From: Luiz Angelo Daros de Luca Date: Wed, 9 Feb 2022 18:41:16 +0000 (-0300) Subject: dt-bindings: net: dsa: realtek: convert to YAML schema, add MDIO X-Git-Tag: v6.1-rc5~1746^2~379 X-Git-Url: http://review.tizen.org/git/?a=commitdiff_plain;h=429c83c78ab213d9656721cf46ae05366098485c;p=platform%2Fkernel%2Flinux-starfive.git dt-bindings: net: dsa: realtek: convert to YAML schema, add MDIO Schema changes: - support for mdio-connected switches (mdio driver), recognized by checking the presence of property "reg" - new compatible strings for rtl8367s and rtl8367rb - "interrupt-controller" was not added as a required property. It might still work polling the ports when missing. Examples changes: - renamed "switch_intc" to make it unique between examples - removed "dsa-mdio" from mdio compatible property - renamed phy@0 to ethernet-phy@0 (not tested with real HW) phy@ requires #phy-cells Signed-off-by: Luiz Angelo Daros de Luca Reviewed-by: Linus Walleij Signed-off-by: David S. Miller --- diff --git a/Documentation/devicetree/bindings/net/dsa/realtek-smi.txt b/Documentation/devicetree/bindings/net/dsa/realtek-smi.txt deleted file mode 100644 index 7959ec2..0000000 --- a/Documentation/devicetree/bindings/net/dsa/realtek-smi.txt +++ /dev/null @@ -1,240 +0,0 @@ -Realtek SMI-based Switches -========================== - -The SMI "Simple Management Interface" is a two-wire protocol using -bit-banged GPIO that while it reuses the MDIO lines MCK and MDIO does -not use the MDIO protocol. This binding defines how to specify the -SMI-based Realtek devices. - -Required properties: - -- compatible: must be exactly one of: - "realtek,rtl8365mb" (4+1 ports) - "realtek,rtl8366" - "realtek,rtl8366rb" (4+1 ports) - "realtek,rtl8366s" (4+1 ports) - "realtek,rtl8367" - "realtek,rtl8367b" - "realtek,rtl8368s" (8 port) - "realtek,rtl8369" - "realtek,rtl8370" (8 port) - -Required properties: -- mdc-gpios: GPIO line for the MDC clock line. -- mdio-gpios: GPIO line for the MDIO data line. -- reset-gpios: GPIO line for the reset signal. - -Optional properties: -- realtek,disable-leds: if the LED drivers are not used in the - hardware design this will disable them so they are not turned on - and wasting power. - -Required subnodes: - -- interrupt-controller - - This defines an interrupt controller with an IRQ line (typically - a GPIO) that will demultiplex and handle the interrupt from the single - interrupt line coming out of one of the SMI-based chips. It most - importantly provides link up/down interrupts to the PHY blocks inside - the ASIC. - -Required properties of interrupt-controller: - -- interrupt: parent interrupt, see interrupt-controller/interrupts.txt -- interrupt-controller: see interrupt-controller/interrupts.txt -- #address-cells: should be <0> -- #interrupt-cells: should be <1> - -- mdio - - This defines the internal MDIO bus of the SMI device, mostly for the - purpose of being able to hook the interrupts to the right PHY and - the right PHY to the corresponding port. - -Required properties of mdio: - -- compatible: should be set to "realtek,smi-mdio" for all SMI devices - -See net/mdio.txt for additional MDIO bus properties. - -See net/dsa/dsa.txt for a list of additional required and optional properties -and subnodes of DSA switches. - -Examples: - -An example for the RTL8366RB: - -switch { - compatible = "realtek,rtl8366rb"; - /* 22 = MDIO (has input reads), 21 = MDC (clock, output only) */ - mdc-gpios = <&gpio0 21 GPIO_ACTIVE_HIGH>; - mdio-gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>; - reset-gpios = <&gpio0 14 GPIO_ACTIVE_LOW>; - - switch_intc: interrupt-controller { - /* GPIO 15 provides the interrupt */ - interrupt-parent = <&gpio0>; - interrupts = <15 IRQ_TYPE_LEVEL_LOW>; - interrupt-controller; - #address-cells = <0>; - #interrupt-cells = <1>; - }; - - ports { - #address-cells = <1>; - #size-cells = <0>; - reg = <0>; - port@0 { - reg = <0>; - label = "lan0"; - phy-handle = <&phy0>; - }; - port@1 { - reg = <1>; - label = "lan1"; - phy-handle = <&phy1>; - }; - port@2 { - reg = <2>; - label = "lan2"; - phy-handle = <&phy2>; - }; - port@3 { - reg = <3>; - label = "lan3"; - phy-handle = <&phy3>; - }; - port@4 { - reg = <4>; - label = "wan"; - phy-handle = <&phy4>; - }; - port@5 { - reg = <5>; - label = "cpu"; - ethernet = <&gmac0>; - phy-mode = "rgmii"; - fixed-link { - speed = <1000>; - full-duplex; - }; - }; - }; - - mdio { - compatible = "realtek,smi-mdio", "dsa-mdio"; - #address-cells = <1>; - #size-cells = <0>; - - phy0: phy@0 { - reg = <0>; - interrupt-parent = <&switch_intc>; - interrupts = <0>; - }; - phy1: phy@1 { - reg = <1>; - interrupt-parent = <&switch_intc>; - interrupts = <1>; - }; - phy2: phy@2 { - reg = <2>; - interrupt-parent = <&switch_intc>; - interrupts = <2>; - }; - phy3: phy@3 { - reg = <3>; - interrupt-parent = <&switch_intc>; - interrupts = <3>; - }; - phy4: phy@4 { - reg = <4>; - interrupt-parent = <&switch_intc>; - interrupts = <12>; - }; - }; -}; - -An example for the RTL8365MB-VC: - -switch { - compatible = "realtek,rtl8365mb"; - mdc-gpios = <&gpio1 16 GPIO_ACTIVE_HIGH>; - mdio-gpios = <&gpio1 17 GPIO_ACTIVE_HIGH>; - reset-gpios = <&gpio5 0 GPIO_ACTIVE_LOW>; - - switch_intc: interrupt-controller { - interrupt-parent = <&gpio5>; - interrupts = <1 IRQ_TYPE_LEVEL_LOW>; - interrupt-controller; - #address-cells = <0>; - #interrupt-cells = <1>; - }; - - ports { - #address-cells = <1>; - #size-cells = <0>; - reg = <0>; - port@0 { - reg = <0>; - label = "swp0"; - phy-handle = <ðphy0>; - }; - port@1 { - reg = <1>; - label = "swp1"; - phy-handle = <ðphy1>; - }; - port@2 { - reg = <2>; - label = "swp2"; - phy-handle = <ðphy2>; - }; - port@3 { - reg = <3>; - label = "swp3"; - phy-handle = <ðphy3>; - }; - port@6 { - reg = <6>; - label = "cpu"; - ethernet = <&fec1>; - phy-mode = "rgmii"; - tx-internal-delay-ps = <2000>; - rx-internal-delay-ps = <2000>; - - fixed-link { - speed = <1000>; - full-duplex; - pause; - }; - }; - }; - - mdio { - compatible = "realtek,smi-mdio"; - #address-cells = <1>; - #size-cells = <0>; - - ethphy0: phy@0 { - reg = <0>; - interrupt-parent = <&switch_intc>; - interrupts = <0>; - }; - ethphy1: phy@1 { - reg = <1>; - interrupt-parent = <&switch_intc>; - interrupts = <1>; - }; - ethphy2: phy@2 { - reg = <2>; - interrupt-parent = <&switch_intc>; - interrupts = <2>; - }; - ethphy3: phy@3 { - reg = <3>; - interrupt-parent = <&switch_intc>; - interrupts = <3>; - }; - }; -}; diff --git a/Documentation/devicetree/bindings/net/dsa/realtek.yaml b/Documentation/devicetree/bindings/net/dsa/realtek.yaml new file mode 100644 index 0000000..8756060 --- /dev/null +++ b/Documentation/devicetree/bindings/net/dsa/realtek.yaml @@ -0,0 +1,394 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/dsa/realtek.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Realtek switches for unmanaged switches + +allOf: + - $ref: dsa.yaml# + +maintainers: + - Linus Walleij + +description: + Realtek advertises these chips as fast/gigabit switches or unmanaged + switches. They can be controlled using different interfaces, like SMI, + MDIO or SPI. + + The SMI "Simple Management Interface" is a two-wire protocol using + bit-banged GPIO that while it reuses the MDIO lines MCK and MDIO does + not use the MDIO protocol. This binding defines how to specify the + SMI-based Realtek devices. The realtek-smi driver is a platform driver + and it must be inserted inside a platform node. + + The MDIO-connected switches use MDIO protocol to access their registers. + The realtek-mdio driver is an MDIO driver and it must be inserted inside + an MDIO node. + +properties: + compatible: + enum: + - realtek,rtl8365mb + - realtek,rtl8366 + - realtek,rtl8366rb + - realtek,rtl8366s + - realtek,rtl8367 + - realtek,rtl8367b + - realtek,rtl8367rb + - realtek,rtl8367s + - realtek,rtl8368s + - realtek,rtl8369 + - realtek,rtl8370 + description: | + realtek,rtl8365mb: 4+1 ports + realtek,rtl8366: 5+1 ports + realtek,rtl8366rb: 5+1 ports + realtek,rtl8366s: 5+1 ports + realtek,rtl8367: + realtek,rtl8367b: + realtek,rtl8367rb: 5+2 ports + realtek,rtl8367s: 5+2 ports + realtek,rtl8368s: 8 ports + realtek,rtl8369: 8+1 ports + realtek,rtl8370: 8+2 ports + + mdc-gpios: + description: GPIO line for the MDC clock line. + maxItems: 1 + + mdio-gpios: + description: GPIO line for the MDIO data line. + maxItems: 1 + + reset-gpios: + description: GPIO to be used to reset the whole device + maxItems: 1 + + realtek,disable-leds: + type: boolean + description: | + if the LED drivers are not used in the hardware design, + this will disable them so they are not turned on + and wasting power. + + interrupt-controller: + type: object + description: | + This defines an interrupt controller with an IRQ line (typically + a GPIO) that will demultiplex and handle the interrupt from the single + interrupt line coming out of one of the Realtek switch chips. It most + importantly provides link up/down interrupts to the PHY blocks inside + the ASIC. + + properties: + + interrupt-controller: true + + interrupts: + maxItems: 1 + description: + A single IRQ line from the switch, either active LOW or HIGH + + '#address-cells': + const: 0 + + '#interrupt-cells': + const: 1 + + required: + - interrupt-controller + - '#address-cells' + - '#interrupt-cells' + + mdio: + $ref: /schemas/net/mdio.yaml# + unevaluatedProperties: false + + properties: + compatible: + const: realtek,smi-mdio + +if: + required: + - reg + +then: + not: + required: + - mdc-gpios + - mdio-gpios + - mdio + + properties: + mdc-gpios: false + mdio-gpios: false + mdio: false + +else: + required: + - mdc-gpios + - mdio-gpios + - mdio + - reset-gpios + +required: + - compatible + + # - mdc-gpios + # - mdio-gpios + # - reset-gpios + # - mdio + +unevaluatedProperties: false + +examples: + - | + #include + #include + + platform { + switch { + compatible = "realtek,rtl8366rb"; + /* 22 = MDIO (has input reads), 21 = MDC (clock, output only) */ + mdc-gpios = <&gpio0 21 GPIO_ACTIVE_HIGH>; + mdio-gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>; + reset-gpios = <&gpio0 14 GPIO_ACTIVE_LOW>; + + switch_intc1: interrupt-controller { + /* GPIO 15 provides the interrupt */ + interrupt-parent = <&gpio0>; + interrupts = <15 IRQ_TYPE_LEVEL_LOW>; + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <1>; + }; + + ports { + #address-cells = <1>; + #size-cells = <0>; + port@0 { + reg = <0>; + label = "lan0"; + phy-handle = <&phy0>; + }; + port@1 { + reg = <1>; + label = "lan1"; + phy-handle = <&phy1>; + }; + port@2 { + reg = <2>; + label = "lan2"; + phy-handle = <&phy2>; + }; + port@3 { + reg = <3>; + label = "lan3"; + phy-handle = <&phy3>; + }; + port@4 { + reg = <4>; + label = "wan"; + phy-handle = <&phy4>; + }; + port@5 { + reg = <5>; + label = "cpu"; + ethernet = <&gmac0>; + phy-mode = "rgmii"; + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + }; + + mdio { + compatible = "realtek,smi-mdio"; + #address-cells = <1>; + #size-cells = <0>; + + phy0: ethernet-phy@0 { + reg = <0>; + interrupt-parent = <&switch_intc1>; + interrupts = <0>; + }; + phy1: ethernet-phy@1 { + reg = <1>; + interrupt-parent = <&switch_intc1>; + interrupts = <1>; + }; + phy2: ethernet-phy@2 { + reg = <2>; + interrupt-parent = <&switch_intc1>; + interrupts = <2>; + }; + phy3: ethernet-phy@3 { + reg = <3>; + interrupt-parent = <&switch_intc1>; + interrupts = <3>; + }; + phy4: ethernet-phy@4 { + reg = <4>; + interrupt-parent = <&switch_intc1>; + interrupts = <12>; + }; + }; + }; + }; + + - | + #include + #include + + platform { + switch { + compatible = "realtek,rtl8365mb"; + mdc-gpios = <&gpio1 16 GPIO_ACTIVE_HIGH>; + mdio-gpios = <&gpio1 17 GPIO_ACTIVE_HIGH>; + reset-gpios = <&gpio5 0 GPIO_ACTIVE_LOW>; + + switch_intc2: interrupt-controller { + interrupt-parent = <&gpio5>; + interrupts = <1 IRQ_TYPE_LEVEL_LOW>; + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <1>; + }; + + ports { + #address-cells = <1>; + #size-cells = <0>; + port@0 { + reg = <0>; + label = "swp0"; + phy-handle = <ðphy0>; + }; + port@1 { + reg = <1>; + label = "swp1"; + phy-handle = <ðphy1>; + }; + port@2 { + reg = <2>; + label = "swp2"; + phy-handle = <ðphy2>; + }; + port@3 { + reg = <3>; + label = "swp3"; + phy-handle = <ðphy3>; + }; + port@6 { + reg = <6>; + label = "cpu"; + ethernet = <&fec1>; + phy-mode = "rgmii"; + tx-internal-delay-ps = <2000>; + rx-internal-delay-ps = <2000>; + + fixed-link { + speed = <1000>; + full-duplex; + pause; + }; + }; + }; + + mdio { + compatible = "realtek,smi-mdio"; + #address-cells = <1>; + #size-cells = <0>; + + ethphy0: ethernet-phy@0 { + reg = <0>; + interrupt-parent = <&switch_intc2>; + interrupts = <0>; + }; + ethphy1: ethernet-phy@1 { + reg = <1>; + interrupt-parent = <&switch_intc2>; + interrupts = <1>; + }; + ethphy2: ethernet-phy@2 { + reg = <2>; + interrupt-parent = <&switch_intc2>; + interrupts = <2>; + }; + ethphy3: ethernet-phy@3 { + reg = <3>; + interrupt-parent = <&switch_intc2>; + interrupts = <3>; + }; + }; + }; + }; + + - | + #include + #include + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + switch@29 { + compatible = "realtek,rtl8367s"; + reg = <29>; + + reset-gpios = <&gpio2 20 GPIO_ACTIVE_LOW>; + + switch_intc3: interrupt-controller { + interrupt-parent = <&gpio0>; + interrupts = <11 IRQ_TYPE_EDGE_FALLING>; + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <1>; + }; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "lan4"; + }; + + port@1 { + reg = <1>; + label = "lan3"; + }; + + port@2 { + reg = <2>; + label = "lan2"; + }; + + port@3 { + reg = <3>; + label = "lan1"; + }; + + port@4 { + reg = <4>; + label = "wan"; + }; + + port@7 { + reg = <7>; + ethernet = <ðernet>; + phy-mode = "rgmii"; + tx-internal-delay-ps = <2000>; + rx-internal-delay-ps = <0>; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + }; + }; + };