From: Vladimir Oltean Date: Thu, 2 May 2019 20:23:32 +0000 (+0300) Subject: net: dsa: sja1105: Error out if RGMII delays are requested in DT X-Git-Tag: v5.4-rc1~1056^2~58^2~8 X-Git-Url: http://review.tizen.org/git/?a=commitdiff_plain;h=f5b8631c293b9a88e38a152fa9a67f89e2d9b151;p=platform%2Fkernel%2Flinux-rpi.git net: dsa: sja1105: Error out if RGMII delays are requested in DT Documentation/devicetree/bindings/net/ethernet.txt is confusing because it says what the MAC should not do, but not what it *should* do: * "rgmii-rxid" (RGMII with internal RX delay provided by the PHY, the MAC should not add an RX delay in this case) The gap in semantics is threefold: 1. Is it illegal for the MAC to apply the Rx internal delay by itself, and simplify the phy_mode (mask off "rgmii-rxid" into "rgmii") before passing it to of_phy_connect? The documentation would suggest yes. 1. For "rgmii-rxid", while the situation with the Rx clock skew is more or less clear (needs to be added by the PHY), what should the MAC driver do about the Tx delays? Is it an implicit wild card for the MAC to apply delays in the Tx direction if it can? What if those were already added as serpentine PCB traces, how could that be made more obvious through DT bindings so that the MAC doesn't attempt to add them twice and again potentially break the link? 3. If the interface is a fixed-link and therefore the PHY object is fixed (a purely software entity that obviously cannot add clock skew), what is the meaning of the above property? So an interpretation of the RGMII bindings was chosen that hopefully does not contradict their intention but also makes them more applied. The SJA1105 driver understands to act upon "rgmii-*id" phy-mode bindings if the port is in the PHY role (either explicitly, or if it is a fixed-link). Otherwise it always passes the duty of setting up delays to the PHY driver. The error behavior that this patch adds is required on SJA1105E/T where the MAC really cannot apply internal delays. If the other end of the fixed-link cannot apply RGMII delays either (this would be specified through its own DT bindings), then the situation requires PCB delays. For SJA1105P/Q/R/S, this is however hardware supported and the error is thus only temporary. I created a stub function pointer for configuring delays per-port on RXC and TXC, and will implement it when I have access to a board with this hardware setup. Meanwhile do not allow the user to select an invalid configuration. Signed-off-by: Vladimir Oltean Reviewed-by: Florian Fainelli Reviewed-by: Andrew Lunn Signed-off-by: David S. Miller --- diff --git a/drivers/net/dsa/sja1105/sja1105.h b/drivers/net/dsa/sja1105/sja1105.h index 50ab928..87dee67 100644 --- a/drivers/net/dsa/sja1105/sja1105.h +++ b/drivers/net/dsa/sja1105/sja1105.h @@ -48,11 +48,14 @@ struct sja1105_info { const struct sja1105_table_ops *static_ops; const struct sja1105_regs *regs; int (*reset_cmd)(const void *ctx, const void *data); + int (*setup_rgmii_delay)(const void *ctx, int port); const char *name; }; struct sja1105_private { struct sja1105_static_config static_config; + bool rgmii_rx_delay[SJA1105_NUM_PORTS]; + bool rgmii_tx_delay[SJA1105_NUM_PORTS]; const struct sja1105_info *info; struct gpio_desc *reset_gpio; struct spi_device *spidev; diff --git a/drivers/net/dsa/sja1105/sja1105_clocking.c b/drivers/net/dsa/sja1105/sja1105_clocking.c index 5985442..94bfe0e 100644 --- a/drivers/net/dsa/sja1105/sja1105_clocking.c +++ b/drivers/net/dsa/sja1105/sja1105_clocking.c @@ -427,7 +427,10 @@ static int sja1105_rgmii_clocking_setup(struct sja1105_private *priv, int port) dev_err(dev, "Failed to configure Tx pad registers\n"); return rc; } - return 0; + if (!priv->info->setup_rgmii_delay) + return 0; + + return priv->info->setup_rgmii_delay(priv, port); } static int sja1105_cgu_rmii_ref_clk_config(struct sja1105_private *priv, diff --git a/drivers/net/dsa/sja1105/sja1105_main.c b/drivers/net/dsa/sja1105/sja1105_main.c index ec8137e..d27b9c1 100644 --- a/drivers/net/dsa/sja1105/sja1105_main.c +++ b/drivers/net/dsa/sja1105/sja1105_main.c @@ -518,6 +518,30 @@ static int sja1105_static_config_load(struct sja1105_private *priv, return sja1105_static_config_upload(priv); } +static int sja1105_parse_rgmii_delays(struct sja1105_private *priv, + const struct sja1105_dt_port *ports) +{ + int i; + + for (i = 0; i < SJA1105_NUM_PORTS; i++) { + if (ports->role == XMII_MAC) + continue; + + if (ports->phy_mode == PHY_INTERFACE_MODE_RGMII_RXID || + ports->phy_mode == PHY_INTERFACE_MODE_RGMII_ID) + priv->rgmii_rx_delay[i] = true; + + if (ports->phy_mode == PHY_INTERFACE_MODE_RGMII_TXID || + ports->phy_mode == PHY_INTERFACE_MODE_RGMII_ID) + priv->rgmii_tx_delay[i] = true; + + if ((priv->rgmii_rx_delay[i] || priv->rgmii_tx_delay[i]) && + !priv->info->setup_rgmii_delay) + return -EINVAL; + } + return 0; +} + static int sja1105_parse_ports_node(struct sja1105_private *priv, struct sja1105_dt_port *ports, struct device_node *ports_node) @@ -959,6 +983,16 @@ static int sja1105_setup(struct dsa_switch *ds) dev_err(ds->dev, "Failed to parse DT: %d\n", rc); return rc; } + + /* Error out early if internal delays are required through DT + * and we can't apply them. + */ + rc = sja1105_parse_rgmii_delays(priv, ports); + if (rc < 0) { + dev_err(ds->dev, "RGMII delay not supported\n"); + return rc; + } + /* Create and send configuration down to device */ rc = sja1105_static_config_load(priv, ports); if (rc < 0) {