From: Ji-Ze Hong (Peter Hong) <hpeter@gmail.com>
Date: Thu, 11 Jan 2018 06:47:16 +0000 (+0800)
Subject: USB: serial: f81534: add auto RTS direction support
X-Git-Tag: v4.19~1693^2~27^2~4
X-Git-Url: http://review.tizen.org/git/?a=commitdiff_plain;h=ee0309b46a20304d30c0e0447a2da2a94115731c;p=platform%2Fkernel%2Flinux-rpi.git

USB: serial: f81534: add auto RTS direction support

The F81532/534 had auto RTS direction support for RS485 mode.
We'll read it from internal Flash with address 0x2f01~0x2f04 for 4 ports.
There are 4 conditions below:
	0: F81534_PORT_CONF_RS232.
	1: F81534_PORT_CONF_RS485.
	2: value error, default to F81534_PORT_CONF_RS232.
	3: F81534_PORT_CONF_RS485_INVERT.

F81532/534 Clock register (offset +08h)

Bit0:	UART Enable (always on)
Bit2-1:	Clock source selector
			00: 1.846MHz.
			01: 18.46MHz.
			10: 24MHz.
			11: 14.77MHz.
Bit4:	Auto direction(RTS) control (RTS pin Low when TX)
Bit5:	Invert direction(RTS) when Bit4 enabled (RTS pin high when TX)

Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
[ johan: rename mode-mask define, and only use GENMASK() for masks ]
Signed-off-by: Johan Hovold <johan@kernel.org>
---

diff --git a/drivers/usb/serial/f81534.c b/drivers/usb/serial/f81534.c
index cfba054..5caa945 100644
--- a/drivers/usb/serial/f81534.c
+++ b/drivers/usb/serial/f81534.c
@@ -98,11 +98,16 @@
 
 #define F81534_DEFAULT_BAUD_RATE	9600
 
+#define F81534_PORT_CONF_RS232		0
+#define F81534_PORT_CONF_RS485		BIT(0)
+#define F81534_PORT_CONF_RS485_INVERT	(BIT(0) | BIT(1))
+#define F81534_PORT_CONF_MODE_MASK	GENMASK(1, 0)
 #define F81534_PORT_CONF_DISABLE_PORT	BIT(3)
 #define F81534_PORT_CONF_NOT_EXIST_PORT	BIT(7)
 #define F81534_PORT_UNAVAILABLE		\
 	(F81534_PORT_CONF_DISABLE_PORT | F81534_PORT_CONF_NOT_EXIST_PORT)
 
+
 #define F81534_1X_RXTRIGGER		0xc3
 #define F81534_8X_RXTRIGGER		0xcf
 
@@ -115,6 +120,8 @@
  *			01: 18.46MHz.
  *			10: 24MHz.
  *			11: 14.77MHz.
+ * Bit4:	Auto direction(RTS) control (RTS pin Low when TX)
+ * Bit5:	Invert direction(RTS) when Bit4 enabled (RTS pin high when TX)
  */
 
 #define F81534_UART_EN			BIT(0)
@@ -123,6 +130,8 @@
 #define F81534_CLK_24_MHZ		BIT(2)
 #define F81534_CLK_14_77_MHZ		(BIT(1) | BIT(2))
 #define F81534_CLK_MASK			GENMASK(2, 1)
+#define F81534_CLK_RS485_MODE		BIT(4)
+#define F81534_CLK_RS485_INVERT		BIT(5)
 
 static const struct usb_device_id f81534_id_table[] = {
 	{ USB_DEVICE(FINTEK_VENDOR_ID_1, FINTEK_DEVICE_ID) },
@@ -1274,9 +1283,12 @@ static void f81534_lsr_worker(struct work_struct *work)
 
 static int f81534_port_probe(struct usb_serial_port *port)
 {
+	struct f81534_serial_private *serial_priv;
 	struct f81534_port_private *port_priv;
 	int ret;
+	u8 value;
 
+	serial_priv = usb_get_serial_data(port->serial);
 	port_priv = devm_kzalloc(&port->dev, sizeof(*port_priv), GFP_KERNEL);
 	if (!port_priv)
 		return -ENOMEM;
@@ -1309,6 +1321,24 @@ static int f81534_port_probe(struct usb_serial_port *port)
 	if (ret)
 		return ret;
 
+	value = serial_priv->conf_data[port_priv->phy_num];
+	switch (value & F81534_PORT_CONF_MODE_MASK) {
+	case F81534_PORT_CONF_RS485_INVERT:
+		port_priv->shadow_clk |= F81534_CLK_RS485_MODE |
+					F81534_CLK_RS485_INVERT;
+		dev_dbg(&port->dev, "RS485 invert mode\n");
+		break;
+	case F81534_PORT_CONF_RS485:
+		port_priv->shadow_clk |= F81534_CLK_RS485_MODE;
+		dev_dbg(&port->dev, "RS485 mode\n");
+		break;
+
+	default:
+	case F81534_PORT_CONF_RS232:
+		dev_dbg(&port->dev, "RS232 mode\n");
+		break;
+	}
+
 	return 0;
 }