From: Mike Turquette <mturquette@linaro.org>
Date: Mon, 26 Mar 2012 18:51:34 +0000 (-0700)
Subject: clk: core: correct clk_set_rate kerneldoc
X-Git-Tag: v3.5-rc1~71^2~6^2~29
X-Git-Url: http://review.tizen.org/git/?a=commitdiff_plain;h=5654dc94f872f823aa13941a8fdba69a3feca39c;p=profile%2Fivi%2Fkernel-x86-ivi.git

clk: core: correct clk_set_rate kerneldoc

Remove old and misleading documentation from the previous clk_set_rate
implementaion.

Reported-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
---

diff --git a/drivers/clk/clk.c b/drivers/clk/clk.c
index 9cf6f59e..3ed36d3 100644
--- a/drivers/clk/clk.c
+++ b/drivers/clk/clk.c
@@ -859,38 +859,19 @@ static void clk_change_rate(struct clk *clk)
  * @clk: the clk whose rate is being changed
  * @rate: the new rate for clk
  *
- * In the simplest case clk_set_rate will only change the rate of clk.
+ * In the simplest case clk_set_rate will only adjust the rate of clk.
  *
- * If clk has the CLK_SET_RATE_GATE flag set and it is enabled this call
- * will fail; only when the clk is disabled will it be able to change
- * its rate.
+ * Setting the CLK_SET_RATE_PARENT flag allows the rate change operation to
+ * propagate up to clk's parent; whether or not this happens depends on the
+ * outcome of clk's .round_rate implementation.  If *parent_rate is unchanged
+ * after calling .round_rate then upstream parent propagation is ignored.  If
+ * *parent_rate comes back with a new rate for clk's parent then we propagate
+ * up to clk's parent and set it's rate.  Upward propagation will continue
+ * until either a clk does not support the CLK_SET_RATE_PARENT flag or
+ * .round_rate stops requesting changes to clk's parent_rate.
  *
- * Setting the CLK_SET_RATE_PARENT flag allows clk_set_rate to
- * recursively propagate up to clk's parent; whether or not this happens
- * depends on the outcome of clk's .round_rate implementation.  If
- * *parent_rate is 0 after calling .round_rate then upstream parent
- * propagation is ignored.  If *parent_rate comes back with a new rate
- * for clk's parent then we propagate up to clk's parent and set it's
- * rate.  Upward propagation will continue until either a clk does not
- * support the CLK_SET_RATE_PARENT flag or .round_rate stops requesting
- * changes to clk's parent_rate.  If there is a failure during upstream
- * propagation then clk_set_rate will unwind and restore each clk's rate
- * that had been successfully changed.  Afterwards a rate change abort
- * notification will be propagated downstream, starting from the clk
- * that failed.
- *
- * At the end of all of the rate setting, clk_set_rate internally calls
- * __clk_recalc_rates and propagates the rate changes downstream,
- * starting from the highest clk whose rate was changed.  This has the
- * added benefit of propagating post-rate change notifiers.
- *
- * Note that while post-rate change and rate change abort notifications
- * are guaranteed to be sent to a clk only once per call to
- * clk_set_rate, pre-change notifications will be sent for every clk
- * whose rate is changed.  Stacking pre-change notifications is noisy
- * for the drivers subscribed to them, but this allows drivers to react
- * to intermediate clk rate changes up until the point where the final
- * rate is achieved at the end of upstream propagation.
+ * Rate changes are accomplished via tree traversal that also recalculates the
+ * rates for the clocks and fires off POST_RATE_CHANGE notifiers.
  *
  * Returns 0 on success, -EERROR otherwise.
  */