This driver provides common support WCD934x audio codec and its
associated Pin Controller, Soundwire Controller and Audio codec.
+config MFD_ATC260X
+ tristate
+ select MFD_CORE
+ select REGMAP
+ select REGMAP_IRQ
+
+config MFD_ATC260X_I2C
+ tristate "Actions Semi ATC260x PMICs with I2C"
+ select MFD_ATC260X
+ select REGMAP_I2C
+ depends on I2C
+ help
+ Support for the Actions Semi ATC260x PMICs controlled via I2C.
+
+ This driver provides common support for accessing the ATC2603C
+ and ATC2609A chip variants, additional drivers must be enabled
+ in order to use the functionality of the device.
+
config MFD_KHADAS_MCU
tristate "Support for Khadas System control Microcontroller"
depends on I2C
obj-$(CONFIG_SGI_MFD_IOC3) += ioc3.o
obj-$(CONFIG_MFD_SIMPLE_MFD_I2C) += simple-mfd-i2c.o
obj-$(CONFIG_MFD_INTEL_M10_BMC) += intel-m10-bmc.o
+
+obj-$(CONFIG_MFD_ATC260X) += atc260x-core.o
+obj-$(CONFIG_MFD_ATC260X_I2C) += atc260x-i2c.o
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Core support for ATC260x PMICs
+ *
+ * Copyright (C) 2019 Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
+ * Copyright (C) 2020 Cristian Ciocaltea <cristian.ciocaltea@gmail.com>
+ */
+
+#include <linux/interrupt.h>
+#include <linux/mfd/atc260x/core.h>
+#include <linux/mfd/core.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/regmap.h>
+
+#define ATC260X_CHIP_REV_MAX 31
+
+struct atc260x_init_regs {
+ unsigned int cmu_devrst;
+ unsigned int cmu_devrst_ints;
+ unsigned int ints_msk;
+ unsigned int pad_en;
+ unsigned int pad_en_extirq;
+};
+
+static void regmap_lock_mutex(void *__mutex)
+{
+ struct mutex *mutex = __mutex;
+
+ /*
+ * Using regmap within an atomic context (e.g. accessing a PMIC when
+ * powering system down) is normally allowed only if the regmap type
+ * is MMIO and the regcache type is either REGCACHE_NONE or
+ * REGCACHE_FLAT. For slow buses like I2C and SPI, the regmap is
+ * internally protected by a mutex which is acquired non-atomically.
+ *
+ * Let's improve this by using a customized locking scheme inspired
+ * from I2C atomic transfer. See i2c_in_atomic_xfer_mode() for a
+ * starting point.
+ */
+ if (system_state > SYSTEM_RUNNING && irqs_disabled())
+ mutex_trylock(mutex);
+ else
+ mutex_lock(mutex);
+}
+
+static void regmap_unlock_mutex(void *__mutex)
+{
+ struct mutex *mutex = __mutex;
+
+ mutex_unlock(mutex);
+}
+
+static const struct regmap_config atc2603c_regmap_config = {
+ .reg_bits = 8,
+ .val_bits = 16,
+ .max_register = ATC2603C_SADDR,
+ .cache_type = REGCACHE_NONE,
+};
+
+static const struct regmap_config atc2609a_regmap_config = {
+ .reg_bits = 8,
+ .val_bits = 16,
+ .max_register = ATC2609A_SADDR,
+ .cache_type = REGCACHE_NONE,
+};
+
+static const struct regmap_irq atc2603c_regmap_irqs[] = {
+ REGMAP_IRQ_REG(ATC2603C_IRQ_AUDIO, 0, ATC2603C_INTS_MSK_AUDIO),
+ REGMAP_IRQ_REG(ATC2603C_IRQ_OV, 0, ATC2603C_INTS_MSK_OV),
+ REGMAP_IRQ_REG(ATC2603C_IRQ_OC, 0, ATC2603C_INTS_MSK_OC),
+ REGMAP_IRQ_REG(ATC2603C_IRQ_OT, 0, ATC2603C_INTS_MSK_OT),
+ REGMAP_IRQ_REG(ATC2603C_IRQ_UV, 0, ATC2603C_INTS_MSK_UV),
+ REGMAP_IRQ_REG(ATC2603C_IRQ_ALARM, 0, ATC2603C_INTS_MSK_ALARM),
+ REGMAP_IRQ_REG(ATC2603C_IRQ_ONOFF, 0, ATC2603C_INTS_MSK_ONOFF),
+ REGMAP_IRQ_REG(ATC2603C_IRQ_SGPIO, 0, ATC2603C_INTS_MSK_SGPIO),
+ REGMAP_IRQ_REG(ATC2603C_IRQ_IR, 0, ATC2603C_INTS_MSK_IR),
+ REGMAP_IRQ_REG(ATC2603C_IRQ_REMCON, 0, ATC2603C_INTS_MSK_REMCON),
+ REGMAP_IRQ_REG(ATC2603C_IRQ_POWER_IN, 0, ATC2603C_INTS_MSK_POWERIN),
+};
+
+static const struct regmap_irq atc2609a_regmap_irqs[] = {
+ REGMAP_IRQ_REG(ATC2609A_IRQ_AUDIO, 0, ATC2609A_INTS_MSK_AUDIO),
+ REGMAP_IRQ_REG(ATC2609A_IRQ_OV, 0, ATC2609A_INTS_MSK_OV),
+ REGMAP_IRQ_REG(ATC2609A_IRQ_OC, 0, ATC2609A_INTS_MSK_OC),
+ REGMAP_IRQ_REG(ATC2609A_IRQ_OT, 0, ATC2609A_INTS_MSK_OT),
+ REGMAP_IRQ_REG(ATC2609A_IRQ_UV, 0, ATC2609A_INTS_MSK_UV),
+ REGMAP_IRQ_REG(ATC2609A_IRQ_ALARM, 0, ATC2609A_INTS_MSK_ALARM),
+ REGMAP_IRQ_REG(ATC2609A_IRQ_ONOFF, 0, ATC2609A_INTS_MSK_ONOFF),
+ REGMAP_IRQ_REG(ATC2609A_IRQ_WKUP, 0, ATC2609A_INTS_MSK_WKUP),
+ REGMAP_IRQ_REG(ATC2609A_IRQ_IR, 0, ATC2609A_INTS_MSK_IR),
+ REGMAP_IRQ_REG(ATC2609A_IRQ_REMCON, 0, ATC2609A_INTS_MSK_REMCON),
+ REGMAP_IRQ_REG(ATC2609A_IRQ_POWER_IN, 0, ATC2609A_INTS_MSK_POWERIN),
+};
+
+static const struct regmap_irq_chip atc2603c_regmap_irq_chip = {
+ .name = "atc2603c",
+ .irqs = atc2603c_regmap_irqs,
+ .num_irqs = ARRAY_SIZE(atc2603c_regmap_irqs),
+ .num_regs = 1,
+ .status_base = ATC2603C_INTS_PD,
+ .mask_base = ATC2603C_INTS_MSK,
+ .mask_invert = true,
+};
+
+static const struct regmap_irq_chip atc2609a_regmap_irq_chip = {
+ .name = "atc2609a",
+ .irqs = atc2609a_regmap_irqs,
+ .num_irqs = ARRAY_SIZE(atc2609a_regmap_irqs),
+ .num_regs = 1,
+ .status_base = ATC2609A_INTS_PD,
+ .mask_base = ATC2609A_INTS_MSK,
+ .mask_invert = true,
+};
+
+static const struct resource atc2603c_onkey_resources[] = {
+ DEFINE_RES_IRQ(ATC2603C_IRQ_ONOFF),
+};
+
+static const struct resource atc2609a_onkey_resources[] = {
+ DEFINE_RES_IRQ(ATC2609A_IRQ_ONOFF),
+};
+
+static const struct mfd_cell atc2603c_mfd_cells[] = {
+ { .name = "atc260x-regulator" },
+ { .name = "atc260x-pwrc" },
+ {
+ .name = "atc260x-onkey",
+ .num_resources = ARRAY_SIZE(atc2603c_onkey_resources),
+ .resources = atc2603c_onkey_resources,
+ },
+};
+
+static const struct mfd_cell atc2609a_mfd_cells[] = {
+ { .name = "atc260x-regulator" },
+ { .name = "atc260x-pwrc" },
+ {
+ .name = "atc260x-onkey",
+ .num_resources = ARRAY_SIZE(atc2609a_onkey_resources),
+ .resources = atc2609a_onkey_resources,
+ },
+};
+
+static const struct atc260x_init_regs atc2603c_init_regs = {
+ .cmu_devrst = ATC2603C_CMU_DEVRST,
+ .cmu_devrst_ints = ATC2603C_CMU_DEVRST_INTS,
+ .ints_msk = ATC2603C_INTS_MSK,
+ .pad_en = ATC2603C_PAD_EN,
+ .pad_en_extirq = ATC2603C_PAD_EN_EXTIRQ,
+};
+
+static const struct atc260x_init_regs atc2609a_init_regs = {
+ .cmu_devrst = ATC2609A_CMU_DEVRST,
+ .cmu_devrst_ints = ATC2609A_CMU_DEVRST_INTS,
+ .ints_msk = ATC2609A_INTS_MSK,
+ .pad_en = ATC2609A_PAD_EN,
+ .pad_en_extirq = ATC2609A_PAD_EN_EXTIRQ,
+};
+
+static void atc260x_cmu_reset(struct atc260x *atc260x)
+{
+ const struct atc260x_init_regs *regs = atc260x->init_regs;
+
+ /* Assert reset */
+ regmap_update_bits(atc260x->regmap, regs->cmu_devrst,
+ regs->cmu_devrst_ints, ~regs->cmu_devrst_ints);
+
+ /* De-assert reset */
+ regmap_update_bits(atc260x->regmap, regs->cmu_devrst,
+ regs->cmu_devrst_ints, regs->cmu_devrst_ints);
+}
+
+static void atc260x_dev_init(struct atc260x *atc260x)
+{
+ const struct atc260x_init_regs *regs = atc260x->init_regs;
+
+ /* Initialize interrupt block */
+ atc260x_cmu_reset(atc260x);
+
+ /* Disable all interrupt sources */
+ regmap_write(atc260x->regmap, regs->ints_msk, 0);
+
+ /* Enable EXTIRQ pad */
+ regmap_update_bits(atc260x->regmap, regs->pad_en,
+ regs->pad_en_extirq, regs->pad_en_extirq);
+}
+
+/**
+ * atc260x_match_device(): Setup ATC260x variant related fields
+ *
+ * @atc260x: ATC260x device to setup (.dev field must be set)
+ * @regmap_cfg: regmap config associated with this ATC260x device
+ *
+ * This lets the ATC260x core configure the MFD cells and register maps
+ * for later use.
+ */
+int atc260x_match_device(struct atc260x *atc260x, struct regmap_config *regmap_cfg)
+{
+ struct device *dev = atc260x->dev;
+ const void *of_data;
+
+ of_data = of_device_get_match_data(dev);
+ if (!of_data)
+ return -ENODEV;
+
+ atc260x->ic_type = (unsigned long)of_data;
+
+ switch (atc260x->ic_type) {
+ case ATC2603C:
+ *regmap_cfg = atc2603c_regmap_config;
+ atc260x->regmap_irq_chip = &atc2603c_regmap_irq_chip;
+ atc260x->cells = atc2603c_mfd_cells;
+ atc260x->nr_cells = ARRAY_SIZE(atc2603c_mfd_cells);
+ atc260x->type_name = "atc2603c";
+ atc260x->rev_reg = ATC2603C_CHIP_VER;
+ atc260x->init_regs = &atc2603c_init_regs;
+ break;
+ case ATC2609A:
+ *regmap_cfg = atc2609a_regmap_config;
+ atc260x->regmap_irq_chip = &atc2609a_regmap_irq_chip;
+ atc260x->cells = atc2609a_mfd_cells;
+ atc260x->nr_cells = ARRAY_SIZE(atc2609a_mfd_cells);
+ atc260x->type_name = "atc2609a";
+ atc260x->rev_reg = ATC2609A_CHIP_VER;
+ atc260x->init_regs = &atc2609a_init_regs;
+ break;
+ default:
+ dev_err(dev, "Unsupported ATC260x device type: %u\n",
+ atc260x->ic_type);
+ return -EINVAL;
+ }
+
+ atc260x->regmap_mutex = devm_kzalloc(dev, sizeof(*atc260x->regmap_mutex),
+ GFP_KERNEL);
+ if (!atc260x->regmap_mutex)
+ return -ENOMEM;
+
+ mutex_init(atc260x->regmap_mutex);
+
+ regmap_cfg->lock = regmap_lock_mutex,
+ regmap_cfg->unlock = regmap_unlock_mutex,
+ regmap_cfg->lock_arg = atc260x->regmap_mutex;
+
+ return 0;
+}
+EXPORT_SYMBOL_GPL(atc260x_match_device);
+
+/**
+ * atc260x_device_probe(): Probe a configured ATC260x device
+ *
+ * @atc260x: ATC260x device to probe (must be configured)
+ *
+ * This function lets the ATC260x core register the ATC260x MFD devices
+ * and IRQCHIP. The ATC260x device passed in must be fully configured
+ * with atc260x_match_device, its IRQ set, and regmap created.
+ */
+int atc260x_device_probe(struct atc260x *atc260x)
+{
+ struct device *dev = atc260x->dev;
+ unsigned int chip_rev;
+ int ret;
+
+ if (!atc260x->irq) {
+ dev_err(dev, "No interrupt support\n");
+ return -EINVAL;
+ }
+
+ /* Initialize the hardware */
+ atc260x_dev_init(atc260x);
+
+ ret = regmap_read(atc260x->regmap, atc260x->rev_reg, &chip_rev);
+ if (ret) {
+ dev_err(dev, "Failed to get chip revision\n");
+ return ret;
+ }
+
+ if (chip_rev > ATC260X_CHIP_REV_MAX) {
+ dev_err(dev, "Unknown chip revision: %u\n", chip_rev);
+ return -EINVAL;
+ }
+
+ atc260x->ic_ver = __ffs(chip_rev + 1U);
+
+ dev_info(dev, "Detected chip type %s rev.%c\n",
+ atc260x->type_name, 'A' + atc260x->ic_ver);
+
+ ret = devm_regmap_add_irq_chip(dev, atc260x->regmap, atc260x->irq, IRQF_ONESHOT,
+ -1, atc260x->regmap_irq_chip, &atc260x->irq_data);
+ if (ret) {
+ dev_err(dev, "Failed to add IRQ chip: %d\n", ret);
+ return ret;
+ }
+
+ ret = devm_mfd_add_devices(dev, PLATFORM_DEVID_NONE,
+ atc260x->cells, atc260x->nr_cells, NULL, 0,
+ regmap_irq_get_domain(atc260x->irq_data));
+ if (ret) {
+ dev_err(dev, "Failed to add child devices: %d\n", ret);
+ regmap_del_irq_chip(atc260x->irq, atc260x->irq_data);
+ }
+
+ return ret;
+}
+EXPORT_SYMBOL_GPL(atc260x_device_probe);
+
+MODULE_DESCRIPTION("ATC260x PMICs Core support");
+MODULE_AUTHOR("Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>");
+MODULE_AUTHOR("Cristian Ciocaltea <cristian.ciocaltea@gmail.com>");
+MODULE_LICENSE("GPL");
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * I2C bus interface for ATC260x PMICs
+ *
+ * Copyright (C) 2019 Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
+ * Copyright (C) 2020 Cristian Ciocaltea <cristian.ciocaltea@gmail.com>
+ */
+
+#include <linux/i2c.h>
+#include <linux/mfd/atc260x/core.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/regmap.h>
+
+static int atc260x_i2c_probe(struct i2c_client *client,
+ const struct i2c_device_id *id)
+{
+ struct atc260x *atc260x;
+ struct regmap_config regmap_cfg;
+ int ret;
+
+ atc260x = devm_kzalloc(&client->dev, sizeof(*atc260x), GFP_KERNEL);
+ if (!atc260x)
+ return -ENOMEM;
+
+ atc260x->dev = &client->dev;
+ atc260x->irq = client->irq;
+
+ ret = atc260x_match_device(atc260x, ®map_cfg);
+ if (ret)
+ return ret;
+
+ i2c_set_clientdata(client, atc260x);
+
+ atc260x->regmap = devm_regmap_init_i2c(client, ®map_cfg);
+ if (IS_ERR(atc260x->regmap)) {
+ ret = PTR_ERR(atc260x->regmap);
+ dev_err(&client->dev, "failed to init regmap: %d\n", ret);
+ return ret;
+ }
+
+ return atc260x_device_probe(atc260x);
+}
+
+const struct of_device_id atc260x_i2c_of_match[] = {
+ { .compatible = "actions,atc2603c", .data = (void *)ATC2603C },
+ { .compatible = "actions,atc2609a", .data = (void *)ATC2609A },
+ { }
+};
+MODULE_DEVICE_TABLE(of, atc260x_i2c_of_match);
+
+static struct i2c_driver atc260x_i2c_driver = {
+ .driver = {
+ .name = "atc260x",
+ .of_match_table = of_match_ptr(atc260x_i2c_of_match),
+ },
+ .probe = atc260x_i2c_probe,
+};
+module_i2c_driver(atc260x_i2c_driver);
+
+MODULE_DESCRIPTION("ATC260x PMICs I2C bus interface");
+MODULE_AUTHOR("Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>");
+MODULE_AUTHOR("Cristian Ciocaltea <cristian.ciocaltea@gmail.com>");
+MODULE_LICENSE("GPL");
--- /dev/null
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * ATC2603C PMIC register definitions
+ *
+ * Copyright (C) 2020 Cristian Ciocaltea <cristian.ciocaltea@gmail.com>
+ */
+
+#ifndef __LINUX_MFD_ATC260X_ATC2603C_H
+#define __LINUX_MFD_ATC260X_ATC2603C_H
+
+enum atc2603c_irq_def {
+ ATC2603C_IRQ_AUDIO = 0,
+ ATC2603C_IRQ_OV,
+ ATC2603C_IRQ_OC,
+ ATC2603C_IRQ_OT,
+ ATC2603C_IRQ_UV,
+ ATC2603C_IRQ_ALARM,
+ ATC2603C_IRQ_ONOFF,
+ ATC2603C_IRQ_SGPIO,
+ ATC2603C_IRQ_IR,
+ ATC2603C_IRQ_REMCON,
+ ATC2603C_IRQ_POWER_IN,
+};
+
+/* PMU Registers */
+#define ATC2603C_PMU_SYS_CTL0 0x00
+#define ATC2603C_PMU_SYS_CTL1 0x01
+#define ATC2603C_PMU_SYS_CTL2 0x02
+#define ATC2603C_PMU_SYS_CTL3 0x03
+#define ATC2603C_PMU_SYS_CTL4 0x04
+#define ATC2603C_PMU_SYS_CTL5 0x05
+#define ATC2603C_PMU_SYS_CTL6 0x06
+#define ATC2603C_PMU_SYS_CTL7 0x07
+#define ATC2603C_PMU_SYS_CTL8 0x08
+#define ATC2603C_PMU_SYS_CTL9 0x09
+#define ATC2603C_PMU_BAT_CTL0 0x0A
+#define ATC2603C_PMU_BAT_CTL1 0x0B
+#define ATC2603C_PMU_VBUS_CTL0 0x0C
+#define ATC2603C_PMU_VBUS_CTL1 0x0D
+#define ATC2603C_PMU_WALL_CTL0 0x0E
+#define ATC2603C_PMU_WALL_CTL1 0x0F
+#define ATC2603C_PMU_SYS_PENDING 0x10
+#define ATC2603C_PMU_DC1_CTL0 0x11
+#define ATC2603C_PMU_DC1_CTL1 0x12 // Undocumented
+#define ATC2603C_PMU_DC1_CTL2 0x13 // Undocumented
+#define ATC2603C_PMU_DC2_CTL0 0x14
+#define ATC2603C_PMU_DC2_CTL1 0x15 // Undocumented
+#define ATC2603C_PMU_DC2_CTL2 0x16 // Undocumented
+#define ATC2603C_PMU_DC3_CTL0 0x17
+#define ATC2603C_PMU_DC3_CTL1 0x18 // Undocumented
+#define ATC2603C_PMU_DC3_CTL2 0x19 // Undocumented
+#define ATC2603C_PMU_DC4_CTL0 0x1A // Undocumented
+#define ATC2603C_PMU_DC4_CTL1 0x1B // Undocumented
+#define ATC2603C_PMU_DC5_CTL0 0x1C // Undocumented
+#define ATC2603C_PMU_DC5_CTL1 0x1D // Undocumented
+#define ATC2603C_PMU_LDO1_CTL 0x1E
+#define ATC2603C_PMU_LDO2_CTL 0x1F
+#define ATC2603C_PMU_LDO3_CTL 0x20
+#define ATC2603C_PMU_LDO4_CTL 0x21 // Undocumented
+#define ATC2603C_PMU_LDO5_CTL 0x22
+#define ATC2603C_PMU_LDO6_CTL 0x23
+#define ATC2603C_PMU_LDO7_CTL 0x24
+#define ATC2603C_PMU_LDO8_CTL 0x25 // Undocumented
+#define ATC2603C_PMU_LDO9_CTL 0x26 // Undocumented
+#define ATC2603C_PMU_LDO10_CTL 0x27 // Undocumented
+#define ATC2603C_PMU_LDO11_CTL 0x28
+#define ATC2603C_PMU_SWITCH_CTL 0x29
+#define ATC2603C_PMU_OV_CTL0 0x2A
+#define ATC2603C_PMU_OV_CTL1 0x2B
+#define ATC2603C_PMU_OV_STATUS 0x2C
+#define ATC2603C_PMU_OV_EN 0x2D
+#define ATC2603C_PMU_OV_INT_EN 0x2E
+#define ATC2603C_PMU_OC_CTL 0x2F
+#define ATC2603C_PMU_OC_STATUS 0x30
+#define ATC2603C_PMU_OC_EN 0x31
+#define ATC2603C_PMU_OC_INT_EN 0x32
+#define ATC2603C_PMU_UV_CTL0 0x33
+#define ATC2603C_PMU_UV_CTL1 0x34
+#define ATC2603C_PMU_UV_STATUS 0x35
+#define ATC2603C_PMU_UV_EN 0x36
+#define ATC2603C_PMU_UV_INT_EN 0x37
+#define ATC2603C_PMU_OT_CTL 0x38
+#define ATC2603C_PMU_CHARGER_CTL0 0x39
+#define ATC2603C_PMU_CHARGER_CTL1 0x3A
+#define ATC2603C_PMU_CHARGER_CTL2 0x3B
+#define ATC2603C_PMU_BAKCHARGER_CTL 0x3C // Undocumented
+#define ATC2603C_PMU_APDS_CTL 0x3D
+#define ATC2603C_PMU_AUXADC_CTL0 0x3E
+#define ATC2603C_PMU_AUXADC_CTL1 0x3F
+#define ATC2603C_PMU_BATVADC 0x40
+#define ATC2603C_PMU_BATIADC 0x41
+#define ATC2603C_PMU_WALLVADC 0x42
+#define ATC2603C_PMU_WALLIADC 0x43
+#define ATC2603C_PMU_VBUSVADC 0x44
+#define ATC2603C_PMU_VBUSIADC 0x45
+#define ATC2603C_PMU_SYSPWRADC 0x46
+#define ATC2603C_PMU_REMCONADC 0x47
+#define ATC2603C_PMU_SVCCADC 0x48
+#define ATC2603C_PMU_CHGIADC 0x49
+#define ATC2603C_PMU_IREFADC 0x4A
+#define ATC2603C_PMU_BAKBATADC 0x4B
+#define ATC2603C_PMU_ICTEMPADC 0x4C
+#define ATC2603C_PMU_AUXADC0 0x4D
+#define ATC2603C_PMU_AUXADC1 0x4E
+#define ATC2603C_PMU_AUXADC2 0x4F
+#define ATC2603C_PMU_ICMADC 0x50
+#define ATC2603C_PMU_BDG_CTL 0x51 // Undocumented
+#define ATC2603C_RTC_CTL 0x52
+#define ATC2603C_RTC_MSALM 0x53
+#define ATC2603C_RTC_HALM 0x54
+#define ATC2603C_RTC_YMDALM 0x55
+#define ATC2603C_RTC_MS 0x56
+#define ATC2603C_RTC_H 0x57
+#define ATC2603C_RTC_DC 0x58
+#define ATC2603C_RTC_YMD 0x59
+#define ATC2603C_EFUSE_DAT 0x5A // Undocumented
+#define ATC2603C_EFUSECRTL1 0x5B // Undocumented
+#define ATC2603C_EFUSECRTL2 0x5C // Undocumented
+#define ATC2603C_PMU_FW_USE0 0x5D // Undocumented
+#define ATC2603C_PMU_FW_USE1 0x5E // Undocumented
+#define ATC2603C_PMU_FW_USE2 0x5F // Undocumented
+#define ATC2603C_PMU_FW_USE3 0x60 // Undocumented
+#define ATC2603C_PMU_FW_USE4 0x61 // Undocumented
+#define ATC2603C_PMU_ABNORMAL_STATUS 0x62
+#define ATC2603C_PMU_WALL_APDS_CTL 0x63
+#define ATC2603C_PMU_REMCON_CTL0 0x64
+#define ATC2603C_PMU_REMCON_CTL1 0x65
+#define ATC2603C_PMU_MUX_CTL0 0x66
+#define ATC2603C_PMU_SGPIO_CTL0 0x67
+#define ATC2603C_PMU_SGPIO_CTL1 0x68
+#define ATC2603C_PMU_SGPIO_CTL2 0x69
+#define ATC2603C_PMU_SGPIO_CTL3 0x6A
+#define ATC2603C_PMU_SGPIO_CTL4 0x6B
+#define ATC2603C_PWMCLK_CTL 0x6C
+#define ATC2603C_PWM0_CTL 0x6D
+#define ATC2603C_PWM1_CTL 0x6E
+#define ATC2603C_PMU_ADC_DBG0 0x70
+#define ATC2603C_PMU_ADC_DBG1 0x71
+#define ATC2603C_PMU_ADC_DBG2 0x72
+#define ATC2603C_PMU_ADC_DBG3 0x73
+#define ATC2603C_PMU_ADC_DBG4 0x74
+#define ATC2603C_IRC_CTL 0x80
+#define ATC2603C_IRC_STAT 0x81
+#define ATC2603C_IRC_CC 0x82
+#define ATC2603C_IRC_KDC 0x83
+#define ATC2603C_IRC_WK 0x84
+#define ATC2603C_IRC_RCC 0x85
+#define ATC2603C_IRC_FILTER 0x86
+
+/* AUDIO_OUT Registers */
+#define ATC2603C_AUDIOINOUT_CTL 0xA0
+#define ATC2603C_AUDIO_DEBUGOUTCTL 0xA1
+#define ATC2603C_DAC_DIGITALCTL 0xA2
+#define ATC2603C_DAC_VOLUMECTL0 0xA3
+#define ATC2603C_DAC_ANALOG0 0xA4
+#define ATC2603C_DAC_ANALOG1 0xA5
+#define ATC2603C_DAC_ANALOG2 0xA6
+#define ATC2603C_DAC_ANALOG3 0xA7
+
+/* AUDIO_IN Registers */
+#define ATC2603C_ADC_DIGITALCTL 0xA8
+#define ATC2603C_ADC_HPFCTL 0xA9
+#define ATC2603C_ADC_CTL 0xAA
+#define ATC2603C_AGC_CTL0 0xAB
+#define ATC2603C_AGC_CTL1 0xAC // Undocumented
+#define ATC2603C_AGC_CTL2 0xAD
+#define ATC2603C_ADC_ANALOG0 0xAE
+#define ATC2603C_ADC_ANALOG1 0xAF
+
+/* PCM_IF Registers */
+#define ATC2603C_PCM0_CTL 0xB0 // Undocumented
+#define ATC2603C_PCM1_CTL 0xB1 // Undocumented
+#define ATC2603C_PCM2_CTL 0xB2 // Undocumented
+#define ATC2603C_PCMIF_CTL 0xB3 // Undocumented
+
+/* CMU_CONTROL Registers */
+#define ATC2603C_CMU_DEVRST 0xC1 // Undocumented
+
+/* INTS Registers */
+#define ATC2603C_INTS_PD 0xC8
+#define ATC2603C_INTS_MSK 0xC9
+
+/* MFP Registers */
+#define ATC2603C_MFP_CTL 0xD0
+#define ATC2603C_PAD_VSEL 0xD1 // Undocumented
+#define ATC2603C_GPIO_OUTEN 0xD2
+#define ATC2603C_GPIO_INEN 0xD3
+#define ATC2603C_GPIO_DAT 0xD4
+#define ATC2603C_PAD_DRV 0xD5
+#define ATC2603C_PAD_EN 0xD6
+#define ATC2603C_DEBUG_SEL 0xD7 // Undocumented
+#define ATC2603C_DEBUG_IE 0xD8 // Undocumented
+#define ATC2603C_DEBUG_OE 0xD9 // Undocumented
+#define ATC2603C_BIST_START 0x0A // Undocumented
+#define ATC2603C_BIST_RESULT 0x0B // Undocumented
+#define ATC2603C_CHIP_VER 0xDC
+
+/* TWSI Registers */
+#define ATC2603C_SADDR 0xFF
+
+/* PMU_SYS_CTL0 Register Mask Bits */
+#define ATC2603C_PMU_SYS_CTL0_IR_WK_EN BIT(5)
+#define ATC2603C_PMU_SYS_CTL0_RESET_WK_EN BIT(6)
+#define ATC2603C_PMU_SYS_CTL0_HDSW_WK_EN BIT(7)
+#define ATC2603C_PMU_SYS_CTL0_ALARM_WK_EN BIT(8)
+#define ATC2603C_PMU_SYS_CTL0_REM_CON_WK_EN BIT(9)
+#define ATC2603C_PMU_SYS_CTL0_RESTART_EN BIT(10)
+#define ATC2603C_PMU_SYS_CTL0_SGPIOIRQ_WK_EN BIT(11)
+#define ATC2603C_PMU_SYS_CTL0_ONOFF_SHORT_WK_EN BIT(12)
+#define ATC2603C_PMU_SYS_CTL0_ONOFF_LONG_WK_EN BIT(13)
+#define ATC2603C_PMU_SYS_CTL0_WALL_WK_EN BIT(14)
+#define ATC2603C_PMU_SYS_CTL0_USB_WK_EN BIT(15)
+#define ATC2603C_PMU_SYS_CTL0_WK_ALL (GENMASK(15, 5) & (~BIT(10)))
+
+/* PMU_SYS_CTL1 Register Mask Bits */
+#define ATC2603C_PMU_SYS_CTL1_EN_S1 BIT(0)
+#define ATC2603C_PMU_SYS_CTL1_LB_S4_EN BIT(2)
+#define ATC2603C_PMU_SYS_CTL1_LB_S4 GENMASK(4, 3)
+#define ATC2603C_PMU_SYS_CTL1_LB_S4_3_1V BIT(4)
+#define ATC2603C_PMU_SYS_CTL1_IR_WK_FLAG BIT(5)
+#define ATC2603C_PMU_SYS_CTL1_RESET_WK_FLAG BIT(6)
+#define ATC2603C_PMU_SYS_CTL1_HDSW_WK_FLAG BIT(7)
+#define ATC2603C_PMU_SYS_CTL1_ALARM_WK_FLAG BIT(8)
+#define ATC2603C_PMU_SYS_CTL1_REM_CON_WK_FLAG BIT(9)
+#define ATC2603C_PMU_SYS_CTL1_ONOFF_PRESS_RESET_IRQ_PD BIT(10)
+#define ATC2603C_PMU_SYS_CTL1_SGPIOIRQ_WK_FLAG BIT(11)
+#define ATC2603C_PMU_SYS_CTL1_ONOFF_SHORT_WK_FLAG BIT(12)
+#define ATC2603C_PMU_SYS_CTL1_ONOFF_LONG_WK_FLAG BIT(13)
+#define ATC2603C_PMU_SYS_CTL1_WALL_WK_FLAG BIT(14)
+#define ATC2603C_PMU_SYS_CTL1_USB_WK_FLAG BIT(15)
+
+/* PMU_SYS_CTL2 Register Mask Bits */
+#define ATC2603C_PMU_SYS_CTL2_PMU_A_EN BIT(0)
+#define ATC2603C_PMU_SYS_CTL2_ONOFF_PRESS_INT_EN BIT(1)
+#define ATC2603C_PMU_SYS_CTL2_ONOFF_PRESS_PD BIT(2)
+#define ATC2603C_PMU_SYS_CTL2_S2TIMER GENMASK(5, 3)
+#define ATC2603C_PMU_SYS_CTL2_S2_TIMER_EN BIT(6)
+#define ATC2603C_PMU_SYS_CTL2_ONOFF_RESET_TIME_SEL GENMASK(8, 7)
+#define ATC2603C_PMU_SYS_CTL2_ONOFF_PRESS_RESET_EN BIT(9)
+#define ATC2603C_PMU_SYS_CTL2_ONOFF_PRESS_TIME GENMASK(11, 10)
+#define ATC2603C_PMU_SYS_CTL2_ONOFF_INT_EN BIT(12)
+#define ATC2603C_PMU_SYS_CTL2_ONOFF_LONG_PRESS BIT(13)
+#define ATC2603C_PMU_SYS_CTL2_ONOFF_SHORT_PRESS BIT(14)
+#define ATC2603C_PMU_SYS_CTL2_ONOFF_PRESS BIT(15)
+
+/* PMU_SYS_CTL3 Register Mask Bits */
+#define ATC2603C_PMU_SYS_CTL3_S2S3TOS1_TIMER GENMASK(8, 7)
+#define ATC2603C_PMU_SYS_CTL3_S2S3TOS1_TIMER_EN BIT(9)
+#define ATC2603C_PMU_SYS_CTL3_S3_TIMER GENMASK(12, 10)
+#define ATC2603C_PMU_SYS_CTL3_S3_TIMER_EN BIT(13)
+#define ATC2603C_PMU_SYS_CTL3_EN_S3 BIT(14)
+#define ATC2603C_PMU_SYS_CTL3_EN_S2 BIT(15)
+
+/* PMU_SYS_CTL5 Register Mask Bits */
+#define ATC2603C_PMU_SYS_CTL5_WALLWKDTEN BIT(7)
+#define ATC2603C_PMU_SYS_CTL5_VBUSWKDTEN BIT(8)
+#define ATC2603C_PMU_SYS_CTL5_REMCON_DECT_EN BIT(9)
+#define ATC2603C_PMU_SYS_CTL5_ONOFF_8S_SEL BIT(10)
+
+/* INTS_MSK Register Mask Bits */
+#define ATC2603C_INTS_MSK_AUDIO BIT(0)
+#define ATC2603C_INTS_MSK_OV BIT(1)
+#define ATC2603C_INTS_MSK_OC BIT(2)
+#define ATC2603C_INTS_MSK_OT BIT(3)
+#define ATC2603C_INTS_MSK_UV BIT(4)
+#define ATC2603C_INTS_MSK_ALARM BIT(5)
+#define ATC2603C_INTS_MSK_ONOFF BIT(6)
+#define ATC2603C_INTS_MSK_SGPIO BIT(7)
+#define ATC2603C_INTS_MSK_IR BIT(8)
+#define ATC2603C_INTS_MSK_REMCON BIT(9)
+#define ATC2603C_INTS_MSK_POWERIN BIT(10)
+
+/* CMU_DEVRST Register Mask Bits */
+#define ATC2603C_CMU_DEVRST_MFP BIT(1)
+#define ATC2603C_CMU_DEVRST_INTS BIT(2)
+#define ATC2603C_CMU_DEVRST_AUDIO BIT(4)
+
+/* PAD_EN Register Mask Bits */
+#define ATC2603C_PAD_EN_EXTIRQ BIT(0)
+
+#endif /* __LINUX_MFD_ATC260X_ATC2603C_H */
--- /dev/null
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * ATC2609A PMIC register definitions
+ *
+ * Copyright (C) 2019 Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
+ */
+
+#ifndef __LINUX_MFD_ATC260X_ATC2609A_H
+#define __LINUX_MFD_ATC260X_ATC2609A_H
+
+enum atc2609a_irq_def {
+ ATC2609A_IRQ_AUDIO = 0,
+ ATC2609A_IRQ_OV,
+ ATC2609A_IRQ_OC,
+ ATC2609A_IRQ_OT,
+ ATC2609A_IRQ_UV,
+ ATC2609A_IRQ_ALARM,
+ ATC2609A_IRQ_ONOFF,
+ ATC2609A_IRQ_WKUP,
+ ATC2609A_IRQ_IR,
+ ATC2609A_IRQ_REMCON,
+ ATC2609A_IRQ_POWER_IN,
+};
+
+/* PMU Registers */
+#define ATC2609A_PMU_SYS_CTL0 0x00
+#define ATC2609A_PMU_SYS_CTL1 0x01
+#define ATC2609A_PMU_SYS_CTL2 0x02
+#define ATC2609A_PMU_SYS_CTL3 0x03
+#define ATC2609A_PMU_SYS_CTL4 0x04
+#define ATC2609A_PMU_SYS_CTL5 0x05
+#define ATC2609A_PMU_SYS_CTL6 0x06
+#define ATC2609A_PMU_SYS_CTL7 0x07
+#define ATC2609A_PMU_SYS_CTL8 0x08
+#define ATC2609A_PMU_SYS_CTL9 0x09
+#define ATC2609A_PMU_BAT_CTL0 0x0A
+#define ATC2609A_PMU_BAT_CTL1 0x0B
+#define ATC2609A_PMU_VBUS_CTL0 0x0C
+#define ATC2609A_PMU_VBUS_CTL1 0x0D
+#define ATC2609A_PMU_WALL_CTL0 0x0E
+#define ATC2609A_PMU_WALL_CTL1 0x0F
+#define ATC2609A_PMU_SYS_PENDING 0x10
+#define ATC2609A_PMU_APDS_CTL0 0x11
+#define ATC2609A_PMU_APDS_CTL1 0x12
+#define ATC2609A_PMU_APDS_CTL2 0x13
+#define ATC2609A_PMU_CHARGER_CTL 0x14
+#define ATC2609A_PMU_BAKCHARGER_CTL 0x15
+#define ATC2609A_PMU_SWCHG_CTL0 0x16
+#define ATC2609A_PMU_SWCHG_CTL1 0x17
+#define ATC2609A_PMU_SWCHG_CTL2 0x18
+#define ATC2609A_PMU_SWCHG_CTL3 0x19
+#define ATC2609A_PMU_SWCHG_CTL4 0x1A
+#define ATC2609A_PMU_DC_OSC 0x1B
+#define ATC2609A_PMU_DC0_CTL0 0x1C
+#define ATC2609A_PMU_DC0_CTL1 0x1D
+#define ATC2609A_PMU_DC0_CTL2 0x1E
+#define ATC2609A_PMU_DC0_CTL3 0x1F
+#define ATC2609A_PMU_DC0_CTL4 0x20
+#define ATC2609A_PMU_DC0_CTL5 0x21
+#define ATC2609A_PMU_DC0_CTL6 0x22
+#define ATC2609A_PMU_DC1_CTL0 0x23
+#define ATC2609A_PMU_DC1_CTL1 0x24
+#define ATC2609A_PMU_DC1_CTL2 0x25
+#define ATC2609A_PMU_DC1_CTL3 0x26
+#define ATC2609A_PMU_DC1_CTL4 0x27
+#define ATC2609A_PMU_DC1_CTL5 0x28
+#define ATC2609A_PMU_DC1_CTL6 0x29
+#define ATC2609A_PMU_DC2_CTL0 0x2A
+#define ATC2609A_PMU_DC2_CTL1 0x2B
+#define ATC2609A_PMU_DC2_CTL2 0x2C
+#define ATC2609A_PMU_DC2_CTL3 0x2D
+#define ATC2609A_PMU_DC2_CTL4 0x2E
+#define ATC2609A_PMU_DC2_CTL5 0x2F
+#define ATC2609A_PMU_DC2_CTL6 0x30
+#define ATC2609A_PMU_DC3_CTL0 0x31
+#define ATC2609A_PMU_DC3_CTL1 0x32
+#define ATC2609A_PMU_DC3_CTL2 0x33
+#define ATC2609A_PMU_DC3_CTL3 0x34
+#define ATC2609A_PMU_DC3_CTL4 0x35
+#define ATC2609A_PMU_DC3_CTL5 0x36
+#define ATC2609A_PMU_DC3_CTL6 0x37
+#define ATC2609A_PMU_DC_ZR 0x38
+#define ATC2609A_PMU_LDO0_CTL0 0x39
+#define ATC2609A_PMU_LDO0_CTL1 0x3A
+#define ATC2609A_PMU_LDO1_CTL0 0x3B
+#define ATC2609A_PMU_LDO1_CTL1 0x3C
+#define ATC2609A_PMU_LDO2_CTL0 0x3D
+#define ATC2609A_PMU_LDO2_CTL1 0x3E
+#define ATC2609A_PMU_LDO3_CTL0 0x3F
+#define ATC2609A_PMU_LDO3_CTL1 0x40
+#define ATC2609A_PMU_LDO4_CTL0 0x41
+#define ATC2609A_PMU_LDO4_CTL1 0x42
+#define ATC2609A_PMU_LDO5_CTL0 0x43
+#define ATC2609A_PMU_LDO5_CTL1 0x44
+#define ATC2609A_PMU_LDO6_CTL0 0x45
+#define ATC2609A_PMU_LDO6_CTL1 0x46
+#define ATC2609A_PMU_LDO7_CTL0 0x47
+#define ATC2609A_PMU_LDO7_CTL1 0x48
+#define ATC2609A_PMU_LDO8_CTL0 0x49
+#define ATC2609A_PMU_LDO8_CTL1 0x4A
+#define ATC2609A_PMU_LDO9_CTL 0x4B
+#define ATC2609A_PMU_OV_INT_EN 0x4C
+#define ATC2609A_PMU_OV_STATUS 0x4D
+#define ATC2609A_PMU_UV_INT_EN 0x4E
+#define ATC2609A_PMU_UV_STATUS 0x4F
+#define ATC2609A_PMU_OC_INT_EN 0x50
+#define ATC2609A_PMU_OC_STATUS 0x51
+#define ATC2609A_PMU_OT_CTL 0x52
+#define ATC2609A_PMU_CM_CTL0 0x53
+#define ATC2609A_PMU_FW_USE0 0x54
+#define ATC2609A_PMU_FW_USE1 0x55
+#define ATC2609A_PMU_ADC12B_I 0x56
+#define ATC2609A_PMU_ADC12B_V 0x57
+#define ATC2609A_PMU_ADC12B_DUMMY 0x58
+#define ATC2609A_PMU_AUXADC_CTL0 0x59
+#define ATC2609A_PMU_AUXADC_CTL1 0x5A
+#define ATC2609A_PMU_BATVADC 0x5B
+#define ATC2609A_PMU_BATIADC 0x5C
+#define ATC2609A_PMU_WALLVADC 0x5D
+#define ATC2609A_PMU_WALLIADC 0x5E
+#define ATC2609A_PMU_VBUSVADC 0x5F
+#define ATC2609A_PMU_VBUSIADC 0x60
+#define ATC2609A_PMU_SYSPWRADC 0x61
+#define ATC2609A_PMU_REMCONADC 0x62
+#define ATC2609A_PMU_SVCCADC 0x63
+#define ATC2609A_PMU_CHGIADC 0x64
+#define ATC2609A_PMU_IREFADC 0x65
+#define ATC2609A_PMU_BAKBATADC 0x66
+#define ATC2609A_PMU_ICTEMPADC 0x67
+#define ATC2609A_PMU_AUXADC0 0x68
+#define ATC2609A_PMU_AUXADC1 0x69
+#define ATC2609A_PMU_AUXADC2 0x6A
+#define ATC2609A_PMU_AUXADC3 0x6B
+#define ATC2609A_PMU_ICTEMPADC_ADJ 0x6C
+#define ATC2609A_PMU_BDG_CTL 0x6D
+#define ATC2609A_RTC_CTL 0x6E
+#define ATC2609A_RTC_MSALM 0x6F
+#define ATC2609A_RTC_HALM 0x70
+#define ATC2609A_RTC_YMDALM 0x71
+#define ATC2609A_RTC_MS 0x72
+#define ATC2609A_RTC_H 0x73
+#define ATC2609A_RTC_DC 0x74
+#define ATC2609A_RTC_YMD 0x75
+#define ATC2609A_EFUSE_DAT 0x76
+#define ATC2609A_EFUSECRTL1 0x77
+#define ATC2609A_EFUSECRTL2 0x78
+#define ATC2609A_PMU_DC4_CTL0 0x79
+#define ATC2609A_PMU_DC4_CTL1 0x7A
+#define ATC2609A_PMU_DC4_CTL2 0x7B
+#define ATC2609A_PMU_DC4_CTL3 0x7C
+#define ATC2609A_PMU_DC4_CTL4 0x7D
+#define ATC2609A_PMU_DC4_CTL5 0x7E
+#define ATC2609A_PMU_DC4_CTL6 0x7F
+#define ATC2609A_PMU_PWR_STATUS 0x80
+#define ATC2609A_PMU_S2_PWR 0x81
+#define ATC2609A_CLMT_CTL0 0x82
+#define ATC2609A_CLMT_DATA0 0x83
+#define ATC2609A_CLMT_DATA1 0x84
+#define ATC2609A_CLMT_DATA2 0x85
+#define ATC2609A_CLMT_DATA3 0x86
+#define ATC2609A_CLMT_ADD0 0x87
+#define ATC2609A_CLMT_ADD1 0x88
+#define ATC2609A_CLMT_OCV_TABLE 0x89
+#define ATC2609A_CLMT_R_TABLE 0x8A
+#define ATC2609A_PMU_PWRON_CTL0 0x8D
+#define ATC2609A_PMU_PWRON_CTL1 0x8E
+#define ATC2609A_PMU_PWRON_CTL2 0x8F
+#define ATC2609A_IRC_CTL 0x90
+#define ATC2609A_IRC_STAT 0x91
+#define ATC2609A_IRC_CC 0x92
+#define ATC2609A_IRC_KDC 0x93
+#define ATC2609A_IRC_WK 0x94
+#define ATC2609A_IRC_RCC 0x95
+
+/* AUDIO_OUT Registers */
+#define ATC2609A_AUDIOINOUT_CTL 0xA0
+#define ATC2609A_AUDIO_DEBUGOUTCTL 0xA1
+#define ATC2609A_DAC_DIGITALCTL 0xA2
+#define ATC2609A_DAC_VOLUMECTL0 0xA3
+#define ATC2609A_DAC_ANALOG0 0xA4
+#define ATC2609A_DAC_ANALOG1 0xA5
+#define ATC2609A_DAC_ANALOG2 0xA6
+#define ATC2609A_DAC_ANALOG3 0xA7
+
+/* AUDIO_IN Registers */
+#define ATC2609A_ADC_DIGITALCTL 0xA8
+#define ATC2609A_ADC_HPFCTL 0xA9
+#define ATC2609A_ADC_CTL 0xAA
+#define ATC2609A_AGC_CTL0 0xAB
+#define ATC2609A_AGC_CTL1 0xAC
+#define ATC2609A_AGC_CTL2 0xAD
+#define ATC2609A_ADC_ANALOG0 0xAE
+#define ATC2609A_ADC_ANALOG1 0xAF
+
+/* PCM_IF Registers */
+#define ATC2609A_PCM0_CTL 0xB0
+#define ATC2609A_PCM1_CTL 0xB1
+#define ATC2609A_PCM2_CTL 0xB2
+#define ATC2609A_PCMIF_CTL 0xB3
+
+/* CMU_CONTROL Registers */
+#define ATC2609A_CMU_DEVRST 0xC1
+
+/* INTS Registers */
+#define ATC2609A_INTS_PD 0xC8
+#define ATC2609A_INTS_MSK 0xC9
+
+/* MFP Registers */
+#define ATC2609A_MFP_CTL 0xD0
+#define ATC2609A_PAD_VSEL 0xD1
+#define ATC2609A_GPIO_OUTEN 0xD2
+#define ATC2609A_GPIO_INEN 0xD3
+#define ATC2609A_GPIO_DAT 0xD4
+#define ATC2609A_PAD_DRV 0xD5
+#define ATC2609A_PAD_EN 0xD6
+#define ATC2609A_DEBUG_SEL 0xD7
+#define ATC2609A_DEBUG_IE 0xD8
+#define ATC2609A_DEBUG_OE 0xD9
+#define ATC2609A_CHIP_VER 0xDC
+
+/* PWSI Registers */
+#define ATC2609A_PWSI_CTL 0xF0
+#define ATC2609A_PWSI_STATUS 0xF1
+
+/* TWSI Registers */
+#define ATC2609A_SADDR 0xFF
+
+/* PMU_SYS_CTL0 Register Mask Bits */
+#define ATC2609A_PMU_SYS_CTL0_IR_WK_EN BIT(5)
+#define ATC2609A_PMU_SYS_CTL0_RESET_WK_EN BIT(6)
+#define ATC2609A_PMU_SYS_CTL0_HDSW_WK_EN BIT(7)
+#define ATC2609A_PMU_SYS_CTL0_ALARM_WK_EN BIT(8)
+#define ATC2609A_PMU_SYS_CTL0_REM_CON_WK_EN BIT(9)
+#define ATC2609A_PMU_SYS_CTL0_RESTART_EN BIT(10)
+#define ATC2609A_PMU_SYS_CTL0_WKIRQ_WK_EN BIT(11)
+#define ATC2609A_PMU_SYS_CTL0_ONOFF_SHORT_WK_EN BIT(12)
+#define ATC2609A_PMU_SYS_CTL0_ONOFF_LONG_WK_EN BIT(13)
+#define ATC2609A_PMU_SYS_CTL0_WALL_WK_EN BIT(14)
+#define ATC2609A_PMU_SYS_CTL0_USB_WK_EN BIT(15)
+#define ATC2609A_PMU_SYS_CTL0_WK_ALL (GENMASK(15, 5) & (~BIT(10)))
+
+/* PMU_SYS_CTL1 Register Mask Bits */
+#define ATC2609A_PMU_SYS_CTL1_EN_S1 BIT(0)
+#define ATC2609A_PMU_SYS_CTL1_LB_S4_EN BIT(2)
+#define ATC2609A_PMU_SYS_CTL1_LB_S4 GENMASK(4, 3)
+#define ATC2609A_PMU_SYS_CTL1_LB_S4_3_1V BIT(4)
+#define ATC2609A_PMU_SYS_CTL1_IR_WK_FLAG BIT(5)
+#define ATC2609A_PMU_SYS_CTL1_RESET_WK_FLAG BIT(6)
+#define ATC2609A_PMU_SYS_CTL1_HDSW_WK_FLAG BIT(7)
+#define ATC2609A_PMU_SYS_CTL1_ALARM_WK_FLAG BIT(8)
+#define ATC2609A_PMU_SYS_CTL1_REM_CON_WK_FLAG BIT(9)
+#define ATC2609A_PMU_SYS_CTL1_RESTART_WK_FLAG BIT(10)
+#define ATC2609A_PMU_SYS_CTL1_WKIRQ_WK_FLAG BIT(11)
+#define ATC2609A_PMU_SYS_CTL1_ONOFF_SHORT_WK_FLAG BIT(12)
+#define ATC2609A_PMU_SYS_CTL1_ONOFF_LONG_WK_FLAG BIT(13)
+#define ATC2609A_PMU_SYS_CTL1_WALL_WK_FLAG BIT(14)
+#define ATC2609A_PMU_SYS_CTL1_USB_WK_FLAG BIT(15)
+
+/* PMU_SYS_CTL2 Register Mask Bits */
+#define ATC2609A_PMU_SYS_CTL2_PMU_A_EN BIT(0)
+#define ATC2609A_PMU_SYS_CTL2_ONOFF_PRESS_INT_EN BIT(1)
+#define ATC2609A_PMU_SYS_CTL2_ONOFF_PRESS_PD BIT(2)
+#define ATC2609A_PMU_SYS_CTL2_S2TIMER GENMASK(5, 3)
+#define ATC2609A_PMU_SYS_CTL2_S2_TIMER_EN BIT(6)
+#define ATC2609A_PMU_SYS_CTL2_ONOFF_RESET_TIME_SEL GENMASK(8, 7)
+#define ATC2609A_PMU_SYS_CTL2_ONOFF_RESET_EN BIT(9)
+#define ATC2609A_PMU_SYS_CTL2_ONOFF_PRESS_TIME GENMASK(11, 10)
+#define ATC2609A_PMU_SYS_CTL2_ONOFF_LSP_INT_EN BIT(12)
+#define ATC2609A_PMU_SYS_CTL2_ONOFF_LONG_PRESS BIT(13)
+#define ATC2609A_PMU_SYS_CTL2_ONOFF_SHORT_PRESS BIT(14)
+#define ATC2609A_PMU_SYS_CTL2_ONOFF_PRESS BIT(15)
+
+/* PMU_SYS_CTL3 Register Mask Bits */
+#define ATC2609A_PMU_SYS_CTL3_S2S3TOS1_TIMER GENMASK(8, 7)
+#define ATC2609A_PMU_SYS_CTL3_S2S3TOS1_TIMER_EN BIT(9)
+#define ATC2609A_PMU_SYS_CTL3_S3_TIMER GENMASK(12, 10)
+#define ATC2609A_PMU_SYS_CTL3_S3_TIMER_EN BIT(13)
+#define ATC2609A_PMU_SYS_CTL3_EN_S3 BIT(14)
+#define ATC2609A_PMU_SYS_CTL3_EN_S2 BIT(15)
+
+/* PMU_SYS_CTL5 Register Mask Bits */
+#define ATC2609A_PMU_SYS_CTL5_WALLWKDTEN BIT(7)
+#define ATC2609A_PMU_SYS_CTL5_VBUSWKDTEN BIT(8)
+#define ATC2609A_PMU_SYS_CTL5_REMCON_DECT_EN BIT(9)
+#define ATC2609A_PMU_SYS_CTL5_ONOFF_8S_SEL BIT(10)
+
+/* INTS_MSK Register Mask Bits */
+#define ATC2609A_INTS_MSK_AUDIO BIT(0)
+#define ATC2609A_INTS_MSK_OV BIT(1)
+#define ATC2609A_INTS_MSK_OC BIT(2)
+#define ATC2609A_INTS_MSK_OT BIT(3)
+#define ATC2609A_INTS_MSK_UV BIT(4)
+#define ATC2609A_INTS_MSK_ALARM BIT(5)
+#define ATC2609A_INTS_MSK_ONOFF BIT(6)
+#define ATC2609A_INTS_MSK_WKUP BIT(7)
+#define ATC2609A_INTS_MSK_IR BIT(8)
+#define ATC2609A_INTS_MSK_REMCON BIT(9)
+#define ATC2609A_INTS_MSK_POWERIN BIT(10)
+
+/* CMU_DEVRST Register Mask Bits */
+#define ATC2609A_CMU_DEVRST_AUDIO BIT(0)
+#define ATC2609A_CMU_DEVRST_MFP BIT(1)
+#define ATC2609A_CMU_DEVRST_INTS BIT(2)
+
+/* PAD_EN Register Mask Bits */
+#define ATC2609A_PAD_EN_EXTIRQ BIT(0)
+
+#endif /* __LINUX_MFD_ATC260X_ATC2609A_H */
--- /dev/null
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Core MFD defines for ATC260x PMICs
+ *
+ * Copyright (C) 2019 Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
+ * Copyright (C) 2020 Cristian Ciocaltea <cristian.ciocaltea@gmail.com>
+ */
+
+#ifndef __LINUX_MFD_ATC260X_CORE_H
+#define __LINUX_MFD_ATC260X_CORE_H
+
+#include <linux/mfd/atc260x/atc2603c.h>
+#include <linux/mfd/atc260x/atc2609a.h>
+
+enum atc260x_type {
+ ATC2603A = 0,
+ ATC2603C,
+ ATC2609A,
+};
+
+enum atc260x_ver {
+ ATC260X_A = 0,
+ ATC260X_B,
+ ATC260X_C,
+ ATC260X_D,
+ ATC260X_E,
+ ATC260X_F,
+ ATC260X_G,
+ ATC260X_H,
+};
+
+struct atc260x {
+ struct device *dev;
+
+ struct regmap *regmap;
+ const struct regmap_irq_chip *regmap_irq_chip;
+ struct regmap_irq_chip_data *irq_data;
+
+ struct mutex *regmap_mutex; /* mutex for custom regmap locking */
+
+ const struct mfd_cell *cells;
+ int nr_cells;
+ int irq;
+
+ enum atc260x_type ic_type;
+ enum atc260x_ver ic_ver;
+ const char *type_name;
+ unsigned int rev_reg;
+
+ const struct atc260x_init_regs *init_regs; /* regs for device init */
+};
+
+struct regmap_config;
+
+int atc260x_match_device(struct atc260x *atc260x, struct regmap_config *regmap_cfg);
+int atc260x_device_probe(struct atc260x *atc260x);
+
+#endif /* __LINUX_MFD_ATC260X_CORE_H */
projects / platform / kernel / linux-starfive.git / commitdiff