From: Jesse Brandeburg Date: Thu, 26 Jul 2012 02:31:04 +0000 (+0000) Subject: igb: implement 580 MDI setting support X-Git-Tag: v3.7-rc1~145^2~300^2~3 X-Git-Url: http://review.tizen.org/git/?a=commitdiff_plain;h=1b556783abe92d3bfedf0d0eb3af2319947739ae;p=platform%2Fkernel%2Flinux-exynos.git igb: implement 580 MDI setting support In order for igb to support MDI setting support via ethtool this code is needed to allow setting the MDI state via software. This is in regards to the related ethtool patch Signed-off-by: Jesse Brandeburg Tested-by: Aaron Brown aaron.f.brown@intel.com Signed-off-by: Jeff Kirsher --- diff --git a/drivers/net/ethernet/intel/igb/e1000_phy.c b/drivers/net/ethernet/intel/igb/e1000_phy.c index 7be98b6..3404bc7 100644 --- a/drivers/net/ethernet/intel/igb/e1000_phy.c +++ b/drivers/net/ethernet/intel/igb/e1000_phy.c @@ -464,6 +464,32 @@ s32 igb_copper_link_setup_82580(struct e1000_hw *hw) phy_data |= I82580_CFG_ENABLE_DOWNSHIFT; ret_val = phy->ops.write_reg(hw, I82580_CFG_REG, phy_data); + if (ret_val) + goto out; + + /* Set MDI/MDIX mode */ + ret_val = phy->ops.read_reg(hw, I82580_PHY_CTRL_2, &phy_data); + if (ret_val) + goto out; + phy_data &= ~I82580_PHY_CTRL2_MDIX_CFG_MASK; + /* + * Options: + * 0 - Auto (default) + * 1 - MDI mode + * 2 - MDI-X mode + */ + switch (hw->phy.mdix) { + case 1: + break; + case 2: + phy_data |= I82580_PHY_CTRL2_MANUAL_MDIX; + break; + case 0: + default: + phy_data |= I82580_PHY_CTRL2_AUTO_MDI_MDIX; + break; + } + ret_val = hw->phy.ops.write_reg(hw, I82580_PHY_CTRL_2, phy_data); out: return ret_val; @@ -2246,8 +2272,7 @@ s32 igb_phy_force_speed_duplex_82580(struct e1000_hw *hw) if (ret_val) goto out; - phy_data &= ~I82580_PHY_CTRL2_AUTO_MDIX; - phy_data &= ~I82580_PHY_CTRL2_FORCE_MDI_MDIX; + phy_data &= ~I82580_PHY_CTRL2_MDIX_CFG_MASK; ret_val = phy->ops.write_reg(hw, I82580_PHY_CTRL_2, phy_data); if (ret_val) diff --git a/drivers/net/ethernet/intel/igb/e1000_phy.h b/drivers/net/ethernet/intel/igb/e1000_phy.h index 34e4061..6ac3299 100644 --- a/drivers/net/ethernet/intel/igb/e1000_phy.h +++ b/drivers/net/ethernet/intel/igb/e1000_phy.h @@ -111,8 +111,9 @@ s32 igb_check_polarity_m88(struct e1000_hw *hw); #define I82580_PHY_STATUS2_SPEED_100MBPS 0x0100 /* I82580 PHY Control 2 */ -#define I82580_PHY_CTRL2_AUTO_MDIX 0x0400 -#define I82580_PHY_CTRL2_FORCE_MDI_MDIX 0x0200 +#define I82580_PHY_CTRL2_MANUAL_MDIX 0x0200 +#define I82580_PHY_CTRL2_AUTO_MDI_MDIX 0x0400 +#define I82580_PHY_CTRL2_MDIX_CFG_MASK 0x0600 /* I82580 PHY Diagnostics Status */ #define I82580_DSTATUS_CABLE_LENGTH 0x03FC