From: Bryan Wu Date: Thu, 17 Dec 2009 03:04:02 +0000 (-0500) Subject: usb: musb: add support for Blackfin MUSB X-Git-Tag: v2010.03-rc1~159^2~5 X-Git-Url: http://review.tizen.org/git/?a=commitdiff_plain;h=e608f221c13943d88e86f44753e23668342c3df3;p=platform%2Fkernel%2Fu-boot.git usb: musb: add support for Blackfin MUSB Signed-off-by: Bryan Wu Signed-off-by: Cliff Cai Signed-off-by: Mike Frysinger Signed-off-by: Remy Bohmer --- diff --git a/drivers/usb/musb/Makefile b/drivers/usb/musb/Makefile index 12e115e..397f5fe 100644 --- a/drivers/usb/musb/Makefile +++ b/drivers/usb/musb/Makefile @@ -27,6 +27,7 @@ LIB := $(obj)libusb_musb.a COBJS-$(CONFIG_MUSB_HCD) += musb_hcd.o musb_core.o COBJS-$(CONFIG_MUSB_UDC) += musb_udc.o musb_core.o +COBJS-$(CONFIG_USB_BLACKFIN) += blackfin_usb.o COBJS-$(CONFIG_USB_DAVINCI) += davinci.o COBJS-$(CONFIG_USB_OMAP3) += omap3.o COBJS-$(CONFIG_USB_DA8XX) += da8xx.o diff --git a/drivers/usb/musb/blackfin_usb.c b/drivers/usb/musb/blackfin_usb.c new file mode 100644 index 0000000..38aceb2 --- /dev/null +++ b/drivers/usb/musb/blackfin_usb.c @@ -0,0 +1,143 @@ +/* + * Blackfin MUSB HCD (Host Controller Driver) for u-boot + * + * Copyright (c) 2008-2009 Analog Devices Inc. + * + * Licensed under the GPL-2 or later. + */ + +#include + +#include + +#include +#include + +#include "musb_core.h" + +/* MUSB platform configuration */ +struct musb_config musb_cfg = { + .regs = (struct musb_regs *)USB_FADDR, + .timeout = 0x3FFFFFF, + .musb_speed = 0, +}; + +/* + * This function read or write data to endpoint fifo + * Blackfin use DMA polling method to avoid buffer alignment issues + * + * ep - Endpoint number + * length - Number of bytes to write to FIFO + * fifo_data - Pointer to data buffer to be read/write + * is_write - Flag for read or write + */ +void rw_fifo(u8 ep, u32 length, void *fifo_data, int is_write) +{ + struct bfin_musb_dma_regs *regs; + u32 val = (u32)fifo_data; + + blackfin_dcache_flush_invalidate_range(fifo_data, fifo_data + length); + + regs = (void *)USB_DMA_INTERRUPT; + regs += ep; + + /* Setup DMA address register */ + bfin_write16(®s->addr_low, val); + SSYNC(); + + bfin_write16(®s->addr_high, val >> 16); + SSYNC(); + + /* Setup DMA count register */ + bfin_write16(®s->count_low, length); + bfin_write16(®s->count_high, 0); + SSYNC(); + + /* Enable the DMA */ + val = (ep << 4) | DMA_ENA | INT_ENA; + if (is_write) + val |= DIRECTION; + bfin_write16(®s->control, val); + SSYNC(); + + /* Wait for compelete */ + while (!(bfin_read_USB_DMA_INTERRUPT() & (1 << ep))) + continue; + + /* acknowledge dma interrupt */ + bfin_write_USB_DMA_INTERRUPT(1 << ep); + SSYNC(); + + /* Reset DMA */ + bfin_write16(®s->control, 0); + SSYNC(); +} + +void write_fifo(u8 ep, u32 length, void *fifo_data) +{ + rw_fifo(ep, length, fifo_data, 1); +} + +void read_fifo(u8 ep, u32 length, void *fifo_data) +{ + rw_fifo(ep, length, fifo_data, 0); +} + + +/* + * CPU and board-specific MUSB initializations. Aliased function + * signals caller to move on. + */ +static void __def_musb_init(void) +{ +} +void board_musb_init(void) __attribute__((weak, alias("__def_musb_init"))); + +int musb_platform_init(void) +{ + /* board specific initialization */ + board_musb_init(); + + if (ANOMALY_05000346) { + bfin_write_USB_APHY_CALIB(ANOMALY_05000346_value); + SSYNC(); + } + + if (ANOMALY_05000347) { + bfin_write_USB_APHY_CNTRL(0x0); + SSYNC(); + } + + /* Configure PLL oscillator register */ + bfin_write_USB_PLLOSC_CTRL(0x30a8); + SSYNC(); + + bfin_write_USB_SRP_CLKDIV((get_sclk()/1000) / 32 - 1); + SSYNC(); + + bfin_write_USB_EP_NI0_RXMAXP(64); + SSYNC(); + + bfin_write_USB_EP_NI0_TXMAXP(64); + SSYNC(); + + /* Route INTRUSB/INTR_RX/INTR_TX to USB_INT0*/ + bfin_write_USB_GLOBINTR(0x7); + SSYNC(); + + bfin_write_USB_GLOBAL_CTL(GLOBAL_ENA | EP1_TX_ENA | EP2_TX_ENA | + EP3_TX_ENA | EP4_TX_ENA | EP5_TX_ENA | + EP6_TX_ENA | EP7_TX_ENA | EP1_RX_ENA | + EP2_RX_ENA | EP3_RX_ENA | EP4_RX_ENA | + EP5_RX_ENA | EP6_RX_ENA | EP7_RX_ENA); + SSYNC(); + + return 0; +} + +/* + * This function performs Blackfin platform specific deinitialization for usb. +*/ +void musb_platform_deinit(void) +{ +} diff --git a/drivers/usb/musb/blackfin_usb.h b/drivers/usb/musb/blackfin_usb.h new file mode 100644 index 0000000..ab26ca2 --- /dev/null +++ b/drivers/usb/musb/blackfin_usb.h @@ -0,0 +1,99 @@ +/* + * Blackfin MUSB HCD (Host Controller Driver) for u-boot + * + * Copyright (c) 2008-2009 Analog Devices Inc. + * + * Licensed under the GPL-2 or later. + */ + +#ifndef __BLACKFIN_USB_H__ +#define __BLACKFIN_USB_H__ + +#include + +/* Every register is 32bit aligned, but only 16bits in size */ +#define ureg(name) u16 name; u16 __pad_##name; + +#define musb_regs musb_regs +struct musb_regs { + /* common registers */ + ureg(faddr) + ureg(power) + ureg(intrtx) + ureg(intrrx) + ureg(intrtxe) + ureg(intrrxe) + ureg(intrusb) + ureg(intrusbe) + ureg(frame) + ureg(index) + ureg(testmode) + ureg(globintr) + ureg(global_ctl) + u32 reserved0[3]; + /* indexed registers */ + ureg(txmaxp) + ureg(txcsr) + ureg(rxmaxp) + ureg(rxcsr) + ureg(rxcount) + ureg(txtype) + ureg(txinterval) + ureg(rxtype) + ureg(rxinterval) + u32 reserved1; + ureg(txcount) + u32 reserved2[5]; + /* fifo */ + u16 fifox[32]; + /* OTG, dynamic FIFO, version & vendor registers */ + u32 reserved3[16]; + ureg(devctl) + ureg(vbus_irq) + ureg(vbus_mask) + u32 reserved4[15]; + ureg(linkinfo) + ureg(vplen) + ureg(hseof1) + ureg(fseof1) + ureg(lseof1) + u32 reserved5[41]; + /* target address registers */ + struct musb_tar_regs { + ureg(txmaxp) + ureg(txcsr) + ureg(rxmaxp) + ureg(rxcsr) + ureg(rxcount) + ureg(txtype) + ureg(txinternal) + ureg(rxtype) + ureg(rxinternal) + u32 reserved6; + ureg(txcount) + u32 reserved7[5]; + } tar[8]; +} __attribute__((packed)); + +struct bfin_musb_dma_regs { + ureg(interrupt); + ureg(control); + ureg(addr_low); + ureg(addr_high); + ureg(count_low); + ureg(count_high); + ureg(pad); +}; + +#undef ureg + +/* EP5-EP7 are the only ones with 1024 byte FIFOs which BULK really needs */ +#define MUSB_BULK_EP 5 + +/* Blackfin FIFO's are static */ +#define MUSB_NO_DYNAMIC_FIFO + +/* No HUB support :( */ +#define MUSB_NO_MULTIPOINT + +#endif diff --git a/drivers/usb/musb/musb_core.h b/drivers/usb/musb/musb_core.h index cee7a11..f0f0301 100644 --- a/drivers/usb/musb/musb_core.h +++ b/drivers/usb/musb/musb_core.h @@ -38,6 +38,10 @@ #include #include +#ifdef CONFIG_USB_BLACKFIN +# include "blackfin_usb.h" +#endif + #define MUSB_EP0_FIFOSIZE 64 /* This is non-configurable */ /* EP0 */ @@ -71,6 +75,7 @@ struct musb_epN_regs { }; /* Mentor USB core register overlay structure */ +#ifndef musb_regs struct musb_regs { /* common registers */ u8 faddr; @@ -138,6 +143,7 @@ struct musb_regs { } ep[16]; } __attribute__((packed, aligned(32))); +#endif /* * MUSB Register bits @@ -347,4 +353,14 @@ extern void musb_configure_ep(struct musb_epinfo *epinfo, u8 cnt); extern void write_fifo(u8 ep, u32 length, void *fifo_data); extern void read_fifo(u8 ep, u32 length, void *fifo_data); +#if defined(CONFIG_USB_BLACKFIN) +/* Every USB register is accessed as a 16-bit even if the value itself + * is only 8-bits in size. Fun stuff. + */ +# undef readb +# define readb(addr) (u8)bfin_read16(addr) +# undef writeb +# define writeb(b, addr) bfin_write16(addr, b) +#endif + #endif /* __MUSB_HDRC_DEFS_H__ */ diff --git a/drivers/usb/musb/musb_hcd.h b/drivers/usb/musb/musb_hcd.h index 17e9091..a437985 100644 --- a/drivers/usb/musb/musb_hcd.h +++ b/drivers/usb/musb/musb_hcd.h @@ -38,7 +38,9 @@ extern unsigned char new[]; #define MUSB_CONTROL_EP 0 /* This defines the endpoint number used for bulk transfer */ -#define MUSB_BULK_EP 1 +#ifndef MUSB_BULK_EP +# define MUSB_BULK_EP 1 +#endif /* This defines the endpoint number used for interrupt transfer */ #define MUSB_INTR_EP 2 diff --git a/include/asm-blackfin/mach-common/bits/usb.h b/include/asm-blackfin/mach-common/bits/usb.h new file mode 100644 index 0000000..c639058 --- /dev/null +++ b/include/asm-blackfin/mach-common/bits/usb.h @@ -0,0 +1,264 @@ +/* + * USB Masks + */ + +#ifndef __BFIN_PERIPHERAL_USB__ +#define __BFIN_PERIPHERAL_USB__ + +/* Bit masks for USB_FADDR */ + +#define FUNCTION_ADDRESS 0x7f /* Function address */ + +/* Bit masks for USB_POWER */ + +#define ENABLE_SUSPENDM 0x1 /* enable SuspendM output */ +#define SUSPEND_MODE 0x2 /* Suspend Mode indicator */ +#define RESUME_MODE 0x4 /* DMA Mode */ +#define RESET 0x8 /* Reset indicator */ +#define HS_MODE 0x10 /* High Speed mode indicator */ +#define HS_ENABLE 0x20 /* high Speed Enable */ +#define SOFT_CONN 0x40 /* Soft connect */ +#define ISO_UPDATE 0x80 /* Isochronous update */ + +/* Bit masks for USB_INTRTX */ + +#define EP0_TX 0x1 /* Tx Endpoint 0 interrupt */ +#define EP1_TX 0x2 /* Tx Endpoint 1 interrupt */ +#define EP2_TX 0x4 /* Tx Endpoint 2 interrupt */ +#define EP3_TX 0x8 /* Tx Endpoint 3 interrupt */ +#define EP4_TX 0x10 /* Tx Endpoint 4 interrupt */ +#define EP5_TX 0x20 /* Tx Endpoint 5 interrupt */ +#define EP6_TX 0x40 /* Tx Endpoint 6 interrupt */ +#define EP7_TX 0x80 /* Tx Endpoint 7 interrupt */ + +/* Bit masks for USB_INTRRX */ + +#define EP1_RX 0x2 /* Rx Endpoint 1 interrupt */ +#define EP2_RX 0x4 /* Rx Endpoint 2 interrupt */ +#define EP3_RX 0x8 /* Rx Endpoint 3 interrupt */ +#define EP4_RX 0x10 /* Rx Endpoint 4 interrupt */ +#define EP5_RX 0x20 /* Rx Endpoint 5 interrupt */ +#define EP6_RX 0x40 /* Rx Endpoint 6 interrupt */ +#define EP7_RX 0x80 /* Rx Endpoint 7 interrupt */ + +/* Bit masks for USB_INTRTXE */ + +#define EP0_TX_E 0x1 /* Endpoint 0 interrupt Enable */ +#define EP1_TX_E 0x2 /* Tx Endpoint 1 interrupt enable */ +#define EP2_TX_E 0x4 /* Tx Endpoint 2 interrupt enable */ +#define EP3_TX_E 0x8 /* Tx Endpoint 3 interrupt enable */ +#define EP4_TX_E 0x10 /* Tx Endpoint 4 interrupt enable */ +#define EP5_TX_E 0x20 /* Tx Endpoint 5 interrupt enable */ +#define EP6_TX_E 0x40 /* Tx Endpoint 6 interrupt enable */ +#define EP7_TX_E 0x80 /* Tx Endpoint 7 interrupt enable */ + +/* Bit masks for USB_INTRRXE */ + +#define EP1_RX_E 0x02 /* Rx Endpoint 1 interrupt enable */ +#define EP2_RX_E 0x04 /* Rx Endpoint 2 interrupt enable */ +#define EP3_RX_E 0x08 /* Rx Endpoint 3 interrupt enable */ +#define EP4_RX_E 0x10 /* Rx Endpoint 4 interrupt enable */ +#define EP5_RX_E 0x20 /* Rx Endpoint 5 interrupt enable */ +#define EP6_RX_E 0x40 /* Rx Endpoint 6 interrupt enable */ +#define EP7_RX_E 0x80 /* Rx Endpoint 7 interrupt enable */ + +/* Bit masks for USB_INTRUSB */ + +#define SUSPEND_B 0x01 /* Suspend indicator */ +#define RESUME_B 0x02 /* Resume indicator */ +#define RESET_OR_BABLE_B 0x04 /* Reset/babble indicator */ +#define SOF_B 0x08 /* Start of frame */ +#define CONN_B 0x10 /* Connection indicator */ +#define DISCON_B 0x20 /* Disconnect indicator */ +#define SESSION_REQ_B 0x40 /* Session Request */ +#define VBUS_ERROR_B 0x80 /* Vbus threshold indicator */ + +/* Bit masks for USB_INTRUSBE */ + +#define SUSPEND_BE 0x01 /* Suspend indicator int enable */ +#define RESUME_BE 0x02 /* Resume indicator int enable */ +#define RESET_OR_BABLE_BE 0x04 /* Reset/babble indicator int enable */ +#define SOF_BE 0x08 /* Start of frame int enable */ +#define CONN_BE 0x10 /* Connection indicator int enable */ +#define DISCON_BE 0x20 /* Disconnect indicator int enable */ +#define SESSION_REQ_BE 0x40 /* Session Request int enable */ +#define VBUS_ERROR_BE 0x80 /* Vbus threshold indicator int enable */ + +/* Bit masks for USB_FRAME */ + +#define FRAME_NUMBER 0x7ff /* Frame number */ + +/* Bit masks for USB_INDEX */ + +#define SELECTED_ENDPOINT 0xf /* selected endpoint */ + +/* Bit masks for USB_GLOBAL_CTL */ + +#define GLOBAL_ENA 0x0001 /* enables USB module */ +#define EP1_TX_ENA 0x0002 /* Transmit endpoint 1 enable */ +#define EP2_TX_ENA 0x0004 /* Transmit endpoint 2 enable */ +#define EP3_TX_ENA 0x0008 /* Transmit endpoint 3 enable */ +#define EP4_TX_ENA 0x0010 /* Transmit endpoint 4 enable */ +#define EP5_TX_ENA 0x0020 /* Transmit endpoint 5 enable */ +#define EP6_TX_ENA 0x0040 /* Transmit endpoint 6 enable */ +#define EP7_TX_ENA 0x0080 /* Transmit endpoint 7 enable */ +#define EP1_RX_ENA 0x0100 /* Receive endpoint 1 enable */ +#define EP2_RX_ENA 0x0200 /* Receive endpoint 2 enable */ +#define EP3_RX_ENA 0x0400 /* Receive endpoint 3 enable */ +#define EP4_RX_ENA 0x0800 /* Receive endpoint 4 enable */ +#define EP5_RX_ENA 0x1000 /* Receive endpoint 5 enable */ +#define EP6_RX_ENA 0x2000 /* Receive endpoint 6 enable */ +#define EP7_RX_ENA 0x4000 /* Receive endpoint 7 enable */ + +/* Bit masks for USB_OTG_DEV_CTL */ + +#define SESSION 0x1 /* session indicator */ +#define HOST_REQ 0x2 /* Host negotiation request */ +#define HOST_MODE 0x4 /* indicates USBDRC is a host */ +#define VBUS0 0x8 /* Vbus level indicator[0] */ +#define VBUS1 0x10 /* Vbus level indicator[1] */ +#define LSDEV 0x20 /* Low-speed indicator */ +#define FSDEV 0x40 /* Full or High-speed indicator */ +#define B_DEVICE 0x80 /* A' or 'B' device indicator */ + +/* Bit masks for USB_OTG_VBUS_IRQ */ + +#define DRIVE_VBUS_ON 0x1 /* indicator to drive VBUS control circuit */ +#define DRIVE_VBUS_OFF 0x2 /* indicator to shut off charge pump */ +#define CHRG_VBUS_START 0x4 /* indicator for external circuit to start charging VBUS */ +#define CHRG_VBUS_END 0x8 /* indicator for external circuit to end charging VBUS */ +#define DISCHRG_VBUS_START 0x10 /* indicator to start discharging VBUS */ +#define DISCHRG_VBUS_END 0x20 /* indicator to stop discharging VBUS */ + +/* Bit masks for USB_OTG_VBUS_MASK */ + +#define DRIVE_VBUS_ON_ENA 0x01 /* enable DRIVE_VBUS_ON interrupt */ +#define DRIVE_VBUS_OFF_ENA 0x02 /* enable DRIVE_VBUS_OFF interrupt */ +#define CHRG_VBUS_START_ENA 0x04 /* enable CHRG_VBUS_START interrupt */ +#define CHRG_VBUS_END_ENA 0x08 /* enable CHRG_VBUS_END interrupt */ +#define DISCHRG_VBUS_START_ENA 0x10 /* enable DISCHRG_VBUS_START interrupt */ +#define DISCHRG_VBUS_END_ENA 0x20 /* enable DISCHRG_VBUS_END interrupt */ + +/* Bit masks for USB_CSR0 */ + +#define RXPKTRDY 0x1 /* data packet receive indicator */ +#define TXPKTRDY 0x2 /* data packet in FIFO indicator */ +#define STALL_SENT 0x4 /* STALL handshake sent */ +#define DATAEND 0x8 /* Data end indicator */ +#define SETUPEND 0x10 /* Setup end */ +#define SENDSTALL 0x20 /* Send STALL handshake */ +#define SERVICED_RXPKTRDY 0x40 /* used to clear the RxPktRdy bit */ +#define SERVICED_SETUPEND 0x80 /* used to clear the SetupEnd bit */ +#define FLUSHFIFO 0x100 /* flush endpoint FIFO */ +#define STALL_RECEIVED_H 0x4 /* STALL handshake received host mode */ +#define SETUPPKT_H 0x8 /* send Setup token host mode */ +#define ERROR_H 0x10 /* timeout error indicator host mode */ +#define REQPKT_H 0x20 /* Request an IN transaction host mode */ +#define STATUSPKT_H 0x40 /* Status stage transaction host mode */ +#define NAK_TIMEOUT_H 0x80 /* EP0 halted after a NAK host mode */ + +/* Bit masks for USB_COUNT0 */ + +#define EP0_RX_COUNT 0x7f /* number of received bytes in EP0 FIFO */ + +/* Bit masks for USB_NAKLIMIT0 */ + +#define EP0_NAK_LIMIT 0x1f /* frames/micro frames count after which EP0 timeouts */ + +/* Bit masks for USB_TX_MAX_PACKET */ + +#define MAX_PACKET_SIZE_T 0x7ff /* maximum data pay load in a frame */ + +/* Bit masks for USB_RX_MAX_PACKET */ + +#define MAX_PACKET_SIZE_R 0x7ff /* maximum data pay load in a frame */ + +/* Bit masks for USB_TXCSR */ + +#define TXPKTRDY_T 0x1 /* data packet in FIFO indicator */ +#define FIFO_NOT_EMPTY_T 0x2 /* FIFO not empty */ +#define UNDERRUN_T 0x4 /* TxPktRdy not set for an IN token */ +#define FLUSHFIFO_T 0x8 /* flush endpoint FIFO */ +#define STALL_SEND_T 0x10 /* issue a Stall handshake */ +#define STALL_SENT_T 0x20 /* Stall handshake transmitted */ +#define CLEAR_DATATOGGLE_T 0x40 /* clear endpoint data toggle */ +#define INCOMPTX_T 0x80 /* indicates that a large packet is split */ +#define DMAREQMODE_T 0x400 /* DMA mode (0 or 1) selection */ +#define FORCE_DATATOGGLE_T 0x800 /* Force data toggle */ +#define DMAREQ_ENA_T 0x1000 /* Enable DMA request for Tx EP */ +#define ISO_T 0x4000 /* enable Isochronous transfers */ +#define AUTOSET_T 0x8000 /* allows TxPktRdy to be set automatically */ +#define ERROR_TH 0x4 /* error condition host mode */ +#define STALL_RECEIVED_TH 0x20 /* Stall handshake received host mode */ +#define NAK_TIMEOUT_TH 0x80 /* NAK timeout host mode */ + +/* Bit masks for USB_TXCOUNT */ + +#define TX_COUNT 0x1fff /* Byte len for the selected endpoint Tx FIFO */ + +/* Bit masks for USB_RXCSR */ + +#define RXPKTRDY_R 0x1 /* data packet in FIFO indicator */ +#define FIFO_FULL_R 0x2 /* FIFO not empty */ +#define OVERRUN_R 0x4 /* TxPktRdy not set for an IN token */ +#define DATAERROR_R 0x8 /* Out packet cannot be loaded into Rx FIFO */ +#define FLUSHFIFO_R 0x10 /* flush endpoint FIFO */ +#define STALL_SEND_R 0x20 /* issue a Stall handshake */ +#define STALL_SENT_R 0x40 /* Stall handshake transmitted */ +#define CLEAR_DATATOGGLE_R 0x80 /* clear endpoint data toggle */ +#define INCOMPRX_R 0x100 /* indicates that a large packet is split */ +#define DMAREQMODE_R 0x800 /* DMA mode (0 or 1) selection */ +#define DISNYET_R 0x1000 /* disable Nyet handshakes */ +#define DMAREQ_ENA_R 0x2000 /* Enable DMA request for Tx EP */ +#define ISO_R 0x4000 /* enable Isochronous transfers */ +#define AUTOCLEAR_R 0x8000 /* allows TxPktRdy to be set automatically */ +#define ERROR_RH 0x4 /* TxPktRdy not set for an IN token host mode */ +#define REQPKT_RH 0x20 /* request an IN transaction host mode */ +#define STALL_RECEIVED_RH 0x40 /* Stall handshake received host mode */ +#define INCOMPRX_RH 0x100 /* large packet is split host mode */ +#define DMAREQMODE_RH 0x800 /* DMA mode (0 or 1) selection host mode */ +#define AUTOREQ_RH 0x4000 /* sets ReqPkt automatically host mode */ + +/* Bit masks for USB_RXCOUNT */ + +#define RX_COUNT 0x1fff /* Packet byte len in the Rx FIFO */ + +/* Bit masks for USB_TXTYPE */ + +#define TARGET_EP_NO_T 0xf /* EP number */ +#define PROTOCOL_T 0xc /* transfer type */ + +/* Bit masks for USB_TXINTERVAL */ + +#define TX_POLL_INTERVAL 0xff /* polling interval for selected Tx EP */ + +/* Bit masks for USB_RXTYPE */ + +#define TARGET_EP_NO_R 0xf /* EP number */ +#define PROTOCOL_R 0xc /* transfer type */ + +/* Bit masks for USB_RXINTERVAL */ + +#define RX_POLL_INTERVAL 0xff /* polling interval for selected Rx EP */ + +/* Bit masks for USB_DMA_INTERRUPT */ + +#define DMA0_INT 0x1 /* DMA0 pending interrupt */ +#define DMA1_INT 0x2 /* DMA1 pending interrupt */ +#define DMA2_INT 0x4 /* DMA2 pending interrupt */ +#define DMA3_INT 0x8 /* DMA3 pending interrupt */ +#define DMA4_INT 0x10 /* DMA4 pending interrupt */ +#define DMA5_INT 0x20 /* DMA5 pending interrupt */ +#define DMA6_INT 0x40 /* DMA6 pending interrupt */ +#define DMA7_INT 0x80 /* DMA7 pending interrupt */ + +/* Bit masks for USB_DMAxCONTROL */ + +#define DMA_ENA 0x1 /* DMA enable */ +#define DIRECTION 0x2 /* direction of DMA transfer */ +#define MODE 0x4 /* DMA Bus error */ +#define INT_ENA 0x8 /* Interrupt enable */ +#define EPNUM 0xf0 /* EP number */ +#define BUSERROR 0x100 /* DMA Bus error */ + +#endif diff --git a/include/usb.h b/include/usb.h index 2a9cd04..a1f09d4 100644 --- a/include/usb.h +++ b/include/usb.h @@ -132,7 +132,8 @@ struct usb_device { defined(CONFIG_USB_EHCI) || defined(CONFIG_USB_OHCI_NEW) || \ defined(CONFIG_USB_SL811HS) || defined(CONFIG_USB_ISP116X_HCD) || \ defined(CONFIG_USB_R8A66597_HCD) || defined(CONFIG_USB_DAVINCI) || \ - defined(CONFIG_USB_OMAP3) || defined(CONFIG_USB_DA8XX) + defined(CONFIG_USB_OMAP3) || defined(CONFIG_USB_DA8XX) || \ + defined(CONFIG_USB_BLACKFIN) int usb_lowlevel_init(void); int usb_lowlevel_stop(void);