stm32f4: fix gpio description in comment

On STM32F429 gpio PC6/PC7 can be allocated for USART6, as
reported in the comment.
But current code in
drivers/serial/serial_stm32.c
uses a different gpio mapping (PG14/PG9) for USART6.

Fix the comment to match current code in the driver.

Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
To: u-boot@lists.denx.de
To: Kamil Lulko <rev13@wp.pl>
Cc: Tom Rini <trini@konsulko.com>

stm32f4: fix minor typo in comment

Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
To: u-boot@lists.denx.de
To: Kamil Lulko <rev13@wp.pl>
Cc: Tom Rini <trini@konsulko.com>

stm32f4: fix MAINTAINERS file

When "scripts/get_maintainer.pl" parses "board/.../MAINTAINERS",
it uses the line containing board name as delimiter.
Without this line, the script happily mixes the lines from current
board MAINTAINERS file with lines from another file.

Fix it by adding a reasonable board name.

Tested by comparing output of:
cat board/st/stm32f429-discovery/MAINTAINERS
./scripts/get_maintainer.pl -f board/st/stm32f429-discovery

Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
To: u-boot@lists.denx.de
To: Kamil Lulko <rev13@wp.pl>
Cc: Tom Rini <trini@konsulko.com>

siemens,am33x: adjust mtd partition

Use one mtd partition for rootfs and configuration by
means of ubi volumes and get rid of configuration partition.
We can use partition layout for both 256MB and 512MB flash.

Signed-off-by: Samuel Egli <samuel.egli@siemens.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Roger Meier <r.meier@siemens.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Heiko Schocher <hs@denx.de>

arm: baltos: fix NAND boot

Specify proper U-Boot offset, enable prefetch mode,
increase bootm size and add FIT fallback, if board_name
is not present in kernel-fit.itb image.

Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>

arm: baltos: drop I2C speed to 1000 Hz

This action is need to make I2C communication with PMIC
stable for low temperature. Print current I2C speed in
SPL for visual control.

Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>

arm: baltos: enable CMD_NET and FIT support in defconfig

Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

arm: convert am3517_crane and am3517_evm to generic boards

Add CONFIG_SYS_GENERIC_BOARD to board's config header.

Boot-tested on am3517_evm board.

Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>

ARM: beagle_x15: prevent DCAN1 _wait_target_disable failure in kernel

If board is booted with transitions happening on DCAN1 pins then
the following warning is seen in the kernel at boot when the
hwmod layer initializes.

"omap_hwmod: dcan1: _wait_target_disable failed"

This is because DCAN1 module's SWAKEUP mechanism is broken
and it fails to correctly turn OFF if it sees a transition on the
DCAN1 pins. Suggested workaround is to keep DCAN1 pins in safe mode
while enabling/disabling DCAN1 module.

The hwmod layer enables and disables all modules at boot
and we have no opportunity to put the DCAN1 pins in safe mode
at that point.

DCAN1 is not used by u-boot so it doesn't matter to it if these
pins are in safe mode. The kernel driver correctly configures
the right mode when DCAN1 is active.

Signed-off-by: Roger Quadros <rogerq@ti.com>
[trini: s/PULLUP/PULL_UP/ based on DRA7xx EVM version of this patch]
Signed-off-by: Tom Rini <trini@konsulko.com>

ARM: DRA7-evm: prevent DCAN1 _wait_target_disable failure in kernel

If board is booted with transitions happening on DCAN1 pins then
the following warning is seen in the kernel at boot when the
hwmod layer initializes.

"omap_hwmod: dcan1: _wait_target_disable failed"

This is because DCAN1 module's SWAKEUP mechanism is broken
and it fails to correctly turn OFF if it sees a transition on the
DCAN1 pins. Suggested workaround is to keep DCAN1 pins in safe mode
while enabling/disabling DCAN1 module.

The hwmod layer enables and disables all modules at boot
and we have no opportunity to put the DCAN1 pins in safe mode
at that point.

DCAN1 is not used by u-boot so it doesn't matter to it if these
pins are in safe mode. The kernel driver correctly configures
the right mode when DCAN1 is active.

Signed-off-by: Roger Quadros <rogerq@ti.com>

Makefile:Add GCC flag -fno-delete-null-pointer-checks

-fdelete-null-pointer-checks flag controls global dataflow analyses and
eliminate useless checks for null pointers; It assume that if a pointer is
checked after it has already been dereferenced, it cannot be null.
This flag is enabled by default.

gcc v4.9 has more optimizations added to this option. Hence it is very
aggressive with GCC v4.9 series. Add -fno-delete-null-pointer-checks to
disable the optimization

Signed-off-by: Rohit Dharmakan <rohitarulraj@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>

ti: Add SPDX license identifier to omap.h

This also came from Linux - according to this thread it has a GPL v2
license like arch/arm/mach-omap2/mux.h:

http://lists.denx.de/pipermail/u-boot/2015-June/217827.html

Signed-off-by: Simon Glass <sjg@chromium.org>
Reported-by: Ingrid Viitanen <ingrid.viitanen@nokia.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

README.distro: fix typos

The word "partition" is doubled.  Keep decent forms for the
following lines.

Also, fix some other typos while we are here.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Stephen Warren <swarren@nvidia.com>

blackfin: Fix build regression due to image size

bf533-stamp, bf538f-ezkit, and cm-bf548 are very space limited.

This was introduced by:
6e0d26c0502e (net: Handle ethaddr changes as an env callback)
by enabling CONFIG_REGEX, which is too big for these boards.

This patch disables CONFIG_REGEX at the expense of working with more
than the first ethaddr.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>

Allow CONFIG_REGEX to be disabled when CONFIG_NET

Instead of selecting REGEX when NET is enabled, make it the default, but
allow boards that are tiny to disable it and lose functionality on all
but the first Ethernet adapter.

cm-bf548, bf538f-ezkit, and bf533-stamp need this. None appear to have
more than one Ethernet interface.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>

Merge branch 'master' of git://git.denx.de/u-boot-mips

net: designware: Program MAC address to hardware after soft reset

commit f566c99 "net: Update hardware MAC address if it changes in env"
removes writing MAC address to designware controller after soft reset.
This makes designware ethernet port fail to work. Actually the MAC
address should always be programmed after soft reset.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

sunxi: Adjust Ippo_q8h_v1_2_a33_1024x600 dts filename to match the upstream kernel

sun8i-a33-ippo-q8h-v1.2-lcd1024x600.dts has been merged into the upstream
Linux kernel as sun8i-a33-ippo-q8h-v1.2.dts, adjust u-boot to follow.

Note we've never shipped a final u-boot version with the old name, so this
is safe todo.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>

ARM: DRA72x: fix io delay calibration for ethernet

we currently use in-development IODelay values for DRA72x which are
proposed in the data sheet, however, DRA72x EVM uses DP83865 ethernet
Phy over RGMII. The PHY characteristics and routing choices made on
the EVM, make the current iodelay values fail ethernet communication.

Instead, we need to choose custom values for DRA72x-evm specifically
designed for the PHY and routing on the platform for ethernet to
function.

Cc: Nishanth Menon <nm@ti.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>

Merge branch 'master' of git://git.denx.de/u-boot-arm

board: baltos - add maintainer information

Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>

ARM: disable HAVE_PRIVATE_LIBGCC for ARM64

We have not supported the private library for ARM 64bit.
Prohibit ARM64 boards from enabling it until we make things ready.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

board: am43xx: Add maintainer information

am43xx_evm_ethboot/usbhost_boot_defconfig entries are
missing in MAINTAINER file. Adding entries for them.

Reported-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>

cairo: add missing MAINTAINERS file

This removes the following two warnings from buildman:

WARNING: no status info for 'cairo'
WARNING: no maintainers for 'cairo'

Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>

arm: dcc: Add uart dcc support for armv8

Added UART DCC support for armv8

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

Revert "break build if it would produce broken binary"

The root cause of this problem should now be fixed.

This reverts commit a6a4c542d316b3401f0840ac5378743191bca851.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Pavel Machek <pavel@denx.de>
Tested-by: Pavel Machek <pavel@denx.de>

arm: Add ENTRY/ENDPROC to private libgcc functions

When CONFIG_SYS_THUMB_BUILD is defined these functions may be called from
Thumb code. Add the required ENTRY and ENDPROC bracketing so that BLX is
used to call these ARM functions, instead of plain BL, which will fail.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reported-by: Pavel Machek <pavel@denx.de>

Merge branch 'u-boot/master' into 'u-boot-arm/master'

armv7: better comment in start.S

Fix big/small letters in comment.

Signed-off-by: Pavel Machek <pavel@denx.de>
Tested-by: Marek Vasut <marex@denx.de>

gpio: lpc32xx: Use priv_data instead of platdata

The LPC32XX GPIO driver platdata currently contains GPIO state information,
which should go into priv_data. Thus rename lpc32xx_gpio_platdata to
lpc32xx_gpio_priv and convert to use dev_get_priv() instead.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Albert ARIBAUD <albert.aribaud@3adev.fr>

Merge branch 'master' of git.denx.de/u-boot-sunxi

sunxi: Add Sinlinx SinA33 defconfig

Sinlinx SinA33 is a core/daughter board SDK kit from Sinlinx. It has
the A33 SoC, USB host, USB OTG, audio input/output, LCD, camera, SDIO
and GPIO headers.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

sunxi: Sync sun8i dts files with the linux kernel

Copy over all the latest dts changes from mripard/sunxi/dt-for-4.2.
This adds a dts file for Sinlinx SinA33 dev board, and the required
changes in the .dtsi files.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

sunxi: Add support for UART0 in PB pin group on A33

The A33 adds a pinmux function for UART0 in the PB pin group.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

sunxi: rsb: Enable R_PIO clock before configuring external pins

The original code was configuring the external pins after enabling
the R_PIO clock, which meant the configuration never made it to
the pin controller the first time in SPL.

Why this was working before is uncertain. Maybe the state was left
from a previous boot sequence, or RSB just happened to be the default
configuration. However with some A33 chips, SPL failed to configure
the PMIC. This was seen by me and Maxime on the Sinlinx SinA33 dev
board.

Reordering the calls fixed this.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

sunxi: hardware-feature-specific function index defines for PORT F UART0

Commit 487b327 ("sunxi: GPIO pin mux hardware-feature-specific function
index defines") renamed all GPIO index defines, but missed the PORT F
UART0 setup functions.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

Merge branch 'master' of git://denx.de/git/u-boot-imx

Conflicts:
configs/tbs2910_defconfig
configs/tqma6q_mba6_mmc_defconfig
configs/tqma6q_mba6_spi_defconfig
configs/tqma6s_mba6_mmc_defconfig
configs/tqma6s_mba6_spi_defconfig
include/configs/mx6_common.h

Signed-off-by: Tom Rini <trini@konsulko.com>

colibri_vf: Increase console IO buffer size to 1024

Increase console IO buffer size to 1024 from the previous value of 256.
The previous value was too short for editing environment variables like
ubiboot from the console.

Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>

MIPS: change 'extern inline' to 'static inline'

The kernel changed it a long time ago. Also this is now broken
on gcc-5.x.

Reported-by: Andy Kennedy <andy.kennedy@adtran.com>
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>

MIPS: fix missing semicolon in cacheops.h

Fix missing semicolon in cacheops.h introduced in commit
2b8bcc5a2 (MIPS: avoid .set ISA for cache operations)

Signed-off-by: Tony Wu <tung7970@gmail.com>
Cc: Paul Burton <paul.burton@imgtec.com>

Merge branch 'master' of git://git.denx.de/u-boot-spi

Merge branch 'master' of git://git.denx.de/u-boot-uniphier

spi: cf_qspi: fix clamp macro type check compilation warnings

Fix compilation warnings for redefined 'clamp' macro and non-uniform
clamp macro types.

Signed-off-by: Angelo Dureghello <angelo@sysam.it>
Reviewed-by: Jagannadh Teki <jteki@openedev.com>

README: Remove CONFIG_SPI_FLASH_DATAFLASH help text

Since the help text is added in drivers/mtd/spi/Kconfig

Signed-off-by: Jagan Teki <jteki@openedev.com>

README: Remove CONFIG_SPI_FLASH_BAR help text

Since the help text is added in drivers/mtd/spi/Kconfig

Signed-off-by: Jagan Teki <jteki@openedev.com>

sf: Kconfig: Add SPI_FLASH_BAR entry

Added SPI_FLASH_BAR entry on Kconfig with help description

Signed-off-by: Jagan Teki <jteki@openedev.com>

defconfig: Move CONFIG_SPI_FLASH_BAR from configs

This commit moves:
- CONFIG_SPI_FLASH_BAR

from include/configs/*.h into configs/*_defconfigs

Signed-off-by: Jagan Teki <jteki@openedev.com>

README: Remove CONFIG_SPI_FLASH_MTD help text

Since the help text is added in drivers/mtd/spi/Kconfig

Signed-off-by: Jagan Teki <jteki@openedev.com>

spi: Kconfig: Add TEGRA20_SLINK entry

Added TEGRA20_SLINK entry on Kconfig with help description.

Signed-off-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Stephen Warren <swarren@nvidia.com>

spi: Kconfig: Add TEGRA20_SFLASH entry

Added TEGRA20_SFLASH entry on Kconfig with help description.

Signed-off-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Stephen Warren <swarren@nvidia.com>

spi: Kconfig: Add TEGRA114_SPI entry

Added TEGRA114_SPI entry on Kconfig with help description.

Signed-off-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Stephen Warren <swarren@nvidia.com>

spi: Kconfig: Add ICH_SPI entry

Added ICH_SPI entry on Kconfig with help description.

Signed-off-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>

spi: Kconfig: Add EXYNOS_SPI entry

Added EXYNOS_SPI entry on Kconfig with help description.

Signed-off-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

spi: Kconfig: Add FSL_QSPI entry

Added FSL_QSPI entry on Kconfig with help description.

Signed-off-by: Jagan Teki <jteki@openedev.com>
Cc: Peng Fan <Peng.Fan@freescale.com>
Cc: Haikun Wang <haikun.wang@freescale.com>

spi: Kconfig: Add FSL_ESPI entry

Added FSL_ESPI entry on Kconfig with help description.

Signed-off-by: Jagan Teki <jteki@openedev.com>
Cc: Haikun Wang <haikun.wang@freescale.com>

spi: Kconfig: Add FSL_DSPI entry

Added FSL_DSPI entry on Kconfig with help description.

Signed-off-by: Jagan Teki <jteki@openedev.com>
Cc: Haikun Wang <haikun.wang@freescale.com>

spi: Kconfig: Show dm-spi drivers if DM_SPI set

DM supported spi drivers are enbled only when DM_SPI enabled,
so added DM_SPI if condition in Kconfig to show thoese only
when it enabled.

Also re-order the config items as incresing alphabetic order.

Signed-off-by: Jagan Teki <jteki@openedev.com>

spi: Makefile: Use object file alphabetic order

Use object files as incresing alphabetic order, so-that it's
easy for readability.

Signed-off-by: Jagan Teki <jteki@openedev.com>

spi: Kconfig: Add TI_QSPI entry

Added TI_QSPI entry on Kconfig with help description.

Signed-off-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

spi: Kconfig: Add XILINX_SPI entry

Added XILINX_SPI entry on Kconfig with help description.

Signed-off-by: Jagan Teki <jteki@openedev.com>
Cc: Michal Simek <michal.simek@xilinx.com>

spi: Add Kconfig menu entry

Added Kconfig menu ... endmenu enties for spi support.

Signed-off-by: Jagan Teki <jteki@openedev.com>

ARM: UniPhier: add IDs for PH1-Pro5, ProXstream2, PH1-LD6b

This prepares for new SoCs support.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

ARM: dts: UniPhier: re-license device tree files under GPLv2+/X11

The current GPL only licensing on the device trees makes it very
impractical for other software components licensed under another
license.

To make it easier to reuse them, the device trees for UniPhier
SoCs and boards have already been dual-licensed in Linux.

Follow this trend in U-boot too.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

ARM: dts: UniPhier: sync device trees with the Linux kernel

This makes code diff much easier.

Device trees describe hardware attributes, which are independent
of software architecture.  It generally makes sense to synchronize
them beyond software projects.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

ARM: UniPhier: drop special CONFIG_AUTOBOOT_ settings

There is no good reason to use a particular key to stop autobooting.
The default allows us to stop the autoboot with any key input.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

sf: Kconfig: Add SPI_FLASH_DATAFLASH entry

Added SPI_FLASH_DATAFLASH entry on Kconfig with help description.

data flash driver comes with good decription, hence moved the
same on to kconfig help decription.

Signed-off-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Haikun Wang <haikun.wang@freescale.com>

sf: Kconfig: Add SPI_FLASH_MTD entry

Added SPI_FLASH_MTD entry on Kconfig with help description.

Signed-off-by: Jagan Teki <jteki@openedev.com>
Acked-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Heiko Schocher <hs@denx.de>

sf: Kconfig: Update SPI_FLASH entry

Updated SPI_FLASH entry on Kconfig with depends on
and along with config help description.

Signed-off-by: Jagan Teki <jteki@openedev.com>

common: Add CMD_SF Kconfig entry

Added Kconfig entry for CMD_SF.

Signed-off-by: Jagan Teki <jteki@openedev.com>

sf: Add Kconfig menu entry

Added Kconfig menu ... endmenu enties for spi flash suppor

Signed-off-by: Jagan Teki <jteki@openedev.com>

README: Add CONFIG_SPI_FLASH_DATAFLASH description

This patch adds CONFIG_SPI_FLASH_DATAFLASH descrition on README
file for more readble for users.

Signed-off-by: Jagan Teki <jteki@openedev.com>

sf: dataflash: Rename to CONFIG_SPI_FLASH_DATAFLASH

Rename CONFIG_SF_DATAFLASH into CONFIG_SPI_FLASH_DATAFLASH
as it follows the naming convention same as remaining configs.

Signed-off-by: Jagan Teki <jteki@openedev.com>

zynq: defconfig: Move CONFIG_OF_* to Kconfig

This commit moves:
- CONFIG_OF_CONTROL
- SPL_DISABLE_OF_CONTROL

from zynq_*_defconfig files into arch/arm/Kconfig "config ARCH_ZYNQ"

Signed-off-by: Jagan Teki <jteki@openedev.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>

defconfig: Add CONFIG_OF_CONTROL in zynq_picozed

Enable FDT support for zynq_picozed board.

Signed-off-by: Jagan Teki <jteki@openedev.com>

spi: Kconfig: Add Zynq SPI controller entry

Add Zynq SPI controller Kconfig entry.

Signed-off-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Marek Vasut <marex@denx.de>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>

spi: xilinx_spi: Add asm/io.h include file

This patch includes asm/io.h for readl and writel calls.

build errors:
drivers/spi/xilinx_spi.c: In function 'xilinx_spi_probe':
drivers/spi/xilinx_spi.c:119:2: warning: implicit declaration of function 'writel' [-Wimplicit-function-declaration]
drivers/spi/xilinx_spi.c: In function 'xilinx_spi_xfer':
drivers/spi/xilinx_spi.c:193:2: warning: implicit declaration of function 'readl' [-Wimplicit-function-declaration]

Signed-off-by: Jagan Teki <jteki@openedev.com>
Cc: Michal Simek <michal.simek@xilinx.com>

dm: spi: xilinx_spi: Convert to driver model

This converts the xilinx spi driver to use the driver model.

Signed-off-by: Jagan Teki <jteki@openedev.com>
Acked-by: Simon Glass <sjg@chromium.org>
Cc: Michal Simek <michal.simek@xilinx.com>

dts: zynq: Enable spi1 for zc770_xm010 board

This patch enables spi1 for zynq zc770_xm010 board dts

Signed-off-by: Jagan Teki <jteki@openedev.com>
Tested-by: Jagan Teki <jteki@openedev.com>

spi: zynq_spi: Add fdt support in driver

Now zynq spi driver platform data is controlled by devicetree,
enable the status by saying "okay" on respective board dts to use
the devicetree generated platdata.

Ex:
&spi1 {
status = "okay";
};

Signed-off-by: Jagan Teki <jteki@openedev.com>
Acked-by: Simon Glass <sjg@chromium.org>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Tested-by: Jagan Teki <jteki@openedev.com>

dts: zynq: Add zynq spi controller nodes

This patch adds zynq spi controller nodes in zynq-7000.dtsi.

Signed-off-by: Jagan Teki <jteki@openedev.com>
Acked-by: Simon Glass <sjg@chromium.org>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Tested-by: Jagan Teki <jteki@openedev.com>

zynq: Kconfig: Enable dm spi and spi_flash

Enabled CONFIG_DM_SPI and CONFIG_DM_SPI_FLASH for zynq soc.

Signed-off-by: Jagan Teki <jteki@openedev.com>
Acked-by: Simon Glass <sjg@chromium.org>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Tested-by: Jagan Teki <jteki@openedev.com>

dm: spi: zynq_spi: Convert to driver model

This converts the zynq spi driver to use the driver model.

Minimal functional changes like using meaningful name on
structure members wrt mainlined dm spi drivers.
- input_hz -> frequency
- req_hz -> freq
- base -> regs

Signed-off-by: Jagan Teki <jteki@openedev.com>
Acked-by: Simon Glass <sjg@chromium.org>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Tested-by: Jagan Teki <jteki@openedev.com>

spi/sf: Minor cleanups

- Adjust tab spaces
- Add comments

Signed-off-by: Jagan Teki <jteki@openedev.com>

spi: davinci_spi: Driver cleanup

Arrange driver code in more readable format[1] for easy accessing
and readable.
[1] http://patchwork.ozlabs.org/patch/265683/

Signed-off-by: Jagan Teki <jteki@openedev.com>
Cc: Rex Chang <rchang@ti.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>

spi: davinci_spi: Move header code to driver

Move the header code into driver for more readable and
easy to access it.

Signed-off-by: Jagan Teki <jteki@openedev.com>
Cc: Rex Chang <rchang@ti.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>

spi: xilinx_spi: Driver clean-up

- Zap unneeded macros
- Re-arrange the code
- Removed __attribute__((weak))
- Replace __func__ macro with func names to save macro transition.
- Re-arranged comment lines.
- Arrange driver code in more readable format[1]

[1]  http://patchwork.ozlabs.org/patch/265683/

Signed-off-by: Jagan Teki <jteki@openedev.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>

spi: xilinx_spi: Move header code to driver

Move the header code into driver for more readable and
easy to access it.

Signed-off-by: Jagan Teki <jteki@openedev.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>

spi: Zap oc_tiny_spi driver

Zap oc_tiny_spi driver since the boards used this driver
is no longer been active.

Signed-off-by: Jagan Teki <jteki@openedev.com>
Cc: Thomas Chou <thomas@wytron.com.tw>

spi: Zap ftssp010_spi driver

Zap ftssp010_spi driver since the boards used this driver
is no longer been active.

Signed-off-by: Jagan Teki <jteki@openedev.com>
Cc: Kuo-Jung Su <dantesu@faraday-tech.com>
Cc: Axel Lin <axel.lin@ingics.com>

spi: Zap andes_spi driver

Zap andes_spi driver since the boards used this driver
is no longer been active.

Signed-off-by: Jagan Teki <jteki@openedev.com>
Cc: Macpaul Lin <macpaul@andestech.com>

board: axs103 - add maintainer information

Looks like I forgot to add myself as a maintainer for AXS103 defconfig.
Fixing this now.

Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Tom Rini <trini@konsulko.com>

arc: significant cache rework

[1] Align cache management functions to those in Linux kernel. I.e.:
    a) Use the same functions for all cache ops (D$ Inv/Flush)
    b) Split cache ops in 3 sub-functions: "before", "lineloop" and
"after". That way we may re-use "before" and "after" functions for
region and full cache ops.

 [2] Implement full-functional L2 (SLC) management. Before SLC was
simply disabled early on boot. It's also possible to enable or disable
L2 cache from config utility.

 [3] Disable/enable corresponding caches early on boot. So if U-Boot is
configured to use caches they will be used at all times (this is useful
in partucular for speed-up of relocation).

Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>

arc: implement slave cores kick-start for Linux kernel

With new SMP-enabled CPUs with ARC HS38 cores and corresponding support
in Linux kernel it's required to add basic SMP support in U-Boot.

Currently we assume the one and only core starts execution after
power-on. So most of things in U-Boot is handled in UP mode.

But when U-Boot is used for loading and starting Linux kernel right
before jumping to kernel's entry point U-Boot:
 [1] Sets all slave cores to jump to the same address [kernel's entry
point]
 [2] Really starts all slav cores

In ARC's implemetation of SMP in Linux kernel all cores are supposed to
run the same start-up code. But only core with ID 0 (master core)
processes further while others are looping waiting for master core to
complete some initialization.

That means it's safe to un-pause slave cores and let them execute kernel
- they will wait for master anyway.

Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Vineet Gupta <vgupta@synopsys.com>

Prepare v2015.07-rc3

Signed-off-by: Tom Rini <trini@konsulko.com>

sf: update sst25wf040b flash params

sst25wf040b doesn't support Auto Address Increment Programming command.
Remove SST_WR flag.

Signed-off-by: Haikun Wang <B53464@freescale.com>
Tested-by: Haikun Wang <haikun.wang@freescale.com>
Reviewed-by: Jagannadh Teki <jteki@openedev.com>

mtd, spi: Check if flash pointer is used

If flash pointer is used free it, before probing a new
flash and storing it in flash.

Signed-off-by: Heiko Schocher <hs@denx.de>
Tested-by: Jagannadh Teki <jteki@openedev.com>
Reviewed-by: Jagannadh Teki <jteki@openedev.com>

spi, sf: Use offset and size in sf cmd from mtdpartition

With this patch, it is possible to get the offset and size information
from the mtdpartiton setting in "mtdparts", similiar to the
"nand" commandos.

=> sf
sf - SPI flash sub-system

Usage:
sf probe [[bus:]cs] [hz] [mode] - init flash device on given SPI bus
                                  and chip select
sf read addr offset|partition len       - read `len' bytes starting at
                                          `offset' to memory at `addr'
sf write addr offset|partition len      - write `len' bytes from memory
                                          at `addr' to flash at `offset'
sf erase offset|partition [+]len        - erase `len' bytes from `offset'
                                          `+len' round up `len' to block size
sf update addr offset|partition len     - erase and write `len' bytes from memory
                                          at `addr' to flash at `offset'
=>
for example "env" is defined in mtdparts:

=> sf read 13000000 env
device 0 offset 0xd0000, size 0x10000
SF: 65536 bytes @ 0xd0000 Read: OK

zynq-uboot> mtdparts add nor0 0x10000@0x0 env
zynq-uboot> sf erase env 0x10000
SF: 65536 bytes @ 0x0 Erased: OK

zynq-uboot> sf write 0x100 env
device 0 offset 0x0, size 0x10000
SF: 65536 bytes @ 0x0 Written: OK

zynq-uboot> sf read 0x40000 env
device 0 offset 0x0, size 0x10000
SF: 65536 bytes @ 0x0 Read: OK

Signed-off-by: Heiko Schocher <hs@denx.de>
Tested-by: Jagannadh Teki <jteki@openedev.com>
Reviewed-by: Jagannadh Teki <jteki@openedev.com>

mtd, nand: Move common functions from cmd_nand.c to common place

Move common functions from cmd_nand.c (for calculating offset
and size from cmdline paramter) to common place, so they could
used from other commands which use mtd partitions.

For onenand the arg_off_size() is left in common/cmd_onenand.c.
It should use now the common arg_off() function, but as I could
not test onenand I let it there ...

Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: Jagannadh Teki <jteki@openedev.com>

mtd, spi: Add MTD layer driver

Add MTD layer driver for spi, original patch from:
http://git.denx.de/?p=u-boot/u-boot-mips.git;a=commitdiff;h=bb246819cdc90493dd7089eaa51b9e639765cced

Changes from Heiko Schocher against this patch:
- Remove compile error if not defining CONFIG_SPI_FLASH_MTD:

  LD      drivers/mtd/spi/built-in.o
drivers/mtd/spi/sf_probe.o: In function `spi_flash_mtd_unregister':
/home/hs/abb/imx6/u-boot/drivers/mtd/spi/sf_internal.h:168: multiple definition of `spi_flash_mtd_unregister'
drivers/mtd/spi/sf_params.o:/home/hs/abb/imx6/u-boot/drivers/mtd/spi/sf_internal.h:168: first defined here
drivers/mtd/spi/sf_ops.o: In function `spi_flash_mtd_unregister':
/home/hs/abb/imx6/u-boot/drivers/mtd/spi/sf_internal.h:168: multiple definition of `spi_flash_mtd_unregister'
drivers/mtd/spi/sf_params.o:/home/hs/abb/imx6/u-boot/drivers/mtd/spi/sf_internal.h:168: first defined here
make[1]: *** [drivers/mtd/spi/built-in.o] Fehler 1
make: *** [drivers/mtd/spi] Fehler 2

- Add a README entry.
- Add correct writebufsize, to fit with Linux v3.14
  MTD, UBI/UBIFS sync.

Note (From Jagan): For testing raw mtd parition erase/read/write operations
using cmd_sf, sf_mtd should be required to register the spi flash device to
MTD layer but the sf_mtd_info ops were not required until and unless if we
use any flash filesystem layer say for example UBI. Due to this the foot-print
got increased ~290bytes in non-UBI case here that should be acceptible.

Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
Tested-by: Jagannadh Teki <jteki@openedev.com>
Reviewed-by: Jagannadh Teki <jteki@openedev.com>

defconfig: ls1021a: Add OF_CONTROL and DM support

PI and QSPI only work when boot from QSPI on ls1021a.
This patch only enable options in qspi boot defconfig.

Signed-off-by: Haikun Wang <haikun.wang@freescale.com>
Tested-by: Haikun Wang <haikun.wang@freescale.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>