From: Douglas Anderson Date: Fri, 20 Oct 2023 21:06:52 +0000 (-0700) Subject: r8152: Increase USB control msg timeout to 5000ms as per spec X-Git-Tag: v6.6.17~3692^2~13^2~7 X-Git-Url: http://review.tizen.org/git/?a=commitdiff_plain;h=a5feba71ec9c14a54c3babdc732c5b6866d8ee43;p=platform%2Fkernel%2Flinux-rpi.git r8152: Increase USB control msg timeout to 5000ms as per spec According to the comment next to USB_CTRL_GET_TIMEOUT and USB_CTRL_SET_TIMEOUT, although sending/receiving control messages is usually quite fast, the spec allows them to take up to 5 seconds. Let's increase the timeout in the Realtek driver from 500ms to 5000ms (using the #defines) to account for this. This is not just a theoretical change. The need for the longer timeout was seen in testing. Specifically, if you drop a sc7180-trogdor based Chromebook into the kdb debugger and then "go" again after sitting in the debugger for a while, the next USB control message takes a long time. Out of ~40 tests the slowest USB control message was 4.5 seconds. While dropping into kdb is not exactly an end-user scenario, the above is similar to what could happen due to an temporary interrupt storm, what could happen if there was a host controller (HW or SW) issue, or what could happen if the Realtek device got into a confused state and needed time to recover. This change is fairly critical since the r8152 driver in Linux doesn't expect register reads/writes (which are backed by USB control messages) to fail. Fixes: ac718b69301c ("net/usb: new driver for RTL8152") Suggested-by: Hayes Wang Signed-off-by: Douglas Anderson Reviewed-by: Grant Grundler Signed-off-by: David S. Miller --- diff --git a/drivers/net/usb/r8152.c b/drivers/net/usb/r8152.c index 0c13d99..482957b 100644 --- a/drivers/net/usb/r8152.c +++ b/drivers/net/usb/r8152.c @@ -1212,7 +1212,7 @@ int get_registers(struct r8152 *tp, u16 value, u16 index, u16 size, void *data) ret = usb_control_msg(tp->udev, tp->pipe_ctrl_in, RTL8152_REQ_GET_REGS, RTL8152_REQT_READ, - value, index, tmp, size, 500); + value, index, tmp, size, USB_CTRL_GET_TIMEOUT); if (ret < 0) memset(data, 0xff, size); else @@ -1235,7 +1235,7 @@ int set_registers(struct r8152 *tp, u16 value, u16 index, u16 size, void *data) ret = usb_control_msg(tp->udev, tp->pipe_ctrl_out, RTL8152_REQ_SET_REGS, RTL8152_REQT_WRITE, - value, index, tmp, size, 500); + value, index, tmp, size, USB_CTRL_SET_TIMEOUT); kfree(tmp); @@ -9494,7 +9494,8 @@ static u8 __rtl_get_hw_ver(struct usb_device *udev) ret = usb_control_msg(udev, usb_rcvctrlpipe(udev, 0), RTL8152_REQ_GET_REGS, RTL8152_REQT_READ, - PLA_TCR0, MCU_TYPE_PLA, tmp, sizeof(*tmp), 500); + PLA_TCR0, MCU_TYPE_PLA, tmp, sizeof(*tmp), + USB_CTRL_GET_TIMEOUT); if (ret > 0) ocp_data = (__le32_to_cpu(*tmp) >> 16) & VERSION_MASK;