From: Jani Nikula Date: Wed, 29 Aug 2012 11:08:42 +0000 (+0300) Subject: drm/i915: only enable sdvo hotplug irq if needed X-Git-Tag: v3.6~80^2~5^2~4 X-Git-Url: http://review.tizen.org/git/?a=commitdiff_plain;h=fcbc50da7753b210b4442ca9abc4efbd4e481f6e;p=platform%2Fkernel%2Flinux-amlogic.git drm/i915: only enable sdvo hotplug irq if needed Avoid constant wakeups caused by noisy irq lines when we don't even care about the irq. This should be particularly useful for i945g/gm where the hotplug has been disabled: commit 768b107e4b3be0acf6f58e914afe4f337c00932b Author: Daniel Vetter Date: Fri May 4 11:29:56 2012 +0200 drm/i915: disable sdvo hotplug on i945g/gm v2: While at it, remove the bogus hotplug_active read, and do not mask hotplug_active[0] before checking whether the irq is needed, per discussion with Daniel on IRC. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=38442 Tested-by: Dominik Köppl Signed-off-by: Jani Nikula Cc: stable@vger.kernel.org Signed-off-by: Daniel Vetter --- diff --git a/drivers/gpu/drm/i915/intel_sdvo.c b/drivers/gpu/drm/i915/intel_sdvo.c index d81bb0b..123afd3 100644 --- a/drivers/gpu/drm/i915/intel_sdvo.c +++ b/drivers/gpu/drm/i915/intel_sdvo.c @@ -2573,7 +2573,6 @@ bool intel_sdvo_init(struct drm_device *dev, uint32_t sdvo_reg, bool is_sdvob) hotplug_mask = intel_sdvo->is_sdvob ? SDVOB_HOTPLUG_INT_STATUS_I915 : SDVOC_HOTPLUG_INT_STATUS_I915; } - dev_priv->hotplug_supported_mask |= hotplug_mask; drm_encoder_helper_add(&intel_encoder->base, &intel_sdvo_helper_funcs); @@ -2581,14 +2580,6 @@ bool intel_sdvo_init(struct drm_device *dev, uint32_t sdvo_reg, bool is_sdvob) if (!intel_sdvo_get_capabilities(intel_sdvo, &intel_sdvo->caps)) goto err; - /* Set up hotplug command - note paranoia about contents of reply. - * We assume that the hardware is in a sane state, and only touch - * the bits we think we understand. - */ - intel_sdvo_get_value(intel_sdvo, SDVO_CMD_GET_ACTIVE_HOT_PLUG, - &intel_sdvo->hotplug_active, 2); - intel_sdvo->hotplug_active[0] &= ~0x3; - if (intel_sdvo_output_setup(intel_sdvo, intel_sdvo->caps.output_flags) != true) { DRM_DEBUG_KMS("SDVO output failed to setup on %s\n", @@ -2596,6 +2587,12 @@ bool intel_sdvo_init(struct drm_device *dev, uint32_t sdvo_reg, bool is_sdvob) goto err; } + /* Only enable the hotplug irq if we need it, to work around noisy + * hotplug lines. + */ + if (intel_sdvo->hotplug_active[0]) + dev_priv->hotplug_supported_mask |= hotplug_mask; + intel_sdvo_select_ddc_bus(dev_priv, intel_sdvo, sdvo_reg); /* Set the input timing to the screen. Assume always input 0. */