From: Johan Hovold Date: Fri, 1 Nov 2019 17:24:10 +0000 (+0100) Subject: USB: serial: ch341: reimplement line-speed handling X-Git-Tag: v5.10.7~3801^2~22^2~17 X-Git-Url: http://review.tizen.org/git/?a=commitdiff_plain;h=35714565089e5e8b091c1155517b67e29118f09d;p=platform%2Fkernel%2Flinux-rpi.git USB: serial: ch341: reimplement line-speed handling The current ch341 divisor algorithm was known to give inaccurate results for certain higher line speeds. Jonathan Olds investigated this, determined the basic equations used to derive the divisors and confirmed them experimentally [1]. The equations Jonathan used could be generalised further to: baudrate = 48000000 / (2^(12 - 3 * ps - fact) * div), where 0 <= ps <= 3, 0 <= fact <= 1, 2 <= div <= 256 if fact = 0, or 9 <= div <= 256 if fact = 1 which will also give better results for lower rates. Notably the error is reduced for the following standard rates: 1152000 (4.0% instead of 15% error) 921600 (0.16% instead of -7.5% error) 576000 (-0.80% instead of -5.6% error) 200 (0.16% instead of -0.69% error) 134 (-0.05% instead of -0.63% error) 110 (0.03% instead of -0.44% error) but also for many non-standard ones. The current algorithm also suffered from rounding issues (e.g. requesting 2950000 Bd resulted in a rate of 2 MBd instead of 3 MBd and thus a -32% instead of 1.7% error). The new algorithm was inspired by the current vendor driver even if that one only handles two higher rates that require fact=1 by hard coding the corresponding divisors [2]. Michael Dreher also did a similar generalisation of Jonathan's work and has published his results with a very good summary that provides further insights into how this device works [3]. [1] https://lkml.kernel.org/r/000001d51f34$bad6afd0$30840f70$@co.nz [2] http://www.wch.cn/download/CH341SER_LINUX_ZIP.html [3] https://github.com/nospam2000/ch341-baudrate-calculation Reported-by: Jonathan Olds Tested-by: Jonathan Olds Cc: Michael Dreher Signed-off-by: Johan Hovold --- diff --git a/drivers/usb/serial/ch341.c b/drivers/usb/serial/ch341.c index 3bb1fff..df582fe 100644 --- a/drivers/usb/serial/ch341.c +++ b/drivers/usb/serial/ch341.c @@ -48,12 +48,6 @@ #define CH341_BIT_DCD 0x08 #define CH341_BITS_MODEM_STAT 0x0f /* all bits */ -/*******************************/ -/* baudrate calculation factor */ -/*******************************/ -#define CH341_BAUDBASE_FACTOR 1532620800 -#define CH341_BAUDBASE_DIVMAX 3 - /* Break support - the information used to implement this was gleaned from * the Net/FreeBSD uchcom.c driver by Takanori Watanabe. Domo arigato. */ @@ -144,37 +138,96 @@ static int ch341_control_in(struct usb_device *dev, return 0; } +#define CH341_CLKRATE 48000000 +#define CH341_CLK_DIV(ps, fact) (1 << (12 - 3 * (ps) - (fact))) +#define CH341_MIN_RATE(ps) (CH341_CLKRATE / (CH341_CLK_DIV((ps), 1) * 512)) + +static const speed_t ch341_min_rates[] = { + CH341_MIN_RATE(0), + CH341_MIN_RATE(1), + CH341_MIN_RATE(2), + CH341_MIN_RATE(3), +}; + +/* + * The device line speed is given by the following equation: + * + * baudrate = 48000000 / (2^(12 - 3 * ps - fact) * div), where + * + * 0 <= ps <= 3, + * 0 <= fact <= 1, + * 2 <= div <= 256 if fact = 0, or + * 9 <= div <= 256 if fact = 1 + */ +static int ch341_get_divisor(speed_t speed) +{ + unsigned int fact, div, clk_div; + int ps; + + /* + * Clamp to supported range, this makes the (ps < 0) and (div < 2) + * sanity checks below redundant. + */ + speed = clamp(speed, 46U, 3000000U); + + /* + * Start with highest possible base clock (fact = 1) that will give a + * divisor strictly less than 512. + */ + fact = 1; + for (ps = 3; ps >= 0; ps--) { + if (speed > ch341_min_rates[ps]) + break; + } + + if (ps < 0) + return -EINVAL; + + /* Determine corresponding divisor, rounding down. */ + clk_div = CH341_CLK_DIV(ps, fact); + div = CH341_CLKRATE / (clk_div * speed); + + /* Halve base clock (fact = 0) if required. */ + if (div < 9 || div > 255) { + div /= 2; + clk_div *= 2; + fact = 0; + } + + if (div < 2) + return -EINVAL; + + /* + * Pick next divisor if resulting rate is closer to the requested one, + * scale up to avoid rounding errors on low rates. + */ + if (16 * CH341_CLKRATE / (clk_div * div) - 16 * speed >= + 16 * speed - 16 * CH341_CLKRATE / (clk_div * (div + 1))) + div++; + + return (0x100 - div) << 8 | fact << 2 | ps; +} + static int ch341_set_baudrate_lcr(struct usb_device *dev, struct ch341_private *priv, u8 lcr) { - short a; + int val; int r; - unsigned long factor; - short divisor; if (!priv->baud_rate) return -EINVAL; - factor = (CH341_BAUDBASE_FACTOR / priv->baud_rate); - divisor = CH341_BAUDBASE_DIVMAX; - - while ((factor > 0xfff0) && divisor) { - factor >>= 3; - divisor--; - } - if (factor > 0xfff0) + val = ch341_get_divisor(priv->baud_rate); + if (val < 0) return -EINVAL; - factor = 0x10000 - factor; - a = (factor & 0xff00) | divisor; - /* * CH341A buffers data until a full endpoint-size packet (32 bytes) * has been received unless bit 7 is set. */ - a |= BIT(7); + val |= BIT(7); - r = ch341_control_out(dev, CH341_REQ_WRITE_REG, 0x1312, a); + r = ch341_control_out(dev, CH341_REQ_WRITE_REG, 0x1312, val); if (r) return r;