From: Giuseppe CAVALLARO Date: Wed, 4 Apr 2012 04:33:26 +0000 (+0000) Subject: stmmac: extend CSR Clock Range programming X-Git-Tag: upstream/snapshot3+hdmi~7403^2~589 X-Git-Url: http://review.tizen.org/git/?a=commitdiff_plain;h=18f05d64ec36e27892cc0f55be707762aae053a1;p=platform%2Fadaptation%2Frenesas_rcar%2Frenesas_kernel.git stmmac: extend CSR Clock Range programming The CSR Clock Range has been reworked and new macros has been added in the platform header to allow the CSR Clock Range selection in the GMII Address Register. The previous work didn't add the other fields that can be used to achieve MDC clock of frequency higher than the IEEE 802.3 specified frequency limit of 2.5 MHz and program a clock divider of lower value. On such platforms, these are used indeed so this patch adds them. Signed-off-by: Giuseppe Cavallaro Signed-off-by: David S. Miller --- diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c index 83292f4..1a42014 100644 --- a/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c +++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c @@ -70,7 +70,7 @@ static int stmmac_mdio_read(struct mii_bus *bus, int phyaddr, int phyreg) int data; u16 regValue = (((phyaddr << 11) & (0x0000F800)) | ((phyreg << 6) & (0x000007C0))); - regValue |= MII_BUSY | ((priv->plat->clk_csr & 7) << 2); + regValue |= MII_BUSY | ((priv->plat->clk_csr & 0xF) << 2); if (stmmac_mdio_busy_wait(priv->ioaddr, mii_address)) return -EBUSY; @@ -106,7 +106,7 @@ static int stmmac_mdio_write(struct mii_bus *bus, int phyaddr, int phyreg, (((phyaddr << 11) & (0x0000F800)) | ((phyreg << 6) & (0x000007C0))) | MII_WRITE; - value |= MII_BUSY | ((priv->plat->clk_csr & 7) << 2); + value |= MII_BUSY | ((priv->plat->clk_csr & 0xF) << 2); /* Wait until any existing MII operation is complete */ if (stmmac_mdio_busy_wait(priv->ioaddr, mii_address)) diff --git a/include/linux/stmmac.h b/include/linux/stmmac.h index 4aef9ba..cf64031 100644 --- a/include/linux/stmmac.h +++ b/include/linux/stmmac.h @@ -37,28 +37,29 @@ * This could also be configured at run time using CPU freq framework. */ /* MDC Clock Selection define*/ -#define STMMAC_CSR_60_100M 0 /* MDC = clk_scr_i/42 */ -#define STMMAC_CSR_100_150M 1 /* MDC = clk_scr_i/62 */ -#define STMMAC_CSR_20_35M 2 /* MDC = clk_scr_i/16 */ -#define STMMAC_CSR_35_60M 3 /* MDC = clk_scr_i/26 */ -#define STMMAC_CSR_150_250M 4 /* MDC = clk_scr_i/102 */ -#define STMMAC_CSR_250_300M 5 /* MDC = clk_scr_i/122 */ - -/* FIXME: The MDC clock could be set higher than the IEEE 802.3 +#define STMMAC_CSR_60_100M 0x0 /* MDC = clk_scr_i/42 */ +#define STMMAC_CSR_100_150M 0x1 /* MDC = clk_scr_i/62 */ +#define STMMAC_CSR_20_35M 0x2 /* MDC = clk_scr_i/16 */ +#define STMMAC_CSR_35_60M 0x3 /* MDC = clk_scr_i/26 */ +#define STMMAC_CSR_150_250M 0x4 /* MDC = clk_scr_i/102 */ +#define STMMAC_CSR_250_300M 0x5 /* MDC = clk_scr_i/122 */ + +/* The MDC clock could be set higher than the IEEE 802.3 * specified frequency limit 0f 2.5 MHz, by programming a clock divider * of value different than the above defined values. The resultant MDIO * clock frequency of 12.5 MHz is applicable for the interfacing chips * supporting higher MDC clocks. * The MDC clock selection macros need to be defined for MDC clock rate * of 12.5 MHz, corresponding to the following selection. - * 1000 clk_csr_i/4 - * 1001 clk_csr_i/6 - * 1010 clk_csr_i/8 - * 1011 clk_csr_i/10 - * 1100 clk_csr_i/12 - * 1101 clk_csr_i/14 - * 1110 clk_csr_i/16 - * 1111 clk_csr_i/18 */ + */ +#define STMMAC_CSR_I_4 0x8 /* clk_csr_i/4 */ +#define STMMAC_CSR_I_6 0x9 /* clk_csr_i/6 */ +#define STMMAC_CSR_I_8 0xA /* clk_csr_i/8 */ +#define STMMAC_CSR_I_10 0xB /* clk_csr_i/10 */ +#define STMMAC_CSR_I_12 0xC /* clk_csr_i/12 */ +#define STMMAC_CSR_I_14 0xD /* clk_csr_i/14 */ +#define STMMAC_CSR_I_16 0xE /* clk_csr_i/16 */ +#define STMMAC_CSR_I_18 0xF /* clk_csr_i/18 */ /* AXI DMA Burst length suported */ #define DMA_AXI_BLEN_4 (1 << 1)