arm64: dts: imx8mm-venice-gw72xx-0x: add dt overlay for imx219 rpi v2 camera

Add support for the RaspberryPi Camera v2 which is an IMX219 8MP module:
 - https://datasheets.raspberrypi.com/camera/camera-v2-schematics.pdf
 - has its own on-board 24MHz osc so no clock required from baseboard
 - pin 11 enables 1.8V and 2.8V LDO which is connected to
   GW73xx MIPI_GPIO4 (IMX8MM GPIO1_IO1) so we use this as a gpio

Support is added via a device-tree overlay.

The IMX219 supports RAW8/RAW10 image formats.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: imx8mm-venice-gw73xx-0x: add dt overlay for imx219 rpi v2 camera

Add support for the RaspberryPi Camera v2 which is an IMX219 8MP module:
 - https://datasheets.raspberrypi.com/camera/camera-v2-schematics.pdf
 - has its own on-board 24MHz osc so no clock required from baseboard
 - pin 11 enables 1.8V and 2.8V LDO which is connected to
   GW73xx MIPI_GPIO4 (IMX8MM GPIO1_IO1) so we use this as a gpio
   controlled regulator enable.

Support is added via a device-tree overlay.

The IMX219 supports RAW8/RAW10 image formats.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: imx8mm-venice-gw72xx-0x: add dt overlays for serial modes

The imx8mm-venice-gw72xx-0x som+baseboard combination has a multi-protocol
RS-232/RS-485/RS-422 transceiver to an off-board connector which
can be configured in a number of ways via UART and GPIO configuration.

The default configuration per the imx8mm-venice-gw72xx-0x dts is for
UART2 TX/RX and UART4 TX/RX to be available as RS-232:
 J15.1 UART2 TX out
 J15.2 UART2 RX in
 J15.3 UART4 TX out
 J15.4 UART4 RX in
 J15.5 GND

Add dt overlays to allow additional the modes of operation:

rs232-rts (UART2 RS-232 with RTS/CTS hardware flow control)
 J15.1 TX out
 J15.2 RX in
 J15.3 RTS out
 J15.4 CTS in
 J15.5 GND

rs485 (UART2 RS-485 half duplex)
 J15.1 TXRX-
 J15.2 N/C
 J15.3 TXRX+
 J15.4 N/C
 J15.5 GND

rs422 (UART2 RS-422 full duplex)
 J15.1 TX-
 J15.2 RX+
 J15.3 TX+
 J15.4 RX-
 J15.5 GND

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: imx8mm-venice-gw73xx-0x: add dt overlays for serial modes

The imx8mm-venice-gw73xx-0x som+baseboard combination has a multi-protocol
RS-232/RS-485/RS-422 transceiver to an off-board connector which
can be configured in a number of ways via UART and GPIO configuration.

The default configuration per the imx8mm-venice-gw73xx-0x dts is for
UART2 TX/RX and UART4 TX/RX to be available as RS-232:
 J15.1 UART2 TX out
 J15.2 UART2 RX in
 J15.3 UART4 TX out
 J15.4 UART4 RX in
 J15.5 GND

Add dt overlays to allow additional the modes of operation:

rs232-rts (UART2 RS-232 with RTS/CTS hardware flow control)
 J15.1 TX out
 J15.2 RX in
 J15.3 RTS out
 J15.4 CTS in
 J15.5 GND

rs485 (UART2 RS-485 half duplex)
 J15.1 TXRX-
 J15.2 N/C
 J15.3 TXRX+
 J15.4 N/C
 J15.5 GND

rs422 (UART2 RS-422 full duplex)
 J15.1 TX-
 J15.2 RX+
 J15.3 TX+
 J15.4 RX-
 J15.5 GND

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: imx: Add i.mx8mm Gateworks gw7903 dts support

The GW7903 is based on the i.MX 8M Mini SoC featuring:
 - LPDDR4 DRAM
 - eMMC FLASH
 - microSD connector with UHS support
 - LIS2DE12 3-axis accelerometer
 - Gateworks System Controller
 - IMX8M FEC
 - software selectable RS232/RS485/RS422 serial transceiver
 - PMIC
 - 2x off-board bi-directional opto-isolated digital I/O
 - 1x M.2 A-E Key Socket and 1x MiniPCIe socket with USB2.0 and PCIe
   (resistor loading to route PCIe/USB2 between M.2 and MiniPCIe socket)

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: ls1028a: add efuse node

Layerscape SoCs contain a Security Fuse Processor which is basically a
efuse controller. Add the node, so userspace can read the efuses.

Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: imx8mp-evk: add support for I2C5

Add support for i2c5, which is used to access the
external I2C bus on connector J22 of the imx8mp-evk.

Limit the speed to 100kHz since this is an external I2C bus.

Disabled by default, since it is shared with the CAN1 bus.

To enable i2c5, you need to disable the CAN1 function, enable the i2c5
function and also configure the CAN1/I2C5_SEL GPIO to HIGH to
select i2c5 instead of CAN1. This can be done by defining a gpio-hog
inside the pca6416 node, in your board device tree, like in this example:

&flexcan1 {
status = "disabled";
};

&i2c5 {
status = "okay";
};

&pca6416 {
can1-i2c5-sel-hog {
gpio-hog;
gpios = <2 GPIO_ACTIVE_HIGH>;
output-high;
line-name = "can1-i2c5-sel";
};
};

Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: imx8mp-evk: add PCA6416 gpio line names

Add gpio-line-names for the various GPIO's connected to the PCA6416
I/O expander on the imx8mp EVK.

This helps when using the new gpiod interface to find the GPIOs by name.

Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: imx8qm: added more serial alias to dts

Add more serial alias to imx8qm.dtsi file

Cc: Rob Herring <robh+dt@kernel.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Oliver Graute <oliver.graute@kococonnector.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: imx8qm: add compatible string for usdhc3

add compatible string for usdhc3

Cc: Rob Herring <robh+dt@kernel.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Oliver Graute <oliver.graute@kococonnector.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: imx8mq-evk: Add second PCIe port support

Enable the second PCIe port support on i.MX8MQ EVK board.

Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: imx8mm-beacon: Enable PCIe

The baseboard supports a PCIe slot with a 100MHz reference clock,
but it's controlled by a different GPIO, so a gated clock is
required.

Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: freescale: add initial support for verdin imx8m mini

This patch adds the device tree to support Toradex Verdin iMX8M Mini a
computer on module which can be used on different carrier boards.

The module consists of an NXP i.MX 8M Mini family SoC (either i.MX 8M
Mini Quad or 8M Mini DualLite), a PCA9450A PMIC, a Gigabit Ethernet PHY,
1 or 2 GB of LPDDR4 RAM, an eMMC, a TLA2024 ADC, an I2C EEPROM, an
RX8130 RTC, an optional SPI CAN controller plus an optional Bluetooth/
Wi-Fi module.

Anything that is not self-contained on the module is disabled by
default.

The device tree for the Dahlia includes the module's device tree and
enables the supported peripherals of the carrier board.

The device tree for the Verdin Development Board includes the module's
device tree as well as the Dahlia one as it is a superset and supports
almost all peripherals available.

So far there is no display functionality supported at all but basic
console UART, PCIe, USB host, eMMC and Ethernet and PCIe functionality
work fine.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: imx8mp-evk: add PCA6416 interrupt controller mode

Add interrupt controller mode for the pca6416 on i.MX8MP EVK board's.

Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: freescale: Use overlay target for simplicity

With commit 15d16d6dadf6 ("kbuild: Add generic rule to apply
fdtoverlay"), overlay target can be used to simplify the build of DTB
overlays.  It also performs a cross check to ensure base DT and overlay
actually match.

Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>

arm64: dts: fsl-ls1028a-qds: Drop overlay syntax hard coding

As suggested by commit 9ae8578b517a ("of: Documentation: change overlay
example to use current syntax"), there is no need to have overlay syntax
be hard coded in the device tree source file any more.

Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>

arm64: dts: imx8mm: fix strange hex notation

Fix strange hex notation with mixed lower-case and upper-case letters.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: imx8mm: Add support for emtrion emCON-MX8M Mini

This patch adds support for the emtrion GmbH emCON-MX8M Mini modules.
They are available with NXP i.MX 8M Mini equipped with 2 or 4 GB Memory.

The devicetree imx8mm-emcon.dtsi is the common part providing all
module components and the basic support for the SoC. The support for the
avari baseboard in the developer-kit configuration is provided by the
emcon-avari dts files.

Signed-off-by: Reinhold Mueller <reinhold.mueller@emtrion.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: tqma8mqml: add PCIe support

Add PCIe support to TQMa8MxML series.

Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: imx8mm: Enable Hantro G1 and G2 video decoders

There are two decoders on the i.MX8M Mini controlled by the
vpu-blk-ctrl.  The G1 supports H264 and VP8 while the
G2 support HEVC and VP9.

Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: imx8mq: Enable both G1 and G2 VPU's with vpu-blk-ctrl

With the Hantro G1 and G2 now setup to run independently, update
the device tree to allow both to operate.  This requires the
vpu-blk-ctrl node to be configured.  Since vpu-blk-ctrl needs
certain clock enabled to handle the gating of the G1 and G2
fuses, the clock-parents and clock-rates for the various VPU's
to be moved into the pgc_vpu because they cannot get re-parented
once enabled, and the pgc_vpu is the highest in the chain.

Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Merge commit '7a7b1414ea9a3641672be768afe16f583f0b76e7' into imx/dt64

arm64: dts: imx8mq-tqma8mq: Remove redundant vpu reference

The vpu is enabled by default, so there is no need to manually
enable it.

Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: ls1028a-qds: define mdio slots for networking options

The ls1028a QDS board support different pluggable PHY cards.  Define the
nodes for these slots to be updated at boot time with overlay according
to board setup.

Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: imx8m{m,n}_venice*: add gpio-line-names

Add gpio-line-names for the various GPIO's used on Gateworks Venice
boards. Note that these GPIO's are typically 'configured' in Boot
Firmware via gpio-hog therefore we only configure line names to keep the
boot firmware configuration from changing on kernel init.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: imx8mn-venice-gw7902: disable gpu

Since commit 9a0f3b157e22 ("arm64: dts: imx8mn: Enable GPU")
imx8mn-venice-gw7902 will hang during kernel init because it uses
a MIMX8MN5CVTI which does not have a GPU.

Disable pgc_gpumix to work around this. We also disable the GPU devices
that depend on the gpumix power domain and pgc_gpu to avoid them staying
in a probe deferred state forever.

Cc: Adam Ford <aford173@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Fixes: 9a0f3b157e22 ("arm64: dts: imx8mn: Enable GPU")
Reviewed-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: imx8mm: Add missing MX8MM_IOMUXC_NAND_READY_B_SD3_RESET_B

The i.MX8M Mini Application Processor Reference Manual, Rev. 3, 11/2020
documents AF MX8MM_IOMUXC_NAND_READY_B_SD3_RESET_B , add it into the
pinmux tables.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: imx8mp: disable usb3_phy1

Like usb3_phy0 the default state of the usb3_phy1 should be disabled, so
it is only enabled on boards exposing this USB port.

Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: imx8qxp-ss-adma: Drop fsl,imx7ulp-lpuart comaptible

The driver differs from clocks point of view, so the i.MX8QXP
is not backwards compatible with i.MX7ULP.

Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: imx8: add mu5/6 node

Add mu5/6 for i.MX8QXP/QM, these two mu will be used for
communicating with general purpose Cortex-M4 cores.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: imx8qm: Add SCU RTC node

Add SCU RTC node to support SC RTC driver.

Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: mnt-reform2: correct i2c3 pad-ctrl

The slew rate and drive-strength of the i2c3 pads were much too
high. Bring them down to avoid signal quality issues.

Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: mnt-reform2: add internal display support

This adds support for the internal display of the Reform2 Laptop, which
is connected to the i.MX8MQ via a MIPI-DSI->eDP bridge chip. Clocking
is derived from a system PLL, which provides quite good rate matching
for the single supported display mode and keeps the video PLL free for
usage with the external display, which isn't supported yet.

Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: imx8mq: disable DDRC node by default

Without a OPP table or a downstream TF-A running on the system the DDRC will
fail to probe, as it has no means to scale the DRAM frequency in that case.
This however will block the bus scaling driver to come up and this in turn
prevents other devices that hook into the interconnect from probing.

If the DDRC is disabled, the interconnect driver will simply ignore it. As
most systems don't want to scale the DRAM frequency, disable the node by
default and only enable it on the systems that actually uses this
capability and provides a valid OPP table in the DT.

Signed-off-by: Lucas Stach <dev@lynxeye.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Reviewed-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: imx: add Protonic PRT8MM board

The Protonic PRT8MM is a low-cost agricultural Virtual Terminal. This
commit adds most of the board functionality sans the display output,
as the i.MX8MM display support isn't ready yet.

Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: imx8qm: Drop CPU 'arm,armv8' compatible

The CPU 'arm,armv8' compatible is only for s/w models, so remove it from
i.MX8QM CPU nodes.

Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: imx8mm-venice*: add PCIe support

Add PCIe support to GW71xx/GW72xx/GW73xx/GW7901/GW7902

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: imx8mn: Enable GPU

The i.MX8M-Nano features a GC7000. The Etnaviv driver detects it as:

    etnaviv-gpu 38000000.gpu: model: GC7000, revision: 6203

Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: imx8mn: add DISP blk-ctrl

Add the DT node for the DISP blk-ctrl. With this in place the
display/mipi power domains should be functional.

Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: imx8mn: put USB controller into power-domains

Now that we have support for the power domain controller on the i.MX8MN,
we can put the USB controller in the respective power domain to allow
it to power down the PHY when possible.

Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: imx8mn: add GPC node

Add the DT node for the GPC, including all the PGC power domains,
some of them are not fully functional yet, as they require interaction
with the blk-ctrls to properly power up/down the peripherals.

Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: imx8mm-evk: Add the pcie support on imx8mm evk board

Add the PCIe support on iMX8MM EVK boards.
And set the default reference clock mode.

Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Tim Harvey <tharvey@gateworks.com>
Tested-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: imx8mm: Add the pcie support

Add the PCIe support on i.MX8MM platforms.

Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Tim Harvey <tharvey@gateworks.com>
Tested-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: imx8mm: Add the pcie phy support

Add the PCIe PHY support on iMX8MM platforms.

Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Tim Harvey <tharvey@gateworks.com>
Tested-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

dt-bindings: power: imx8mq: add defines for VPU blk-ctrl domains

This adds the defines for the power domains provided by the VPU
blk-ctrl on the i.MX8MQ.

Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Linux 5.17-rc1

Merge tag 'perf-tools-for-v5.17-2022-01-22' of git://git./linux/kernel/git/acme/linux

Pull more perf tools updates from Arnaldo Carvalho de Melo:

 - Fix printing 'phys_addr' in 'perf script'.

 - Fix failure to add events with 'perf probe' in ppc64 due to not
   removing leading dot (ppc64 ABIv1).

 - Fix cpu_map__item() python binding building.

 - Support event alias in form foo-bar-baz, add pmu-events and
   parse-event tests for it.

 - No need to setup affinities when starting a workload or attaching to
   a pid.

 - Use path__join() to compose a path instead of ad-hoc snprintf()
   equivalent.

 - Override attr->sample_period for non-libpfm4 events.

 - Use libperf cpumap APIs instead of accessing the internal state
   directly.

 - Sync x86 arch prctl headers and files changed by the new
   set_mempolicy_home_node syscall with the kernel sources.

 - Remove duplicate include in cpumap.h.

 - Remove redundant err variable.

* tag 'perf-tools-for-v5.17-2022-01-22' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux:
  perf tools: Remove redundant err variable
  perf test: Add parse-events test for aliases with hyphens
  perf test: Add pmu-events test for aliases with hyphens
  perf parse-events: Support event alias in form foo-bar-baz
  perf evsel: Override attr->sample_period for non-libpfm4 events
  perf cpumap: Remove duplicate include in cpumap.h
  perf cpumap: Migrate to libperf cpumap api
  perf python: Fix cpu_map__item() building
  perf script: Fix printing 'phys_addr' failure issue
  tools headers UAPI: Sync files changed by new set_mempolicy_home_node syscall
  tools headers UAPI: Sync x86 arch prctl headers with the kernel sources
  perf machine: Use path__join() to compose a path instead of snprintf(dir, '/', filename)
  perf evlist: No need to setup affinities when disabling events for pid targets
  perf evlist: No need to setup affinities when enabling events for pid targets
  perf stat: No need to setup affinities when starting a workload
  perf affinity: Allow passing a NULL arg to affinity__cleanup()
  perf probe: Fix ppc64 'perf probe add events failed' case

Merge tag 'trace-v5.17-3' of git://git./linux/kernel/git/rostedt/linux-trace

Pull ftrace fix from Steven Rostedt:
 "Fix s390 breakage from sorting mcount tables.

  The latest merge of the tracing tree sorts the mcount table at build
  time. But s390 appears to do things differently (like always) and
  replaces the sorted table back to the original unsorted one. As the
  ftrace algorithm depends on it being sorted, bad things happen when it
  is not, and s390 experienced those bad things.

  Add a new config to tell the boot if the mcount table is sorted or
  not, and allow s390 to opt out of it"

* tag 'trace-v5.17-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  ftrace: Fix assuming build time sort works for s390

ftrace: Fix assuming build time sort works for s390

To speed up the boot process, as mcount_loc needs to be sorted for ftrace
to work properly, sorting it at build time is more efficient than boot up
and can save milliseconds of time. Unfortunately, this change broke s390
as it will modify the mcount_loc location after the sorting takes place
and will put back the unsorted locations. Since the sorting is skipped at
boot up if it is believed that it was sorted at run time, ftrace can crash
as its algorithms are dependent on the list being sorted.

Add a new config BUILDTIME_MCOUNT_SORT that is set when
BUILDTIME_TABLE_SORT but not if S390 is set. Use this config to determine
if sorting should take place at boot up.

Link: https://lore.kernel.org/all/yt9dee51ctfn.fsf@linux.ibm.com/
Fixes: 72b3942a173c ("scripts: ftrace - move the sort-processing in ftrace_init")
Reported-by: Sven Schnelle <svens@linux.ibm.com>
Tested-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>

Merge tag 'kbuild-fixes-v5.17' of git://git./linux/kernel/git/masahiroy/linux-kbuild

Pull Kbuild fixes from Masahiro Yamada:

 - Bring include/uapi/linux/nfc.h into the UAPI compile-test coverage

 - Revert the workaround of CONFIG_CC_IMPLICIT_FALLTHROUGH

 - Fix build errors in certs/Makefile

* tag 'kbuild-fixes-v5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
  certs: Fix build error when CONFIG_MODULE_SIG_KEY is empty
  certs: Fix build error when CONFIG_MODULE_SIG_KEY is PKCS#11 URI
  Revert "Makefile: Do not quote value for CONFIG_CC_IMPLICIT_FALLTHROUGH"
  usr/include/Makefile: add linux/nfc.h to the compile-test coverage

Merge tag 'bitmap-5.17-rc1' of git://github.com/norov/linux

Pull bitmap updates from Yury Norov:

 - introduce for_each_set_bitrange()

 - use find_first_*_bit() instead of find_next_*_bit() where possible

 - unify for_each_bit() macros

* tag 'bitmap-5.17-rc1' of git://github.com/norov/linux:
  vsprintf: rework bitmap_list_string
  lib: bitmap: add performance test for bitmap_print_to_pagebuf
  bitmap: unify find_bit operations
  mm/percpu: micro-optimize pcpu_is_populated()
  Replace for_each_*_bit_from() with for_each_*_bit() where appropriate
  find: micro-optimize for_each_{set,clear}_bit()
  include/linux: move for_each_bit() macros from bitops.h to find.h
  cpumask: replace cpumask_next_* with cpumask_first_* where appropriate
  tools: sync tools/bitmap with mother linux
  all: replace find_next{,_zero}_bit with find_first{,_zero}_bit where appropriate
  cpumask: use find_first_and_bit()
  lib: add find_first_and_bit()
  arch: remove GENERIC_FIND_FIRST_BIT entirely
  include: move find.h from asm_generic to linux
  bitops: move find_bit_*_le functions from le.h to find.h
  bitops: protect find_first_{,zero}_bit properly

perf tools: Remove redundant err variable

Return value from perf_event__process_tracing_data() directly instead
of taking this in another redundant variable.

Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Link: http://lore.kernel.org/lkml/20220112080109.666800-1-chi.minghao@zte.com.cn
Signed-off-by: CGEL ZTE <cgel.zte@gmail.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

perf test: Add parse-events test for aliases with hyphens

Add a test which allows us to test parsing an event alias with hyphens.

Since these events typically do not exist on most host systems, add the
alias to the fake pmu.

Function perf_pmu__test_parse_init() has terms added to match known test
aliases.

Signed-off-by: John Garry <john.garry@huawei.com>
Acked-by: Ian Rogers <irogers@google.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Kajol Jain <kjain@linux.ibm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Qi Liu <liuqi115@huawei.com>
Cc: Shaokun Zhang <zhangshaokun@hisilicon.com>
Cc: linuxarm@huawei.com
Link: https://lore.kernel.org/r/1642432215-234089-4-git-send-email-john.garry@huawei.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

perf test: Add pmu-events test for aliases with hyphens

Add a test for aliases with hyphens in the name to ensure that the
pmu-events tables are as expects. There should be no reason why these sort
of aliases would be treated differently, but no harm in checking.

Signed-off-by: John Garry <john.garry@huawei.com>
Acked-by: Ian Rogers <irogers@google.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Kajol Jain <kjain@linux.ibm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Qi Liu <liuqi115@huawei.com>
Cc: Shaokun Zhang <zhangshaokun@hisilicon.com>
Cc: linuxarm@huawei.com
Link: https://lore.kernel.org/r/1642432215-234089-3-git-send-email-john.garry@huawei.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

perf parse-events: Support event alias in form foo-bar-baz

Event aliasing for events whose name in the form foo-bar-baz is not
supported, while foo-bar, foo_bar_baz, and other combinations are, i.e.
two hyphens are not supported.

The HiSilicon D06 platform has events in such form:

  $ ./perf list sdir-home-migrate

  List of pre-defined events (to be used in -e):

  uncore hha:
    sdir-home-migrate
   [Unit: hisi_sccl,hha]

  $ sudo ./perf stat -e sdir-home-migrate
  event syntax error: 'sdir-home-migrate'
                          \___ parser error
  Run 'perf list' for a list of valid events

   Usage: perf stat [<options>] [<command>]

   -e, --event <event>event selector. use 'perf list' to list available events

To support, add an extra PMU event symbol type for "baz", and add a new
rule in the bison file.

Signed-off-by: John Garry <john.garry@huawei.com>
Acked-by: Ian Rogers <irogers@google.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Kajol Jain <kjain@linux.ibm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Qi Liu <liuqi115@huawei.com>
Cc: Shaokun Zhang <zhangshaokun@hisilicon.com>
Cc: linuxarm@huawei.com
Link: https://lore.kernel.org/r/1642432215-234089-2-git-send-email-john.garry@huawei.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

perf evsel: Override attr->sample_period for non-libpfm4 events

A previous patch preventing "attr->sample_period" values from being
overridden in pfm events changed a related behaviour in arm-spe.

Before said patch:

  perf record -c 10000 -e arm_spe_0// -- sleep 1

Would yield an SPE event with period=10000. After the patch, the period
in "-c 10000" was being ignored because the arm-spe code initializes
sample_period to a non-zero value.

This patch restores the previous behaviour for non-libpfm4 events.

Fixes: ae5dcc8abe31 (“perf record: Prevent override of attr->sample_period for libpfm4 events”)
Reported-by: Chase Conklin <chase.conklin@arm.com>
Signed-off-by: German Gomez <german.gomez@arm.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: John Fastabend <john.fastabend@gmail.com>
Cc: KP Singh <kpsingh@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Martin KaFai Lau <kafai@fb.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Song Liu <songliubraving@fb.com>
Cc: Stephane Eranian <eranian@google.com>
Cc: Yonghong Song <yhs@fb.com>
Cc: bpf@vger.kernel.org
Cc: netdev@vger.kernel.org
Link: http://lore.kernel.org/lkml/20220118144054.2541-1-german.gomez@arm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

perf cpumap: Remove duplicate include in cpumap.h

Remove all but the first include of stdbool.h from cpumap.h.

Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Lv Ruyi <lv.ruyi@zte.com.cn>
Acked-by: Ian Rogers <irogers@google.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: James Clark <james.clark@arm.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Link: https://lore.kernel.org/r/20220117083730.863200-1-lv.ruyi@zte.com.cn
Signed-off-by: CGEL ZTE <cgel.zte@gmail.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

perf cpumap: Migrate to libperf cpumap api

Switch from directly accessing the perf_cpu_map to using the appropriate
libperf API when possible. Using the API simplifies the job of
refactoring use of perf_cpu_map.

Signed-off-by: Ian Rogers <irogers@google.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Alexey Bayduraev <alexey.v.bayduraev@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: André Almeida <andrealmeid@collabora.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Darren Hart <dvhart@infradead.org>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Dmitriy Vyukov <dvyukov@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: German Gomez <german.gomez@arm.com>
Cc: James Clark <james.clark@arm.com>
Cc: Jin Yao <yao.jin@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: John Garry <john.garry@huawei.com>
Cc: Kajol Jain <kjain@linux.ibm.com>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Leo Yan <leo.yan@linaro.org>
Cc: Madhavan Srinivasan <maddy@linux.ibm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Miaoqian Lin <linmq006@gmail.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Riccardo Mancini <rickyman7@gmail.com>
Cc: Shunsuke Nakamura <nakamura.shun@fujitsu.com>
Cc: Song Liu <song@kernel.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Stephen Brennan <stephen.s.brennan@oracle.com>
Cc: Steven Rostedt (VMware) <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Thomas Richter <tmricht@linux.ibm.com>
Cc: Yury Norov <yury.norov@gmail.com>
Link: http://lore.kernel.org/lkml/20220122045811.3402706-3-irogers@google.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

perf python: Fix cpu_map__item() building

Value should be built as an integer.

Switch some uses of perf_cpu_map to use the library API.

Fixes: 6d18804b963b78dc ("perf cpumap: Give CPUs their own type")
Signed-off-by: Ian Rogers <irogers@google.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Alexey Bayduraev <alexey.v.bayduraev@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: André Almeida <andrealmeid@collabora.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Darren Hart <dvhart@infradead.org>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Dmitriy Vyukov <dvyukov@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: German Gomez <german.gomez@arm.com>
Cc: Ian Rogers <irogers@google.com>
Cc: James Clark <james.clark@arm.com>
Cc: Jin Yao <yao.jin@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: John Garry <john.garry@huawei.com>
Cc: Kajol Jain <kjain@linux.ibm.com>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Leo Yan <leo.yan@linaro.org>
Cc: Madhavan Srinivasan <maddy@linux.ibm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Miaoqian Lin <linmq006@gmail.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Riccardo Mancini <rickyman7@gmail.com>
Cc: Shunsuke Nakamura <nakamura.shun@fujitsu.com>
Cc: Song Liu <song@kernel.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Stephen Brennan <stephen.s.brennan@oracle.com>
Cc: Steven Rostedt (VMware) <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Thomas Richter <tmricht@linux.ibm.com>
Cc: Yury Norov <yury.norov@gmail.com>
Link: http://lore.kernel.org/lkml/20220122045811.3402706-2-irogers@google.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

perf script: Fix printing 'phys_addr' failure issue

Perf script was failed to print the phys_addr for SPE profiling.
One 'dummy' event is added by SPE profiling but it doesn't have PHYS_ADDR
attribute set, perf script then exits with error.

Now referring to 'addr', use evsel__do_check_stype() to check the type.

Before:

  # perf record -e arm_spe_0/branch_filter=0,ts_enable=1,pa_enable=1,load_filter=1,jitter=0,\
store_filter=0,min_latency=0,event_filter=2/ -p 4064384 -- sleep 3
  # perf script -F pid,tid,addr,phys_addr
  Samples for 'dummy:u' event do not have PHYS_ADDR attribute set. Cannot print 'phys_addr' field.

After:

  # perf record -e arm_spe_0/branch_filter=0,ts_enable=1,pa_enable=1,load_filter=1,jitter=0,\
store_filter=0,min_latency=0,event_filter=2/ -p 4064384 -- sleep 3
  # perf script -F pid,tid,addr,phys_addr
  4064384/4064384 ffff802f921be0d0      2f921be0d0
  4064384/4064384 ffff802f921be0d0      2f921be0d0

Reviewed-by: German Gomez <german.gomez@arm.com>
Signed-off-by: Yao Jin <jinyao5@huawei.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Hanjun Guo <guohanjun@huawei.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lore.kernel.org/lkml/20220121065954.2121900-1-liwei391@huawei.com
Signed-off-by: Wei Li <liwei391@huawei.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

certs: Fix build error when CONFIG_MODULE_SIG_KEY is empty

Since b8c96a6b466c ("certs: simplify $(srctree)/ handling and remove
config_filename macro"), when CONFIG_MODULE_SIG_KEY is empty,
signing_key.x509 fails to build:

    CERT    certs/signing_key.x509
  Usage: extract-cert <source> <dest>
  make[1]: *** [certs/Makefile:78: certs/signing_key.x509] Error 2
  make: *** [Makefile:1831: certs] Error 2

Pass "" to the first argument of extract-cert to fix the build error.

Link: https://lore.kernel.org/linux-kbuild/20220120094606.2skuyb26yjlnu66q@lion.mk-sys.cz/T/#u
Fixes: b8c96a6b466c ("certs: simplify $(srctree)/ handling and remove config_filename macro")
Reported-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Tested-by: Michal Kubecek <mkubecek@suse.cz>

certs: Fix build error when CONFIG_MODULE_SIG_KEY is PKCS#11 URI

When CONFIG_MODULE_SIG_KEY is PKCS#11 URL (pkcs11:*), signing_key.x509
fails to build:

  certs/Makefile:77: *** target pattern contains no '%'.  Stop.

Due to the typo, $(X509_DEP) contains a colon.

Fix it.

Fixes: b8c96a6b466c ("certs: simplify $(srctree)/ handling and remove config_filename macro")
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>

Revert "Makefile: Do not quote value for CONFIG_CC_IMPLICIT_FALLTHROUGH"

This reverts commit cd8c917a56f20f48748dd43d9ae3caff51d5b987.

Commit 129ab0d2d9f3 ("kbuild: do not quote string values in
include/config/auto.conf") provided the final solution.

Now reverting the temporary workaround.

Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>

usr/include/Makefile: add linux/nfc.h to the compile-test coverage

As linux/nfc.h userspace compilation was finally fixed by commits
79b69a83705e ("nfc: uapi: use kernel size_t to fix user-space builds")
and 7175f02c4e5f ("uapi: fix linux/nfc.h userspace compilation errors"),
there is no need to keep the compile-test exception for it in
usr/include/Makefile.

Signed-off-by: Dmitry V. Levin <ldv@altlinux.org>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>

Merge branch 'akpm' (patches from Andrew)

Merge yet more updates from Andrew Morton:
 "This is the post-linux-next queue. Material which was based on or
  dependent upon material which was in -next.

  69 patches.

  Subsystems affected by this patch series: mm (migration and zsmalloc),
  sysctl, proc, and lib"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (69 commits)
  mm: hide the FRONTSWAP Kconfig symbol
  frontswap: remove support for multiple ops
  mm: mark swap_lock and swap_active_head static
  frontswap: simplify frontswap_register_ops
  frontswap: remove frontswap_test
  mm: simplify try_to_unuse
  frontswap: remove the frontswap exports
  frontswap: simplify frontswap_init
  frontswap: remove frontswap_curr_pages
  frontswap: remove frontswap_shrink
  frontswap: remove frontswap_tmem_exclusive_gets
  frontswap: remove frontswap_writethrough
  mm: remove cleancache
  lib/stackdepot: always do filter_irq_stacks() in stack_depot_save()
  lib/stackdepot: allow optional init and stack_table allocation by kvmalloc()
  proc: remove PDE_DATA() completely
  fs: proc: store PDE()->data into inode->i_private
  zsmalloc: replace get_cpu_var with local_lock
  zsmalloc: replace per zpage lock with pool->migrate_lock
  locking/rwlocks: introduce write_lock_nested
  ...

Merge tag '5.17-rc-part2-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6

Pull cifs fixes from Steve French:

 - multichannel fixes, addressing additional reconnect and DFS scenarios

 - reenabling fscache support (indexing rewrite, metadata caching e.g.)

 - send additional version information during NTLMSSP negotiate to
   improve debugging

 - fix for a mount race

 - DFS fixes

 - fix for a memory leak for stable

* tag '5.17-rc-part2-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
  cifs: update internal module number
  smb3: send NTLMSSP version information
  cifs: Support fscache indexing rewrite
  cifs: cifs_ses_mark_for_reconnect should also update reconnect bits
  cifs: update tcpStatus during negotiate and sess setup
  cifs: make status checks in version independent callers
  cifs: remove repeated state change in dfs tree connect
  cifs: fix the cifs_reconnect path for DFS
  cifs: remove unused variable ses_selected
  cifs: protect all accesses to chan_* with chan_lock
  cifs: fix the connection state transitions with multichannel
  cifs: check reconnects for channels of active tcons too
  smb3: add new defines from protocol specification
  cifs: serialize all mount attempts
  cifs: quirk for STATUS_OBJECT_NAME_INVALID returned for non-ASCII dfs refs
  cifs: alloc_path_with_tree_prefix: do not append sep. if the path is empty
  cifs: clean up an inconsistent indenting
  cifs: free ntlmsspblob allocated in negotiate

Merge tag 'xfs-5.17-merge-7' of git://git./fs/xfs/xfs-linux

Pull xfs fixes from Darrick Wong:
 "One of the patches removes some dead code from xfs_ioctl32.h and the
  other fixes broken workqueue flushing in the inode garbage collector.

   - Minor cleanup of ioctl32 cruft

   - Clean up open coded inodegc workqueue function calls"

* tag 'xfs-5.17-merge-7' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
  xfs: flush inodegc workqueue tasks before cancel
  xfs: remove unused xfs_ioctl32.h declarations

Merge tag 'fscache-fixes-20220121' of git://git./linux/kernel/git/dhowells/linux-fs

Pull more fscache updates from David Howells:
 "A set of fixes and minor updates for the fscache rewrite:

   - Fix mishandling of volume collisions (the wait condition is
     inverted and so it was only waiting if the volume collision was
     already resolved).

   - Fix miscalculation of whether there's space available in
     cachefiles.

   - Make sure a default cache name is set on a cache if the user hasn't
     set one by the time they bind the cache.

   - Adjust the way the backing inode is presented in tracepoints, add a
     tracepoint for mkdir and trace directory lookup.

   - Add a tracepoint for failure to set the active file mark.

   - Add an explanation of the checks made on the backing filesystem.

   - Check that the backing filesystem supports tmpfile.

   - Document how the page-release cancellation of the read-skip
     optimisation works.

  And I've included a change for netfslib:

   - Make ops->init_rreq() optional"

* tag 'fscache-fixes-20220121' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs:
  netfs: Make ops->init_rreq() optional
  fscache: Add a comment explaining how page-release optimisation works
  cachefiles: Check that the backing filesystem supports tmpfiles
  cachefiles: Explain checks in a comment
  cachefiles: Trace active-mark failure
  cachefiles: Make some tracepoint adjustments
  cachefiles: set default tag name if it's unspecified
  cachefiles: Calculate the blockshift in terms of bytes, not pages
  fscache: Fix the volume collision wait condition

Merge tag 'folio-5.17a' of git://git.infradead.org/users/willy/pagecache

Pull more folio updates from Matthew Wilcox:
 "Three small folio patches.

  One bug fix, one patch pulled forward from the patches destined for
  5.18 and then a patch to make use of that functionality"

* tag 'folio-5.17a' of git://git.infradead.org/users/willy/pagecache:
  filemap: Use folio_put_refs() in filemap_free_folio()
  mm: Add folio_put_refs()
  pagevec: Initialise folio_batch->percpu_pvec_drained

Merge tag 'scsi-misc' of git://git./linux/kernel/git/jejb/scsi

Pull more SCSI updates from James Bottomley:
 "This series is all the stragglers that didn't quite make the first
  merge window pull. It's mostly minor updates and bug fixes of merge
  window code"

* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: nsp_cs: Check of ioremap return value
  scsi: ufs: ufs-mediatek: Fix error checking in ufs_mtk_init_va09_pwr_ctrl()
  scsi: ufs: Modify Tactive time setting conditions
  scsi: efct: Remove useless DMA-32 fallback configuration
  scsi: message: fusion: mptctl: Use dma_alloc_coherent()
  scsi: message: fusion: mptsas: Use dma_alloc_coherent()
  scsi: message: fusion: Use dma_alloc_coherent() in mptsas_exp_repmanufacture_info()
  scsi: message: fusion: mptbase: Use dma_alloc_coherent()
  scsi: message: fusion: Use dma_alloc_coherent() in mpt_alloc_fw_memory()
  scsi: message: fusion: Remove usage of the deprecated "pci-dma-compat.h" API
  scsi: megaraid: Avoid mismatched storage type sizes
  scsi: hisi_sas: Remove unused variable and check in hisi_sas_send_ata_reset_each_phy()
  scsi: aic79xx: Remove redundant error variable
  scsi: pm80xx: Port reset timeout error handling correction
  scsi: mpi3mr: Fix formatting problems in some kernel-doc comments
  scsi: mpi3mr: Fix some spelling mistakes
  scsi: mpt3sas: Update persistent trigger pages from sysfs interface
  scsi: core: Fix scsi_mode_select() interface
  scsi: aacraid: Fix spelling of "its"
  scsi: qedf: Fix potential dereference of NULL pointer

Merge tag 'ata-5.17-rc1-part2' of git://git./linux/kernel/git/dlemoal/libata

Pull ATA fix from Damien Le Moal:
 "A single patch to fix a compilation error in the pata_octeon_cf driver
  (mips architecture), from me"

* tag 'ata-5.17-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata:
  ata: pata_octeon_cf: fix call to trace_ata_bmdma_stop()

Merge tag 'thermal-5.17-rc1-2' of git://git./linux/kernel/git/rafael/linux-pm

Pull more thermal control updates from Rafael Wysocki:
 "Add device IDs for Raptor Lake to the int340x thermal control driver
  (Srinivas Pandruvada)"

* tag 'thermal-5.17-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  thermal: int340x: Add Raptor Lake PCI device id
  thermal: int340x: Support Raptor Lake

Merge tag 'acpi-5.17-rc1-3' of git://git./linux/kernel/git/rafael/linux-pm

Pull extra ACPI updates from Rafael Wysocki:
 "These fix and clean up the ACPI CPPC driver on top of the recent
  changes in it merged previously and add some new device IDs to the
  ACPI DPTF driver.

  Specifics:

   - Fix a recently introduced endianness-related issue in the ACPI CPPC
     library and clean it up on top of that (Rafael Wysocki)

   - Add new device IDs for the Raptor Lake SoC to the ACPI DPTF driver
     (Srinivas Pandruvada)"

* tag 'acpi-5.17-rc1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  ACPI: DPTF: Support Raptor Lake
  ACPI: CPPC: Drop redundant local variable from cpc_read()
  ACPI: CPPC: Fix up I/O port access in cpc_read()

Merge tag 'devicetree-fixes-for-5.17-1' of git://git./linux/kernel/git/robh/linux

Pull devicetree fixes and cleanups from Rob Herring:

 - Fix a regression when probing a child device reusing the parent
   device's DT node pointer

 - Refactor of_parse_phandle*() variants to static inlines

 - Drop Enric Balletbo i Serra as a maintainer

 - Fix DT schemas with arrays incorrectly encoded as a matrix

 - Drop unneeded pinctrl properties from schemas

 - Add SPI peripheral schema to SPI based displays

 - Clean-up several schema examples

 - Clean-up trivial-devices.yaml comments

 - Add missing, in use vendor prefixes: Wingtech, Thundercomm, Huawei,
   F(x)tec, 8devices

* tag 'devicetree-fixes-for-5.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
  dt-bindings: google,cros-ec: drop Enric Balletbo i Serra from maintainers
  dt-bindings: display: bridge: drop Enric Balletbo i Serra from maintainers
  of: Check 'of_node_reused' flag on of_match_device()
  of: property: define of_property_read_u{8,16,32,64}_array() unconditionally
  of: base: make small of_parse_phandle() variants static inline
  dt-bindings: mfd: cirrus,madera: Fix 'interrupts' in example
  dt-bindings: Fix array schemas encoded as matrices
  dt-bindings: Drop unnecessary pinctrl properties
  dt-bindings: rtc: st,stm32-rtc: Make each example a separate entry
  dt-bindings: mmc: arm,pl18x: Make each example a separate entry
  dt-bindings: display: Add SPI peripheral schema to SPI based displays
  scripts/dtc: dtx_diff: remove broken example from help text
  dt-bindings: trivial-devices: fix double spaces in comments
  dt-bindings: trivial-devices: fix swapped comments
  dt-bindings: vendor-prefixes: add Wingtech
  dt-bindings: vendor-prefixes: add Thundercomm
  dt-bindings: vendor-prefixes: add Huawei
  dt-bindings: vendor-prefixes: add F(x)tec
  dt-bindings: vendor-prefixes: add 8devices
  dt-bindings: power: reset: gpio-restart: Correct default priority

Merge tag 'for-linus' of git://git./virt/kvm/kvm

Pull more kvm updates from Paolo Bonzini:
 "Generic:

   - selftest compilation fix for non-x86

   - KVM: avoid warning on s390 in mark_page_dirty

 x86:

   - fix page write-protection bug and improve comments

   - use binary search to lookup the PMU event filter, add test

   - enable_pmu module parameter support for Intel CPUs

   - switch blocked_vcpu_on_cpu_lock to raw spinlock

   - cleanups of blocked vCPU logic

   - partially allow KVM_SET_CPUID{,2} after KVM_RUN (5.16 regression)

   - various small fixes"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (46 commits)
  docs: kvm: fix WARNINGs from api.rst
  selftests: kvm/x86: Fix the warning in lib/x86_64/processor.c
  selftests: kvm/x86: Fix the warning in pmu_event_filter_test.c
  kvm: selftests: Do not indent with spaces
  kvm: selftests: sync uapi/linux/kvm.h with Linux header
  selftests: kvm: add amx_test to .gitignore
  KVM: SVM: Nullify vcpu_(un)blocking() hooks if AVIC is disabled
  KVM: SVM: Move svm_hardware_setup() and its helpers below svm_x86_ops
  KVM: SVM: Drop AVIC's intermediate avic_set_running() helper
  KVM: VMX: Don't do full kick when handling posted interrupt wakeup
  KVM: VMX: Fold fallback path into triggering posted IRQ helper
  KVM: VMX: Pass desired vector instead of bool for triggering posted IRQ
  KVM: VMX: Don't do full kick when triggering posted interrupt "fails"
  KVM: SVM: Skip AVIC and IRTE updates when loading blocking vCPU
  KVM: SVM: Use kvm_vcpu_is_blocking() in AVIC load to handle preemption
  KVM: SVM: Remove unnecessary APICv/AVIC update in vCPU unblocking path
  KVM: SVM: Don't bother checking for "running" AVIC when kicking for IPIs
  KVM: SVM: Signal AVIC doorbell iff vCPU is in guest mode
  KVM: x86: Remove defunct pre_block/post_block kvm_x86_ops hooks
  KVM: x86: Unexport LAPIC's switch_to_{hv,sw}_timer() helpers
  ...

Merge tag 'for-5.17/parisc-2' of git://git./linux/kernel/git/deller/parisc-linux

Pull more parisc architecture updates from Helge Deller:
 "Fixes and enhancements:

   - a memory leak fix in an error path in pdc_stable (Miaoqian Lin)

   - two compiler warning fixes in the TOC code

   - added autodetection for currently used console type (serial or
     graphics) which inserts console=<type> if it's missing"

* tag 'for-5.17/parisc-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
  parisc: pdc_stable: Fix memory leak in pdcs_register_pathentries
  parisc: Fix missing prototype for 'toc_intr' warning in toc.c
  parisc: Autodetect default output device and set console= kernel parameter
  parisc: Use safer strscpy() in setup_cmdline()
  parisc: Add visible flag to toc_stack variable

Merge tag 'riscv-for-linus-5.17-mw1' of git://git./linux/kernel/git/riscv/linux

Pull more RISC-V updates from Palmer Dabbelt:

 - Support for sv48 paging

 - Hart ID mappings are now sparse, which enables more CPUs to come up
   on systems with sparse hart IDs

 - A handful of cleanups and fixes

* tag 'riscv-for-linus-5.17-mw1' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux: (27 commits)
  RISC-V: nommu_virt: Drop unused SLAB_MERGE_DEFAULT
  RISC-V: Remove redundant err variable
  riscv: dts: sifive unmatched: Add gpio poweroff
  riscv: canaan: remove useless select of non-existing config SYSCON
  RISC-V: Do not use cpumask data structure for hartid bitmap
  RISC-V: Move spinwait booting method to its own config
  RISC-V: Move the entire hart selection via lottery to SMP
  RISC-V: Use __cpu_up_stack/task_pointer only for spinwait method
  RISC-V: Do not print the SBI version during HSM extension boot print
  RISC-V: Avoid using per cpu array for ordered booting
  riscv: default to CONFIG_RISCV_SBI_V01=n
  riscv: fix boolconv.cocci warnings
  riscv: Explicit comment about user virtual address space size
  riscv: Use pgtable_l4_enabled to output mmu_type in cpuinfo
  riscv: Implement sv48 support
  asm-generic: Prepare for riscv use of pud_alloc_one and pud_free
  riscv: Allow to dynamically define VA_BITS
  riscv: Introduce functions to switch pt_ops
  riscv: Split early kasan mapping to prepare sv48 introduction
  riscv: Move KASAN mapping next to the kernel mapping
  ...

Merge tag 'arm64-fixes' of git://git./linux/kernel/git/arm64/linux

Pull arm64 fixes/cleanups from Catalin Marinas:
 "Some fixes that turned up during the merge window:

   - Add brackets to the io_stop_wc macro

   - Avoid -Warray-bounds warning with the LSE atomics inline asm

   - Apply __ro_after_init to memory_limit"

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  arm64: mm: apply __ro_after_init to memory_limit
  arm64: atomics: lse: Dereference matching size
  asm-generic: Add missing brackets for io_stop_wc macro

Merge tag 'docs-5.17-2' of git://git.lwn.net/linux

Pull documentation fixes from Jonathan Corbet:
 "Three small documentation fixes"

* tag 'docs-5.17-2' of git://git.lwn.net/linux:
  Documentation: fix firewire.rst ABI file path error
  docs: ftrace: fix ambiguous sentence
  docs: staging/tee.rst: fix two typos found while reading

mm: hide the FRONTSWAP Kconfig symbol

Select FRONTSWAP from ZSWAP instead of prompting for it.

Link: https://lkml.kernel.org/r/20211224062246.1258487-14-hch@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Juergen Gross <jgross@suse.com>
Cc: Dan Streetman <ddstreet@ieee.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: Konrad Rzeszutek Wilk <Konrad.wilk@oracle.com>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Seth Jennings <sjenning@redhat.com>
Cc: Vitaly Wool <vitaly.wool@konsulko.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

frontswap: remove support for multiple ops

There is only a single instance of frontswap ops in the kernel, so
simplify the frontswap code by removing support for multiple operations.

Link: https://lkml.kernel.org/r/20211224062246.1258487-13-hch@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Juergen Gross <jgross@suse.com>
Cc: Dan Streetman <ddstreet@ieee.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: Konrad Rzeszutek Wilk <Konrad.wilk@oracle.com>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Seth Jennings <sjenning@redhat.com>
Cc: Vitaly Wool <vitaly.wool@konsulko.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm: mark swap_lock and swap_active_head static

swap_lock and swap_active_head are only used in swapfile.c, so mark them
static.

Link: https://lkml.kernel.org/r/20211224062246.1258487-12-hch@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Juergen Gross <jgross@suse.com>
Cc: Dan Streetman <ddstreet@ieee.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: Konrad Rzeszutek Wilk <Konrad.wilk@oracle.com>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Seth Jennings <sjenning@redhat.com>
Cc: Vitaly Wool <vitaly.wool@konsulko.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

frontswap: simplify frontswap_register_ops

Given that frontswap_register_ops must be called from built-in code,
there is no need to handle the case of swapfiles coming online before or
during it, so delete the code that deals with that case.

Link: https://lkml.kernel.org/r/20211224062246.1258487-11-hch@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Juergen Gross <jgross@suse.com>
Cc: Dan Streetman <ddstreet@ieee.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: Konrad Rzeszutek Wilk <Konrad.wilk@oracle.com>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Seth Jennings <sjenning@redhat.com>
Cc: Vitaly Wool <vitaly.wool@konsulko.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

frontswap: remove frontswap_test

frontswap_test is unused now, remove it.

Link: https://lkml.kernel.org/r/20211224062246.1258487-10-hch@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Juergen Gross <jgross@suse.com>
Cc: Dan Streetman <ddstreet@ieee.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: Konrad Rzeszutek Wilk <Konrad.wilk@oracle.com>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Seth Jennings <sjenning@redhat.com>
Cc: Vitaly Wool <vitaly.wool@konsulko.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm: simplify try_to_unuse

Remove the unused frontswap and pages_to_unuse arguments, and mark the
function static now that the caller in frontswap is gone.

[akpm@linux-foundation.org: fix shmem_unuse() stub, per Matthew]

Link: https://lkml.kernel.org/r/20211224062246.1258487-9-hch@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Juergen Gross <jgross@suse.com>
Cc: Dan Streetman <ddstreet@ieee.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: Konrad Rzeszutek Wilk <Konrad.wilk@oracle.com>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Seth Jennings <sjenning@redhat.com>
Cc: Vitaly Wool <vitaly.wool@konsulko.com>
Cc: Naresh Kamboju <naresh.kamboju@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

frontswap: remove the frontswap exports

None of the frontswap API is called from modular code.

Link: https://lkml.kernel.org/r/20211224062246.1258487-8-hch@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Juergen Gross <jgross@suse.com>
Cc: Dan Streetman <ddstreet@ieee.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: Konrad Rzeszutek Wilk <Konrad.wilk@oracle.com>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Seth Jennings <sjenning@redhat.com>
Cc: Vitaly Wool <vitaly.wool@konsulko.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

frontswap: simplify frontswap_init

Just use IS_ENABLED() and remove the __frontswap_init indirection.

Also remove the unused export.

Link: https://lkml.kernel.org/r/20211224062246.1258487-7-hch@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Juergen Gross <jgross@suse.com>
Cc: Dan Streetman <ddstreet@ieee.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: Konrad Rzeszutek Wilk <Konrad.wilk@oracle.com>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Seth Jennings <sjenning@redhat.com>
Cc: Vitaly Wool <vitaly.wool@konsulko.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

frontswap: remove frontswap_curr_pages

frontswap_curr_pages is never called, so remove it.

Link: https://lkml.kernel.org/r/20211224062246.1258487-6-hch@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Juergen Gross <jgross@suse.com>
Cc: Dan Streetman <ddstreet@ieee.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: Konrad Rzeszutek Wilk <Konrad.wilk@oracle.com>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Seth Jennings <sjenning@redhat.com>
Cc: Vitaly Wool <vitaly.wool@konsulko.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

frontswap: remove frontswap_shrink

frontswap_shrink is never called, so remove it.

Link: https://lkml.kernel.org/r/20211224062246.1258487-5-hch@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Juergen Gross <jgross@suse.com>
Cc: Dan Streetman <ddstreet@ieee.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: Konrad Rzeszutek Wilk <Konrad.wilk@oracle.com>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Seth Jennings <sjenning@redhat.com>
Cc: Vitaly Wool <vitaly.wool@konsulko.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

frontswap: remove frontswap_tmem_exclusive_gets

frontswap_tmem_exclusive_gets is never called, so remove it.

Link: https://lkml.kernel.org/r/20211224062246.1258487-4-hch@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Juergen Gross <jgross@suse.com>
Cc: Dan Streetman <ddstreet@ieee.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: Konrad Rzeszutek Wilk <Konrad.wilk@oracle.com>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Seth Jennings <sjenning@redhat.com>
Cc: Vitaly Wool <vitaly.wool@konsulko.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

frontswap: remove frontswap_writethrough

frontswap_writethrough is never called, so remove it.

Link: https://lkml.kernel.org/r/20211224062246.1258487-3-hch@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Juergen Gross <jgross@suse.com>
Cc: Dan Streetman <ddstreet@ieee.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: Konrad Rzeszutek Wilk <Konrad.wilk@oracle.com>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Seth Jennings <sjenning@redhat.com>
Cc: Vitaly Wool <vitaly.wool@konsulko.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm: remove cleancache

Patch series "remove Xen tmem leftovers".

Since the removal of the Xen tmem driver in 2019, the cleancache hooks
are entirely unused, as are large parts of frontswap.  This series
against linux-next (with the folio changes included) removes
cleancaches, and cuts down frontswap to the bits actually used by zswap.

This patch (of 13):

The cleancache subsystem is unused since the removal of Xen tmem driver
in commit 814bbf49dcd0 ("xen: remove tmem driver").

[akpm@linux-foundation.org: remove now-unreachable code]

Link: https://lkml.kernel.org/r/20211224062246.1258487-1-hch@lst.de
Link: https://lkml.kernel.org/r/20211224062246.1258487-2-hch@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Juergen Gross <jgross@suse.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Konrad Rzeszutek Wilk <Konrad.wilk@oracle.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Seth Jennings <sjenning@redhat.com>
Cc: Dan Streetman <ddstreet@ieee.org>
Cc: Vitaly Wool <vitaly.wool@konsulko.com>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

lib/stackdepot: always do filter_irq_stacks() in stack_depot_save()

The non-interrupt portion of interrupt stack traces before interrupt
entry is usually arbitrary.  Therefore, saving stack traces of
interrupts (that include entries before interrupt entry) to stack depot
leads to unbounded stackdepot growth.

As such, use of filter_irq_stacks() is a requirement to ensure
stackdepot can efficiently deduplicate interrupt stacks.

Looking through all current users of stack_depot_save(), none (except
KASAN) pass the stack trace through filter_irq_stacks() before passing
it on to stack_depot_save().

Rather than adding filter_irq_stacks() to all current users of
stack_depot_save(), it became clear that stack_depot_save() should
simply do filter_irq_stacks().

Link: https://lkml.kernel.org/r/20211130095727.2378739-1-elver@google.com
Signed-off-by: Marco Elver <elver@google.com>
Reviewed-by: Alexander Potapenko <glider@google.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Reviewed-by: Andrey Konovalov <andreyknvl@gmail.com>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Vijayanand Jitta <vjitta@codeaurora.org>
Cc: "Gustavo A. R. Silva" <gustavoars@kernel.org>
Cc: Imran Khan <imran.f.khan@oracle.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

lib/stackdepot: allow optional init and stack_table allocation by kvmalloc()

Currently, enabling CONFIG_STACKDEPOT means its stack_table will be
allocated from memblock, even if stack depot ends up not actually used.
The default size of stack_table is 4MB on 32-bit, 8MB on 64-bit.

This is fine for use-cases such as KASAN which is also a config option
and has overhead on its own.  But it's an issue for functionality that
has to be actually enabled on boot (page_owner) or depends on hardware
(GPU drivers) and thus the memory might be wasted.  This was raised as
an issue [1] when attempting to add stackdepot support for SLUB's debug
object tracking functionality.  It's common to build kernels with
CONFIG_SLUB_DEBUG and enable slub_debug on boot only when needed, or
create only specific kmem caches with debugging for testing purposes.

It would thus be more efficient if stackdepot's table was allocated only
when actually going to be used.  This patch thus makes the allocation
(and whole stack_depot_init() call) optional:

 - Add a CONFIG_STACKDEPOT_ALWAYS_INIT flag to keep using the current
   well-defined point of allocation as part of mem_init(). Make
   CONFIG_KASAN select this flag.

 - Other users have to call stack_depot_init() as part of their own init
   when it's determined that stack depot will actually be used. This may
   depend on both config and runtime conditions. Convert current users
   which are page_owner and several in the DRM subsystem. Same will be
   done for SLUB later.

 - Because the init might now be called after the boot-time memblock
   allocation has given all memory to the buddy allocator, change
   stack_depot_init() to allocate stack_table with kvmalloc() when
   memblock is no longer available. Also handle allocation failure by
   disabling stackdepot (could have theoretically happened even with
   memblock allocation previously), and don't unnecessarily align the
   memblock allocation to its own size anymore.

[1] https://lore.kernel.org/all/CAMuHMdW=eoVzM1Re5FVoEN87nKfiLmM2+Ah7eNu2KXEhCvbZyA@mail.gmail.com/

Link: https://lkml.kernel.org/r/20211013073005.11351-1-vbabka@suse.cz
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Dmitry Vyukov <dvyukov@google.com>
Reviewed-by: Marco Elver <elver@google.com> # stackdepot
Cc: Marco Elver <elver@google.com>
Cc: Vijayanand Jitta <vjitta@codeaurora.org>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Andrey Konovalov <andreyknvl@gmail.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Oliver Glitta <glittao@gmail.com>
Cc: Imran Khan <imran.f.khan@oracle.com>
From: Colin Ian King <colin.king@canonical.com>
Subject: lib/stackdepot: fix spelling mistake and grammar in pr_err message

There is a spelling mistake of the work allocation so fix this and
re-phrase the message to make it easier to read.

Link: https://lkml.kernel.org/r/20211015104159.11282-1-colin.king@canonical.com
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
From: Vlastimil Babka <vbabka@suse.cz>
Subject: lib/stackdepot: allow optional init and stack_table allocation by kvmalloc() - fixup

On FLATMEM, we call page_ext_init_flatmem_late() just before
kmem_cache_init() which means stack_depot_init() (called by page owner
init) will not recognize properly it should use kvmalloc() and not
memblock_alloc().  memblock_alloc() will also not issue a warning and
return a block memory that can be invalid and cause kernel page fault when
saving stacks, as reported by the kernel test robot [1].

Fix this by moving page_ext_init_flatmem_late() below kmem_cache_init() so
that slab_is_available() is true during stack_depot_init().  SPARSEMEM
doesn't have this issue, as it doesn't do page_ext_init_flatmem_late(),
but a different page_ext_init() even later in the boot process.

Thanks to Mike Rapoport for pointing out the FLATMEM init ordering issue.

While at it, also actually resolve a checkpatch warning in stack_depot_init()
from DRM CI, which was supposed to be in the original patch already.

[1] https://lore.kernel.org/all/20211014085450.GC18719@xsang-OptiPlex-9020/

Link: https://lkml.kernel.org/r/6abd9213-19a9-6d58-cedc-2414386d2d81@suse.cz
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Reported-by: kernel test robot <oliver.sang@intel.com>
Cc: Mike Rapoport <rppt@kernel.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
From: Vlastimil Babka <vbabka@suse.cz>
Subject: lib/stackdepot: allow optional init and stack_table allocation by kvmalloc() - fixup3

Due to cd06ab2fd48f ("drm/locking: add backtrace for locking contended
locks without backoff") landing recently to -next adding a new stack depot
user in drivers/gpu/drm/drm_modeset_lock.c we need to add an appropriate
call to stack_depot_init() there as well.

Link: https://lkml.kernel.org/r/2a692365-cfa1-64f2-34e0-8aa5674dce5e@suse.cz
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Naresh Kamboju <naresh.kamboju@linaro.org>
Cc: Marco Elver <elver@google.com>
Cc: Vijayanand Jitta <vjitta@codeaurora.org>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Andrey Konovalov <andreyknvl@gmail.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Oliver Glitta <glittao@gmail.com>
Cc: Imran Khan <imran.f.khan@oracle.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
From: Vlastimil Babka <vbabka@suse.cz>
Subject: lib/stackdepot: allow optional init and stack_table allocation by kvmalloc() - fixup4

Due to 4e66934eaadc ("lib: add reference counting tracking
infrastructure") landing recently to net-next adding a new stack depot
user in lib/ref_tracker.c we need to add an appropriate call to
stack_depot_init() there as well.

Link: https://lkml.kernel.org/r/45c1b738-1a2f-5b5f-2f6d-86fab206d01c@suse.cz
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Cc: Jiri Slab <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

proc: remove PDE_DATA() completely

Remove PDE_DATA() completely and replace it with pde_data().

[akpm@linux-foundation.org: fix naming clash in drivers/nubus/proc.c]
[akpm@linux-foundation.org: now fix it properly]

Link: https://lkml.kernel.org/r/20211124081956.87711-2-songmuchun@bytedance.com
Signed-off-by: Muchun Song <songmuchun@bytedance.com>
Acked-by: Christian Brauner <christian.brauner@ubuntu.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Alexey Gladkov <gladkov.alexey@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fs: proc: store PDE()->data into inode->i_private

PDE_DATA(inode) is introduced to get user private data and hide the
layout of struct proc_dir_entry.  The inode->i_private is used to do the
same thing as well.  Save a copy of user private data to inode->
i_private when proc inode is allocated.  This means the user also can
get their private data by inode->i_private.

Introduce pde_data() to wrap inode->i_private so that we can remove
PDE_DATA() from fs/proc/generic.c and make PTE_DATE() as a wrapper of
pde_data().  It will be easier if we decide to remove PDE_DATE() in the
future.

Link: https://lkml.kernel.org/r/20211124081956.87711-1-songmuchun@bytedance.com
Signed-off-by: Muchun Song <songmuchun@bytedance.com>
Acked-by: Christian Brauner <christian.brauner@ubuntu.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Alexey Gladkov <gladkov.alexey@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

zsmalloc: replace get_cpu_var with local_lock

The usage of get_cpu_var() in zs_map_object() is problematic because it
disables preemption and makes it impossible to acquire any sleeping lock
on PREEMPT_RT such as a spinlock_t.

Replace the get_cpu_var() usage with a local_lock_t which is embedded
struct mapping_area.  It ensures that the access the struct is
synchronized against all users on the same CPU.

[minchan: remove the bit_spin_lock part and change the title]

Link: https://lkml.kernel.org/r/20211115185909.3949505-10-minchan@kernel.org
Signed-off-by: Mike Galbraith <umgwanakikbuti@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Minchan Kim <minchan@kernel.org>
Tested-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Sergey Senozhatsky <senozhatsky@chromium.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

zsmalloc: replace per zpage lock with pool->migrate_lock

The zsmalloc has used a bit for spin_lock in zpage handle to keep zpage
object alive during several operations.  However, it causes the problem
for PREEMPT_RT as well as introducing too complicated.

This patch replaces the bit spin_lock with pool->migrate_lock rwlock.
It could make the code simple as well as zsmalloc work under PREEMPT_RT.

The drawback is the pool->migrate_lock is bigger granuarity than per
zpage lock so the contention would be higher than old when both
IO-related operations(i.e., zsmalloc, zsfree, zs_[map|unmap]) and
compaction(page/zpage migration) are going in parallel(*, the
migrate_lock is rwlock and IO related functions are all read side lock
so there is no contention).  However, the write-side is fast
enough(dominant overhead is just page copy) so it wouldn't affect much.
If the lock granurity becomes more problem later, we could introduce
table locks based on handle as a hash value.

Link: https://lkml.kernel.org/r/20211115185909.3949505-9-minchan@kernel.org
Signed-off-by: Minchan Kim <minchan@kernel.org>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Mike Galbraith <umgwanakikbuti@gmail.com>
Cc: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Sergey Senozhatsky <senozhatsky@chromium.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

locking/rwlocks: introduce write_lock_nested

In preparation for converting bit_spin_lock to rwlock in zsmalloc so
that multiple writers of zspages can run at the same time but those
zspages are supposed to be different zspage instance.  Thus, it's not
deadlock.  This patch adds write_lock_nested to support the case for
LOCKDEP.

[minchan@kernel.org: fix write_lock_nested for RT]
Link: https://lkml.kernel.org/r/YZfrMTAXV56HFWJY@google.com
[bigeasy@linutronix.de: fixup write_lock_nested() implementation]
Link: https://lkml.kernel.org/r/20211123170134.y6xb7pmpgdn4m3bn@linutronix.de
Link: https://lkml.kernel.org/r/20211115185909.3949505-8-minchan@kernel.org
Signed-off-by: Minchan Kim <minchan@kernel.org>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Mike Galbraith <umgwanakikbuti@gmail.com>
Cc: Sergey Senozhatsky <senozhatsky@chromium.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Naresh Kamboju <naresh.kamboju@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

zsmalloc: remove zspage isolation for migration

zspage isolation for migration introduced additional exceptions to be
dealt with since the zspage was isolated from class list.  The reason
why I isolated zspage from class list was to prevent race between
obj_malloc and page migration via allocating zpage from the zspage
further.  However, it couldn't prevent object freeing from zspage so it
needed corner case handling.

This patch removes the whole mess.  Now, we are fine since class->lock
and zspage->lock can prevent the race.

Link: https://lkml.kernel.org/r/20211115185909.3949505-7-minchan@kernel.org
Signed-off-by: Minchan Kim <minchan@kernel.org>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Mike Galbraith <umgwanakikbuti@gmail.com>
Cc: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Sergey Senozhatsky <senozhatsky@chromium.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>