drm/selftests: missing error code in igt_buddy_alloc_smoke()

Set the error code to -ENOMEM if drm_random_order() fails.

Fixes: e6ff5ef81170 ("drm/selftests: add drm buddy smoke testcase")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Arunpravin <Arunpravin.PaneerSelvam@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220307125458.GA16710@kili

drm: Drop commas after SoC match table sentinels

It does not make sense to have a comma after a sentinel, as any new
elements must be added before the sentinel.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/298f0644275d7d0b4aa3ee7143756a2431a4900c.1646311443.git.geert+renesas@glider.be

efifb: Remove redundant efifb_setup_from_dmi stub

efifb is the only user of efifb_setup_from_dmi which is provided by
sysfb which is selected by efifb. That makes the stub redundant.

Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/7416c439d68e9e96068ea5c77e05c99c7df41750.1645822213.git.msuchanek@suse.de

sysfb: Enable boot time VESA graphic mode selection

Since switch to simplefb/simpledrm VESA graphic mode selection with vga=
kernel parameter is no longer available with legacy BIOS.

The x86 realmode boot code enables the VESA graphic modes when option
FB_BOOT_VESA_SUPPORT is enabled.

This option is selected by vesafb but not simplefb/simpledrm.

To enable use of VESA modes with simplefb in legacy BIOS boot mode drop
dependency of BOOT_VESA_SUPPORT on FB, also drop the FB_ prefix. Select
the option from sysfb rather than the drivers that depend on it.

The BOOT_VESA_SUPPORT is not specific to framebuffer but rather to x86
platform, move it from fbdev to x86 Kconfig.

Fixes: e3263ab389a7 ("x86: provide platform-devices for boot-framebuffers")
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/948c39940a4e99f5b43bdbcbe537faae71a43e1d.1645822213.git.msuchanek@suse.de

sysfb: Make config option dependencies explicit

efifb and vesafb requires sysfb implicitly but this is not stated in
Kconfig. Add the dependency.

With that all drivers that require sysfb depend on it so it can default
to disabled.

Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/a0fa41e9186653e4c41ad0a28259e5cdc71b1f66.1645822213.git.msuchanek@suse.de

drm/bridge_connector: enable HPD by default if supported

Hotplug events reported by bridge drivers over drm_bridge_hpd_notify()
get ignored unless somebody calls drm_bridge_hpd_enable(). When the
connector for the bridge is bridge_connector, such a call is done from
drm_bridge_connector_enable_hpd().

However drm_bridge_connector_enable_hpd() is never called on init paths,
documentation suggests that it is intended for suspend/resume paths.

In result, once encoders are switched to bridge_connector,
bridge-detected HPD stops working.

This patch adds a call to that API on init path.

This fixes HDMI HPD with rcar-du + adv7513 case when adv7513 reports HPD
events via interrupts.

Fixes: c24110a8fd09 ("drm: rcar-du: Use drm_bridge_connector_init() helper")
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211225063151.2110878-1-nikita.yoush@cogentembedded.com

drm/selftests: fix a shift-out-of-bounds bug

pass the correct size value computed using the max_order.

<log snip>

[ 68.124177][ T1] UBSAN: shift-out-of-bounds in include/linux/log2.h:67:13
[ 68.125333][ T1] shift exponent 4294967295 is too large for 32-bit type 'long
unsigned int'
[ 68.126563][ T1] CPU: 0 PID: 1 Comm: swapper Not tainted
5.17.0-rc2-00311-g39ec47bbfd5d #2
[ 68.127758][ T1] Call Trace:
[ 68.128187][ T1] dump_stack_lvl (lib/dump_stack.c:108)
[ 68.128793][ T1] dump_stack (lib/dump_stack.c:114)
[ 68.129331][ T1] ubsan_epilogue (lib/ubsan.c:152)
[ 68.129958][ T1] __ubsan_handle_shift_out_of_bounds.cold (arch/x86/include/asm/smap.h:85)

[ 68.130791][ T1] ? drm_block_alloc+0x28/0x80
[ 68.131582][ T1] ? rcu_read_lock_sched_held (kernel/rcu/update.c:125)
[ 68.132215][ T1] ? kmem_cache_alloc (include/trace/events/kmem.h:54 mm/slab.c:3501)
[ 68.132878][ T1] ? mark_free+0x2e/0x80
[ 68.133524][ T1] drm_buddy_init.cold (include/linux/log2.h:67
drivers/gpu/drm/drm_buddy.c:131)
[ 68.134145][ T1] ? test_drm_cmdline_init (drivers/gpu/drm/selftests/test-drm_buddy.c:87)

[ 68.134770][ T1] igt_buddy_alloc_limit (drivers/gpu/drm/selftests/test-drm_buddy.c:30)
[ 68.135472][ T1] ? vprintk_default (kernel/printk/printk.c:2257)
[ 68.136057][ T1] ? test_drm_cmdline_init (drivers/gpu/drm/selftests/test-drm_buddy.c:87)

[ 68.136812][ T1] test_drm_buddy_init (drivers/gpu/drm/selftests/drm_selftest.c:77
drivers/gpu/drm/selftests/test-drm_buddy.c:95)
[ 68.137475][ T1] do_one_initcall (init/main.c:1300)
[ 68.138111][ T1] ? parse_args (kernel/params.c:609 kernel/params.c:146
kernel/params.c:188)
[ 68.138717][ T1] do_basic_setup (init/main.c:1372 init/main.c:1389 init/main.c:1408)
[ 68.139366][ T1] kernel_init_freeable (init/main.c:1617)
[ 68.140040][ T1] ? rest_init (init/main.c:1494)
[ 68.140634][ T1] kernel_init (init/main.c:1504)
[ 68.141155][ T1] ret_from_fork (arch/x86/entry/entry_32.S:772)
[ 68.141607][ T1]
================================================================================
[ 68.146730][ T1] ------------[ cut here ]------------
[ 68.147460][ T1] kernel BUG at drivers/gpu/drm/drm_buddy.c:140!
[ 68.148280][ T1] invalid opcode: 0000 [#1]
[ 68.148895][ T1] CPU: 0 PID: 1 Comm: swapper Not tainted
5.17.0-rc2-00311-g39ec47bbfd5d #2
[ 68.149896][ T1] EIP: drm_buddy_init (drivers/gpu/drm/drm_buddy.c:140 (discriminator 1))

For more details: https://lists.01.org/hyperkitty/list/lkp@lists.01.org/thread/FDIF3HCILZNN5UQAZMOR7E3MQSMHHKWU/

Signed-off-by: Arunpravin <Arunpravin.PaneerSelvam@amd.com>
Reported-by: kernel test robot <oliver.sang@intel.com>
Acked-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220303201602.2365-1-Arunpravin.PaneerSelvam@amd.com
Signed-off-by: Christian König <christian.koenig@amd.com>

drm/nouveau/instmem: fix uninitialized_var.cocci warning

Fix following coccicheck warning:
drivers/gpu/drm/nouveau/nvkm/subdev/instmem/nv50.c:316:11-12:
WARNING this kind of initialization is deprecated.

`void *map = map` has the same form of
uninitialized_var() macro. I remove the redundant assignement. It has
been tested with gcc (Debian 8.3.0-6) 8.3.0.

The patch which removed uninitialized_var() is:
https://lore.kernel.org/all/20121028102007.GA7547@gmail.com/
And there is very few "/* GCC */" comments in the Linux kernel code now.

Signed-off-by: Guo Zhengkui <guozhengkui@vivo.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220228142352.18006-1-guozhengkui@vivo.com

drm/ssd130x: remove redundant initialization of pointer mode

Pointer mode is being assigned a value that is never read, it is
being re-assigned later with a new value. The initialization is
redundant and can be removed.

Cleans up clang scan build warning:
drivers/gpu/drm/solomon/ssd130x.c:582:27: warning: Value stored
to 'mode' during its initialization is never read [deadcode.DeadStores]

Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Acked-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220302175309.1098827-1-colin.i.king@gmail.com

drm/aspeed: Add AST2600 chip support

Add AST2600 chip support and setting.

Signed-off-by: Tommy Haung <tommy_huang@aspeedtech.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Link: https://patchwork.freedesktop.org/patch/msgid/20220302024930.18758-5-tommy_huang@aspeedtech.com

drm/aspeed: Update INTR_STS handling

Add interrupt clear register define for further chip support.

Signed-off-by: Tommy Haung <tommy_huang@aspeedtech.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Link: https://patchwork.freedesktop.org/patch/msgid/20220302024930.18758-4-tommy_huang@aspeedtech.com

drm: Add TODO item for optimizing format helpers

Add a TODO item for optimizing blitting and format-conversion helpers
in DRM and fbdev. There's always demand for faster graphics output.

v4:
* fix typos (Sam)

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220223193804.18636-6-tzimmermann@suse.de

fbdev: Improve performance of cfb_imageblit()

Improve the performance of cfb_imageblit() by manually unrolling
the inner blitting loop and moving some invariants out. The compiler
failed to do this automatically. This change keeps cfb_imageblit()
in sync with sys_imagebit().

A microbenchmark measures the average number of CPU cycles
for cfb_imageblit() after a stabilizing period of a few minutes
(i7-4790, FullHD, simpledrm, kernel with debugging).

cfb_imageblit(), new: 15724 cycles
cfb_imageblit(): old: 30566 cycles

In the optimized case, cfb_imageblit() is now ~2x faster than before.

v3:
* fix commit description (Pekka)

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220223193804.18636-5-tzimmermann@suse.de

fbdev: Remove trailing whitespaces from cfbimgblt.c

Fix coding style. No functional changes.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220223193804.18636-4-tzimmermann@suse.de

fbdev: Improve performance of sys_imageblit()

Improve the performance of sys_imageblit() by manually unrolling
the inner blitting loop and moving some invariants out. The compiler
failed to do this automatically. The resulting binary code was even
slower than the cfb_imageblit() helper, which uses the same algorithm,
but operates on I/O memory.

A microbenchmark measures the average number of CPU cycles
for sys_imageblit() after a stabilizing period of a few minutes
(i7-4790, FullHD, simpledrm, kernel with debugging). The value
for CFB is given as a reference.

  sys_imageblit(), new: 25934 cycles
  sys_imageblit(), old: 35944 cycles
  cfb_imageblit():      30566 cycles

In the optimized case, sys_imageblit() is now ~30% faster than before
and ~20% faster than cfb_imageblit().

v2:
* move switch out of inner loop (Gerd)
* remove test for alignment of dst1 (Sam)

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220223193804.18636-3-tzimmermann@suse.de

fbdev: Improve performance of sys_fillrect()

Improve the performance of sys_fillrect() by using word-aligned
32/64-bit mov instructions. While the code tried to implement this,
the compiler failed to create fast instructions. The resulting
binary instructions were even slower than cfb_fillrect(), which
uses the same algorithm, but operates on I/O memory.

A microbenchmark measures the average number of CPU cycles
for sys_fillrect() after a stabilizing period of a few minutes
(i7-4790, FullHD, simpledrm, kernel with debugging). The value
for CFB is given as a reference.

  sys_fillrect(), new:  26586 cycles
  sys_fillrect(), old: 166603 cycles
  cfb_fillrect():       41012 cycles

In the optimized case, sys_fillrect() is now ~6x faster than before
and ~1.5x faster than the CFB implementation.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220223193804.18636-2-tzimmermann@suse.de

drm/panfrost: cleanup comments

For spdx
change tab to space delimiter
Use // for *.c

Replacements
commited to committed
regsiters to registers
initialze to initialize

Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Steven Price <steven.price@arm.com>
Signed-off-by: Steven Price <steven.price@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220302124535.358060-1-trix@redhat.com

drm/bridge: nwl-dsi: Remove superfluous write to NWL_DSI_IRQ_MASK register

To initialize register NWL_DSI_IRQ_MASK, it's enough to write it
only once in function nwl_dsi_init_interrupts().

Signed-off-by: Liu Ying <victor.liu@nxp.com>
Reviewed-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220216085842.1973868-1-victor.liu@nxp.com

drm/bridge: Clear the DP_AUX_I2C_MOT bit passed in aux read command.

If the previous transfer didn't end with a command without DP_AUX_I2C_MOT,
the next read trasnfer will miss the first byte. But if the command in
previous transfer is requested with length 0, it's a no-op to anx7625
since it can't process this command. anx7625 requires the last command
to be read command with length > 0.

It's observed that if we clear the DP_AUX_I2C_MOT in read transfer, we
can still get correct data. Clear the read commands with DP_AUX_I2C_MOT
bit to fix this issue.

Fixes: adca62ec370c ("drm/bridge: anx7625: Support reading edid through aux channel")
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: Xin Ji <xji@analogixsemi.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220217082224.1823916-1-hsinyi@chromium.org

drm/v3d: centralize error handling when init scheduler fails

Remove redundant error message (since now it is very similar to what
we do in drm_sched_init) and centralize all error handling in a
unique place, as we follow the same steps in any case of failure.

Signed-off-by: Melissa Wen <mwen@igalia.com>
Acked-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Signed-off-by: Melissa Wen <melissa.srw@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220228181647.3794298-1-mwen@igalia.com

drm/bridge: chipone-icn6211: switch to devm_drm_of_get_bridge

The function "drm_of_find_panel_or_bridge" has been deprecated in
favor of "devm_drm_of_get_bridge".

Switch to the new function and reduce boilerplate.

Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Reviewed-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220221074224.12920-1-jose.exposito89@gmail.com

drm/bridge: anx7625: Fix release wrong workqueue

If "hdcp_workqueue" exist, must release "hdcp_workqueue",
not "workqueue".

Fixes: cd1637c7e480 ("drm/bridge: anx7625: add HDCP support")
Signed-off-by: Xin Ji <xji@analogixsemi.com>
Reviewed-by: Hsin-Yi Wang <hsinyi@chromium.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220217024418.3780171-1-xji@analogixsemi.com

drm/bridge: it6505: Fix the read buffer array bound

The size of read_buf is READ_BUFFER_SIZE (200), so we can't access it
with read_buf + PAGE_SIZE (4096). Extend the READ_BUFFER_SIZE to 400 and
set the end position to read_buf + READ_BUFFER_SIZE.

Fixes: b5c84a9edcd418 ("drm/bridge: add it6505 driver")
Reported-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220228081421.1504213-1-hsinyi@chromium.org

drm/panel: simple: Initialize bpc in RK101II01D-CT panel descriptor

Initialize bpc while creating panel_desc structure for RK101II01D-CT

Below warning is triggered since bpc is not being initialized

WARNING: CPU: 2 PID: 47 at drivers/gpu/drm/panel/panel-simple.c:614
panel_simple_probe+0x1b0/0x3c8

Signed-off-by: Rahul T R <r-ravikumar@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220210140300.11900-1-r-ravikumar@ti.com

drm/bridge: cdns-dsi: Make sure to to create proper aliases for dt

Add MODULE_DEVICE_TABLE to the device tree table to create required
aliases needed for module to be loaded with device tree based platform.

Fixes: e19233955d9e ("drm/bridge: Add Cadence DSI driver")
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210921174059.17946-1-nm@ti.com

drm/tiny: Add MIPI DBI compatible SPI driver

Add a driver that will work with most MIPI DBI compatible SPI panels.
This avoids adding a driver for every new MIPI DBI compatible controller
that is to be used by Linux. The 'compatible' Device Tree property with
a '.bin' suffix will be used to load a firmware file that contains the
controller configuration.

Example (driver will load sainsmart18.bin):

display@0 {
compatible = "sainsmart18", "panel-mipi-dbi-spi";
...
};

v5:
- kconfig: s/DRM_KMS_CMA_HELPER/DRM_GEM_CMA_HELPER/ (Sam)
- kconfig: Add select VIDEOMODE_HELPERS (Sam)
- kconfig: Add wiki url in the description (Sam)
- Split out and use of_get_drm_panel_display_mode()(Sam)
- Only use the first compatible to look for a firmware file since the
  binding mandates 2 compatibles.
- Make having a firmware file mandatory so we can print an error
  message if it's missing to improve the user experience. It's very
  unlikely that a controller doesn't need to be initialized and if
  it doesn't, it's possible to have a firmware file containing only
  a DCS NOP.

v4:
- Move driver to drm/tiny where the other drivers of its kind are located.
  The driver module will not be shared with a future DPI driver after all.

v3:
- Move properties to DT (Maxime)
- The MIPI DPI spec has optional support for DPI where the controller is
  configured over DBI. Rework the command functions so they can be moved
  to drm_mipi_dbi and shared with a future panel-mipi-dpi-spi driver

v2:
- Drop model property and use compatible instead (Rob)
- Add wiki entry in MAINTAINERS

Acked-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220227124713.39766-6-noralf@tronnes.org

drm/mipi-dbi: Add driver_private member to struct mipi_dbi_dev

devm_drm_dev_alloc() can't allocate structures that embed a structure
which then again embeds drm_device. Workaround this by adding a
driver_private pointer to struct mipi_dbi_dev which the driver can use for
its additional state.

v3:
- Add documentation

Acked-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220227124713.39766-5-noralf@tronnes.org

drm/modes: Add of_get_drm_panel_display_mode()

Add a function to get a drm_display_mode from a panel-timing
device tree subnode.

Suggested-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220227124713.39766-4-noralf@tronnes.org

drm/modes: Remove trailing whitespace

Remove trailing whitespace from a comment.

Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220227124713.39766-3-noralf@tronnes.org

dt-bindings: display: add bindings for MIPI DBI compatible SPI panels

Add binding for MIPI DBI compatible SPI panels.

v6:
- Fix indentation (Rob)

v5:
- Add sainsmart18 to compatible items (Rob)
- Expand write-only description (Sam)

v4:
- There should only be two compatible (Maxime)
- s/panel-dbi-spi/panel-mipi-dbi-spi/in compatible

v3:
- Move properties to Device Tree (Maxime)
- Use contains for compatible (Maxime)
- Add backlight property to example
- Flesh out description

v2:
- Fix path for panel-common.yaml
- Use unevaluatedProperties
- Drop properties which are in the allOf section
- Drop model property (Rob)

Acked-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220227124713.39766-2-noralf@tronnes.org

drm/todo: Update panic handling todo

Some things changed, and add two useful links.

v2: Also include a link to the QR encoding work. Plus review from
Javier.

v3: Fix typo Guilherme spotted.

Reviewed-by: Guilherme G. Piccoli <gpiccoli@igalia.com>
Acked-by: Pekka Paalanen <pekka.paalanen@collabora.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Cc: Javier Martinez Canillas <javierm@redhat.com>
Cc: Pekka Paalanen <ppaalanen@gmail.com>
Cc: gpiccoli@igalia.com
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220224132425.3463791-1-daniel.vetter@ffwll.ch

drm/omap: plane: Remove redundant color encoding and range initialisation

The omap KMS driver will call drm_plane_create_color_properties() with
a default encoding and range values of BT601 and Full Range,
respectively.

Since the initial value wasn't carried over in the state, the driver had
to set it again in omap_plane_reset(). However, the helpers have been
adjusted to set it properly at reset, so this is not needed anymore.

Reviewed-by: Tomi Valkeinen <tomba@kernel.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220221095918.18763-23-maxime@cerno.tech

drm/object: Add default color encoding and range value at reset

The drm_plane_create_color_properties() function asks for an initial
value for the color encoding and range, and will set the associated
plane state variable with that value if a state is present.

However, that function is usually called at a time where there's no
state yet. Since the drm_plane_state reset helper doesn't take care of
reading that value when it's called, it means that in most cases the
initial value will be 0 (so DRM_COLOR_YCBCR_BT601 and
DRM_COLOR_YCBCR_LIMITED_RANGE, respectively), or the drivers will have
to work around it.

Let's add some code in __drm_atomic_helper_plane_state_reset() to get
the initial encoding and range value if the property has been attached
in order to fix this.

Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220221095918.18763-19-maxime@cerno.tech

drm/sun4i: layer: Remove redundant zpos initialisation

The sun4i KMS driver will call drm_plane_create_zpos_property() with an
init value depending on the plane type.

Since the initial value wasn't carried over in the state, the driver had
to set it again in sun4i_backend_layer_reset().
However, the helpers have been adjusted to set it properly at reset, so
this is not needed anymore.

Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-sunxi@lists.linux.dev
Cc: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220221095918.18763-18-maxime@cerno.tech

drm/sti: plane: Remove redundant zpos initialisation

The sti KMS driver will call drm_plane_create_zpos_property() with an
init value depending on the plane type.

Since the initial value wasn't carried over in the state, the driver had
to set it again in sti_plane_reset().
However, the helpers have been adjusted to set it properly at reset, so
this is not needed anymore.

Reviewed-by: Alain Volmat <alain.volmat@foss.st.com>
Reviewed-by: Philippe Cornu <philippe.cornu@foss.st.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220221095918.18763-17-maxime@cerno.tech

drm/rcar: plane: Remove redundant zpos initialisation

The rcar-du KMS driver will call drm_plane_create_zpos_property() with an
init value depending on the plane type.

Since the initial value wasn't carried over in the state, the driver had
to set it again in rcar_du_plane_reset() and rcar_du_vsp_plane_reset().
However, the helpers have been adjusted to set it properly at reset, so
this is not needed anymore.

Cc: linux-renesas-soc@vger.kernel.org
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220221095918.18763-16-maxime@cerno.tech

drm/omap: plane: Remove redundant zpos initialisation

The omap KMS driver will call drm_plane_create_zpos_property() with an
init value of the plane index and the plane type.

Since the initial value wasn't carried over in the state, the driver had
to set it again in omap_plane_reset(). However, the helpers have been
adjusted to set it properly at reset, so this is not needed anymore.

Reviewed-by: Tomi Valkeinen <tomba@kernel.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220221095918.18763-15-maxime@cerno.tech

drm/nouveau/kms: Remove redundant zpos initialisation

The nouveau KMS driver will call drm_plane_create_zpos_property() with
an init value depending on the plane purpose.

Since the initial value wasn't carried over in the state, the driver had
to set it again in nv50_wndw_reset(). However, the helpers have been
adjusted to set it properly at reset, so this is not needed anymore.

Cc: nouveau@lists.freedesktop.org
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Karol Herbst <kherbst@redhat.com>
Cc: Lyude Paul <lyude@redhat.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Karol Herbst <kherbst@redhat.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220221095918.18763-14-maxime@cerno.tech

drm/msm/mdp5: Remove redundant zpos initialisation

The mdp KMS driver will call drm_plane_create_zpos_property() with an
init value depending on the plane purpose.

Since the initial value wasn't carried over in the state, the driver had
to set it again in mdp5_plane_reset(). However, the helpers have been
adjusted to set it properly at reset, so this is not needed anymore.

Cc: freedreno@lists.freedesktop.org
Cc: linux-arm-msm@vger.kernel.org
Cc: Abhinav Kumar <quic_abhinavk@quicinc.com>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Sean Paul <sean@poorly.run>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220221095918.18763-13-maxime@cerno.tech

drm/object: Add default zpos value at reset

The drm_plane_create_zpos_property() function asks for an initial value,
and will set the associated plane state variable with that value if a
state is present.

However, that function is usually called at a time where there's no
state yet. Since the drm_plane_state reset helper doesn't take care of
reading that value when it's called, it means that in most cases the
initial value will be 0, or the drivers will have to work around it.

Let's add some code in __drm_atomic_helper_plane_state_reset() to get
the initial zpos value if the property has been attached in order to fix
this.

Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220221095918.18763-8-maxime@cerno.tech

drm/object: Add drm_object_property_get_default_value() function

Some functions to create properties (drm_plane_create_zpos_property or
drm_plane_create_color_properties for example) will ask for a range of
acceptable value and an initial one.

This initial value is then stored in the values array for that property.

Let's provide an helper to access this property.

Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220221095918.18763-7-maxime@cerno.tech

drm/omap: plane: Fix zpos initial value mismatch

While the omap_plane_init() function calls
drm_plane_create_zpos_property() with an initial value of 0,
omap_plane_reset() will force it to another value depending on the plane
type.

Fix the discrepancy by setting the initial zpos value to the same value
in the drm_plane_create_zpos_property() call.

Reviewed-by: Tomi Valkeinen <tomba@kernel.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220221095918.18763-5-maxime@cerno.tech

drm: of: Lookup if child node has panel or bridge

Devices can also be child nodes when we also control that device
through the upstream device (ie, MIPI-DCS for a MIPI-DSI device).

drm_of_find_panel_or_bridge can lookup panel or bridge for a given
device has port and endpoint and it fails to lookup if the device
has a child nodes.

This patch add support to lookup for a child node of the given parent
that isn't either port or ports.

Example OF graph representation of DSI host, which has port but
not has ports and has child panel node.

dsi {
compatible = "allwinner,sun6i-a31-mipi-dsi";
#address-cells = <1>;
#size-cells = <0>;

port {
dsi_in_tcon0: endpoint {
remote-endpoint = <tcon0_out_dsi>;
};

panel@0 {
reg = <0>;
};
};

Example OF graph representation of DSI host, which has ports but
not has port and has child panel node.

dsi {
        compatible = "samsung,exynos5433-mipi-dsi";
        #address-cells = <1>;
        #size-cells = <0>;

ports {
#address-cells = <1>;
#size-cells = <0>;

port@0 {
reg = <0>;

                 dsi_to_mic: endpoint {
                         remote-endpoint = <&mic_to_dsi>;
                 };
                };
        };

        panel@0 {
                reg = <0>;
        };
};

Example OF graph representation of DSI host, which has neither a port
nor a ports but has child panel node.

dsi0 {
compatible = "ste,mcde-dsi";
#address-cells = <1>;
#size-cells = <0>;

panel@0 {
reg = <0>;
};
};

Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220202160414.16493-1-jagan@amarulasolutions.com

drm/stm: ltdc: add support for CRC hashing feature

This patch adds the CRC hashing feature supported by some recent hardware
versions of the LTDC. This is useful for test suite such as IGT-GPU-tools
[1] where a CRTC output frame can be compared to a test reference frame
thanks to their respective CRC hash.

[1] https://cgit.freedesktop.org/drm/igt-gpu-tools

Signed-off-by: Raphael Gallais-Pou <raphael.gallais-pou@foss.st.com>
Acked-by: Yannick Fertre <yannick.fertre@foss.st.com>
Signed-off-by: Philippe Cornu <philippe.cornu@foss.st.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220211104620.421177-1-raphael.gallais-pou@foss.st.com

drm/stm: Avoid using val uninitialized in ltdc_set_ycbcr_config()

Clang warns:

  drivers/gpu/drm/stm/ltdc.c:625:2: warning: variable 'val' is used uninitialized whenever switch default is taken [-Wsometimes-uninitialized]
          default:
          ^~~~~~~
  drivers/gpu/drm/stm/ltdc.c:635:2: note: uninitialized use occurs here
          val |= LxPCR_YCEN;
          ^~~
  drivers/gpu/drm/stm/ltdc.c:600:9: note: initialize the variable 'val' to silence this warning
          u32 val;
                 ^
                  = 0
  1 warning generated.

Use a return instead of break in the default case to fix the warning.
Add an error message so that this return is not silent, which could hide
issues in the future.

Fixes: 484e72d3146b ("drm/stm: ltdc: add support of ycbcr pixel formats")
Link: https://github.com/ClangBuiltLinux/linux/issues/1575
Acked-by: Yannick Fertre <yannick.fertre@foss.st.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Raphael Gallais-Pou <raphael.gallais-pou@foss.st.com>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Philippe Cornu <philippe.cornu@foss.st.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220222152045.484610-1-nathan@kernel.org

drm/dp: Fix OOB read when handling Post Cursor2 register

The link_status array was not large enough to read the Adjust Request
Post Cursor2 register, so remove the common helper function to avoid
an OOB read, found with a -Warray-bounds build:

drivers/gpu/drm/drm_dp_helper.c: In function 'drm_dp_get_adjust_request_post_cursor':
drivers/gpu/drm/drm_dp_helper.c:59:27: error: array subscript 10 is outside array bounds of 'const u8[6]' {aka 'const unsigned char[6]'} [-Werror=array-bounds]
   59 |         return link_status[r - DP_LANE0_1_STATUS];
      |                ~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~
drivers/gpu/drm/drm_dp_helper.c:147:51: note: while referencing 'link_status'
  147 | u8 drm_dp_get_adjust_request_post_cursor(const u8 link_status[DP_LINK_STATUS_SIZE],
      |                                          ~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

Replace the only user of the helper with an open-coded fetch and decode,
similar to drivers/gpu/drm/amd/display/dc/core/dc_link_dp.c.

Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: David Airlie <airlied@linux.ie>
Cc: dri-devel@lists.freedesktop.org
Fixes: 79465e0ffeb9 ("drm/dp: Add helper to get post-cursor adjustments")
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://lore.kernel.org/r/20220105173507.2420910-1-keescook@chromium.org
Signed-off-by: Thierry Reding <treding@nvidia.com>

drm/dp: Fix off-by-one in register cache size

The pcon_dsc_dpcd array holds 13 registers (0x92 through 0x9E). Fix the
math to calculate the max size. Found from a -Warray-bounds build:

drivers/gpu/drm/drm_dp_helper.c: In function 'drm_dp_pcon_dsc_bpp_incr':
drivers/gpu/drm/drm_dp_helper.c:3130:28: error: array subscript 12 is outside array bounds of 'const u8[12]' {aka 'const unsigned char[12]'} [-Werror=array-bounds]
 3130 |         buf = pcon_dsc_dpcd[DP_PCON_DSC_BPP_INCR - DP_PCON_DSC_ENCODER];
      |               ~~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/gpu/drm/drm_dp_helper.c:3126:39: note: while referencing 'pcon_dsc_dpcd'
 3126 | int drm_dp_pcon_dsc_bpp_incr(const u8 pcon_dsc_dpcd[DP_PCON_DSC_ENCODER_CAP_SIZE])
      |                              ~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: David Airlie <airlied@linux.ie>
Cc: dri-devel@lists.freedesktop.org
Fixes: e2e16da398d9 ("drm/dp_helper: Add support for Configuring DSC for HDMI2.1 Pcon")
Cc: stable@vger.kernel.org
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/lkml/20211214001849.GA62559@embeddedor/
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20220105173310.2420598-1-keescook@chromium.org
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220225035610.2552144-2-keescook@chromium.org

drm/nouveau: Remove the unused header file nvif/list.h

The nouveau driver depends on include/linux/list.h instead of
nvif/list.h, so remove the obstacle-nvif/list.h.

Signed-off-by: Cai Huoqing <cai.huoqing@linux.dev>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220209065322.43938-1-cai.huoqing@linux.dev

drm/repaper: Use format helper for xrgb8888 to monochrome conversion

There is now a drm_fb_xrgb8888_to_mono_reversed() helper function to do
format conversion from XRGB8888 to reversed monochrome.

Use that helper and remove the open coded version in the repaper driver.

Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Tested-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Noralf Trønnes <noralf@tronnes.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220223193735.213185-1-javierm@redhat.com

drm/simpledrm: Add "panel orientation" property on non-upright mounted LCD panels

Some devices use e.g. a portrait panel in a standard laptop casing made
for landscape panels. efifb calls drm_get_panel_orientation_quirk() and
sets fb_info.fbcon_rotate_hint to make fbcon rotate the console so that
it shows up-right instead of on its side.

When switching to simpledrm the fbcon renders on its side. Call the
drm_connector_set_panel_orientation_with_quirk() helper to add
a "panel orientation" property on devices listed in the quirk table,
to make the fbcon (and aware userspace apps) rotate the image to
display properly.

Cc: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220221220045.11958-1-hdegoede@redhat.com

drm/selftests: add drm buddy pathological testcase

create a pot-sized mm, then allocate one of each possible
order within. This should leave the mm with exactly one
page left. Free the largest block, then whittle down again.
Eventually we will have a fully 50% fragmented mm.

v2(Matthew Auld):
  - removed unnecessary test succeeded print
  - replace list_del()/list_add_tail() with list_move_tail()

Signed-off-by: Arunpravin <Arunpravin.PaneerSelvam@amd.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Acked-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220222174845.2175-7-Arunpravin.PaneerSelvam@amd.com
Signed-off-by: Christian König <christian.koenig@amd.com>

drm/selftests: add drm buddy smoke testcase

- add a test to ascertain that the critical functionalities
  of the program is working fine
- add a timeout helper function

v2:
  - removed unnecessary test succeeded print
  - replace list_del()/list_add_tail() with list_move_tail()

Signed-off-by: Arunpravin <Arunpravin.PaneerSelvam@amd.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Acked-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220222174845.2175-6-Arunpravin.PaneerSelvam@amd.com
Signed-off-by: Christian König <christian.koenig@amd.com>

drm/selftests: add drm buddy pessimistic testcase

create a pot-sized mm, then allocate one of each possible
order within. This should leave the mm with exactly one
page left.

v2:
  - removed unnecessary test succeeded print
  - replace list_del()/list_add_tail() with list_move_tail()

Signed-off-by: Arunpravin <Arunpravin.PaneerSelvam@amd.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Acked-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220222174845.2175-5-Arunpravin.PaneerSelvam@amd.com
Signed-off-by: Christian König <christian.koenig@amd.com>

drm/selftests: add drm buddy optimistic testcase

create a mm with one block of each order available, and
try to allocate them all.

v2(Matthew Auld):
  - removed unnecessary test succeeded print
  - replace list_del()/list_add_tail() with list_move_tail()

Signed-off-by: Arunpravin <Arunpravin.PaneerSelvam@amd.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Acked-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220222174845.2175-4-Arunpravin.PaneerSelvam@amd.com
Signed-off-by: Christian König <christian.koenig@amd.com>

drm/selftests: add drm buddy alloc range testcase

- add a test to check the range allocation
- export get_buddy() function in drm_buddy.c
- export drm_prandom_u32_max_state() in lib/drm_random.c
- include helper functions
- include prime number header file

v2:
  - add drm_get_buddy() function description (Matthew Auld)
  - removed unnecessary test succeeded print

Signed-off-by: Arunpravin <Arunpravin.PaneerSelvam@amd.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Acked-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220222174845.2175-3-Arunpravin.PaneerSelvam@amd.com
Signed-off-by: Christian König <christian.koenig@amd.com>

drm/selftests: add drm buddy alloc limit testcase

add a test to check the maximum allocation limit

v2(Matthew Auld):
  - added err = -EINVAL in block NULL check
  - removed unnecessary test succeeded print

Signed-off-by: Arunpravin <Arunpravin.PaneerSelvam@amd.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Acked-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220222174845.2175-2-Arunpravin.PaneerSelvam@amd.com
Signed-off-by: Christian König <christian.koenig@amd.com>

drm/selftests: Move i915 buddy selftests into drm

- move i915 buddy selftests into drm selftests folder
- add Makefile and Kconfig support
- add sanitycheck testcase

Prerequisites
- These series of selftests patches are created on top of
  drm buddy series
- Enable kselftests for DRM as a module in .config

Signed-off-by: Arunpravin <Arunpravin.PaneerSelvam@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Acked-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220222174845.2175-1-Arunpravin.PaneerSelvam@amd.com
Signed-off-by: Christian König <christian.koenig@amd.com>

drm/sched: Add device pointer to drm_gpu_scheduler

Add device pointer so scheduler's printing can use
DRM_DEV_ERROR() instead, which makes life easier under multiple GPU
scenario.

v2: amend all calls of drm_sched_init()
v3: fill dev pointer for all drm_sched_init() calls

Signed-off-by: Jiawei Gu <Jiawei.Gu@amd.com>
Reviewed-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220221095705.5290-1-Jiawei.Gu@amd.com

drm: implement a method to free unused pages

On contiguous allocation, we round up the size
to the *next* power of 2, implement a function
to free the unused pages after the newly allocate block.

v2(Matthew Auld):
  - replace function name 'drm_buddy_free_unused_pages' with
    drm_buddy_block_trim
  - replace input argument name 'actual_size' with 'new_size'
  - add more validation checks for input arguments
  - add overlaps check to avoid needless searching and splitting
  - merged the below patch to see the feature in action
     - add free unused pages support to i915 driver
  - lock drm_buddy_block_trim() function as it calls mark_free/mark_split
    are all globally visible

v3(Matthew Auld):
  - remove trim method error handling as we address the failure case
    at drm_buddy_block_trim() function

v4:
  - in case of trim, at __alloc_range() split_block failure path
    marks the block as free and removes it from the original list,
    potentially also freeing it, to overcome this problem, we turn
    the drm_buddy_block_trim() input node into a temporary node to
    prevent recursively freeing itself, but still retain the
    un-splitting/freeing of the other nodes(Matthew Auld)

  - modify the drm_buddy_block_trim() function return type

v5(Matthew Auld):
  - revert drm_buddy_block_trim() function return type changes in v4
  - modify drm_buddy_block_trim() passing argument n_pages to original_size
    as n_pages has already been rounded up to the next power-of-two and
    passing n_pages results noop

v6:
  - fix warnings reported by kernel test robot <lkp@intel.com>

v7:
  - modify drm_buddy_block_trim() function doc description
  - at drm_buddy_block_trim() handle non-allocated block as
    a serious programmer error
  - fix a typo

Signed-off-by: Arunpravin <Arunpravin.PaneerSelvam@amd.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220221164552.2434-3-Arunpravin.PaneerSelvam@amd.com
Signed-off-by: Christian König <christian.koenig@amd.com>

drm: implement top-down allocation method

Implemented a function which walk through the order list,
compares the offset and returns the maximum offset block,
this method is unpredictable in obtaining the high range
address blocks which depends on allocation and deallocation.
for instance, if driver requests address at a low specific
range, allocator traverses from the root block and splits
the larger blocks until it reaches the specific block and
in the process of splitting, lower orders in the freelist
are occupied with low range address blocks and for the
subsequent TOPDOWN memory request we may return the low
range blocks.To overcome this issue, we may go with the
below approach.

The other approach, sorting each order list entries in
ascending order and compares the last entry of each
order list in the freelist and return the max block.
This creates sorting overhead on every drm_buddy_free()
request and split up of larger blocks for a single page
request.

v2:
  - Fix alignment issues(Matthew Auld)
  - Remove unnecessary list_empty check(Matthew Auld)
  - merged the below patch to see the feature in action
     - add top-down alloc support to i915 driver

Signed-off-by: Arunpravin <Arunpravin.PaneerSelvam@amd.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220221164552.2434-2-Arunpravin.PaneerSelvam@amd.com
Signed-off-by: Christian König <christian.koenig@amd.com>

drm: improve drm_buddy_alloc function

- Make drm_buddy_alloc a single function to handle
  range allocation and non-range allocation demands

- Implemented a new function alloc_range() which allocates
  the requested power-of-two block comply with range limitations

- Moved order computation and memory alignment logic from
  i915 driver to drm buddy

v2:
  merged below changes to keep the build unbroken
   - drm_buddy_alloc_range() becomes obsolete and may be removed
   - enable ttm range allocation (fpfn / lpfn) support in i915 driver
   - apply enhanced drm_buddy_alloc() function to i915 driver

v3(Matthew Auld):
  - Fix alignment issues and remove unnecessary list_empty check
  - add more validation checks for input arguments
  - make alloc_range() block allocations as bottom-up
  - optimize order computation logic
  - replace uint64_t with u64, which is preferred in the kernel

v4(Matthew Auld):
  - keep drm_buddy_alloc_range() function implementation for generic
    actual range allocations
  - keep alloc_range() implementation for end bias allocations

v5(Matthew Auld):
  - modify drm_buddy_alloc() passing argument place->lpfn to lpfn
    as place->lpfn will currently always be zero for i915

v6(Matthew Auld):
  - fixup potential uaf - If we are unlucky and can't allocate
    enough memory when splitting blocks, where we temporarily
    end up with the given block and its buddy on the respective
    free list, then we need to ensure we delete both blocks,
    and no just the buddy, before potentially freeing them

  - fix warnings reported by kernel test robot <lkp@intel.com>

v7(Matthew Auld):
  - revert fixup potential uaf
  - keep __alloc_range() add node to the list logic same as
    drm_buddy_alloc_blocks() by having a temporary list variable
  - at drm_buddy_alloc_blocks() keep i915 range_overflows macro
    and add a new check for end variable

v8:
  - fix warnings reported by kernel test robot <lkp@intel.com>

v9(Matthew Auld):
  - remove DRM_BUDDY_RANGE_ALLOCATION flag
  - remove unnecessary function description

v10:
   - keep DRM_BUDDY_RANGE_ALLOCATION flag as removing the flag
     and replacing with (end < size) logic fails amdgpu driver load

Signed-off-by: Arunpravin <Arunpravin.PaneerSelvam@amd.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220221164552.2434-1-Arunpravin.PaneerSelvam@amd.com

drm/vc4: Use drm_mode_copy()

struct drm_display_mode embeds a list head, so overwriting
the full struct with another one will corrupt the list
(if the destination mode is on a list). Use drm_mode_copy()
instead which explicitly preserves the list head of
the destination mode.

Even if we know the destination mode is not on any list
using drm_mode_copy() seems decent as it sets a good
example. Bad examples of not using it might eventually
get copied into code where preserving the list head
actually matters.

Obviously one case not covered here is when the mode
itself is embedded in a larger structure and the whole
structure is copied. But if we are careful when copying
into modes embedded in structures I think we can be a
little more reassured that bogus list heads haven't been
propagated in.

@is_mode_copy@
@@
drm_mode_copy(...)
{
...
}

@depends on !is_mode_copy@
struct drm_display_mode *mode;
expression E, S;
@@
(
- *mode = E
+ drm_mode_copy(mode, &E)
|
- memcpy(mode, E, S)
+ drm_mode_copy(mode, E)
)

@depends on !is_mode_copy@
struct drm_display_mode mode;
expression E;
@@
(
- mode = E
+ drm_mode_copy(&mode, &E)
|
- memcpy(&mode, E, S)
+ drm_mode_copy(&mode, E)
)

@@
struct drm_display_mode *mode;
@@
- &*mode
+ mode

Cc: Emma Anholt <emma@anholt.net>
Cc: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220218100403.7028-18-ville.syrjala@linux.intel.com

drm/panel: nt35560: Support also ACX424AKM

Add some code and config to also support the ACX424AKM used in
some Sony (Ericsson) Mobile phones.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220103113822.654592-3-linus.walleij@linaro.org

drm/panel: nt35560: Support more panel IDs

These IDs were found in the wild in a Sony Xperia vendor tree.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220103113822.654592-2-linus.walleij@linaro.org

drm/panel: Rename Sony ACX424 to Novatek NT35560

A code drop from Sony Mobile reveals that the ACX424 panels are
built around the Novatek NT35560 panel controllers so just bite
the bullet and rename the driver and all basic symbols so that
we can modify this driver to cover any other panels also using
the Novatek NT35560 display controller.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220103113822.654592-1-linus.walleij@linaro.org

drm/panel-edp: Add eDP sharp panel support

Add support for the 14" sharp,lq140m1jw46 eDP panel.

Signed-off-by: Sankeerth Billakanti <quic_sbillaka@quicinc.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1644494255-6632-5-git-send-email-quic_sbillaka@quicinc.com

dt-bindings: display: simple: Add sharp LQ140M1JW46 panel

Add support for sharp LQ140M1JW46 display panel. It is a 14" eDP panel
with 1920x1080 display resolution.

Signed-off-by: Sankeerth Billakanti <quic_sbillaka@quicinc.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1644494255-6632-2-git-send-email-quic_sbillaka@quicinc.com

fbdev: Don't sort deferred-I/O pages by default

Fbdev's deferred I/O sorts all dirty pages by default, which incurs a
significant overhead. Make the sorting step optional and update the few
drivers that require it. Use a FIFO list by default.

Most fbdev drivers with deferred I/O build a bounding rectangle around
the dirty pages or simply flush the whole screen. The only two affected
DRM drivers, generic fbdev and vmwgfx, both use a bounding rectangle.
In those cases, the exact order of the pages doesn't matter. The other
drivers look at the page index or handle pages one-by-one. The patch
sets the sort_pagelist flag for those, even though some of them would
probably work correctly without sorting. Driver maintainers should update
their driver accordingly.

Sorting pages by memory offset for deferred I/O performs an implicit
bubble-sort step on the list of dirty pages. The algorithm goes through
the list of dirty pages and inserts each new page according to its
index field. Even worse, list traversal always starts at the first
entry. As video memory is most likely updated scanline by scanline, the
algorithm traverses through the complete list for each updated page.

For example, with 1024x768x32bpp each page covers exactly one scanline.
Writing a single screen update from top to bottom requires updating
768 pages. With an average list length of 384 entries, a screen update
creates (768 * 384 =) 294912 compare operation.

Fix this by making the sorting step opt-in and update the few drivers
that require it. All other drivers work with unsorted page lists. Pages
are appended to the list. Therefore, in the common case of writing the
framebuffer top to bottom, pages are still sorted by offset, which may
have a positive effect on performance.

Playing a video [1] in mplayer's benchmark mode shows the difference
(i7-4790, FullHD, simpledrm, kernel with debugging).

  mplayer -benchmark -nosound -vo fbdev ./big_buck_bunny_720p_stereo.ogg

With sorted page lists:

  BENCHMARKs: VC:  32.960s VO:  73.068s A:   0.000s Sys:   2.413s =  108.441s
  BENCHMARK%: VC: 30.3947% VO: 67.3802% A:  0.0000% Sys:  2.2251% = 100.0000%

With unsorted page lists:

  BENCHMARKs: VC:  31.005s VO:  42.889s A:   0.000s Sys:   2.256s =   76.150s
  BENCHMARK%: VC: 40.7156% VO: 56.3219% A:  0.0000% Sys:  2.9625% = 100.0000%

VC shows the overhead of video decoding, VO shows the overhead of the
video output. Using unsorted page lists reduces the benchmark's run time
by ~32s/~25%.

v2:
* Make sorted pagelists the special case (Sam)
* Comment on drivers' use of pagelist (Sam)
* Warn about the overhead in comment

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://download.blender.org/peach/bigbuckbunny_movies/big_buck_bunny_720p_stereo.ogg
Link: https://patchwork.freedesktop.org/patch/msgid/20220211094640.21632-3-tzimmermann@suse.de

fbdev/defio: Early-out if page is already enlisted

Return early if a page is already in the list of dirty pages for
deferred I/O. This can be detected if the page's list head is not
empty. Keep the list head initialized while the page is not enlisted
to make this work reliably.

v2:
* update comment and fix spelling (Sam)

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220211094640.21632-2-tzimmermann@suse.de

dt-bindings: display: ssd1307fb: Add myself as binding co-maintainer

The ssd130x DRM driver also makes use of this Device Tree binding to allow
existing users of the fbdev driver to migrate without the need to change
their Device Trees.

Add myself as another maintainer of the binding, to make sure that I will
be on Cc when patches are proposed for it.

Suggested-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220214133935.3278933-1-javierm@redhat.com

MAINTAINERS: Add entry for Solomon SSD130x OLED displays DRM driver

To make sure that tools like the get_maintainer.pl script will suggest
to Cc me if patches are posted for this driver.

Also include the Device Tree binding for the old ssd1307fb fbdev driver
since the new DRM driver was made compatible with the existing binding.

Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220214133915.3278886-1-javierm@redhat.com

drm/solomon: Add SSD130x OLED displays I2C support

The ssd130x driver only provides the core support for these devices but it
does not have any bus transport logic. Add a driver to interface over I2C.

Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220214133710.3278506-5-javierm@redhat.com

drm: Add driver for Solomon SSD130x OLED displays

This adds a DRM driver for SSD1305, SSD1306, SSD1307 and SSD1309 Solomon
OLED display controllers.

It's only the core part of the driver and a bus specific driver is needed
for each transport interface supported by the display controllers.

Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220214133710.3278506-4-javierm@redhat.com

drm/format-helper: Add drm_fb_xrgb8888_to_mono_reversed()

Add support to convert from XR24 to reversed monochrome for drivers that
control monochromatic display panels, that only have 1 bit per pixel.

The function does a line-by-line conversion doing an intermediate step
first from XR24 to 8-bit grayscale and then to reversed monochrome.

The drm_fb_gray8_to_mono_reversed_line() helper was based on code from
drivers/gpu/drm/tiny/repaper.c driver.

Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220214133710.3278506-3-javierm@redhat.com

drm/format-helper: Add drm_fb_xrgb8888_to_gray8_line()

Pull the per-line conversion logic into a separate helper function.

This will allow to do line-by-line conversion in other helpers that
convert to a gray8 format.

Suggested-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220214133710.3278506-2-javierm@redhat.com

drm/modes: Fix drm_mode_copy() docs

There is no object id in drm_display_mode anymore.
Remove stale comments to the contrary.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220209091928.14766-2-ville.syrjala@linux.intel.com
Acked-by: Maxime Ripard <maxime@cerno.tech>

drm/vc4: Use of_device_get_match_data()

Use of_device_get_match_data() to simplify the code.

Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi (CGEL ZTE) <chi.minghao@zte.com.cn>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220214020530.1714631-1-chi.minghao@zte.com.cn

drm/panel-edp: Allow querying the detected panel via debugfs

Recently we added generic "edp-panel"s probed by EDID. To support
panels in this way we look at the panel ID in the EDID and look up the
panel in a table that has power sequence timings. If we find a panel
that's not in the table we will still attempt to use it but we'll use
conservative timings. While it's likely that these conservative
timings will work for most nearly all panels, the performance of
turning the panel off and on suffers.

We'd like to be able to reliably detect the case that we're using the
hardcoded timings without relying on parsing dmesg. This allows us to
implement tests that ensure that no devices get shipped that are
relying on the conservative timings.

Let's add a new debugfs entry to panel devices. It will have one of:
* UNKNOWN - We tried to detect a panel but it wasn't in our table.
* HARDCODED - We're not using generic "edp-panel" probed by EDID.
* A panel name - This is the name of the panel from our table.

Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220204161245.v2.3.I209d72bcc571e1d7d6b793db71bf15c9c0fc9292@changeid

drm: Plumb debugfs_init through to panels

We'd like panels to be able to add things to debugfs underneath the
connector's directory. Let's plumb it through. A panel will be able to
put things in a "panel" directory under the connector's
directory. Note that debugfs is not ABI and so it's always possible
that the location that the panel gets for its debugfs could change in
the future.

NOTE: this currently only works if you're using a modern
architecture. Specifically the plumbing relies on _both_
drm_bridge_connector and drm_panel_bridge. If you're not using one or
both of these things then things won't be plumbed through.

As a side effect of this change, drm_bridges can also get callbacks to
put stuff underneath the connector's debugfs directory. At the moment
all bridges in the chain have their debugfs_init() called with the
connector's root directory.

Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220204161245.v2.2.Ib0bd5346135cbb0b63006b69b61d4c8af6484740@changeid

drm/bridge: ti-sn65dsi86: Use drm_bridge_connector

The ti-sn65dsi86 driver shouldn't hand-roll its own bridge
connector. It should use the normal drm_bridge_connector. Let's switch
to do that, removing all of the custom code.

NOTE: this still _doesn't_ implement DRM_BRIDGE_ATTACH_NO_CONNECTOR
support for ti-sn65dsi86 and that would still be a useful thing to do
in the future. It was attempted in the past [1] but put on the back
burner. However, unless we instantly change ti-sn65dsi86 fully from
not supporting DRM_BRIDGE_ATTACH_NO_CONNECTOR at all to _only_
supporting DRM_BRIDGE_ATTACH_NO_CONNECTOR then we'll still need a bit
of time when we support both. This is a better way to support the old
way where the driver hand rolls things itself.

A new notes about the implementation here:
* When using the drm_bridge_connector the connector should be created
  after all the bridges, so we change the ordering a bit.
* I'm reasonably certain that we don't need to do anything to "free"
  the new drm_bridge_connector. If drm_bridge_connector_init() returns
  success then we know drm_connector_init() was called with the
  `drm_bridge_connector_funcs`. The `drm_bridge_connector_funcs` has a
  .destroy() that does all the cleanup. drm_connector_init() calls
  __drm_mode_object_add() with a drm_connector_free() that will call
  the .destroy().
* I'm also reasonably certain that I don't need to "undo" the
  drm_bridge_attach() if drm_bridge_connector_init() fails. The
  "detach" function is private and other similar code doesn't try to
  undo the drm_bridge_attach() in error cases. There's also a comment
  indicating the lack of balance at the top of drm_bridge_attach().

[1] https://lore.kernel.org/r/20210920225801.227211-4-robdclark@gmail.com

Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220204161245.v2.1.I3ab26b7f197cc56c874246a43e57913e9c2c1028@changeid

drm/radeon: remove resource accounting v2

Use the one provided by TTM instead.

v2: drop new_mem parameter as well

Signed-off-by: Christian König <christian.koenig@amd.com>
Tested-by: Bas Nieuwenhuizen <bas@basnieuwenhuizen.nl>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220214093439.2989-5-christian.koenig@amd.com

drm/bridge: anx7625: Fix overflow issue on reading EDID

The length of EDID block can be longer than 256 bytes, so we should use
`int` instead of `u8` for the `edid_pos` variable.

Fixes: 8bdfc5dae4e3 ("drm/bridge: anx7625: Add anx7625 MIPI DSI/DPI to DP")
Signed-off-by: Pin-Yen Lin <treapking@chromium.org>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220210103827.402436-1-treapking@chromium.org

drm/amdgpu: remove VRAM accounting v2

This is provided by TTM now.

Also switch man->size to bytes instead of pages and fix the double
printing of size and usage in debugfs.

v2: fix size checking as well

Signed-off-by: Christian König <christian.koenig@amd.com>
Tested-by: Bas Nieuwenhuizen <bas@basnieuwenhuizen.nl>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220214093439.2989-8-christian.koenig@amd.com

drm/amdgpu: remove PL_PREEMPT accounting

This is provided by TTM now.

Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220214093439.2989-7-christian.koenig@amd.com

drm/amdgpu: remove GTT accounting v2

This is provided by TTM now.

Also switch man->size to bytes instead of pages and fix the double
printing of size and usage in debugfs.

v2: fix size checking as well

Signed-off-by: Christian König <christian.koenig@amd.com>
Tested-by: Bas Nieuwenhuizen <bas@basnieuwenhuizen.nl>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220214093439.2989-6-christian.koenig@amd.com

drm/sprd: check the platform_get_resource() return value

platform_get_resource() may fail and return NULL, so check it's value
before using it.

Reported-by: Zou Wei <zou_wei@huawei.com>
Signed-off-by: Kevin Tang <kevin3.tang@gmail.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://lore.kernel.org/all/20220117084156.9338-1-kevin3.tang@gmail.com
v1 -> v2:
- new patch

drm/sprd: fix potential NULL dereference

'drm' could be null in sprd_drm_shutdown, and drm_warn maybe dereference
it, remove this warning log.

Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kevin Tang <kevin3.tang@gmail.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://lore.kernel.org/all/20220117084044.9210-1-kevin3.tang@gmail.com
v1 -> v2:
- Split checking platform_get_resource() return value to a separate patch
- Use dev_warn() instead of removing the warning log

drm/sprd: remove the selected DRM_KMS_CMA_HELPER in kconfig

On commit 43531edd53f0 ("drm/sprd: add Unisoc's drm kms master"),
adds the config DRM_SPRD, which selects DRM_KMS_CMA_HELPER.

However, commit 09717af7d13d ("drm: Remove CONFIG_DRM_KMS_CMA_HELPER
option") just removed the DRM_KMS_CMA_HELPER.
So the select DRM_KMS_CMA_HELPER refers to a non-existing kconfig symbol.

Reported-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: Kevin Tang <kevin3.tang@gmail.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Link: https://lore.kernel.org/all/20220117083820.6893-2-kevin3.tang@gmail.com
v1 -> v2:
- fix commit comments long lines issue and drop "On linux-next" comments

drm/ttm: add common accounting to the resource mgr v3

It makes sense to have this in the common manager for debugging and
accounting of how much resources are used.

v2: cleanup kerneldoc a bit
v3: drop the atomic, update counter under lock instead

Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com> (v1)
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Tested-by: Bas Nieuwenhuizen <bas@basnieuwenhuizen.nl>
Link: https://patchwork.freedesktop.org/patch/msgid/20220214093439.2989-2-christian.koenig@amd.com

drm/ttm: fix resource manager size type and description

Leave the man->size units as driver defined.

Signed-off-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220214093439.2989-1-christian.koenig@amd.com
Reviewed-by: Matthew Auld <matthew.auld@intel.com>

dt-bindings: drm/bridge: anx7625: Add aux-bus node

List panel under aux-bus node if it's connected to anx7625's aux bus.

Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220213103437.3363848-4-hsinyi@chromium.org

drm/bridge: anx7625: Support reading edid through aux channel

Support reading edid through aux channel if panel is connected to aux
bus. Extend anx7625_aux_dpcd_trans() to implement aux transfer function:

1. panel is populated in devm_of_dp_aux_populate_ep_devices(), so move
   anx7625_parse_dt() after.
2. Use pm runtime autosuspend since aux transfer function is called
   multiple times when reading edid.
3. No-op if aux transfer length is 0.

Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: Xin Ji <xji@analogixsemi.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220213103437.3363848-3-hsinyi@chromium.org

drm/bridge: anx7625: Convert to use devm_kzalloc

Use devm_kzalloc instead of kzalloc and drop kfree(). Let the memory
handled by driver detach.

Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: Xin Ji <xji@analogixsemi.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220213103437.3363848-2-hsinyi@chromium.org

drm/bridge: anx7625: send DPCD command to downstream

Send DPCD command to downstream before anx7625 power down,
let downstream monitor enter into standby mode.

Signed-off-by: Xin Ji <xji@analogixsemi.com>
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: Hsin-Yi Wang <hsinyi@chromium.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220213103437.3363848-1-hsinyi@chromium.org

drm/ingenic: Fix support for JZ4780 HDMI output

We have to make sure that
- JZ_LCD_OSDC_ALPHAEN is set
- plane f0 is disabled as it's not working yet

Tested on MIPS Creator CI20 board.

Signed-off-by: Paul Boddie <paul@boddie.org.uk>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Fixes: ef2f5d0aa121 ("drm/ingenic: prepare ingenic drm for later addition of JZ4780")
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
[pcercuei: add proper fixes commit, slightly reword commit description]
Link: https://patchwork.freedesktop.org/patch/msgid/9d3a2000d2bb014f1afb0613537bdc523202135d.1644681054.git.hns@goldelico.com

drm/gem-shmem: Don't store mmap'ed buffers in core dumps

Set the VM_DONTDUMP flag on mmap'ed VMAs to omit them from core
dumps. It's display-buffer memory; who knows what secrets these
buffers contain.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Chia-I Wu <olvaffe@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220209155634.3994-3-tzimmermann@suse.de

drm/gem-shmem: Set vm_ops in static initializer

Initialize default vm_ops in static initialization of the GEM SHMEM funcs,
instead of the mmap code. It's simply better style. GEM helpers will later
set a VMA's vm_ops from the default automatically.

v2:
* also update the drivers that build upon GEM SHMEM

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Steven Price <steven.price@arm.com>
Reviewed-by: Chia-I Wu <olvaffe@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220209155634.3994-2-tzimmermann@suse.de

dt-bindings: display: Add ingenic,jz4780-dw-hdmi DT Schema

Add DT bindings for the hdmi driver for the Ingenic JZ4780 SoC.
Based on .txt binding from Zubair Lutfullah Kakakhel

Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Cc: Rob Herring <robh@kernel.org>
Cc: devicetree@vger.kernel.org
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://patchwork.freedesktop.org/patch/msgid/c806c6007f7bb090bf96ff6bd827f03e88bf4712.1644675566.git.hns@goldelico.com

drm/lima: avoid error task dump attempt when not enabled

Currently when users try to run an application with lima and that hits
an issue such as a timeout, a message saying "fail to save task state"
and "error task list is full" is shown in dmesg.

The error task dump is a debug feature disabled by default, so the
error task list is usually not going to be available at all.
The message can be misleading and creates confusion in bug reports.

We can avoid that code path and that particular message when the user
has not explicitly set the max_error_tasks parameter to enable the
feature.

Signed-off-by: Erico Nunes <nunes.erico@gmail.com>
Reviewed-by: Qiang Yu <yuq825@gmail.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Qiang Yu <yuq825@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220209093700.30901-1-nunes.erico@gmail.com

drm/amdgpu: Fix htmldoc warning

Update function name.

Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220211205500.601391-1-andrey.grodzovsky@amd.com