From: Russell King <rmk+kernel@armlinux.org.uk>
Date: Sun, 2 Sep 2018 16:29:12 +0000 (+0200)
Subject: ARM: dts: vf610-zii-dev-rev-c: add support for one SFF module
X-Git-Tag: v5.15~7693^2~18^2~24
X-Git-Url: http://review.tizen.org/git/?a=commitdiff_plain;h=9dfc1600894fafb4ff0304b801c1744f28e2f272;p=platform%2Fkernel%2Flinux-starfive.git

ARM: dts: vf610-zii-dev-rev-c: add support for one SFF module

The board typically has 2 populated SFF interfaces. The mv88e6xxx
driver currently supports SFF modules connected to ports 9 and 10 of
the mv88e6390. Add support for sff2, which is connected to port 9.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
---

diff --git a/arch/arm/boot/dts/vf610-zii-dev-rev-c.dts b/arch/arm/boot/dts/vf610-zii-dev-rev-c.dts
index 0b1e94c..6f4a560 100644
--- a/arch/arm/boot/dts/vf610-zii-dev-rev-c.dts
+++ b/arch/arm/boot/dts/vf610-zii-dev-rev-c.dts
@@ -200,6 +200,13 @@
 						phy-handle = <&switch1phy4>;
 					};
 
+					port@9 {
+						reg = <9>;
+						label = "sff2";
+						phy-mode = "sgmii";
+						managed = "in-band-status";
+						sfp = <&sff2>;
+					};
 
 					switch1port10: port@10 {
 						reg = <10>;
@@ -245,6 +252,22 @@
 			#size-cells = <0>;
 		};
 	};
+
+	sff2: sff2 {
+		/* lower */
+		compatible = "sff,sff";
+		i2c-bus = <&sff2_i2c>;
+		los-gpios = <&gpio6 12 GPIO_ACTIVE_HIGH>;
+		tx-disable-gpios = <&gpio6 14 GPIO_ACTIVE_HIGH>;
+	};
+
+	sff3: sff3 {
+		/* upper */
+		compatible = "sff,sff";
+		i2c-bus = <&sff3_i2c>;
+		los-gpios = <&gpio6 13 GPIO_ACTIVE_HIGH>;
+		tx-disable-gpios = <&gpio6 15 GPIO_ACTIVE_HIGH>;
+	};
 };
 
 &dspi0 {
@@ -329,13 +352,6 @@
 		interrupts = <23 IRQ_TYPE_EDGE_FALLING>;
 		gpio-controller;
 		interrupt-controller;
-
-		enet_swr_en {
-			gpio-hog;
-			gpios = <0 GPIO_ACTIVE_HIGH>;
-			output-high;
-			line-name = "enet-swr-en";
-		};
 	};
 
 	/*
@@ -378,26 +394,16 @@
 			reg = <0>;
 		};
 
-		i2c@1 {
+		sff2_i2c: i2c@1 {
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <1>;
-
-			sfp2: at24c04@50 {
-				compatible = "atmel,24c02";
-				reg = <0x50>;
-			};
 		};
 
-		i2c@2 {
+		sff3_i2c: i2c@2 {
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <2>;
-
-			sfp3: at24c04@50 {
-				compatible = "atmel,24c02";
-				reg = <0x50>;
-			};
 		};
 
 		i2c@3 {