mfd: lpc_sch: Partially revert "Add support for Intel Quark X1000"

[ Upstream commit 922e8ce883e59b52786b2c11656d84dc58ef084a ]

The IRQ support for SCH GPIO is not specific to the Intel Quark SoC.
Moreover the IRQ routing is quite interesting there, so while it's
needs a special support, the driver haven't it anyway yet.

Due to above remove basically redundant code of IRQ support.

This reverts commit ec689a8a8155ce8b966bd5d7737a3916f5e48be3.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

bnxt_en: Fix possible unintended driver initiated error recovery

[ Upstream commit 1b2b91831983aeac3adcbb469aa8b0dc71453f89 ]

If error recovery is already enabled, bnxt_timer() will periodically
check the heartbeat register and the reset counter.  If we get an
error recovery async. notification from the firmware (e.g. change in
primary/secondary role), we will immediately read and update the
heartbeat register and the reset counter.  If the timer for the next
health check expires soon after this, we may read the heartbeat register
again in quick succession and find that it hasn't changed.  This will
trigger error recovery unintentionally.

The likelihood is small because we also reset fw_health->tmr_counter
which will reset the interval for the next health check.  But the
update is not protected and bnxt_timer() can miss the update and
perform the health check without waiting for the full interval.

Fix it by only reading the heartbeat register and reset counter in
bnxt_async_event_process() if error recovery is trasitioning to the
enabled state.  Also add proper memory barriers so that when enabling
for the first time, bnxt_timer() will see the tmr_counter interval and
perform the health check after the full interval has elapsed.

Fixes: 7e914027f757 ("bnxt_en: Enable health monitoring.")
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

bnxt_en: Improve logging of error recovery settings information.

[ Upstream commit f4d95c3c194de04ae7b44f850131321c7ceb9312 ]

We currently only log the error recovery settings if it is enabled.
In some cases, firmware disables error recovery after it was
initially enabled.  Without logging anything, the user will not be
aware of this change in setting.

Log it when error recovery is disabled.  Also, change the reset count
value from hexadecimal to decimal.

Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

bnxt_en: Convert to use netif_level() helpers.

[ Upstream commit 871127e6ab0d6abb904cec81fc022baf6953be1f ]

Use the various netif_level() helpers to simplify the C code.  This was
suggested by Joe Perches.

Cc: Joe Perches <joe@perches.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/1611642024-3166-1-git-send-email-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

bnxt_en: Consolidate firmware reset event logging.

[ Upstream commit 5863b10aa86a5f5f69a25b55a5c15806c834471a ]

Combine the three netdev_warn() calls into a single call, printed at
the NETIF_MSG_HW log level.

Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

bnxt_en: log firmware debug notifications

[ Upstream commit a44daa8fcbcf572545c4c1a7908b3fbb38388048 ]

Firmware is capable of generating asynchronous debug notifications.
The event data is opaque to the driver and is simply logged. Debug
notifications can be enabled by turning on hardware status messages
using the ethtool msglvl interface.

Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

bnxt_en: Fix asic.rev in devlink dev info command

[ Upstream commit 6fdab8a3ade2adc123bbf5c4fdec3394560b1fb1 ]

The current asic.rev is incomplete and does not include the metal
revision.  Add the metal revision and decode the complete asic
revision into the more common and readable form (A0, B0, etc).

Fixes: 7154917a12b2 ("bnxt_en: Refactor bnxt_dl_info_get().")
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

bnxt_en: fix stored FW_PSID version masks

[ Upstream commit 1656db67233e4259281d2ac35b25f712edbbc20b ]

The FW_PSID version components are 8 bits wide, not 4.

Fixes: db28b6c77f40 ("bnxt_en: Fix devlink info's stored fw.psid version format.")
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: dsa: b53: Fix IMP port setup on BCM5301x

[ Upstream commit 63f8428b4077de3664eb0b252393c839b0b293ec ]

Broadcom's b53 switches have one IMP (Inband Management Port) that needs
to be programmed using its own designed register. IMP port may be
different than CPU port - especially on devices with multiple CPU ports.

For that reason it's required to explicitly note IMP port index and
check for it when choosing a register to use.

This commit fixes BCM5301x support. Those switches use CPU port 5 while
their IMP port is 8. Before this patch b53 was trying to program port 5
with B53_PORT_OVERRIDE_CTRL instead of B53_GMII_PORT_OVERRIDE_CTRL(5).

It may be possible to also replace "cpu_port" usages with
dsa_is_cpu_port() but that is out of the scope of thix BCM5301x fix.

Fixes: 967dd82ffc52 ("net: dsa: b53: Add support for Broadcom RoboSwitch")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ip_gre: validate csum_start only on pull

[ Upstream commit 8a0ed250f911da31a2aef52101bc707846a800ff ]

The GRE tunnel device can pull existing outer headers in ipge_xmit.
This is a rare path, apparently unique to this device. The below
commit ensured that pulling does not move skb->data beyond csum_start.

But it has a false positive if ip_summed is not CHECKSUM_PARTIAL and
thus csum_start is irrelevant.

Refine to exclude this. At the same time simplify and strengthen the
test.

Simplify, by moving the check next to the offending pull, making it
more self documenting and removing an unnecessary branch from other
code paths.

Strengthen, by also ensuring that the transport header is correct and
therefore the inner headers will be after skb_reset_inner_headers.
The transport header is set to csum_start in skb_partial_csum_set.

Link: https://lore.kernel.org/netdev/YS+h%2FtqCJJiQei+W@shredder/
Fixes: 1d011c4803c7 ("ip_gre: add validation for csum_start")
Reported-by: Ido Schimmel <idosch@idosch.org>
Suggested-by: Alexander Duyck <alexander.duyck@gmail.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

qlcnic: Remove redundant unlock in qlcnic_pinit_from_rom

[ Upstream commit 9ddbc2a00d7f63fa9748f4278643193dac985f2d ]

Previous commit 68233c583ab4 removes the qlcnic_rom_lock()
in qlcnic_pinit_from_rom(), but remains its corresponding
unlock function, which is odd. I'm not very sure whether the
lock is missing, or the unlock is redundant. This bug is
suggested by a static analysis tool, please advise.

Fixes: 68233c583ab4 ("qlcnic: updated reset sequence")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

fq_codel: reject silly quantum parameters

[ Upstream commit c7c5e6ff533fe1f9afef7d2fa46678987a1335a7 ]

syzbot found that forcing a big quantum attribute would crash hosts fast,
essentially using this:

tc qd replace dev eth0 root fq_codel quantum 4294967295

This is because fq_codel_dequeue() would have to loop
~2^31 times in :

if (flow->deficit <= 0) {
flow->deficit += q->quantum;
list_move_tail(&flow->flowchain, &q->old_flows);
goto begin;
}

SFQ max quantum is 2^19 (half a megabyte)
Lets adopt a max quantum of one megabyte for FQ_CODEL.

Fixes: 4b549a2ef4be ("fq_codel: Fair Queue Codel AQM")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

netfilter: socket: icmp6: fix use-after-scope

[ Upstream commit 730affed24bffcd1eebd5903171960f5ff9f1f22 ]

Bug reported by KASAN:

BUG: KASAN: use-after-scope in inet6_ehashfn (net/ipv6/inet6_hashtables.c:40)
Call Trace:
(...)
inet6_ehashfn (net/ipv6/inet6_hashtables.c:40)
(...)
nf_sk_lookup_slow_v6 (net/ipv6/netfilter/nf_socket_ipv6.c:91
net/ipv6/netfilter/nf_socket_ipv6.c:146)

It seems that this bug has already been fixed by Eric Dumazet in the
past in:
commit 78296c97ca1f ("netfilter: xt_socket: fix a stack corruption bug")

But a variant of the same issue has been introduced in
commit d64d80a2cde9 ("netfilter: x_tables: don't extract flow keys on early demuxed sks in socket match")

`daddr` and `saddr` potentially hold a reference to ipv6_var that is no
longer in scope when the call to `nf_socket_get_sock_v6` is made.

Fixes: d64d80a2cde9 ("netfilter: x_tables: don't extract flow keys on early demuxed sks in socket match")
Acked-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Benjamin Hesmans <benjamin.hesmans@tessares.net>
Reviewed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: dsa: b53: Set correct number of ports in the DSA struct

[ Upstream commit d12e1c4649883e8ca5e8ff341e1948b3b6313259 ]

Setting DSA_MAX_PORTS caused DSA to call b53 callbacks (e.g.
b53_disable_port() during dsa_register_switch()) for invalid
(non-existent) ports. That made b53 modify unrelated registers and is
one of reasons for a broken BCM5301x support.

This problem exists for years but DSA_MAX_PORTS usage has changed few
times. It seems the most accurate to reference commit dropping
dsa_switch_alloc() in the Fixes tag.

Fixes: 7e99e3470172 ("net: dsa: remove dsa_switch_alloc helper")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: dsa: b53: Fix calculating number of switch ports

[ Upstream commit cdb067d31c0fe4cce98b9d15f1f2ef525acaa094 ]

It isn't true that CPU port is always the last one. Switches BCM5301x
have 9 ports (port 6 being inactive) and they use port 5 as CPU by
default (depending on design some other may be CPU ports too).

A more reliable way of determining number of ports is to check for the
last set bit in the "enabled_ports" bitfield.

This fixes b53 internal state, it will allow providing accurate info to
the DSA and is required to fix BCM5301x support.

Fixes: 967dd82ffc52 ("net: dsa: b53: Add support for Broadcom RoboSwitch")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: hso: add failure handler for add_net_device

[ Upstream commit ecdc28defc46af476566fffd9e5cb4495a2f176e ]

If the network devices connected to the system beyond
HSO_MAX_NET_DEVICES. add_net_device() in hso_create_net_device()
will be failed for the network_table is full. It will lead to
business failure which rely on network_table, for example,
hso_suspend() and hso_resume(). It will also lead to memory leak
because resource release process can not search the hso_device
object from network_table in hso_free_interface().

Add failure handler for add_net_device() in hso_create_net_device()
to solve the above problems.

Fixes: 72dc1c096c70 ("HSO: add option hso driver")
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

selftests: mptcp: clean tmp files in simult_flows

[ Upstream commit bfd862a7e9318dd906844807a713d27cdd1a72b1 ]

'$cin' and '$sin' variables are local to a function: they are then not
available from the cleanup trap.

Instead, we need to use '$large' and '$small' that are not local and
defined just before setting the trap.

Without this patch, running this script in a loop might cause a:

  write: No space left on device

issue.

Fixes: 1a418cb8e888 ("mptcp: simult flow self-tests")
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: dsa: tag_rtl4_a: Fix egress tags

[ Upstream commit 0e90dfa7a8d817db755c7b5d89d77b9c485e4180 ]

I noticed that only port 0 worked on the RTL8366RB since we
started to use custom tags.

It turns out that the format of egress custom tags is actually
different from ingress custom tags. While the lower bits just
contain the port number in ingress tags, egress tags need to
indicate destination port by setting the bit for the
corresponding port.

It was working on port 0 because port 0 added 0x00 as port
number in the lower bits, and if you do this the packet appears
at all ports, including the intended port. Ooops.

Fix this and all ports work again. Use the define for shifting
the "type A" into place while we're at it.

Tested on the D-Link DIR-685 by sending traffic to each of
the ports in turn. It works.

Fixes: 86dd9868b878 ("net: dsa: tag_rtl4_a: Support also egress tags")
Cc: DENG Qingfang <dqfext@gmail.com>
Cc: Mauri Sandberg <sandberg@mailfence.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

gpio: mpc8xxx: Use 'devm_gpiochip_add_data()' to simplify the code and avoid a leak

[ Upstream commit 889a1b3f35db6ba5ba6a0c23a3a55594570b6a17 ]

If an error occurs after a 'gpiochip_add_data()' call it must be undone by
a corresponding 'gpiochip_remove()' as already done in the remove function.

To simplify the code a fix a leak in the error handling path of the probe,
use the managed version instead (i.e. 'devm_gpiochip_add_data()')

Fixes: 698b8eeaed72 ("gpio/mpc8xxx: change irq handler from chained to normal")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

gpio: mpc8xxx: Fix a resources leak in the error handling path of 'mpc8xxx_probe()'

[ Upstream commit 555bda42b0c1a5ffb72d3227c043e8afde778f1f ]

Commit 698b8eeaed72 ("gpio/mpc8xxx: change irq handler from chained to normal")
has introduced a new 'goto err;' at the very end of the function, but has
not updated the error handling path accordingly.

Add the now missing 'irq_domain_remove()' call which balances a previous
'irq_domain_create_linear() call.

Fixes: 698b8eeaed72 ("gpio/mpc8xxx: change irq handler from chained to normal")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

perf bench inject-buildid: Handle writen() errors

[ Upstream commit edf7b4a2d85e37a1ee77156bddaed4aa6af9c5e1 ]

The build on fedora:35 and fedora:rawhide with clang is failing with:

  49    41.00 fedora:35                     : FAIL clang version 13.0.0 (Fedora 13.0.0~rc1-1.fc35)
    bench/inject-buildid.c:351:6: error: variable 'len' set but not used [-Werror,-Wunused-but-set-variable]
            u64 len = 0;
                ^
    1 error generated.
    make[3]: *** [/git/perf-5.14.0-rc7/tools/build/Makefile.build:139: bench] Error 2
  50    41.11 fedora:rawhide                : FAIL clang version 13.0.0 (Fedora 13.0.0~rc1-1.fc35)
    bench/inject-buildid.c:351:6: error: variable 'len' set but not used [-Werror,-Wunused-but-set-variable]
            u64 len = 0;
                ^
    1 error generated.
    make[3]: *** [/git/perf-5.14.0-rc7/tools/build/Makefile.build:139: bench] Error 2

That 'len' variable is not used at all, so just make sure all the
synthesize_RECORD() routines return ssize_t to propagate the writen()
return, as it may fail, ditch the 'ret' var and bail out if those
routines fail.

Fixes: 0bf02a0d80427f26 ("perf bench: Add build-id injection benchmark")
Acked-by: Namhyung Kim <namhyung@kernel.org>
Link: http://lore.kernel.org/lkml/CAM9d7cgEZNSor+B+7Y2C+QYGme_v5aH0Zn0RLfxoQ+Fy83EHrg@mail.gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

perf unwind: Do not overwrite FEATURE_CHECK_LDFLAGS-libunwind-{x86,aarch64}

[ Upstream commit cdf32b44678c382a31dc183d9a767306915cda7b ]

When setting LIBUNWIND_DIR, we first set

 FEATURE_CHECK_LDFLAGS-libunwind-{aarch64,x86} = -L$(LIBUNWIND_DIR)/lib.

<committer note>
This happens a bit before, the overwritting, in:

  libunwind_arch_set_flags = $(eval $(libunwind_arch_set_flags_code))
  define libunwind_arch_set_flags_code
    FEATURE_CHECK_CFLAGS-libunwind-$(1)  = -I$(LIBUNWIND_DIR)/include
    FEATURE_CHECK_LDFLAGS-libunwind-$(1) = -L$(LIBUNWIND_DIR)/lib
  endef

  ifdef LIBUNWIND_DIR
    LIBUNWIND_CFLAGS  = -I$(LIBUNWIND_DIR)/include
    LIBUNWIND_LDFLAGS = -L$(LIBUNWIND_DIR)/lib
    LIBUNWIND_ARCHS = x86 x86_64 arm aarch64 debug-frame-arm debug-frame-aarch64
    $(foreach libunwind_arch,$(LIBUNWIND_ARCHS),$(call libunwind_arch_set_flags,$(libunwind_arch)))
  endif

Look at that 'foreach' on all the LIBUNWIND_ARCHS.
</>

After commit 5c4d7c82c0dc ("perf unwind: Do not put libunwind-{x86,aarch64}
in FEATURE_TESTS_BASIC"), FEATURE_CHECK_LDFLAGS-libunwind-{x86,aarch64} is
overwritten. As a result, the remote libunwind libraries cannot be searched
from $(LIBUNWIND_DIR)/lib directory during feature check tests. Fix it with
variable appending.

Before this patch:

  perf$ make VF=1 LIBUNWIND_DIR=/opt/libunwind_aarch64
   BUILD:   Doing 'make -j16' parallel build
  <SNIP>
  ...
  ...                    libopencsd: [ OFF ]
  ...                 libunwind-x86: [ OFF ]
  ...              libunwind-x86_64: [ OFF ]
  ...                 libunwind-arm: [ OFF ]
  ...             libunwind-aarch64: [ OFF ]
  ...         libunwind-debug-frame: [ OFF ]
  ...     libunwind-debug-frame-arm: [ OFF ]
  ... libunwind-debug-frame-aarch64: [ OFF ]
  ...                           cxx: [ OFF ]
  <SNIP>

  perf$ cat ../build/feature/test-libunwind-aarch64.make.output
  /usr/bin/ld: cannot find -lunwind-aarch64
  /usr/bin/ld: cannot find -lunwind-aarch64
  collect2: error: ld returned 1 exit status

After this patch:

  perf$ make VF=1 LIBUNWIND_DIR=/opt/libunwind_aarch64
   BUILD:   Doing 'make -j16' parallel build
  <SNIP>
  ...                    libopencsd: [ OFF ]
  ...                 libunwind-x86: [ OFF ]
  ...              libunwind-x86_64: [ OFF ]
  ...                 libunwind-arm: [ OFF ]
  ...             libunwind-aarch64: [ on  ]
  ...         libunwind-debug-frame: [ OFF ]
  ...     libunwind-debug-frame-arm: [ OFF ]
  ... libunwind-debug-frame-aarch64: [ OFF ]
  ...                           cxx: [ OFF ]
  <SNIP>

  perf$ cat ../build/feature/test-libunwind-aarch64.make.output

  perf$ ldd ./perf
        linux-vdso.so.1 (0x00007ffdf07da000)
        libpthread.so.0 => /lib/x86_64-linux-gnu/libpthread.so.0 (0x00007f30953dc000)
        librt.so.1 => /lib/x86_64-linux-gnu/librt.so.1 (0x00007f30951d4000)
        libm.so.6 => /lib/x86_64-linux-gnu/libm.so.6 (0x00007f3094e36000)
        libdl.so.2 => /lib/x86_64-linux-gnu/libdl.so.2 (0x00007f3094c32000)
        libelf.so.1 => /usr/lib/x86_64-linux-gnu/libelf.so.1 (0x00007f3094a18000)
        libdw.so.1 => /usr/lib/x86_64-linux-gnu/libdw.so.1 (0x00007f30947cc000)
        libunwind-x86_64.so.8 => /usr/lib/x86_64-linux-gnu/libunwind-x86_64.so.8 (0x00007f30945ad000)
        libunwind.so.8 => /usr/lib/x86_64-linux-gnu/libunwind.so.8 (0x00007f3094392000)
        liblzma.so.5 => /lib/x86_64-linux-gnu/liblzma.so.5 (0x00007f309416c000)
        libunwind-aarch64.so.8 => not found
        libslang.so.2 => /lib/x86_64-linux-gnu/libslang.so.2 (0x00007f3093c8a000)
        libpython2.7.so.1.0 => /usr/local/lib/libpython2.7.so.1.0 (0x00007f309386b000)
        libz.so.1 => /lib/x86_64-linux-gnu/libz.so.1 (0x00007f309364e000)
        libnuma.so.1 => /usr/lib/x86_64-linux-gnu/libnuma.so.1 (0x00007f3093443000)
        libc.so.6 => /lib/x86_64-linux-gnu/libc.so.6 (0x00007f3093052000)
        /lib64/ld-linux-x86-64.so.2 (0x00007f3096097000)
        libbz2.so.1.0 => /lib/x86_64-linux-gnu/libbz2.so.1.0 (0x00007f3092e42000)
        libutil.so.1 => /lib/x86_64-linux-gnu/libutil.so.1 (0x00007f3092c3f000)

Fixes: 5c4d7c82c0dceccf ("perf unwind: Do not put libunwind-{x86,aarch64} in FEATURE_TESTS_BASIC")
Signed-off-by: Li Huafei <lihuafei1@huawei.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: He Kuang <hekuang@huawei.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Zhang Jinhao <zhangjinhao2@huawei.com>
Link: http://lore.kernel.org/lkml/20210823134340.60955-1-lihuafei1@huawei.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARC: export clear_user_page() for modules

[ Upstream commit 6b5ff0405e4190f23780362ea324b250bc495683 ]

0day bot reports a build error:
  ERROR: modpost: "clear_user_page" [drivers/media/v4l2-core/videobuf-dma-sg.ko] undefined!
so export it in arch/arc/ to fix the build error.

In most ARCHes, clear_user_page() is a macro. OTOH, in a few
ARCHes it is a function and needs to be exported.
PowerPC exported it in 2004. It looks like nds32 and nios2
still need to have it exported.

Fixes: 4102b53392d63 ("ARC: [mm] Aliasing VIPT dcache support 2/4")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: linux-snps-arc@lists.infradead.org
Signed-off-by: Vineet Gupta <vgupta@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

mtd: rawnand: cafe: Fix a resource leak in the error handling path of 'cafe_nand_probe()'

[ Upstream commit 6b430c7595e4eb95fae8fb54adc3c3ce002e75ae ]

A successful 'init_rs_non_canonical()' call should be balanced by a
corresponding 'free_rs()' call in the error handling path of the probe, as
already done in the remove function.

Update the error handling path accordingly.

Fixes: 8c61b7a7f4d4 ("[MTD] [NAND] Use rslib for CAFÉ ECC")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/fd313d3fb787458bcc73189e349f481133a2cdc9.1629532640.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Sasha Levin <sashal@kernel.org>

PCI: Sync __pci_register_driver() stub for CONFIG_PCI=n

[ Upstream commit 817f9916a6e96ae43acdd4e75459ef4f92d96eb1 ]

The CONFIG_PCI=y case got a new parameter long time ago.  Sync the stub as
well.

[bhelgaas: add parameter names]
Fixes: 725522b5453d ("PCI: add the sysfs driver name to all modules")
Link: https://lore.kernel.org/r/20210813153619.89574-1-andriy.shevchenko@linux.intel.com
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

KVM: arm64: Handle PSCI resets before userspace touches vCPU state

[ Upstream commit 6826c6849b46aaa91300201213701eb861af4ba0 ]

The CPU_ON PSCI call takes a payload that KVM uses to configure a
destination vCPU to run. This payload is non-architectural state and not
exposed through any existing UAPI. Effectively, we have a race between
CPU_ON and userspace saving/restoring a guest: if the target vCPU isn't
ran again before the VMM saves its state, the requested PC and context
ID are lost. When restored, the target vCPU will be runnable and start
executing at its old PC.

We can avoid this race by making sure the reset payload is serviced
before userspace can access a vCPU's state.

Fixes: 358b28f09f0a ("arm/arm64: KVM: Allow a VCPU to fully reset itself")
Signed-off-by: Oliver Upton <oupton@google.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210818202133.1106786-3-oupton@google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

KVM: arm64: Fix read-side race on updates to vcpu reset state

[ Upstream commit 6654f9dfcb88fea3b9affc180dc3c04333d0f306 ]

KVM correctly serializes writes to a vCPU's reset state, however since
we do not take the KVM lock on the read side it is entirely possible to
read state from two different reset requests.

Cure the race for now by taking the KVM lock when reading the
reset_state structure.

Fixes: 358b28f09f0a ("arm/arm64: KVM: Allow a VCPU to fully reset itself")
Signed-off-by: Oliver Upton <oupton@google.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210818202133.1106786-2-oupton@google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

mtd: mtdconcat: Check _read, _write callbacks existence before assignment

[ Upstream commit a89d69a44e282be95ae76125dddc79515541efeb ]

Since 2431c4f5b46c3 ("mtd: Implement mtd_{read,write}() as wrappers
around mtd_{read,write}_oob()") don't allow _write|_read and
_write_oob|_read_oob existing at the same time, we should check the
existence of callbacks "_read and _write" from subdev's master device
(We can trust master device since it has been registered) before
assigning, otherwise following warning occurs while making
concatenated device:

  WARNING: CPU: 2 PID: 6728 at drivers/mtd/mtdcore.c:595
  add_mtd_device+0x7f/0x7b0

Fixes: 2431c4f5b46c3 ("mtd: Implement mtd_{read,write}() around ...")
Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210817114857.2784825-3-chengzhihao1@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

mtd: mtdconcat: Judge callback existence based on the master

[ Upstream commit f9e109a209a8e01e16f37e1252304f1eb3908be4 ]

Since commit 46b5889cc2c5("mtd: implement proper partition handling")
applied, mtd partition device won't hold some callback functions, such
as _block_isbad, _block_markbad, etc. Besides, function mtd_block_isbad()
will get mtd device's master mtd device, then invokes master mtd device's
callback function. So, following process may result mtd_block_isbad()
always return 0, even though mtd device has bad blocks:

1. Split a mtd device into 3 partitions: PA, PB, PC
[ Each mtd partition device won't has callback function _block_isbad(). ]
2. Concatenate PA and PB as a new mtd device PN
[ mtd_concat_create() finds out each subdev has no callback function
_block_isbad(), so PN won't be assigned callback function
concat_block_isbad(). ]
Then, mtd_block_isbad() checks "!master->_block_isbad" is true, will
always return 0.

Reproducer:
// reproduce.c
static int __init init_diy_module(void)
{
struct mtd_info *mtd[2];
struct mtd_info *mtd_combine = NULL;

mtd[0] = get_mtd_device_nm("NAND simulator partition 0");
if (!mtd[0]) {
pr_err("cannot find mtd1\n");
return -EINVAL;
}
mtd[1] = get_mtd_device_nm("NAND simulator partition 1");
if (!mtd[1]) {
pr_err("cannot find mtd2\n");
return -EINVAL;
}

put_mtd_device(mtd[0]);
put_mtd_device(mtd[1]);

mtd_combine = mtd_concat_create(mtd, 2, "Combine mtd");
if (mtd_combine == NULL) {
pr_err("combine failed\n");
return -EINVAL;
}

mtd_device_register(mtd_combine, NULL, 0);
pr_info("Combine success\n");

return 0;
}

1. ID="0x20,0xac,0x00,0x15"
2. modprobe nandsim id_bytes=$ID parts=50,100 badblocks=100
3. insmod reproduce.ko
4. flash_erase /dev/mtd3 0 0
  libmtd: error!: MEMERASE64 ioctl failed for eraseblock 100 (mtd3)
  error 5 (Input/output error)
  // Should be "flash_erase: Skipping bad block at 00c80000"

Fixes: 46b5889cc2c54bac ("mtd: implement proper partition handling")
Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210817114857.2784825-2-chengzhihao1@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

tracing/boot: Fix a hist trigger dependency for boot time tracing

[ Upstream commit 6fe7c745f2acb73e4cc961d7f91125eef5a8861f ]

Fixes a build error when CONFIG_HIST_TRIGGERS=n with boot-time
tracing. Since the trigger_process_regex() is defined only
when CONFIG_HIST_TRIGGERS=y, if it is disabled, the 'actions'
event option also must be disabled.

Link: https://lkml.kernel.org/r/162856123376.203126.582144262622247352.stgit@devnote2
Fixes: 81a59555ff15 ("tracing/boot: Add per-event settings")
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

mfd: tqmx86: Clear GPIO IRQ resource when no IRQ is set

[ Upstream commit a946506c48f3bd09363c9d2b0a178e55733bcbb6 ]

The driver was registering IRQ 0 when no IRQ was set. This leads to
warnings with newer kernels.

Clear the resource flags, so no resource is registered at all in this
case.

Fixes: 2f17dd34ffed ("mfd: tqmx86: IO controller with I2C, Wachdog and GPIO")
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

PCI: Fix pci_dev_str_match_path() alloc while atomic bug

[ Upstream commit 7eb6ea4148579b85540a41d57bcec315b8af8ff8 ]

pci_dev_str_match_path() is often called with a spinlock held so the
allocation has to be atomic.  The call tree is:

  pci_specified_resource_alignment() <-- takes spin_lock();
    pci_dev_str_match()
      pci_dev_str_match_path()

Fixes: 45db33709ccc ("PCI: Allow specifying devices using a base bus and path of devfns")
Link: https://lore.kernel.org/r/20210812070004.GC31863@kili
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

KVM: arm64: Restrict IPA size to maximum 48 bits on 4K and 16K page size

[ Upstream commit 5e5df9571c319fb107d7a523cc96fcc99961ee70 ]

Even though ID_AA64MMFR0.PARANGE reports 52 bit PA size support, it cannot
be enabled as guest IPA size on 4K or 16K page size configurations. Hence
kvm_ipa_limit must be restricted to 48 bits. This change achieves required
IPA capping.

Before the commit c9b69a0cf0b4 ("KVM: arm64: Don't constrain maximum IPA
size based on host configuration"), the problem here would have been just
latent via PHYS_MASK_SHIFT (which earlier in turn capped kvm_ipa_limit),
which remains capped at 48 bits on 4K and 16K configs.

Cc: Marc Zyngier <maz@kernel.org>
Cc: James Morse <james.morse@arm.com>
Cc: Alexandru Elisei <alexandru.elisei@arm.com>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: kvmarm@lists.cs.columbia.edu
Cc: linux-kernel@vger.kernel.org
Fixes: c9b69a0cf0b4 ("KVM: arm64: Don't constrain maximum IPA size based on host configuration")
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/1628680275-16578-1-git-send-email-anshuman.khandual@arm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

netfilter: nft_ct: protect nft_ct_pcpu_template_refcnt with mutex

[ Upstream commit e3245a7b7b34bd2e97f744fd79463add6e9d41f4 ]

Syzbot hit use-after-free in nf_tables_dump_sets. The problem was in
missing lock protection for nft_ct_pcpu_template_refcnt.

Before commit f102d66b335a ("netfilter: nf_tables: use dedicated
mutex to guard transactions") all transactions were serialized by global
mutex, but then global mutex was changed to local per netnamespace
commit_mutex.

This change causes use-after-free bug, when 2 netnamespaces concurently
changing nft_ct_pcpu_template_refcnt without proper locking. Fix it by
adding nft_ct_pcpu_mutex and protect all nft_ct_pcpu_template_refcnt
changes with it.

Fixes: f102d66b335a ("netfilter: nf_tables: use dedicated mutex to guard transactions")
Reported-and-tested-by: syzbot+649e339fa6658ee623d3@syzkaller.appspotmail.com
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

netfilter: Fix fall-through warnings for Clang

[ Upstream commit c2168e6bd7ec50cedb69b3be1ba6146e28893c69 ]

In preparation to enable -Wimplicit-fallthrough for Clang, fix multiple
warnings by explicitly adding multiple break statements instead of just
letting the code fall through to the next case.

Link: https://github.com/KSPP/linux/issues/115
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

PCI: iproc: Fix BCMA probe resource handling

[ Upstream commit aeaea8969b402e0081210cc9144404d13996efed ]

In commit 7ef1c871da16 ("PCI: iproc: Use
pci_parse_request_of_pci_ranges()"), calling
devm_request_pci_bus_resources() was dropped from the common iProc
probe code, but is still needed for BCMA bus probing. Without it, there
will be lots of warnings like this:

pci 0000:00:00.0: BAR 8: no space for [mem size 0x00c00000]
pci 0000:00:00.0: BAR 8: failed to assign [mem size 0x00c00000]

Add back calling devm_request_pci_bus_resources() and adding the
resources to pci_host_bridge.windows for BCMA bus probe.

Link: https://lore.kernel.org/r/20210803215656.3803204-2-robh@kernel.org
Fixes: 7ef1c871da16 ("PCI: iproc: Use pci_parse_request_of_pci_ranges()")
Reported-by: Rafał Miłecki <zajec5@gmail.com>
Tested-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Srinath Mannam <srinath.mannam@broadcom.com>
Cc: Roman Bacik <roman.bacik@broadcom.com>
Cc: Bharat Gooty <bharat.gooty@broadcom.com>
Cc: Abhishek Shah <abhishek.shah@broadcom.com>
Cc: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Cc: Ray Jui <ray.jui@broadcom.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: BCM Kernel Feedback <bcm-kernel-feedback-list@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: "Krzysztof Wilczyński" <kw@linux.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

PCI: of: Don't fail devm_pci_alloc_host_bridge() on missing 'ranges'

[ Upstream commit d277f6e88c88729b1d57d40bbfb00d0bfc961972 ]

Commit 669cbc708122 ("PCI: Move DT resource setup into
devm_pci_alloc_host_bridge()") made devm_pci_alloc_host_bridge() fail on
any DT resource parsing errors, but Broadcom iProc uses
devm_pci_alloc_host_bridge() on BCMA bus devices that don't have DT
resources. In particular, there is no 'ranges' property. Fix iProc by
making 'ranges' optional.

If 'ranges' is required by a platform, there's going to be more errors
latter on if it is missing.

Link: https://lore.kernel.org/r/20210803215656.3803204-1-robh@kernel.org
Fixes: 669cbc708122 ("PCI: Move DT resource setup into devm_pci_alloc_host_bridge()")
Reported-by: Rafał Miłecki <zajec5@gmail.com>
Tested-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Srinath Mannam <srinath.mannam@broadcom.com>
Cc: Roman Bacik <roman.bacik@broadcom.com>
Cc: Bharat Gooty <bharat.gooty@broadcom.com>
Cc: Abhishek Shah <abhishek.shah@broadcom.com>
Cc: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Cc: Ray Jui <ray.jui@broadcom.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: BCM Kernel Feedback <bcm-kernel-feedback-list@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

backlight: ktd253: Stabilize backlight

[ Upstream commit daa37361518bf2d1f591bbdaa7c68b2a43d7af48 ]

Remove interrupt disablement during backlight setting. It is
way to dangerous and makes platforms instable by having it
miss vblank IRQs leading to the graphics derailing.

The code is using ndelay() which is not available on
platforms such as ARM and will result in 32 * udelay(1)
which is substantial.

Add some code to detect if an interrupt occurs during the
tight loop and in that case just redo it from the top.

Fixes: 5317f37e48b9 ("backlight: Add Kinetic KTD253 backlight driver")
Cc: Stephan Gerhold <stephan@gerhold.net>
Reported-by: newbyte@disroot.org
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

mfd: axp20x: Update AXP288 volatile ranges

[ Upstream commit f949a9ebce7a18005266b859a17f10c891bb13d7 ]

On Cherry Trail devices with an AXP288 PMIC the external SD-card slot
used the AXP's DLDO2 as card-voltage and either DLDO3 or GPIO1LDO
(GPIO1 pin in low noise LDO mode) as signal-voltage.

These regulators are turned on/off and in case of the signal-voltage
also have their output-voltage changed by the _PS0 and _PS3 power-
management ACPI methods on the MMC-controllers ACPI fwnode as well as
by the _DSM ACPI method for changing the signal voltage.

The AML code implementing these methods is directly accessing the
PMIC through ACPI I2C OpRegion accesses, instead of using the special
PMIC OpRegion handled by drivers/acpi/pmic/intel_pmic_xpower.c .

This means that the contents of the involved PMIC registers can change
without the change being made through the regmap interface, so regmap
should not cache the contents of these registers.

Mark the regulator power on/off, the regulator voltage control and the
GPIO1 control registers as volatile, to avoid regmap caching them.

Specifically this fixes an issue on some models where the i915 driver
toggles another LDO using the same on/off register on/off through
MIPI sequences (through intel_soc_pmic_exec_mipi_pmic_seq_element())
which then writes back a cached on/off register-value where the
card-voltage is off causing the external sdcard slot to stop working
when the screen goes blank, or comes back on again.

The regulator register-range now marked volatile also includes the
buck regulator control registers. This is done on purpose these are
normally not touched by the AML code, but they are updated directly
by the SoC's PUNIT which means that they may also change without going
through regmap.

Note the AXP288 PMIC is only used on Bay- and Cherry-Trail platforms,
so even though this is an ACPI specific problem there is no need to
make the new volatile ranges conditional since these platforms always
use ACPI.

Fixes: dc91c3b6fe66 ("mfd: axp20x: Mark AXP20X_VBUS_IPSOUT_MGMT as volatile")
Fixes: cd53216625a0 ("mfd: axp20x: Fix axp288 volatile ranges")
Reported-and-tested-by: Clamshell <clamfly@163.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

s390/bpf: Fix branch shortening during codegen pass

commit 1511df6f5e9ef32826f20db2ee81f8527154dc14 upstream.

EMIT6_PCREL() macro assumes that the previous pass generated 6 bytes
of code, which is not the case if branch shortening took place. Fix by
using jit->prg, like all the other EMIT6_PCREL_*() macros.

Reported-by: Johan Almbladh <johan.almbladh@anyfinetworks.com>
Fixes: 4e9b4a6883dd ("s390/bpf: Use relative long branches")
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

s390/bpf: Fix 64-bit subtraction of the -0x80000000 constant

commit 6e61dc9da0b7a0d91d57c2e20b5ea4fd2d4e7e53 upstream.

The JIT uses agfi for subtracting constants, but -(-0x80000000) cannot
be represented as a 32-bit signed binary integer. Fix by using algfi in
this particular case.

Reported-by: Johan Almbladh <johan.almbladh@anyfinetworks.com>
Fixes: 054623105728 ("s390/bpf: Add s390x eBPF JIT compiler backend")
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

s390/bpf: Fix optimizing out zero-extensions

commit db7bee653859ef7179be933e7d1384644f795f26 upstream.

Currently the JIT completely removes things like `reg32 += 0`,
however, the BPF_ALU semantics requires the target register to be
zero-extended in such cases.

Fix by optimizing out only the arithmetic operation, but not the
subsequent zero-extension.

Reported-by: Johan Almbladh <johan.almbladh@anyfinetworks.com>
Fixes: 054623105728 ("s390/bpf: Add s390x eBPF JIT compiler backend")
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

NTB: perf: Fix an error code in perf_setup_inbuf()

[ Upstream commit 0097ae5f7af5684f961a5f803ff7ad3e6f933668 ]

When the function IS_ALIGNED() returns false, the value of ret is 0.
So, we set ret to -EINVAL to indicate this error.

Clean up smatch warning:
drivers/ntb/test/ntb_perf.c:602 perf_setup_inbuf() warn: missing error
code 'ret'.

Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Sasha Levin <sashal@kernel.org>

NTB: Fix an error code in ntb_msit_probe()

[ Upstream commit 319f83ac98d7afaabab84ce5281a819a358b9895 ]

When the value of nm->isr_ctx is false, the value of ret is 0.
So, we set ret to -ENOMEM to indicate this error.

Clean up smatch warning:
drivers/ntb/test/ntb_msi_test.c:373 ntb_msit_probe() warn: missing
error code 'ret'.

Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ethtool: Fix an error code in cxgb2.c

[ Upstream commit 7db8263a12155c7ae4ad97e850f1e499c73765fc ]

When adapter->registered_device_map is NULL, the value of err is
uncertain, we set err to -EINVAL to avoid ambiguity.

Clean up smatch warning:
drivers/net/ethernet/chelsio/cxgb/cxgb2.c:1114 init_one() warn: missing
error code 'err'

Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

PCI: ibmphp: Fix double unmap of io_mem

[ Upstream commit faa2e05ad0dccf37f995bcfbb8d1980d66c02c11 ]

ebda_rsrc_controller() calls iounmap(io_mem) on the error path. Its caller,
ibmphp_access_ebda(), also calls iounmap(io_mem) on good and error paths.

Remove the iounmap(io_mem) invocation from ebda_rsrc_controller().

[bhelgaas: remove item from TODO]
Link: https://lore.kernel.org/r/20210818165751.591185-1-os.vaslot@gmail.com
Signed-off-by: Vishal Aslot <os.vaslot@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

block, bfq: honor already-setup queue merges

[ Upstream commit 2d52c58b9c9bdae0ca3df6a1eab5745ab3f7d80b ]

The function bfq_setup_merge prepares the merging between two
bfq_queues, say bfqq and new_bfqq. To this goal, it assigns
bfqq->new_bfqq = new_bfqq. Then, each time some I/O for bfqq arrives,
the process that generated that I/O is disassociated from bfqq and
associated with new_bfqq (merging is actually a redirection). In this
respect, bfq_setup_merge increases new_bfqq->ref in advance, adding
the number of processes that are expected to be associated with
new_bfqq.

Unfortunately, the stable-merging mechanism interferes with this
setup. After bfqq->new_bfqq has been set by bfq_setup_merge, and
before all the expected processes have been associated with
bfqq->new_bfqq, bfqq may happen to be stably merged with a different
queue than the current bfqq->new_bfqq. In this case, bfqq->new_bfqq
gets changed. So, some of the processes that have been already
accounted for in the ref counter of the previous new_bfqq will not be
associated with that queue.  This creates an unbalance, because those
references will never be decremented.

This commit fixes this issue by reestablishing the previous, natural
behaviour: once bfqq->new_bfqq has been set, it will not be changed
until all expected redirections have occurred.

Signed-off-by: Davide Zini <davidezini2@gmail.com>
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
Link: https://lore.kernel.org/r/20210802141352.74353-2-paolo.valente@linaro.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: usb: cdc_mbim: avoid altsetting toggling for Telit LN920

[ Upstream commit aabbdc67f3485b5db27ab4eba01e5fbf1ffea62c ]

Add quirk CDC_MBIM_FLAG_AVOID_ALTSETTING_TOGGLE for Telit LN920
0x1061 composition in order to avoid bind error.

Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

Set fc_nlinfo in nh_create_ipv4, nh_create_ipv6

[ Upstream commit 9aca491e0dccf8a9d84a5b478e5eee3c6ea7803b ]

This patch fixes kernel NULL pointer dereference when creating nexthop
which is bound with SRv6 decapsulation. In the creation of nexthop,
__seg6_end_dt_vrf_build is called. __seg6_end_dt_vrf_build expects
fc_lninfo in fib6_config is set correctly, but it isn't set in
nh_create_ipv6, which causes kernel crash.

Here is steps to reproduce kernel crash:

1. modprobe vrf
2. ip -6 nexthop add encap seg6local action End.DT4 vrftable 1 dev eth0

We got the following message:

[  901.370336] BUG: kernel NULL pointer dereference, address: 0000000000000ba0
[  901.371658] #PF: supervisor read access in kernel mode
[  901.372672] #PF: error_code(0x0000) - not-present page
[  901.373672] PGD 0 P4D 0
[  901.374248] Oops: 0000 [#1] SMP PTI
[  901.374944] CPU: 0 PID: 8593 Comm: ip Not tainted 5.14-051400-generic #202108310811-Ubuntu
[  901.376404] Hardware name: Red Hat KVM, BIOS 1.11.1-4.module_el8.2.0+320+13f867d7 04/01/2014
[  901.377907] RIP: 0010:vrf_ifindex_lookup_by_table_id+0x19/0x90 [vrf]
[  901.379182] Code: c1 e9 72 ff ff ff e8 96 49 01 c2 66 0f 1f 44 00 00 0f 1f 44 00 00 55 48 89 e5 41 56 41 55 41 89 f5 41 54 53 8b 05 47 4c 00 00 <48> 8b 97 a0 0b 00 00 48 8b 1c c2 e8 57 27 53 c1 4c 8d a3 88 00 00
[  901.382652] RSP: 0018:ffffbf2d02043590 EFLAGS: 00010282
[  901.383746] RAX: 000000000000000b RBX: ffff990808255e70 RCX: ffffbf2d02043aa8
[  901.385436] RDX: 0000000000000001 RSI: 0000000000000001 RDI: 0000000000000000
[  901.386924] RBP: ffffbf2d020435b0 R08: 00000000000000c0 R09: ffff990808255e40
[  901.388537] R10: ffffffff83b08c90 R11: 0000000000000009 R12: 0000000000000000
[  901.389937] R13: 0000000000000001 R14: 0000000000000000 R15: 000000000000000b
[  901.391226] FS:  00007fe49381f740(0000) GS:ffff99087dc00000(0000) knlGS:0000000000000000
[  901.392737] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  901.393803] CR2: 0000000000000ba0 CR3: 000000000e3e8003 CR4: 0000000000770ef0
[  901.395122] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[  901.396496] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[  901.397833] PKRU: 55555554
[  901.398578] Call Trace:
[  901.399144]  l3mdev_ifindex_lookup_by_table_id+0x3b/0x70
[  901.400179]  __seg6_end_dt_vrf_build+0x34/0xd0
[  901.401067]  seg6_end_dt4_build+0x16/0x20
[  901.401904]  seg6_local_build_state+0x271/0x430
[  901.402797]  lwtunnel_build_state+0x81/0x130
[  901.403645]  fib_nh_common_init+0x82/0x100
[  901.404465]  ? sock_def_readable+0x4b/0x80
[  901.405285]  fib6_nh_init+0x115/0x7c0
[  901.406033]  nh_create_ipv6.isra.0+0xe1/0x140
[  901.406932]  rtm_new_nexthop+0x3b7/0xeb0
[  901.407828]  rtnetlink_rcv_msg+0x152/0x3a0
[  901.408663]  ? rtnl_calcit.isra.0+0x130/0x130
[  901.409535]  netlink_rcv_skb+0x55/0x100
[  901.410319]  rtnetlink_rcv+0x15/0x20
[  901.411026]  netlink_unicast+0x1a8/0x250
[  901.411813]  netlink_sendmsg+0x238/0x470
[  901.412602]  ? _copy_from_user+0x2b/0x60
[  901.413394]  sock_sendmsg+0x65/0x70
[  901.414112]  ____sys_sendmsg+0x218/0x290
[  901.414929]  ? copy_msghdr_from_user+0x5c/0x90
[  901.415814]  ___sys_sendmsg+0x81/0xc0
[  901.416559]  ? fsnotify_destroy_marks+0x27/0xf0
[  901.417447]  ? call_rcu+0xa4/0x230
[  901.418153]  ? kmem_cache_free+0x23f/0x410
[  901.418972]  ? dentry_free+0x37/0x70
[  901.419705]  ? mntput_no_expire+0x4c/0x260
[  901.420574]  __sys_sendmsg+0x62/0xb0
[  901.421297]  __x64_sys_sendmsg+0x1f/0x30
[  901.422057]  do_syscall_64+0x5c/0xc0
[  901.422756]  ? syscall_exit_to_user_mode+0x27/0x50
[  901.423675]  ? __x64_sys_close+0x12/0x40
[  901.424462]  ? do_syscall_64+0x69/0xc0
[  901.425219]  ? irqentry_exit_to_user_mode+0x9/0x20
[  901.426149]  ? irqentry_exit+0x19/0x30
[  901.426901]  ? exc_page_fault+0x89/0x160
[  901.427709]  ? asm_exc_page_fault+0x8/0x30
[  901.428536]  entry_SYSCALL_64_after_hwframe+0x44/0xae
[  901.429514] RIP: 0033:0x7fe493945747
[  901.430248] Code: 64 89 02 48 c7 c0 ff ff ff ff eb bb 0f 1f 80 00 00 00 00 f3 0f 1e fa 64 8b 04 25 18 00 00 00 85 c0 75 10 b8 2e 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 51 c3 48 83 ec 28 89 54 24 1c 48 89 74 24 10
[  901.433549] RSP: 002b:00007ffe9932cf68 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
[  901.434981] RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007fe493945747
[  901.436303] RDX: 0000000000000000 RSI: 00007ffe9932cfe0 RDI: 0000000000000003
[  901.437607] RBP: 00000000613053f7 R08: 0000000000000001 R09: 00007ffe9932d07c
[  901.438990] R10: 000055f4a903a010 R11: 0000000000000246 R12: 0000000000000001
[  901.440340] R13: 0000000000000001 R14: 000055f4a802b163 R15: 000055f4a8042020
[  901.441630] Modules linked in: vrf nls_utf8 isofs nls_iso8859_1 dm_multipath scsi_dh_rdac scsi_dh_emc scsi_dh_alua intel_rapl_msr intel_rapl_common isst_if_mbox_msr isst_if_common nfit rapl input_leds joydev serio_raw qemu_fw_cfg mac_hid sch_fq_codel drm virtio_rng ip_tables x_tables autofs4 btrfs blake2b_generic zstd_compress raid10 raid456 async_raid6_recov async_memcpy async_pq async_xor async_tx xor raid6_pq libcrc32c raid1 raid0 multipath linear crct10dif_pclmul crc32_pclmul ghash_clmulni_intel aesni_intel crypto_simd virtio_net net_failover cryptd psmouse virtio_blk failover i2c_piix4 pata_acpi floppy
[  901.450808] CR2: 0000000000000ba0
[  901.451514] ---[ end trace c27b934b99ade304 ]---
[  901.452403] RIP: 0010:vrf_ifindex_lookup_by_table_id+0x19/0x90 [vrf]
[  901.453626] Code: c1 e9 72 ff ff ff e8 96 49 01 c2 66 0f 1f 44 00 00 0f 1f 44 00 00 55 48 89 e5 41 56 41 55 41 89 f5 41 54 53 8b 05 47 4c 00 00 <48> 8b 97 a0 0b 00 00 48 8b 1c c2 e8 57 27 53 c1 4c 8d a3 88 00 00
[  901.456910] RSP: 0018:ffffbf2d02043590 EFLAGS: 00010282
[  901.457912] RAX: 000000000000000b RBX: ffff990808255e70 RCX: ffffbf2d02043aa8
[  901.459238] RDX: 0000000000000001 RSI: 0000000000000001 RDI: 0000000000000000
[  901.460552] RBP: ffffbf2d020435b0 R08: 00000000000000c0 R09: ffff990808255e40
[  901.461882] R10: ffffffff83b08c90 R11: 0000000000000009 R12: 0000000000000000
[  901.463208] R13: 0000000000000001 R14: 0000000000000000 R15: 000000000000000b
[  901.464529] FS:  00007fe49381f740(0000) GS:ffff99087dc00000(0000) knlGS:0000000000000000
[  901.466058] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  901.467189] CR2: 0000000000000ba0 CR3: 000000000e3e8003 CR4: 0000000000770ef0
[  901.468515] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[  901.469858] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[  901.471139] PKRU: 55555554

Signed-off-by: Ryoga Saito <contact@proelbtn.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

octeontx2-af: Add additional register check to rvu_poll_reg()

[ Upstream commit 21274aa1781941884599a97ab59be7f8f36af98c ]

Check one more time before exiting the API with an error.
Fix API to poll at least twice, in case there are other high priority
tasks and this API doesn't get CPU cycles for multiple jiffies update.

In addition, increase timeout from usecs_to_jiffies(10000) to
usecs_to_jiffies(20000), to prevent the case that for CONFIG_100HZ
timeout will be a single jiffies.
A single jiffies results actual timeout that can be any time between
1usec and 10msec. To solve this, a value of usecs_to_jiffies(20000)
ensures that timeout is 2 jiffies.

Signed-off-by: Smadar Fuks <smadarf@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

watchdog: Start watchdog in watchdog_set_last_hw_keepalive only if appropriate

[ Upstream commit dbe80cf471f940db3063197b7adb1169f89be9ed ]

We must not pet a running watchdog when handle_boot_enabled is off
because this will kick off automatic triggering before userland is
running, defeating the purpose of the handle_boot_enabled control.
Furthermore, don't ping in case watchdog_set_last_hw_keepalive was
called incorrectly when the hardware watchdog is actually not running.

Fixed: cef9572e9af3 ("watchdog: add support for adjusting last known HW keepalive time")
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/93d56386-6e37-060b-55ce-84de8cde535f@web.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

PCI: Add ACS quirks for Cavium multi-function devices

[ Upstream commit 32837d8a8f63eb95dcb9cd005524a27f06478832 ]

Some Cavium endpoints are implemented as multi-function devices without ACS
capability, but they actually don't support peer-to-peer transactions.

Add ACS quirks to declare DMA isolation for the following devices:

  - BGX device found on Octeon-TX (8xxx)
  - CGX device found on Octeon-TX2 (9xxx)
  - RPM device found on Octeon-TX3 (10xxx)

Link: https://lore.kernel.org/r/20210810122425.1115156-1-george.cherian@marvell.com
Signed-off-by: George Cherian <george.cherian@marvell.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

PCI: j721e: Add PCIe support for AM64

[ Upstream commit c8a375a8e15ac31293d7fda08008d6da8f5df3db ]

AM64 has the same PCIe IP as in J7200 with certain erratas not
applicable (quirk_detect_quiet_flag). Add support for "ti,am64-pcie-host"
compatible and "ti,am64-pcie-ep" compatible that is specific to AM64.

Link: https://lore.kernel.org/r/20210811123336.31357-5-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

PCI: j721e: Add PCIe support for J7200

[ Upstream commit f1de58802f0fff364cf49f5e47d1be744baa434f ]

J7200 has the same PCIe IP as in J721E with minor changes in the
wrapper. J7200 allows byte access of bridge configuration space
registers and the register field for LINK_DOWN interrupt is different.
J7200 also requires "quirk_detect_quiet_flag" to be set. Configure these
changes as part of driver data applicable only to J7200.

Link: https://lore.kernel.org/r/20210811123336.31357-4-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

PCI: cadence: Add quirk flag to set minimum delay in LTSSM Detect.Quiet state

[ Upstream commit 09c24094b2e3a15ef3fc44f54a191b3db522fb11 ]

PCIe fails to link up if SERDES lanes not used by PCIe are assigned to
another protocol. For example, link training fails if lanes 2 and 3 are
assigned to another protocol while lanes 0 and 1 are used for PCIe to
form a two lane link. This failure is due to an incorrect tie-off on an
internal status signal indicating electrical idle.

Status signals going from SERDES to PCIe Controller are tied-off when a
lane is not assigned to PCIe. Signal indicating electrical idle is
incorrectly tied-off to a state that indicates non-idle. As a result,
PCIe sees unused lanes to be out of electrical idle and this causes
LTSSM to exit Detect.Quiet state without waiting for 12ms timeout to
occur. If a receiver is not detected on the first receiver detection
attempt in Detect.Active state, LTSSM goes back to Detect.Quiet and
again moves forward to Detect.Active state without waiting for 12ms as
required by PCIe base specification. Since wait time in Detect.Quiet is
skipped, multiple receiver detect operations are performed back-to-back
without allowing time for capacitance on the transmit lines to
discharge. This causes subsequent receiver detection to always fail even
if a receiver gets connected eventually.

Add a quirk flag "quirk_detect_quiet_flag" to program the minimum
time the LTSSM should wait on entering Detect.Quiet state here.
This has to be set for J7200 as it has an incorrect tie-off on unused
lanes.

Link: https://lore.kernel.org/r/20210811123336.31357-3-kishon@ti.com
Signed-off-by: Nadeem Athani <nadeem@cadence.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

PCI: cadence: Use bitfield for *quirk_retrain_flag* instead of bool

[ Upstream commit f4455748b2126a9ba2bcc9cfb2fbcaa08de29bb2 ]

No functional change. As we are intending to add additional 1-bit
members in struct j721e_pcie_data/struct cdns_pcie_rc, use bitfields
instead of bool since it takes less space. As discussed in [1],
the preference is to use bitfileds instead of bool inside structures.

[1] -> https://lore.kernel.org/linux-fsdevel/CA+55aFzKQ6Pj18TB8p4Yr0M4t+S+BsiHH=BJNmn=76-NcjTj-g@mail.gmail.com/

Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20210811123336.31357-2-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

tracing/probes: Reject events which have the same name of existing one

[ Upstream commit 8e242060c6a4947e8ae7d29794af6a581db08841 ]

Since kprobe_events and uprobe_events only check whether the
other same-type probe event has the same name or not, if the
user gives the same name of the existing tracepoint event (or
the other type of probe events), it silently fails to create
the tracefs entry (but registered.) as below.

/sys/kernel/tracing # ls events/task/task_rename
enable   filter   format   hist     id       trigger
/sys/kernel/tracing # echo p:task/task_rename vfs_read >> kprobe_events
[  113.048508] Could not create tracefs 'task_rename' directory
/sys/kernel/tracing # cat kprobe_events
p:task/task_rename vfs_read

To fix this issue, check whether the existing events have the
same name or not in trace_probe_register_event_call(). If exists,
it rejects to register the new event.

Link: https://lkml.kernel.org/r/162936876189.187130.17558311387542061930.stgit@devnote2
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

PCI: rcar: Fix runtime PM imbalance in rcar_pcie_ep_probe()

[ Upstream commit 1e29cd9983eba1b596bc07f94d81d728007f8a25 ]

pm_runtime_get_sync() will increase the runtime PM counter
even it returns an error. Thus a pairing decrement is needed
to prevent refcount leak. Fix this by replacing this API with
pm_runtime_resume_and_get(), which will not change the runtime
PM counter on error.

Link: https://lore.kernel.org/r/20210408072402.15069-1-dinghao.liu@zju.edu.cn
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sasha Levin <sashal@kernel.org>

mfd: Don't use irq_create_mapping() to resolve a mapping

[ Upstream commit 9ff80e2de36d0554e3a6da18a171719fe8663c17 ]

Although irq_create_mapping() is able to deal with duplicate
mappings, it really isn't supposed to be a substitute for
irq_find_mapping(), and can result in allocations that take place
in atomic context if the mapping didn't exist.

Fix the handful of MFD drivers that use irq_create_mapping() in
interrupt context by using irq_find_mapping() instead.

Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

PCI: tegra: Fix OF node reference leak

[ Upstream commit eff21f5da308265678e7e59821795e606f3e560f ]

Commit 9e38e690ace3 ("PCI: tegra: Fix OF node reference leak") has fixed
some node reference leaks in this function but missed some of them.

In fact, having 'port' referenced in the 'rp' structure is not enough to
prevent the leak, until 'rp' is actually added in the 'pcie->ports' list.

Add the missing 'goto err_node_put' accordingly.

Link: https://lore.kernel.org/r/55b11e9a7fa2987fbc0869d68ae59888954d65e2.1620148539.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

PCI: tegra194: Fix MSI-X programming

[ Upstream commit 43537cf7e351264a1f05ed42ad402942bfc9140e ]

Lower order MSI-X address is programmed in MSIX_ADDR_MATCH_HIGH_OFF
DBI register instead of higher order address. This patch fixes this
programming mistake.

Link: https://lore.kernel.org/r/20210623100525.19944-3-omp@nvidia.com
Signed-off-by: Om Prakash Singh <omp@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

PCI: tegra194: Fix handling BME_CHGED event

[ Upstream commit ceb1412c1c8ca5b28c4252bdb15f2f1f17b4a1b0 ]

In tegra_pcie_ep_hard_irq(), APPL_INTR_STATUS_L0 is stored in val and again
APPL_INTR_STATUS_L1_0_0 is also stored in val. So when execution reaches
"if (val & APPL_INTR_STATUS_L0_PCI_CMD_EN_INT)", val is not correct.

Link: https://lore.kernel.org/r/20210623100525.19944-2-omp@nvidia.com
Signed-off-by: Om Prakash Singh <omp@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

fuse: fix use after free in fuse_read_interrupt()

[ Upstream commit e1e71c168813564be0f6ea3d6740a059ca42d177 ]

There is a potential race between fuse_read_interrupt() and
fuse_request_end().

TASK1
  in fuse_read_interrupt(): delete req->intr_entry (while holding
  fiq->lock)

TASK2
  in fuse_request_end(): req->intr_entry is empty -> skip fiq->lock
  wake up TASK3

TASK3
  request is freed

TASK1
  in fuse_read_interrupt(): dereference req->in.h.unique ***BAM***

Fix by always grabbing fiq->lock if the request was ever interrupted
(FR_INTERRUPTED set) thereby serializing with concurrent
fuse_read_interrupt() calls.

FR_INTERRUPTED is set before the request is queued on fiq->interrupts.
Dequeing the request is done with list_del_init() but FR_INTERRUPTED is not
cleared in this case.

Reported-by: lijiazi <lijiazi@xiaomi.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

PCI: Add ACS quirks for NXP LX2xx0 and LX2xx2 platforms

[ Upstream commit d08c8b855140e9f5240b3ffd1b8b9d435675e281 ]

Root Ports in NXP LX2xx0 and LX2xx2, where each Root Port is a Root Complex
with unique segment numbers, do provide isolation features to disable peer
transactions and validate bus numbers in requests, but do not provide an
actual PCIe ACS capability.

Add ACS quirks for NXP LX2xx0 A/C/E/N and LX2xx2 A/C/E/N platforms.

  LX2xx0A : without security features + CAN-FD
    LX2160A (0x8d81) - 16 cores
    LX2120A (0x8da1) - 12 cores
    LX2080A (0x8d83) -  8 cores

  LX2xx0C : security features + CAN-FD
    LX2160C (0x8d80) - 16 cores
    LX2120C (0x8da0) - 12 cores
    LX2080C (0x8d82) -  8 cores

  LX2xx0E : security features + CAN
    LX2160E (0x8d90) - 16 cores
    LX2120E (0x8db0) - 12 cores
    LX2080E (0x8d92) -  8 cores

  LX2xx0N : without security features + CAN
    LX2160N (0x8d91) - 16 cores
    LX2120N (0x8db1) - 12 cores
    LX2080N (0x8d93) -  8 cores

  LX2xx2A : without security features + CAN-FD
    LX2162A (0x8d89) - 16 cores
    LX2122A (0x8da9) - 12 cores
    LX2082A (0x8d8b) -  8 cores

  LX2xx2C : security features + CAN-FD
    LX2162C (0x8d88) - 16 cores
    LX2122C (0x8da8) - 12 cores
    LX2082C (0x8d8a) -  8 cores

  LX2xx2E : security features + CAN
    LX2162E (0x8d98) - 16 cores
    LX2122E (0x8db8) - 12 cores
    LX2082E (0x8d9a) -  8 cores

  LX2xx2N : without security features + CAN
    LX2162N (0x8d99) - 16 cores
    LX2122N (0x8db9) - 12 cores
    LX2082N (0x8d9b) -  8 cores

[bhelgaas: put PCI_VENDOR_ID_NXP definition next to PCI_VENDOR_ID_FREESCALE
as a clue that they share the same Device ID namespace]
Link: https://lore.kernel.org/r/20210729121747.1823086-1-wasim.khan@oss.nxp.com
Link: https://lore.kernel.org/r/20210803180021.3252886-1-wasim.khan@oss.nxp.com
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

mfd: db8500-prcmu: Adjust map to reality

[ Upstream commit ec343111c056ec3847800302f6dbc57281f833fa ]

These are the actual frequencies reported by the PLL, so let's
report these. The roundoffs are inappropriate, we should round
to the frequency that the clock will later report.

Drop some whitespace at the same time.

Cc: phone-devel@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

dt-bindings: mtd: gpmc: Fix the ECC bytes vs. OOB bytes equation

[ Upstream commit 778cb8e39f6ec252be50fc3850d66f3dcbd5dd5a ]

"PAGESIZE / 512" is the number of ECC chunks.
"ECC_BYTES" is the number of bytes needed to store a single ECC code.
"2" is the space reserved by the bad block marker.

"2 + (PAGESIZE / 512) * ECC_BYTES" should of course be lower or equal
than the total number of OOB bytes, otherwise it won't fit.

Fix the equation by substituting s/>=/<=/.

Suggested-by: Ryan J. Barnett <ryan.barnett@collins.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/linux-mtd/20210610143945.3504781-1-miquel.raynal@bootlin.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

mm/memory_hotplug: use "unsigned long" for PFN in zone_for_pfn_range()

commit 7cf209ba8a86410939a24cb1aeb279479a7e0ca6 upstream.

Patch series "mm/memory_hotplug: preparatory patches for new online policy and memory"

These are all cleanups and one fix previously sent as part of [1]:
[PATCH v1 00/12] mm/memory_hotplug: "auto-movable" online policy and memory
groups.

These patches make sense even without the other series, therefore I pulled
them out to make the other series easier to digest.

[1] https://lkml.kernel.org/r/20210607195430.48228-1-david@redhat.com

This patch (of 4):

Checkpatch complained on a follow-up patch that we are using "unsigned"
here, which defaults to "unsigned int" and checkpatch is correct.

As we will search for a fitting zone using the wrong pfn, we might end
up onlining memory to one of the special kernel zones, such as ZONE_DMA,
which can end badly as the onlined memory does not satisfy properties of
these zones.

Use "unsigned long" instead, just as we do in other places when handling
PFNs.  This can bite us once we have physical addresses in the range of
multiple TB.

Link: https://lkml.kernel.org/r/20210712124052.26491-2-david@redhat.com
Fixes: e5e689302633 ("mm, memory_hotplug: display allowed zones in the preferred ordering")
Signed-off-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Pankaj Gupta <pankaj.gupta@ionos.com>
Reviewed-by: Muchun Song <songmuchun@bytedance.com>
Reviewed-by: Oscar Salvador <osalvador@suse.de>
Cc: David Hildenbrand <david@redhat.com>
Cc: Vitaly Kuznetsov <vkuznets@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Pankaj Gupta <pankaj.gupta.linux@gmail.com>
Cc: Wei Yang <richard.weiyang@linux.alibaba.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Anshuman Khandual <anshuman.khandual@arm.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Mike Rapoport <rppt@kernel.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Len Brown <lenb@kernel.org>
Cc: Pavel Tatashin <pasha.tatashin@soleen.com>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: virtualization@lists.linux-foundation.org
Cc: Andy Lutomirski <luto@kernel.org>
Cc: "Aneesh Kumar K.V" <aneesh.kumar@linux.ibm.com>
Cc: Anton Blanchard <anton@ozlabs.org>
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: Baoquan He <bhe@redhat.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jia He <justin.he@arm.com>
Cc: Joe Perches <joe@perches.com>
Cc: Kefeng Wang <wangkefeng.wang@huawei.com>
Cc: Laurent Dufour <ldufour@linux.ibm.com>
Cc: Michel Lespinasse <michel@lespinasse.org>
Cc: Nathan Lynch <nathanl@linux.ibm.com>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Pierre Morel <pmorel@linux.ibm.com>
Cc: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com>
Cc: Rich Felker <dalias@libc.org>
Cc: Scott Cheloha <cheloha@linux.ibm.com>
Cc: Sergei Trofimovich <slyfox@gentoo.org>
Cc: Thiago Jung Bauermann <bauerman@linux.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Vishal Verma <vishal.l.verma@intel.com>
Cc: Will Deacon <will@kernel.org>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: hns3: fix the timing issue of VF clearing interrupt sources

commit 427900d27d86b820c559037a984bd403f910860f upstream.

Currently, the VF does not clear the interrupt source immediately after
receiving the interrupt. As a result, if the second interrupt task is
triggered when processing the first interrupt task, clearing the
interrupt source before exiting will clear the interrupt sources of the
two tasks at the same time. As a result, no interrupt is triggered for
the second task. The VF detects the missed message only when the next
interrupt is generated.

Clearing it immediately after executing check_evt_cause ensures that:
1. Even if two interrupt tasks are triggered at the same time, they can
be processed.
2. If the second task is triggered during the processing of the first
task and the interrupt source is not cleared, the interrupt is reported
after vector0 is enabled.

Fixes: b90fcc5bd904 ("net: hns3: add reset handling for VF when doing Core/Global/IMP reset")
Signed-off-by: Jiaran Zhang <zhangjiaran@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: hns3: disable mac in flr process

commit b81d8948746520f989e86d66292ff72b5056114a upstream.

The firmware will not disable mac in flr process. Therefore, the driver
needs to proactively disable mac during flr, which is the same as the
function reset.

Fixes: 35d93a30040c ("net: hns3: adjust the process of PF reset")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: hns3: change affinity_mask to numa node range

commit 1dc839ec09d3ab2a4156dc98328b8bc3586f2b70 upstream.

Currently, affinity_mask is set to a single cpu. As a result,
irqbalance becomes invalid in SUBSET or EXACT mode. To solve
this problem, change affinity_mask to numa node range. In this
way, irqbalance can be performed on the cpu of the numa node.

Fixes: 0812545487ec ("net: hns3: add interrupt affinity support for misc interrupt")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: hns3: pad the short tunnel frame before sending to hardware

commit d18e81183b1cb9c309266cbbce9acd3e0c528d04 upstream.

The hardware cannot handle short tunnel frames below 65 bytes,
and will cause vlan tag missing problem. So pads packet size to
65 bytes for tunnel frames to fix this bug.

Fixes: 3db084d28dc0("net: hns3: Fix for vxlan tx checksum bug")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

bnxt_en: make bnxt_free_skbs() safe to call after bnxt_free_mem()

commit 1affc01fdc6035189a5ab2a24948c9419ee0ecf2 upstream.

The call to bnxt_free_mem(..., false) in the bnxt_half_open_nic() error
path will deallocate ring descriptor memory via bnxt_free_?x_rings(),
but because irq_re_init is false, the ring info itself is not freed.

To simplify error paths, deallocation functions have generally been
written to be safe when called on unallocated memory. It should always
be safe to call dev_close(), which calls bnxt_free_skbs() a second time,
even in this semi- allocated ring state.

Calling bnxt_free_skbs() a second time with the rings already freed will
cause NULL pointer dereference.  Fix it by checking the rings are valid
before proceeding in bnxt_free_tx_skbs() and
bnxt_free_one_rx_ring_skbs().

Fixes: 975bc99a4a39 ("bnxt_en: Refactor bnxt_free_rx_skbs().")
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

KVM: PPC: Book3S HV: Tolerate treclaim. in fake-suspend mode changing registers

commit 267cdfa21385d78c794768233678756e32b39ead upstream.

POWER9 DD2.2 and 2.3 hardware implements a "fake-suspend" mode where
certain TM instructions executed in HV=0 mode cause softpatch interrupts
so the hypervisor can emulate them and prevent problematic processor
conditions. In this fake-suspend mode, the treclaim. instruction does
not modify registers.

Unfortunately the rfscv instruction executed by the guest do not
generate softpatch interrupts, which can cause the hypervisor to lose
track of the fake-suspend mode, and it can execute this treclaim. while
not in fake-suspend mode. This modifies GPRs and crashes the hypervisor.

It's not trivial to disable scv in the guest with HFSCR now, because
they assume a POWER9 has scv available. So this fix saves and restores
checkpointed registers across the treclaim.

Fixes: 7854f7545bff ("KVM: PPC: Book3S: Rework TM save/restore code and make it C-callable")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210908101718.118522-2-npiggin@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ibmvnic: check failover_pending in login response

commit 273c29e944bda9a20a30c26cfc34c9a3f363280b upstream.

If a failover occurs before a login response is received, the login
response buffer maybe undefined. Check that there was no failover
before accessing the login response buffer.

Fixes: 032c5e82847a ("Driver for IBM System i/p VNIC protocol")
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dt-bindings: arm: Fix Toradex compatible typo

commit 55c21d57eafb7b379bb7b3e93baf9ca2695895b0 upstream.

Fix board compatible typo reported by dtbs_check.

Fixes: f4d1577e9bc6 ("dt-bindings: arm: Convert Tegra board/soc bindings to json-schema")
Signed-off-by: David Heidelberg <david@ixit.cz>
Link: https://lore.kernel.org/r/20210912165120.188490-1-david@ixit.cz
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

udp_tunnel: Fix udp_tunnel_nic work-queue type

commit e50e711351bdc656a8e6ca1022b4293cae8dcd59 upstream.

Turn udp_tunnel_nic work-queue to an ordered work-queue. This queue
holds the UDP-tunnel configuration commands of the different netdevs.
When the netdevs are functions of the same NIC the order of
execution may be crucial.

Problem example:
NIC with 2 PFs, both PFs declare offload quota of up to 3 UDP-ports.
 $ifconfig eth2 1.1.1.1/16 up

 $ip link add eth2_19503 type vxlan id 5049 remote 1.1.1.2 dev eth2 dstport 19053
 $ip link set dev eth2_19503 up

 $ip link add eth2_19504 type vxlan id 5049 remote 1.1.1.3 dev eth2 dstport 19054
 $ip link set dev eth2_19504 up

 $ip link add eth2_19505 type vxlan id 5049 remote 1.1.1.4 dev eth2 dstport 19055
 $ip link set dev eth2_19505 up

 $ip link add eth2_19506 type vxlan id 5049 remote 1.1.1.5 dev eth2 dstport 19056
 $ip link set dev eth2_19506 up

NIC RX port offload infrastructure offloads the first 3 UDP-ports (on
all devices which sets NETIF_F_RX_UDP_TUNNEL_PORT feature) and not
UDP-port 19056. So both PFs gets this offload configuration.

 $ip link set dev eth2_19504 down

This triggers udp-tunnel-core to remove the UDP-port 19504 from
offload-ports-list and offload UDP-port 19056 instead.

In this scenario it is important that the UDP-port of 19504 will be
removed from both PFs before trying to add UDP-port 19056. The NIC can
stop offloading a UDP-port only when all references are removed.
Otherwise the NIC may report exceeding of the offload quota.

Fixes: cc4e3835eff4 ("udp_tunnel: add central NIC RX port offload infrastructure")
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

qed: Handle management FW error

commit 20e100f52730cd0db609e559799c1712b5f27582 upstream.

Handle MFW (management FW) error response in order to avoid a crash
during recovery flows.

Changes from v1:
- Add "Fixes tag".

Fixes: tag 5e7ba042fd05 ("qed: Fix reading stale configuration information")
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Shai Malin <smalin@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

selftest: net: fix typo in altname test

commit 1b704b27beb11ce147d64b21c914e57afbfb5656 upstream.

If altname deletion of the short alternative name fails, the error
message printed is: "Failed to add short alternative name".
This is obviously a typo, as we are testing altname deletion.

Fix this using a proper error message.

Fixes: f95e6c9c4617 ("selftest: net: add alternative names test")
Signed-off-by: Andrea Claudi <aclaudi@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tcp: fix tp->undo_retrans accounting in tcp_sacktag_one()

commit 4f884f3962767877d7aabbc1ec124d2c307a4257 upstream.

Commit 10d3be569243 ("tcp-tso: do not split TSO packets at retransmit
time") may directly retrans a multiple segments TSO/GSO packet without
split, Since this commit, we can no longer assume that a retransmitted
packet is a single segment.

This patch fixes the tp->undo_retrans accounting in tcp_sacktag_one()
that use the actual segments(pcount) of the retransmitted packet.

Before that commit (10d3be569243), the assumption underlying the
tp->undo_retrans-- seems correct.

Fixes: 10d3be569243 ("tcp-tso: do not split TSO packets at retransmit time")
Signed-off-by: zhenggy <zhenggy@chinatelecom.cn>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

x86/uaccess: Fix 32-bit __get_user_asm_u64() when CC_HAS_ASM_GOTO_OUTPUT=y

commit a69ae291e1cc2d08ae77c2029579c59c9bde5061 upstream.

Commit 865c50e1d279 ("x86/uaccess: utilize CONFIG_CC_HAS_ASM_GOTO_OUTPUT")
added an optimised version of __get_user_asm() for x86 using 'asm goto'.

Like the non-optimised code, the 32-bit implementation of 64-bit
get_user() expands to a pair of 32-bit accesses.  Unlike the
non-optimised code, the _original_ pointer is incremented to copy the
high word instead of loading through a new pointer explicitly
constructed to point at a 32-bit type.  Consequently, if the pointer
points at a 64-bit type then we end up loading the wrong data for the
upper 32-bits.

This was observed as a mount() failure in Android targeting i686 after
b0cfcdd9b967 ("d_path: make 'prepend()' fill up the buffer exactly on
overflow") because the call to copy_from_kernel_nofault() from
prepend_copy() ends up in __get_kernel_nofault() and casts the source
pointer to a 'u64 __user *'.  An attempt to mount at "/debug_ramdisk"
therefore ends up failing trying to mount "/debumdismdisk".

Use the existing '__gu_ptr' source pointer to unsigned int for 32-bit
__get_user_asm_u64() instead of the original pointer.

Cc: Bill Wendling <morbo@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Reported-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes: 865c50e1d279 ("x86/uaccess: utilize CONFIG_CC_HAS_ASM_GOTO_OUTPUT")
Signed-off-by: Will Deacon <will@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Tested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: dsa: destroy the phylink instance on any error in dsa_slave_phy_setup

commit 6a52e73368038f47f6618623d75061dc263b26ae upstream.

DSA supports connecting to a phy-handle, and has a fallback to a non-OF
based method of connecting to an internal PHY on the switch's own MDIO
bus, if no phy-handle and no fixed-link nodes were present.

The -ENODEV error code from the first attempt (phylink_of_phy_connect)
is what triggers the second attempt (phylink_connect_phy).

However, when the first attempt returns a different error code than
-ENODEV, this results in an unbalance of calls to phylink_create and
phylink_destroy by the time we exit the function. The phylink instance
has leaked.

There are many other error codes that can be returned by
phylink_of_phy_connect. For example, phylink_validate returns -EINVAL.
So this is a practical issue too.

Fixes: aab9c4067d23 ("net: dsa: Plug in PHYLINK support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20210914134331.2303380-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net/af_unix: fix a data-race in unix_dgram_poll

commit 04f08eb44b5011493d77b602fdec29ff0f5c6cd5 upstream.

syzbot reported another data-race in af_unix [1]

Lets change __skb_insert() to use WRITE_ONCE() when changing
skb head qlen.

Also, change unix_dgram_poll() to use lockless version
of unix_recvq_full()

It is verry possible we can switch all/most unix_recvq_full()
to the lockless version, this will be done in a future kernel version.

[1] HEAD commit: 8596e589b787732c8346f0482919e83cc9362db1

BUG: KCSAN: data-race in skb_queue_tail / unix_dgram_poll

write to 0xffff88814eeb24e0 of 4 bytes by task 25815 on cpu 0:
 __skb_insert include/linux/skbuff.h:1938 [inline]
 __skb_queue_before include/linux/skbuff.h:2043 [inline]
 __skb_queue_tail include/linux/skbuff.h:2076 [inline]
 skb_queue_tail+0x80/0xa0 net/core/skbuff.c:3264
 unix_dgram_sendmsg+0xff2/0x1600 net/unix/af_unix.c:1850
 sock_sendmsg_nosec net/socket.c:703 [inline]
 sock_sendmsg net/socket.c:723 [inline]
 ____sys_sendmsg+0x360/0x4d0 net/socket.c:2392
 ___sys_sendmsg net/socket.c:2446 [inline]
 __sys_sendmmsg+0x315/0x4b0 net/socket.c:2532
 __do_sys_sendmmsg net/socket.c:2561 [inline]
 __se_sys_sendmmsg net/socket.c:2558 [inline]
 __x64_sys_sendmmsg+0x53/0x60 net/socket.c:2558
 do_syscall_x64 arch/x86/entry/common.c:50 [inline]
 do_syscall_64+0x3d/0x90 arch/x86/entry/common.c:80
 entry_SYSCALL_64_after_hwframe+0x44/0xae

read to 0xffff88814eeb24e0 of 4 bytes by task 25834 on cpu 1:
 skb_queue_len include/linux/skbuff.h:1869 [inline]
 unix_recvq_full net/unix/af_unix.c:194 [inline]
 unix_dgram_poll+0x2bc/0x3e0 net/unix/af_unix.c:2777
 sock_poll+0x23e/0x260 net/socket.c:1288
 vfs_poll include/linux/poll.h:90 [inline]
 ep_item_poll fs/eventpoll.c:846 [inline]
 ep_send_events fs/eventpoll.c:1683 [inline]
 ep_poll fs/eventpoll.c:1798 [inline]
 do_epoll_wait+0x6ad/0xf00 fs/eventpoll.c:2226
 __do_sys_epoll_wait fs/eventpoll.c:2238 [inline]
 __se_sys_epoll_wait fs/eventpoll.c:2233 [inline]
 __x64_sys_epoll_wait+0xf6/0x120 fs/eventpoll.c:2233
 do_syscall_x64 arch/x86/entry/common.c:50 [inline]
 do_syscall_64+0x3d/0x90 arch/x86/entry/common.c:80
 entry_SYSCALL_64_after_hwframe+0x44/0xae

value changed: 0x0000001b -> 0x00000001

Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 25834 Comm: syz-executor.1 Tainted: G        W         5.14.0-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011

Fixes: 86b18aaa2b5b ("skbuff: fix a data race in skb_queue_len()")
Cc: Qian Cai <cai@lca.pw>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

vhost_net: fix OoB on sendmsg() failure.

commit 3c4cea8fa7f71f00c5279547043a84bc2a4d8b8c upstream.

If the sendmsg() call in vhost_tx_batch() fails, both the 'batched_xdp'
and 'done_idx' indexes are left unchanged. If such failure happens
when batched_xdp == VHOST_NET_BATCH, the next call to
vhost_net_build_xdp() will access and write memory outside the xdp
buffers area.

Since sendmsg() can only error with EBADFD, this change addresses the
issue explicitly freeing the XDP buffers batch on error.

Fixes: 0a0be13b8fe2 ("vhost_net: batch submitting XDP buffers to underlayer sockets")
Suggested-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

gen_compile_commands: fix missing 'sys' package

commit ec783c7cb2495c5a3b8ca10db8056d43c528f940 upstream.

We need to import the 'sys' package since the script has called
sys.exit() method.

Fixes: 6ad7cbc01527 ("Makefile: Add clang-tidy and static analyzer support to makefile")
Signed-off-by: Kortan <kortanzh@gmail.com>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: ipa: initialize all filter table slots

commit b5c102238cea985d8126b173d06b9e1de88037ee upstream.

There is an off-by-one problem in ipa_table_init_add(), when
initializing filter tables.

In that function, the number of filter table entries is determined
based on the number of set bits in the filter map.  However that
count does *not* include the extra "slot" in the filter table that
holds the filter map itself.  Meanwhile, ipa_table_addr() *does*
include the filter map in the memory it returns, but because the
count it's provided doesn't include it, it includes one too few
table entries.

Fix this by including the extra slot for the filter map in the count
computed in ipa_table_init_add().

Note: ipa_filter_reset_table() does not have this problem; it resets
filter table entries one by one, but does not overwrite the filter
bitmap.

Fixes: 2b9feef2b6c2 ("soc: qcom: ipa: filter and routing tables")
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

events: Reuse value read using READ_ONCE instead of re-reading it

commit b89a05b21f46150ac10a962aa50109250b56b03b upstream.

In perf_event_addr_filters_apply, the task associated with
the event (event->ctx->task) is read using READ_ONCE at the beginning
of the function, checked, and then re-read from event->ctx->task,
voiding all guarantees of the checks. Reuse the value that was read by
READ_ONCE to ensure the consistency of the task struct throughout the
function.

Fixes: 375637bc52495 ("perf/core: Introduce address range filtering")
Signed-off-by: Baptiste Lepers <baptiste.lepers@gmail.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20210906015310.12802-1-baptiste.lepers@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

nvme-tcp: fix io_work priority inversion

commit 70f437fb4395ad4d1d16fab9a1ad9fbc9fc0579b upstream.

Dispatching requests inline with the .queue_rq() call may block while
holding the send_mutex. If the tcp io_work also happens to schedule, it
may see the req_list is non-empty, leaving "pending" true and remaining
in TASK_RUNNING. Since io_work is of higher scheduling priority, the
.queue_rq task may not get a chance to run, blocking forward progress
and leading to io timeouts.

Instead of checking for pending requests within io_work, let the queueing
restart io_work outside the send_mutex lock if there is more work to be
done.

Fixes: a0fdd1418007f ("nvme-tcp: rerun io_work if req_list is not empty")
Reported-by: Samuel Jones <sjones@kalrayinc.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net/mlx5: Fix potential sleeping in atomic context

commit ee27e330a953595903979ffdb84926843595a9fe upstream.

Fixes the below flow of sleeping in atomic context by releasing
the RCU lock before calling to free_match_list.

build_match_list() <- disables preempt
-> free_match_list()
   -> tree_put_node()
      -> down_write_ref_node() <- take write lock

Fixes: 693c6883bbc4 ("net/mlx5: Add hash table for flow groups in flow table")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Maor Gottlieb <maorg@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net/mlx5: FWTrace, cancel work on alloc pd error flow

commit dfe6fd72b5f1878b16aa2c8603e031bbcd66b96d upstream.

Handle error flow on mlx5_core_alloc_pd() failure,
read_fw_strings_work must be canceled.

Fixes: c71ad41ccb0c ("net/mlx5: FW tracer, events handling")
Reported-by: Pavel Machek (CIP) <pavel@denx.de>
Suggested-by: Pavel Machek (CIP) <pavel@denx.de>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Reviewed-by: Aya Levin <ayal@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

perf machine: Initialize srcline string member in add_location struct

commit 57f0ff059e3daa4e70a811cb1d31a49968262d20 upstream.

It's later supposed to be either a correct address or NULL. Without the
initialization, it may contain an undefined value which results in the
following segmentation fault:

  # perf top --sort comm -g --ignore-callees=do_idle

terminates with:

  #0  0x00007ffff56b7685 in __strlen_avx2 () from /lib64/libc.so.6
  #1  0x00007ffff55e3802 in strdup () from /lib64/libc.so.6
  #2  0x00005555558cb139 in hist_entry__init (callchain_size=<optimized out>, sample_self=true, template=0x7fffde7fb110, he=0x7fffd801c250) at util/hist.c:489
  #3  hist_entry__new (template=template@entry=0x7fffde7fb110, sample_self=sample_self@entry=true) at util/hist.c:564
  #4  0x00005555558cb4ba in hists__findnew_entry (hists=hists@entry=0x5555561d9e38, entry=entry@entry=0x7fffde7fb110, al=al@entry=0x7fffde7fb420,
      sample_self=sample_self@entry=true) at util/hist.c:657
  #5  0x00005555558cba1b in __hists__add_entry (hists=hists@entry=0x5555561d9e38, al=0x7fffde7fb420, sym_parent=<optimized out>, bi=bi@entry=0x0, mi=mi@entry=0x0,
      sample=sample@entry=0x7fffde7fb4b0, sample_self=true, ops=0x0, block_info=0x0) at util/hist.c:288
  #6  0x00005555558cbb70 in hists__add_entry (sample_self=true, sample=0x7fffde7fb4b0, mi=0x0, bi=0x0, sym_parent=<optimized out>, al=<optimized out>, hists=0x5555561d9e38)
      at util/hist.c:1056
  #7  iter_add_single_cumulative_entry (iter=0x7fffde7fb460, al=<optimized out>) at util/hist.c:1056
  #8  0x00005555558cc8a4 in hist_entry_iter__add (iter=iter@entry=0x7fffde7fb460, al=al@entry=0x7fffde7fb420, max_stack_depth=<optimized out>, arg=arg@entry=0x7fffffff7db0)
      at util/hist.c:1231
  #9  0x00005555557cdc9a in perf_event__process_sample (machine=<optimized out>, sample=0x7fffde7fb4b0, evsel=<optimized out>, event=<optimized out>, tool=0x7fffffff7db0)
      at builtin-top.c:842
  #10 deliver_event (qe=<optimized out>, qevent=<optimized out>) at builtin-top.c:1202
  #11 0x00005555558a9318 in do_flush (show_progress=false, oe=0x7fffffff80e0) at util/ordered-events.c:244
  #12 __ordered_events__flush (oe=oe@entry=0x7fffffff80e0, how=how@entry=OE_FLUSH__TOP, timestamp=timestamp@entry=0) at util/ordered-events.c:323
  #13 0x00005555558a9789 in __ordered_events__flush (timestamp=<optimized out>, how=<optimized out>, oe=<optimized out>) at util/ordered-events.c:339
  #14 ordered_events__flush (how=OE_FLUSH__TOP, oe=0x7fffffff80e0) at util/ordered-events.c:341
  #15 ordered_events__flush (oe=oe@entry=0x7fffffff80e0, how=how@entry=OE_FLUSH__TOP) at util/ordered-events.c:339
  #16 0x00005555557cd631 in process_thread (arg=0x7fffffff7db0) at builtin-top.c:1114
  #17 0x00007ffff7bb817a in start_thread () from /lib64/libpthread.so.0
  #18 0x00007ffff5656dc3 in clone () from /lib64/libc.so.6

If you look at the frame #2, the code is:

488  if (he->srcline) {
489          he->srcline = strdup(he->srcline);
490          if (he->srcline == NULL)
491              goto err_rawdata;
492  }

If he->srcline is not NULL (it is not NULL if it is uninitialized rubbish),
it gets strdupped and strdupping a rubbish random string causes the problem.

Also, if you look at the commit 1fb7d06a509e, it adds the srcline property
into the struct, but not initializing it everywhere needed.

Committer notes:

Now I see, when using --ignore-callees=do_idle we end up here at line
2189 in add_callchain_ip():

2181         if (al.sym != NULL) {
2182                 if (perf_hpp_list.parent && !*parent &&
2183                     symbol__match_regex(al.sym, &parent_regex))
2184                         *parent = al.sym;
2185                 else if (have_ignore_callees && root_al &&
2186                   symbol__match_regex(al.sym, &ignore_callees_regex)) {
2187                         /* Treat this symbol as the root,
2188                            forgetting its callees. */
2189                         *root_al = al;
2190                         callchain_cursor_reset(cursor);
2191                 }
2192         }

And the al that doesn't have the ->srcline field initialized will be
copied to the root_al, so then, back to:

1211 int hist_entry_iter__add(struct hist_entry_iter *iter, struct addr_location *al,
1212                          int max_stack_depth, void *arg)
1213 {
1214         int err, err2;
1215         struct map *alm = NULL;
1216
1217         if (al)
1218                 alm = map__get(al->map);
1219
1220         err = sample__resolve_callchain(iter->sample, &callchain_cursor, &iter->parent,
1221                                         iter->evsel, al, max_stack_depth);
1222         if (err) {
1223                 map__put(alm);
1224                 return err;
1225         }
1226
1227         err = iter->ops->prepare_entry(iter, al);
1228         if (err)
1229                 goto out;
1230
1231         err = iter->ops->add_single_entry(iter, al);
1232         if (err)
1233                 goto out;
1234

That al at line 1221 is what hist_entry_iter__add() (called from
sample__resolve_callchain()) saw as 'root_al', and then:

        iter->ops->add_single_entry(iter, al);

will go on with al->srcline with a bogus value, I'll add the above
sequence to the cset and apply, thanks!

Signed-off-by: Michael Petlan <mpetlan@redhat.com>
CC: Milian Wolff <milian.wolff@kdab.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Fixes: 1fb7d06a509e ("perf report Use srcline from callchain for hist entries")
Link: https //lore.kernel.org/r/20210719145332.29747-1-mpetlan@redhat.com
Reported-by: Juri Lelli <jlelli@redhat.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/rockchip: cdn-dp-core: Make cdn_dp_core_resume __maybe_unused

commit 040b8907ccf1c78d020aca29800036565d761d73 upstream.

With the new static annotation, the compiler warns when the functions
are actually unused:

   drivers/gpu/drm/rockchip/cdn-dp-core.c:1123:12: error: 'cdn_dp_resume' defined but not used [-Werror=unused-function]
    1123 | static int cdn_dp_resume(struct device *dev)
         |            ^~~~~~~~~~~~~

Mark them __maybe_unused to suppress that warning as well.

[ Not so 'new' static annotations any more, and I removed the part of
  the patch that added __maybe_unused to cdn_dp_suspend(), because it's
  used by the shutdown/remove code.

  So only the resume function ends up possibly unused if CONFIG_PM isn't
  set     - Linus ]

Fixes: 7c49abb4c2f8 ("drm/rockchip: cdn-dp-core: Make cdn_dp_core_suspend/resume static")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tipc: increase timeout in tipc_sk_enqueue()

commit f4bb62e64c88c93060c051195d3bbba804e56945 upstream.

In tipc_sk_enqueue() we use hardcoded 2 jiffies to extract
socket buffer from generic queue to particular socket.
The 2 jiffies is too short in case there are other high priority
tasks get CPU cycles for multiple jiffies update. As result, no
buffer could be enqueued to particular socket.

To solve this, we switch to use constant timeout 20msecs.
Then, the function will be expired between 2 jiffies (CONFIG_100HZ)
and 20 jiffies (CONFIG_1000HZ).

Fixes: c637c1035534 ("tipc: resolve race problem at unicast message reception")
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: Hoang Le <hoang.h.le@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

r6040: Restore MDIO clock frequency after MAC reset

commit e3f0cc1a945fcefec0c7c9d9dfd028a51daa1846 upstream.

A number of users have reported that they were not able to get the PHY
to successfully link up, especially after commit c36757eb9dee ("net:
phy: consider AN_RESTART status when reading link status") where we
stopped reading just BMSR, but we also read BMCR to determine the link
status.

Andrius at NetBSD did a wonderful job at debugging the problem
and found out that the MDIO bus clock frequency would be incorrectly set
back to its default value which would prevent the MDIO bus controller
from reading PHY registers properly. Back when we only read BMSR, if we
read all 1s, we could falsely indicate a link status, though in general
there is a cable plugged in, so this went unnoticed. After a second read
of BMCR was added, a wrong read will lead to the inability to determine
a link UP condition which is when it started to be visibly broken, even
if it was long before that.

The fix consists in restoring the value of the MD_CSR register that was
set prior to the MAC reset.

Link: http://gnats.netbsd.org/cgi-bin/query-pr-single.pl?number=53494
Fixes: 90f750a81a29 ("r6040: consolidate MAC reset to its own function")
Reported-by: Andrius V <vezhlys@gmail.com>
Reported-by: Darek Strugacz <darek.strugacz@op.pl>
Tested-by: Darek Strugacz <darek.strugacz@op.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net/l2tp: Fix reference count leak in l2tp_udp_recv_core

commit 9b6ff7eb666415e1558f1ba8a742f5db6a9954de upstream.

The reference count leak issue may take place in an error handling
path. If both conditions of tunnel->version == L2TP_HDR_VER_3 and the
return value of l2tp_v3_ensure_opt_in_linear is nonzero, the function
would directly jump to label invalid, without decrementing the reference
count of the l2tp_session object session increased earlier by
l2tp_tunnel_get_session(). This may result in refcount leaks.

Fix this issue by decrease the reference count before jumping to the
label invalid.

Fixes: 4522a70db7aa ("l2tp: fix reading optional fields of L2TPv3")
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Xin Xiong <xiongx18@fudan.edu.cn>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dccp: don't duplicate ccid when cloning dccp sock

commit d9ea761fdd197351890418acd462c51f241014a7 upstream.

Commit 2677d2067731 ("dccp: don't free ccid2_hc_tx_sock ...") fixed
a UAF but reintroduced CVE-2017-6074.

When the sock is cloned, two dccps_hc_tx_ccid will reference to the
same ccid. So one can free the ccid object twice from two socks after
cloning.

This issue was found by "Hadar Manor" as well and assigned with
CVE-2020-16119, which was fixed in Ubuntu's kernel. So here I port
the patch from Ubuntu to fix it.

The patch prevents cloned socks from referencing the same ccid.

Fixes: 2677d2067731410 ("dccp: don't free ccid2_hc_tx_sock ...")
Signed-off-by: Zhenpeng Lin <zplin@psu.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ptp: dp83640: don't define PAGE0

commit 7366c23ff492ad260776a3ee1aaabba9fc773a8b upstream.

Building dp83640.c on arch/parisc/ produces a build warning for
PAGE0 being redefined. Since the macro is not used in the dp83640
driver, just make it a comment for documentation purposes.

In file included from ../drivers/net/phy/dp83640.c:23:
../drivers/net/phy/dp83640_reg.h:8: warning: "PAGE0" redefined
    8 | #define PAGE0                     0x0000
                 from ../drivers/net/phy/dp83640.c:11:
../arch/parisc/include/asm/page.h:187: note: this is the location of the previous definition
  187 | #define PAGE0   ((struct zeropage *)__PAGE_OFFSET)

Fixes: cb646e2b02b2 ("ptp: Added a clock driver for the National Semiconductor PHYTER.")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Richard Cochran <richard.cochran@omicron.at>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Russell King <linux@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20210913220605.19682-1-rdunlap@infradead.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net-caif: avoid user-triggerable WARN_ON(1)

commit 550ac9c1aaaaf51fd42e20d461f0b1cdbd55b3d2 upstream.

syszbot triggers this warning, which looks something
we can easily prevent.

If we initialize priv->list_field in chnl_net_init(),
then always use list_del_init(), we can remove robust_list_del()
completely.

WARNING: CPU: 0 PID: 3233 at net/caif/chnl_net.c:67 robust_list_del net/caif/chnl_net.c:67 [inline]
WARNING: CPU: 0 PID: 3233 at net/caif/chnl_net.c:67 chnl_net_uninit+0xc9/0x2e0 net/caif/chnl_net.c:375
Modules linked in:
CPU: 0 PID: 3233 Comm: syz-executor.3 Not tainted 5.14.0-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
RIP: 0010:robust_list_del net/caif/chnl_net.c:67 [inline]
RIP: 0010:chnl_net_uninit+0xc9/0x2e0 net/caif/chnl_net.c:375
Code: 89 eb e8 3a a3 ba f8 48 89 d8 48 c1 e8 03 42 80 3c 28 00 0f 85 bf 01 00 00 48 81 fb 00 14 4e 8d 48 8b 2b 75 d0 e8 17 a3 ba f8 <0f> 0b 5b 5d 41 5c 41 5d e9 0a a3 ba f8 4c 89 e3 e8 02 a3 ba f8 4c
RSP: 0018:ffffc90009067248 EFLAGS: 00010202
RAX: 0000000000008780 RBX: ffffffff8d4e1400 RCX: ffffc9000fd34000
RDX: 0000000000040000 RSI: ffffffff88bb6e49 RDI: 0000000000000003
RBP: ffff88802cd9ee08 R08: 0000000000000000 R09: ffffffff8d0e6647
R10: ffffffff88bb6dc2 R11: 0000000000000000 R12: ffff88803791ae08
R13: dffffc0000000000 R14: 00000000e600ffce R15: ffff888073ed3480
FS:  00007fed10fa0700(0000) GS:ffff8880b9d00000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000001b2c322000 CR3: 00000000164a6000 CR4: 00000000001506e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
 register_netdevice+0xadf/0x1500 net/core/dev.c:10347
 ipcaif_newlink+0x4c/0x260 net/caif/chnl_net.c:468
 __rtnl_newlink+0x106d/0x1750 net/core/rtnetlink.c:3458
 rtnl_newlink+0x64/0xa0 net/core/rtnetlink.c:3506
 rtnetlink_rcv_msg+0x413/0xb80 net/core/rtnetlink.c:5572
 netlink_rcv_skb+0x153/0x420 net/netlink/af_netlink.c:2504
 netlink_unicast_kernel net/netlink/af_netlink.c:1314 [inline]
 netlink_unicast+0x533/0x7d0 net/netlink/af_netlink.c:1340
 netlink_sendmsg+0x86d/0xdb0 net/netlink/af_netlink.c:1929
 sock_sendmsg_nosec net/socket.c:704 [inline]
 sock_sendmsg+0xcf/0x120 net/socket.c:724
 __sys_sendto+0x21c/0x320 net/socket.c:2036
 __do_sys_sendto net/socket.c:2048 [inline]
 __se_sys_sendto net/socket.c:2044 [inline]
 __x64_sys_sendto+0xdd/0x1b0 net/socket.c:2044
 do_syscall_x64 arch/x86/entry/common.c:50 [inline]
 do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
 entry_SYSCALL_64_after_hwframe+0x44/0xae

Fixes: cc36a070b590 ("net-caif: add CAIF netdevice")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net/{mlx5|nfp|bnxt}: Remove unnecessary RTNL lock assert

commit 7c3a0a018e672a9723a79b128227272562300055 upstream.

Remove the assert from the callback priv lookup function since it does
not require RTNL lock and is already protected by flow_indr_block_lock.

This will avoid warnings from being emitted to dmesg if the driver
registers its callback after an ingress qdisc was created for a
netdevice.

The warnings started after the following patch was merged:
commit 74fc4f828769 ("net: Fix offloading indirect devices dependency on qdisc order creation")

Signed-off-by: Eli Cohen <elic@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ethtool: Fix rxnfc copy to user buffer overflow

commit 9b29a161ef38040f000dcf9ccf78e34495edfd55 upstream.

In the cited commit, copy_to_user() got called with the wrong pointer,
instead of passing the actual buffer ptr to copy from, a pointer to
the pointer got passed, which causes a buffer overflow calltrace to pop
up when executing "ethtool -x ethX".

Fix ethtool_rxnfc_copy_to_user() to use the rxnfc pointer as passed
to the function, instead of a pointer to it.

This fixes below call trace:
[   15.533533] ------------[ cut here ]------------
[   15.539007] Buffer overflow detected (8 < 192)!
[   15.544110] WARNING: CPU: 3 PID: 1801 at include/linux/thread_info.h:200 copy_overflow+0x15/0x20
[   15.549308] Modules linked in:
[   15.551449] CPU: 3 PID: 1801 Comm: ethtool Not tainted 5.14.0-rc2+ #1058
[   15.553919] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
[   15.558378] RIP: 0010:copy_overflow+0x15/0x20
[   15.560648] Code: e9 7c ff ff ff b8 a1 ff ff ff eb c4 66 0f 1f 84 00 00 00 00 00 55 48 89 f2 89 fe 48 c7 c7 88 55 78 8a 48 89 e5 e8 06 5c 1e 00 <0f> 0b 5d c3 0f 1f 80 00 00 00 00 0f 1f 44 00 00 55 48 89 e5 41 55
[   15.565114] RSP: 0018:ffffad49c0523bd0 EFLAGS: 00010286
[   15.566231] RAX: 0000000000000000 RBX: 00000000000000c0 RCX: 0000000000000000
[   15.567616] RDX: 0000000000000001 RSI: ffffffff8a7912e7 RDI: 00000000ffffffff
[   15.569050] RBP: ffffad49c0523bd0 R08: ffffffff8ab2ae28 R09: 00000000ffffdfff
[   15.570534] R10: ffffffff8aa4ae40 R11: ffffffff8aa4ae40 R12: 0000000000000000
[   15.571899] R13: 00007ffd4cc2a230 R14: ffffad49c0523c00 R15: 0000000000000000
[   15.573584] FS:  00007f538112f740(0000) GS:ffff96d5bdd80000(0000) knlGS:0000000000000000
[   15.575639] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[   15.577092] CR2: 00007f5381226d40 CR3: 0000000013542000 CR4: 00000000001506e0
[   15.578929] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[   15.580695] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[   15.582441] Call Trace:
[   15.582970]  ethtool_rxnfc_copy_to_user+0x30/0x46
[   15.583815]  ethtool_get_rxnfc.cold+0x23/0x2b
[   15.584584]  dev_ethtool+0x29c/0x25f0
[   15.585286]  ? security_netlbl_sid_to_secattr+0x77/0xd0
[   15.586728]  ? do_set_pte+0xc4/0x110
[   15.587349]  ? _raw_spin_unlock+0x18/0x30
[   15.588118]  ? __might_sleep+0x49/0x80
[   15.588956]  dev_ioctl+0x2c1/0x490
[   15.589616]  sock_ioctl+0x18e/0x330
[   15.591143]  __x64_sys_ioctl+0x41c/0x990
[   15.591823]  ? irqentry_exit_to_user_mode+0x9/0x20
[   15.592657]  ? irqentry_exit+0x33/0x40
[   15.593308]  ? exc_page_fault+0x32f/0x770
[   15.593877]  ? exit_to_user_mode_prepare+0x3c/0x130
[   15.594775]  do_syscall_64+0x35/0x80
[   15.595397]  entry_SYSCALL_64_after_hwframe+0x44/0xae
[   15.596037] RIP: 0033:0x7f5381226d4b
[   15.596492] Code: 0f 1e fa 48 8b 05 3d b1 0c 00 64 c7 00 26 00 00 00 48 c7 c0 ff ff ff ff c3 66 0f 1f 44 00 00 f3 0f 1e fa b8 10 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d 0d b1 0c 00 f7 d8 64 89 01 48
[   15.598743] RSP: 002b:00007ffd4cc2a1f8 EFLAGS: 00000246 ORIG_RAX: 0000000000000010
[   15.599804] RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007f5381226d4b
[   15.600795] RDX: 00007ffd4cc2a350 RSI: 0000000000008946 RDI: 0000000000000003
[   15.601712] RBP: 00007ffd4cc2a340 R08: 00007ffd4cc2a350 R09: 0000000000000001
[   15.602751] R10: 00007f538128a990 R11: 0000000000000246 R12: 0000000000000000
[   15.603882] R13: 00007ffd4cc2a350 R14: 00007ffd4cc2a4b0 R15: 0000000000000000
[   15.605042] ---[ end trace 325cf185e2795048 ]---

Fixes: dd98d2895de6 ("ethtool: improve compat ioctl handling")
Reported-by: Shannon Nelson <snelson@pensando.io>
CC: Arnd Bergmann <arnd@arndb.de>
CC: Christoph Hellwig <hch@lst.de>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Tested-by: Shannon Nelson <snelson@pensando.io>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tipc: fix an use-after-free issue in tipc_recvmsg

commit cc19862ffe454a5b632ca202e5a51bfec9f89fd2 upstream.

syzbot reported an use-after-free crash:

  BUG: KASAN: use-after-free in tipc_recvmsg+0xf77/0xf90 net/tipc/socket.c:1979
  Call Trace:
   tipc_recvmsg+0xf77/0xf90 net/tipc/socket.c:1979
   sock_recvmsg_nosec net/socket.c:943 [inline]
   sock_recvmsg net/socket.c:961 [inline]
   sock_recvmsg+0xca/0x110 net/socket.c:957
   tipc_conn_rcv_from_sock+0x162/0x2f0 net/tipc/topsrv.c:398
   tipc_conn_recv_work+0xeb/0x190 net/tipc/topsrv.c:421
   process_one_work+0x98d/0x1630 kernel/workqueue.c:2276
   worker_thread+0x658/0x11f0 kernel/workqueue.c:2422

As Hoang pointed out, it was caused by skb_cb->bytes_read still accessed
after calling tsk_advance_rx_queue() to free the skb in tipc_recvmsg().

This patch is to fix it by accessing skb_cb->bytes_read earlier than
calling tsk_advance_rx_queue().

Fixes: f4919ff59c28 ("tipc: keep the skb in rcv queue until the whole data is read")
Reported-by: syzbot+e6741b97d5552f97c24d@syzkaller.appspotmail.com
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>