From: Marek Szyprowski <m.szyprowski@samsung.com>
Date: Mon, 7 Oct 2024 09:15:26 +0000 (+0200)
Subject: tizen: bootscript: remove outdated/obsolete/unused RPi3 boot script
X-Git-Tag: accepted/tizen/unified/20241101.174134~8
X-Git-Url: http://review.tizen.org/git/?a=commitdiff_plain;h=45a7c68424cb1d6367827669fc88790f8ecfefcf;p=platform%2Fkernel%2Fu-boot.git

tizen: bootscript: remove outdated/obsolete/unused RPi3 boot script

To avoid confusion, remove unused files. If needed, it can be restored
from older Tizen releases.

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Change-Id: I33729a7451cf0c423521fbbc340714cc5510239a
---

diff --git a/tizen/bootscript/tizen-boot-rpi3.scr b/tizen/bootscript/tizen-boot-rpi3.scr
deleted file mode 100644
index 0cbe8a8a83..0000000000
--- a/tizen/bootscript/tizen-boot-rpi3.scr
+++ /dev/null
@@ -1,91 +0,0 @@
-# U-boot script for tizen RPI3
-
-if test "${target}" = "mmc0"; then;
-	setenv bootdev mmc
-fi
-if test "${target}" = "usb0"; then;
-	setenv bootdev usb
-fi
-
-if test -e $bootdev $mmcbootdev:$mmcinformpart $rebootparamfile; then;
-	ext4load $bootdev $mmcbootdev:$mmcinformpart $rebootparam_addr $rebootparamfile;
-	if itest.l *${rebootparam_addr} == ${upgrade_val}; then;
-		setenv ramdiskpart 8
-		setenv bootmode fota
-	elif itest.l *${rebootparam_addr} == ${recovery_val}; then;
-		setenv ramdiskpart 8
-		setenv bootmode recovery
-	elif itest.l *${rebootparam_addr} == ${download_val}; then;
-		setenv ramdiskpart 8
-		setenv bootmode flash
-	elif itest.l *${rebootparam_addr} == ${nodef_val}; then;
-		echo "This reboot parameter is not supported...";
-	fi
-fi
-
-# This is for jumping to flash mode on u-boot.
-if test "${bootmode}" = "download"; then;
-	setenv ramdiskpart 8
-	setenv bootmode flash
-fi
-
-if test "${bootmode}" = "flash"; then;
-	if test -n "${ipaddr}"; then;
-		ip_opt=\"ip=${ipaddr}::${gateway}:${netmask}\"
-	fi
-fi
-
-# boot from ram0 if there is sbin
-if test -e $bootdev $mmcrootdev:$ramdiskpart sbin/init; then;
-	setenv rootdev ram0
-else
-	if test "${bootdev}" = "mmc"; then;
-		setenv rootdev mmcblk${mmcrootdev}p${mmcrootpart}
-	fi
-	if test "${bootdev}" = "usb"; then;
-		setenv rootdev sda${mmcrootpart}
-	fi
-	setenv bootmode normal
-fi
-
-# setting console device if noting is set
-if test -z "${console}"; then;
-	setenv console "console=ttyS0,115200n8 earlycon=uart8250,mmio32,0x3f215040"
-fi
-echo "console: ${console}"
-
-# DT image by model
-if itest.l ${board_rev} == 0xd; then;
-	setenv fdtfile \"bcm2710-rpi-3-b-plus.dtb\"
-else
-	setenv fdtfile \"bcm2710-rpi-3-b.dtb\"
-fi
-setenv boot_prefixes \"/\"
-
-# To use cmdline for using serial console. /* Normal mode */
-setenv bootargs \"${tizen_bootarg} smsc95xx.macaddr=${ethaddr} root=/dev/${rootdev} rw bootmode=${bootmode} rootwait ${console} ${opts} ${ip_opt}\"
-
-# Find the ramdisk offset and block count
-part start $bootdev $mmcrootdev $ramdiskpart ramdisk_start
-part size $bootdev $mmcrootdev $ramdiskpart ramdisk_size
-
-# Set to ramdisksize with real partition size. (Need to multiply block-size 0x200)
-setexpr ramdisksize $ramdisk_size * 200
-setexpr tizen_kernel_addr_r $ramdisk_addr_r + $ramdisksize
-
-echo "Searching for kernel in"; for prefix in $boot_prefixes; do
-if load $bootdev $mmcbootdev:$mmcbootpart $tizen_kernel_addr_r $prefix$kernel; then;
-	echo ${bootmode} "boot";
-	load $bootdev $mmcbootdev:$mmcbootpart $fdt_addr $fdtfile;
-	if test -e $bootdev $mmcrootdev:$ramdiskpart sbin/init; then;
-		echo "Loading Ramdisk from partition"${ramdiskpart};
-		$bootdev read $ramdisk_addr_r $ramdisk_start $ramdisk_size;
-	fi
-
-	if test "$kernel" = "zImage"; then;
-		bootz $tizen_kernel_addr_r $ramdisk_addr_r:$ramdisksize $fdt_addr;
-	else
-		booti $tizen_kernel_addr_r $ramdisk_addr_r:$ramdisksize $fdt_addr;
-	fi
-fi
-done