leds: move LED trigger drivers into new subdirectory

For better driver management, new subdirectory, 'trigger' is created.
All LED trigger drivers are moved into this directory.

Internal header, 'leds.h' is included in each LED trigger drivers.
Fix the location of header file, "leds.h" -> "../leds.h" in driver files.
One exception is here, 'ledtrig-timer.c'.
There is no need to include 'leds.h'. so '#include "leds.h"' line was removed.

Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>

diff --git a/drivers/leds/Kconfig b/drivers/leds/Kconfig
index c7f7550..d44806d 100644 (file)
--- a/drivers/leds/Kconfig
+++ b/drivers/leds/Kconfig
@@ -479,106 +479,7 @@ config LEDS_BLINKM
          This option enables support for the BlinkM RGB LED connected
          through I2C. Say Y to enable support for the BlinkM LED.
 
-config LEDS_TRIGGERS
-       bool "LED Trigger support"
-       depends on LEDS_CLASS
-       help
-         This option enables trigger support for the leds class.
-         These triggers allow kernel events to drive the LEDs and can
-         be configured via sysfs. If unsure, say Y.
-
 comment "LED Triggers"
-
-config LEDS_TRIGGER_TIMER
-       tristate "LED Timer Trigger"
-       depends on LEDS_TRIGGERS
-       help
-         This allows LEDs to be controlled by a programmable timer
-         via sysfs. Some LED hardware can be programmed to start
-         blinking the LED without any further software interaction.
-         For more details read Documentation/leds/leds-class.txt.
-
-         If unsure, say Y.
-
-config LEDS_TRIGGER_ONESHOT
-       tristate "LED One-shot Trigger"
-       depends on LEDS_TRIGGERS
-       help
-         This allows LEDs to blink in one-shot pulses with parameters
-         controlled via sysfs.  It's useful to notify the user on
-         sporadic events, when there are no clear begin and end trap points,
-         or on dense events, where this blinks the LED at constant rate if
-         rearmed continuously.
-
-         It also shows how to use the led_blink_set_oneshot() function.
-
-         If unsure, say Y.
-
-config LEDS_TRIGGER_IDE_DISK
-       bool "LED IDE Disk Trigger"
-       depends on IDE_GD_ATA
-       depends on LEDS_TRIGGERS
-       help
-         This allows LEDs to be controlled by IDE disk activity.
-         If unsure, say Y.
-
-config LEDS_TRIGGER_HEARTBEAT
-       tristate "LED Heartbeat Trigger"
-       depends on LEDS_TRIGGERS
-       help
-         This allows LEDs to be controlled by a CPU load average.
-         The flash frequency is a hyperbolic function of the 1-minute
-         load average.
-         If unsure, say Y.
-
-config LEDS_TRIGGER_BACKLIGHT
-       tristate "LED backlight Trigger"
-       depends on LEDS_TRIGGERS
-       help
-         This allows LEDs to be controlled as a backlight device: they
-         turn off and on when the display is blanked and unblanked.
-
-         If unsure, say N.
-
-config LEDS_TRIGGER_CPU
-       bool "LED CPU Trigger"
-       depends on LEDS_TRIGGERS
-       help
-         This allows LEDs to be controlled by active CPUs. This shows
-         the active CPUs across an array of LEDs so you can see which
-         CPUs are active on the system at any given moment.
-
-         If unsure, say N.
-
-config LEDS_TRIGGER_GPIO
-       tristate "LED GPIO Trigger"
-       depends on LEDS_TRIGGERS
-       depends on GPIOLIB
-       help
-         This allows LEDs to be controlled by gpio events. It's good
-         when using gpios as switches and triggering the needed LEDs
-         from there. One use case is n810's keypad LEDs that could
-         be triggered by this trigger when user slides up to show
-         keypad.
-
-         If unsure, say N.
-
-config LEDS_TRIGGER_DEFAULT_ON
-       tristate "LED Default ON Trigger"
-       depends on LEDS_TRIGGERS
-       help
-         This allows LEDs to be initialised in the ON state.
-         If unsure, say Y.
-
-comment "iptables trigger is under Netfilter config (LED target)"
-       depends on LEDS_TRIGGERS
-
-config LEDS_TRIGGER_TRANSIENT
-       tristate "LED Transient Trigger"
-       depends on LEDS_TRIGGERS
-       help
-         This allows one time activation of a transient state on
-         GPIO/PWM based hardware.
-         If unsure, say Y.
+source "drivers/leds/trigger/Kconfig"
 
 endif # NEW_LEDS

diff --git a/drivers/leds/Makefile b/drivers/leds/Makefile
index ab8f5c5..ac28977 100644 (file)
--- a/drivers/leds/Makefile
+++ b/drivers/leds/Makefile
@@ -58,12 +58,4 @@ obj-$(CONFIG_LEDS_BLINKM)            += leds-blinkm.o
 obj-$(CONFIG_LEDS_DAC124S085)          += leds-dac124s085.o
 
 # LED Triggers
-obj-$(CONFIG_LEDS_TRIGGER_TIMER)       += ledtrig-timer.o
-obj-$(CONFIG_LEDS_TRIGGER_ONESHOT)     += ledtrig-oneshot.o
-obj-$(CONFIG_LEDS_TRIGGER_IDE_DISK)    += ledtrig-ide-disk.o
-obj-$(CONFIG_LEDS_TRIGGER_HEARTBEAT)   += ledtrig-heartbeat.o
-obj-$(CONFIG_LEDS_TRIGGER_BACKLIGHT)   += ledtrig-backlight.o
-obj-$(CONFIG_LEDS_TRIGGER_GPIO)                += ledtrig-gpio.o
-obj-$(CONFIG_LEDS_TRIGGER_CPU)         += ledtrig-cpu.o
-obj-$(CONFIG_LEDS_TRIGGER_DEFAULT_ON)  += ledtrig-default-on.o
-obj-$(CONFIG_LEDS_TRIGGER_TRANSIENT)   += ledtrig-transient.o
+obj-$(CONFIG_LEDS_TRIGGERS)            += trigger/

diff --git a/drivers/leds/trigger/Kconfig b/drivers/leds/trigger/Kconfig
new file mode 100644 (file)
index 0000000..eaa286d
--- /dev/null
+++ b/drivers/leds/trigger/Kconfig
@@ -0,0 +1,103 @@
+menuconfig LEDS_TRIGGERS
+       bool "LED Trigger support"
+       depends on LEDS_CLASS
+       help
+         This option enables trigger support for the leds class.
+         These triggers allow kernel events to drive the LEDs and can
+         be configured via sysfs. If unsure, say Y.
+
+if LEDS_TRIGGERS
+
+config LEDS_TRIGGER_TIMER
+       tristate "LED Timer Trigger"
+       depends on LEDS_TRIGGERS
+       help
+         This allows LEDs to be controlled by a programmable timer
+         via sysfs. Some LED hardware can be programmed to start
+         blinking the LED without any further software interaction.
+         For more details read Documentation/leds/leds-class.txt.
+
+         If unsure, say Y.
+
+config LEDS_TRIGGER_ONESHOT
+       tristate "LED One-shot Trigger"
+       depends on LEDS_TRIGGERS
+       help
+         This allows LEDs to blink in one-shot pulses with parameters
+         controlled via sysfs.  It's useful to notify the user on
+         sporadic events, when there are no clear begin and end trap points,
+         or on dense events, where this blinks the LED at constant rate if
+         rearmed continuously.
+
+         It also shows how to use the led_blink_set_oneshot() function.
+
+         If unsure, say Y.
+
+config LEDS_TRIGGER_IDE_DISK
+       bool "LED IDE Disk Trigger"
+       depends on IDE_GD_ATA
+       depends on LEDS_TRIGGERS
+       help
+         This allows LEDs to be controlled by IDE disk activity.
+         If unsure, say Y.
+
+config LEDS_TRIGGER_HEARTBEAT
+       tristate "LED Heartbeat Trigger"
+       depends on LEDS_TRIGGERS
+       help
+         This allows LEDs to be controlled by a CPU load average.
+         The flash frequency is a hyperbolic function of the 1-minute
+         load average.
+         If unsure, say Y.
+
+config LEDS_TRIGGER_BACKLIGHT
+       tristate "LED backlight Trigger"
+       depends on LEDS_TRIGGERS
+       help
+         This allows LEDs to be controlled as a backlight device: they
+         turn off and on when the display is blanked and unblanked.
+
+         If unsure, say N.
+
+config LEDS_TRIGGER_CPU
+       bool "LED CPU Trigger"
+       depends on LEDS_TRIGGERS
+       help
+         This allows LEDs to be controlled by active CPUs. This shows
+         the active CPUs across an array of LEDs so you can see which
+         CPUs are active on the system at any given moment.
+
+         If unsure, say N.
+
+config LEDS_TRIGGER_GPIO
+       tristate "LED GPIO Trigger"
+       depends on LEDS_TRIGGERS
+       depends on GPIOLIB
+       help
+         This allows LEDs to be controlled by gpio events. It's good
+         when using gpios as switches and triggering the needed LEDs
+         from there. One use case is n810's keypad LEDs that could
+         be triggered by this trigger when user slides up to show
+         keypad.
+
+         If unsure, say N.
+
+config LEDS_TRIGGER_DEFAULT_ON
+       tristate "LED Default ON Trigger"
+       depends on LEDS_TRIGGERS
+       help
+         This allows LEDs to be initialised in the ON state.
+         If unsure, say Y.
+
+comment "iptables trigger is under Netfilter config (LED target)"
+       depends on LEDS_TRIGGERS
+
+config LEDS_TRIGGER_TRANSIENT
+       tristate "LED Transient Trigger"
+       depends on LEDS_TRIGGERS
+       help
+         This allows one time activation of a transient state on
+         GPIO/PWM based hardware.
+         If unsure, say Y.
+
+endif # LEDS_TRIGGERS

diff --git a/drivers/leds/trigger/Makefile b/drivers/leds/trigger/Makefile
new file mode 100644 (file)
index 0000000..554e46e
--- /dev/null
+++ b/drivers/leds/trigger/Makefile
@@ -0,0 +1,9 @@
+obj-$(CONFIG_LEDS_TRIGGER_TIMER)       += ledtrig-timer.o
+obj-$(CONFIG_LEDS_TRIGGER_ONESHOT)     += ledtrig-oneshot.o
+obj-$(CONFIG_LEDS_TRIGGER_IDE_DISK)    += ledtrig-ide-disk.o
+obj-$(CONFIG_LEDS_TRIGGER_HEARTBEAT)   += ledtrig-heartbeat.o
+obj-$(CONFIG_LEDS_TRIGGER_BACKLIGHT)   += ledtrig-backlight.o
+obj-$(CONFIG_LEDS_TRIGGER_GPIO)                += ledtrig-gpio.o
+obj-$(CONFIG_LEDS_TRIGGER_CPU)         += ledtrig-cpu.o
+obj-$(CONFIG_LEDS_TRIGGER_DEFAULT_ON)  += ledtrig-default-on.o
+obj-$(CONFIG_LEDS_TRIGGER_TRANSIENT)   += ledtrig-transient.o

diff --git a/drivers/leds/ledtrig-backlight.c b/drivers/leds/trigger/ledtrig-backlight.c
similarity index 99%
rename from drivers/leds/ledtrig-backlight.c
rename to drivers/leds/trigger/ledtrig-backlight.c
index 027a2b1..3c9c88a 100644 (file)
--- a/drivers/leds/ledtrig-backlight.c
+++ b/drivers/leds/trigger/ledtrig-backlight.c
@@ -16,7 +16,7 @@
 #include <linux/init.h>
 #include <linux/fb.h>
 #include <linux/leds.h>
-#include "leds.h"
+#include "../leds.h"
 
 #define BLANK          1
 #define UNBLANK                0

diff --git a/drivers/leds/ledtrig-cpu.c b/drivers/leds/trigger/ledtrig-cpu.c
similarity index 99%
rename from drivers/leds/ledtrig-cpu.c
rename to drivers/leds/trigger/ledtrig-cpu.c
index 4239b39..118335e 100644 (file)
--- a/drivers/leds/ledtrig-cpu.c
+++ b/drivers/leds/trigger/ledtrig-cpu.c
@@ -26,7 +26,7 @@
 #include <linux/percpu.h>
 #include <linux/syscore_ops.h>
 #include <linux/rwsem.h>
-#include "leds.h"
+#include "../leds.h"
 
 #define MAX_NAME_LEN   8
 

diff --git a/drivers/leds/ledtrig-default-on.c b/drivers/leds/trigger/ledtrig-default-on.c
similarity index 98%
rename from drivers/leds/ledtrig-default-on.c
rename to drivers/leds/trigger/ledtrig-default-on.c
index eac1f1b..81a91be 100644 (file)
--- a/drivers/leds/ledtrig-default-on.c
+++ b/drivers/leds/trigger/ledtrig-default-on.c
@@ -15,7 +15,7 @@
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/leds.h>
-#include "leds.h"
+#include "../leds.h"
 
 static void defon_trig_activate(struct led_classdev *led_cdev)
 {

diff --git a/drivers/leds/ledtrig-gpio.c b/drivers/leds/trigger/ledtrig-gpio.c
similarity index 99%
rename from drivers/leds/ledtrig-gpio.c
rename to drivers/leds/trigger/ledtrig-gpio.c
index 72e3ebf..35812e3 100644 (file)
--- a/drivers/leds/ledtrig-gpio.c
+++ b/drivers/leds/trigger/ledtrig-gpio.c
@@ -17,7 +17,7 @@
 #include <linux/workqueue.h>
 #include <linux/leds.h>
 #include <linux/slab.h>
-#include "leds.h"
+#include "../leds.h"
 
 struct gpio_trig_data {
        struct led_classdev *led;

diff --git a/drivers/leds/ledtrig-heartbeat.c b/drivers/leds/trigger/ledtrig-heartbeat.c
similarity index 99%
rename from drivers/leds/ledtrig-heartbeat.c
rename to drivers/leds/trigger/ledtrig-heartbeat.c
index 1edc746..5c8464a 100644 (file)
--- a/drivers/leds/ledtrig-heartbeat.c
+++ b/drivers/leds/trigger/ledtrig-heartbeat.c
@@ -19,7 +19,7 @@
 #include <linux/sched.h>
 #include <linux/leds.h>
 #include <linux/reboot.h>
-#include "leds.h"
+#include "../leds.h"
 
 static int panic_heartbeats;
 

diff --git a/drivers/leds/ledtrig-ide-disk.c b/drivers/leds/trigger/ledtrig-ide-disk.c
similarity index 100%
rename from drivers/leds/ledtrig-ide-disk.c
rename to drivers/leds/trigger/ledtrig-ide-disk.c

diff --git a/drivers/leds/ledtrig-oneshot.c b/drivers/leds/trigger/ledtrig-oneshot.c
similarity index 99%
rename from drivers/leds/ledtrig-oneshot.c
rename to drivers/leds/trigger/ledtrig-oneshot.c
index 2c029aa..cb4c746 100644 (file)
--- a/drivers/leds/ledtrig-oneshot.c
+++ b/drivers/leds/trigger/ledtrig-oneshot.c
@@ -18,7 +18,7 @@
 #include <linux/ctype.h>
 #include <linux/slab.h>
 #include <linux/leds.h>
-#include "leds.h"
+#include "../leds.h"
 
 #define DEFAULT_DELAY 100
 

diff --git a/drivers/leds/ledtrig-timer.c b/drivers/leds/trigger/ledtrig-timer.c
similarity index 99%
rename from drivers/leds/ledtrig-timer.c
rename to drivers/leds/trigger/ledtrig-timer.c
index f774d05..8d09327 100644 (file)
--- a/drivers/leds/ledtrig-timer.c
+++ b/drivers/leds/trigger/ledtrig-timer.c
@@ -17,7 +17,6 @@
 #include <linux/device.h>
 #include <linux/ctype.h>
 #include <linux/leds.h>
-#include "leds.h"
 
 static ssize_t led_delay_on_show(struct device *dev,
                struct device_attribute *attr, char *buf)

diff --git a/drivers/leds/ledtrig-transient.c b/drivers/leds/trigger/ledtrig-transient.c
similarity index 99%
rename from drivers/leds/ledtrig-transient.c
rename to drivers/leds/trigger/ledtrig-transient.c
index 398f104..e5abc00 100644 (file)
--- a/drivers/leds/ledtrig-transient.c
+++ b/drivers/leds/trigger/ledtrig-transient.c
@@ -25,7 +25,7 @@
 #include <linux/slab.h>
 #include <linux/timer.h>
 #include <linux/leds.h>
-#include "leds.h"
+#include "../leds.h"
 
 struct transient_trig_data {
        int activate;