sk_bound_dev_if.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Mon, 30 Dec 2019 22:14:27 +0000 (14:14 -0800)]
ipv4/tcp: Pass dif and sdif to tcp_v4_inbound_md5_hash
The original ingress device index is saved to the cb space of the skb
and the cb is moved during tcp processing. Since tcp_v4_inbound_md5_hash
can be called before and after the cb move, pass dif and sdif to it so
the caller can save both prior to the cb move. Both are used by a later
patch.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Mon, 30 Dec 2019 22:14:26 +0000 (14:14 -0800)]
ipv6/tcp: Pass dif and sdif to tcp_v6_inbound_md5_hash
The original ingress device index is saved to the cb space of the skb
and the cb is moved during tcp processing. Since tcp_v6_inbound_md5_hash
can be called before and after the cb move, pass dif and sdif to it so
the caller can save both prior to the cb move. Both are used by a later
patch.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Mon, 30 Dec 2019 22:14:25 +0000 (14:14 -0800)]
ipv4/tcp: Use local variable for tcp_md5_addr
Extract the typecast to (union tcp_md5_addr *) to a local variable
rather than the current long, inline declaration with function calls.
No functional change intended.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Niu Xilei [Mon, 30 Dec 2019 09:52:22 +0000 (17:52 +0800)]
vxlan: Fix alignment and code style of vxlan.c
Fixed Coding function and style issues
Signed-off-by: Niu Xilei <niu_xilei@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 2 Jan 2020 23:40:14 +0000 (15:40 -0800)]
Merge branch 'mlxsw-Allow-setting-default-port-priority'
Ido Schimmel says:
====================
mlxsw: Allow setting default port priority
Petr says:
When LLDP APP TLV selector 1 (EtherType) is used with PID of 0, the
corresponding entry specifies "default application priority [...] when
application priority is not otherwise specified."
mlxsw currently supports this type of APP entry, but uses it only as a
fallback for unspecified DSCP rules. However non-IP traffic is prioritized
according to port-default priority, not according to the DSCP-to-prio
tables, and thus it's currently not possible to prioritize such traffic
correctly.
This patchset extends the use of the abovementioned APP entry to also set
default port priority (in patches #1 and #2) and then (in patch #3) adds a
selftest.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Sun, 29 Dec 2019 11:48:29 +0000 (13:48 +0200)]
selftests: mlxsw: Add a self-test for port-default priority
Send non-IP traffic to a port and observe that it gets prioritized
according to the lldptool app=$prio,1,0 rules.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Sun, 29 Dec 2019 11:48:28 +0000 (13:48 +0200)]
mlxsw: spectrum_dcb: Allow setting default port priority
When APP TLV selector 1 (EtherType) is used with PID of 0, the
corresponding entry specifies "default application priority [...] when
application priority is not otherwise specified."
mlxsw currently supports this type of APP entry, but uses it only as a
fallback for unspecified DSCP rules. However non-IP traffic is prioritized
according to port-default priority, not according to the DSCP-to-prio
tables, and thus it's currently not possible to prioritize such traffic
correctly.
Extend the use of the abovementioned APP entry to also set default port
priority.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Sun, 29 Dec 2019 11:48:27 +0000 (13:48 +0200)]
mlxsw: reg: Add QoS Port DSCP to Priority Mapping Register
Add QPDP. This register controls the port default Switch Priority and
Color. The default Switch Priority and Color are used for frames where the
trust state uses default values. Currently there are two cases where this
applies: a port is in trust-PCP state, but a packet arrives untagged; and a
port is in trust-DSCP state, but a non-IP packet arrives.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 2 Jan 2020 23:37:53 +0000 (15:37 -0800)]
Merge branch 'page_pool-NUMA-node-handling-fixes'
Jesper Dangaard Brouer says:
====================
page_pool: NUMA node handling fixes
The recently added NUMA changes (merged for v5.5) to page_pool, it both
contains a bug in handling NUMA_NO_NODE condition, and added code to
the fast-path.
This patchset fixes the bug and moves code out of fast-path. The first
patch contains a fix that should be considered for 5.5. The second
patch reduce code size and overhead in case CONFIG_NUMA is disabled.
Currently the NUMA_NO_NODE setting bug only affects driver 'ti_cpsw'
(drivers/net/ethernet/ti/), but after this patchset, we plan to move
other drivers (netsec and mvneta) to use NUMA_NO_NODE setting.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jesper Dangaard Brouer [Fri, 27 Dec 2019 17:13:24 +0000 (18:13 +0100)]
page_pool: help compiler remove code in case CONFIG_NUMA=n
When kernel is compiled without NUMA support, then page_pool NUMA
config setting (pool->p.nid) doesn't make any practical sense. The
compiler cannot see that it can remove the code paths.
This patch avoids reading pool->p.nid setting in case of !CONFIG_NUMA,
in allocation and numa check code, which helps compiler to see the
optimisation potential. It leaves update code intact to keep API the
same.
$ ./scripts/bloat-o-meter net/core/page_pool.o-numa-enabled \
net/core/page_pool.o-numa-disabled
add/remove: 0/0 grow/shrink: 0/3 up/down: 0/-113 (-113)
Function old new delta
page_pool_create 401 398 -3
__page_pool_alloc_pages_slow 439 426 -13
page_pool_refill_alloc_cache 425 328 -97
Total: Before=3611, After=3498, chg -3.13%
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jesper Dangaard Brouer [Fri, 27 Dec 2019 17:13:18 +0000 (18:13 +0100)]
page_pool: handle page recycle for NUMA_NO_NODE condition
The check in pool_page_reusable (page_to_nid(page) == pool->p.nid) is
not valid if page_pool was configured with pool->p.nid = NUMA_NO_NODE.
The goal of the NUMA changes in commit
d5394610b1ba ("page_pool: Don't
recycle non-reusable pages"), were to have RX-pages that belongs to the
same NUMA node as the CPU processing RX-packet during softirq/NAPI. As
illustrated by the performance measurements.
This patch moves the NAPI checks out of fast-path, and at the same time
solves the NUMA_NO_NODE issue.
First realize that alloc_pages_node() with pool->p.nid = NUMA_NO_NODE
will lookup current CPU nid (Numa ID) via numa_mem_id(), which is used
as the the preferred nid. It is only in rare situations, where
e.g. NUMA zone runs dry, that page gets doesn't get allocated from
preferred nid. The page_pool API allows drivers to control the nid
themselves via controlling pool->p.nid.
This patch moves the NAPI check to when alloc cache is refilled, via
dequeuing/consuming pages from the ptr_ring. Thus, we can allow placing
pages from remote NUMA into the ptr_ring, as the dequeue/consume step
will check the NUMA node. All current drivers using page_pool will
alloc/refill RX-ring from same CPU running softirq/NAPI process.
Drivers that control the nid explicitly, also use page_pool_update_nid
when changing nid runtime. To speed up transision to new nid the alloc
cache is now flushed on nid changes. This force pages to come from
ptr_ring, which does the appropate nid check.
For the NUMA_NO_NODE case, when a NIC IRQ is moved to another NUMA
node, we accept that transitioning the alloc cache doesn't happen
immediately. The preferred nid change runtime via consulting
numa_mem_id() based on the CPU processing RX-packets.
Notice, to avoid stressing the page buddy allocator and avoid doing too
much work under softirq with preempt disabled, the NUMA check at
ptr_ring dequeue will break the refill cycle, when detecting a NUMA
mismatch. This will cause a slower transition, but its done on purpose.
Fixes:
d5394610b1ba ("page_pool: Don't recycle non-reusable pages")
Reported-by: Li RongQing <lirongqing@baidu.com>
Reported-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 1 Jan 2020 05:43:31 +0000 (21:43 -0800)]
Merge branch '1GbE' of git://git./linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
1GbE Intel Wired LAN Driver Updates 2019-12-31
This series contains updates to e1000e, igb and igc only.
Robert Beckett provide an igb change to assist in keeping packets from
being dropped due to receive descriptor ring being full when receive
flow control is enabled. Create a separate function to setup SRRCTL to
ease in reuse and ensure that setting of the drop enable bit only if
receive flow control is not enabled.
Sasha adds support for scatter gather support in igc. Improve the
direct memory address mapping flow by optimizing/simplifying and more
clear. Update igc to use pci_release_mem_regions() instead of
pci_release_selected_regions(). Clean up function header comments to
align with the actual code. Adds support for 64 bit DMA access, to help
handle socket buffer fragments in high memory. Adds legacy power
management support in igc by implementing suspend, resume,
runtime_suspend/resume, and runtime_idle callbacks. Clean up references
to Serdes interface in igc since that interface is not supported for
i225 devices.
Alex replaces the pr_info calls with netdev_info in all cases related to
netdev link state, as suggested by Joe Perches.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Sasha Neftin [Mon, 2 Dec 2019 07:56:26 +0000 (09:56 +0200)]
igc: Remove serdes comments from a description of methods
Serdes interface is not applicable for i225 devices.
Remove this from comments and make comments more clearly.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Thu, 31 Oct 2019 16:58:51 +0000 (09:58 -0700)]
e1000e: Use netdev_info instead of pr_info for link messages
Replace the pr_info calls with netdev_info in all cases related to the
netdevice link state.
As a result of this patch the link messages will change as shown below.
Before:
e1000e: ens3 NIC Link is Down
e1000e: ens3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx
After:
e1000e 0000:00:03.0 ens3: NIC Link is Down
e1000e 0000:00:03.0 ens3: NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Sasha Neftin [Thu, 14 Nov 2019 07:54:46 +0000 (09:54 +0200)]
igc: Add legacy power management support
Add suspend, resume, runtime_suspend, runtime_resume and
runtime_idle callbacks implementation.
Reported-by: kbuild test robot <lpk@intel.com>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
David S. Miller [Tue, 31 Dec 2019 21:37:13 +0000 (13:37 -0800)]
Merge git://git./linux/kernel/git/netdev/net
Simple overlapping changes in bpf land wrt. bpf_helper_defs.h
handling.
Signed-off-by: David S. Miller <davem@davemloft.net>
Sasha Neftin [Wed, 13 Nov 2019 09:27:29 +0000 (11:27 +0200)]
igc: Add 64 bit DMA access support
On relevant platforms ndo_start_xmit can handle socket buffer
fragments in high memory
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Sasha Neftin [Tue, 12 Nov 2019 15:13:32 +0000 (17:13 +0200)]
igc: Fix parameter descriptions for a several functions
igc_watchdog, igc_set_interrupt_capability, igc_init_interrupt_scheme,
__igc_open and __igc_close parameter descriptions has not reflected
functions meaning. Add meaningful description.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Sasha Neftin [Mon, 11 Nov 2019 07:04:12 +0000 (09:04 +0200)]
igc: Fix the parameter description for igc_alloc_rx_buffers
The function description for igc_alloc_rx_buffers has not reflected
the function meaning. Add meaningful description.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Sasha Neftin [Sun, 10 Nov 2019 15:57:44 +0000 (17:57 +0200)]
igc: Remove excess parameter description from igc_is_non_eop
The function description for igc_is_non_eop includes an extra @skb
parameter description. This parameter doesn't exist on the function, so
remove it.
Suggested-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Sasha Neftin [Sun, 10 Nov 2019 14:05:20 +0000 (16:05 +0200)]
igc: Prefer to use the pci_release_mem_regions method
Use the pci_release_mem_regions method instead of the
pci_release_selected_regions method
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Sasha Neftin [Tue, 5 Nov 2019 09:44:13 +0000 (11:44 +0200)]
igc: Improve the DMA mapping flow
Improve the probe flow and set both the DMA mask and the coherent
to the same thing. Make the flow optimized and cleared.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Sasha Neftin [Thu, 31 Oct 2019 06:06:07 +0000 (08:06 +0200)]
igc: Add scatter gather support
Scatter gather is used to do DMA data transfers of data that is written to
noncontiguous areas of memory.
This patch enables scatter gather support.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Robert Beckett [Tue, 22 Oct 2019 15:31:41 +0000 (16:31 +0100)]
igb: dont drop packets if rx flow control is enabled
If Rx flow control has been enabled (via autoneg or forced), packets
should not be dropped due to Rx descriptor ring exhaustion. Instead
pause frames should be used to apply back pressure. This only applies
if VFs are not in use.
Move SRRCTL setup to its own function for easy reuse and only set drop
enable bit if Rx flow control is not enabled.
Since v1: always enable dropping of packets if VFs in use.
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Linus Torvalds [Tue, 31 Dec 2019 19:14:58 +0000 (11:14 -0800)]
Merge git://git./linux/kernel/git/netdev/net
Pull networking fixes from David Miller:
1) Fix big endian overflow in nf_flow_table, from Arnd Bergmann.
2) Fix port selection on big endian in nft_tproxy, from Phil Sutter.
3) Fix precision tracking for unbound scalars in bpf verifier, from
Daniel Borkmann.
4) Fix integer overflow in socket rcvbuf check in UDP, from Antonio
Messina.
5) Do not perform a neigh confirmation during a pmtu update over a
tunnel, from Hangbin Liu.
6) Fix DMA mapping leak in dpaa_eth driver, from Madalin Bucur.
7) Various PTP fixes for sja1105 dsa driver, from Vladimir Oltean.
8) Add missing to dummy definition of of_mdiobus_child_is_phy(), from
Geert Uytterhoeven
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (54 commits)
hsr: fix slab-out-of-bounds Read in hsr_debugfs_rename()
net/sched: add delete_empty() to filters and use it in cls_flower
tcp: Fix highest_sack and highest_sack_seq
ptp: fix the race between the release of ptp_clock and cdev
net: dsa: sja1105: Reconcile the meaning of TPID and TPID2 for E/T and P/Q/R/S
Documentation: net: dsa: sja1105: Remove text about taprio base-time limitation
net: dsa: sja1105: Remove restriction of zero base-time for taprio offload
net: dsa: sja1105: Really make the PTP command read-write
net: dsa: sja1105: Take PTP egress timestamp by port, not mgmt slot
cxgb4/cxgb4vf: fix flow control display for auto negotiation
mlxsw: spectrum: Use dedicated policer for VRRP packets
mlxsw: spectrum_router: Skip loopback RIFs during MAC validation
net: stmmac: dwmac-meson8b: Fix the RGMII TX delay on Meson8b/8m2 SoCs
net/sched: act_mirred: Pull mac prior redir to non mac_header_xmit device
net_sched: sch_fq: properly set sk->sk_pacing_status
bnx2x: Fix accounting of vlan resources among the PFs
bnx2x: Use appropriate define for vlan credit
of: mdio: Add missing inline to of_mdiobus_child_is_phy() dummy
net: phy: aquantia: add suspend / resume ops for AQR105
dpaa_eth: fix DMA mapping leak
...
Linus Torvalds [Tue, 31 Dec 2019 18:51:27 +0000 (10:51 -0800)]
Merge tag 'tomoyo-fixes-for-5.5' of git://git.osdn.net/gitroot/tomoyo/tomoyo-test1
Pull tomoyo fixes from Tetsuo Handa:
"Two bug fixes:
- Suppress RCU warning at list_for_each_entry_rcu()
- Don't use fancy names on sockets"
* tag 'tomoyo-fixes-for-5.5' of git://git.osdn.net/gitroot/tomoyo/tomoyo-test1:
tomoyo: Suppress RCU warning at list_for_each_entry_rcu().
tomoyo: Don't use nifty names on sockets.
Taehee Yoo [Sat, 28 Dec 2019 16:28:09 +0000 (16:28 +0000)]
hsr: fix slab-out-of-bounds Read in hsr_debugfs_rename()
hsr slave interfaces don't have debugfs directory.
So, hsr_debugfs_rename() shouldn't be called when hsr slave interface name
is changed.
Test commands:
ip link add dummy0 type dummy
ip link add dummy1 type dummy
ip link add hsr0 type hsr slave1 dummy0 slave2 dummy1
ip link set dummy0 name ap
Splat looks like:
[21071.899367][T22666] ap: renamed from dummy0
[21071.914005][T22666] ==================================================================
[21071.919008][T22666] BUG: KASAN: slab-out-of-bounds in hsr_debugfs_rename+0xaa/0xb0 [hsr]
[21071.923640][T22666] Read of size 8 at addr
ffff88805febcd98 by task ip/22666
[21071.926941][T22666]
[21071.927750][T22666] CPU: 0 PID: 22666 Comm: ip Not tainted 5.5.0-rc2+ #240
[21071.929919][T22666] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[21071.935094][T22666] Call Trace:
[21071.935867][T22666] dump_stack+0x96/0xdb
[21071.936687][T22666] ? hsr_debugfs_rename+0xaa/0xb0 [hsr]
[21071.937774][T22666] print_address_description.constprop.5+0x1be/0x360
[21071.939019][T22666] ? hsr_debugfs_rename+0xaa/0xb0 [hsr]
[21071.940081][T22666] ? hsr_debugfs_rename+0xaa/0xb0 [hsr]
[21071.940949][T22666] __kasan_report+0x12a/0x16f
[21071.941758][T22666] ? hsr_debugfs_rename+0xaa/0xb0 [hsr]
[21071.942674][T22666] kasan_report+0xe/0x20
[21071.943325][T22666] hsr_debugfs_rename+0xaa/0xb0 [hsr]
[21071.944187][T22666] hsr_netdev_notify+0x1fe/0x9b0 [hsr]
[21071.945052][T22666] ? __module_text_address+0x13/0x140
[21071.945897][T22666] notifier_call_chain+0x90/0x160
[21071.946743][T22666] dev_change_name+0x419/0x840
[21071.947496][T22666] ? __read_once_size_nocheck.constprop.6+0x10/0x10
[21071.948600][T22666] ? netdev_adjacent_rename_links+0x280/0x280
[21071.949577][T22666] ? __read_once_size_nocheck.constprop.6+0x10/0x10
[21071.950672][T22666] ? lock_downgrade+0x6e0/0x6e0
[21071.951345][T22666] ? do_setlink+0x811/0x2ef0
[21071.951991][T22666] do_setlink+0x811/0x2ef0
[21071.952613][T22666] ? is_bpf_text_address+0x81/0xe0
[ ... ]
Reported-by: syzbot+9328206518f08318a5fd@syzkaller.appspotmail.com
Fixes:
4c2d5e33dcd3 ("hsr: rename debugfs file when interface name is changed")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Davide Caratti [Sat, 28 Dec 2019 15:36:58 +0000 (16:36 +0100)]
net/sched: add delete_empty() to filters and use it in cls_flower
Revert "net/sched: cls_u32: fix refcount leak in the error path of
u32_change()", and fix the u32 refcount leak in a more generic way that
preserves the semantic of rule dumping.
On tc filters that don't support lockless insertion/removal, there is no
need to guard against concurrent insertion when a removal is in progress.
Therefore, for most of them we can avoid a full walk() when deleting, and
just decrease the refcount, like it was done on older Linux kernels.
This fixes situations where walk() was wrongly detecting a non-empty
filter, like it happened with cls_u32 in the error path of change(), thus
leading to failures in the following tdc selftests:
6aa7: (filter, u32) Add/Replace u32 with source match and invalid indev
6658: (filter, u32) Add/Replace u32 with custom hash table and invalid handle
74c2: (filter, u32) Add/Replace u32 filter with invalid hash table id
On cls_flower, and on (future) lockless filters, this check is necessary:
move all the check_empty() logic in a callback so that each filter
can have its own implementation. For cls_flower, it's sufficient to check
if no IDRs have been allocated.
This reverts commit
275c44aa194b7159d1191817b20e076f55f0e620.
Changes since v1:
- document the need for delete_empty() when TCF_PROTO_OPS_DOIT_UNLOCKED
is used, thanks to Vlad Buslov
- implement delete_empty() without doing fl_walk(), thanks to Vlad Buslov
- squash revert and new fix in a single patch, to be nice with bisect
tests that run tdc on u32 filter, thanks to Dave Miller
Fixes:
275c44aa194b ("net/sched: cls_u32: fix refcount leak in the error path of u32_change()")
Fixes:
6676d5e416ee ("net: sched: set dedicated tcf_walker flag when tp is empty")
Suggested-by: Jamal Hadi Salim <jhs@mojatatu.com>
Suggested-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Reviewed-by: Vlad Buslov <vladbu@mellanox.com>
Tested-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vijay Khemka [Fri, 27 Dec 2019 22:43:49 +0000 (14:43 -0800)]
net/ncsi: Fix gma flag setting after response
gma_flag was set at the time of GMA command request but it should
only be set after getting successful response. Movinng this flag
setting in GMA response handler.
This flag is used mainly for not repeating GMA command once
received MAC address.
Signed-off-by: Vijay Khemka <vijaykhemka@fb.com>
Reviewed-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kevin Kou [Fri, 27 Dec 2019 13:11:16 +0000 (13:11 +0000)]
sctp: add enabled check for path tracepoint loop.
sctp_outq_sack is the main function handles SACK, it is called very
frequently. As the commit "move trace_sctp_probe_path into sctp_outq_sack"
added below code to this function, sctp tracepoint is disabled most of time,
but the loop of transport list will be always called even though the
tracepoint is disabled, this is unnecessary.
+ /* SCTP path tracepoint for congestion control debugging. */
+ list_for_each_entry(transport, transport_list, transports) {
+ trace_sctp_probe_path(transport, asoc);
+ }
This patch is to add tracepoint enabled check at outside of the loop of
transport list, and avoid traversing the loop when trace is disabled,
it is a small optimization.
Signed-off-by: Kevin Kou <qdkevin.kou@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 31 Dec 2019 04:31:41 +0000 (20:31 -0800)]
Merge branch 'Improvements-to-SJA1105-DSA-RX-timestamping'
Vladimir Oltean says:
====================
Improvements to SJA1105 DSA RX timestamping
This series makes the sja1105 DSA driver use a dedicated kernel thread
for RX timestamping, a process which is time-sensitive and otherwise a
bit fragile. This allows users to customize their system (probabil an
embedded PTP switch) fully and allocate the CPU bandwidth for the driver
to expedite the RX timestamps as quickly as possible.
While doing this conversion, add a function to the PTP core for
cancelling this kernel thread (function which I found rather strange to
be missing).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Fri, 27 Dec 2019 13:02:30 +0000 (15:02 +0200)]
net: dsa: sja1105: Empty the RX timestamping queue on PTP settings change
When disabling PTP timestamping, don't reset the switch with the new
static config until all existing PTP frames have been timestamped on the
RX path or dropped. There's nothing we can do with these afterwards.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Fri, 27 Dec 2019 13:02:29 +0000 (15:02 +0200)]
net: dsa: sja1105: Use PTP core's dedicated kernel thread for RX timestamping
And move the queue of skb's waiting for RX timestamps into the ptp_data
structure, since it isn't needed if PTP is not compiled.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Fri, 27 Dec 2019 13:02:28 +0000 (15:02 +0200)]
ptp: introduce ptp_cancel_worker_sync
In order to effectively use the PTP kernel thread for tasks such as
timestamping packets, allow the user control over stopping it, which is
needed e.g. when the timestamping queues must be drained.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cambda Zhu [Fri, 27 Dec 2019 08:52:37 +0000 (16:52 +0800)]
tcp: Fix highest_sack and highest_sack_seq
>From commit
50895b9de1d3 ("tcp: highest_sack fix"), the logic about
setting tp->highest_sack to the head of the send queue was removed.
Of course the logic is error prone, but it is logical. Before we
remove the pointer to the highest sack skb and use the seq instead,
we need to set tp->highest_sack to NULL when there is no skb after
the last sack, and then replace NULL with the real skb when new skb
inserted into the rtx queue, because the NULL means the highest sack
seq is tp->snd_nxt. If tp->highest_sack is NULL and new data sent,
the next ACK with sack option will increase tp->reordering unexpectedly.
This patch sets tp->highest_sack to the tail of the rtx queue if
it's NULL and new data is sent. The patch keeps the rule that the
highest_sack can only be maintained by sack processing, except for
this only case.
Fixes:
50895b9de1d3 ("tcp: highest_sack fix")
Signed-off-by: Cambda Zhu <cambda@linux.alibaba.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladis Dronov [Fri, 27 Dec 2019 02:26:27 +0000 (03:26 +0100)]
ptp: fix the race between the release of ptp_clock and cdev
In a case when a ptp chardev (like /dev/ptp0) is open but an underlying
device is removed, closing this file leads to a race. This reproduces
easily in a kvm virtual machine:
ts# cat openptp0.c
int main() { ... fp = fopen("/dev/ptp0", "r"); ... sleep(10); }
ts# uname -r
5.5.0-rc3-
46cf053e
ts# cat /proc/cmdline
... slub_debug=FZP
ts# modprobe ptp_kvm
ts# ./openptp0 &
[1] 670
opened /dev/ptp0, sleeping 10s...
ts# rmmod ptp_kvm
ts# ls /dev/ptp*
ls: cannot access '/dev/ptp*': No such file or directory
ts# ...woken up
[ 48.010809] general protection fault: 0000 [#1] SMP
[ 48.012502] CPU: 6 PID: 658 Comm: openptp0 Not tainted 5.5.0-rc3-
46cf053e #25
[ 48.014624] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), ...
[ 48.016270] RIP: 0010:module_put.part.0+0x7/0x80
[ 48.017939] RSP: 0018:
ffffb3850073be00 EFLAGS:
00010202
[ 48.018339] RAX:
000000006b6b6b6b RBX:
6b6b6b6b6b6b6b6b RCX:
ffff89a476c00ad0
[ 48.018936] RDX:
fffff65a08d3ea08 RSI:
0000000000000247 RDI:
6b6b6b6b6b6b6b6b
[ 48.019470] ... ^^^ a slub poison
[ 48.023854] Call Trace:
[ 48.024050] __fput+0x21f/0x240
[ 48.024288] task_work_run+0x79/0x90
[ 48.024555] do_exit+0x2af/0xab0
[ 48.024799] ? vfs_write+0x16a/0x190
[ 48.025082] do_group_exit+0x35/0x90
[ 48.025387] __x64_sys_exit_group+0xf/0x10
[ 48.025737] do_syscall_64+0x3d/0x130
[ 48.026056] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[ 48.026479] RIP: 0033:0x7f53b12082f6
[ 48.026792] ...
[ 48.030945] Modules linked in: ptp i6300esb watchdog [last unloaded: ptp_kvm]
[ 48.045001] Fixing recursive fault but reboot is needed!
This happens in:
static void __fput(struct file *file)
{ ...
if (file->f_op->release)
file->f_op->release(inode, file); <<< cdev is kfree'd here
if (unlikely(S_ISCHR(inode->i_mode) && inode->i_cdev != NULL &&
!(mode & FMODE_PATH))) {
cdev_put(inode->i_cdev); <<< cdev fields are accessed here
Namely:
__fput()
posix_clock_release()
kref_put(&clk->kref, delete_clock) <<< the last reference
delete_clock()
delete_ptp_clock()
kfree(ptp) <<< cdev is embedded in ptp
cdev_put
module_put(p->owner) <<< *p is kfree'd, bang!
Here cdev is embedded in posix_clock which is embedded in ptp_clock.
The race happens because ptp_clock's lifetime is controlled by two
refcounts: kref and cdev.kobj in posix_clock. This is wrong.
Make ptp_clock's sysfs device a parent of cdev with cdev_device_add()
created especially for such cases. This way the parent device with its
ptp_clock is not released until all references to the cdev are released.
This adds a requirement that an initialized but not exposed struct
device should be provided to posix_clock_register() by a caller instead
of a simple dev_t.
This approach was adopted from the commit
72139dfa2464 ("watchdog: Fix
the race between the release of watchdog_core_data and cdev"). See
details of the implementation in the commit
233ed09d7fda ("chardev: add
helper function to register char devs with a struct device").
Link: https://lore.kernel.org/linux-fsdevel/20191125125342.6189-1-vdronov@redhat.com/T/#u
Analyzed-by: Stephen Johnston <sjohnsto@redhat.com>
Analyzed-by: Vern Lovejoy <vlovejoy@redhat.com>
Signed-off-by: Vladis Dronov <vdronov@redhat.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Fri, 27 Dec 2019 01:11:13 +0000 (03:11 +0200)]
net: dsa: sja1105: Reconcile the meaning of TPID and TPID2 for E/T and P/Q/R/S
For first-generation switches (SJA1105E and SJA1105T):
- TPID means C-Tag (typically 0x8100)
- TPID2 means S-Tag (typically 0x88A8)
While for the second generation switches (SJA1105P, SJA1105Q, SJA1105R,
SJA1105S) it is the other way around:
- TPID means S-Tag (typically 0x88A8)
- TPID2 means C-Tag (typically 0x8100)
In other words, E/T tags untagged traffic with TPID, and P/Q/R/S with
TPID2.
So the patch mentioned below fixed VLAN filtering for P/Q/R/S, but broke
it for E/T.
We strive for a common code path for all switches in the family, so just
lie in the static config packing functions that TPID and TPID2 are at
swapped bit offsets than they actually are, for P/Q/R/S. This will make
both switches understand TPID to be ETH_P_8021Q and TPID2 to be
ETH_P_8021AD. The meaning from the original E/T was chosen over P/Q/R/S
because E/T is actually the one with public documentation available
(UM10944.pdf).
Fixes:
f9a1a7646c0d ("net: dsa: sja1105: Reverse TPID and TPID2")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Fri, 27 Dec 2019 01:08:07 +0000 (03:08 +0200)]
Documentation: net: dsa: sja1105: Remove text about taprio base-time limitation
Since commit
86db36a347b4 ("net: dsa: sja1105: Implement state machine
for TAS with PTP clock source"), this paragraph is no longer true. So
remove it.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Fri, 27 Dec 2019 01:03:54 +0000 (03:03 +0200)]
net: dsa: sja1105: Remove restriction of zero base-time for taprio offload
The check originates from the initial implementation which was not based
on PTP time but on a standalone clock source. In the meantime we can now
program the PTPSCHTM register at runtime with the dynamic base time
(actually with a value that is 200 ns smaller, to avoid writing DELTA=0
in the Schedule Entry Points Parameters Table). And we also have logic
for moving the actual base time in the future of the PHC's current time
base, so the check for zero serves no purpose, since even if the user
will specify zero, that's not what will end up in the static config
table where the limitation is.
Fixes:
86db36a347b4 ("net: dsa: sja1105: Implement state machine for TAS with PTP clock source")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Fri, 27 Dec 2019 01:01:50 +0000 (03:01 +0200)]
net: dsa: sja1105: Really make the PTP command read-write
When activating tc-taprio offload on the switch ports, the TAS state
machine will try to check whether it is running or not, but will find
both the STARTED and STOPPED bits as false in the
sja1105_tas_check_running function. So the function will return -EINVAL
(an abnormal situation) and the kernel will keep printing this from the
TAS FSM workqueue:
[ 37.691971] sja1105 spi0.1: An operation returned -22
The reason is that the underlying function that gets called,
sja1105_ptp_commit, does not actually do a SPI_READ, but a SPI_WRITE. So
the command buffer remains initialized with zeroes instead of retrieving
the hardware state. Fix that.
Fixes:
41603d78b362 ("net: dsa: sja1105: Make the PTP command read-write")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Fri, 27 Dec 2019 00:59:54 +0000 (02:59 +0200)]
net: dsa: sja1105: Take PTP egress timestamp by port, not mgmt slot
The PTP egress timestamp N must be captured from register PTPEGR_TS[n],
where n = 2 * PORT + TSREG. There are 10 PTPEGR_TS registers, 2 per
port. We are only using TSREG=0.
As opposed to the management slots, which are 4 in number
(SJA1105_NUM_PORTS, minus the CPU port). Any management frame (which
includes PTP frames) can be sent to any non-CPU port through any
management slot. When the CPU port is not the last port (#4), there will
be a mismatch between the slot and the port number.
Luckily, the only mainline occurrence with this switch
(arch/arm/boot/dts/ls1021a-tsn.dts) does have the CPU port as #4, so the
issue did not manifest itself thus far.
Fixes:
47ed985e97f5 ("net: dsa: sja1105: Add logic for TX timestamping")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Christophe JAILLET [Thu, 26 Dec 2019 15:02:24 +0000 (16:02 +0100)]
sfc: avoid duplicate error handling code in 'efx_ef10_sriov_set_vf_mac()'
'eth_zero_addr()' is already called in the error handling path. This is
harmless, but there is no point in calling it twice, so remove one.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 30 Dec 2019 14:06:19 +0000 (06:06 -0800)]
tcp_cubic: refactor code to perform a divide only when needed
Neal Cardwell suggested to not change ca->delay_min
and apply the ack delay cushion only when Hystart ACK train
is still under consideration. This should avoid a 64bit
divide unless needed.
Tested:
40Gbit(mlx4) testbed (with sch_fq as packet scheduler)
$ echo -n 'file tcp_cubic.c +p' >/sys/kernel/debug/dynamic_debug/control
$ nstat -n;for f in {1..10}; do ./super_netperf 1 -H lpaa24 -l -4000000; done;nstat|egrep "Hystart"
14815
16280
15293
15563
11574
15145
14789
18548
16972
12520
TcpExtTCPHystartTrainDetect 10 0.0
TcpExtTCPHystartTrainCwnd 1396 0.0
$ dmesg | tail -10
[ 4873.951350] hystart_ack_train (116 > 93) delay_min 24 (+ ack_delay 69) cwnd 80
[ 4875.155379] hystart_ack_train (55 > 50) delay_min 21 (+ ack_delay 29) cwnd 160
[ 4876.333921] hystart_ack_train (69 > 62) delay_min 23 (+ ack_delay 39) cwnd 130
[ 4877.519037] hystart_ack_train (69 > 60) delay_min 22 (+ ack_delay 38) cwnd 130
[ 4878.701559] hystart_ack_train (87 > 63) delay_min 24 (+ ack_delay 39) cwnd 160
[ 4879.844597] hystart_ack_train (93 > 50) delay_min 21 (+ ack_delay 29) cwnd 216
[ 4880.956650] hystart_ack_train (74 > 67) delay_min 20 (+ ack_delay 47) cwnd 108
[ 4882.098500] hystart_ack_train (61 > 57) delay_min 23 (+ ack_delay 34) cwnd 130
[ 4883.262056] hystart_ack_train (72 > 67) delay_min 21 (+ ack_delay 46) cwnd 130
[ 4884.418760] hystart_ack_train (74 > 67) delay_min 29 (+ ack_delay 38) cwnd 152
10Gbit(bnx2x) testbed (with sch_fq as packet scheduler)
$ echo -n 'file tcp_cubic.c +p' >/sys/kernel/debug/dynamic_debug/control
$ nstat -n;for f in {1..10}; do ./super_netperf 1 -H lpk52 -l -4000000; done;nstat|egrep "Hystart"
7050
7065
7100
6900
7202
7263
7189
6869
7463
7034
TcpExtTCPHystartTrainDetect 10 0.0
TcpExtTCPHystartTrainCwnd 3199 0.0
$ dmesg | tail -10
[ 176.920012] hystart_ack_train (161 > 141) delay_min 83 (+ ack_delay 58) cwnd 264
[ 179.144645] hystart_ack_train (164 > 159) delay_min 120 (+ ack_delay 39) cwnd 444
[ 181.354527] hystart_ack_train (214 > 168) delay_min 125 (+ ack_delay 43) cwnd 436
[ 183.539565] hystart_ack_train (170 > 147) delay_min 96 (+ ack_delay 51) cwnd 326
[ 185.727309] hystart_ack_train (177 > 160) delay_min 61 (+ ack_delay 99) cwnd 128
[ 187.947142] hystart_ack_train (184 > 167) delay_min 123 (+ ack_delay 44) cwnd 367
[ 190.166680] hystart_ack_train (230 > 153) delay_min 116 (+ ack_delay 37) cwnd 444
[ 192.327285] hystart_ack_train (210 > 206) delay_min 86 (+ ack_delay 120) cwnd 152
[ 194.511392] hystart_ack_train (173 > 151) delay_min 94 (+ ack_delay 57) cwnd 239
[ 196.736023] hystart_ack_train (149 > 146) delay_min 105 (+ ack_delay 41) cwnd 399
Fixes:
42f3a8aaae66 ("tcp_cubic: tweak Hystart detection for short RTT flows")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Neal Cardwell <ncardwell@google.com>
Link: https://www.spinics.net/lists/netdev/msg621886.html
Link: https://www.spinics.net/lists/netdev/msg621797.html
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rahul Lakkireddy [Mon, 30 Dec 2019 12:44:08 +0000 (18:14 +0530)]
cxgb4/cxgb4vf: fix flow control display for auto negotiation
As per 802.3-2005, Section Two, Annex 28B, Table 28B-2 [1], when
_only_ Rx pause is enabled, both symmetric and asymmetric pause
towards local device must be enabled. Also, firmware returns the local
device's flow control pause params as part of advertised capabilities
and negotiated params as part of current link attributes. So, fix up
ethtool's flow control pause params fetch logic to read from acaps,
instead of linkattr.
[1] https://standards.ieee.org/standard/802_3-2005.html
Fixes:
c3168cabe1af ("cxgb4/cxgbvf: Handle 32-bit fw port capabilities")
Signed-off-by: Surendra Mobiya <surendra@chelsio.com>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 30 Dec 2019 22:22:11 +0000 (14:22 -0800)]
Merge git://git./linux/kernel/git/pablo/nf-next
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for net-next:
1) Remove #ifdef pollution around nf_ingress(), from Lukas Wunner.
2) Document ingress hook in netdevice, also from Lukas.
3) Remove htons() in tunnel metadata port netlink attributes,
from Xin Long.
4) Missing erspan netlink attribute validation also from Xin Long.
5) Missing erspan version in tunnel, from Xin Long.
6) Missing attribute nest in NFTA_TUNNEL_KEY_OPTS_{VXLAN,ERSPAN}
Patch from Xin Long.
7) Missing nla_nest_cancel() in tunnel netlink dump path,
from Xin Long.
8) Remove two exported conntrack symbols with no clients,
from Florian Westphal.
9) Add nft_meta_get_eval_time() helper to nft_meta, from Florian.
10) Add nft_meta_pkttype helper for loopback, also from Florian.
11) Add nft_meta_socket uid helper, from Florian Westphal.
12) Add nft_meta_cgroup helper, from Florian.
13) Add nft_meta_ifkind helper, from Florian.
14) Group all interface related meta selector, from Florian.
15) Add nft_prandom_u32() helper, from Florian.
16) Add nft_meta_rtclassid helper, from Florian.
17) Add support for matching on the slave device index,
from Florian.
This batch, among other things, contains updates for the netfilter
tunnel netlink interface: This extension is still incomplete and lacking
proper userspace support which is actually my fault, I did not find the
time to go back and finish this. This update is breaking tunnel UAPI in
some aspects to fix it but do it better sooner than never.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sun, 29 Dec 2019 23:29:16 +0000 (15:29 -0800)]
Linux 5.5-rc4
David S. Miller [Sun, 29 Dec 2019 20:29:14 +0000 (12:29 -0800)]
Merge branch 'mlxsw-fixes'
Ido Schimmel says:
====================
mlxsw: Couple of fixes
This patch set contains two fixes for mlxsw. Please consider both for
stable.
Patch #1 from Amit fixes a wrong check during MAC validation when
creating router interfaces (RIFs). Given a particular order of
configuration this can result in the driver refusing to create new RIFs.
Patch #2 fixes a wrong trap configuration in which VRRP packets and
routing exceptions were policed by the same policer towards the CPU. In
certain situations this can prevent VRRP packets from reaching the CPU.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Sun, 29 Dec 2019 11:40:23 +0000 (13:40 +0200)]
mlxsw: spectrum: Use dedicated policer for VRRP packets
Currently, VRRP packets and packets that hit exceptions during routing
(e.g., MTU error) are policed using the same policer towards the CPU.
This means, for example, that misconfiguration of the MTU on a routed
interface can prevent VRRP packets from reaching the CPU, which in turn
can cause the VRRP daemon to assume it is the Master router.
Fix this by using a dedicated policer for VRRP packets.
Fixes:
11566d34f895 ("mlxsw: spectrum: Add VRRP traps")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Alex Veber <alexve@mellanox.com>
Tested-by: Alex Veber <alexve@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Amit Cohen [Sun, 29 Dec 2019 11:40:22 +0000 (13:40 +0200)]
mlxsw: spectrum_router: Skip loopback RIFs during MAC validation
When a router interface (RIF) is created the MAC address of the backing
netdev is verified to have the same MSBs as existing RIFs. This is
required in order to avoid changing existing RIF MAC addresses that all
share the same MSBs.
Loopback RIFs are special in this regard as they do not have a MAC
address, given they are only used to loop packets from the overlay to
the underlay.
Without this change, an error is returned when trying to create a RIF
after the creation of a GRE tunnel that is represented by a loopback
RIF. 'rif->dev->dev_addr' points to the GRE device's local IP, which
does not share the same MSBs as physical interfaces. Adding an IP
address to any physical interface results in:
Error: mlxsw_spectrum: All router interface MAC addresses must have the
same prefix.
Fix this by skipping loopback RIFs during MAC validation.
Fixes:
74bc99397438 ("mlxsw: spectrum_router: Veto unsupported RIF MAC addresses")
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sun, 29 Dec 2019 18:01:27 +0000 (10:01 -0800)]
Merge tag 'riscv/for-v5.5-rc4' of git://git./linux/kernel/git/riscv/linux
Pull RISC-V fixes from Paul Walmsley:
"One important fix for RISC-V:
- Redirect any incoming syscall with an ID less than -1 to
sys_ni_syscall, rather than allowing them to fall through into the
syscall handler.
and two minor build fixes:
- Export __asm_copy_{from,to}_user() from where they are defined.
This fixes a build error triggered by some randconfigs.
- Export flush_icache_all(). I'd resisted this before, since
historically we didn't want modules to be able to flush the I$
directly; but apparently everyone else is doing it now"
* tag 'riscv/for-v5.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: export flush_icache_all to modules
riscv: reject invalid syscalls below -1
riscv: fix compile failure with EXPORT_SYMBOL() & !MMU
Linus Torvalds [Sun, 29 Dec 2019 17:50:57 +0000 (09:50 -0800)]
Merge tag 'locks-v5.5-1' of git://git./linux/kernel/git/jlayton/linux
Pull /proc/locks formatting fix from Jeff Layton:
"This is a trivial fix for a _very_ long standing bug in /proc/locks
formatting. Ordinarily, I'd wait for the merge window for something
like this, but it is making it difficult to validate some overlayfs
fixes.
I've also gone ahead and marked this for stable"
* tag 'locks-v5.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/jlayton/linux:
locks: print unsigned ino in /proc/locks
Linus Torvalds [Sun, 29 Dec 2019 17:48:47 +0000 (09:48 -0800)]
Merge tag '5.5-rc3-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs fixes from Steve French:
"One performance fix for large directory searches, and one minor style
cleanup noticed by Clang"
* tag '5.5-rc3-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
cifs: Optimize readdir on reparse points
cifs: Adjust indentation in smb2_open_file
Amir Goldstein [Sun, 22 Dec 2019 18:45:28 +0000 (20:45 +0200)]
locks: print unsigned ino in /proc/locks
An ino is unsigned, so display it as such in /proc/locks.
Cc: stable@vger.kernel.org
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Jeff Layton <jlayton@kernel.org>
David S. Miller [Sat, 28 Dec 2019 19:43:41 +0000 (11:43 -0800)]
Merge branch 'DSA-TX-tstamp'
Vladimir Oltean says:
====================
The DSA TX timestamping situation
This series is the moral v2 of "[PATCH net] net: dsa: sja1105: Fix
double delivery of TX timestamps to socket error queue" [0] which did
not manage to convince public opinion (actually it didn't convince me
neither).
This fixes PTP timestamping on one particular board, where the DSA
switch is sja1105 and the master is gianfar. Unfortunately there is no
way to make the fix more general without committing logical
inaccuracies: the SKBTX_IN_PROGRESS flag does serve a purpose, even if
the sja1105 driver is not using it now: it prevents delivering a SW
timestamp to the app socket when the HW timestamp will be provided. So
not setting this flag (the approach from v1) might create avoidable
complications in the future (not to mention that there isn't any
satisfactory explanation on why that would be the correct solution).
So the goal of this change set is to create a more strict framework for
DSA master devices when attached to PTP switches, and to fix the first
master driver that is overstepping its duties and is delivering
unsolicited TX timestamps.
[0]: https://www.spinics.net/lists/netdev/msg619699.html
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Sat, 28 Dec 2019 13:30:46 +0000 (15:30 +0200)]
net: dsa: Deny PTP on master if switch supports it
It is possible to kill PTP on a DSA switch completely and absolutely,
until a reboot, with a simple command:
tcpdump -i eth2 -j adapter_unsynced
where eth2 is the switch's DSA master.
Why? Well, in short, the PTP API in place today is a bit rudimentary and
relies on applications to retrieve the TX timestamps by polling the
error queue and looking at the cmsg structure. But there is no timestamp
identification of any sorts (except whether it's HW or SW), you don't
know how many more timestamps are there to come, which one is this one,
from whom it is, etc. In other words, the SO_TIMESTAMPING API is
fundamentally limited in that you can get a single HW timestamp from the
stack.
And the "-j adapter_unsynced" flag of tcpdump enables hardware
timestamping.
So let's imagine what happens when the DSA master decides it wants to
deliver TX timestamps to the skb's socket too:
- The timestamp that the user space sees is taken by the DSA master.
Whereas the RX timestamp will eventually be overwritten by the DSA
switch. So the RX and TX timestamps will be in different time bases
(aka garbage).
- The user space applications have no way to deal with the second (real)
TX timestamp finally delivered by the DSA switch, or even to know to
wait for it.
Take ptp4l from the linuxptp project, for example. This is its behavior
after running tcpdump, before the patch:
ptp4l[172]: [6469.594] Unexpected data on socket err queue:
ptp4l[172]: [6469.693] rms 8 max 16 freq -21257 +/- 11 delay 748 +/- 0
ptp4l[172]: [6469.711] Unexpected data on socket err queue:
ptp4l[172]: 0020 00 00 00 1f 7b ff fe 63 02 48 00 03 aa 05 00 fd
ptp4l[172]: 0030 00 00 00 00 00 00 00 00 00 00
ptp4l[172]: [6469.721] Unexpected data on socket err queue:
ptp4l[172]: 0000 01 80 c2 00 00 0e 00 1f 7b 63 02 48 88 f7 10 02
ptp4l[172]: 0010 00 2c 00 00 02 00 00 00 00 00 00 00 00 00 00 00
ptp4l[172]: 0020 00 00 00 1f 7b ff fe 63 02 48 00 01 c6 b1 00 fd
ptp4l[172]: 0030 00 00 00 00 00 00 00 00 00 00
ptp4l[172]: [6469.838] Unexpected data on socket err queue:
ptp4l[172]: 0000 01 80 c2 00 00 0e 00 1f 7b 63 02 48 88 f7 10 02
ptp4l[172]: 0010 00 2c 00 00 02 00 00 00 00 00 00 00 00 00 00 00
ptp4l[172]: 0020 00 00 00 1f 7b ff fe 63 02 48 00 03 aa 06 00 fd
ptp4l[172]: 0030 00 00 00 00 00 00 00 00 00 00
ptp4l[172]: [6469.848] Unexpected data on socket err queue:
ptp4l[172]: 0000 01 80 c2 00 00 0e 00 1f 7b 63 02 48 88 f7 13 02
ptp4l[172]: 0010 00 36 00 00 02 00 00 00 00 00 00 00 00 00 00 00
ptp4l[172]: 0020 00 00 00 1f 7b ff fe 63 02 48 00 04 1a 45 05 7f
ptp4l[172]: 0030 00 00 5e 05 41 32 27 c2 1a 68 00 04 9f ff fe 05
ptp4l[172]: 0040 de 06 00 01
ptp4l[172]: [6469.855] Unexpected data on socket err queue:
ptp4l[172]: 0000 01 80 c2 00 00 0e 00 1f 7b 63 02 48 88 f7 10 02
ptp4l[172]: 0010 00 2c 00 00 02 00 00 00 00 00 00 00 00 00 00 00
ptp4l[172]: 0020 00 00 00 1f 7b ff fe 63 02 48 00 01 c6 b2 00 fd
ptp4l[172]: 0030 00 00 00 00 00 00 00 00 00 00
ptp4l[172]: [6469.974] Unexpected data on socket err queue:
ptp4l[172]: 0000 01 80 c2 00 00 0e 00 1f 7b 63 02 48 88 f7 10 02
ptp4l[172]: 0010 00 2c 00 00 02 00 00 00 00 00 00 00 00 00 00 00
ptp4l[172]: 0020 00 00 00 1f 7b ff fe 63 02 48 00 03 aa 07 00 fd
ptp4l[172]: 0030 00 00 00 00 00 00 00 00 00 00
The ptp4l program itself is heavily patched to show this (more details
here [0]). Otherwise, by default it just hangs.
On the other hand, with the DSA patch to disallow HW timestamping
applied:
tcpdump -i eth2 -j adapter_unsynced
tcpdump: SIOCSHWTSTAMP failed: Device or resource busy
So it is a fact of life that PTP timestamping on the DSA master is
incompatible with timestamping on the switch MAC, at least with the
current API. And if the switch supports PTP, taking the timestamps from
the switch MAC is highly preferable anyway, due to the fact that those
don't contain the queuing latencies of the switch. So just disallow PTP
on the DSA master if there is any PTP-capable switch attached.
[0]: https://sourceforge.net/p/linuxptp/mailman/message/
36880648/
Fixes:
0336369d3a4d ("net: dsa: forward hardware timestamping ioctls to switch driver")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Sat, 28 Dec 2019 13:30:45 +0000 (15:30 +0200)]
gianfar: Fix TX timestamping with a stacked DSA driver
The driver wrongly assumes that it is the only entity that can set the
SKBTX_IN_PROGRESS bit of the current skb. Therefore, in the
gfar_clean_tx_ring function, where the TX timestamp is collected if
necessary, the aforementioned bit is used to discriminate whether or not
the TX timestamp should be delivered to the socket's error queue.
But a stacked driver such as a DSA switch can also set the
SKBTX_IN_PROGRESS bit, which is actually exactly what it should do in
order to denote that the hardware timestamping process is undergoing.
Therefore, gianfar would misinterpret the "in progress" bit as being its
own, and deliver a second skb clone in the socket's error queue,
completely throwing off a PTP process which is not expecting to receive
it, _even though_ TX timestamping is not enabled for gianfar.
There have been discussions [0] as to whether non-MAC drivers need or
not to set SKBTX_IN_PROGRESS at all (whose purpose is to avoid sending 2
timestamps, a sw and a hw one, to applications which only expect one).
But as of this patch, there are at least 2 PTP drivers that would break
in conjunction with gianfar: the sja1105 DSA switch and the felix
switch, by way of its ocelot core driver.
So regardless of that conclusion, fix the gianfar driver to not do stuff
based on flags set by others and not intended for it.
[0]: https://www.spinics.net/lists/netdev/msg619699.html
Fixes:
f0ee7acfcdd4 ("gianfar: Add hardware TX timestamping support")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Chen Zhou [Sat, 28 Dec 2019 03:09:47 +0000 (11:09 +0800)]
net/wan/fsl_ucc_hdlc: remove set but not used variables 'ut_info' and 'ret'
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wan/fsl_ucc_hdlc.c: In function ucc_hdlc_irq_handler:
drivers/net/wan/fsl_ucc_hdlc.c:643:23:
warning: variable ut_info set but not used [-Wunused-but-set-variable]
drivers/net/wan/fsl_ucc_hdlc.c: In function uhdlc_suspend:
drivers/net/wan/fsl_ucc_hdlc.c:880:23:
warning: variable ut_info set but not used [-Wunused-but-set-variable]
drivers/net/wan/fsl_ucc_hdlc.c: In function uhdlc_resume:
drivers/net/wan/fsl_ucc_hdlc.c:925:6:
warning: variable ret set but not used [-Wunused-but-set-variable]
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Chen Zhou <chenzhou10@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Olof Johansson [Tue, 17 Dec 2019 04:07:04 +0000 (20:07 -0800)]
riscv: export flush_icache_all to modules
This is needed by LKDTM (crash dump test module), it calls
flush_icache_range(), which on RISC-V turns into flush_icache_all(). On
other architectures, the actual implementation is exported, so follow
that precedence and export it here too.
Fixes build of CONFIG_LKDTM that fails with:
ERROR: "flush_icache_all" [drivers/misc/lkdtm/lkdtm.ko] undefined!
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
David Abdurachmanov [Wed, 18 Dec 2019 08:47:56 +0000 (10:47 +0200)]
riscv: reject invalid syscalls below -1
Running "stress-ng --enosys 4 -t 20 -v" showed a large number of kernel oops
with "Unable to handle kernel paging request at virtual address" message. This
happens when enosys stressor starts testing random non-valid syscalls.
I forgot to redirect any syscall below -1 to sys_ni_syscall.
With the patch kernel oops messages are gone while running stress-ng enosys
stressor.
Signed-off-by: David Abdurachmanov <david.abdurachmanov@sifive.com>
Fixes:
5340627e3fe0 ("riscv: add support for SECCOMP and SECCOMP_FILTER")
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>