From: Michal Simek Date: Wed, 23 Feb 2022 14:45:42 +0000 (+0100) Subject: net: phy: Add support for ethernet-phy-id with gpio reset X-Git-Tag: v2022.07~124^2~15^2~5 X-Git-Url: http://review.tizen.org/git/?a=commitdiff_plain;h=a744a284e35420077b0c838598eb24c98710412a;p=platform%2Fkernel%2Fu-boot.git net: phy: Add support for ethernet-phy-id with gpio reset Ethernet phy like dp83867 is using strapping resistors to setup PHY address. On Xilinx boards strapping is setup on wires which are connected to SOC where internal pull ups/downs influnce phy address. That's why there is a need to setup pins properly (via pinctrl driver for example) and then perform phy reset. I can be workarounded by reset gpio done for mdio bus but this is not working properly when multiply phys sitting on the same bus. That's why it needs to be done via ethernet-phy-id driver where dt binding has gpio reset per phy. DT binding is available here: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/devicetree/bindings/net/ethernet-phy.yaml The driver is are reading the vendor and device id from valid phy node using ofnode_read_eth_phy_id() and creating a phy device. Kconfig PHY_ETHERNET_ID symbol is used because not every platform has gpio support. Signed-off-by: Michal Simek Signed-off-by: T Karthik Reddy Link: https://lore.kernel.org/r/70ab7d71c812b2c972d48c129e416c921af0d7f5.1645627539.git.michal.simek@xilinx.com --- diff --git a/MAINTAINERS b/MAINTAINERS index c58947f..4e740fb 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -617,6 +617,7 @@ F: drivers/i2c/muxes/pca954x.c F: drivers/i2c/zynq_i2c.c F: drivers/mmc/zynq_sdhci.c F: drivers/mtd/nand/raw/zynq_nand.c +F: drivers/net/phy/ethernet_id.c F: drivers/net/phy/xilinx_phy.c F: drivers/net/zynq_gem.c F: drivers/serial/serial_zynq.c diff --git a/drivers/net/phy/Kconfig b/drivers/net/phy/Kconfig index 4f8d33c..74339a2 100644 --- a/drivers/net/phy/Kconfig +++ b/drivers/net/phy/Kconfig @@ -307,6 +307,14 @@ config PHY_XILINX_GMII2RGMII as bridge between MAC connected over GMII and external phy that is connected over RGMII interface. +config PHY_ETHERNET_ID + bool "Read ethernet PHY id" + depends on DM_GPIO + default y if ZYNQ_GEM + help + Enable this config to read ethernet phy id from the phy node of DT + and create a phy device using id. + config PHY_FIXED bool "Fixed-Link PHY" depends on DM_ETH diff --git a/drivers/net/phy/Makefile b/drivers/net/phy/Makefile index 77f7f60..b28440b 100644 --- a/drivers/net/phy/Makefile +++ b/drivers/net/phy/Makefile @@ -32,6 +32,7 @@ obj-$(CONFIG_PHY_TI_DP83867) += dp83867.o obj-$(CONFIG_PHY_TI_DP83869) += dp83869.o obj-$(CONFIG_PHY_XILINX) += xilinx_phy.o obj-$(CONFIG_PHY_XILINX_GMII2RGMII) += xilinx_gmii2rgmii.o +obj-$(CONFIG_PHY_ETHERNET_ID) += ethernet_id.o obj-$(CONFIG_PHY_VITESSE) += vitesse.o obj-$(CONFIG_PHY_MSCC) += mscc.o obj-$(CONFIG_PHY_FIXED) += fixed.o diff --git a/drivers/net/phy/ethernet_id.c b/drivers/net/phy/ethernet_id.c new file mode 100644 index 0000000..5617ac3 --- /dev/null +++ b/drivers/net/phy/ethernet_id.c @@ -0,0 +1,69 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Xilinx ethernet phy reset driver + * + * Copyright (C) 2022 Xilinx, Inc. + */ + +#include +#include +#include +#include +#include + +struct phy_device *phy_connect_phy_id(struct mii_dev *bus, struct udevice *dev, + phy_interface_t interface) +{ + struct phy_device *phydev; + struct ofnode_phandle_args phandle_args; + struct gpio_desc gpio; + ofnode node; + u32 id, assert, deassert; + u16 vendor, device; + int ret; + + if (dev_read_phandle_with_args(dev, "phy-handle", NULL, 0, 0, + &phandle_args)) + return NULL; + + if (!ofnode_valid(phandle_args.node)) + return NULL; + + node = phandle_args.node; + + ret = ofnode_read_eth_phy_id(node, &vendor, &device); + if (ret) { + dev_err(dev, "Failed to read eth PHY id, err: %d\n", ret); + return NULL; + } + + ret = gpio_request_by_name_nodev(node, "reset-gpios", 0, &gpio, + GPIOD_ACTIVE_LOW); + if (!ret) { + assert = ofnode_read_u32_default(node, "reset-assert-us", 0); + deassert = ofnode_read_u32_default(node, + "reset-deassert-us", 0); + ret = dm_gpio_set_value(&gpio, 1); + if (ret) { + dev_err(dev, "Failed assert gpio, err: %d\n", ret); + return NULL; + } + + udelay(assert); + + ret = dm_gpio_set_value(&gpio, 0); + if (ret) { + dev_err(dev, "Failed deassert gpio, err: %d\n", ret); + return NULL; + } + + udelay(deassert); + } + + id = vendor << 16 | device; + phydev = phy_device_create(bus, 0, id, false, interface); + if (phydev) + phydev->node = node; + + return phydev; +} diff --git a/drivers/net/phy/phy.c b/drivers/net/phy/phy.c index f63705e..fffa10f 100644 --- a/drivers/net/phy/phy.c +++ b/drivers/net/phy/phy.c @@ -1047,6 +1047,11 @@ struct phy_device *phy_connect(struct mii_dev *bus, int addr, phydev = phy_device_create(bus, 0, PHY_NCSI_ID, false, interface); #endif +#ifdef CONFIG_PHY_ETHERNET_ID + if (!phydev) + phydev = phy_connect_phy_id(bus, dev, interface); +#endif + #ifdef CONFIG_PHY_XILINX_GMII2RGMII if (!phydev) phydev = phy_connect_gmii2rgmii(bus, dev, interface); diff --git a/include/phy.h b/include/phy.h index 832d7a1..9ea4bd4 100644 --- a/include/phy.h +++ b/include/phy.h @@ -468,6 +468,19 @@ struct phy_device *phy_device_create(struct mii_dev *bus, int addr, u32 phy_id, bool is_c45, phy_interface_t interface); +/** + * phy_connect_phy_id() - Connect to phy device by reading PHY id + * from phy node. + * + * @bus: MII/MDIO bus that hosts the PHY + * @dev: Ethernet device to associate to the PHY + * @interface: Interface between the MAC and PHY + * @return: pointer to phy_device if a PHY is found, + * or NULL otherwise + */ +struct phy_device *phy_connect_phy_id(struct mii_dev *bus, struct udevice *dev, + phy_interface_t interface); + static inline ofnode phy_get_ofnode(struct phy_device *phydev) { if (ofnode_valid(phydev->node))