--- /dev/null
+/*
+ * SC268xx.c: Serial driver for Philiphs SC2681/SC2692 devices.
+ *
+ * Copyright (C) 2006,2007 Thomas Bogendörfer (tsbogend@alpha.franken.de)
+ */
+
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/errno.h>
+#include <linux/tty.h>
+#include <linux/tty_flip.h>
+#include <linux/major.h>
+#include <linux/circ_buf.h>
+#include <linux/serial.h>
+#include <linux/sysrq.h>
+#include <linux/console.h>
+#include <linux/spinlock.h>
+#include <linux/slab.h>
+#include <linux/delay.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/irq.h>
+
+#if defined(CONFIG_MAGIC_SYSRQ)
+#define SUPPORT_SYSRQ
+#endif
+
+#include <linux/serial_core.h>
+
+#define SC26XX_MAJOR 204
+#define SC26XX_MINOR_START 205
+#define SC26XX_NR 2
+
+struct uart_sc26xx_port {
+ struct uart_port port[2];
+ u8 dsr_mask[2];
+ u8 cts_mask[2];
+ u8 dcd_mask[2];
+ u8 ri_mask[2];
+ u8 dtr_mask[2];
+ u8 rts_mask[2];
+ u8 imr;
+};
+
+/* register common to both ports */
+#define RD_ISR 0x14
+#define RD_IPR 0x34
+
+#define WR_ACR 0x10
+#define WR_IMR 0x14
+#define WR_OPCR 0x34
+#define WR_OPR_SET 0x38
+#define WR_OPR_CLR 0x3C
+
+/* access common register */
+#define READ_SC(p, r) readb((p)->membase + RD_##r)
+#define WRITE_SC(p, r, v) writeb((v), (p)->membase + WR_##r)
+
+/* register per port */
+#define RD_PORT_MRx 0x00
+#define RD_PORT_SR 0x04
+#define RD_PORT_RHR 0x0c
+
+#define WR_PORT_MRx 0x00
+#define WR_PORT_CSR 0x04
+#define WR_PORT_CR 0x08
+#define WR_PORT_THR 0x0c
+
+/* SR bits */
+#define SR_BREAK (1 << 7)
+#define SR_FRAME (1 << 6)
+#define SR_PARITY (1 << 5)
+#define SR_OVERRUN (1 << 4)
+#define SR_TXRDY (1 << 2)
+#define SR_RXRDY (1 << 0)
+
+#define CR_RES_MR (1 << 4)
+#define CR_RES_RX (2 << 4)
+#define CR_RES_TX (3 << 4)
+#define CR_STRT_BRK (6 << 4)
+#define CR_STOP_BRK (7 << 4)
+#define CR_DIS_TX (1 << 3)
+#define CR_ENA_TX (1 << 2)
+#define CR_DIS_RX (1 << 1)
+#define CR_ENA_RX (1 << 0)
+
+/* ISR bits */
+#define ISR_RXRDYB (1 << 5)
+#define ISR_TXRDYB (1 << 4)
+#define ISR_RXRDYA (1 << 1)
+#define ISR_TXRDYA (1 << 0)
+
+/* IMR bits */
+#define IMR_RXRDY (1 << 1)
+#define IMR_TXRDY (1 << 0)
+
+/* access port register */
+static inline u8 read_sc_port(struct uart_port *p, u8 reg)
+{
+ return readb(p->membase + p->line * 0x20 + reg);
+}
+
+static inline void write_sc_port(struct uart_port *p, u8 reg, u8 val)
+{
+ writeb(val, p->membase + p->line * 0x20 + reg);
+}
+
+#define READ_SC_PORT(p, r) read_sc_port(p, RD_PORT_##r)
+#define WRITE_SC_PORT(p, r, v) write_sc_port(p, WR_PORT_##r, v)
+
+static void sc26xx_enable_irq(struct uart_port *port, int mask)
+{
+ struct uart_sc26xx_port *up;
+ int line = port->line;
+
+ port -= line;
+ up = container_of(port, struct uart_sc26xx_port, port[0]);
+
+ up->imr |= mask << (line * 4);
+ WRITE_SC(port, IMR, up->imr);
+}
+
+static void sc26xx_disable_irq(struct uart_port *port, int mask)
+{
+ struct uart_sc26xx_port *up;
+ int line = port->line;
+
+ port -= line;
+ up = container_of(port, struct uart_sc26xx_port, port[0]);
+
+ up->imr &= ~(mask << (line * 4));
+ WRITE_SC(port, IMR, up->imr);
+}
+
+static struct tty_struct *receive_chars(struct uart_port *port)
+{
+ struct tty_struct *tty = NULL;
+ int limit = 10000;
+ unsigned char ch;
+ char flag;
+ u8 status;
+
+ if (port->info != NULL) /* Unopened serial console */
+ tty = port->info->tty;
+
+ while (limit-- > 0) {
+ status = READ_SC_PORT(port, SR);
+ if (!(status & SR_RXRDY))
+ break;
+ ch = READ_SC_PORT(port, RHR);
+
+ flag = TTY_NORMAL;
+ port->icount.rx++;
+
+ if (unlikely(status & (SR_BREAK | SR_FRAME |
+ SR_PARITY | SR_OVERRUN))) {
+ if (status & SR_BREAK) {
+ status &= ~(SR_PARITY | SR_FRAME);
+ port->icount.brk++;
+ if (uart_handle_break(port))
+ continue;
+ } else if (status & SR_PARITY)
+ port->icount.parity++;
+ else if (status & SR_FRAME)
+ port->icount.frame++;
+ if (status & SR_OVERRUN)
+ port->icount.overrun++;
+
+ status &= port->read_status_mask;
+ if (status & SR_BREAK)
+ flag = TTY_BREAK;
+ else if (status & SR_PARITY)
+ flag = TTY_PARITY;
+ else if (status & SR_FRAME)
+ flag = TTY_FRAME;
+ }
+
+ if (uart_handle_sysrq_char(port, ch))
+ continue;
+
+ if (status & port->ignore_status_mask)
+ continue;
+
+ tty_insert_flip_char(tty, ch, flag);
+ }
+ return tty;
+}
+
+static void transmit_chars(struct uart_port *port)
+{
+ struct circ_buf *xmit;
+
+ if (!port->info)
+ return;
+
+ xmit = &port->info->xmit;
+ if (uart_circ_empty(xmit) || uart_tx_stopped(port)) {
+ sc26xx_disable_irq(port, IMR_TXRDY);
+ return;
+ }
+ while (!uart_circ_empty(xmit)) {
+ if (!(READ_SC_PORT(port, SR) & SR_TXRDY))
+ break;
+
+ WRITE_SC_PORT(port, THR, xmit->buf[xmit->tail]);
+ xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
+ port->icount.tx++;
+ }
+ if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
+ uart_write_wakeup(port);
+}
+
+static irqreturn_t sc26xx_interrupt(int irq, void *dev_id)
+{
+ struct uart_sc26xx_port *up = dev_id;
+ struct tty_struct *tty;
+ unsigned long flags;
+ u8 isr;
+
+ spin_lock_irqsave(&up->port[0].lock, flags);
+
+ tty = NULL;
+ isr = READ_SC(&up->port[0], ISR);
+ if (isr & ISR_TXRDYA)
+ transmit_chars(&up->port[0]);
+ if (isr & ISR_RXRDYA)
+ tty = receive_chars(&up->port[0]);
+
+ spin_unlock(&up->port[0].lock);
+
+ if (tty)
+ tty_flip_buffer_push(tty);
+
+ spin_lock(&up->port[1].lock);
+
+ tty = NULL;
+ if (isr & ISR_TXRDYB)
+ transmit_chars(&up->port[1]);
+ if (isr & ISR_RXRDYB)
+ tty = receive_chars(&up->port[1]);
+
+ spin_unlock_irqrestore(&up->port[1].lock, flags);
+
+ if (tty)
+ tty_flip_buffer_push(tty);
+
+ return IRQ_HANDLED;
+}
+
+/* port->lock is not held. */
+static unsigned int sc26xx_tx_empty(struct uart_port *port)
+{
+ return (READ_SC_PORT(port, SR) & SR_TXRDY) ? TIOCSER_TEMT : 0;
+}
+
+/* port->lock held by caller. */
+static void sc26xx_set_mctrl(struct uart_port *port, unsigned int mctrl)
+{
+ struct uart_sc26xx_port *up;
+ int line = port->line;
+
+ port -= line;
+ up = container_of(port, struct uart_sc26xx_port, port[0]);
+
+ if (up->dtr_mask[line]) {
+ if (mctrl & TIOCM_DTR)
+ WRITE_SC(port, OPR_SET, up->dtr_mask[line]);
+ else
+ WRITE_SC(port, OPR_CLR, up->dtr_mask[line]);
+ }
+ if (up->rts_mask[line]) {
+ if (mctrl & TIOCM_RTS)
+ WRITE_SC(port, OPR_SET, up->rts_mask[line]);
+ else
+ WRITE_SC(port, OPR_CLR, up->rts_mask[line]);
+ }
+}
+
+/* port->lock is held by caller and interrupts are disabled. */
+static unsigned int sc26xx_get_mctrl(struct uart_port *port)
+{
+ struct uart_sc26xx_port *up;
+ int line = port->line;
+ unsigned int mctrl = TIOCM_DSR | TIOCM_CTS | TIOCM_CAR;
+ u8 ipr;
+
+ port -= line;
+ up = container_of(port, struct uart_sc26xx_port, port[0]);
+ ipr = READ_SC(port, IPR) ^ 0xff;
+
+ if (up->dsr_mask[line]) {
+ mctrl &= ~TIOCM_DSR;
+ mctrl |= ipr & up->dsr_mask[line] ? TIOCM_DSR : 0;
+ }
+ if (up->cts_mask[line]) {
+ mctrl &= ~TIOCM_CTS;
+ mctrl |= ipr & up->cts_mask[line] ? TIOCM_CTS : 0;
+ }
+ if (up->dcd_mask[line]) {
+ mctrl &= ~TIOCM_CAR;
+ mctrl |= ipr & up->dcd_mask[line] ? TIOCM_CAR : 0;
+ }
+ if (up->ri_mask[line]) {
+ mctrl &= ~TIOCM_RNG;
+ mctrl |= ipr & up->ri_mask[line] ? TIOCM_RNG : 0;
+ }
+ return mctrl;
+}
+
+/* port->lock held by caller. */
+static void sc26xx_stop_tx(struct uart_port *port)
+{
+ return;
+}
+
+/* port->lock held by caller. */
+static void sc26xx_start_tx(struct uart_port *port)
+{
+ struct circ_buf *xmit = &port->info->xmit;
+
+ while (!uart_circ_empty(xmit)) {
+ if (!(READ_SC_PORT(port, SR) & SR_TXRDY)) {
+ sc26xx_enable_irq(port, IMR_TXRDY);
+ break;
+ }
+ WRITE_SC_PORT(port, THR, xmit->buf[xmit->tail]);
+ xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
+ port->icount.tx++;
+ }
+}
+
+/* port->lock held by caller. */
+static void sc26xx_stop_rx(struct uart_port *port)
+{
+}
+
+/* port->lock held by caller. */
+static void sc26xx_enable_ms(struct uart_port *port)
+{
+}
+
+/* port->lock is not held. */
+static void sc26xx_break_ctl(struct uart_port *port, int break_state)
+{
+ if (break_state == -1)
+ WRITE_SC_PORT(port, CR, CR_STRT_BRK);
+ else
+ WRITE_SC_PORT(port, CR, CR_STOP_BRK);
+}
+
+/* port->lock is not held. */
+static int sc26xx_startup(struct uart_port *port)
+{
+ sc26xx_disable_irq(port, IMR_TXRDY | IMR_RXRDY);
+ WRITE_SC(port, OPCR, 0);
+
+ /* reset tx and rx */
+ WRITE_SC_PORT(port, CR, CR_RES_RX);
+ WRITE_SC_PORT(port, CR, CR_RES_TX);
+
+ /* start rx/tx */
+ WRITE_SC_PORT(port, CR, CR_ENA_TX | CR_ENA_RX);
+
+ /* enable irqs */
+ sc26xx_enable_irq(port, IMR_RXRDY);
+ return 0;
+}
+
+/* port->lock is not held. */
+static void sc26xx_shutdown(struct uart_port *port)
+{
+ /* disable interrupst */
+ sc26xx_disable_irq(port, IMR_TXRDY | IMR_RXRDY);
+
+ /* stop tx/rx */
+ WRITE_SC_PORT(port, CR, CR_DIS_TX | CR_DIS_RX);
+}
+
+/* port->lock is not held. */
+static void sc26xx_set_termios(struct uart_port *port, struct ktermios *termios,
+ struct ktermios *old)
+{
+ unsigned int baud = uart_get_baud_rate(port, termios, old, 0, 4000000);
+ unsigned int quot = uart_get_divisor(port, baud);
+ unsigned int iflag, cflag;
+ unsigned long flags;
+ u8 mr1, mr2, csr;
+
+ spin_lock_irqsave(&port->lock, flags);
+
+ while ((READ_SC_PORT(port, SR) & ((1 << 3) | (1 << 2))) != 0xc)
+ udelay(2);
+
+ WRITE_SC_PORT(port, CR, CR_DIS_TX | CR_DIS_RX);
+
+ iflag = termios->c_iflag;
+ cflag = termios->c_cflag;
+
+ port->read_status_mask = SR_OVERRUN;
+ if (iflag & INPCK)
+ port->read_status_mask |= SR_PARITY | SR_FRAME;
+ if (iflag & (BRKINT | PARMRK))
+ port->read_status_mask |= SR_BREAK;
+
+ port->ignore_status_mask = 0;
+ if (iflag & IGNBRK)
+ port->ignore_status_mask |= SR_BREAK;
+ if ((cflag & CREAD) == 0)
+ port->ignore_status_mask |= SR_BREAK | SR_FRAME |
+ SR_PARITY | SR_OVERRUN;
+
+ switch (cflag & CSIZE) {
+ case CS5:
+ mr1 = 0x00;
+ break;
+ case CS6:
+ mr1 = 0x01;
+ break;
+ case CS7:
+ mr1 = 0x02;
+ break;
+ default:
+ case CS8:
+ mr1 = 0x03;
+ break;
+ }
+ mr2 = 0x07;
+ if (cflag & CSTOPB)
+ mr2 = 0x0f;
+ if (cflag & PARENB) {
+ if (cflag & PARODD)
+ mr1 |= (1 << 2);
+ } else
+ mr1 |= (2 << 3);
+
+ switch (baud) {
+ case 50:
+ csr = 0x00;
+ break;
+ case 110:
+ csr = 0x11;
+ break;
+ case 134:
+ csr = 0x22;
+ break;
+ case 200:
+ csr = 0x33;
+ break;
+ case 300:
+ csr = 0x44;
+ break;
+ case 600:
+ csr = 0x55;
+ break;
+ case 1200:
+ csr = 0x66;
+ break;
+ case 2400:
+ csr = 0x88;
+ break;
+ case 4800:
+ csr = 0x99;
+ break;
+ default:
+ case 9600:
+ csr = 0xbb;
+ break;
+ case 19200:
+ csr = 0xcc;
+ break;
+ }
+
+ WRITE_SC_PORT(port, CR, CR_RES_MR);
+ WRITE_SC_PORT(port, MRx, mr1);
+ WRITE_SC_PORT(port, MRx, mr2);
+
+ WRITE_SC(port, ACR, 0x80);
+ WRITE_SC_PORT(port, CSR, csr);
+
+ /* reset tx and rx */
+ WRITE_SC_PORT(port, CR, CR_RES_RX);
+ WRITE_SC_PORT(port, CR, CR_RES_TX);
+
+ WRITE_SC_PORT(port, CR, CR_ENA_TX | CR_ENA_RX);
+ while ((READ_SC_PORT(port, SR) & ((1 << 3) | (1 << 2))) != 0xc)
+ udelay(2);
+
+ /* XXX */
+ uart_update_timeout(port, cflag,
+ (port->uartclk / (16 * quot)));
+
+ spin_unlock_irqrestore(&port->lock, flags);
+}
+
+static const char *sc26xx_type(struct uart_port *port)
+{
+ return "SC26XX";
+}
+
+static void sc26xx_release_port(struct uart_port *port)
+{
+}
+
+static int sc26xx_request_port(struct uart_port *port)
+{
+ return 0;
+}
+
+static void sc26xx_config_port(struct uart_port *port, int flags)
+{
+}
+
+static int sc26xx_verify_port(struct uart_port *port, struct serial_struct *ser)
+{
+ return -EINVAL;
+}
+
+static struct uart_ops sc26xx_ops = {
+ .tx_empty = sc26xx_tx_empty,
+ .set_mctrl = sc26xx_set_mctrl,
+ .get_mctrl = sc26xx_get_mctrl,
+ .stop_tx = sc26xx_stop_tx,
+ .start_tx = sc26xx_start_tx,
+ .stop_rx = sc26xx_stop_rx,
+ .enable_ms = sc26xx_enable_ms,
+ .break_ctl = sc26xx_break_ctl,
+ .startup = sc26xx_startup,
+ .shutdown = sc26xx_shutdown,
+ .set_termios = sc26xx_set_termios,
+ .type = sc26xx_type,
+ .release_port = sc26xx_release_port,
+ .request_port = sc26xx_request_port,
+ .config_port = sc26xx_config_port,
+ .verify_port = sc26xx_verify_port,
+};
+
+static struct uart_port *sc26xx_port;
+
+#ifdef CONFIG_SERIAL_SC26XX_CONSOLE
+static void sc26xx_console_putchar(struct uart_port *port, char c)
+{
+ unsigned long flags;
+ int limit = 1000000;
+
+ spin_lock_irqsave(&port->lock, flags);
+
+ while (limit-- > 0) {
+ if (READ_SC_PORT(port, SR) & SR_TXRDY) {
+ WRITE_SC_PORT(port, THR, c);
+ break;
+ }
+ udelay(2);
+ }
+
+ spin_unlock_irqrestore(&port->lock, flags);
+}
+
+static void sc26xx_console_write(struct console *con, const char *s, unsigned n)
+{
+ struct uart_port *port = sc26xx_port;
+ int i;
+
+ for (i = 0; i < n; i++) {
+ if (*s == '\n')
+ sc26xx_console_putchar(port, '\r');
+ sc26xx_console_putchar(port, *s++);
+ }
+}
+
+static int __init sc26xx_console_setup(struct console *con, char *options)
+{
+ struct uart_port *port = sc26xx_port;
+ int baud = 9600;
+ int bits = 8;
+ int parity = 'n';
+ int flow = 'n';
+
+ if (port->type != PORT_SC26XX)
+ return -1;
+
+ printk(KERN_INFO "Console: ttySC%d (SC26XX)\n", con->index);
+ if (options)
+ uart_parse_options(options, &baud, &parity, &bits, &flow);
+
+ return uart_set_options(port, con, baud, parity, bits, flow);
+}
+
+static struct uart_driver sc26xx_reg;
+static struct console sc26xx_console = {
+ .name = "ttySC",
+ .write = sc26xx_console_write,
+ .device = uart_console_device,
+ .setup = sc26xx_console_setup,
+ .flags = CON_PRINTBUFFER,
+ .index = -1,
+ .data = &sc26xx_reg,
+};
+#define SC26XX_CONSOLE &sc26xx_console
+#else
+#define SC26XX_CONSOLE NULL
+#endif
+
+static struct uart_driver sc26xx_reg = {
+ .owner = THIS_MODULE,
+ .driver_name = "SC26xx",
+ .dev_name = "ttySC",
+ .major = SC26XX_MAJOR,
+ .minor = SC26XX_MINOR_START,
+ .nr = SC26XX_NR,
+ .cons = SC26XX_CONSOLE,
+};
+
+static u8 sc26xx_flags2mask(unsigned int flags, unsigned int bitpos)
+{
+ unsigned int bit = (flags >> bitpos) & 15;
+
+ return bit ? (1 << (bit - 1)) : 0;
+}
+
+static void __devinit sc26xx_init_masks(struct uart_sc26xx_port *up,
+ int line, unsigned int data)
+{
+ up->dtr_mask[line] = sc26xx_flags2mask(data, 0);
+ up->rts_mask[line] = sc26xx_flags2mask(data, 4);
+ up->dsr_mask[line] = sc26xx_flags2mask(data, 8);
+ up->cts_mask[line] = sc26xx_flags2mask(data, 12);
+ up->dcd_mask[line] = sc26xx_flags2mask(data, 16);
+ up->ri_mask[line] = sc26xx_flags2mask(data, 20);
+}
+
+static int __devinit sc26xx_probe(struct platform_device *dev)
+{
+ struct resource *res;
+ struct uart_sc26xx_port *up;
+ unsigned int *sc26xx_data = dev->dev.platform_data;
+ int err;
+
+ res = platform_get_resource(dev, IORESOURCE_MEM, 0);
+ if (!res)
+ return -ENODEV;
+
+ up = kzalloc(sizeof *up, GFP_KERNEL);
+ if (unlikely(!up))
+ return -ENOMEM;
+
+ up->port[0].line = 0;
+ up->port[0].ops = &sc26xx_ops;
+ up->port[0].type = PORT_SC26XX;
+ up->port[0].uartclk = (29491200 / 16); /* arbitrary */
+
+ up->port[0].mapbase = res->start;
+ up->port[0].membase = ioremap_nocache(up->port[0].mapbase, 0x40);
+ up->port[0].iotype = UPIO_MEM;
+ up->port[0].irq = platform_get_irq(dev, 0);
+
+ up->port[0].dev = &dev->dev;
+
+ sc26xx_init_masks(up, 0, sc26xx_data[0]);
+
+ sc26xx_port = &up->port[0];
+
+ up->port[1].line = 1;
+ up->port[1].ops = &sc26xx_ops;
+ up->port[1].type = PORT_SC26XX;
+ up->port[1].uartclk = (29491200 / 16); /* arbitrary */
+
+ up->port[1].mapbase = up->port[0].mapbase;
+ up->port[1].membase = up->port[0].membase;
+ up->port[1].iotype = UPIO_MEM;
+ up->port[1].irq = up->port[0].irq;
+
+ up->port[1].dev = &dev->dev;
+
+ sc26xx_init_masks(up, 1, sc26xx_data[1]);
+
+ err = uart_register_driver(&sc26xx_reg);
+ if (err)
+ goto out_free_port;
+
+ sc26xx_reg.tty_driver->name_base = sc26xx_reg.minor;
+
+ err = uart_add_one_port(&sc26xx_reg, &up->port[0]);
+ if (err)
+ goto out_unregister_driver;
+
+ err = uart_add_one_port(&sc26xx_reg, &up->port[1]);
+ if (err)
+ goto out_remove_port0;
+
+ err = request_irq(up->port[0].irq, sc26xx_interrupt, 0, "sc26xx", up);
+ if (err)
+ goto out_remove_ports;
+
+ dev_set_drvdata(&dev->dev, up);
+ return 0;
+
+out_remove_ports:
+ uart_remove_one_port(&sc26xx_reg, &up->port[1]);
+out_remove_port0:
+ uart_remove_one_port(&sc26xx_reg, &up->port[0]);
+
+out_unregister_driver:
+ uart_unregister_driver(&sc26xx_reg);
+
+out_free_port:
+ kfree(up);
+ sc26xx_port = NULL;
+ return err;
+}
+
+
+static int __exit sc26xx_driver_remove(struct platform_device *dev)
+{
+ struct uart_sc26xx_port *up = dev_get_drvdata(&dev->dev);
+
+ free_irq(up->port[0].irq, up);
+
+ uart_remove_one_port(&sc26xx_reg, &up->port[0]);
+ uart_remove_one_port(&sc26xx_reg, &up->port[1]);
+
+ uart_unregister_driver(&sc26xx_reg);
+
+ kfree(up);
+ sc26xx_port = NULL;
+
+ dev_set_drvdata(&dev->dev, NULL);
+ return 0;
+}
+
+static struct platform_driver sc26xx_driver = {
+ .probe = sc26xx_probe,
+ .remove = __devexit_p(sc26xx_driver_remove),
+ .driver = {
+ .name = "SC26xx",
+ },
+};
+
+static int __init sc26xx_init(void)
+{
+ return platform_driver_register(&sc26xx_driver);
+}
+
+static void __exit sc26xx_exit(void)
+{
+ platform_driver_unregister(&sc26xx_driver);
+}
+
+module_init(sc26xx_init);
+module_exit(sc26xx_exit);
+
+
+MODULE_AUTHOR("Thomas Bogendörfer");
+MODULE_DESCRIPTION("SC681/SC2692 serial driver");
+MODULE_VERSION("1.0");
+MODULE_LICENSE("GPL");
projects / kernel / kernel-generic.git / commitdiff