staging: et131x: Remove module_param et131x_speed_set

Manual setting of speed/duplex will be achieved using ethtool.
Remove the driver specific module_param that also does this.

Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

diff --git a/drivers/staging/et131x/et131x_initpci.c b/drivers/staging/et131x/et131x_initpci.c
index 813a72f..a184ac1 100644 (file)
--- a/drivers/staging/et131x/et131x_initpci.c
+++ b/drivers/staging/et131x/et131x_initpci.c
@@ -1,6 +1,6 @@
 /*
  * Agere Systems Inc.
- * 10/100/1000 Base-T Ethernet Driver for the ET1301 and ET131x series MACs
+ * 10/100/1000 Base-T Ethernet Driver for the ET1310 and ET131x series MACs
  *
  * Copyright © 2005 Agere Systems Inc.
  * All rights reserved.
@@ -97,30 +97,6 @@
 #define INTERNAL_MEM_SIZE       0x400  /* 1024 of internal memory */
 #define INTERNAL_MEM_RX_OFFSET  0x1FF  /* 50%   Tx, 50%   Rx */
 
-/* Defines for Parameter Default/Min/Max vaules */
-#define PARM_SPEED_DUPLEX_MIN   0
-#define PARM_SPEED_DUPLEX_MAX   5
-
-/* Module parameter for manual speed setting
- * Set Link speed and dublex manually (0-5)  [0]
- *  1 : 10Mb   Half-Duplex
- *  2 : 10Mb   Full-Duplex
- *  3 : 100Mb  Half-Duplex
- *  4 : 100Mb  Full-Duplex
- *  5 : 1000Mb Full-Duplex
- *  0 : Auto Speed Auto Duplex // default
- */
-static u32 et131x_speed_set;
-module_param(et131x_speed_set, uint, 0);
-MODULE_PARM_DESC(et131x_speed_set,
-               "Set Link speed and dublex manually (0-5)  [0]\n"
-               "1 : 10Mb   Half-Duplex\n"
-               "2 : 10Mb   Full-Duplex\n"
-               "3 : 100Mb  Half-Duplex\n"
-               "4 : 100Mb  Full-Duplex\n"
-               "5 : 1000Mb Full-Duplex\n"
-               "0 : Auto Speed Auto Dublex");
-
 /**
  * et131x_hwaddr_init - set up the MAC Address on the ET1310
  * @adapter: pointer to our private adapter structure
@@ -531,29 +507,12 @@ static struct et131x_adapter *et131x_adapter_init(struct net_device *netdev,
        spin_lock_init(&adapter->fbr_lock);
        spin_lock_init(&adapter->phy_lock);
 
-       /* Parse configuration parameters into the private adapter struct */
-       if (et131x_speed_set)
-               dev_info(&adapter->pdev->dev,
-                       "Speed set manually to : %d\n", et131x_speed_set);
-
-       adapter->speed_duplex = et131x_speed_set;
+       adapter->speed_duplex = 0; /* Auto Speed Auto Duplex */
        adapter->registry_jumbo_packet = 1514;  /* 1514-9216 */
 
        /* Set the MAC address to a default */
        memcpy(adapter->addr, default_mac, ETH_ALEN);
 
-       /* Decode speed_duplex
-        *
-        * Set up as if we are auto negotiating always and then change if we
-        * go into force mode
-        *
-        * If we are the 10/100 device, and gigabit is somehow requested then
-        * knock it down to 100 full.
-        */
-       if (adapter->pdev->device == ET131X_PCI_DEVICE_ID_FAST &&
-           adapter->speed_duplex == 5)
-               adapter->speed_duplex = 4;
-
        adapter->ai_force_speed = speed[adapter->speed_duplex];
        adapter->ai_force_duplex = duplex[adapter->speed_duplex];       /* Auto FDX */
 
@@ -790,11 +749,6 @@ static struct pci_driver et131x_driver = {
  */
 static int __init et131x_init_module(void)
 {
-       if (et131x_speed_set < PARM_SPEED_DUPLEX_MIN ||
-           et131x_speed_set > PARM_SPEED_DUPLEX_MAX) {
-               printk(KERN_WARNING "et131x: invalid speed setting ignored.\n");
-               et131x_speed_set = 0;
-       }
        return pci_register_driver(&et131x_driver);
 }