From: Marek Behún Date: Wed, 12 Jan 2022 16:06:59 +0000 (+0100) Subject: ddr: marvell: a38x: fix SPLIT_OUT_MIX state decision X-Git-Tag: v2022.07~230^2~22 X-Git-Url: http://review.tizen.org/git/?a=commitdiff_plain;h=3fc92a215b69ad448c151489228eb340df9a8703;p=platform%2Fkernel%2Fu-boot.git ddr: marvell: a38x: fix SPLIT_OUT_MIX state decision This is a cleaned up and fixed version of a patch mv_ddr: a380: fix SPLIT_OUT_MIX state decision in each pattern cycle the bus state can be changed in order to avoide it, need to back to the same bus state on each pattern cycle by Moti Boskula The original patch is not in Marvell's mv-ddr-marvell repository. It was gives to us by Marvell to fix an issues with DDR training on some boards, but it cannot be applied as is to mv-ddr-marvell, because it is a very dirty draft patch that would certainly break other things, mainly DDR4 training code in mv-ddr-marvell, since it changes common functions. I have cleaned up the patch and removed stuff that seemed unnecessary (when removed, it still fixed things). Note that I don't understand completely what the code does exactly, since I haven't studied the DDR training code extensively (and I suspect that no one besides some few people in Marvell understand the code completely). Anyway after the cleanup the patch still fixes isssues with DDR training on the failing boards. There was also a problem with the original patch on some of the Allied Telesis' x530 boards, reported by Chris Packham. I have asked Chris to send me some logs, and managed to fix it: - if you look at the change, you'll notice that it introduces subtraction of cur_start_win[] and cur_end_win[] members, depending on a bit set in the current_byte_status variable - the original patch subtracted cur_start_win[] if either BYTE_SPLIT_OUT_MIX or BYTE_HOMOGENEOUS_SPLIT_OUT bits were set, but subtracted cur_end_win[] only if the first one (BYTE_SPLIT_OUT_MIX) was set - from Chris Packham logs I discovered that the x530 board where the original patch introduced DDR training failure, only the BYTE_HOMOGENEOUS_SPLIT_OUT bit was set, and on our boards where the patch is needed only the BYTE_SPLIT_OUT_MIX is set in the current_byte_status variable - this led me to the hypothesis that both cur_start_win[] and cur_end_win[] should be subtracted only if BYTE_SPLIT_OUT_MIX bit is set, the BYTE_HOMOGENEOUS_SPLIT_OUT bit shouldn't be considered at all - this hypothesis also gains credibility when considering the commit title ("fix SPLIT_OUT_MIX state decision") Hopefully this will fix things without breaking anything else. Signed-off-by: Marek Behún Reviewed-by: Stefan Roese Tested-by: Chris Packham --- diff --git a/drivers/ddr/marvell/a38x/ddr3_training_centralization.c b/drivers/ddr/marvell/a38x/ddr3_training_centralization.c index 648b37e..42308b6 100644 --- a/drivers/ddr/marvell/a38x/ddr3_training_centralization.c +++ b/drivers/ddr/marvell/a38x/ddr3_training_centralization.c @@ -55,6 +55,7 @@ static int ddr3_tip_centralization(u32 dev_num, u32 mode) enum hws_training_ip_stat training_result[MAX_INTERFACE_NUM]; u32 if_id, pattern_id, bit_id; u8 bus_id; + u8 current_byte_status; u8 cur_start_win[BUS_WIDTH_IN_BITS]; u8 centralization_result[MAX_INTERFACE_NUM][BUS_WIDTH_IN_BITS]; u8 cur_end_win[BUS_WIDTH_IN_BITS]; @@ -166,6 +167,10 @@ static int ddr3_tip_centralization(u32 dev_num, u32 mode) result[search_dir_id][7])); } + current_byte_status = + mv_ddr_tip_sub_phy_byte_status_get(if_id, + bus_id); + for (bit_id = 0; bit_id < BUS_WIDTH_IN_BITS; bit_id++) { /* check if this code is valid for 2 edge, probably not :( */ @@ -174,11 +179,32 @@ static int ddr3_tip_centralization(u32 dev_num, u32 mode) [HWS_LOW2HIGH] [bit_id], EDGE_1); + if (current_byte_status & + BYTE_SPLIT_OUT_MIX) { + if (cur_start_win[bit_id] >= 64) + cur_start_win[bit_id] -= 64; + else + cur_start_win[bit_id] = 0; + DEBUG_CENTRALIZATION_ENGINE + (DEBUG_LEVEL_INFO, + ("pattern %d IF %d pup %d bit %d subtract 64 adll from start\n", + pattern_id, if_id, bus_id, bit_id)); + } cur_end_win[bit_id] = GET_TAP_RESULT(result [HWS_HIGH2LOW] [bit_id], EDGE_1); + if (cur_end_win[bit_id] >= 64 && + (current_byte_status & + BYTE_SPLIT_OUT_MIX)) { + cur_end_win[bit_id] -= 64; + DEBUG_CENTRALIZATION_ENGINE + (DEBUG_LEVEL_INFO, + ("pattern %d IF %d pup %d bit %d subtract 64 adll from end\n", + pattern_id, if_id, bus_id, bit_id)); + } + /* window length */ current_window[bit_id] = cur_end_win[bit_id] -