From: Philipp Zabel Date: Fri, 5 Jun 2009 16:31:05 +0000 (+0200) Subject: mfd: asic3: remove SD/SDIO controller register definitions X-Git-Tag: 2.1b_release~12366^2~4 X-Git-Url: http://review.tizen.org/git/?a=commitdiff_plain;h=1b89040c3aa4500c97859bad714e010441e9c477;p=platform%2Fkernel%2Fkernel-mfld-blackbay.git mfd: asic3: remove SD/SDIO controller register definitions Only the base addresses remain, as they are needed to set up the IOMEM resources. Signed-off-by: Philipp Zabel Signed-off-by: Samuel Ortiz --- diff --git a/include/linux/mfd/asic3.h b/include/linux/mfd/asic3.h index d2ecaaf..de3c4ad 100644 --- a/include/linux/mfd/asic3.h +++ b/include/linux/mfd/asic3.h @@ -286,222 +286,9 @@ struct asic3_platform_data { * SDIO_CTRL Control registers for SDIO operations * *****************************************************************************/ -#define ASIC3_SD_CONFIG_Base 0x0400 /* Assumes 32 bit addressing */ - -#define ASIC3_SD_CONFIG_Command 0x08 /* R/W: Command */ - -/* [0:8] SD Control Register Base Address */ -#define ASIC3_SD_CONFIG_Addr0 0x20 - -/* [9:31] SD Control Register Base Address */ -#define ASIC3_SD_CONFIG_Addr1 0x24 - -/* R/O: interrupt assigned to pin */ -#define ASIC3_SD_CONFIG_IntPin 0x78 - -/* - * Set to 0x1f to clock SD controller, 0 otherwise. - * At 0x82 - Gated Clock Ctrl - */ -#define ASIC3_SD_CONFIG_ClkStop 0x80 - -/* Control clock of SD controller */ -#define ASIC3_SD_CONFIG_ClockMode 0x84 -#define ASIC3_SD_CONFIG_SDHC_PinStatus 0x88 /* R/0: SD pins status */ -#define ASIC3_SD_CONFIG_SDHC_Power1 0x90 /* Power1 - manual pwr ctrl */ - -/* auto power up after card inserted */ -#define ASIC3_SD_CONFIG_SDHC_Power2 0x92 - -/* auto power down when card removed */ -#define ASIC3_SD_CONFIG_SDHC_Power3 0x94 -#define ASIC3_SD_CONFIG_SDHC_CardDetect 0x98 -#define ASIC3_SD_CONFIG_SDHC_Slot 0xA0 /* R/O: support slot number */ -#define ASIC3_SD_CONFIG_SDHC_ExtGateClk1 0x1E0 /* Not used */ -#define ASIC3_SD_CONFIG_SDHC_ExtGateClk2 0x1E2 /* Not used*/ - -/* GPIO Output Reg. , at 0x1EA - GPIO Output Enable Reg. */ -#define ASIC3_SD_CONFIG_SDHC_GPIO_OutAndEnable 0x1E8 -#define ASIC3_SD_CONFIG_SDHC_GPIO_Status 0x1EC /* GPIO Status Reg. */ - -/* Bit 1: double buffer/single buffer */ -#define ASIC3_SD_CONFIG_SDHC_ExtGateClk3 0x1F0 - -/* Memory access enable (set to 1 to access SD Controller) */ -#define SD_CONFIG_COMMAND_MAE (1<<1) - -#define SD_CONFIG_CLK_ENABLE_ALL 0x1f - -#define SD_CONFIG_POWER1_PC_33V 0x0200 /* Set for 3.3 volts */ -#define SD_CONFIG_POWER1_PC_OFF 0x0000 /* Turn off power */ - - /* two bits - number of cycles for card detection */ -#define SD_CONFIG_CARDDETECTMODE_CLK ((x) & 0x3) - - -#define ASIC3_SD_CTRL_Base 0x1000 - -#define ASIC3_SD_CTRL_Cmd 0x00 -#define ASIC3_SD_CTRL_Arg0 0x08 -#define ASIC3_SD_CTRL_Arg1 0x0C -#define ASIC3_SD_CTRL_StopInternal 0x10 -#define ASIC3_SD_CTRL_TransferSectorCount 0x14 -#define ASIC3_SD_CTRL_Response0 0x18 -#define ASIC3_SD_CTRL_Response1 0x1C -#define ASIC3_SD_CTRL_Response2 0x20 -#define ASIC3_SD_CTRL_Response3 0x24 -#define ASIC3_SD_CTRL_Response4 0x28 -#define ASIC3_SD_CTRL_Response5 0x2C -#define ASIC3_SD_CTRL_Response6 0x30 -#define ASIC3_SD_CTRL_Response7 0x34 -#define ASIC3_SD_CTRL_CardStatus 0x38 -#define ASIC3_SD_CTRL_BufferCtrl 0x3C -#define ASIC3_SD_CTRL_IntMaskCard 0x40 -#define ASIC3_SD_CTRL_IntMaskBuffer 0x44 -#define ASIC3_SD_CTRL_CardClockCtrl 0x48 -#define ASIC3_SD_CTRL_MemCardXferDataLen 0x4C -#define ASIC3_SD_CTRL_MemCardOptionSetup 0x50 -#define ASIC3_SD_CTRL_ErrorStatus0 0x58 -#define ASIC3_SD_CTRL_ErrorStatus1 0x5C -#define ASIC3_SD_CTRL_DataPort 0x60 -#define ASIC3_SD_CTRL_TransactionCtrl 0x68 -#define ASIC3_SD_CTRL_SoftwareReset 0x1C0 - -#define SD_CTRL_SOFTWARE_RESET_CLEAR (1<<0) - -#define SD_CTRL_TRANSACTIONCONTROL_SET (1<<8) - -#define SD_CTRL_CARDCLOCKCONTROL_FOR_SD_CARD (1<<15) -#define SD_CTRL_CARDCLOCKCONTROL_ENABLE_CLOCK (1<<8) -#define SD_CTRL_CARDCLOCKCONTROL_CLK_DIV_512 (1<<7) -#define SD_CTRL_CARDCLOCKCONTROL_CLK_DIV_256 (1<<6) -#define SD_CTRL_CARDCLOCKCONTROL_CLK_DIV_128 (1<<5) -#define SD_CTRL_CARDCLOCKCONTROL_CLK_DIV_64 (1<<4) -#define SD_CTRL_CARDCLOCKCONTROL_CLK_DIV_32 (1<<3) -#define SD_CTRL_CARDCLOCKCONTROL_CLK_DIV_16 (1<<2) -#define SD_CTRL_CARDCLOCKCONTROL_CLK_DIV_8 (1<<1) -#define SD_CTRL_CARDCLOCKCONTROL_CLK_DIV_4 (1<<0) -#define SD_CTRL_CARDCLOCKCONTROL_CLK_DIV_2 (0<<0) - -#define MEM_CARD_OPTION_REQUIRED 0x000e -#define MEM_CARD_OPTION_DATA_RESPONSE_TIMEOUT(x) (((x) & 0x0f) << 4) -#define MEM_CARD_OPTION_C2_MODULE_NOT_PRESENT (1<<14) -#define MEM_CARD_OPTION_DATA_XFR_WIDTH_1 (1<<15) -#define MEM_CARD_OPTION_DATA_XFR_WIDTH_4 0 - -#define SD_CTRL_COMMAND_INDEX(x) ((x) & 0x3f) -#define SD_CTRL_COMMAND_TYPE_CMD (0 << 6) -#define SD_CTRL_COMMAND_TYPE_ACMD (1 << 6) -#define SD_CTRL_COMMAND_TYPE_AUTHENTICATION (2 << 6) -#define SD_CTRL_COMMAND_RESPONSE_TYPE_NORMAL (0 << 8) -#define SD_CTRL_COMMAND_RESPONSE_TYPE_EXT_R1 (4 << 8) -#define SD_CTRL_COMMAND_RESPONSE_TYPE_EXT_R1B (5 << 8) -#define SD_CTRL_COMMAND_RESPONSE_TYPE_EXT_R2 (6 << 8) -#define SD_CTRL_COMMAND_RESPONSE_TYPE_EXT_R3 (7 << 8) -#define SD_CTRL_COMMAND_DATA_PRESENT (1 << 11) -#define SD_CTRL_COMMAND_TRANSFER_READ (1 << 12) -#define SD_CTRL_COMMAND_TRANSFER_WRITE (0 << 12) -#define SD_CTRL_COMMAND_MULTI_BLOCK (1 << 13) -#define SD_CTRL_COMMAND_SECURITY_CMD (1 << 14) - -#define SD_CTRL_STOP_INTERNAL_ISSSUE_CMD12 (1 << 0) -#define SD_CTRL_STOP_INTERNAL_AUTO_ISSUE_CMD12 (1 << 8) - -#define SD_CTRL_CARDSTATUS_RESPONSE_END (1 << 0) -#define SD_CTRL_CARDSTATUS_RW_END (1 << 2) -#define SD_CTRL_CARDSTATUS_CARD_REMOVED_0 (1 << 3) -#define SD_CTRL_CARDSTATUS_CARD_INSERTED_0 (1 << 4) -#define SD_CTRL_CARDSTATUS_SIGNAL_STATE_PRESENT_0 (1 << 5) -#define SD_CTRL_CARDSTATUS_WRITE_PROTECT (1 << 7) -#define SD_CTRL_CARDSTATUS_CARD_REMOVED_3 (1 << 8) -#define SD_CTRL_CARDSTATUS_CARD_INSERTED_3 (1 << 9) -#define SD_CTRL_CARDSTATUS_SIGNAL_STATE_PRESENT_3 (1 << 10) - -#define SD_CTRL_BUFFERSTATUS_CMD_INDEX_ERROR (1 << 0) -#define SD_CTRL_BUFFERSTATUS_CRC_ERROR (1 << 1) -#define SD_CTRL_BUFFERSTATUS_STOP_BIT_END_ERROR (1 << 2) -#define SD_CTRL_BUFFERSTATUS_DATA_TIMEOUT (1 << 3) -#define SD_CTRL_BUFFERSTATUS_BUFFER_OVERFLOW (1 << 4) -#define SD_CTRL_BUFFERSTATUS_BUFFER_UNDERFLOW (1 << 5) -#define SD_CTRL_BUFFERSTATUS_CMD_TIMEOUT (1 << 6) -#define SD_CTRL_BUFFERSTATUS_UNK7 (1 << 7) -#define SD_CTRL_BUFFERSTATUS_BUFFER_READ_ENABLE (1 << 8) -#define SD_CTRL_BUFFERSTATUS_BUFFER_WRITE_ENABLE (1 << 9) -#define SD_CTRL_BUFFERSTATUS_ILLEGAL_FUNCTION (1 << 13) -#define SD_CTRL_BUFFERSTATUS_CMD_BUSY (1 << 14) -#define SD_CTRL_BUFFERSTATUS_ILLEGAL_ACCESS (1 << 15) - -#define SD_CTRL_INTMASKCARD_RESPONSE_END (1 << 0) -#define SD_CTRL_INTMASKCARD_RW_END (1 << 2) -#define SD_CTRL_INTMASKCARD_CARD_REMOVED_0 (1 << 3) -#define SD_CTRL_INTMASKCARD_CARD_INSERTED_0 (1 << 4) -#define SD_CTRL_INTMASKCARD_SIGNAL_STATE_PRESENT_0 (1 << 5) -#define SD_CTRL_INTMASKCARD_UNK6 (1 << 6) -#define SD_CTRL_INTMASKCARD_WRITE_PROTECT (1 << 7) -#define SD_CTRL_INTMASKCARD_CARD_REMOVED_3 (1 << 8) -#define SD_CTRL_INTMASKCARD_CARD_INSERTED_3 (1 << 9) -#define SD_CTRL_INTMASKCARD_SIGNAL_STATE_PRESENT_3 (1 << 10) - -#define SD_CTRL_INTMASKBUFFER_CMD_INDEX_ERROR (1 << 0) -#define SD_CTRL_INTMASKBUFFER_CRC_ERROR (1 << 1) -#define SD_CTRL_INTMASKBUFFER_STOP_BIT_END_ERROR (1 << 2) -#define SD_CTRL_INTMASKBUFFER_DATA_TIMEOUT (1 << 3) -#define SD_CTRL_INTMASKBUFFER_BUFFER_OVERFLOW (1 << 4) -#define SD_CTRL_INTMASKBUFFER_BUFFER_UNDERFLOW (1 << 5) -#define SD_CTRL_INTMASKBUFFER_CMD_TIMEOUT (1 << 6) -#define SD_CTRL_INTMASKBUFFER_UNK7 (1 << 7) -#define SD_CTRL_INTMASKBUFFER_BUFFER_READ_ENABLE (1 << 8) -#define SD_CTRL_INTMASKBUFFER_BUFFER_WRITE_ENABLE (1 << 9) -#define SD_CTRL_INTMASKBUFFER_ILLEGAL_FUNCTION (1 << 13) -#define SD_CTRL_INTMASKBUFFER_CMD_BUSY (1 << 14) -#define SD_CTRL_INTMASKBUFFER_ILLEGAL_ACCESS (1 << 15) - -#define SD_CTRL_DETAIL0_RESPONSE_CMD_ERROR (1 << 0) -#define SD_CTRL_DETAIL0_END_BIT_ERROR_FOR_RESPONSE_NON_CMD12 (1 << 2) -#define SD_CTRL_DETAIL0_END_BIT_ERROR_FOR_RESPONSE_CMD12 (1 << 3) -#define SD_CTRL_DETAIL0_END_BIT_ERROR_FOR_READ_DATA (1 << 4) -#define SD_CTRL_DETAIL0_END_BIT_ERROR_FOR_WRITE_CRC_STATUS (1 << 5) -#define SD_CTRL_DETAIL0_CRC_ERROR_FOR_RESPONSE_NON_CMD12 (1 << 8) -#define SD_CTRL_DETAIL0_CRC_ERROR_FOR_RESPONSE_CMD12 (1 << 9) -#define SD_CTRL_DETAIL0_CRC_ERROR_FOR_READ_DATA (1 << 10) -#define SD_CTRL_DETAIL0_CRC_ERROR_FOR_WRITE_CMD (1 << 11) - -#define SD_CTRL_DETAIL1_NO_CMD_RESPONSE (1 << 0) -#define SD_CTRL_DETAIL1_TIMEOUT_READ_DATA (1 << 4) -#define SD_CTRL_DETAIL1_TIMEOUT_CRS_STATUS (1 << 5) -#define SD_CTRL_DETAIL1_TIMEOUT_CRC_BUSY (1 << 6) - -#define ASIC3_SDIO_CTRL_Base 0x1200 - -#define ASIC3_SDIO_CTRL_Cmd 0x00 -#define ASIC3_SDIO_CTRL_CardPortSel 0x04 -#define ASIC3_SDIO_CTRL_Arg0 0x08 -#define ASIC3_SDIO_CTRL_Arg1 0x0C -#define ASIC3_SDIO_CTRL_TransferBlockCount 0x14 -#define ASIC3_SDIO_CTRL_Response0 0x18 -#define ASIC3_SDIO_CTRL_Response1 0x1C -#define ASIC3_SDIO_CTRL_Response2 0x20 -#define ASIC3_SDIO_CTRL_Response3 0x24 -#define ASIC3_SDIO_CTRL_Response4 0x28 -#define ASIC3_SDIO_CTRL_Response5 0x2C -#define ASIC3_SDIO_CTRL_Response6 0x30 -#define ASIC3_SDIO_CTRL_Response7 0x34 -#define ASIC3_SDIO_CTRL_CardStatus 0x38 -#define ASIC3_SDIO_CTRL_BufferCtrl 0x3C -#define ASIC3_SDIO_CTRL_IntMaskCard 0x40 -#define ASIC3_SDIO_CTRL_IntMaskBuffer 0x44 -#define ASIC3_SDIO_CTRL_CardXferDataLen 0x4C -#define ASIC3_SDIO_CTRL_CardOptionSetup 0x50 -#define ASIC3_SDIO_CTRL_ErrorStatus0 0x54 -#define ASIC3_SDIO_CTRL_ErrorStatus1 0x58 -#define ASIC3_SDIO_CTRL_DataPort 0x60 -#define ASIC3_SDIO_CTRL_TransactionCtrl 0x68 -#define ASIC3_SDIO_CTRL_CardIntCtrl 0x6C -#define ASIC3_SDIO_CTRL_ClocknWaitCtrl 0x70 -#define ASIC3_SDIO_CTRL_HostInformation 0x74 -#define ASIC3_SDIO_CTRL_ErrorCtrl 0x78 -#define ASIC3_SDIO_CTRL_LEDCtrl 0x7C -#define ASIC3_SDIO_CTRL_SoftwareReset 0x1C0 +#define ASIC3_SD_CONFIG_BASE 0x0400 /* Assumes 32 bit addressing */ +#define ASIC3_SD_CTRL_BASE 0x1000 +#define ASIC3_SDIO_CTRL_BASE 0x1200 #define ASIC3_MAP_SIZE_32BIT 0x2000 #define ASIC3_MAP_SIZE_16BIT 0x1000