--- /dev/null
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2018 B&R Industrial Automation GmbH
+ * http://www.br-automation.com
+ *
+ */
+/dts-v1/;
+
+#include "am33xx.dtsi"
+
+/ {
+ model = "BRPPT1 (MMC) Panel";
+ compatible = "ti,am33xx";
+
+ fset: factory-settings {
+ bl-version = "ABCDEFGHIJKLMNOPQRSTUVWXYZ0123456890";
+ version = <0x0100>;
+ order-no = "6PPT30 (MMC)";
+ hw-revision = "ABCDEFGHIJKLMNOPQRSTUVWXYZ0123456890";
+ serial-no = "0";
+ device-id = <0x0>;
+ parent-id = <0x0>;
+ hw-variant = <0x1>;
+ };
+
+ aliases {
+ ds1bkl0 = &pwmbacklight;
+ ds1bkl1 = &tps_bl;
+ ds1timing = &timing0;
+ ds1ctrl = &lcdc;
+ gpmc = &gpmc;
+ mmc = &mmc2;
+ fset = &fset;
+ };
+
+ chosen {
+ bootargs = "console=ttyO0,115200 earlyprintk";
+ stdout-path = &uart0;
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0x80000000 0x10000000>; /* 256 MB */
+ };
+
+ panel {
+ status = "disabled";
+
+ compatible = "ti,tilcdc,panel";
+ enable-gpios = <&gpio0 6 GPIO_ACTIVE_LOW>;
+
+ backlight = <&pwmbacklight>;
+ bkl-pwm = <&pwmbacklight>;
+ bkl-tps = <&tps_bl>;
+
+ panel-info {
+ ac-bias = <255>;
+ ac-bias-intrpt = <0>;
+ dma-burst-sz = <16>;
+ bpp = <32>;
+ fdd = <0x80>;
+ sync-edge = <0>;
+ sync-ctrl = <1>;
+ raster-order = <0>;
+ fifo-th = <0>;
+ };
+
+ display-timings {
+ native-mode = <&timing0>;
+ timing0: lcd {
+ clock-frequency = <32000000>;
+ hactive = <800>;
+ vactive = <480>;
+ hfront-porch = <2>;
+ hback-porch = <192>;
+ hsync-len = <1>;
+ vfront-porch = <20>;
+ vback-porch = <2>;
+ vsync-len = <1>;
+ hsync-active = <1>;
+ vsync-active = <1>;
+ pupdelay = <10>;
+ pondelay = <10>;
+ };
+ };
+ };
+
+ vmmcsd_fixed: fixedregulator@0 {
+ compatible = "regulator-fixed";
+ regulator-name = "vmmcsd_fixed";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ pwm0: omap-pwm@timer5 {
+ compatible = "ti,omap-dmtimer-pwm";
+ ti,timers = <&timer5>;
+ #pwm-cells = <3>;
+ };
+
+ pwm1: omap-pwm@timer6 {
+ compatible = "ti,omap-dmtimer-pwm";
+ ti,timers = <&timer6>;
+ #pwm-cells = <3>;
+ };
+
+ beeper: pwm-beep {
+ compatible = "pwm-beeper";
+ pwms = <&pwm0 0 0 0>;
+ };
+
+ pwmbacklight: pwm-bkl {
+ compatible = "pwm-backlight";
+ pwms = <&pwm1 0 5000000 0>;
+
+ default-brightness-level = <255>;
+ brightness-levels = <0 16 32 64 128 170 202 234 255>;
+
+ power-supply = <&vmmcsd_fixed>;
+ enable-gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+&uart0 { /* console uart */
+ u-boot,dm-spl;
+ status = "okay";
+};
+
+&uart1 {
+ status = "okay";
+};
+
+&i2c0 {
+ u-boot,dm-spl;
+ status = "okay";
+ clock-frequency = <400000>;
+
+ tps: tps@24 { /* PMIC controller */
+ u-boot,dm-spl;
+ reg = <0x24>;
+ compatible = "ti,tps65217";
+
+ tps_bl: backlight {
+ compatible = "ti,tps65217-bl";
+ isel = <1>; /* 1 - ISET1, 2 ISET2 */
+ fdim = <1000>; /* TPS65217_BL_FDIM_1kHZ */
+ default-brightness = <50>;
+ };
+ };
+};
+
+&i2c2 {
+ status = "okay";
+ clock-frequency = <100000>;
+};
+
+&edma {
+ status = "okay";
+};
+
+&cppi41dma {
+ status = "okay";
+};
+
+&usb {
+ status = "okay";
+};
+
+&usb_ctrl_mod {
+ status = "okay";
+};
+
+&usb0_phy {
+ status = "okay";
+};
+
+&usb1_phy {
+ status = "okay";
+};
+
+&usb0 {
+ status = "okay";
+ dr_mode = "host";
+};
+
+&usb1 {
+ status = "okay";
+ dr_mode = "host";
+};
+
+&davinci_mdio {
+ status = "okay";
+
+ phy0: ethernet-phy@0 {
+ reg = <1>;
+ };
+
+ phy1: ethernet-phy@1 {
+ reg = <2>;
+ };
+};
+
+&mac {
+ status = "okay";
+};
+
+&cpsw_emac0 {
+ phy-handle = <&phy0>;
+ dual_emac_res_vlan = <1>;
+ phy-mode = "mii";
+};
+
+&cpsw_emac1 {
+ phy-handle = <&phy1>;
+ dual_emac_res_vlan = <2>;
+ phy-mode = "mii";
+};
+
+&mmc1 {
+ u-boot,dm-spl;
+ vmmc-supply = <&vmmcsd_fixed>;
+ bus-width = <0x4>;
+ ti,non-removable;
+ ti,needs-special-hs-handling;
+ ti,vcc-aux-disable-is-sleep;
+ status = "okay";
+};
+
+&mmc2 {
+ u-boot,dm-spl;
+ vmmc-supply = <&vmmcsd_fixed>;
+ bus-width = <0x8>;
+ ti,non-removable;
+ ti,needs-special-hs-handling;
+ ti,vcc-aux-disable-is-sleep;
+ status = "okay";
+};
+
+&lcdc {
+ status = "disabled";
+};
+
+&elm {
+ status = "okay";
+};
+
+&sham {
+ status = "okay";
+};
+
+&aes {
+ status = "okay";
+};
+
+&gpio0 {
+ u-boot,dm-spl;
+ ti,no-reset-on-init;
+};
+
+&gpio1 {
+ u-boot,dm-spl;
+ ti,no-reset-on-init;
+};
+
+&gpio2 {
+ u-boot,dm-spl;
+ ti,no-reset-on-init;
+};
+
+&gpio3 {
+ u-boot,dm-spl;
+ ti,no-reset-on-init;
+};
+
+&wdt2 {
+ ti,no-reset-on-init;
+ ti,no-idle-on-init;
+};
+
+&tscadc {
+ status = "okay";
+ tsc {
+ ti,wires = <4>;
+ ti,x-plate-resistance = <200>;
+ ti,zx-cutoff-ratio = <40>;
+ ti,min_deviation = <60>;
+ ti,max_deviation = <600>;
+ ti,coordinate-readouts = <5>;
+ ti,wire-config = <0x00 0x11 0x22 0x33>;
+
+ bnr-buttons {
+ Home-Button {};
+ };
+ };
+
+ adc {
+ ti,adc-channels = <5 6 7>;
+ };
+};
+
+&timer6 { /* used for cpsw end device */
+ status = "okay";
+ ti,no-reset-on-init;
+ ti,no-idle-on-init;
+};
+
+&timer7 { /* used for cpsw end device */
+ status = "okay";
+ ti,no-reset-on-init;
+ ti,no-idle-on-init;
+};
+
+&wdt2 {
+ status = "okay";
+ ti,no-reset-on-init;
+ ti,no-idle-on-init;
+};
+
+&epwmss0 {
+ status = "okay";
+};
+
+&tscadc {
+ status = "okay";
+};
+
+&dcan0 {
+ status = "okay";
+};
+
+&dcan1 {
+ status = "okay";
+};
+
+&sham {
+ status = "disabled";
+};
+
+&aes {
+ status = "disabled";
+};
+
+&rng {
+ status = "disabled";
+};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2018 B&R Industrial Automation GmbH
+ * http://www.br-automation.com
+ *
+ */
+/dts-v1/;
+
+#include "am33xx.dtsi"
+
+/ {
+ model = "BRPPT1 (NAND) Panel";
+ compatible = "ti,am33xx";
+
+ fset: factory-settings {
+ bl-version = "ABCDEFGHIJKLMNOPQRSTUVWXYZ0123456890";
+ version = <0x0100>;
+ order-no = "6PPT30 (NAND)";
+ hw-revision = "ABCDEFGHIJKLMNOPQRSTUVWXYZ0123456890";
+ serial-no = "0";
+ device-id = <0x0>;
+ parent-id = <0x0>;
+ hw-variant = <0x1>;
+ };
+
+ aliases {
+ ds1bkl0 = &pwmbacklight;
+ ds1bkl1 = &tps_bl;
+ ds1timing = &timing0;
+ ds1ctrl = &lcdc;
+ gpmc = &gpmc;
+ mmc = &mmc2;
+ fset = &fset;
+ };
+
+ chosen {
+ bootargs = "console=ttyO0,115200 earlyprintk";
+ stdout-path = &uart0;
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0x80000000 0x10000000>; /* 256 MB */
+ };
+
+ panel {
+ status = "disabled";
+
+ compatible = "ti,tilcdc,panel";
+ enable-gpios = <&gpio0 6 GPIO_ACTIVE_LOW>;
+
+ backlight = <&pwmbacklight>;
+ bkl-pwm = <&pwmbacklight>;
+ bkl-tps = <&tps_bl>;
+
+ panel-info {
+ ac-bias = <255>;
+ ac-bias-intrpt = <0>;
+ dma-burst-sz = <16>;
+ bpp = <32>;
+ fdd = <0x80>;
+ sync-edge = <0>;
+ sync-ctrl = <1>;
+ raster-order = <0>;
+ fifo-th = <0>;
+ };
+
+ display-timings {
+ native-mode = <&timing0>;
+ timing0: lcd {
+ clock-frequency = <32000000>;
+ hactive = <800>;
+ vactive = <480>;
+ hfront-porch = <2>;
+ hback-porch = <192>;
+ hsync-len = <1>;
+ vfront-porch = <20>;
+ vback-porch = <2>;
+ vsync-len = <1>;
+ hsync-active = <1>;
+ vsync-active = <1>;
+ pupdelay = <10>;
+ pondelay = <10>;
+ };
+ };
+ };
+
+ vmmcsd_fixed: fixedregulator@0 {
+ compatible = "regulator-fixed";
+ regulator-name = "vmmcsd_fixed";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ pwm0: omap-pwm@timer5 {
+ compatible = "ti,omap-dmtimer-pwm";
+ ti,timers = <&timer5>;
+ #pwm-cells = <3>;
+ };
+
+ pwm1: omap-pwm@timer6 {
+ compatible = "ti,omap-dmtimer-pwm";
+ ti,timers = <&timer6>;
+ #pwm-cells = <3>;
+ };
+
+ beeper: pwm-beep {
+ compatible = "pwm-beeper";
+ pwms = <&pwm0 0 0 0>;
+ };
+
+ pwmbacklight: pwm-bkl {
+ compatible = "pwm-backlight";
+ pwms = <&pwm1 0 5000000 0>;
+
+ default-brightness-level = <255>;
+ brightness-levels = <0 16 32 64 128 170 202 234 255>;
+
+ power-supply = <&vmmcsd_fixed>;
+ enable-gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+&uart0 { /* console uart */
+ u-boot,dm-spl;
+ status = "okay";
+};
+
+&uart1 {
+ status = "okay";
+};
+
+&i2c0 {
+ u-boot,dm-spl;
+ status = "okay";
+ clock-frequency = <400000>;
+
+ tps: tps@24 { /* PMIC controller */
+ u-boot,dm-spl;
+ reg = <0x24>;
+ compatible = "ti,tps65217";
+
+ tps_bl: backlight {
+ compatible = "ti,tps65217-bl";
+ isel = <1>; /* 1 - ISET1, 2 ISET2 */
+ fdim = <1000>; /* TPS65217_BL_FDIM_1kHZ */
+ default-brightness = <50>;
+ };
+ };
+};
+
+&i2c2 {
+ status = "okay";
+ clock-frequency = <100000>;
+};
+
+&edma {
+ status = "okay";
+};
+
+&cppi41dma {
+ status = "okay";
+};
+
+&usb {
+ status = "okay";
+};
+
+&usb_ctrl_mod {
+ status = "okay";
+};
+
+&usb0_phy {
+ status = "okay";
+};
+
+&usb1_phy {
+ status = "okay";
+};
+
+&usb0 {
+ status = "okay";
+ dr_mode = "host";
+};
+
+&usb1 {
+ status = "okay";
+ dr_mode = "host";
+};
+
+&davinci_mdio {
+ status = "okay";
+
+ phy0: ethernet-phy@0 {
+ reg = <1>;
+ };
+
+ phy1: ethernet-phy@1 {
+ reg = <2>;
+ };
+};
+
+&mac {
+ dual_emac;
+ status = "okay";
+};
+
+&cpsw_emac0 {
+ phy-handle = <&phy0>;
+ dual_emac_res_vlan = <1>;
+ phy-mode = "mii";
+};
+
+&cpsw_emac1 {
+ phy-handle = <&phy1>;
+ dual_emac_res_vlan = <2>;
+ phy-mode = "mii";
+};
+
+&mmc2 {
+ vmmc-supply = <&vmmcsd_fixed>;
+ bus-width = <0x4>;
+ ti,non-removable;
+ ti,needs-special-hs-handling;
+ ti,vcc-aux-disable-is-sleep;
+ status = "disabled";
+};
+
+&lcdc {
+ status = "disabled";
+};
+
+&elm {
+ status = "okay";
+};
+
+&sham {
+ status = "okay";
+};
+
+&aes {
+ status = "okay";
+};
+
+&gpio0 {
+ u-boot,dm-spl;
+ ti,no-reset-on-init;
+};
+
+&gpio1 {
+ u-boot,dm-spl;
+ ti,no-reset-on-init;
+};
+
+&gpio2 {
+ u-boot,dm-spl;
+ ti,no-reset-on-init;
+};
+
+&gpio3 {
+ u-boot,dm-spl;
+ ti,no-reset-on-init;
+};
+
+&wdt2 {
+ ti,no-reset-on-init;
+ ti,no-idle-on-init;
+};
+
+&tscadc {
+ status = "okay";
+ tsc {
+ ti,wires = <4>;
+ ti,x-plate-resistance = <200>;
+ ti,zx-cutoff-ratio = <40>;
+ ti,min_deviation = <60>;
+ ti,max_deviation = <600>;
+ ti,coordinate-readouts = <5>;
+ ti,wire-config = <0x00 0x11 0x22 0x33>;
+
+ bnr-buttons {
+ Home-Button {};
+ };
+ };
+
+ adc {
+ ti,adc-channels = <5 6 7>;
+ };
+};
+
+&gpmc {
+ u-boot,dm-spl;
+ status = "okay";
+ pinctrl-names = "default";
+ ranges = <0 0 0x08000000 0x10000000>; /* CS0: NAND */
+ nand@0,0 {
+ compatible = "ti,omap2-nand";
+ reg = <0 0 4>; /* CS0, offset 0, IO size 4 */
+ interrupt-parent = <&gpmc>;
+ rb-gpios = <&gpmc 1 GPIO_ACTIVE_HIGH>; /* gpmc_wait1 */
+ ti,nand-ecc-opt = "bch8";
+ ti,elm-id = <&elm>;
+ nand-bus-width = <8>;
+ gpmc,device-width = <1>;
+ gpmc,sync-clk-ps = <0>;
+ gpmc,cs-on-ns = <0>;
+ gpmc,cs-rd-off-ns = <44>;
+ gpmc,cs-wr-off-ns = <44>;
+ gpmc,adv-on-ns = <6>;
+ gpmc,adv-rd-off-ns = <34>;
+ gpmc,adv-wr-off-ns = <44>;
+ gpmc,we-on-ns = <0>;
+ gpmc,we-off-ns = <40>;
+ gpmc,oe-on-ns = <0>;
+ gpmc,oe-off-ns = <54>;
+ gpmc,access-ns = <64>;
+ gpmc,rd-cycle-ns = <82>;
+ gpmc,wr-cycle-ns = <82>;
+ gpmc,wait-on-read = "true";
+ gpmc,wait-on-write = "true";
+ gpmc,bus-turnaround-ns = <0>;
+ gpmc,cycle2cycle-delay-ns = <0>;
+ gpmc,clk-activation-ns = <0>;
+ gpmc,wait-monitoring-ns = <0>;
+ gpmc,wr-access-ns = <40>;
+ gpmc,wr-data-mux-bus-ns = <0>;
+ gpmc,wait-pin = <1>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ partition@0 {
+ label = "NAND.MLO";
+ reg = <0x00000000 0x000020000>;
+ };
+ partition@1 {
+ label = "NAND.cfgscr";
+ reg = <0x00020000 0x00020000>;
+ };
+ partition@2 {
+ label = "NAND.dtb";
+ reg = <0x00040000 0x00020000>;
+ };
+ partition@3 {
+ label = "NAND.u-boot-env";
+ reg = <0x00060000 0x00020000>;
+ };
+ partition@4 {
+ label = "NAND.u-boot";
+ reg = <0x00080000 0x00080000>;
+ };
+ partition@5 {
+ label = "NAND.kernel";
+ reg = <0x00100000 0x00400000>;
+ };
+ partition@6 {
+ label = "NAND.rootfs";
+ reg = <0x00500000 0x08000000>;
+ };
+ partition@7 {
+ label = "NAND.user";
+ reg = <0x08500000 0x17b00000>;
+ };
+ };
+};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2018 B&R Industrial Automation GmbH
+ * http://www.br-automation.com
+ *
+ */
+/dts-v1/;
+
+#include "am33xx.dtsi"
+
+/ {
+ model = "BRPPT1 (MMC) Panel";
+ compatible = "ti,am33xx";
+
+ fset: factory-settings {
+ bl-version = "ABCDEFGHIJKLMNOPQRSTUVWXYZ0123456890";
+ version = <0x0100>;
+ order-no = "6PPT30 (SPI)";
+ hw-revision = "ABCDEFGHIJKLMNOPQRSTUVWXYZ0123456890";
+ serial-no = "0";
+ device-id = <0x0>;
+ parent-id = <0x0>;
+ hw-variant = <0x1>;
+ };
+
+ aliases {
+ ds1bkl0 = &pwmbacklight;
+ ds1bkl1 = &tps_bl;
+ ds1timing = &timing0;
+ ds1ctrl = &lcdc;
+ gpmc = &gpmc;
+ mmc = &mmc2;
+ spi0 = &spi0;
+ fset = &fset;
+ };
+
+ chosen {
+ bootargs = "console=ttyO0,115200 earlyprintk";
+ stdout-path = &uart0;
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0x80000000 0x10000000>; /* 256 MB */
+ };
+
+ panel {
+ status = "disabled";
+
+ compatible = "ti,tilcdc,panel";
+ enable-gpios = <&gpio0 6 GPIO_ACTIVE_LOW>;
+
+ backlight = <&pwmbacklight>;
+ bkl-pwm = <&pwmbacklight>;
+ bkl-tps = <&tps_bl>;
+
+ panel-info {
+ ac-bias = <255>;
+ ac-bias-intrpt = <0>;
+ dma-burst-sz = <16>;
+ bpp = <32>;
+ fdd = <0x80>;
+ sync-edge = <0>;
+ sync-ctrl = <1>;
+ raster-order = <0>;
+ fifo-th = <0>;
+ };
+
+ display-timings {
+ native-mode = <&timing0>;
+ timing0: lcd {
+ clock-frequency = <32000000>;
+ hactive = <800>;
+ vactive = <480>;
+ hfront-porch = <2>;
+ hback-porch = <192>;
+ hsync-len = <1>;
+ vfront-porch = <20>;
+ vback-porch = <2>;
+ vsync-len = <1>;
+ hsync-active = <1>;
+ vsync-active = <1>;
+ pupdelay = <10>;
+ pondelay = <10>;
+ };
+ };
+ };
+
+ vmmcsd_fixed: fixedregulator@0 {
+ compatible = "regulator-fixed";
+ regulator-name = "vmmcsd_fixed";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ pwm0: omap-pwm@timer5 {
+ compatible = "ti,omap-dmtimer-pwm";
+ ti,timers = <&timer5>;
+ #pwm-cells = <3>;
+ };
+
+ pwm1: omap-pwm@timer6 {
+ compatible = "ti,omap-dmtimer-pwm";
+ ti,timers = <&timer6>;
+ #pwm-cells = <3>;
+ };
+
+ beeper: pwm-beep {
+ compatible = "pwm-beeper";
+ pwms = <&pwm0 0 0 0>;
+ };
+
+ pwmbacklight: pwm-bkl {
+ compatible = "pwm-backlight";
+ pwms = <&pwm1 0 5000000 0>;
+
+ default-brightness-level = <255>;
+ brightness-levels = <0 16 32 64 128 170 202 234 255>;
+
+ power-supply = <&vmmcsd_fixed>;
+ enable-gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+&uart0 { /* console uart */
+ u-boot,dm-spl;
+ status = "okay";
+};
+
+&uart1 {
+ status = "okay";
+};
+
+&i2c0 {
+ u-boot,dm-spl;
+ status = "okay";
+ clock-frequency = <400000>;
+
+ tps: tps@24 { /* PMIC controller */
+ u-boot,dm-spl;
+ reg = <0x24>;
+ compatible = "ti,tps65217";
+
+ tps_bl: backlight {
+ compatible = "ti,tps65217-bl";
+ isel = <1>; /* 1 - ISET1, 2 ISET2 */
+ fdim = <1000>; /* TPS65217_BL_FDIM_1kHZ */
+ default-brightness = <50>;
+ };
+ };
+};
+
+&i2c2 {
+ status = "okay";
+ clock-frequency = <100000>;
+};
+
+&spi0 {
+ u-boot,dm-spl;
+ status = "okay";
+
+ cs-gpios = <&gpio0 5 GPIO_ACTIVE_HIGH>,
+ <&gpio0 6 GPIO_ACTIVE_HIGH>,
+ <0>,
+ <0>;
+
+ spi-max-frequency = <24000000>;
+
+ spi_flash: spiflash@0 {
+ u-boot,dm-spl;
+ u-boot,dm-pre-reloc;
+ compatible = "spidev", "spi-flash";
+ spi-max-frequency = <24000000>;
+ reg = <0>;
+ };
+};
+
+&edma {
+ status = "okay";
+};
+
+&cppi41dma {
+ status = "okay";
+};
+
+&usb {
+ status = "okay";
+};
+
+&usb_ctrl_mod {
+ status = "okay";
+};
+
+&usb0_phy {
+ status = "okay";
+};
+
+&usb1_phy {
+ status = "okay";
+};
+
+&usb0 {
+ status = "okay";
+ dr_mode = "host";
+};
+
+&usb1 {
+ status = "okay";
+ dr_mode = "host";
+};
+
+&davinci_mdio {
+ status = "okay";
+
+ phy0: ethernet-phy@0 {
+ reg = <1>;
+ };
+
+ phy1: ethernet-phy@1 {
+ reg = <2>;
+ };
+};
+
+&mac {
+ status = "okay";
+};
+
+&cpsw_emac0 {
+ phy-handle = <&phy0>;
+ dual_emac_res_vlan = <1>;
+ phy-mode = "mii";
+};
+
+&cpsw_emac1 {
+ phy-handle = <&phy1>;
+ dual_emac_res_vlan = <2>;
+ phy-mode = "mii";
+};
+
+&mmc1 {
+ u-boot,dm-spl;
+ vmmc-supply = <&vmmcsd_fixed>;
+ bus-width = <0x4>;
+ ti,non-removable;
+ ti,needs-special-hs-handling;
+ ti,vcc-aux-disable-is-sleep;
+ status = "okay";
+};
+
+&mmc2 {
+ u-boot,dm-spl;
+ vmmc-supply = <&vmmcsd_fixed>;
+ bus-width = <0x8>;
+ ti,non-removable;
+ ti,needs-special-hs-handling;
+ ti,vcc-aux-disable-is-sleep;
+ status = "okay";
+};
+
+&lcdc {
+ status = "disabled";
+};
+
+&elm {
+ status = "okay";
+};
+
+&sham {
+ status = "okay";
+};
+
+&aes {
+ status = "okay";
+};
+
+&gpio0 {
+ u-boot,dm-spl;
+ ti,no-reset-on-init;
+};
+
+&gpio1 {
+ u-boot,dm-spl;
+ ti,no-reset-on-init;
+};
+
+&gpio2 {
+ u-boot,dm-spl;
+ ti,no-reset-on-init;
+};
+
+&gpio3 {
+ u-boot,dm-spl;
+ ti,no-reset-on-init;
+};
+
+&wdt2 {
+ ti,no-reset-on-init;
+ ti,no-idle-on-init;
+};
+
+&tscadc {
+ status = "okay";
+ tsc {
+ ti,wires = <4>;
+ ti,x-plate-resistance = <200>;
+ ti,zx-cutoff-ratio = <40>;
+ ti,min_deviation = <60>;
+ ti,max_deviation = <600>;
+ ti,coordinate-readouts = <5>;
+ ti,wire-config = <0x00 0x11 0x22 0x33>;
+
+ bnr-buttons {
+ Home-Button {};
+ };
+ };
+
+ adc {
+ ti,adc-channels = <5 6 7>;
+ };
+};
+
+&timer6 { /* used for cpsw end device */
+ status = "okay";
+ ti,no-reset-on-init;
+ ti,no-idle-on-init;
+};
+
+&timer7 { /* used for cpsw end device */
+ status = "okay";
+ ti,no-reset-on-init;
+ ti,no-idle-on-init;
+};
+
+&wdt2 {
+ status = "okay";
+ ti,no-reset-on-init;
+ ti,no-idle-on-init;
+};
+
+&epwmss0 {
+ status = "okay";
+};
+
+&tscadc {
+ status = "okay";
+};
+
+&dcan0 {
+ status = "okay";
+};
+
+&dcan1 {
+ status = "okay";
+};
+
+&sham {
+ status = "disabled";
+};
+
+&aes {
+ status = "disabled";
+};
+
+&rng {
+ status = "disabled";
+};
void am33xx_spl_board_init(void)
{
+ int rc;
+
struct cm_perpll *const cmper = (struct cm_perpll *)CM_PER;
/*struct cm_wkuppll *const cmwkup = (struct cm_wkuppll *)CM_WKUP;*/
struct cm_dpll *const cmdpll = (struct cm_dpll *)CM_DPLL;
i2c_init(CONFIG_SYS_OMAP24_I2C_SPEED, CONFIG_SYS_OMAP24_I2C_SLAVE);
pmicsetup(0);
- gpio_direction_output(64+29, 1); /* switch NAND_RnB to GPMC_WAIT1 */
- gpio_direction_output(64+28, 1); /* switch MII2_CRS to GPMC_WAIT0 */
+ /* peripheral reset */
+ rc = gpio_request(64 + 29, "GPMC_WAIT1");
+ if (rc != 0)
+ printf("cannot request GPMC_WAIT1 GPIO!\n");
+ rc = gpio_direction_output(64 + 29, 1);
+ if (rc != 0)
+ printf("cannot set GPMC_WAIT1 GPIO!\n");
+
+ rc = gpio_request(64 + 28, "GPMC_WAIT0");
+ if (rc != 0)
+ printf("cannot request GPMC_WAIT0 GPIO!\n");
+ rc = gpio_direction_output(64 + 28, 1);
+ if (rc != 0)
+ printf("cannot set GPMC_WAIT0 GPIO!\n");
+
}
const struct dpll_params *get_dpll_ddr_params(void)
{
unsigned char bmode = 0;
ulong bootcount = 0;
+ int rc;
bootcount = bootcount_load() & 0xF;
- if (gpio_get_value(REPSWITCH) == 0 || bootcount == 12)
+ rc = gpio_request(REPSWITCH, "REPSWITCH");
+
+ if (rc != 0 || gpio_get_value(REPSWITCH) == 0 || bootcount == 12)
bmode = 12;
else if (bootcount > 0)
bmode = 0;
#include <asm/io.h>
#include <asm/gpio.h>
#include <i2c.h>
-#include <miiphy.h>
-#include <cpsw.h>
#include <power/tps65217.h>
#include <lcd.h>
#include "bur_common.h"
#include "../../../drivers/video/am335x-fb.h"
-static struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE;
-
DECLARE_GLOBAL_DATA_PTR;
/* --------------------------------------------------------------------------*/
}
#ifdef CONFIG_SPL_BUILD
+
+static struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE;
+
void pmicsetup(u32 mpupll)
{
int mpu_vdd;
#endif /* CONFIG_SPL_BUILD */
-#if (defined(CONFIG_DRIVER_TI_CPSW) && !defined(CONFIG_SPL_BUILD)) || \
- (defined(CONFIG_SPL_ETH_SUPPORT) && defined(CONFIG_SPL_BUILD))
-static void cpsw_control(int enabled)
-{
- /* VTP can be added here */
- return;
-}
-
-/* describing port offsets of TI's CPSW block */
-static struct cpsw_slave_data cpsw_slaves[] = {
- {
- .slave_reg_ofs = 0x208,
- .sliver_reg_ofs = 0xd80,
- .phy_addr = 1,
- },
- {
- .slave_reg_ofs = 0x308,
- .sliver_reg_ofs = 0xdc0,
- .phy_addr = 2,
- },
-};
-
-static struct cpsw_platform_data cpsw_data = {
- .mdio_base = CPSW_MDIO_BASE,
- .cpsw_base = CPSW_BASE,
- .mdio_div = 0xff,
- .channels = 8,
- .cpdma_reg_ofs = 0x800,
- .slaves = 1,
- .slave_data = cpsw_slaves,
- .ale_reg_ofs = 0xd00,
- .ale_entries = 1024,
- .host_port_reg_ofs = 0x108,
- .hw_stats_reg_ofs = 0x900,
- .bd_ram_ofs = 0x2000,
- .mac_control = (1 << 5),
- .control = cpsw_control,
- .host_port_num = 0,
- .version = CPSW_CTRL_VERSION_2,
-};
-#endif /* CONFIG_DRIVER_TI_CPSW, ... */
-
-#if defined(CONFIG_DRIVER_TI_CPSW) && !defined(CONFIG_SPL_BUILD)
-int board_eth_init(bd_t *bis)
-{
- int rv = 0;
- char mac_addr[6];
- const char *mac = 0;
- uint32_t mac_hi, mac_lo;
- /* try reading mac address from efuse */
- mac_lo = readl(&cdev->macid0l);
- mac_hi = readl(&cdev->macid0h);
- mac_addr[0] = mac_hi & 0xFF;
- mac_addr[1] = (mac_hi & 0xFF00) >> 8;
- mac_addr[2] = (mac_hi & 0xFF0000) >> 16;
- mac_addr[3] = (mac_hi & 0xFF000000) >> 24;
- mac_addr[4] = mac_lo & 0xFF;
- mac_addr[5] = (mac_lo & 0xFF00) >> 8;
-
- if (!env_get("ethaddr")) {
- if (!mac) {
- printf("<ethaddr> not set. validating E-fuse MAC ... ");
- if (is_valid_ethaddr((const u8 *)mac_addr))
- mac = (const char *)mac_addr;
- }
-
- if (mac) {
- printf("using: %pM on ", mac);
- eth_env_set_enetaddr("ethaddr", (const u8 *)mac);
- }
- }
- writel(MII_MODE_ENABLE, &cdev->miisel);
- cpsw_slaves[0].phy_if = PHY_INTERFACE_MODE_MII;
- cpsw_slaves[1].phy_if = PHY_INTERFACE_MODE_MII;
-
- rv = cpsw_register(&cpsw_data);
- if (rv < 0) {
- printf("Error %d registering CPSW switch\n", rv);
- return 0;
- }
- return rv;
-}
-#endif /* defined(CONFIG_DRIVER_TI_CPSW) && !defined(CONFIG_SPL_BUILD) */
-#if defined(CONFIG_MMC)
-int board_mmc_init(bd_t *bis)
-{
- int rc = 0;
-
- rc |= omap_mmc_init(0, 0, 0, -1, -1);
- rc |= omap_mmc_init(1, 0, 0, -1, -1);
-
- return rc;
-}
-#endif
int overwrite_console(void)
{
return 1;
CONFIG_SPL_GPIO_SUPPORT=y
CONFIG_SPL_LIBCOMMON_SUPPORT=y
CONFIG_SPL_LIBGENERIC_SUPPORT=y
+CONFIG_SYS_MALLOC_F_LEN=0x4000
CONFIG_AM33XX=y
CONFIG_TARGET_BRPPT1=y
CONFIG_SPL_MMC_SUPPORT=y
CONFIG_SPL_SERIAL_SUPPORT=y
+# CONFIG_SPL_NAND_SUPPORT is not set
CONFIG_SPL=y
+CONFIG_DEFAULT_DEVICE_TREE="am335x-brppt1-mmc"
+CONFIG_TPL_SYS_MALLOC_F_LEN=0x0
+# CONFIG_EXPERT is not set
+# CONFIG_FIT is not set
CONFIG_OF_BOARD_SETUP=y
-CONFIG_SYS_EXTRA_OPTIONS="SERIAL1,CONS_INDEX=1,EMMC_BOOT"
CONFIG_BOOTDELAY=0
CONFIG_USE_BOOTCOMMAND=y
CONFIG_BOOTCOMMAND="run b_default"
# CONFIG_DISPLAY_CPUINFO is not set
# CONFIG_DISPLAY_BOARDINFO is not set
CONFIG_ARCH_MISC_INIT=y
+CONFIG_SPL_SYS_MALLOC_SIMPLE=y
+CONFIG_SPL_SEPARATE_BSS=y
CONFIG_SPL_I2C_SUPPORT=y
-# CONFIG_SPL_NAND_SUPPORT is not set
CONFIG_SPL_POWER_SUPPORT=y
CONFIG_SPL_WATCHDOG_SUPPORT=y
CONFIG_SPL_YMODEM_SUPPORT=y
# CONFIG_CMD_FLASH is not set
CONFIG_CMD_GPIO=y
CONFIG_CMD_I2C=y
-# CONFIG_CMD_LOADB is not set
# CONFIG_CMD_LOADS is not set
CONFIG_CMD_MMC=y
+CONFIG_CMD_PART=y
CONFIG_CMD_USB=y
# CONFIG_CMD_ITEST is not set
-# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
# CONFIG_CMD_NFS is not set
+CONFIG_CMD_MII=y
CONFIG_CMD_PING=y
+CONFIG_CMD_BOOTCOUNT=y
+CONFIG_CMD_BKOPS_ENABLE=y
+CONFIG_CMD_CACHE=y
CONFIG_CMD_TIME=y
CONFIG_CMD_EXT4=y
CONFIG_CMD_EXT4_WRITE=y
CONFIG_CMD_FAT=y
CONFIG_CMD_FS_GENERIC=y
+# CONFIG_SPL_DOS_PARTITION is not set
+CONFIG_OF_CONTROL=y
+CONFIG_SPL_OF_CONTROL=y
+CONFIG_OF_SPL_REMOVE_PROPS="pinctrl-0 pinctrl-names clocks clock-names interrupt-parent interrupt-controller interrupt-cells dma-names dmas "
CONFIG_ENV_IS_IN_MMC=y
-CONFIG_NETCONSOLE=y
+CONFIG_NET_RANDOM_ETHADDR=y
+CONFIG_DM=y
+CONFIG_SPL_DM=y
+CONFIG_SPL_DM_SEQ_ALIAS=y
+# CONFIG_OF_TRANSLATE is not set
CONFIG_BOOTCOUNT_LIMIT=y
+CONFIG_DM_GPIO=y
+CONFIG_DM_I2C=y
+CONFIG_DM_I2C_COMPAT=y
+CONFIG_I2C_SET_DEFAULT_BUS_NUM=y
+CONFIG_MISC=y
+CONFIG_DM_MMC=y
CONFIG_MMC_OMAP_HS=y
+CONFIG_PHY_NATSEMI=y
+CONFIG_DM_ETH=y
CONFIG_DRIVER_TI_CPSW=y
+# CONFIG_NETDEVICES is not set
+CONFIG_DM_SERIAL=y
CONFIG_SYS_NS16550=y
CONFIG_USB=y
+CONFIG_DM_USB=y
CONFIG_USB_MUSB_HOST=y
+CONFIG_USB_MUSB_GADGET=y
+CONFIG_USB_MUSB_TI=y
CONFIG_USB_MUSB_DSPS=y
CONFIG_USB_STORAGE=y
+CONFIG_USB_GADGET=y
CONFIG_FAT_WRITE=y
-CONFIG_OF_LIBFDT=y
+CONFIG_LZO=y
+# CONFIG_OF_LIBFDT_OVERLAY is not set
+# CONFIG_EFI_LOADER is not set
CONFIG_SPL_GPIO_SUPPORT=y
CONFIG_SPL_LIBCOMMON_SUPPORT=y
CONFIG_SPL_LIBGENERIC_SUPPORT=y
+CONFIG_SYS_MALLOC_F_LEN=0x2000
CONFIG_AM33XX=y
CONFIG_TARGET_BRPPT1=y
CONFIG_SPL_SERIAL_SUPPORT=y
CONFIG_SPL=y
+CONFIG_DEFAULT_DEVICE_TREE="am335x-brppt1-nand"
+CONFIG_TPL_SYS_MALLOC_F_LEN=0x0
+# CONFIG_EXPERT is not set
+# CONFIG_FIT is not set
CONFIG_OF_BOARD_SETUP=y
-CONFIG_SYS_EXTRA_OPTIONS="SERIAL1,CONS_INDEX=1"
CONFIG_BOOTDELAY=0
CONFIG_USE_BOOTCOMMAND=y
CONFIG_BOOTCOMMAND="run b_default"
# CONFIG_DISPLAY_CPUINFO is not set
# CONFIG_DISPLAY_BOARDINFO is not set
CONFIG_ARCH_MISC_INIT=y
+CONFIG_SPL_SYS_MALLOC_SIMPLE=y
+CONFIG_SPL_SEPARATE_BSS=y
+# CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR is not set
CONFIG_SPL_I2C_SUPPORT=y
CONFIG_SPL_POWER_SUPPORT=y
CONFIG_SPL_WATCHDOG_SUPPORT=y
# CONFIG_CMD_FLASH is not set
CONFIG_CMD_GPIO=y
CONFIG_CMD_I2C=y
-# CONFIG_CMD_LOADB is not set
# CONFIG_CMD_LOADS is not set
CONFIG_CMD_NAND=y
+CONFIG_CMD_PART=y
CONFIG_CMD_USB=y
# CONFIG_CMD_ITEST is not set
-# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
# CONFIG_CMD_NFS is not set
+CONFIG_CMD_MII=y
CONFIG_CMD_PING=y
+CONFIG_CMD_BOOTCOUNT=y
+CONFIG_CMD_CACHE=y
CONFIG_CMD_TIME=y
CONFIG_CMD_EXT4=y
CONFIG_CMD_EXT4_WRITE=y
CONFIG_CMD_MTDPARTS=y
CONFIG_MTDIDS_DEFAULT="nand0=omap2-nand.0"
CONFIG_MTDPARTS_DEFAULT="mtdparts=omap2-nand.0:128k(MLO),128k(cfgscr),128k(dtb),128k(u-boot-env),512k(u-boot),4m(kernel),128m(rootfs),-(user)"
+# CONFIG_SPL_DOS_PARTITION is not set
+CONFIG_OF_CONTROL=y
+CONFIG_SPL_OF_CONTROL=y
+CONFIG_OF_SPL_REMOVE_PROPS="pinctrl-0 pinctrl-names clocks clock-names interrupt-parent interrupt-controller interrupt-cells dma-names dmas "
CONFIG_ENV_IS_IN_NAND=y
-CONFIG_NETCONSOLE=y
+CONFIG_NET_RANDOM_ETHADDR=y
+CONFIG_DM=y
+CONFIG_SPL_DM=y
+CONFIG_SPL_DM_SEQ_ALIAS=y
+# CONFIG_OF_TRANSLATE is not set
+CONFIG_BLK=y
CONFIG_BOOTCOUNT_LIMIT=y
+CONFIG_DM_GPIO=y
+CONFIG_DM_I2C=y
+CONFIG_DM_I2C_COMPAT=y
+CONFIG_I2C_SET_DEFAULT_BUS_NUM=y
+CONFIG_MISC=y
# CONFIG_MMC is not set
CONFIG_NAND=y
+CONFIG_SYS_NAND_U_BOOT_LOCATIONS=y
+CONFIG_SYS_NAND_U_BOOT_OFFS=0x80000
+CONFIG_PHY_NATSEMI=y
+CONFIG_DM_ETH=y
CONFIG_DRIVER_TI_CPSW=y
+# CONFIG_NETDEVICES is not set
+CONFIG_DM_SERIAL=y
CONFIG_SYS_NS16550=y
CONFIG_USB=y
+CONFIG_DM_USB=y
CONFIG_USB_MUSB_HOST=y
+CONFIG_USB_MUSB_GADGET=y
+CONFIG_USB_MUSB_TI=y
CONFIG_USB_MUSB_DSPS=y
CONFIG_USB_STORAGE=y
+CONFIG_USB_GADGET=y
CONFIG_FAT_WRITE=y
-CONFIG_OF_LIBFDT=y
+CONFIG_LZO=y
+# CONFIG_OF_LIBFDT_OVERLAY is not set
+# CONFIG_EFI_LOADER is not set
CONFIG_SPL_GPIO_SUPPORT=y
CONFIG_SPL_LIBCOMMON_SUPPORT=y
CONFIG_SPL_LIBGENERIC_SUPPORT=y
+CONFIG_SYS_MALLOC_F_LEN=0x4000
CONFIG_AM33XX=y
CONFIG_TARGET_BRPPT1=y
-CONFIG_SPL_MMC_SUPPORT=y
CONFIG_SPL_SERIAL_SUPPORT=y
CONFIG_SPL=y
CONFIG_SPL_SPI_FLASH_SUPPORT=y
CONFIG_SPL_SPI_SUPPORT=y
+CONFIG_DEFAULT_DEVICE_TREE="am335x-brppt1-spi"
+CONFIG_TPL_SYS_MALLOC_F_LEN=0x0
+# CONFIG_EXPERT is not set
+# CONFIG_FIT is not set
CONFIG_OF_BOARD_SETUP=y
-CONFIG_SYS_EXTRA_OPTIONS="SERIAL1,CONS_INDEX=1,SPI_BOOT,EMMC_BOOT"
CONFIG_SPI_BOOT=y
CONFIG_BOOTDELAY=0
CONFIG_USE_BOOTCOMMAND=y
# CONFIG_DISPLAY_CPUINFO is not set
# CONFIG_DISPLAY_BOARDINFO is not set
CONFIG_ARCH_MISC_INIT=y
+CONFIG_SPL_SYS_MALLOC_SIMPLE=y
+CONFIG_SPL_SEPARATE_BSS=y
+# CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR is not set
CONFIG_SPL_I2C_SUPPORT=y
# CONFIG_SPL_NAND_SUPPORT is not set
CONFIG_SPL_POWER_SUPPORT=y
# CONFIG_CMD_FLASH is not set
CONFIG_CMD_GPIO=y
CONFIG_CMD_I2C=y
-# CONFIG_CMD_LOADB is not set
# CONFIG_CMD_LOADS is not set
CONFIG_CMD_MMC=y
+CONFIG_CMD_PART=y
CONFIG_CMD_SF=y
-CONFIG_CMD_SPI=y
CONFIG_CMD_USB=y
# CONFIG_CMD_ITEST is not set
-# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
# CONFIG_CMD_NFS is not set
+CONFIG_CMD_MII=y
CONFIG_CMD_PING=y
+CONFIG_CMD_BOOTCOUNT=y
+CONFIG_CMD_BKOPS_ENABLE=y
+CONFIG_CMD_CACHE=y
CONFIG_CMD_TIME=y
CONFIG_CMD_EXT4=y
CONFIG_CMD_EXT4_WRITE=y
CONFIG_CMD_FAT=y
CONFIG_CMD_FS_GENERIC=y
-CONFIG_CMD_MTDPARTS=y
+# CONFIG_SPL_DOS_PARTITION is not set
+CONFIG_OF_CONTROL=y
+CONFIG_SPL_OF_CONTROL=y
+CONFIG_OF_SPL_REMOVE_PROPS="pinctrl-0 pinctrl-names clocks clock-names interrupt-parent interrupt-controller interrupt-cells dma-names dmas "
CONFIG_ENV_IS_IN_SPI_FLASH=y
-CONFIG_NETCONSOLE=y
+CONFIG_NET_RANDOM_ETHADDR=y
+CONFIG_DM=y
+CONFIG_SPL_DM=y
+CONFIG_SPL_DM_SEQ_ALIAS=y
+# CONFIG_OF_TRANSLATE is not set
CONFIG_BOOTCOUNT_LIMIT=y
+CONFIG_DM_GPIO=y
+CONFIG_DM_I2C=y
+CONFIG_DM_I2C_COMPAT=y
+CONFIG_I2C_SET_DEFAULT_BUS_NUM=y
+CONFIG_MISC=y
+CONFIG_DM_MMC=y
CONFIG_MMC_OMAP_HS=y
+CONFIG_DM_SPI_FLASH=y
CONFIG_SPI_FLASH=y
CONFIG_SPI_FLASH_STMICRO=y
+CONFIG_SPI_FLASH_WINBOND=y
# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set
+CONFIG_PHY_NATSEMI=y
+CONFIG_DM_ETH=y
CONFIG_DRIVER_TI_CPSW=y
+# CONFIG_NETDEVICES is not set
+CONFIG_DM_SERIAL=y
CONFIG_SYS_NS16550=y
CONFIG_SPI=y
+CONFIG_DM_SPI=y
CONFIG_OMAP3_SPI=y
CONFIG_USB=y
+CONFIG_DM_USB=y
CONFIG_USB_MUSB_HOST=y
+CONFIG_USB_MUSB_GADGET=y
+CONFIG_USB_MUSB_TI=y
CONFIG_USB_MUSB_DSPS=y
CONFIG_USB_STORAGE=y
+CONFIG_USB_GADGET=y
CONFIG_FAT_WRITE=y
-CONFIG_OF_LIBFDT=y
+CONFIG_LZO=y
+# CONFIG_OF_LIBFDT_OVERLAY is not set
+# CONFIG_EFI_LOADER is not set
#endif /* CONFIG_EMMC_BOOT */
/*
- * When we have SPI or NAND flash we expect to be making use of mtdparts,
+ * When we have NAND flash we expect to be making use of mtdparts,
* both for ease of use in U-Boot and for passing information on to
* the Linux kernel.
*/
-#if defined(CONFIG_SPI_BOOT) || defined(CONFIG_NAND)
+#if defined(CONFIG_NAND)
#define CONFIG_MTD_DEVICE /* Required for mtdparts */
-#endif /* CONFIG_SPI_BOOT, ... */
+#endif
#ifdef CONFIG_NAND
#define CONFIG_SPL_NAND_BASE
"b_tgts_pme=net usb0 mmc0 mmc1\0" \
"loaddev=mmc 1\0"
-#ifdef CONFIG_MMC
+#ifdef CONFIG_ENV_IS_IN_MMC
#define MMCTGTS \
MMCSPI_TGTS \
"cfgscr=mmc dev 1; mmc read ${cfgaddr} 200 80; source ${cfgaddr}\0"
#define CONFIG_SYS_NAND_ECCBYTES 14
#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000
#define CONFIG_NAND_OMAP_GPMC_WSCFG 1
#endif /* CONFIG_NAND */
/* USB configuration */
#define CONFIG_USB_MUSB_DISABLE_BULK_COMBINE_SPLIT
-#define CONFIG_AM335X_USB0
-#define CONFIG_AM335X_USB0_MODE MUSB_HOST
-#define CONFIG_AM335X_USB1
-#define CONFIG_AM335X_USB1_MODE MUSB_HOST
-#if defined(CONFIG_SPI_BOOT)
-/* McSPI IP block */
-#define CONFIG_SF_DEFAULT_SPEED 24000000
-
-#define CONFIG_SYS_SPI_U_BOOT_OFFS 0x20000
+#if defined(CONFIG_SPI)
+/* SPI Flash */
+#define CONFIG_SF_DEFAULT_SPEED 24000000
+#define CONFIG_SYS_SPI_U_BOOT_OFFS 0x40000
+/* Environment */
#define CONFIG_SYS_REDUNDAND_ENVIRONMENT
-#define CONFIG_ENV_SPI_MAX_HZ CONFIG_SF_DEFAULT_SPEED
-#define CONFIG_ENV_SECT_SIZE (4 << 10) /* 4 KB sectors */
-#define CONFIG_ENV_OFFSET (768 << 10) /* 768 KiB in */
-#define CONFIG_ENV_OFFSET_REDUND (896 << 10) /* 896 KiB in */
-
-#elif defined(CONFIG_EMMC_BOOT)
+#define CONFIG_ENV_SPI_MAX_HZ CONFIG_SF_DEFAULT_SPEED
+#define CONFIG_ENV_SECT_SIZE CONFIG_ENV_SIZE
+#define CONFIG_ENV_OFFSET 0x20000
+#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + \
+ CONFIG_ENV_SECT_SIZE)
+#elif defined(CONFIG_ENV_IS_IN_MMC)
#define CONFIG_SYS_MMC_ENV_DEV 1
#define CONFIG_SYS_MMC_ENV_PART 2
#define CONFIG_ENV_OFFSET 0x40000 /* TODO: Adresse definieren */
#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
#define CONFIG_SYS_REDUNDAND_ENVIRONMENT
-#elif defined(CONFIG_NAND)
+#elif defined(CONFIG_ENV_IS_IN_NAND)
/* No NAND env support in SPL */
#define CONFIG_ENV_OFFSET 0x60000
#define CONFIG_SYS_ENV_SECT_SIZE CONFIG_ENV_SIZE
#ifndef __BUR_AM335X_COMMON_H__
#define __BUR_AM335X_COMMON_H__
/* ------------------------------------------------------------------------- */
+
+/* legacy #defines for non DM bur-board */
+#ifndef CONFIG_DM
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE (-4)
+#define CONFIG_SYS_NS16550_CLK (48000000)
+#define CONFIG_SYS_NS16550_COM1 0x44e09000
+
+#define CONFIG_I2C
+#define CONFIG_SYS_I2C
+
+#endif /* CONFIG_DM */
+
#define CONFIG_MAX_RAM_BANK_SIZE (1024 << 20) /* 1GB */
/* Timer information */
#include <asm/arch/omap.h>
-/* NS16550 Configuration */
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE (-4)
-#define CONFIG_SYS_NS16550_CLK 48000000
-#define CONFIG_SYS_NS16550_COM1 0x44e09000 /* UART0 */
-
-/* Network defines */
-#define CONFIG_MII /* Required in net/eth.c */
-#define CONFIG_PHY_NATSEMI
-
/*
* SPL related defines. The Public RAM memory map the ROM defines the
* area between 0x402F0400 and 0x4030B800 as a download area and
#define CONFIG_SYS_INIT_SP_ADDR (NON_SECURE_SRAM_END - \
GENERATED_GBL_DATA_SIZE)
-/* I2C */
-#define CONFIG_SYS_I2C
-
/*
* Our platforms make use of SPL to initalize the hardware (primarily
* memory) enough for full U-Boot to be loaded. We also support Falcon
projects / platform / kernel / u-boot.git / commitdiff