From: Michal Simek Date: Wed, 9 Dec 2015 11:50:05 +0000 (+0100) Subject: serial: uartlite: Add uartlite to Kconfig X-Git-Tag: v2016.03-rc1~46^2~90 X-Git-Url: http://review.tizen.org/git/?a=commitdiff_plain;h=54e24d33324a1a4599d9f830a8671a61c45300fc;p=platform%2Fkernel%2Fu-boot.git serial: uartlite: Add uartlite to Kconfig - Move config option out of board file. - Remove uartlite address from config file Signed-off-by: Michal Simek Reviewed-by: Thomas Chou --- diff --git a/board/xilinx/microblaze-generic/xparameters.h b/board/xilinx/microblaze-generic/xparameters.h index 8ba146c..11b3c9a 100644 --- a/board/xilinx/microblaze-generic/xparameters.h +++ b/board/xilinx/microblaze-generic/xparameters.h @@ -28,10 +28,6 @@ #define XILINX_TIMER_BASEADDR 0x41c00000 #define XILINX_TIMER_IRQ 0 -/* Uart pheriphery is RS232_Uart */ -#define XILINX_UARTLITE_BASEADDR 0x40600000 -#define XILINX_UARTLITE_BAUDRATE 115200 - /* IIC pheriphery is IIC_EEPROM */ #define XILINX_IIC_0_BASEADDR 0x40800000 #define XILINX_IIC_0_FREQ 100000 diff --git a/configs/microblaze-generic_defconfig b/configs/microblaze-generic_defconfig index 6b038b8..dc4ac05 100644 --- a/configs/microblaze-generic_defconfig +++ b/configs/microblaze-generic_defconfig @@ -10,3 +10,4 @@ CONFIG_CMD_GPIO=y # CONFIG_CMD_SETEXPR is not set CONFIG_SPL_OF_CONTROL=y CONFIG_OF_EMBED=y +CONFIG_XILINX_UARTLITE=y diff --git a/drivers/serial/Kconfig b/drivers/serial/Kconfig index e78c5d3..5c7b1fa 100644 --- a/drivers/serial/Kconfig +++ b/drivers/serial/Kconfig @@ -278,4 +278,11 @@ config UNIPHIER_SERIAL If you have a UniPhier based board and want to use the on-chip serial ports, say Y to this option. If unsure, say N. +config XILINX_UARTLITE + bool "Xilinx Uarlite support" + depends on DM_SERIAL && (MICROBLAZE || ARCH_ZYNQ || ARCH_ZYNQMP) + help + If you have a Xilinx based board and want to use the uartlite + serial ports, say Y to this option. If unsure, say N. + endmenu diff --git a/include/configs/microblaze-generic.h b/include/configs/microblaze-generic.h index 10ac832..6e3c80b 100644 --- a/include/configs/microblaze-generic.h +++ b/include/configs/microblaze-generic.h @@ -37,10 +37,7 @@ # define CONFIG_SYS_BAUDRATE_TABLE \ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400} -#ifdef XILINX_UARTLITE_BASEADDR -# define CONFIG_XILINX_UARTLITE -# define CONFIG_SERIAL_BASE XILINX_UARTLITE_BASEADDR -#elif XILINX_UART16550_BASEADDR +#if XILINX_UART16550_BASEADDR # define CONFIG_SYS_NS16550_SERIAL # if defined(__MICROBLAZEEL__) # define CONFIG_SYS_NS16550_REG_SIZE -4 @@ -51,8 +48,6 @@ # define CONFIG_SYS_NS16550_COM1 \ ((XILINX_UART16550_BASEADDR & ~0xF) + 0x1000) # define CONFIG_SYS_NS16550_CLK XILINX_UART16550_CLOCK_HZ -#else -# error Undefined uart #endif /* setting reset address */