From: Matthew McClintock Date: Mon, 13 Aug 2012 08:10:37 +0000 (+0000) Subject: p1014rdb: set ddr bus width properly depending on SVR X-Git-Tag: v2012.10-rc2~67^2~35 X-Git-Url: http://review.tizen.org/git/?a=commitdiff_plain;h=9c6b47d53ed329b31c5f26e9ec710f67559c07f0;p=kernel%2Fu-boot.git p1014rdb: set ddr bus width properly depending on SVR Currently, for NAND boot for the P1010/4RDB we hard code the DDR configuration. We can still dynamically set the DDR bus width in the nand spl so the P1010/4RDB boards can boot from the same u-boot image Signed-off-by: Matthew McClintock Signed-off-by: Andy Fleming --- diff --git a/arch/powerpc/include/asm/fsl_ddr_sdram.h b/arch/powerpc/include/asm/fsl_ddr_sdram.h index 93639ba..157ae24 100644 --- a/arch/powerpc/include/asm/fsl_ddr_sdram.h +++ b/arch/powerpc/include/asm/fsl_ddr_sdram.h @@ -88,6 +88,7 @@ typedef ddr3_spd_eeprom_t generic_spd_eeprom_t; #define SDRAM_CFG_SDRAM_TYPE_MASK 0x07000000 #define SDRAM_CFG_SDRAM_TYPE_SHIFT 24 #define SDRAM_CFG_DYN_PWR 0x00200000 +#define SDRAM_CFG_DBW_MASK 0x00180000 #define SDRAM_CFG_32_BE 0x00080000 #define SDRAM_CFG_16_BE 0x00100000 #define SDRAM_CFG_8_BE 0x00040000 diff --git a/nand_spl/board/freescale/p1010rdb/nand_boot.c b/nand_spl/board/freescale/p1010rdb/nand_boot.c index 16eeb61..1f89ab5 100644 --- a/nand_spl/board/freescale/p1010rdb/nand_boot.c +++ b/nand_spl/board/freescale/p1010rdb/nand_boot.c @@ -35,6 +35,7 @@ unsigned long ddr_freq_mhz; void sdram_init(void) { ccsr_ddr_t *ddr = (ccsr_ddr_t *)CONFIG_SYS_MPC85xx_DDR_ADDR; + u32 svr = mfspr(SPRN_SVR); out_be32(&ddr->sdram_cfg, CONFIG_SYS_DDR_CONTROL | SDRAM_CFG_32_BE); out_be32(&ddr->cs0_bnds, CONFIG_SYS_DDR_CS0_BNDS); @@ -70,6 +71,16 @@ void sdram_init(void) out_be32(&ddr->timing_cfg_5, CONFIG_SYS_DDR_TIMING_5); out_be32(&ddr->ddr_zq_cntl, CONFIG_SYS_DDR_ZQ_CONTROL); + /* P1014 and it's derivatives support max 16bit DDR width */ + if (svr == SVR_P1014) { + __raw_writel(ddr->sdram_cfg & ~SDRAM_CFG_DBW_MASK, &ddr->sdram_cfg); + __raw_writel(ddr->sdram_cfg | SDRAM_CFG_16_BE, &ddr->sdram_cfg); + /* For CS0_BNDS we divide the start and end address by 2, so we can just + * shift the entire register to achieve the desired result and the mask + * the value so we don't write reserved fields */ + __raw_writel((CONFIG_SYS_DDR_CS0_BNDS >> 1) & 0x0fff0fff, &ddr->cs0_bnds); + } + /* mimic 500us delay, with busy isync() loop */ udelay(100);