From: Christophe Leroy Date: Wed, 22 May 2019 12:17:11 +0000 (+0000) Subject: tty: serial: cpm_uart - fix init when SMC is relocated X-Git-Tag: v5.4-rc1~601^2~51 X-Git-Url: http://review.tizen.org/git/?a=commitdiff_plain;h=06aaa3d066db87e8478522d910285141d44b1e58;p=platform%2Fkernel%2Flinux-rpi.git tty: serial: cpm_uart - fix init when SMC is relocated SMC relocation can also be activated earlier by the bootloader, so the driver's behaviour cannot rely on selected kernel config. When the SMC is relocated, CPM_CR_INIT_TRX cannot be used. But the only thing CPM_CR_INIT_TRX does is to clear the rstate and tstate registers, so this can be done manually, even when SMC is not relocated. Signed-off-by: Christophe Leroy Fixes: 9ab921201444 ("cpm_uart: fix non-console port startup bug") Signed-off-by: Greg Kroah-Hartman --- diff --git a/drivers/tty/serial/cpm_uart/cpm_uart_core.c b/drivers/tty/serial/cpm_uart/cpm_uart_core.c index b929c7a..7bab9a3 100644 --- a/drivers/tty/serial/cpm_uart/cpm_uart_core.c +++ b/drivers/tty/serial/cpm_uart/cpm_uart_core.c @@ -407,7 +407,16 @@ static int cpm_uart_startup(struct uart_port *port) clrbits16(&pinfo->sccp->scc_sccm, UART_SCCM_RX); } cpm_uart_initbd(pinfo); - cpm_line_cr_cmd(pinfo, CPM_CR_INIT_TRX); + if (IS_SMC(pinfo)) { + out_be32(&pinfo->smcup->smc_rstate, 0); + out_be32(&pinfo->smcup->smc_tstate, 0); + out_be16(&pinfo->smcup->smc_rbptr, + in_be16(&pinfo->smcup->smc_rbase)); + out_be16(&pinfo->smcup->smc_tbptr, + in_be16(&pinfo->smcup->smc_tbase)); + } else { + cpm_line_cr_cmd(pinfo, CPM_CR_INIT_TRX); + } } /* Install interrupt handler. */ retval = request_irq(port->irq, cpm_uart_int, 0, "cpm_uart", port); @@ -861,16 +870,14 @@ static void cpm_uart_init_smc(struct uart_cpm_port *pinfo) (u8 __iomem *)pinfo->tx_bd_base - DPRAM_BASE); /* - * In case SMC1 is being relocated... + * In case SMC is being relocated... */ -#if defined (CONFIG_I2C_SPI_SMC1_UCODE_PATCH) out_be16(&up->smc_rbptr, in_be16(&pinfo->smcup->smc_rbase)); out_be16(&up->smc_tbptr, in_be16(&pinfo->smcup->smc_tbase)); out_be32(&up->smc_rstate, 0); out_be32(&up->smc_tstate, 0); out_be16(&up->smc_brkcr, 1); /* number of break chars */ out_be16(&up->smc_brkec, 0); -#endif /* Set up the uart parameters in the * parameter ram. @@ -884,8 +891,6 @@ static void cpm_uart_init_smc(struct uart_cpm_port *pinfo) out_be16(&up->smc_brkec, 0); out_be16(&up->smc_brkcr, 1); - cpm_line_cr_cmd(pinfo, CPM_CR_INIT_TRX); - /* Set UART mode, 8 bit, no parity, one stop. * Enable receive and transmit. */